Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
  omap: zoom: host should not pull up wl1271's irq line
  arm: plat-omap: iommu: fix request_mem_region() error path
  OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
  omap4: mux: Remove duplicate mux modes
  omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
  omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
  omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
  omap4: board-omap4panda: Initialise the serial pads
  omap3: board-3430sdp: Initialise the serial pads
  omap4: board-4430sdp: Initialise the serial pads
  omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
  omap2+: mux: Remove the use of IDLE flag
  omap2+: Add separate list for dynamic pads to mux
  perf: add OMAP support for the new power events
  OMAP4: Add IVA OPP enteries.
  OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
  OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
  OMAP3+: OPP: Replace voltage values with Macros
  OMAP3: wdtimer: Fix CORE idle transition
  Watchdog: omap_wdt: add fine grain runtime-pm
  ...

Fix up various conflicts in
 - arch/arm/mach-omap2/board-omap3evm.c
 - arch/arm/mach-omap2/clock3xxx_data.c
 - arch/arm/mach-omap2/usb-musb.c
 - arch/arm/plat-omap/include/plat/usb.h
 - drivers/usb/musb/musb_core.h

1 files changed, 93 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index ebe33df708bd..e2e605fe9138 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -29,6 +29,7 @@
 #include <linux/usb.h>
 
 #include <plat/usb.h>
+#include "control.h"
 
 /* OMAP control module register for UTMI PHY */
 #define CONTROL_DEV_CONF		0x300
@@ -162,3 +163,95 @@ int omap4430_phy_exit(struct device *dev)
 
 	return 0;
 }
+
+void am35x_musb_reset(void)
+{
+	u32	regval;
+
+	/* Reset the musb interface */
+	regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
+
+	regval |= AM35XX_USBOTGSS_SW_RST;
+	omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);
+
+	regval &= ~AM35XX_USBOTGSS_SW_RST;
+	omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);
+
+	regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
+}
+
+void am35x_musb_phy_power(u8 on)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(100);
+	u32 devconf2;
+
+	if (on) {
+		/*
+		 * Start the on-chip PHY and its PLL.
+		 */
+		devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+		devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
+		devconf2 |= CONF2_PHY_PLLON;
+
+		omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+
+		pr_info(KERN_INFO "Waiting for PHY clock good...\n");
+		while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
+				& CONF2_PHYCLKGD)) {
+			cpu_relax();
+
+			if (time_after(jiffies, timeout)) {
+				pr_err(KERN_ERR "musb PHY clock good timed out\n");
+				break;
+			}
+		}
+	} else {
+		/*
+		 * Power down the on-chip PHY.
+		 */
+		devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+		devconf2 &= ~CONF2_PHY_PLLON;
+		devconf2 |=  CONF2_PHYPWRDN | CONF2_OTGPWRDN;
+		omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+	}
+}
+
+void am35x_musb_clear_irq(void)
+{
+	u32 regval;
+
+	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
+	regval |= AM35XX_USBOTGSS_INT_CLR;
+	omap_ctrl_writel(regval, AM35XX_CONTROL_LVL_INTR_CLEAR);
+	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
+}
+
+void am35x_musb_set_mode(u8 musb_mode)
+{
+	u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+	devconf2 &= ~CONF2_OTGMODE;
+	switch (musb_mode) {
+#ifdef	CONFIG_USB_MUSB_HDRC_HCD
+	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
+		devconf2 |= CONF2_FORCE_HOST;
+		break;
+#endif
+#ifdef	CONFIG_USB_GADGET_MUSB_HDRC
+	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
+		devconf2 |= CONF2_FORCE_DEVICE;
+		break;
+#endif
+#ifdef	CONFIG_USB_MUSB_OTG
+	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
+		devconf2 |= CONF2_NO_OVERRIDE;
+		break;
+#endif
+	default:
+		pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
+	}
+
+	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+}