summaryrefslogtreecommitdiff
path: root/drivers/net/sky2.c
diff options
context:
space:
mode:
authorstephen hemminger <shemminger@vyatta.com>2011-07-07 05:50:58 +0000
committerDavid S. Miller <davem@davemloft.net>2011-07-08 08:53:33 -0700
commit8e11680f5e1abc85298c12a99e2b741249eadc0c (patch)
treeaf9f39ed9b3607e2480776d40a0845b1da612d69 /drivers/net/sky2.c
parentaa5ca96c8fffea769aedd795f48695112393dc89 (diff)
sky2: use correct Inter Packet Gap at 10/100mbit
This is another fix picked out of the vendor driver. The IPG value in the serial mode register is supposed to be programmed differently at lower speeds. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'drivers/net/sky2.c')
-rw-r--r--drivers/net/sky2.c25
1 files changed, 22 insertions, 3 deletions
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 3fc8683b2ff0..b1a675a94a17 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -714,6 +714,20 @@ static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port)
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
+/* configure IPG according to used link speed */
+static void sky2_set_ipg(struct sky2_port *sky2)
+{
+ u16 reg;
+
+ reg = gma_read16(sky2->hw, sky2->port, GM_SERIAL_MODE);
+ reg &= ~GM_SMOD_IPG_MSK;
+ if (sky2->speed > SPEED_100)
+ reg |= IPG_DATA_VAL(IPG_DATA_DEF_1000);
+ else
+ reg |= IPG_DATA_VAL(IPG_DATA_DEF_10_100);
+ gma_write16(sky2->hw, sky2->port, GM_SERIAL_MODE, reg);
+}
+
/* Enable Rx/Tx */
static void sky2_enable_rx_tx(struct sky2_port *sky2)
{
@@ -882,7 +896,7 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
/* serial mode register */
reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
- GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+ GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF_1000);
if (hw->dev[port]->mtu > ETH_DATA_LEN)
reg |= GM_SMOD_JUMBO_ENA;
@@ -2053,6 +2067,8 @@ static void sky2_link_up(struct sky2_port *sky2)
[FC_BOTH] = "both",
};
+ sky2_set_ipg(sky2);
+
sky2_enable_rx_tx(sky2);
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
@@ -2290,8 +2306,11 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu)
dev->mtu = new_mtu;
netdev_update_features(dev);
- mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
- GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+ mode = DATA_BLIND_VAL(DATA_BLIND_DEF) | GM_SMOD_VLAN_ENA;
+ if (sky2->speed > SPEED_100)
+ mode |= IPG_DATA_VAL(IPG_DATA_DEF_1000);
+ else
+ mode |= IPG_DATA_VAL(IPG_DATA_DEF_10_100);
if (dev->mtu > ETH_DATA_LEN)
mode |= GM_SMOD_JUMBO_ENA;