serial/8250_pci: Clear FIFOs for Intel ME Serial Over Lan device on BI

When using Serial Over Lan (SOL) over the virtual serial port in a Intel
management engine (ME) device, on device reset the serial FIFOs need to
be cleared to keep the FIFO indexes in-sync between the host and the
engine.

On a reset the serial device assertes BI, so using that as a cue FIFOs
are cleared.  So for this purpose a new handle_break callback has been
added.  One other problem is that the serial registers might temporarily
go to 0 on reset of this device.  So instead of using the IER register
read, if 0 returned use the ier value in uart_8250_port. This is hidden
under a custom serial_in.

Cc: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 39 insertions, 0 deletions

diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 858dca865d6a..024551acf874 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -17,6 +17,7 @@
 #include <linux/slab.h>
 #include <linux/delay.h>
 #include <linux/tty.h>
+#include <linux/serial_reg.h>
 #include <linux/serial_core.h>
 #include <linux/8250_pci.h>
 #include <linux/bitops.h>
@@ -1092,11 +1093,49 @@ static int skip_tx_en_setup(struct serial_private *priv,
 	return pci_default_setup(priv, board, port, idx);
 }
 
+static void kt_handle_break(struct uart_port *p)
+{
+	struct uart_8250_port *up =
+		container_of(p, struct uart_8250_port, port);
+	/*
+	 * On receipt of a BI, serial device in Intel ME (Intel
+	 * management engine) needs to have its fifos cleared for sane
+	 * SOL (Serial Over Lan) output.
+	 */
+	serial8250_clear_and_reinit_fifos(up);
+}
+
+static unsigned int kt_serial_in(struct uart_port *p, int offset)
+{
+	struct uart_8250_port *up =
+		container_of(p, struct uart_8250_port, port);
+	unsigned int val;
+
+	/*
+	 * When the Intel ME (management engine) gets reset its serial
+	 * port registers could return 0 momentarily.  Functions like
+	 * serial8250_console_write, read and save the IER, perform
+	 * some operation and then restore it.  In order to avoid
+	 * setting IER register inadvertently to 0, if the value read
+	 * is 0, double check with ier value in uart_8250_port and use
+	 * that instead.  up->ier should be the same value as what is
+	 * currently configured.
+	 */
+	val = inb(p->iobase + offset);
+	if (offset == UART_IER) {
+		if (val == 0)
+			val = up->ier;
+	}
+	return val;
+}
+
 static int kt_serial_setup(struct serial_private *priv,
 			   const struct pciserial_board *board,
 			   struct uart_port *port, int idx)
 {
 	port->flags |= UPF_BUG_THRE;
+	port->serial_in = kt_serial_in;
+	port->handle_break = kt_handle_break;
 	return skip_tx_en_setup(priv, board, port, idx);
 }