summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/fb/pxafb.txt84
-rw-r--r--arch/arm/mach-pxa/include/mach/regs-lcd.h34
-rw-r--r--drivers/video/Kconfig5
-rw-r--r--drivers/video/pxafb.c364
-rw-r--r--drivers/video/pxafb.h45
5 files changed, 516 insertions, 16 deletions
diff --git a/Documentation/fb/pxafb.txt b/Documentation/fb/pxafb.txt
index ad94b5ca0095..d143a0a749f9 100644
--- a/Documentation/fb/pxafb.txt
+++ b/Documentation/fb/pxafb.txt
@@ -56,3 +56,87 @@ outputen:POLARITY
pixclockpol:POLARITY
pixel clock polarity
0 => falling edge, 1 => rising edge
+
+
+Overlay Support for PXA27x and later LCD controllers
+====================================================
+
+ PXA27x and later processors support overlay1 and overlay2 on-top of the
+ base framebuffer (although under-neath the base is also possible). They
+ support palette and no-palette RGB formats, as well as YUV formats (only
+ available on overlay2). These overlays have dedicated DMA channels and
+ behave in a similar way as a framebuffer.
+
+ However, there are some differences between these overlay framebuffers
+ and normal framebuffers, as listed below:
+
+ 1. overlay can start at a 32-bit word aligned position within the base
+ framebuffer, which means they have a start (x, y). This information
+ is encoded into var->nonstd (no, var->xoffset and var->yoffset are
+ not for such purpose).
+
+ 2. overlay framebuffer is allocated dynamically according to specified
+ 'struct fb_var_screeninfo', the amount is decided by:
+
+ var->xres_virtual * var->yres_virtual * bpp
+
+ bpp = 16 -- for RGB565 or RGBT555
+ = 24 -- for YUV444 packed
+ = 24 -- for YUV444 planar
+ = 16 -- for YUV422 planar (1 pixel = 1 Y + 1/2 Cb + 1/2 Cr)
+ = 12 -- for YUV420 planar (1 pixel = 1 Y + 1/4 Cb + 1/4 Cr)
+
+ NOTE:
+
+ a. overlay does not support panning in x-direction, thus
+ var->xres_virtual will always be equal to var->xres
+
+ b. line length of overlay(s) must be on a 32-bit word boundary,
+ for YUV planar modes, it is a requirement for the component
+ with minimum bits per pixel, e.g. for YUV420, Cr component
+ for one pixel is actually 2-bits, it means the line length
+ should be a multiple of 16-pixels
+
+ c. starting horizontal position (XPOS) should start on a 32-bit
+ word boundary, otherwise the fb_check_var() will just fail.
+
+ d. the rectangle of the overlay should be within the base plane,
+ otherwise fail
+
+ Applications should follow the sequence below to operate an overlay
+ framebuffer:
+
+ a. open("/dev/fb[1-2]", ...)
+ b. ioctl(fd, FBIOGET_VSCREENINFO, ...)
+ c. modify 'var' with desired parameters:
+ 1) var->xres and var->yres
+ 2) larger var->yres_virtual if more memory is required,
+ usually for double-buffering
+ 3) var->nonstd for starting (x, y) and color format
+ 4) var->{red, green, blue, transp} if RGB mode is to be used
+ d. ioctl(fd, FBIOPUT_VSCREENINFO, ...)
+ e. ioctl(fd, FBIOGET_FSCREENINFO, ...)
+ f. mmap
+ g. ...
+
+ 3. for YUV planar formats, these are actually not supported within the
+ framebuffer framework, application has to take care of the offsets
+ and lengths of each component within the framebuffer.
+
+ 4. var->nonstd is used to pass starting (x, y) position and color format,
+ the detailed bit fields are shown below:
+
+ 31 23 20 10 0
+ +-----------------+---+----------+----------+
+ | ... unused ... |FOR| XPOS | YPOS |
+ +-----------------+---+----------+----------+
+
+ FOR - color format, as defined by OVERLAY_FORMAT_* in pxafb.h
+ 0 - RGB
+ 1 - YUV444 PACKED
+ 2 - YUV444 PLANAR
+ 3 - YUV422 PLANAR
+ 4 - YUR420 PLANAR
+
+ XPOS - starting horizontal position
+ YPOS - starting vertical position
diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h
index aff3b876a7bf..f82dcea792d9 100644
--- a/arch/arm/mach-pxa/include/mach/regs-lcd.h
+++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h
@@ -12,7 +12,8 @@
#define LCCR3 (0x00C) /* LCD Controller Control Register 3 */
#define LCCR4 (0x010) /* LCD Controller Control Register 4 */
#define LCCR5 (0x014) /* LCD Controller Control Register 5 */
-#define LCSR (0x038) /* LCD Controller Status Register */
+#define LCSR (0x038) /* LCD Controller Status Register 0 */
+#define LCSR1 (0x034) /* LCD Controller Status Register 1 */
#define LIIDR (0x03C) /* LCD Controller Interrupt ID Register */
#define TMEDRGBR (0x040) /* TMED RGB Seed Register */
#define TMEDCR (0x044) /* TMED Control Register */
@@ -25,6 +26,11 @@
#define FBR5 (0x110) /* DMA Channel 2 Frame Branch Register */
#define FBR6 (0x114) /* DMA Channel 2 Frame Branch Register */
+#define OVL1C1 (0x050) /* Overlay 1 Control Register 1 */
+#define OVL1C2 (0x060) /* Overlay 1 Control Register 2 */
+#define OVL2C1 (0x070) /* Overlay 2 Control Register 1 */
+#define OVL2C2 (0x080) /* Overlay 2 Control Register 2 */
+
#define CMDCR (0x100) /* Command Control Register */
#define PRSR (0x104) /* Panel Read Status Register */
@@ -42,16 +48,12 @@
#define LCCR4_PAL_FOR_MASK (3 << 15)
#define FDADR0 (0x200) /* DMA Channel 0 Frame Descriptor Address Register */
-#define FSADR0 (0x204) /* DMA Channel 0 Frame Source Address Register */
-#define FIDR0 (0x208) /* DMA Channel 0 Frame ID Register */
-#define LDCMD0 (0x20C) /* DMA Channel 0 Command Register */
#define FDADR1 (0x210) /* DMA Channel 1 Frame Descriptor Address Register */
-#define FSADR1 (0x214) /* DMA Channel 1 Frame Source Address Register */
-#define FIDR1 (0x218) /* DMA Channel 1 Frame ID Register */
-#define LDCMD1 (0x21C) /* DMA Channel 1 Command Register */
+#define FDADR2 (0x220) /* DMA Channel 2 Frame Descriptor Address Register */
+#define FDADR3 (0x230) /* DMA Channel 3 Frame Descriptor Address Register */
+#define FDADR4 (0x240) /* DMA Channel 4 Frame Descriptor Address Register */
+#define FDADR5 (0x250) /* DMA Channel 5 Frame Descriptor Address Register */
#define FDADR6 (0x260) /* DMA Channel 6 Frame Descriptor Address Register */
-#define FSADR6 (0x264) /* DMA Channel 6 Frame Source Address Register */
-#define FIDR6 (0x268) /* DMA Channel 6 Frame ID Register */
#define LCCR0_ENB (1 << 0) /* LCD Controller enable */
#define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */
@@ -151,8 +153,22 @@
#define LCSR_RD_ST (1 << 11) /* read status */
#define LCSR_CMD_INT (1 << 12) /* command interrupt */
+#define LCSR1_IU(x) (1 << ((x) + 23)) /* Input FIFO underrun */
+#define LCSR1_BS(x) (1 << ((x) + 15)) /* Branch Status */
+#define LCSR1_EOF(x) (1 << ((x) + 7)) /* End of Frame Status */
+#define LCSR1_SOF(x) (1 << ((x) - 1)) /* Start of Frame Status */
+
#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
+/* overlay control registers */
+#define OVLxC1_PPL(x) ((((x) - 1) & 0x3ff) << 0) /* Pixels Per Line */
+#define OVLxC1_LPO(x) ((((x) - 1) & 0x3ff) << 10) /* Number of Lines */
+#define OVLxC1_BPP(x) (((x) & 0xf) << 20) /* Bits Per Pixel */
+#define OVLxC1_OEN (1 << 31) /* Enable bit for Overlay */
+#define OVLxC2_XPOS(x) (((x) & 0x3ff) << 0) /* Horizontal Position */
+#define OVLxC2_YPOS(x) (((x) & 0x3ff) << 10) /* Vertical Position */
+#define OVL2C2_PFOR(x) (((x) & 0x7) << 20) /* Pixel Format */
+
/* smartpanel related */
#define PRSR_DATA(x) ((x) & 0xff) /* Panel Data */
#define PRSR_A0 (1 << 8) /* Read Data Source */
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 3f3ce13fef43..486d81ca02a3 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1817,6 +1817,11 @@ config FB_PXA
If unsure, say N.
+config FB_PXA_OVERLAY
+ bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
+ default n
+ depends on FB_PXA && (PXA27x || PXA3xx)
+
config FB_PXA_SMARTPANEL
bool "PXA Smartpanel LCD support"
default n
diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c
index 7935706a7565..3a41ea10e8ec 100644
--- a/drivers/video/pxafb.c
+++ b/drivers/video/pxafb.c
@@ -20,6 +20,16 @@
*
* linux-arm-kernel@lists.arm.linux.org.uk
*
+ * Add support for overlay1 and overlay2 based on pxafb_overlay.c:
+ *
+ * Copyright (C) 2004, Intel Corporation
+ *
+ * 2003/08/27: <yu.tang@intel.com>
+ * 2004/03/10: <stanley.cai@intel.com>
+ * 2004/10/28: <yan.yin@intel.com>
+ *
+ * Copyright (C) 2006-2008 Marvell International Ltd.
+ * All Rights Reserved
*/
#include <linux/module.h>
@@ -72,6 +82,8 @@ static int pxafb_activate_var(struct fb_var_screeninfo *var,
struct pxafb_info *);
static void set_ctrlr_state(struct pxafb_info *fbi, u_int state);
static void setup_base_frame(struct pxafb_info *fbi, int branch);
+static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
+ unsigned long offset, size_t size);
static unsigned long video_mem_size = 0;
@@ -581,6 +593,330 @@ static struct fb_ops pxafb_ops = {
.fb_blank = pxafb_blank,
};
+#ifdef CONFIG_FB_PXA_OVERLAY
+static void overlay1fb_setup(struct pxafb_layer *ofb)
+{
+ int size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual;
+ unsigned long start = ofb->video_mem_phys;
+ setup_frame_dma(ofb->fbi, DMA_OV1, PAL_NONE, start, size);
+}
+
+/* Depending on the enable status of overlay1/2, the DMA should be
+ * updated from FDADRx (when disabled) or FBRx (when enabled).
+ */
+static void overlay1fb_enable(struct pxafb_layer *ofb)
+{
+ int enabled = lcd_readl(ofb->fbi, OVL1C1) & OVLxC1_OEN;
+ uint32_t fdadr1 = ofb->fbi->fdadr[DMA_OV1] | (enabled ? 0x1 : 0);
+
+ lcd_writel(ofb->fbi, enabled ? FBR1 : FDADR1, fdadr1);
+ lcd_writel(ofb->fbi, OVL1C2, ofb->control[1]);
+ lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] | OVLxC1_OEN);
+}
+
+static void overlay1fb_disable(struct pxafb_layer *ofb)
+{
+ uint32_t lccr5 = lcd_readl(ofb->fbi, LCCR5);
+
+ lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] & ~OVLxC1_OEN);
+
+ lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(1));
+ lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(1));
+ lcd_writel(ofb->fbi, FBR1, ofb->fbi->fdadr[DMA_OV1] | 0x3);
+
+ if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0)
+ pr_warning("%s: timeout disabling overlay1\n", __func__);
+
+ lcd_writel(ofb->fbi, LCCR5, lccr5);
+}
+
+static void overlay2fb_setup(struct pxafb_layer *ofb)
+{
+ int size, div = 1, pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd);
+ unsigned long start[3] = { ofb->video_mem_phys, 0, 0 };
+
+ if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED) {
+ size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual;
+ setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size);
+ } else {
+ size = ofb->fb.var.xres_virtual * ofb->fb.var.yres_virtual;
+ switch (pfor) {
+ case OVERLAY_FORMAT_YUV444_PLANAR: div = 1; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: div = 2; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: div = 4; break;
+ }
+ start[1] = start[0] + size;
+ start[2] = start[1] + size / div;
+ setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size);
+ setup_frame_dma(ofb->fbi, DMA_OV2_Cb, -1, start[1], size / div);
+ setup_frame_dma(ofb->fbi, DMA_OV2_Cr, -1, start[2], size / div);
+ }
+}
+
+static void overlay2fb_enable(struct pxafb_layer *ofb)
+{
+ int pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd);
+ int enabled = lcd_readl(ofb->fbi, OVL2C1) & OVLxC1_OEN;
+ uint32_t fdadr2 = ofb->fbi->fdadr[DMA_OV2_Y] | (enabled ? 0x1 : 0);
+ uint32_t fdadr3 = ofb->fbi->fdadr[DMA_OV2_Cb] | (enabled ? 0x1 : 0);
+ uint32_t fdadr4 = ofb->fbi->fdadr[DMA_OV2_Cr] | (enabled ? 0x1 : 0);
+
+ if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED)
+ lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2);
+ else {
+ lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2);
+ lcd_writel(ofb->fbi, enabled ? FBR3 : FDADR3, fdadr3);
+ lcd_writel(ofb->fbi, enabled ? FBR4 : FDADR4, fdadr4);
+ }
+ lcd_writel(ofb->fbi, OVL2C2, ofb->control[1]);
+ lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] | OVLxC1_OEN);
+}
+
+static void overlay2fb_disable(struct pxafb_layer *ofb)
+{
+ uint32_t lccr5 = lcd_readl(ofb->fbi, LCCR5);
+
+ lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] & ~OVLxC1_OEN);
+
+ lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(2));
+ lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(2));
+ lcd_writel(ofb->fbi, FBR2, ofb->fbi->fdadr[DMA_OV2_Y] | 0x3);
+ lcd_writel(ofb->fbi, FBR3, ofb->fbi->fdadr[DMA_OV2_Cb] | 0x3);
+ lcd_writel(ofb->fbi, FBR4, ofb->fbi->fdadr[DMA_OV2_Cr] | 0x3);
+
+ if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0)
+ pr_warning("%s: timeout disabling overlay2\n", __func__);
+}
+
+static struct pxafb_layer_ops ofb_ops[] = {
+ [0] = {
+ .enable = overlay1fb_enable,
+ .disable = overlay1fb_disable,
+ .setup = overlay1fb_setup,
+ },
+ [1] = {
+ .enable = overlay2fb_enable,
+ .disable = overlay2fb_disable,
+ .setup = overlay2fb_setup,
+ },
+};
+
+static int overlayfb_open(struct fb_info *info, int user)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer *)info;
+
+ /* no support for framebuffer console on overlay */
+ if (user == 0)
+ return -ENODEV;
+
+ /* allow only one user at a time */
+ if (atomic_inc_and_test(&ofb->usage))
+ return -EBUSY;
+
+ /* unblank the base framebuffer */
+ fb_blank(&ofb->fbi->fb, FB_BLANK_UNBLANK);
+ return 0;
+}
+
+static int overlayfb_release(struct fb_info *info, int user)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer*) info;
+
+ atomic_dec(&ofb->usage);
+ ofb->ops->disable(ofb);
+
+ free_pages_exact(ofb->video_mem, ofb->video_mem_size);
+ ofb->video_mem = NULL;
+ ofb->video_mem_size = 0;
+ return 0;
+}
+
+static int overlayfb_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer *)info;
+ struct fb_var_screeninfo *base_var = &ofb->fbi->fb.var;
+ int xpos, ypos, pfor, bpp;
+
+ xpos = NONSTD_TO_XPOS(var->nonstd);
+ ypos = NONSTD_TO_XPOS(var->nonstd);
+ pfor = NONSTD_TO_PFOR(var->nonstd);
+
+ bpp = pxafb_var_to_bpp(var);
+ if (bpp < 0)
+ return -EINVAL;
+
+ /* no support for YUV format on overlay1 */
+ if (ofb->id == OVERLAY1 && pfor != 0)
+ return -EINVAL;
+
+ /* for YUV packed formats, bpp = 'minimum bpp of YUV components' */
+ switch (pfor) {
+ case OVERLAY_FORMAT_RGB:
+ bpp = pxafb_var_to_bpp(var);
+ if (bpp < 0)
+ return -EINVAL;
+
+ pxafb_set_pixfmt(var, var_to_depth(var));
+ break;
+ case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 8; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 4; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 2; break;
+ default:
+ return -EINVAL;
+ }
+
+ /* each line must start at a 32-bit word boundary */
+ if ((xpos * bpp) % 32)
+ return -EINVAL;
+
+ /* xres must align on 32-bit word boundary */
+ var->xres = roundup(var->xres * bpp, 32) / bpp;
+
+ if ((xpos + var->xres > base_var->xres) ||
+ (ypos + var->yres > base_var->yres))
+ return -EINVAL;
+
+ var->xres_virtual = var->xres;
+ var->yres_virtual = max(var->yres, var->yres_virtual);
+ return 0;
+}
+
+static int overlayfb_map_video_memory(struct pxafb_layer *ofb)
+{
+ struct fb_var_screeninfo *var = &ofb->fb.var;
+ int pfor = NONSTD_TO_PFOR(var->nonstd);
+ int size, bpp = 0;
+
+ switch (pfor) {
+ case OVERLAY_FORMAT_RGB: bpp = var->bits_per_pixel; break;
+ case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 16; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 12; break;
+ }
+
+ ofb->fb.fix.line_length = var->xres_virtual * bpp / 8;
+
+ size = PAGE_ALIGN(ofb->fb.fix.line_length * var->yres_virtual);
+
+ /* don't re-allocate if the original video memory is enough */
+ if (ofb->video_mem) {
+ if (ofb->video_mem_size >= size)
+ return 0;
+
+ free_pages_exact(ofb->video_mem, ofb->video_mem_size);
+ }
+
+ ofb->video_mem = alloc_pages_exact(size, GFP_KERNEL | __GFP_ZERO);
+ if (ofb->video_mem == NULL)
+ return -ENOMEM;
+
+ ofb->video_mem_phys = virt_to_phys(ofb->video_mem);
+ ofb->video_mem_size = size;
+
+ ofb->fb.fix.smem_start = ofb->video_mem_phys;
+ ofb->fb.fix.smem_len = ofb->fb.fix.line_length * var->yres_virtual;
+ ofb->fb.screen_base = ofb->video_mem;
+ return 0;
+}
+
+static int overlayfb_set_par(struct fb_info *info)
+{
+ struct pxafb_layer *ofb = (struct pxafb_layer *)info;
+ struct fb_var_screeninfo *var = &info->var;
+ int xpos, ypos, pfor, bpp, ret;
+
+ ret = overlayfb_map_video_memory(ofb);
+ if (ret)
+ return ret;
+
+ bpp = pxafb_var_to_bpp(var);
+ xpos = NONSTD_TO_XPOS(var->nonstd);
+ ypos = NONSTD_TO_XPOS(var->nonstd);
+ pfor = NONSTD_TO_PFOR(var->nonstd);
+
+ ofb->control[0] = OVLxC1_PPL(var->xres) | OVLxC1_LPO(var->yres) |
+ OVLxC1_BPP(bpp);
+ ofb->control[1] = OVLxC2_XPOS(xpos) | OVLxC2_YPOS(ypos);
+
+ if (ofb->id == OVERLAY2)
+ ofb->control[1] |= OVL2C2_PFOR(pfor);
+
+ ofb->ops->setup(ofb);
+ ofb->ops->enable(ofb);
+ return 0;
+}
+
+static struct fb_ops overlay_fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_open = overlayfb_open,
+ .fb_release = overlayfb_release,
+ .fb_check_var = overlayfb_check_var,
+ .fb_set_par = overlayfb_set_par,
+};
+
+static void __devinit init_pxafb_overlay(struct pxafb_info *fbi,
+ struct pxafb_layer *ofb, int id)
+{
+ sprintf(ofb->fb.fix.id, "overlay%d", id + 1);
+
+ ofb->fb.fix.type = FB_TYPE_PACKED_PIXELS;
+ ofb->fb.fix.xpanstep = 0;
+ ofb->fb.fix.ypanstep = 1;
+
+ ofb->fb.var.activate = FB_ACTIVATE_NOW;
+ ofb->fb.var.height = -1;
+ ofb->fb.var.width = -1;
+ ofb->fb.var.vmode = FB_VMODE_NONINTERLACED;
+
+ ofb->fb.fbops = &overlay_fb_ops;
+ ofb->fb.flags = FBINFO_FLAG_DEFAULT;
+ ofb->fb.node = -1;
+ ofb->fb.pseudo_palette = NULL;
+
+ ofb->id = id;
+ ofb->ops = &ofb_ops[id];
+ atomic_set(&ofb->usage, 0);
+ ofb->fbi = fbi;
+ init_completion(&ofb->branch_done);
+}
+
+static int __devinit pxafb_overlay_init(struct pxafb_info *fbi)
+{
+ int i, ret;
+
+ for (i = 0; i < 2; i++) {
+ init_pxafb_overlay(fbi, &fbi->overlay[i], i);
+ ret = register_framebuffer(&fbi->overlay[i].fb);
+ if (ret) {
+ dev_err(fbi->dev, "failed to register overlay %d\n", i);
+ return ret;
+ }
+ }
+
+ /* mask all IU/BS/EOF/SOF interrupts */
+ lcd_writel(fbi, LCCR5, ~0);
+
+ /* place overlay(s) on top of base */
+ fbi->lccr0 |= LCCR0_OUC;
+ pr_info("PXA Overlay driver loaded successfully!\n");
+ return 0;
+}
+
+static void __devexit pxafb_overlay_exit(struct pxafb_info *fbi)
+{
+ int i;
+
+ for (i = 0; i < 2; i++)
+ unregister_framebuffer(&fbi->overlay[i].fb);
+}
+#else
+static inline void pxafb_overlay_init(struct pxafb_info *fbi) {}
+static inline void pxafb_overlay_exit(struct pxafb_info *fbi) {}
+#endif /* CONFIG_FB_PXA_OVERLAY */
+
/*
* Calculate the PCD value from the clock rate (in picoseconds).
* We take account of the PPCR clock setting.
@@ -660,7 +996,7 @@ unsigned long pxafb_get_hsync_time(struct device *dev)
EXPORT_SYMBOL(pxafb_get_hsync_time);
static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
- unsigned int offset, size_t size)
+ unsigned long start, size_t size)
{
struct pxafb_dma_descriptor *dma_desc, *pal_desc;
unsigned int dma_desc_off, pal_desc_off;
@@ -671,7 +1007,7 @@ static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
dma_desc = &fbi->dma_buff->dma_desc[dma];
dma_desc_off = offsetof(struct pxafb_dma_buff, dma_desc[dma]);
- dma_desc->fsadr = fbi->video_mem_phys + offset;
+ dma_desc->fsadr = start;
dma_desc->fidr = 0;
dma_desc->ldcmd = size;
@@ -705,14 +1041,14 @@ static void setup_base_frame(struct pxafb_info *fbi, int branch)
{
struct fb_var_screeninfo *var = &fbi->fb.var;
struct fb_fix_screeninfo *fix = &fbi->fb.fix;
- unsigned int nbytes, offset;
- int dma, pal, bpp = var->bits_per_pixel;
+ int nbytes, dma, pal, bpp = var->bits_per_pixel;
+ unsigned long offset;
dma = DMA_BASE + (branch ? DMA_MAX : 0);
pal = (bpp >= 16) ? PAL_NONE : PAL_BASE + (branch ? PAL_MAX : 0);
nbytes = fix->line_length * var->yres;
- offset = fix->line_length * var->yoffset;
+ offset = fix->line_length * var->yoffset + fbi->video_mem_phys;
if (fbi->lccr0 & LCCR0_SDS) {
nbytes = nbytes / 2;
@@ -1090,8 +1426,9 @@ static void pxafb_disable_controller(struct pxafb_info *fbi)
static irqreturn_t pxafb_handle_irq(int irq, void *dev_id)
{
struct pxafb_info *fbi = dev_id;
- unsigned int lccr0, lcsr = lcd_readl(fbi, LCSR);
+ unsigned int lccr0, lcsr, lcsr1;
+ lcsr = lcd_readl(fbi, LCSR);
if (lcsr & LCSR_LDD) {
lccr0 = lcd_readl(fbi, LCCR0);
lcd_writel(fbi, LCCR0, lccr0 | LCCR0_LDM);
@@ -1102,8 +1439,18 @@ static irqreturn_t pxafb_handle_irq(int irq, void *dev_id)
if (lcsr & LCSR_CMD_INT)
complete(&fbi->command_done);
#endif
-
lcd_writel(fbi, LCSR, lcsr);
+
+#ifdef CONFIG_FB_PXA_OVERLAY
+ lcsr1 = lcd_readl(fbi, LCSR1);
+ if (lcsr1 & LCSR1_BS(1))
+ complete(&fbi->overlay[0].branch_done);
+
+ if (lcsr1 & LCSR1_BS(2))
+ complete(&fbi->overlay[1].branch_done);
+
+ lcd_writel(fbi, LCSR1, lcsr1);
+#endif
return IRQ_HANDLED;
}
@@ -1802,6 +2149,8 @@ static int __devinit pxafb_probe(struct platform_device *dev)
goto failed_free_cmap;
}
+ pxafb_overlay_init(fbi);
+
#ifdef CONFIG_CPU_FREQ
fbi->freq_transition.notifier_call = pxafb_freq_transition;
fbi->freq_policy.notifier_call = pxafb_freq_policy;
@@ -1852,6 +2201,7 @@ static int __devexit pxafb_remove(struct platform_device *dev)
info = &fbi->fb;
+ pxafb_overlay_exit(fbi);
unregister_framebuffer(info);
pxafb_disable_controller(fbi);
diff --git a/drivers/video/pxafb.h b/drivers/video/pxafb.h
index ae3cbc1ca64f..2353521c5c8c 100644
--- a/drivers/video/pxafb.h
+++ b/drivers/video/pxafb.h
@@ -64,6 +64,47 @@ struct pxafb_dma_buff {
struct pxafb_dma_descriptor dma_desc[DMA_MAX * 2];
};
+enum {
+ OVERLAY1,
+ OVERLAY2,
+};
+
+enum {
+ OVERLAY_FORMAT_RGB = 0,
+ OVERLAY_FORMAT_YUV444_PACKED,
+ OVERLAY_FORMAT_YUV444_PLANAR,
+ OVERLAY_FORMAT_YUV422_PLANAR,
+ OVERLAY_FORMAT_YUV420_PLANAR,
+};
+
+#define NONSTD_TO_XPOS(x) (((x) >> 0) & 0x3ff)
+#define NONSTD_TO_YPOS(x) (((x) >> 10) & 0x3ff)
+#define NONSTD_TO_PFOR(x) (((x) >> 20) & 0x7)
+
+struct pxafb_layer;
+
+struct pxafb_layer_ops {
+ void (*enable)(struct pxafb_layer *);
+ void (*disable)(struct pxafb_layer *);
+ void (*setup)(struct pxafb_layer *);
+};
+
+struct pxafb_layer {
+ struct fb_info fb;
+ int id;
+ atomic_t usage;
+ uint32_t control[2];
+
+ struct pxafb_layer_ops *ops;
+
+ void __iomem *video_mem;
+ unsigned long video_mem_phys;
+ size_t video_mem_size;
+ struct completion branch_done;
+
+ struct pxafb_info *fbi;
+};
+
struct pxafb_info {
struct fb_info fb;
struct device *dev;
@@ -114,6 +155,10 @@ struct pxafb_info {
struct task_struct *smart_thread;
#endif
+#ifdef CONFIG_FB_PXA_OVERLAY
+ struct pxafb_layer overlay[2];
+#endif
+
#ifdef CONFIG_CPU_FREQ
struct notifier_block freq_transition;
struct notifier_block freq_policy;