diff options
28 files changed, 25247 insertions, 121 deletions
diff --git a/Documentation/networking/README.ipw2100 b/Documentation/networking/README.ipw2100 new file mode 100644 index 000000000000..2046948b020d --- /dev/null +++ b/Documentation/networking/README.ipw2100 @@ -0,0 +1,246 @@ + +=========================== +Intel(R) PRO/Wireless 2100 Network Connection Driver for Linux +README.ipw2100 + +March 14, 2005 + +=========================== +Index +--------------------------- +0. Introduction +1. Release 1.1.0 Current Features +2. Command Line Parameters +3. Sysfs Helper Files +4. Radio Kill Switch +5. Dynamic Firmware +6. Power Management +7. Support +8. License + + +=========================== +0. Introduction +------------ ----- ----- ---- --- -- - + +This document provides a brief overview of the features supported by the +IPW2100 driver project. The main project website, where the latest +development version of the driver can be found, is: + + http://ipw2100.sourceforge.net + +There you can find the not only the latest releases, but also information about +potential fixes and patches, as well as links to the development mailing list +for the driver project. + + +=========================== +1. Release 1.1.0 Current Supported Features +--------------------------- +- Managed (BSS) and Ad-Hoc (IBSS) +- WEP (shared key and open) +- Wireless Tools support +- 802.1x (tested with XSupplicant 1.0.1) + +Enabled (but not supported) features: +- Monitor/RFMon mode +- WPA/WPA2 + +The distinction between officially supported and enabled is a reflection +on the amount of validation and interoperability testing that has been +performed on a given feature. + + +=========================== +2. Command Line Parameters +--------------------------- + +If the driver is built as a module, the following optional parameters are used +by entering them on the command line with the modprobe command using this +syntax: + + modprobe ipw2100 [<option>=<VAL1><,VAL2>...] + +For example, to disable the radio on driver loading, enter: + + modprobe ipw2100 disable=1 + +The ipw2100 driver supports the following module parameters: + +Name Value Example: +debug 0x0-0xffffffff debug=1024 +mode 0,1,2 mode=1 /* AdHoc */ +channel int channel=3 /* Only valid in AdHoc or Monitor */ +associate boolean associate=0 /* Do NOT auto associate */ +disable boolean disable=1 /* Do not power the HW */ + + +=========================== +3. Sysfs Helper Files +--------------------------- + +There are several ways to control the behavior of the driver. Many of the +general capabilities are exposed through the Wireless Tools (iwconfig). There +are a few capabilities that are exposed through entries in the Linux Sysfs. + + +----- Driver Level ------ +For the driver level files, look in /sys/bus/pci/drivers/ipw2100/ + + debug_level + + This controls the same global as the 'debug' module parameter. For + information on the various debugging levels available, run the 'dvals' + script found in the driver source directory. + + NOTE: 'debug_level' is only enabled if CONFIG_IPW2100_DEBUG is turn + on. + +----- Device Level ------ +For the device level files look in + + /sys/bus/pci/drivers/ipw2100/{PCI-ID}/ + +For example: + /sys/bus/pci/drivers/ipw2100/0000:02:01.0 + +For the device level files, see /sys/bus/pci/drivers/ipw2100: + + rf_kill + read - + 0 = RF kill not enabled (radio on) + 1 = SW based RF kill active (radio off) + 2 = HW based RF kill active (radio off) + 3 = Both HW and SW RF kill active (radio off) + write - + 0 = If SW based RF kill active, turn the radio back on + 1 = If radio is on, activate SW based RF kill + + NOTE: If you enable the SW based RF kill and then toggle the HW + based RF kill from ON -> OFF -> ON, the radio will NOT come back on + + +=========================== +4. Radio Kill Switch +--------------------------- +Most laptops provide the ability for the user to physically disable the radio. +Some vendors have implemented this as a physical switch that requires no +software to turn the radio off and on. On other laptops, however, the switch +is controlled through a button being pressed and a software driver then making +calls to turn the radio off and on. This is referred to as a "software based +RF kill switch" + +See the Sysfs helper file 'rf_kill' for determining the state of the RF switch +on your system. + + +=========================== +5. Dynamic Firmware +--------------------------- +As the firmware is licensed under a restricted use license, it can not be +included within the kernel sources. To enable the IPW2100 you will need a +firmware image to load into the wireless NIC's processors. + +You can obtain these images from <http://ipw2100.sf.net/firmware.php>. + +See INSTALL for instructions on installing the firmware. + + +=========================== +6. Power Management +--------------------------- +The IPW2100 supports the configuration of the Power Save Protocol +through a private wireless extension interface. The IPW2100 supports +the following different modes: + + off No power management. Radio is always on. + on Automatic power management + 1-5 Different levels of power management. The higher the + number the greater the power savings, but with an impact to + packet latencies. + +Power management works by powering down the radio after a certain +interval of time has passed where no packets are passed through the +radio. Once powered down, the radio remains in that state for a given +period of time. For higher power savings, the interval between last +packet processed to sleep is shorter and the sleep period is longer. + +When the radio is asleep, the access point sending data to the station +must buffer packets at the AP until the station wakes up and requests +any buffered packets. If you have an AP that does not correctly support +the PSP protocol you may experience packet loss or very poor performance +while power management is enabled. If this is the case, you will need +to try and find a firmware update for your AP, or disable power +management (via `iwconfig eth1 power off`) + +To configure the power level on the IPW2100 you use a combination of +iwconfig and iwpriv. iwconfig is used to turn power management on, off, +and set it to auto. + + iwconfig eth1 power off Disables radio power down + iwconfig eth1 power on Enables radio power management to + last set level (defaults to AUTO) + iwpriv eth1 set_power 0 Sets power level to AUTO and enables + power management if not previously + enabled. + iwpriv eth1 set_power 1-5 Set the power level as specified, + enabling power management if not + previously enabled. + +You can view the current power level setting via: + + iwpriv eth1 get_power + +It will return the current period or timeout that is configured as a string +in the form of xxxx/yyyy (z) where xxxx is the timeout interval (amount of +time after packet processing), yyyy is the period to sleep (amount of time to +wait before powering the radio and querying the access point for buffered +packets), and z is the 'power level'. If power management is turned off the +xxxx/yyyy will be replaced with 'off' -- the level reported will be the active +level if `iwconfig eth1 power on` is invoked. + + +=========================== +7. Support +--------------------------- + +For general development information and support, +go to: + + http://ipw2100.sf.net/ + +The ipw2100 1.1.0 driver and firmware can be downloaded from: + + http://support.intel.com + +For installation support on the ipw2100 1.1.0 driver on Linux kernels +2.6.8 or greater, email support is available from: + + http://supportmail.intel.com + +=========================== +8. License +--------------------------- + + Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of the GNU General Public License (version 2) as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + License Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + diff --git a/Documentation/networking/README.ipw2200 b/Documentation/networking/README.ipw2200 new file mode 100644 index 000000000000..6916080c5f03 --- /dev/null +++ b/Documentation/networking/README.ipw2200 @@ -0,0 +1,300 @@ + +Intel(R) PRO/Wireless 2915ABG Driver for Linux in support of: + +Intel(R) PRO/Wireless 2200BG Network Connection +Intel(R) PRO/Wireless 2915ABG Network Connection + +Note: The Intel(R) PRO/Wireless 2915ABG Driver for Linux and Intel(R) +PRO/Wireless 2200BG Driver for Linux is a unified driver that works on +both hardware adapters listed above. In this document the Intel(R) +PRO/Wireless 2915ABG Driver for Linux will be used to reference the +unified driver. + +Copyright (C) 2004-2005, Intel Corporation + +README.ipw2200 + +Version: 1.0.0 +Date : January 31, 2005 + + +Index +----------------------------------------------- +1. Introduction +1.1. Overview of features +1.2. Module parameters +1.3. Wireless Extension Private Methods +1.4. Sysfs Helper Files +2. About the Version Numbers +3. Support +4. License + + +1. Introduction +----------------------------------------------- +The following sections attempt to provide a brief introduction to using +the Intel(R) PRO/Wireless 2915ABG Driver for Linux. + +This document is not meant to be a comprehensive manual on +understanding or using wireless technologies, but should be sufficient +to get you moving without wires on Linux. + +For information on building and installing the driver, see the INSTALL +file. + + +1.1. Overview of Features +----------------------------------------------- +The current release (1.0.0) supports the following features: + ++ BSS mode (Infrastructure, Managed) ++ IBSS mode (Ad-Hoc) ++ WEP (OPEN and SHARED KEY mode) ++ 802.1x EAP via wpa_supplicant and xsupplicant ++ Wireless Extension support ++ Full B and G rate support (2200 and 2915) ++ Full A rate support (2915 only) ++ Transmit power control ++ S state support (ACPI suspend/resume) ++ long/short preamble support + + + +1.2. Command Line Parameters +----------------------------------------------- + +Like many modules used in the Linux kernel, the Intel(R) PRO/Wireless +2915ABG Driver for Linux allows certain configuration options to be +provided as module parameters. The most common way to specify a module +parameter is via the command line. + +The general form is: + +% modprobe ipw2200 parameter=value + +Where the supported parameter are: + + associate + Set to 0 to disable the auto scan-and-associate functionality of the + driver. If disabled, the driver will not attempt to scan + for and associate to a network until it has been configured with + one or more properties for the target network, for example configuring + the network SSID. Default is 1 (auto-associate) + + Example: % modprobe ipw2200 associate=0 + + auto_create + Set to 0 to disable the auto creation of an Ad-Hoc network + matching the channel and network name parameters provided. + Default is 1. + + channel + channel number for association. The normal method for setting + the channel would be to use the standard wireless tools + (i.e. `iwconfig eth1 channel 10`), but it is useful sometimes + to set this while debugging. Channel 0 means 'ANY' + + debug + If using a debug build, this is used to control the amount of debug + info is logged. See the 'dval' and 'load' script for more info on + how to use this (the dval and load scripts are provided as part + of the ipw2200 development snapshot releases available from the + SourceForge project at http://ipw2200.sf.net) + + mode + Can be used to set the default mode of the adapter. + 0 = Managed, 1 = Ad-Hoc + + +1.3. Wireless Extension Private Methods +----------------------------------------------- + +As an interface designed to handle generic hardware, there are certain +capabilities not exposed through the normal Wireless Tool interface. As +such, a provision is provided for a driver to declare custom, or +private, methods. The Intel(R) PRO/Wireless 2915ABG Driver for Linux +defines several of these to configure various settings. + +The general form of using the private wireless methods is: + + % iwpriv $IFNAME method parameters + +Where $IFNAME is the interface name the device is registered with +(typically eth1, customized via one of the various network interface +name managers, such as ifrename) + +The supported private methods are: + + get_mode + Can be used to report out which IEEE mode the driver is + configured to support. Example: + + % iwpriv eth1 get_mode + eth1 get_mode:802.11bg (6) + + set_mode + Can be used to configure which IEEE mode the driver will + support. + + Usage: + % iwpriv eth1 set_mode {mode} + Where {mode} is a number in the range 1-7: + 1 802.11a (2915 only) + 2 802.11b + 3 802.11ab (2915 only) + 4 802.11g + 5 802.11ag (2915 only) + 6 802.11bg + 7 802.11abg (2915 only) + + get_preamble + Can be used to report configuration of preamble length. + + set_preamble + Can be used to set the configuration of preamble length: + + Usage: + % iwpriv eth1 set_preamble {mode} + Where {mode} is one of: + 1 Long preamble only + 0 Auto (long or short based on connection) + + +1.4. Sysfs Helper Files: +----------------------------------------------- + +The Linux kernel provides a pseudo file system that can be used to +access various components of the operating system. The Intel(R) +PRO/Wireless 2915ABG Driver for Linux exposes several configuration +parameters through this mechanism. + +An entry in the sysfs can support reading and/or writing. You can +typically query the contents of a sysfs entry through the use of cat, +and can set the contents via echo. For example: + +% cat /sys/bus/pci/drivers/ipw2200/debug_level + +Will report the current debug level of the driver's logging subsystem +(only available if CONFIG_IPW_DEBUG was configured when the driver was +built). + +You can set the debug level via: + +% echo $VALUE > /sys/bus/pci/drivers/ipw2200/debug_level + +Where $VALUE would be a number in the case of this sysfs entry. The +input to sysfs files does not have to be a number. For example, the +firmware loader used by hotplug utilizes sysfs entries for transferring +the firmware image from user space into the driver. + +The Intel(R) PRO/Wireless 2915ABG Driver for Linux exposes sysfs entries +at two levels -- driver level, which apply to all instances of the +driver (in the event that there are more than one device installed) and +device level, which applies only to the single specific instance. + + +1.4.1 Driver Level Sysfs Helper Files +----------------------------------------------- + +For the driver level files, look in /sys/bus/pci/drivers/ipw2200/ + + debug_level + + This controls the same global as the 'debug' module parameter + + +1.4.2 Device Level Sysfs Helper Files +----------------------------------------------- + +For the device level files, look in + + /sys/bus/pci/drivers/ipw2200/{PCI-ID}/ + +For example: + /sys/bus/pci/drivers/ipw2200/0000:02:01.0 + +For the device level files, see /sys/bus/pci/[drivers/ipw2200: + + rf_kill + read - + 0 = RF kill not enabled (radio on) + 1 = SW based RF kill active (radio off) + 2 = HW based RF kill active (radio off) + 3 = Both HW and SW RF kill active (radio off) + write - + 0 = If SW based RF kill active, turn the radio back on + 1 = If radio is on, activate SW based RF kill + + NOTE: If you enable the SW based RF kill and then toggle the HW + based RF kill from ON -> OFF -> ON, the radio will NOT come back on + + ucode + read-only access to the ucode version number + + +2. About the Version Numbers +----------------------------------------------- + +Due to the nature of open source development projects, there are +frequently changes being incorporated that have not gone through +a complete validation process. These changes are incorporated into +development snapshot releases. + +Releases are numbered with a three level scheme: + + major.minor.development + +Any version where the 'development' portion is 0 (for example +1.0.0, 1.1.0, etc.) indicates a stable version that will be made +available for kernel inclusion. + +Any version where the 'development' portion is not a 0 (for +example 1.0.1, 1.1.5, etc.) indicates a development version that is +being made available for testing and cutting edge users. The stability +and functionality of the development releases are not know. We make +efforts to try and keep all snapshots reasonably stable, but due to the +frequency of their release, and the desire to get those releases +available as quickly as possible, unknown anomalies should be expected. + +The major version number will be incremented when significant changes +are made to the driver. Currently, there are no major changes planned. + + +3. Support +----------------------------------------------- + +For installation support of the 1.0.0 version, you can contact +http://supportmail.intel.com, or you can use the open source project +support. + +For general information and support, go to: + + http://ipw2200.sf.net/ + + +4. License +----------------------------------------------- + + Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of the GNU General Public License version 2 as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + + diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig index a60866d62ec7..6e88d4839971 100644 --- a/drivers/net/wireless/Kconfig +++ b/drivers/net/wireless/Kconfig @@ -137,6 +137,111 @@ config PCMCIA_RAYCS comment "Wireless 802.11b ISA/PCI cards support" depends on NET_RADIO && (ISA || PCI || PPC_PMAC || PCMCIA) +config IPW2100 + tristate "Intel PRO/Wireless 2100 Network Connection" + depends on NET_RADIO && PCI && IEEE80211 + select FW_LOADER + ---help--- + A driver for the Intel PRO/Wireless 2100 Network + Connection 802.11b wireless network adapter. + + See <file:Documentation/networking/README.ipw2100> for information on + the capabilities currently enabled in this driver and for tips + for debugging issues and problems. + + In order to use this driver, you will need a firmware image for it. + You can obtain the firmware from + <http://ipw2100.sf.net/>. Once you have the firmware image, you + will need to place it in /etc/firmware. + + You will also very likely need the Wireless Tools in order to + configure your card: + + <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>. + + If you want to compile the driver as a module ( = code which can be + inserted in and remvoed from the running kernel whenever you want), + say M here and read <file:Documentation/modules.txt>. The module + will be called ipw2100.ko. + +config IPW2100_PROMISC + bool "Enable promiscuous mode" + depends on IPW2100 + ---help--- + Enables promiscuous/monitor mode support for the ipw2100 driver. + With this feature compiled into the driver, you can switch to + promiscuous mode via the Wireless Tool's Monitor mode. While in this + mode, no packets can be sent. + +config IPW_DEBUG + bool "Enable full debugging output in IPW2100 module." + depends on IPW2100 + ---help--- + This option will enable debug tracing output for the IPW2100. + + This will result in the kernel module being ~60k larger. You can + control which debug output is sent to the kernel log by setting the + value in + + /sys/bus/pci/drivers/ipw2100/debug_level + + This entry will only exist if this option is enabled. + + If you are not trying to debug or develop the IPW2100 driver, you + most likely want to say N here. + +config IPW2200 + tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection" + depends on NET_RADIO && PCI + select FW_LOADER + select IEEE80211 + ---help--- + A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network + Connection adapters. + + See <file:Documentation/networking/README.ipw2200> for + information on the capabilities currently enabled in this + driver and for tips for debugging issues and problems. + + In order to use this driver, you will need a firmware image for it. + You can obtain the firmware from + <http://ipw2200.sf.net/>. See the above referenced README.ipw2200 + for information on where to install the firmare images. + + You will also very likely need the Wireless Tools in order to + configure your card: + + <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>. + + If you want to compile the driver as a module ( = code which can be + inserted in and remvoed from the running kernel whenever you want), + say M here and read <file:Documentation/modules.txt>. The module + will be called ipw2200.ko. + +config IPW_DEBUG + bool "Enable full debugging output in IPW2200 module." + depends on IPW2200 + ---help--- + This option will enable debug tracing output for the IPW2200. + + This will result in the kernel module being ~100k larger. You can + control which debug output is sent to the kernel log by setting the + value in + + /sys/bus/pci/drivers/ipw2200/debug_level + + This entry will only exist if this option is enabled. + + To set a value, simply echo an 8-byte hex value to the same file: + + % echo 0x00000FFO > /sys/bus/pci/drivers/ipw2200/debug_level + + You can find the list of debug mask values in + drivers/net/wireless/ipw2200.h + + If you are not trying to debug or develop the IPW2200 driver, you + most likely want to say N here. + config AIRO tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards" depends on NET_RADIO && ISA && (PCI || BROKEN) diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile index 6c9cb0eb8581..0953cc0cdee6 100644 --- a/drivers/net/wireless/Makefile +++ b/drivers/net/wireless/Makefile @@ -2,6 +2,10 @@ # Makefile for the Linux Wireless network device drivers. # +obj-$(CONFIG_IPW2100) += ipw2100.o + +obj-$(CONFIG_IPW2200) += ipw2200.o + obj-$(CONFIG_STRIP) += strip.o obj-$(CONFIG_ARLAN) += arlan.o diff --git a/drivers/net/wireless/atmel.c b/drivers/net/wireless/atmel.c index 18a7d38d2a13..bed160a25cab 100644 --- a/drivers/net/wireless/atmel.c +++ b/drivers/net/wireless/atmel.c @@ -68,7 +68,7 @@ #include <linux/device.h> #include <linux/moduleparam.h> #include <linux/firmware.h> -#include "ieee802_11.h" +#include <net/ieee80211.h> #include "atmel.h" #define DRIVER_MAJOR 0 @@ -618,12 +618,12 @@ static int atmel_lock_mac(struct atmel_private *priv); static void atmel_wmem32(struct atmel_private *priv, u16 pos, u32 data); static void atmel_command_irq(struct atmel_private *priv); static int atmel_validate_channel(struct atmel_private *priv, int channel); -static void atmel_management_frame(struct atmel_private *priv, struct ieee802_11_hdr *header, +static void atmel_management_frame(struct atmel_private *priv, struct ieee80211_hdr *header, u16 frame_len, u8 rssi); static void atmel_management_timer(u_long a); static void atmel_send_command(struct atmel_private *priv, int command, void *cmd, int cmd_size); static int atmel_send_command_wait(struct atmel_private *priv, int command, void *cmd, int cmd_size); -static void atmel_transmit_management_frame(struct atmel_private *priv, struct ieee802_11_hdr *header, +static void atmel_transmit_management_frame(struct atmel_private *priv, struct ieee80211_hdr *header, u8 *body, int body_len); static u8 atmel_get_mib8(struct atmel_private *priv, u8 type, u8 index); @@ -827,7 +827,7 @@ static void tx_update_descriptor(struct atmel_private *priv, int is_bcast, u16 l static int start_tx (struct sk_buff *skb, struct net_device *dev) { struct atmel_private *priv = netdev_priv(dev); - struct ieee802_11_hdr header; + struct ieee80211_hdr header; unsigned long flags; u16 buff, frame_ctl, len = (ETH_ZLEN < skb->len) ? skb->len : ETH_ZLEN; u8 SNAP_RFC1024[6] = {0xaa, 0xaa, 0x03, 0x00, 0x00, 0x00}; @@ -863,17 +863,17 @@ static int start_tx (struct sk_buff *skb, struct net_device *dev) return 1; } - frame_ctl = IEEE802_11_FTYPE_DATA; + frame_ctl = IEEE80211_FTYPE_DATA; header.duration_id = 0; header.seq_ctl = 0; if (priv->wep_is_on) - frame_ctl |= IEEE802_11_FCTL_WEP; + frame_ctl |= IEEE80211_FCTL_WEP; if (priv->operating_mode == IW_MODE_ADHOC) { memcpy(&header.addr1, skb->data, 6); memcpy(&header.addr2, dev->dev_addr, 6); memcpy(&header.addr3, priv->BSSID, 6); } else { - frame_ctl |= IEEE802_11_FCTL_TODS; + frame_ctl |= IEEE80211_FCTL_TODS; memcpy(&header.addr1, priv->CurrentBSSID, 6); memcpy(&header.addr2, dev->dev_addr, 6); memcpy(&header.addr3, skb->data, 6); @@ -902,7 +902,7 @@ static int start_tx (struct sk_buff *skb, struct net_device *dev) } static void atmel_transmit_management_frame(struct atmel_private *priv, - struct ieee802_11_hdr *header, + struct ieee80211_hdr *header, u8 *body, int body_len) { u16 buff; @@ -917,7 +917,7 @@ static void atmel_transmit_management_frame(struct atmel_private *priv, tx_update_descriptor(priv, header->addr1[0] & 0x01, len, buff, TX_PACKET_TYPE_MGMT); } -static void fast_rx_path(struct atmel_private *priv, struct ieee802_11_hdr *header, +static void fast_rx_path(struct atmel_private *priv, struct ieee80211_hdr *header, u16 msdu_size, u16 rx_packet_loc, u32 crc) { /* fast path: unfragmented packet copy directly into skbuf */ @@ -955,7 +955,7 @@ static void fast_rx_path(struct atmel_private *priv, struct ieee802_11_hdr *head } memcpy(skbp, header->addr1, 6); /* destination address */ - if (le16_to_cpu(header->frame_ctl) & IEEE802_11_FCTL_FROMDS) + if (le16_to_cpu(header->frame_ctl) & IEEE80211_FCTL_FROMDS) memcpy(&skbp[6], header->addr3, 6); else memcpy(&skbp[6], header->addr2, 6); /* source address */ @@ -990,14 +990,14 @@ static int probe_crc(struct atmel_private *priv, u16 packet_loc, u16 msdu_size) return (crc ^ 0xffffffff) == netcrc; } -static void frag_rx_path(struct atmel_private *priv, struct ieee802_11_hdr *header, +static void frag_rx_path(struct atmel_private *priv, struct ieee80211_hdr *header, u16 msdu_size, u16 rx_packet_loc, u32 crc, u16 seq_no, u8 frag_no, int more_frags) { u8 mac4[6]; u8 source[6]; struct sk_buff *skb; - if (le16_to_cpu(header->frame_ctl) & IEEE802_11_FCTL_FROMDS) + if (le16_to_cpu(header->frame_ctl) & IEEE80211_FCTL_FROMDS) memcpy(source, header->addr3, 6); else memcpy(source, header->addr2, 6); @@ -1082,7 +1082,7 @@ static void frag_rx_path(struct atmel_private *priv, struct ieee802_11_hdr *head static void rx_done_irq(struct atmel_private *priv) { int i; - struct ieee802_11_hdr header; + struct ieee80211_hdr header; for (i = 0; atmel_rmem8(priv, atmel_rx(priv, RX_DESC_FLAGS_OFFSET, priv->rx_desc_head)) == RX_DESC_FLAG_VALID && @@ -1117,7 +1117,7 @@ static void rx_done_irq(struct atmel_private *priv) /* probe for CRC use here if needed once five packets have arrived with the same crc status, we assume we know what's happening and stop probing */ if (priv->probe_crc) { - if (!priv->wep_is_on || !(frame_ctl & IEEE802_11_FCTL_WEP)) { + if (!priv->wep_is_on || !(frame_ctl & IEEE80211_FCTL_WEP)) { priv->do_rx_crc = probe_crc(priv, rx_packet_loc, msdu_size); } else { priv->do_rx_crc = probe_crc(priv, rx_packet_loc + 24, msdu_size - 24); @@ -1132,16 +1132,16 @@ static void rx_done_irq(struct atmel_private *priv) } /* don't CRC header when WEP in use */ - if (priv->do_rx_crc && (!priv->wep_is_on || !(frame_ctl & IEEE802_11_FCTL_WEP))) { + if (priv->do_rx_crc && (!priv->wep_is_on || !(frame_ctl & IEEE80211_FCTL_WEP))) { crc = crc32_le(0xffffffff, (unsigned char *)&header, 24); } msdu_size -= 24; /* header */ - if ((frame_ctl & IEEE802_11_FCTL_FTYPE) == IEEE802_11_FTYPE_DATA) { + if ((frame_ctl & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_DATA) { - int more_fragments = frame_ctl & IEEE802_11_FCTL_MOREFRAGS; - u8 packet_fragment_no = seq_control & IEEE802_11_SCTL_FRAG; - u16 packet_sequence_no = (seq_control & IEEE802_11_SCTL_SEQ) >> 4; + int more_fragments = frame_ctl & IEEE80211_FCTL_MOREFRAGS; + u8 packet_fragment_no = seq_control & IEEE80211_SCTL_FRAG; + u16 packet_sequence_no = (seq_control & IEEE80211_SCTL_SEQ) >> 4; if (!more_fragments && packet_fragment_no == 0 ) { fast_rx_path(priv, &header, msdu_size, rx_packet_loc, crc); @@ -1151,7 +1151,7 @@ static void rx_done_irq(struct atmel_private *priv) } } - if ((frame_ctl & IEEE802_11_FCTL_FTYPE) == IEEE802_11_FTYPE_MGMT) { + if ((frame_ctl & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT) { /* copy rest of packet into buffer */ atmel_copy_to_host(priv->dev, (unsigned char *)&priv->rx_buf, rx_packet_loc + 24, msdu_size); @@ -2663,10 +2663,10 @@ static void handle_beacon_probe(struct atmel_private *priv, u16 capability, u8 c static void send_authentication_request(struct atmel_private *priv, u8 *challenge, int challenge_len) { - struct ieee802_11_hdr header; + struct ieee80211_hdr header; struct auth_body auth; - header.frame_ctl = cpu_to_le16(IEEE802_11_FTYPE_MGMT | IEEE802_11_STYPE_AUTH); + header.frame_ctl = cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_AUTH); header.duration_id = cpu_to_le16(0x8000); header.seq_ctl = 0; memcpy(header.addr1, priv->CurrentBSSID, 6); @@ -2677,7 +2677,7 @@ static void send_authentication_request(struct atmel_private *priv, u8 *challeng auth.alg = cpu_to_le16(C80211_MGMT_AAN_SHAREDKEY); /* no WEP for authentication frames with TrSeqNo 1 */ if (priv->CurrentAuthentTransactionSeqNum != 1) - header.frame_ctl |= cpu_to_le16(IEEE802_11_FCTL_WEP); + header.frame_ctl |= cpu_to_le16(IEEE80211_FCTL_WEP); } else { auth.alg = cpu_to_le16(C80211_MGMT_AAN_OPENSYSTEM); } @@ -2701,7 +2701,7 @@ static void send_association_request(struct atmel_private *priv, int is_reassoc) { u8 *ssid_el_p; int bodysize; - struct ieee802_11_hdr header; + struct ieee80211_hdr header; struct ass_req_format { u16 capability; u16 listen_interval; @@ -2714,8 +2714,8 @@ static void send_association_request(struct atmel_private *priv, int is_reassoc) u8 rates[4]; } body; - header.frame_ctl = cpu_to_le16(IEEE802_11_FTYPE_MGMT | - (is_reassoc ? IEEE802_11_STYPE_REASSOC_REQ : IEEE802_11_STYPE_ASSOC_REQ)); + header.frame_ctl = cpu_to_le16(IEEE80211_FTYPE_MGMT | + (is_reassoc ? IEEE80211_STYPE_REASSOC_REQ : IEEE80211_STYPE_ASSOC_REQ)); header.duration_id = cpu_to_le16(0x8000); header.seq_ctl = 0; @@ -2751,9 +2751,9 @@ static void send_association_request(struct atmel_private *priv, int is_reassoc) atmel_transmit_management_frame(priv, &header, (void *)&body, bodysize); } -static int is_frame_from_current_bss(struct atmel_private *priv, struct ieee802_11_hdr *header) +static int is_frame_from_current_bss(struct atmel_private *priv, struct ieee80211_hdr *header) { - if (le16_to_cpu(header->frame_ctl) & IEEE802_11_FCTL_FROMDS) + if (le16_to_cpu(header->frame_ctl) & IEEE80211_FCTL_FROMDS) return memcmp(header->addr3, priv->CurrentBSSID, 6) == 0; else return memcmp(header->addr2, priv->CurrentBSSID, 6) == 0; @@ -2801,7 +2801,7 @@ static int retrieve_bss(struct atmel_private *priv) } -static void store_bss_info(struct atmel_private *priv, struct ieee802_11_hdr *header, +static void store_bss_info(struct atmel_private *priv, struct ieee80211_hdr *header, u16 capability, u16 beacon_period, u8 channel, u8 rssi, u8 ssid_len, u8 *ssid, int is_beacon) { @@ -3085,12 +3085,12 @@ static void atmel_smooth_qual(struct atmel_private *priv) } /* deals with incoming managment frames. */ -static void atmel_management_frame(struct atmel_private *priv, struct ieee802_11_hdr *header, +static void atmel_management_frame(struct atmel_private *priv, struct ieee80211_hdr *header, u16 frame_len, u8 rssi) { u16 subtype; - switch (subtype = le16_to_cpu(header->frame_ctl) & IEEE802_11_FCTL_STYPE) { + switch (subtype = le16_to_cpu(header->frame_ctl) & IEEE80211_FCTL_STYPE) { case C80211_SUBTYPE_MGMT_BEACON : case C80211_SUBTYPE_MGMT_ProbeResponse: diff --git a/drivers/net/wireless/ieee802_11.h b/drivers/net/wireless/ieee802_11.h deleted file mode 100644 index 53dd5248f9f1..000000000000 --- a/drivers/net/wireless/ieee802_11.h +++ /dev/null @@ -1,78 +0,0 @@ -#ifndef _IEEE802_11_H -#define _IEEE802_11_H - -#define IEEE802_11_DATA_LEN 2304 -/* Maximum size for the MA-UNITDATA primitive, 802.11 standard section - 6.2.1.1.2. - - The figure in section 7.1.2 suggests a body size of up to 2312 - bytes is allowed, which is a bit confusing, I suspect this - represents the 2304 bytes of real data, plus a possible 8 bytes of - WEP IV and ICV. (this interpretation suggested by Ramiro Barreiro) */ - - -#define IEEE802_11_HLEN 30 -#define IEEE802_11_FRAME_LEN (IEEE802_11_DATA_LEN + IEEE802_11_HLEN) - -struct ieee802_11_hdr { - u16 frame_ctl; - u16 duration_id; - u8 addr1[ETH_ALEN]; - u8 addr2[ETH_ALEN]; - u8 addr3[ETH_ALEN]; - u16 seq_ctl; - u8 addr4[ETH_ALEN]; -} __attribute__ ((packed)); - -/* Frame control field constants */ -#define IEEE802_11_FCTL_VERS 0x0002 -#define IEEE802_11_FCTL_FTYPE 0x000c -#define IEEE802_11_FCTL_STYPE 0x00f0 -#define IEEE802_11_FCTL_TODS 0x0100 -#define IEEE802_11_FCTL_FROMDS 0x0200 -#define IEEE802_11_FCTL_MOREFRAGS 0x0400 -#define IEEE802_11_FCTL_RETRY 0x0800 -#define IEEE802_11_FCTL_PM 0x1000 -#define IEEE802_11_FCTL_MOREDATA 0x2000 -#define IEEE802_11_FCTL_WEP 0x4000 -#define IEEE802_11_FCTL_ORDER 0x8000 - -#define IEEE802_11_FTYPE_MGMT 0x0000 -#define IEEE802_11_FTYPE_CTL 0x0004 -#define IEEE802_11_FTYPE_DATA 0x0008 - -/* management */ -#define IEEE802_11_STYPE_ASSOC_REQ 0x0000 -#define IEEE802_11_STYPE_ASSOC_RESP 0x0010 -#define IEEE802_11_STYPE_REASSOC_REQ 0x0020 -#define IEEE802_11_STYPE_REASSOC_RESP 0x0030 -#define IEEE802_11_STYPE_PROBE_REQ 0x0040 -#define IEEE802_11_STYPE_PROBE_RESP 0x0050 -#define IEEE802_11_STYPE_BEACON 0x0080 -#define IEEE802_11_STYPE_ATIM 0x0090 -#define IEEE802_11_STYPE_DISASSOC 0x00A0 -#define IEEE802_11_STYPE_AUTH 0x00B0 -#define IEEE802_11_STYPE_DEAUTH 0x00C0 - -/* control */ -#define IEEE802_11_STYPE_PSPOLL 0x00A0 -#define IEEE802_11_STYPE_RTS 0x00B0 -#define IEEE802_11_STYPE_CTS 0x00C0 -#define IEEE802_11_STYPE_ACK 0x00D0 -#define IEEE802_11_STYPE_CFEND 0x00E0 -#define IEEE802_11_STYPE_CFENDACK 0x00F0 - -/* data */ -#define IEEE802_11_STYPE_DATA 0x0000 -#define IEEE802_11_STYPE_DATA_CFACK 0x0010 -#define IEEE802_11_STYPE_DATA_CFPOLL 0x0020 -#define IEEE802_11_STYPE_DATA_CFACKPOLL 0x0030 -#define IEEE802_11_STYPE_NULLFUNC 0x0040 -#define IEEE802_11_STYPE_CFACK 0x0050 -#define IEEE802_11_STYPE_CFPOLL 0x0060 -#define IEEE802_11_STYPE_CFACKPOLL 0x0070 - -#define IEEE802_11_SCTL_FRAG 0x000F -#define IEEE802_11_SCTL_SEQ 0xFFF0 - -#endif /* _IEEE802_11_H */ diff --git a/drivers/net/wireless/ipw2100.c b/drivers/net/wireless/ipw2100.c new file mode 100644 index 000000000000..d296d464946f --- /dev/null +++ b/drivers/net/wireless/ipw2100.c @@ -0,0 +1,8649 @@ +/****************************************************************************** + + Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + + Portions of this file are based on the sample_* files provided by Wireless + Extensions 0.26 package and copyright (c) 1997-2003 Jean Tourrilhes + <jt@hpl.hp.com> + + Portions of this file are based on the Host AP project, + Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + <jkmaline@cc.hut.fi> + Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + + Portions of ipw2100_mod_firmware_load, ipw2100_do_mod_firmware_load, and + ipw2100_fw_load are loosely based on drivers/sound/sound_firmware.c + available in the 2.4.25 kernel sources, and are copyright (c) Alan Cox + +******************************************************************************/ +/* + + Initial driver on which this is based was developed by Janusz Gorycki, + Maciej Urbaniak, and Maciej Sosnowski. + + Promiscuous mode support added by Jacek Wysoczynski and Maciej Urbaniak. + +Theory of Operation + +Tx - Commands and Data + +Firmware and host share a circular queue of Transmit Buffer Descriptors (TBDs) +Each TBD contains a pointer to the physical (dma_addr_t) address of data being +sent to the firmware as well as the length of the data. + +The host writes to the TBD queue at the WRITE index. The WRITE index points +to the _next_ packet to be written and is advanced when after the TBD has been +filled. + +The firmware pulls from the TBD queue at the READ index. The READ index points +to the currently being read entry, and is advanced once the firmware is +done with a packet. + +When data is sent to the firmware, the first TBD is used to indicate to the +firmware if a Command or Data is being sent. If it is Command, all of the +command information is contained within the physical address referred to by the +TBD. If it is Data, the first TBD indicates the type of data packet, number +of fragments, etc. The next TBD then referrs to the actual packet location. + +The Tx flow cycle is as follows: + +1) ipw2100_tx() is called by kernel with SKB to transmit +2) Packet is move from the tx_free_list and appended to the transmit pending + list (tx_pend_list) +3) work is scheduled to move pending packets into the shared circular queue. +4) when placing packet in the circular queue, the incoming SKB is DMA mapped + to a physical address. That address is entered into a TBD. Two TBDs are + filled out. The first indicating a data packet, the second referring to the + actual payload data. +5) the packet is removed from tx_pend_list and placed on the end of the + firmware pending list (fw_pend_list) +6) firmware is notified that the WRITE index has +7) Once the firmware has processed the TBD, INTA is triggered. +8) For each Tx interrupt received from the firmware, the READ index is checked + to see which TBDs are done being processed. +9) For each TBD that has been processed, the ISR pulls the oldest packet + from the fw_pend_list. +10)The packet structure contained in the fw_pend_list is then used + to unmap the DMA address and to free the SKB originally passed to the driver + from the kernel. +11)The packet structure is placed onto the tx_free_list + +The above steps are the same for commands, only the msg_free_list/msg_pend_list +are used instead of tx_free_list/tx_pend_list + +... + +Critical Sections / Locking : + +There are two locks utilized. The first is the low level lock (priv->low_lock) +that protects the following: + +- Access to the Tx/Rx queue lists via priv->low_lock. The lists are as follows: + + tx_free_list : Holds pre-allocated Tx buffers. + TAIL modified in __ipw2100_tx_process() + HEAD modified in ipw2100_tx() + + tx_pend_list : Holds used Tx buffers waiting to go into the TBD ring + TAIL modified ipw2100_tx() + HEAD modified by X__ipw2100_tx_send_data() + + msg_free_list : Holds pre-allocated Msg (Command) buffers + TAIL modified in __ipw2100_tx_process() + HEAD modified in ipw2100_hw_send_command() + + msg_pend_list : Holds used Msg buffers waiting to go into the TBD ring + TAIL modified in ipw2100_hw_send_command() + HEAD modified in X__ipw2100_tx_send_commands() + + The flow of data on the TX side is as follows: + + MSG_FREE_LIST + COMMAND => MSG_PEND_LIST => TBD => MSG_FREE_LIST + TX_FREE_LIST + DATA => TX_PEND_LIST => TBD => TX_FREE_LIST + + The methods that work on the TBD ring are protected via priv->low_lock. + +- The internal data state of the device itself +- Access to the firmware read/write indexes for the BD queues + and associated logic + +All external entry functions are locked with the priv->action_lock to ensure +that only one external action is invoked at a time. + + +*/ + +#include <linux/compiler.h> +#include <linux/config.h> +#include <linux/errno.h> +#include <linux/if_arp.h> +#include <linux/in6.h> +#include <linux/in.h> +#include <linux/ip.h> +#include <linux/kernel.h> +#include <linux/kmod.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/ethtool.h> +#include <linux/pci.h> +#include <linux/proc_fs.h> +#include <linux/skbuff.h> +#include <asm/uaccess.h> +#include <asm/io.h> +#define __KERNEL_SYSCALLS__ +#include <linux/fs.h> +#include <linux/mm.h> +#include <linux/slab.h> +#include <linux/unistd.h> +#include <linux/stringify.h> +#include <linux/tcp.h> +#include <linux/types.h> +#include <linux/version.h> +#include <linux/time.h> +#include <linux/firmware.h> +#include <linux/acpi.h> +#include <linux/ctype.h> + +#include "ipw2100.h" + +#define IPW2100_VERSION "1.1.0" + +#define DRV_NAME "ipw2100" +#define DRV_VERSION IPW2100_VERSION +#define DRV_DESCRIPTION "Intel(R) PRO/Wireless 2100 Network Driver" +#define DRV_COPYRIGHT "Copyright(c) 2003-2004 Intel Corporation" + + +/* Debugging stuff */ +#ifdef CONFIG_IPW_DEBUG +#define CONFIG_IPW2100_RX_DEBUG /* Reception debugging */ +#endif + +MODULE_DESCRIPTION(DRV_DESCRIPTION); +MODULE_VERSION(DRV_VERSION); +MODULE_AUTHOR(DRV_COPYRIGHT); +MODULE_LICENSE("GPL"); + +static int debug = 0; +static int mode = 0; +static int channel = 0; +static int associate = 1; +static int disable = 0; +#ifdef CONFIG_PM +static struct ipw2100_fw ipw2100_firmware; +#endif + +#include <linux/moduleparam.h> +module_param(debug, int, 0444); +module_param(mode, int, 0444); +module_param(channel, int, 0444); +module_param(associate, int, 0444); +module_param(disable, int, 0444); + +MODULE_PARM_DESC(debug, "debug level"); +MODULE_PARM_DESC(mode, "network mode (0=BSS,1=IBSS,2=Monitor)"); +MODULE_PARM_DESC(channel, "channel"); +MODULE_PARM_DESC(associate, "auto associate when scanning (default on)"); +MODULE_PARM_DESC(disable, "manually disable the radio (default 0 [radio on])"); + +u32 ipw2100_debug_level = IPW_DL_NONE; + +#ifdef CONFIG_IPW_DEBUG +static const char *command_types[] = { + "undefined", + "unused", /* HOST_ATTENTION */ + "HOST_COMPLETE", + "unused", /* SLEEP */ + "unused", /* HOST_POWER_DOWN */ + "unused", + "SYSTEM_CONFIG", + "unused", /* SET_IMR */ + "SSID", + "MANDATORY_BSSID", + "AUTHENTICATION_TYPE", + "ADAPTER_ADDRESS", + "PORT_TYPE", + "INTERNATIONAL_MODE", + "CHANNEL", + "RTS_THRESHOLD", + "FRAG_THRESHOLD", + "POWER_MODE", + "TX_RATES", + "BASIC_TX_RATES", + "WEP_KEY_INFO", + "unused", + "unused", + "unused", + "unused", + "WEP_KEY_INDEX", + "WEP_FLAGS", + "ADD_MULTICAST", + "CLEAR_ALL_MULTICAST", + "BEACON_INTERVAL", + "ATIM_WINDOW", + "CLEAR_STATISTICS", + "undefined", + "undefined", + "undefined", + "undefined", + "TX_POWER_INDEX", + "undefined", + "undefined", + "undefined", + "undefined", + "undefined", + "undefined", + "BROADCAST_SCAN", + "CARD_DISABLE", + "PREFERRED_BSSID", + "SET_SCAN_OPTIONS", + "SCAN_DWELL_TIME", + "SWEEP_TABLE", + "AP_OR_STATION_TABLE", + "GROUP_ORDINALS", + "SHORT_RETRY_LIMIT", + "LONG_RETRY_LIMIT", + "unused", /* SAVE_CALIBRATION */ + "unused", /* RESTORE_CALIBRATION */ + "undefined", + "undefined", + "undefined", + "HOST_PRE_POWER_DOWN", + "unused", /* HOST_INTERRUPT_COALESCING */ + "undefined", + "CARD_DISABLE_PHY_OFF", + "MSDU_TX_RATES" + "undefined", + "undefined", + "SET_STATION_STAT_BITS", + "CLEAR_STATIONS_STAT_BITS", + "LEAP_ROGUE_MODE", + "SET_SECURITY_INFORMATION", + "DISASSOCIATION_BSSID", + "SET_WPA_ASS_IE" +}; +#endif + + +/* Pre-decl until we get the code solid and then we can clean it up */ +static void X__ipw2100_tx_send_commands(struct ipw2100_priv *priv); +static void X__ipw2100_tx_send_data(struct ipw2100_priv *priv); +static int ipw2100_adapter_setup(struct ipw2100_priv *priv); + +static void ipw2100_queues_initialize(struct ipw2100_priv *priv); +static void ipw2100_queues_free(struct ipw2100_priv *priv); +static int ipw2100_queues_allocate(struct ipw2100_priv *priv); + + +static inline void read_register(struct net_device *dev, u32 reg, u32 *val) +{ + *val = readl((void *)(dev->base_addr + reg)); + IPW_DEBUG_IO("r: 0x%08X => 0x%08X\n", reg, *val); +} + +static inline void write_register(struct net_device *dev, u32 reg, u32 val) +{ + writel(val, (void *)(dev->base_addr + reg)); + IPW_DEBUG_IO("w: 0x%08X <= 0x%08X\n", reg, val); +} + +static inline void read_register_word(struct net_device *dev, u32 reg, u16 *val) +{ + *val = readw((void *)(dev->base_addr + reg)); + IPW_DEBUG_IO("r: 0x%08X => %04X\n", reg, *val); +} + +static inline void read_register_byte(struct net_device *dev, u32 reg, u8 *val) +{ + *val = readb((void *)(dev->base_addr + reg)); + IPW_DEBUG_IO("r: 0x%08X => %02X\n", reg, *val); +} + +static inline void write_register_word(struct net_device *dev, u32 reg, u16 val) +{ + writew(val, (void *)(dev->base_addr + reg)); + IPW_DEBUG_IO("w: 0x%08X <= %04X\n", reg, val); +} + + +static inline void write_register_byte(struct net_device *dev, u32 reg, u8 val) +{ + writeb(val, (void *)(dev->base_addr + reg)); + IPW_DEBUG_IO("w: 0x%08X =< %02X\n", reg, val); +} + +static inline void read_nic_dword(struct net_device *dev, u32 addr, u32 *val) +{ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); + read_register(dev, IPW_REG_INDIRECT_ACCESS_DATA, val); +} + +static inline void write_nic_dword(struct net_device *dev, u32 addr, u32 val) +{ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); + write_register(dev, IPW_REG_INDIRECT_ACCESS_DATA, val); +} + +static inline void read_nic_word(struct net_device *dev, u32 addr, u16 *val) +{ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); + read_register_word(dev, IPW_REG_INDIRECT_ACCESS_DATA, val); +} + +static inline void write_nic_word(struct net_device *dev, u32 addr, u16 val) +{ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); + write_register_word(dev, IPW_REG_INDIRECT_ACCESS_DATA, val); +} + +static inline void read_nic_byte(struct net_device *dev, u32 addr, u8 *val) +{ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); + read_register_byte(dev, IPW_REG_INDIRECT_ACCESS_DATA, val); +} + +static inline void write_nic_byte(struct net_device *dev, u32 addr, u8 val) +{ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); + write_register_byte(dev, IPW_REG_INDIRECT_ACCESS_DATA, val); +} + +static inline void write_nic_auto_inc_address(struct net_device *dev, u32 addr) +{ + write_register(dev, IPW_REG_AUTOINCREMENT_ADDRESS, + addr & IPW_REG_INDIRECT_ADDR_MASK); +} + +static inline void write_nic_dword_auto_inc(struct net_device *dev, u32 val) +{ + write_register(dev, IPW_REG_AUTOINCREMENT_DATA, val); +} + +static inline void write_nic_memory(struct net_device *dev, u32 addr, u32 len, + const u8 *buf) +{ + u32 aligned_addr; + u32 aligned_len; + u32 dif_len; + u32 i; + + /* read first nibble byte by byte */ + aligned_addr = addr & (~0x3); + dif_len = addr - aligned_addr; + if (dif_len) { + /* Start reading at aligned_addr + dif_len */ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + aligned_addr); + for (i = dif_len; i < 4; i++, buf++) + write_register_byte( + dev, IPW_REG_INDIRECT_ACCESS_DATA + i, + *buf); + + len -= dif_len; + aligned_addr += 4; + } + + /* read DWs through autoincrement registers */ + write_register(dev, IPW_REG_AUTOINCREMENT_ADDRESS, + aligned_addr); + aligned_len = len & (~0x3); + for (i = 0; i < aligned_len; i += 4, buf += 4, aligned_addr += 4) + write_register( + dev, IPW_REG_AUTOINCREMENT_DATA, *(u32 *)buf); + + /* copy the last nibble */ + dif_len = len - aligned_len; + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, aligned_addr); + for (i = 0; i < dif_len; i++, buf++) + write_register_byte( + dev, IPW_REG_INDIRECT_ACCESS_DATA + i, *buf); +} + +static inline void read_nic_memory(struct net_device *dev, u32 addr, u32 len, + u8 *buf) +{ + u32 aligned_addr; + u32 aligned_len; + u32 dif_len; + u32 i; + + /* read first nibble byte by byte */ + aligned_addr = addr & (~0x3); + dif_len = addr - aligned_addr; + if (dif_len) { + /* Start reading at aligned_addr + dif_len */ + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + aligned_addr); + for (i = dif_len; i < 4; i++, buf++) + read_register_byte( + dev, IPW_REG_INDIRECT_ACCESS_DATA + i, buf); + + len -= dif_len; + aligned_addr += 4; + } + + /* read DWs through autoincrement registers */ + write_register(dev, IPW_REG_AUTOINCREMENT_ADDRESS, + aligned_addr); + aligned_len = len & (~0x3); + for (i = 0; i < aligned_len; i += 4, buf += 4, aligned_addr += 4) + read_register(dev, IPW_REG_AUTOINCREMENT_DATA, + (u32 *)buf); + + /* copy the last nibble */ + dif_len = len - aligned_len; + write_register(dev, IPW_REG_INDIRECT_ACCESS_ADDRESS, + aligned_addr); + for (i = 0; i < dif_len; i++, buf++) + read_register_byte(dev, IPW_REG_INDIRECT_ACCESS_DATA + + i, buf); +} + +static inline int ipw2100_hw_is_adapter_in_system(struct net_device *dev) +{ + return (dev->base_addr && + (readl((void *)(dev->base_addr + IPW_REG_DOA_DEBUG_AREA_START)) + == IPW_DATA_DOA_DEBUG_VALUE)); +} + +int ipw2100_get_ordinal(struct ipw2100_priv *priv, u32 ord, + void *val, u32 *len) +{ + struct ipw2100_ordinals *ordinals = &priv->ordinals; + u32 addr; + u32 field_info; + u16 field_len; + u16 field_count; + u32 total_length; + + if (ordinals->table1_addr == 0) { + IPW_DEBUG_WARNING(DRV_NAME ": attempt to use fw ordinals " + "before they have been loaded.\n"); + return -EINVAL; + } + + if (IS_ORDINAL_TABLE_ONE(ordinals, ord)) { + if (*len < IPW_ORD_TAB_1_ENTRY_SIZE) { + *len = IPW_ORD_TAB_1_ENTRY_SIZE; + + IPW_DEBUG_WARNING(DRV_NAME + ": ordinal buffer length too small, need %d\n", + IPW_ORD_TAB_1_ENTRY_SIZE); + + return -EINVAL; + } + + read_nic_dword(priv->net_dev, ordinals->table1_addr + (ord << 2), + &addr); + read_nic_dword(priv->net_dev, addr, val); + + *len = IPW_ORD_TAB_1_ENTRY_SIZE; + + return 0; + } + + if (IS_ORDINAL_TABLE_TWO(ordinals, ord)) { + + ord -= IPW_START_ORD_TAB_2; + + /* get the address of statistic */ + read_nic_dword(priv->net_dev, ordinals->table2_addr + (ord << 3), + &addr); + + /* get the second DW of statistics ; + * two 16-bit words - first is length, second is count */ + read_nic_dword(priv->net_dev, + ordinals->table2_addr + (ord << 3) + sizeof(u32), + &field_info); + + /* get each entry length */ + field_len = *((u16 *)&field_info); + + /* get number of entries */ + field_count = *(((u16 *)&field_info) + 1); + + /* abort if no enought memory */ + total_length = field_len * field_count; + if (total_length > *len) { + *len = total_length; + return -EINVAL; + } + + *len = total_length; + if (!total_length) + return 0; + + /* read the ordinal data from the SRAM */ + read_nic_memory(priv->net_dev, addr, total_length, val); + + return 0; + } + + IPW_DEBUG_WARNING(DRV_NAME ": ordinal %d neither in table 1 nor " + "in table 2\n", ord); + + return -EINVAL; +} + +static int ipw2100_set_ordinal(struct ipw2100_priv *priv, u32 ord, u32 *val, + u32 *len) +{ + struct ipw2100_ordinals *ordinals = &priv->ordinals; + u32 addr; + + if (IS_ORDINAL_TABLE_ONE(ordinals, ord)) { + if (*len != IPW_ORD_TAB_1_ENTRY_SIZE) { + *len = IPW_ORD_TAB_1_ENTRY_SIZE; + IPW_DEBUG_INFO("wrong size\n"); + return -EINVAL; + } + + read_nic_dword(priv->net_dev, ordinals->table1_addr + (ord << 2), + &addr); + + write_nic_dword(priv->net_dev, addr, *val); + + *len = IPW_ORD_TAB_1_ENTRY_SIZE; + + return 0; + } + + IPW_DEBUG_INFO("wrong table\n"); + if (IS_ORDINAL_TABLE_TWO(ordinals, ord)) + return -EINVAL; + + return -EINVAL; +} + +static char *snprint_line(char *buf, size_t count, + const u8 *data, u32 len, u32 ofs) +{ + int out, i, j, l; + char c; + + out = snprintf(buf, count, "%08X", ofs); + + for (l = 0, i = 0; i < 2; i++) { + out += snprintf(buf + out, count - out, " "); + for (j = 0; j < 8 && l < len; j++, l++) + out += snprintf(buf + out, count - out, "%02X ", + data[(i * 8 + j)]); + for (; j < 8; j++) + out += snprintf(buf + out, count - out, " "); + } + + out += snprintf(buf + out, count - out, " "); + for (l = 0, i = 0; i < 2; i++) { + out += snprintf(buf + out, count - out, " "); + for (j = 0; j < 8 && l < len; j++, l++) { + c = data[(i * 8 + j)]; + if (!isascii(c) || !isprint(c)) + c = '.'; + + out += snprintf(buf + out, count - out, "%c", c); + } + + for (; j < 8; j++) + out += snprintf(buf + out, count - out, " "); + } + + return buf; +} + +static void printk_buf(int level, const u8 *data, u32 len) +{ + char line[81]; + u32 ofs = 0; + if (!(ipw2100_debug_level & level)) + return; + + while (len) { + printk(KERN_DEBUG "%s\n", + snprint_line(line, sizeof(line), &data[ofs], + min(len, 16U), ofs)); + ofs += 16; + len -= min(len, 16U); + } +} + + + +#define MAX_RESET_BACKOFF 10 + +static inline void schedule_reset(struct ipw2100_priv *priv) +{ + unsigned long now = get_seconds(); + + /* If we haven't received a reset request within the backoff period, + * then we can reset the backoff interval so this reset occurs + * immediately */ + if (priv->reset_backoff && + (now - priv->last_reset > priv->reset_backoff)) + priv->reset_backoff = 0; + + priv->last_reset = get_seconds(); + + if (!(priv->status & STATUS_RESET_PENDING)) { + IPW_DEBUG_INFO("%s: Scheduling firmware restart (%ds).\n", + priv->net_dev->name, priv->reset_backoff); + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); + priv->status |= STATUS_RESET_PENDING; + if (priv->reset_backoff) + queue_delayed_work(priv->workqueue, &priv->reset_work, + priv->reset_backoff * HZ); + else + queue_work(priv->workqueue, &priv->reset_work); + + if (priv->reset_backoff < MAX_RESET_BACKOFF) + priv->reset_backoff++; + + wake_up_interruptible(&priv->wait_command_queue); + } else + IPW_DEBUG_INFO("%s: Firmware restart already in progress.\n", + priv->net_dev->name); + +} + +#define HOST_COMPLETE_TIMEOUT (2 * HZ) +static int ipw2100_hw_send_command(struct ipw2100_priv *priv, + struct host_command * cmd) +{ + struct list_head *element; + struct ipw2100_tx_packet *packet; + unsigned long flags; + int err = 0; + + IPW_DEBUG_HC("Sending %s command (#%d), %d bytes\n", + command_types[cmd->host_command], cmd->host_command, + cmd->host_command_length); + printk_buf(IPW_DL_HC, (u8*)cmd->host_command_parameters, + cmd->host_command_length); + + spin_lock_irqsave(&priv->low_lock, flags); + + if (priv->fatal_error) { + IPW_DEBUG_INFO("Attempt to send command while hardware in fatal error condition.\n"); + err = -EIO; + goto fail_unlock; + } + + if (!(priv->status & STATUS_RUNNING)) { + IPW_DEBUG_INFO("Attempt to send command while hardware is not running.\n"); + err = -EIO; + goto fail_unlock; + } + + if (priv->status & STATUS_CMD_ACTIVE) { + IPW_DEBUG_INFO("Attempt to send command while another command is pending.\n"); + err = -EBUSY; + goto fail_unlock; + } + + if (list_empty(&priv->msg_free_list)) { + IPW_DEBUG_INFO("no available msg buffers\n"); + goto fail_unlock; + } + + priv->status |= STATUS_CMD_ACTIVE; + priv->messages_sent++; + + element = priv->msg_free_list.next; + + packet = list_entry(element, struct ipw2100_tx_packet, list); + packet->jiffy_start = jiffies; + + /* initialize the firmware command packet */ + packet->info.c_struct.cmd->host_command_reg = cmd->host_command; + packet->info.c_struct.cmd->host_command_reg1 = cmd->host_command1; + packet->info.c_struct.cmd->host_command_len_reg = cmd->host_command_length; + packet->info.c_struct.cmd->sequence = cmd->host_command_sequence; + + memcpy(packet->info.c_struct.cmd->host_command_params_reg, + cmd->host_command_parameters, + sizeof(packet->info.c_struct.cmd->host_command_params_reg)); + + list_del(element); + DEC_STAT(&priv->msg_free_stat); + + list_add_tail(element, &priv->msg_pend_list); + INC_STAT(&priv->msg_pend_stat); + + X__ipw2100_tx_send_commands(priv); + X__ipw2100_tx_send_data(priv); + + spin_unlock_irqrestore(&priv->low_lock, flags); + + /* + * We must wait for this command to complete before another + * command can be sent... but if we wait more than 3 seconds + * then there is a problem. + */ + + err = wait_event_interruptible_timeout( + priv->wait_command_queue, !(priv->status & STATUS_CMD_ACTIVE), + HOST_COMPLETE_TIMEOUT); + + if (err == 0) { + IPW_DEBUG_INFO("Command completion failed out after %dms.\n", + HOST_COMPLETE_TIMEOUT / (HZ / 100)); + priv->fatal_error = IPW2100_ERR_MSG_TIMEOUT; + priv->status &= ~STATUS_CMD_ACTIVE; + schedule_reset(priv); + return -EIO; + } + + if (priv->fatal_error) { + IPW_DEBUG_WARNING("%s: firmware fatal error\n", + priv->net_dev->name); + return -EIO; + } + + /* !!!!! HACK TEST !!!!! + * When lots of debug trace statements are enabled, the driver + * doesn't seem to have as many firmware restart cycles... + * + * As a test, we're sticking in a 1/100s delay here */ + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(HZ / 100); + + return 0; + + fail_unlock: + spin_unlock_irqrestore(&priv->low_lock, flags); + + return err; +} + + +/* + * Verify the values and data access of the hardware + * No locks needed or used. No functions called. + */ +static int ipw2100_verify(struct ipw2100_priv *priv) +{ + u32 data1, data2; + u32 address; + + u32 val1 = 0x76543210; + u32 val2 = 0xFEDCBA98; + + /* Domain 0 check - all values should be DOA_DEBUG */ + for (address = IPW_REG_DOA_DEBUG_AREA_START; + address < IPW_REG_DOA_DEBUG_AREA_END; + address += sizeof(u32)) { + read_register(priv->net_dev, address, &data1); + if (data1 != IPW_DATA_DOA_DEBUG_VALUE) + return -EIO; + } + + /* Domain 1 check - use arbitrary read/write compare */ + for (address = 0; address < 5; address++) { + /* The memory area is not used now */ + write_register(priv->net_dev, IPW_REG_DOMAIN_1_OFFSET + 0x32, + val1); + write_register(priv->net_dev, IPW_REG_DOMAIN_1_OFFSET + 0x36, + val2); + read_register(priv->net_dev, IPW_REG_DOMAIN_1_OFFSET + 0x32, + &data1); + read_register(priv->net_dev, IPW_REG_DOMAIN_1_OFFSET + 0x36, + &data2); + if (val1 == data1 && val2 == data2) + return 0; + } + + return -EIO; +} + +/* + * + * Loop until the CARD_DISABLED bit is the same value as the + * supplied parameter + * + * TODO: See if it would be more efficient to do a wait/wake + * cycle and have the completion event trigger the wakeup + * + */ +#define IPW_CARD_DISABLE_COMPLETE_WAIT 100 // 100 milli +static int ipw2100_wait_for_card_state(struct ipw2100_priv *priv, int state) +{ + int i; + u32 card_state; + u32 len = sizeof(card_state); + int err; + + for (i = 0; i <= IPW_CARD_DISABLE_COMPLETE_WAIT * 1000; i += 50) { + err = ipw2100_get_ordinal(priv, IPW_ORD_CARD_DISABLED, + &card_state, &len); + if (err) { + IPW_DEBUG_INFO("Query of CARD_DISABLED ordinal " + "failed.\n"); + return 0; + } + + /* We'll break out if either the HW state says it is + * in the state we want, or if HOST_COMPLETE command + * finishes */ + if ((card_state == state) || + ((priv->status & STATUS_ENABLED) ? + IPW_HW_STATE_ENABLED : IPW_HW_STATE_DISABLED) == state) { + if (state == IPW_HW_STATE_ENABLED) + priv->status |= STATUS_ENABLED; + else + priv->status &= ~STATUS_ENABLED; + + return 0; + } + + udelay(50); + } + + IPW_DEBUG_INFO("ipw2100_wait_for_card_state to %s state timed out\n", + state ? "DISABLED" : "ENABLED"); + return -EIO; +} + + +/********************************************************************* + Procedure : sw_reset_and_clock + Purpose : Asserts s/w reset, asserts clock initialization + and waits for clock stabilization + ********************************************************************/ +static int sw_reset_and_clock(struct ipw2100_priv *priv) +{ + int i; + u32 r; + + // assert s/w reset + write_register(priv->net_dev, IPW_REG_RESET_REG, + IPW_AUX_HOST_RESET_REG_SW_RESET); + + // wait for clock stabilization + for (i = 0; i < 1000; i++) { + udelay(IPW_WAIT_RESET_ARC_COMPLETE_DELAY); + + // check clock ready bit + read_register(priv->net_dev, IPW_REG_RESET_REG, &r); + if (r & IPW_AUX_HOST_RESET_REG_PRINCETON_RESET) + break; + } + + if (i == 1000) + return -EIO; // TODO: better error value + + /* set "initialization complete" bit to move adapter to + * D0 state */ + write_register(priv->net_dev, IPW_REG_GP_CNTRL, + IPW_AUX_HOST_GP_CNTRL_BIT_INIT_DONE); + + /* wait for clock stabilization */ + for (i = 0; i < 10000; i++) { + udelay(IPW_WAIT_CLOCK_STABILIZATION_DELAY * 4); + + /* check clock ready bit */ + read_register(priv->net_dev, IPW_REG_GP_CNTRL, &r); + if (r & IPW_AUX_HOST_GP_CNTRL_BIT_CLOCK_READY) + break; + } + + if (i == 10000) + return -EIO; /* TODO: better error value */ + +//#if CONFIG_IPW2100_D0ENABLED + /* set D0 standby bit */ + read_register(priv->net_dev, IPW_REG_GP_CNTRL, &r); + write_register(priv->net_dev, IPW_REG_GP_CNTRL, + r | IPW_AUX_HOST_GP_CNTRL_BIT_HOST_ALLOWS_STANDBY); +//#endif + + return 0; +} + +/********************************************************************* + Procedure : ipw2100_ipw2100_download_firmware + Purpose : Initiaze adapter after power on. + The sequence is: + 1. assert s/w reset first! + 2. awake clocks & wait for clock stabilization + 3. hold ARC (don't ask me why...) + 4. load Dino ucode and reset/clock init again + 5. zero-out shared mem + 6. download f/w + *******************************************************************/ +static int ipw2100_download_firmware(struct ipw2100_priv *priv) +{ + u32 address; + int err; + +#ifndef CONFIG_PM + /* Fetch the firmware and microcode */ + struct ipw2100_fw ipw2100_firmware; +#endif + + if (priv->fatal_error) { + IPW_DEBUG_ERROR("%s: ipw2100_download_firmware called after " + "fatal error %d. Interface must be brought down.\n", + priv->net_dev->name, priv->fatal_error); + return -EINVAL; + } + +#ifdef CONFIG_PM + if (!ipw2100_firmware.version) { + err = ipw2100_get_firmware(priv, &ipw2100_firmware); + if (err) { + IPW_DEBUG_ERROR("%s: ipw2100_get_firmware failed: %d\n", + priv->net_dev->name, err); + priv->fatal_error = IPW2100_ERR_FW_LOAD; + goto fail; + } + } +#else + err = ipw2100_get_firmware(priv, &ipw2100_firmware); + if (err) { + IPW_DEBUG_ERROR("%s: ipw2100_get_firmware failed: %d\n", + priv->net_dev->name, err); + priv->fatal_error = IPW2100_ERR_FW_LOAD; + goto fail; + } +#endif + priv->firmware_version = ipw2100_firmware.version; + + /* s/w reset and clock stabilization */ + err = sw_reset_and_clock(priv); + if (err) { + IPW_DEBUG_ERROR("%s: sw_reset_and_clock failed: %d\n", + priv->net_dev->name, err); + goto fail; + } + + err = ipw2100_verify(priv); + if (err) { + IPW_DEBUG_ERROR("%s: ipw2100_verify failed: %d\n", + priv->net_dev->name, err); + goto fail; + } + + /* Hold ARC */ + write_nic_dword(priv->net_dev, + IPW_INTERNAL_REGISTER_HALT_AND_RESET, + 0x80000000); + + /* allow ARC to run */ + write_register(priv->net_dev, IPW_REG_RESET_REG, 0); + + /* load microcode */ + err = ipw2100_ucode_download(priv, &ipw2100_firmware); + if (err) { + IPW_DEBUG_ERROR("%s: Error loading microcode: %d\n", + priv->net_dev->name, err); + goto fail; + } + + /* release ARC */ + write_nic_dword(priv->net_dev, + IPW_INTERNAL_REGISTER_HALT_AND_RESET, + 0x00000000); + + /* s/w reset and clock stabilization (again!!!) */ + err = sw_reset_and_clock(priv); + if (err) { + IPW_DEBUG_ERROR("%s: sw_reset_and_clock failed: %d\n", + priv->net_dev->name, err); + goto fail; + } + + /* load f/w */ + err = ipw2100_fw_download(priv, &ipw2100_firmware); + if (err) { + IPW_DEBUG_ERROR("%s: Error loading firmware: %d\n", + priv->net_dev->name, err); + goto fail; + } + +#ifndef CONFIG_PM + /* + * When the .resume method of the driver is called, the other + * part of the system, i.e. the ide driver could still stay in + * the suspend stage. This prevents us from loading the firmware + * from the disk. --YZ + */ + + /* free any storage allocated for firmware image */ + ipw2100_release_firmware(priv, &ipw2100_firmware); +#endif + + /* zero out Domain 1 area indirectly (Si requirement) */ + for (address = IPW_HOST_FW_SHARED_AREA0; + address < IPW_HOST_FW_SHARED_AREA0_END; address += 4) + write_nic_dword(priv->net_dev, address, 0); + for (address = IPW_HOST_FW_SHARED_AREA1; + address < IPW_HOST_FW_SHARED_AREA1_END; address += 4) + write_nic_dword(priv->net_dev, address, 0); + for (address = IPW_HOST_FW_SHARED_AREA2; + address < IPW_HOST_FW_SHARED_AREA2_END; address += 4) + write_nic_dword(priv->net_dev, address, 0); + for (address = IPW_HOST_FW_SHARED_AREA3; + address < IPW_HOST_FW_SHARED_AREA3_END; address += 4) + write_nic_dword(priv->net_dev, address, 0); + for (address = IPW_HOST_FW_INTERRUPT_AREA; + address < IPW_HOST_FW_INTERRUPT_AREA_END; address += 4) + write_nic_dword(priv->net_dev, address, 0); + + return 0; + + fail: + ipw2100_release_firmware(priv, &ipw2100_firmware); + return err; +} + +static inline void ipw2100_enable_interrupts(struct ipw2100_priv *priv) +{ + if (priv->status & STATUS_INT_ENABLED) + return; + priv->status |= STATUS_INT_ENABLED; + write_register(priv->net_dev, IPW_REG_INTA_MASK, IPW_INTERRUPT_MASK); +} + +static inline void ipw2100_disable_interrupts(struct ipw2100_priv *priv) +{ + if (!(priv->status & STATUS_INT_ENABLED)) + return; + priv->status &= ~STATUS_INT_ENABLED; + write_register(priv->net_dev, IPW_REG_INTA_MASK, 0x0); +} + + +static void ipw2100_initialize_ordinals(struct ipw2100_priv *priv) +{ + struct ipw2100_ordinals *ord = &priv->ordinals; + + IPW_DEBUG_INFO("enter\n"); + + read_register(priv->net_dev, IPW_MEM_HOST_SHARED_ORDINALS_TABLE_1, + &ord->table1_addr); + + read_register(priv->net_dev, IPW_MEM_HOST_SHARED_ORDINALS_TABLE_2, + &ord->table2_addr); + + read_nic_dword(priv->net_dev, ord->table1_addr, &ord->table1_size); + read_nic_dword(priv->net_dev, ord->table2_addr, &ord->table2_size); + + ord->table2_size &= 0x0000FFFF; + + IPW_DEBUG_INFO("table 1 size: %d\n", ord->table1_size); + IPW_DEBUG_INFO("table 2 size: %d\n", ord->table2_size); + IPW_DEBUG_INFO("exit\n"); +} + +static inline void ipw2100_hw_set_gpio(struct ipw2100_priv *priv) +{ + u32 reg = 0; + /* + * Set GPIO 3 writable by FW; GPIO 1 writable + * by driver and enable clock + */ + reg = (IPW_BIT_GPIO_GPIO3_MASK | IPW_BIT_GPIO_GPIO1_ENABLE | + IPW_BIT_GPIO_LED_OFF); + write_register(priv->net_dev, IPW_REG_GPIO, reg); +} + +static inline int rf_kill_active(struct ipw2100_priv *priv) +{ +#define MAX_RF_KILL_CHECKS 5 +#define RF_KILL_CHECK_DELAY 40 +#define RF_KILL_CHECK_THRESHOLD 3 + + unsigned short value = 0; + u32 reg = 0; + int i; + + if (!(priv->hw_features & HW_FEATURE_RFKILL)) { + priv->status &= ~STATUS_RF_KILL_HW; + return 0; + } + + for (i = 0; i < MAX_RF_KILL_CHECKS; i++) { + udelay(RF_KILL_CHECK_DELAY); + read_register(priv->net_dev, IPW_REG_GPIO, ®); + value = (value << 1) | ((reg & IPW_BIT_GPIO_RF_KILL) ? 0 : 1); + } + + if (value == 0) + priv->status |= STATUS_RF_KILL_HW; + else + priv->status &= ~STATUS_RF_KILL_HW; + + return (value == 0); +} + +static int ipw2100_get_hw_features(struct ipw2100_priv *priv) +{ + u32 addr, len; + u32 val; + + /* + * EEPROM_SRAM_DB_START_ADDRESS using ordinal in ordinal table 1 + */ + len = sizeof(addr); + if (ipw2100_get_ordinal( + priv, IPW_ORD_EEPROM_SRAM_DB_BLOCK_START_ADDRESS, + &addr, &len)) { + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + return -EIO; + } + + IPW_DEBUG_INFO("EEPROM address: %08X\n", addr); + + /* + * EEPROM version is the byte at offset 0xfd in firmware + * We read 4 bytes, then shift out the byte we actually want */ + read_nic_dword(priv->net_dev, addr + 0xFC, &val); + priv->eeprom_version = (val >> 24) & 0xFF; + IPW_DEBUG_INFO("EEPROM version: %d\n", priv->eeprom_version); + + /* + * HW RF Kill enable is bit 0 in byte at offset 0x21 in firmware + * + * notice that the EEPROM bit is reverse polarity, i.e. + * bit = 0 signifies HW RF kill switch is supported + * bit = 1 signifies HW RF kill switch is NOT supported + */ + read_nic_dword(priv->net_dev, addr + 0x20, &val); + if (!((val >> 24) & 0x01)) + priv->hw_features |= HW_FEATURE_RFKILL; + + IPW_DEBUG_INFO("HW RF Kill: %ssupported.\n", + (priv->hw_features & HW_FEATURE_RFKILL) ? + "" : "not "); + + return 0; +} + +/* + * Start firmware execution after power on and intialization + * The sequence is: + * 1. Release ARC + * 2. Wait for f/w initialization completes; + */ +static int ipw2100_start_adapter(struct ipw2100_priv *priv) +{ +#define IPW_WAIT_FW_INIT_COMPLETE_DELAY (40 * HZ / 1000) + int i; + u32 inta, inta_mask, gpio; + + IPW_DEBUG_INFO("enter\n"); + + if (priv->status & STATUS_RUNNING) + return 0; + + /* + * Initialize the hw - drive adapter to DO state by setting + * init_done bit. Wait for clk_ready bit and Download + * fw & dino ucode + */ + if (ipw2100_download_firmware(priv)) { + IPW_DEBUG_ERROR("%s: Failed to power on the adapter.\n", + priv->net_dev->name); + return -EIO; + } + + /* Clear the Tx, Rx and Msg queues and the r/w indexes + * in the firmware RBD and TBD ring queue */ + ipw2100_queues_initialize(priv); + + ipw2100_hw_set_gpio(priv); + + /* TODO -- Look at disabling interrupts here to make sure none + * get fired during FW initialization */ + + /* Release ARC - clear reset bit */ + write_register(priv->net_dev, IPW_REG_RESET_REG, 0); + + /* wait for f/w intialization complete */ + IPW_DEBUG_FW("Waiting for f/w initialization to complete...\n"); + i = 5000; + do { + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(IPW_WAIT_FW_INIT_COMPLETE_DELAY); + /* Todo... wait for sync command ... */ + + read_register(priv->net_dev, IPW_REG_INTA, &inta); + + /* check "init done" bit */ + if (inta & IPW2100_INTA_FW_INIT_DONE) { + /* reset "init done" bit */ + write_register(priv->net_dev, IPW_REG_INTA, + IPW2100_INTA_FW_INIT_DONE); + break; + } + + /* check error conditions : we check these after the firmware + * check so that if there is an error, the interrupt handler + * will see it and the adapter will be reset */ + if (inta & + (IPW2100_INTA_FATAL_ERROR | IPW2100_INTA_PARITY_ERROR)) { + /* clear error conditions */ + write_register(priv->net_dev, IPW_REG_INTA, + IPW2100_INTA_FATAL_ERROR | + IPW2100_INTA_PARITY_ERROR); + } + } while (i--); + + /* Clear out any pending INTAs since we aren't supposed to have + * interrupts enabled at this point... */ + read_register(priv->net_dev, IPW_REG_INTA, &inta); + read_register(priv->net_dev, IPW_REG_INTA_MASK, &inta_mask); + inta &= IPW_INTERRUPT_MASK; + /* Clear out any pending interrupts */ + if (inta & inta_mask) + write_register(priv->net_dev, IPW_REG_INTA, inta); + + IPW_DEBUG_FW("f/w initialization complete: %s\n", + i ? "SUCCESS" : "FAILED"); + + if (!i) { + IPW_DEBUG_WARNING("%s: Firmware did not initialize.\n", + priv->net_dev->name); + return -EIO; + } + + /* allow firmware to write to GPIO1 & GPIO3 */ + read_register(priv->net_dev, IPW_REG_GPIO, &gpio); + + gpio |= (IPW_BIT_GPIO_GPIO1_MASK | IPW_BIT_GPIO_GPIO3_MASK); + + write_register(priv->net_dev, IPW_REG_GPIO, gpio); + + /* Ready to receive commands */ + priv->status |= STATUS_RUNNING; + + /* The adapter has been reset; we are not associated */ + priv->status &= ~(STATUS_ASSOCIATING | STATUS_ASSOCIATED); + + IPW_DEBUG_INFO("exit\n"); + + return 0; +} + +static inline void ipw2100_reset_fatalerror(struct ipw2100_priv *priv) +{ + if (!priv->fatal_error) + return; + + priv->fatal_errors[priv->fatal_index++] = priv->fatal_error; + priv->fatal_index %= IPW2100_ERROR_QUEUE; + priv->fatal_error = 0; +} + + +/* NOTE: Our interrupt is disabled when this method is called */ +static int ipw2100_power_cycle_adapter(struct ipw2100_priv *priv) +{ + u32 reg; + int i; + + IPW_DEBUG_INFO("Power cycling the hardware.\n"); + + ipw2100_hw_set_gpio(priv); + + /* Step 1. Stop Master Assert */ + write_register(priv->net_dev, IPW_REG_RESET_REG, + IPW_AUX_HOST_RESET_REG_STOP_MASTER); + + /* Step 2. Wait for stop Master Assert + * (not more then 50us, otherwise ret error */ + i = 5; + do { + udelay(IPW_WAIT_RESET_MASTER_ASSERT_COMPLETE_DELAY); + read_register(priv->net_dev, IPW_REG_RESET_REG, ®); + + if (reg & IPW_AUX_HOST_RESET_REG_MASTER_DISABLED) + break; + } while(i--); + + priv->status &= ~STATUS_RESET_PENDING; + + if (!i) { + IPW_DEBUG_INFO("exit - waited too long for master assert stop\n"); + return -EIO; + } + + write_register(priv->net_dev, IPW_REG_RESET_REG, + IPW_AUX_HOST_RESET_REG_SW_RESET); + + + /* Reset any fatal_error conditions */ + ipw2100_reset_fatalerror(priv); + + /* At this point, the adapter is now stopped and disabled */ + priv->status &= ~(STATUS_RUNNING | STATUS_ASSOCIATING | + STATUS_ASSOCIATED | STATUS_ENABLED); + + return 0; +} + +/* + * Send the CARD_DISABLE_PHY_OFF comamnd to the card to disable it + * + * After disabling, if the card was associated, a STATUS_ASSN_LOST will be sent. + * + * STATUS_CARD_DISABLE_NOTIFICATION will be sent regardless of + * if STATUS_ASSN_LOST is sent. + */ +static int ipw2100_hw_phy_off(struct ipw2100_priv *priv) +{ + +#define HW_PHY_OFF_LOOP_DELAY (HZ / 5000) + + struct host_command cmd = { + .host_command = CARD_DISABLE_PHY_OFF, + .host_command_sequence = 0, + .host_command_length = 0, + }; + int err, i; + u32 val1, val2; + + IPW_DEBUG_HC("CARD_DISABLE_PHY_OFF\n"); + + /* Turn off the radio */ + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + + for (i = 0; i < 2500; i++) { + read_nic_dword(priv->net_dev, IPW2100_CONTROL_REG, &val1); + read_nic_dword(priv->net_dev, IPW2100_COMMAND, &val2); + + if ((val1 & IPW2100_CONTROL_PHY_OFF) && + (val2 & IPW2100_COMMAND_PHY_OFF)) + return 0; + + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(HW_PHY_OFF_LOOP_DELAY); + } + + return -EIO; +} + + +static int ipw2100_enable_adapter(struct ipw2100_priv *priv) +{ + struct host_command cmd = { + .host_command = HOST_COMPLETE, + .host_command_sequence = 0, + .host_command_length = 0 + }; + int err = 0; + + IPW_DEBUG_HC("HOST_COMPLETE\n"); + + if (priv->status & STATUS_ENABLED) + return 0; + + down(&priv->adapter_sem); + + if (rf_kill_active(priv)) { + IPW_DEBUG_HC("Command aborted due to RF kill active.\n"); + goto fail_up; + } + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) { + IPW_DEBUG_INFO("Failed to send HOST_COMPLETE command\n"); + goto fail_up; + } + + err = ipw2100_wait_for_card_state(priv, IPW_HW_STATE_ENABLED); + if (err) { + IPW_DEBUG_INFO( + "%s: card not responding to init command.\n", + priv->net_dev->name); + goto fail_up; + } + + if (priv->stop_hang_check) { + priv->stop_hang_check = 0; + queue_delayed_work(priv->workqueue, &priv->hang_check, HZ / 2); + } + +fail_up: + up(&priv->adapter_sem); + return err; +} + +static int ipw2100_hw_stop_adapter(struct ipw2100_priv *priv) +{ +#define HW_POWER_DOWN_DELAY (HZ / 10) + + struct host_command cmd = { + .host_command = HOST_PRE_POWER_DOWN, + .host_command_sequence = 0, + .host_command_length = 0, + }; + int err, i; + u32 reg; + + if (!(priv->status & STATUS_RUNNING)) + return 0; + + priv->status |= STATUS_STOPPING; + + /* We can only shut down the card if the firmware is operational. So, + * if we haven't reset since a fatal_error, then we can not send the + * shutdown commands. */ + if (!priv->fatal_error) { + /* First, make sure the adapter is enabled so that the PHY_OFF + * command can shut it down */ + ipw2100_enable_adapter(priv); + + err = ipw2100_hw_phy_off(priv); + if (err) + IPW_DEBUG_WARNING("Error disabling radio %d\n", err); + + /* + * If in D0-standby mode going directly to D3 may cause a + * PCI bus violation. Therefore we must change out of the D0 + * state. + * + * Sending the PREPARE_FOR_POWER_DOWN will restrict the + * hardware from going into standby mode and will transition + * out of D0-standy if it is already in that state. + * + * STATUS_PREPARE_POWER_DOWN_COMPLETE will be sent by the + * driver upon completion. Once received, the driver can + * proceed to the D3 state. + * + * Prepare for power down command to fw. This command would + * take HW out of D0-standby and prepare it for D3 state. + * + * Currently FW does not support event notification for this + * event. Therefore, skip waiting for it. Just wait a fixed + * 100ms + */ + IPW_DEBUG_HC("HOST_PRE_POWER_DOWN\n"); + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + IPW_DEBUG_WARNING( + "%s: Power down command failed: Error %d\n", + priv->net_dev->name, err); + else { + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(HW_POWER_DOWN_DELAY); + } + } + + priv->status &= ~STATUS_ENABLED; + + /* + * Set GPIO 3 writable by FW; GPIO 1 writable + * by driver and enable clock + */ + ipw2100_hw_set_gpio(priv); + + /* + * Power down adapter. Sequence: + * 1. Stop master assert (RESET_REG[9]=1) + * 2. Wait for stop master (RESET_REG[8]==1) + * 3. S/w reset assert (RESET_REG[7] = 1) + */ + + /* Stop master assert */ + write_register(priv->net_dev, IPW_REG_RESET_REG, + IPW_AUX_HOST_RESET_REG_STOP_MASTER); + + /* wait stop master not more than 50 usec. + * Otherwise return error. */ + for (i = 5; i > 0; i--) { + udelay(10); + + /* Check master stop bit */ + read_register(priv->net_dev, IPW_REG_RESET_REG, ®); + + if (reg & IPW_AUX_HOST_RESET_REG_MASTER_DISABLED) + break; + } + + if (i == 0) + IPW_DEBUG_WARNING(DRV_NAME + ": %s: Could now power down adapter.\n", + priv->net_dev->name); + + /* assert s/w reset */ + write_register(priv->net_dev, IPW_REG_RESET_REG, + IPW_AUX_HOST_RESET_REG_SW_RESET); + + priv->status &= ~(STATUS_RUNNING | STATUS_STOPPING); + + return 0; +} + + +static int ipw2100_disable_adapter(struct ipw2100_priv *priv) +{ + struct host_command cmd = { + .host_command = CARD_DISABLE, + .host_command_sequence = 0, + .host_command_length = 0 + }; + int err = 0; + + IPW_DEBUG_HC("CARD_DISABLE\n"); + + if (!(priv->status & STATUS_ENABLED)) + return 0; + + /* Make sure we clear the associated state */ + priv->status &= ~(STATUS_ASSOCIATED | STATUS_ASSOCIATING); + + if (!priv->stop_hang_check) { + priv->stop_hang_check = 1; + cancel_delayed_work(&priv->hang_check); + } + + down(&priv->adapter_sem); + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) { + IPW_DEBUG_WARNING("exit - failed to send CARD_DISABLE command\n"); + goto fail_up; + } + + err = ipw2100_wait_for_card_state(priv, IPW_HW_STATE_DISABLED); + if (err) { + IPW_DEBUG_WARNING("exit - card failed to change to DISABLED\n"); + goto fail_up; + } + + IPW_DEBUG_INFO("TODO: implement scan state machine\n"); + +fail_up: + up(&priv->adapter_sem); + return err; +} + +int ipw2100_set_scan_options(struct ipw2100_priv *priv) +{ + struct host_command cmd = { + .host_command = SET_SCAN_OPTIONS, + .host_command_sequence = 0, + .host_command_length = 8 + }; + int err; + + IPW_DEBUG_INFO("enter\n"); + + IPW_DEBUG_SCAN("setting scan options\n"); + + cmd.host_command_parameters[0] = 0; + + if (!(priv->config & CFG_ASSOCIATE)) + cmd.host_command_parameters[0] |= IPW_SCAN_NOASSOCIATE; + if ((priv->sec.flags & SEC_ENABLED) && priv->sec.enabled) + cmd.host_command_parameters[0] |= IPW_SCAN_MIXED_CELL; + if (priv->config & CFG_PASSIVE_SCAN) + cmd.host_command_parameters[0] |= IPW_SCAN_PASSIVE; + + cmd.host_command_parameters[1] = priv->channel_mask; + + err = ipw2100_hw_send_command(priv, &cmd); + + IPW_DEBUG_HC("SET_SCAN_OPTIONS 0x%04X\n", + cmd.host_command_parameters[0]); + + return err; +} + +int ipw2100_start_scan(struct ipw2100_priv *priv) +{ + struct host_command cmd = { + .host_command = BROADCAST_SCAN, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + IPW_DEBUG_HC("START_SCAN\n"); + + cmd.host_command_parameters[0] = 0; + + /* No scanning if in monitor mode */ + if (priv->ieee->iw_mode == IW_MODE_MONITOR) + return 1; + + if (priv->status & STATUS_SCANNING) { + IPW_DEBUG_SCAN("Scan requested while already in scan...\n"); + return 0; + } + + IPW_DEBUG_INFO("enter\n"); + + /* Not clearing here; doing so makes iwlist always return nothing... + * + * We should modify the table logic to use aging tables vs. clearing + * the table on each scan start. + */ + IPW_DEBUG_SCAN("starting scan\n"); + + priv->status |= STATUS_SCANNING; + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + priv->status &= ~STATUS_SCANNING; + + IPW_DEBUG_INFO("exit\n"); + + return err; +} + +static int ipw2100_up(struct ipw2100_priv *priv, int deferred) +{ + unsigned long flags; + int rc = 0; + u32 lock; + u32 ord_len = sizeof(lock); + + /* Quite if manually disabled. */ + if (priv->status & STATUS_RF_KILL_SW) { + IPW_DEBUG_INFO("%s: Radio is disabled by Manual Disable " + "switch\n", priv->net_dev->name); + return 0; + } + + /* If the interrupt is enabled, turn it off... */ + spin_lock_irqsave(&priv->low_lock, flags); + ipw2100_disable_interrupts(priv); + + /* Reset any fatal_error conditions */ + ipw2100_reset_fatalerror(priv); + spin_unlock_irqrestore(&priv->low_lock, flags); + + if (priv->status & STATUS_POWERED || + (priv->status & STATUS_RESET_PENDING)) { + /* Power cycle the card ... */ + if (ipw2100_power_cycle_adapter(priv)) { + IPW_DEBUG_WARNING("%s: Could not cycle adapter.\n", + priv->net_dev->name); + rc = 1; + goto exit; + } + } else + priv->status |= STATUS_POWERED; + + /* Load the firmeware, start the clocks, etc. */ + if (ipw2100_start_adapter(priv)) { + IPW_DEBUG_ERROR("%s: Failed to start the firmware.\n", + priv->net_dev->name); + rc = 1; + goto exit; + } + + ipw2100_initialize_ordinals(priv); + + /* Determine capabilities of this particular HW configuration */ + if (ipw2100_get_hw_features(priv)) { + IPW_DEBUG_ERROR("%s: Failed to determine HW features.\n", + priv->net_dev->name); + rc = 1; + goto exit; + } + + lock = LOCK_NONE; + if (ipw2100_set_ordinal(priv, IPW_ORD_PERS_DB_LOCK, &lock, &ord_len)) { + IPW_DEBUG_ERROR("%s: Failed to clear ordinal lock.\n", + priv->net_dev->name); + rc = 1; + goto exit; + } + + priv->status &= ~STATUS_SCANNING; + + if (rf_kill_active(priv)) { + printk(KERN_INFO "%s: Radio is disabled by RF switch.\n", + priv->net_dev->name); + + if (priv->stop_rf_kill) { + priv->stop_rf_kill = 0; + queue_delayed_work(priv->workqueue, &priv->rf_kill, HZ); + } + + deferred = 1; + } + + /* Turn on the interrupt so that commands can be processed */ + ipw2100_enable_interrupts(priv); + + /* Send all of the commands that must be sent prior to + * HOST_COMPLETE */ + if (ipw2100_adapter_setup(priv)) { + IPW_DEBUG_ERROR("%s: Failed to start the card.\n", + priv->net_dev->name); + rc = 1; + goto exit; + } + + if (!deferred) { + /* Enable the adapter - sends HOST_COMPLETE */ + if (ipw2100_enable_adapter(priv)) { + IPW_DEBUG_ERROR( + "%s: failed in call to enable adapter.\n", + priv->net_dev->name); + ipw2100_hw_stop_adapter(priv); + rc = 1; + goto exit; + } + + + /* Start a scan . . . */ + ipw2100_set_scan_options(priv); + ipw2100_start_scan(priv); + } + + exit: + return rc; +} + +/* Called by register_netdev() */ +static int ipw2100_net_init(struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + return ipw2100_up(priv, 1); +} + +static void ipw2100_down(struct ipw2100_priv *priv) +{ + unsigned long flags; + union iwreq_data wrqu = { + .ap_addr = { + .sa_family = ARPHRD_ETHER + } + }; + int associated = priv->status & STATUS_ASSOCIATED; + + /* Kill the RF switch timer */ + if (!priv->stop_rf_kill) { + priv->stop_rf_kill = 1; + cancel_delayed_work(&priv->rf_kill); + } + + /* Kill the firmare hang check timer */ + if (!priv->stop_hang_check) { + priv->stop_hang_check = 1; + cancel_delayed_work(&priv->hang_check); + } + + /* Kill any pending resets */ + if (priv->status & STATUS_RESET_PENDING) + cancel_delayed_work(&priv->reset_work); + + /* Make sure the interrupt is on so that FW commands will be + * processed correctly */ + spin_lock_irqsave(&priv->low_lock, flags); + ipw2100_enable_interrupts(priv); + spin_unlock_irqrestore(&priv->low_lock, flags); + + if (ipw2100_hw_stop_adapter(priv)) + IPW_DEBUG_ERROR("%s: Error stopping adapter.\n", + priv->net_dev->name); + + /* Do not disable the interrupt until _after_ we disable + * the adaptor. Otherwise the CARD_DISABLE command will never + * be ack'd by the firmware */ + spin_lock_irqsave(&priv->low_lock, flags); + ipw2100_disable_interrupts(priv); + spin_unlock_irqrestore(&priv->low_lock, flags); + +#ifdef ACPI_CSTATE_LIMIT_DEFINED + if (priv->config & CFG_C3_DISABLED) { + IPW_DEBUG_INFO(DRV_NAME ": Resetting C3 transitions.\n"); + acpi_set_cstate_limit(priv->cstate_limit); + priv->config &= ~CFG_C3_DISABLED; + } +#endif + + /* We have to signal any supplicant if we are disassociating */ + if (associated) + wireless_send_event(priv->net_dev, SIOCGIWAP, &wrqu, NULL); + + priv->status &= ~(STATUS_ASSOCIATED | STATUS_ASSOCIATING); + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); +} + +void ipw2100_reset_adapter(struct ipw2100_priv *priv) +{ + unsigned long flags; + union iwreq_data wrqu = { + .ap_addr = { + .sa_family = ARPHRD_ETHER + } + }; + int associated = priv->status & STATUS_ASSOCIATED; + + spin_lock_irqsave(&priv->low_lock, flags); + IPW_DEBUG_INFO(DRV_NAME ": %s: Restarting adapter.\n", + priv->net_dev->name); + priv->resets++; + priv->status &= ~(STATUS_ASSOCIATED | STATUS_ASSOCIATING); + priv->status |= STATUS_SECURITY_UPDATED; + + /* Force a power cycle even if interface hasn't been opened + * yet */ + cancel_delayed_work(&priv->reset_work); + priv->status |= STATUS_RESET_PENDING; + spin_unlock_irqrestore(&priv->low_lock, flags); + + down(&priv->action_sem); + /* stop timed checks so that they don't interfere with reset */ + priv->stop_hang_check = 1; + cancel_delayed_work(&priv->hang_check); + + /* We have to signal any supplicant if we are disassociating */ + if (associated) + wireless_send_event(priv->net_dev, SIOCGIWAP, &wrqu, NULL); + + ipw2100_up(priv, 0); + up(&priv->action_sem); + +} + + +static void isr_indicate_associated(struct ipw2100_priv *priv, u32 status) +{ + +#define MAC_ASSOCIATION_READ_DELAY (HZ) + int ret, len, essid_len; + char essid[IW_ESSID_MAX_SIZE]; + u32 txrate; + u32 chan; + char *txratename; + u8 bssid[ETH_ALEN]; + + /* + * TBD: BSSID is usually 00:00:00:00:00:00 here and not + * an actual MAC of the AP. Seems like FW sets this + * address too late. Read it later and expose through + * /proc or schedule a later task to query and update + */ + + essid_len = IW_ESSID_MAX_SIZE; + ret = ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_SSID, + essid, &essid_len); + if (ret) { + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + return; + } + + len = sizeof(u32); + ret = ipw2100_get_ordinal(priv, IPW_ORD_CURRENT_TX_RATE, + &txrate, &len); + if (ret) { + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + return; + } + + len = sizeof(u32); + ret = ipw2100_get_ordinal(priv, IPW_ORD_OUR_FREQ, &chan, &len); + if (ret) { + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + return; + } + len = ETH_ALEN; + ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_AP_BSSID, &bssid, &len); + if (ret) { + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + return; + } + memcpy(priv->ieee->bssid, bssid, ETH_ALEN); + + + switch (txrate) { + case TX_RATE_1_MBIT: + txratename = "1Mbps"; + break; + case TX_RATE_2_MBIT: + txratename = "2Mbsp"; + break; + case TX_RATE_5_5_MBIT: + txratename = "5.5Mbps"; + break; + case TX_RATE_11_MBIT: + txratename = "11Mbps"; + break; + default: + IPW_DEBUG_INFO("Unknown rate: %d\n", txrate); + txratename = "unknown rate"; + break; + } + + IPW_DEBUG_INFO("%s: Associated with '%s' at %s, channel %d (BSSID=" + MAC_FMT ")\n", + priv->net_dev->name, escape_essid(essid, essid_len), + txratename, chan, MAC_ARG(bssid)); + + /* now we copy read ssid into dev */ + if (!(priv->config & CFG_STATIC_ESSID)) { + priv->essid_len = min((u8)essid_len, (u8)IW_ESSID_MAX_SIZE); + memcpy(priv->essid, essid, priv->essid_len); + } + priv->channel = chan; + memcpy(priv->bssid, bssid, ETH_ALEN); + + priv->status |= STATUS_ASSOCIATING; + priv->connect_start = get_seconds(); + + queue_delayed_work(priv->workqueue, &priv->wx_event_work, HZ / 10); +} + + +int ipw2100_set_essid(struct ipw2100_priv *priv, char *essid, + int length, int batch_mode) +{ + int ssid_len = min(length, IW_ESSID_MAX_SIZE); + struct host_command cmd = { + .host_command = SSID, + .host_command_sequence = 0, + .host_command_length = ssid_len + }; + int err; + + IPW_DEBUG_HC("SSID: '%s'\n", escape_essid(essid, ssid_len)); + + if (ssid_len) + memcpy((char*)cmd.host_command_parameters, + essid, ssid_len); + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + /* Bug in FW currently doesn't honor bit 0 in SET_SCAN_OPTIONS to + * disable auto association -- so we cheat by setting a bogus SSID */ + if (!ssid_len && !(priv->config & CFG_ASSOCIATE)) { + int i; + u8 *bogus = (u8*)cmd.host_command_parameters; + for (i = 0; i < IW_ESSID_MAX_SIZE; i++) + bogus[i] = 0x18 + i; + cmd.host_command_length = IW_ESSID_MAX_SIZE; + } + + /* NOTE: We always send the SSID command even if the provided ESSID is + * the same as what we currently think is set. */ + + err = ipw2100_hw_send_command(priv, &cmd); + if (!err) { + memset(priv->essid + ssid_len, 0, + IW_ESSID_MAX_SIZE - ssid_len); + memcpy(priv->essid, essid, ssid_len); + priv->essid_len = ssid_len; + } + + if (!batch_mode) { + if (ipw2100_enable_adapter(priv)) + err = -EIO; + } + + return err; +} + +static void isr_indicate_association_lost(struct ipw2100_priv *priv, u32 status) +{ + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "disassociated: '%s' " MAC_FMT " \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + + priv->status &= ~(STATUS_ASSOCIATED | STATUS_ASSOCIATING); + + if (priv->status & STATUS_STOPPING) { + IPW_DEBUG_INFO("Card is stopping itself, discard ASSN_LOST.\n"); + return; + } + + memset(priv->bssid, 0, ETH_ALEN); + memset(priv->ieee->bssid, 0, ETH_ALEN); + + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); + + if (!(priv->status & STATUS_RUNNING)) + return; + + if (priv->status & STATUS_SECURITY_UPDATED) + queue_work(priv->workqueue, &priv->security_work); + + queue_work(priv->workqueue, &priv->wx_event_work); +} + +static void isr_indicate_rf_kill(struct ipw2100_priv *priv, u32 status) +{ + IPW_DEBUG_INFO("%s: RF Kill state changed to radio OFF.\n", + priv->net_dev->name); + + /* RF_KILL is now enabled (else we wouldn't be here) */ + priv->status |= STATUS_RF_KILL_HW; + +#ifdef ACPI_CSTATE_LIMIT_DEFINED + if (priv->config & CFG_C3_DISABLED) { + IPW_DEBUG_INFO(DRV_NAME ": Resetting C3 transitions.\n"); + acpi_set_cstate_limit(priv->cstate_limit); + priv->config &= ~CFG_C3_DISABLED; + } +#endif + + /* Make sure the RF Kill check timer is running */ + priv->stop_rf_kill = 0; + cancel_delayed_work(&priv->rf_kill); + queue_delayed_work(priv->workqueue, &priv->rf_kill, HZ); +} + +static void isr_scan_complete(struct ipw2100_priv *priv, u32 status) +{ + IPW_DEBUG_SCAN("scan complete\n"); + /* Age the scan results... */ + priv->ieee->scans++; + priv->status &= ~STATUS_SCANNING; +} + +#ifdef CONFIG_IPW_DEBUG +#define IPW2100_HANDLER(v, f) { v, f, # v } +struct ipw2100_status_indicator { + int status; + void (*cb)(struct ipw2100_priv *priv, u32 status); + char *name; +}; +#else +#define IPW2100_HANDLER(v, f) { v, f } +struct ipw2100_status_indicator { + int status; + void (*cb)(struct ipw2100_priv *priv, u32 status); +}; +#endif /* CONFIG_IPW_DEBUG */ + +static void isr_indicate_scanning(struct ipw2100_priv *priv, u32 status) +{ + IPW_DEBUG_SCAN("Scanning...\n"); + priv->status |= STATUS_SCANNING; +} + +const struct ipw2100_status_indicator status_handlers[] = { + IPW2100_HANDLER(IPW_STATE_INITIALIZED, 0), + IPW2100_HANDLER(IPW_STATE_COUNTRY_FOUND, 0), + IPW2100_HANDLER(IPW_STATE_ASSOCIATED, isr_indicate_associated), + IPW2100_HANDLER(IPW_STATE_ASSN_LOST, isr_indicate_association_lost), + IPW2100_HANDLER(IPW_STATE_ASSN_CHANGED, 0), + IPW2100_HANDLER(IPW_STATE_SCAN_COMPLETE, isr_scan_complete), + IPW2100_HANDLER(IPW_STATE_ENTERED_PSP, 0), + IPW2100_HANDLER(IPW_STATE_LEFT_PSP, 0), + IPW2100_HANDLER(IPW_STATE_RF_KILL, isr_indicate_rf_kill), + IPW2100_HANDLER(IPW_STATE_DISABLED, 0), + IPW2100_HANDLER(IPW_STATE_POWER_DOWN, 0), + IPW2100_HANDLER(IPW_STATE_SCANNING, isr_indicate_scanning), + IPW2100_HANDLER(-1, 0) +}; + + +static void isr_status_change(struct ipw2100_priv *priv, int status) +{ + int i; + + if (status == IPW_STATE_SCANNING && + priv->status & STATUS_ASSOCIATED && + !(priv->status & STATUS_SCANNING)) { + IPW_DEBUG_INFO("Scan detected while associated, with " + "no scan request. Restarting firmware.\n"); + + /* Wake up any sleeping jobs */ + schedule_reset(priv); + } + + for (i = 0; status_handlers[i].status != -1; i++) { + if (status == status_handlers[i].status) { + IPW_DEBUG_NOTIF("Status change: %s\n", + status_handlers[i].name); + if (status_handlers[i].cb) + status_handlers[i].cb(priv, status); + priv->wstats.status = status; + return; + } + } + + IPW_DEBUG_NOTIF("unknown status received: %04x\n", status); +} + +static void isr_rx_complete_command( + struct ipw2100_priv *priv, + struct ipw2100_cmd_header *cmd) +{ +#ifdef CONFIG_IPW_DEBUG + if (cmd->host_command_reg < ARRAY_SIZE(command_types)) { + IPW_DEBUG_HC("Command completed '%s (%d)'\n", + command_types[cmd->host_command_reg], + cmd->host_command_reg); + } +#endif + if (cmd->host_command_reg == HOST_COMPLETE) + priv->status |= STATUS_ENABLED; + + if (cmd->host_command_reg == CARD_DISABLE) + priv->status &= ~STATUS_ENABLED; + + priv->status &= ~STATUS_CMD_ACTIVE; + + wake_up_interruptible(&priv->wait_command_queue); +} + +#ifdef CONFIG_IPW_DEBUG +const char *frame_types[] = { + "COMMAND_STATUS_VAL", + "STATUS_CHANGE_VAL", + "P80211_DATA_VAL", + "P8023_DATA_VAL", + "HOST_NOTIFICATION_VAL" +}; +#endif + + +static inline int ipw2100_alloc_skb( + struct ipw2100_priv *priv, + struct ipw2100_rx_packet *packet) +{ + packet->skb = dev_alloc_skb(sizeof(struct ipw2100_rx)); + if (!packet->skb) + return -ENOMEM; + + packet->rxp = (struct ipw2100_rx *)packet->skb->data; + packet->dma_addr = pci_map_single(priv->pci_dev, packet->skb->data, + sizeof(struct ipw2100_rx), + PCI_DMA_FROMDEVICE); + /* NOTE: pci_map_single does not return an error code, and 0 is a valid + * dma_addr */ + + return 0; +} + + +#define SEARCH_ERROR 0xffffffff +#define SEARCH_FAIL 0xfffffffe +#define SEARCH_SUCCESS 0xfffffff0 +#define SEARCH_DISCARD 0 +#define SEARCH_SNAPSHOT 1 + +#define SNAPSHOT_ADDR(ofs) (priv->snapshot[((ofs) >> 12) & 0xff] + ((ofs) & 0xfff)) +static inline int ipw2100_snapshot_alloc(struct ipw2100_priv *priv) +{ + int i; + if (priv->snapshot[0]) + return 1; + for (i = 0; i < 0x30; i++) { + priv->snapshot[i] = (u8*)kmalloc(0x1000, GFP_ATOMIC); + if (!priv->snapshot[i]) { + IPW_DEBUG_INFO("%s: Error allocating snapshot " + "buffer %d\n", priv->net_dev->name, i); + while (i > 0) + kfree(priv->snapshot[--i]); + priv->snapshot[0] = NULL; + return 0; + } + } + + return 1; +} + +static inline void ipw2100_snapshot_free(struct ipw2100_priv *priv) +{ + int i; + if (!priv->snapshot[0]) + return; + for (i = 0; i < 0x30; i++) + kfree(priv->snapshot[i]); + priv->snapshot[0] = NULL; +} + +static inline u32 ipw2100_match_buf(struct ipw2100_priv *priv, u8 *in_buf, + size_t len, int mode) +{ + u32 i, j; + u32 tmp; + u8 *s, *d; + u32 ret; + + s = in_buf; + if (mode == SEARCH_SNAPSHOT) { + if (!ipw2100_snapshot_alloc(priv)) + mode = SEARCH_DISCARD; + } + + for (ret = SEARCH_FAIL, i = 0; i < 0x30000; i += 4) { + read_nic_dword(priv->net_dev, i, &tmp); + if (mode == SEARCH_SNAPSHOT) + *(u32 *)SNAPSHOT_ADDR(i) = tmp; + if (ret == SEARCH_FAIL) { + d = (u8*)&tmp; + for (j = 0; j < 4; j++) { + if (*s != *d) { + s = in_buf; + continue; + } + + s++; + d++; + + if ((s - in_buf) == len) + ret = (i + j) - len + 1; + } + } else if (mode == SEARCH_DISCARD) + return ret; + } + + return ret; +} + +/* + * + * 0) Disconnect the SKB from the firmware (just unmap) + * 1) Pack the ETH header into the SKB + * 2) Pass the SKB to the network stack + * + * When packet is provided by the firmware, it contains the following: + * + * . ieee80211_hdr + * . ieee80211_snap_hdr + * + * The size of the constructed ethernet + * + */ +#ifdef CONFIG_IPW2100_RX_DEBUG +u8 packet_data[IPW_RX_NIC_BUFFER_LENGTH]; +#endif + +static inline void ipw2100_corruption_detected(struct ipw2100_priv *priv, + int i) +{ +#ifdef CONFIG_IPW_DEBUG_C3 + struct ipw2100_status *status = &priv->status_queue.drv[i]; + u32 match, reg; + int j; +#endif +#ifdef ACPI_CSTATE_LIMIT_DEFINED + int limit; +#endif + + IPW_DEBUG_INFO(DRV_NAME ": PCI latency error detected at " + "0x%04X.\n", i * sizeof(struct ipw2100_status)); + +#ifdef ACPI_CSTATE_LIMIT_DEFINED + IPW_DEBUG_INFO(DRV_NAME ": Disabling C3 transitions.\n"); + limit = acpi_get_cstate_limit(); + if (limit > 2) { + priv->cstate_limit = limit; + acpi_set_cstate_limit(2); + priv->config |= CFG_C3_DISABLED; + } +#endif + +#ifdef CONFIG_IPW_DEBUG_C3 + /* Halt the fimrware so we can get a good image */ + write_register(priv->net_dev, IPW_REG_RESET_REG, + IPW_AUX_HOST_RESET_REG_STOP_MASTER); + j = 5; + do { + udelay(IPW_WAIT_RESET_MASTER_ASSERT_COMPLETE_DELAY); + read_register(priv->net_dev, IPW_REG_RESET_REG, ®); + + if (reg & IPW_AUX_HOST_RESET_REG_MASTER_DISABLED) + break; + } while (j--); + + match = ipw2100_match_buf(priv, (u8*)status, + sizeof(struct ipw2100_status), + SEARCH_SNAPSHOT); + if (match < SEARCH_SUCCESS) + IPW_DEBUG_INFO("%s: DMA status match in Firmware at " + "offset 0x%06X, length %d:\n", + priv->net_dev->name, match, + sizeof(struct ipw2100_status)); + else + IPW_DEBUG_INFO("%s: No DMA status match in " + "Firmware.\n", priv->net_dev->name); + + printk_buf((u8*)priv->status_queue.drv, + sizeof(struct ipw2100_status) * RX_QUEUE_LENGTH); +#endif + + priv->fatal_error = IPW2100_ERR_C3_CORRUPTION; + priv->ieee->stats.rx_errors++; + schedule_reset(priv); +} + +static inline void isr_rx(struct ipw2100_priv *priv, int i, + struct ieee80211_rx_stats *stats) +{ + struct ipw2100_status *status = &priv->status_queue.drv[i]; + struct ipw2100_rx_packet *packet = &priv->rx_buffers[i]; + + IPW_DEBUG_RX("Handler...\n"); + + if (unlikely(status->frame_size > skb_tailroom(packet->skb))) { + IPW_DEBUG_INFO("%s: frame_size (%u) > skb_tailroom (%u)!" + " Dropping.\n", + priv->net_dev->name, + status->frame_size, skb_tailroom(packet->skb)); + priv->ieee->stats.rx_errors++; + return; + } + + if (unlikely(!netif_running(priv->net_dev))) { + priv->ieee->stats.rx_errors++; + priv->wstats.discard.misc++; + IPW_DEBUG_DROP("Dropping packet while interface is not up.\n"); + return; + } + + if (unlikely(priv->ieee->iw_mode == IW_MODE_MONITOR && + status->flags & IPW_STATUS_FLAG_CRC_ERROR)) { + IPW_DEBUG_RX("CRC error in packet. Dropping.\n"); + priv->ieee->stats.rx_errors++; + return; + } + + if (unlikely(priv->ieee->iw_mode != IW_MODE_MONITOR && + !(priv->status & STATUS_ASSOCIATED))) { + IPW_DEBUG_DROP("Dropping packet while not associated.\n"); + priv->wstats.discard.misc++; + return; + } + + + pci_unmap_single(priv->pci_dev, + packet->dma_addr, + sizeof(struct ipw2100_rx), + PCI_DMA_FROMDEVICE); + + skb_put(packet->skb, status->frame_size); + +#ifdef CONFIG_IPW2100_RX_DEBUG + /* Make a copy of the frame so we can dump it to the logs if + * ieee80211_rx fails */ + memcpy(packet_data, packet->skb->data, + min(status->frame_size, IPW_RX_NIC_BUFFER_LENGTH)); +#endif + + if (!ieee80211_rx(priv->ieee, packet->skb, stats)) { +#ifdef CONFIG_IPW2100_RX_DEBUG + IPW_DEBUG_DROP("%s: Non consumed packet:\n", + priv->net_dev->name); + printk_buf(IPW_DL_DROP, packet_data, status->frame_size); +#endif + priv->ieee->stats.rx_errors++; + + /* ieee80211_rx failed, so it didn't free the SKB */ + dev_kfree_skb_any(packet->skb); + packet->skb = NULL; + } + + /* We need to allocate a new SKB and attach it to the RDB. */ + if (unlikely(ipw2100_alloc_skb(priv, packet))) { + IPW_DEBUG_WARNING( + "%s: Unable to allocate SKB onto RBD ring - disabling " + "adapter.\n", priv->net_dev->name); + /* TODO: schedule adapter shutdown */ + IPW_DEBUG_INFO("TODO: Shutdown adapter...\n"); + } + + /* Update the RDB entry */ + priv->rx_queue.drv[i].host_addr = packet->dma_addr; +} + +static inline int ipw2100_corruption_check(struct ipw2100_priv *priv, int i) +{ + struct ipw2100_status *status = &priv->status_queue.drv[i]; + struct ipw2100_rx *u = priv->rx_buffers[i].rxp; + u16 frame_type = status->status_fields & STATUS_TYPE_MASK; + + switch (frame_type) { + case COMMAND_STATUS_VAL: + return (status->frame_size != sizeof(u->rx_data.command)); + case STATUS_CHANGE_VAL: + return (status->frame_size != sizeof(u->rx_data.status)); + case HOST_NOTIFICATION_VAL: + return (status->frame_size < sizeof(u->rx_data.notification)); + case P80211_DATA_VAL: + case P8023_DATA_VAL: +#ifdef CONFIG_IPW2100_MONITOR + return 0; +#else + switch (WLAN_FC_GET_TYPE(u->rx_data.header.frame_ctl)) { + case IEEE80211_FTYPE_MGMT: + case IEEE80211_FTYPE_CTL: + return 0; + case IEEE80211_FTYPE_DATA: + return (status->frame_size > + IPW_MAX_802_11_PAYLOAD_LENGTH); + } +#endif + } + + return 1; +} + +/* + * ipw2100 interrupts are disabled at this point, and the ISR + * is the only code that calls this method. So, we do not need + * to play with any locks. + * + * RX Queue works as follows: + * + * Read index - firmware places packet in entry identified by the + * Read index and advances Read index. In this manner, + * Read index will always point to the next packet to + * be filled--but not yet valid. + * + * Write index - driver fills this entry with an unused RBD entry. + * This entry has not filled by the firmware yet. + * + * In between the W and R indexes are the RBDs that have been received + * but not yet processed. + * + * The process of handling packets will start at WRITE + 1 and advance + * until it reaches the READ index. + * + * The WRITE index is cached in the variable 'priv->rx_queue.next'. + * + */ +static inline void __ipw2100_rx_process(struct ipw2100_priv *priv) +{ + struct ipw2100_bd_queue *rxq = &priv->rx_queue; + struct ipw2100_status_queue *sq = &priv->status_queue; + struct ipw2100_rx_packet *packet; + u16 frame_type; + u32 r, w, i, s; + struct ipw2100_rx *u; + struct ieee80211_rx_stats stats = { + .mac_time = jiffies, + }; + + read_register(priv->net_dev, IPW_MEM_HOST_SHARED_RX_READ_INDEX, &r); + read_register(priv->net_dev, IPW_MEM_HOST_SHARED_RX_WRITE_INDEX, &w); + + if (r >= rxq->entries) { + IPW_DEBUG_RX("exit - bad read index\n"); + return; + } + + i = (rxq->next + 1) % rxq->entries; + s = i; + while (i != r) { + /* IPW_DEBUG_RX("r = %d : w = %d : processing = %d\n", + r, rxq->next, i); */ + + packet = &priv->rx_buffers[i]; + + /* Sync the DMA for the STATUS buffer so CPU is sure to get + * the correct values */ + pci_dma_sync_single_for_cpu( + priv->pci_dev, + sq->nic + sizeof(struct ipw2100_status) * i, + sizeof(struct ipw2100_status), + PCI_DMA_FROMDEVICE); + + /* Sync the DMA for the RX buffer so CPU is sure to get + * the correct values */ + pci_dma_sync_single_for_cpu(priv->pci_dev, packet->dma_addr, + sizeof(struct ipw2100_rx), + PCI_DMA_FROMDEVICE); + + if (unlikely(ipw2100_corruption_check(priv, i))) { + ipw2100_corruption_detected(priv, i); + goto increment; + } + + u = packet->rxp; + frame_type = sq->drv[i].status_fields & + STATUS_TYPE_MASK; + stats.rssi = sq->drv[i].rssi + IPW2100_RSSI_TO_DBM; + stats.len = sq->drv[i].frame_size; + + stats.mask = 0; + if (stats.rssi != 0) + stats.mask |= IEEE80211_STATMASK_RSSI; + stats.freq = IEEE80211_24GHZ_BAND; + + IPW_DEBUG_RX( + "%s: '%s' frame type received (%d).\n", + priv->net_dev->name, frame_types[frame_type], + stats.len); + + switch (frame_type) { + case COMMAND_STATUS_VAL: + /* Reset Rx watchdog */ + isr_rx_complete_command( + priv, &u->rx_data.command); + break; + + case STATUS_CHANGE_VAL: + isr_status_change(priv, u->rx_data.status); + break; + + case P80211_DATA_VAL: + case P8023_DATA_VAL: +#ifdef CONFIG_IPW2100_MONITOR + if (priv->ieee->iw_mode == IW_MODE_MONITOR) { + isr_rx(priv, i, &stats); + break; + } +#endif + if (stats.len < sizeof(u->rx_data.header)) + break; + switch (WLAN_FC_GET_TYPE(u->rx_data.header. + frame_ctl)) { + case IEEE80211_FTYPE_MGMT: + ieee80211_rx_mgt(priv->ieee, + &u->rx_data.header, + &stats); + break; + + case IEEE80211_FTYPE_CTL: + break; + + case IEEE80211_FTYPE_DATA: + isr_rx(priv, i, &stats); + break; + + } + break; + } + + increment: + /* clear status field associated with this RBD */ + rxq->drv[i].status.info.field = 0; + + i = (i + 1) % rxq->entries; + } + + if (i != s) { + /* backtrack one entry, wrapping to end if at 0 */ + rxq->next = (i ? i : rxq->entries) - 1; + + write_register(priv->net_dev, + IPW_MEM_HOST_SHARED_RX_WRITE_INDEX, + rxq->next); + } +} + + +/* + * __ipw2100_tx_process + * + * This routine will determine whether the next packet on + * the fw_pend_list has been processed by the firmware yet. + * + * If not, then it does nothing and returns. + * + * If so, then it removes the item from the fw_pend_list, frees + * any associated storage, and places the item back on the + * free list of its source (either msg_free_list or tx_free_list) + * + * TX Queue works as follows: + * + * Read index - points to the next TBD that the firmware will + * process. The firmware will read the data, and once + * done processing, it will advance the Read index. + * + * Write index - driver fills this entry with an constructed TBD + * entry. The Write index is not advanced until the + * packet has been configured. + * + * In between the W and R indexes are the TBDs that have NOT been + * processed. Lagging behind the R index are packets that have + * been processed but have not been freed by the driver. + * + * In order to free old storage, an internal index will be maintained + * that points to the next packet to be freed. When all used + * packets have been freed, the oldest index will be the same as the + * firmware's read index. + * + * The OLDEST index is cached in the variable 'priv->tx_queue.oldest' + * + * Because the TBD structure can not contain arbitrary data, the + * driver must keep an internal queue of cached allocations such that + * it can put that data back into the tx_free_list and msg_free_list + * for use by future command and data packets. + * + */ +static inline int __ipw2100_tx_process(struct ipw2100_priv *priv) +{ + struct ipw2100_bd_queue *txq = &priv->tx_queue; + struct ipw2100_bd *tbd; + struct list_head *element; + struct ipw2100_tx_packet *packet; + int descriptors_used; + int e, i; + u32 r, w, frag_num = 0; + + if (list_empty(&priv->fw_pend_list)) + return 0; + + element = priv->fw_pend_list.next; + + packet = list_entry(element, struct ipw2100_tx_packet, list); + tbd = &txq->drv[packet->index]; + + /* Determine how many TBD entries must be finished... */ + switch (packet->type) { + case COMMAND: + /* COMMAND uses only one slot; don't advance */ + descriptors_used = 1; + e = txq->oldest; + break; + + case DATA: + /* DATA uses two slots; advance and loop position. */ + descriptors_used = tbd->num_fragments; + frag_num = tbd->num_fragments - 1; + e = txq->oldest + frag_num; + e %= txq->entries; + break; + + default: + IPW_DEBUG_WARNING("%s: Bad fw_pend_list entry!\n", + priv->net_dev->name); + return 0; + } + + /* if the last TBD is not done by NIC yet, then packet is + * not ready to be released. + * + */ + read_register(priv->net_dev, IPW_MEM_HOST_SHARED_TX_QUEUE_READ_INDEX, + &r); + read_register(priv->net_dev, IPW_MEM_HOST_SHARED_TX_QUEUE_WRITE_INDEX, + &w); + if (w != txq->next) + IPW_DEBUG_WARNING("%s: write index mismatch\n", + priv->net_dev->name); + + /* + * txq->next is the index of the last packet written txq->oldest is + * the index of the r is the index of the next packet to be read by + * firmware + */ + + + /* + * Quick graphic to help you visualize the following + * if / else statement + * + * ===>| s---->|=============== + * e>| + * | a | b | c | d | e | f | g | h | i | j | k | l + * r---->| + * w + * + * w - updated by driver + * r - updated by firmware + * s - start of oldest BD entry (txq->oldest) + * e - end of oldest BD entry + * + */ + if (!((r <= w && (e < r || e >= w)) || (e < r && e >= w))) { + IPW_DEBUG_TX("exit - no processed packets ready to release.\n"); + return 0; + } + + list_del(element); + DEC_STAT(&priv->fw_pend_stat); + +#ifdef CONFIG_IPW_DEBUG + { + int i = txq->oldest; + IPW_DEBUG_TX( + "TX%d V=%p P=%p T=%p L=%d\n", i, + &txq->drv[i], + (void*)txq->nic + i * sizeof(struct ipw2100_bd), + (void*)txq->drv[i].host_addr, + txq->drv[i].buf_length); + + if (packet->type == DATA) { + i = (i + 1) % txq->entries; + + IPW_DEBUG_TX( + "TX%d V=%p P=%p T=%p L=%d\n", i, + &txq->drv[i], + (void*)txq->nic + i * + sizeof(struct ipw2100_bd), + (void*)txq->drv[i].host_addr, + txq->drv[i].buf_length); + } + } +#endif + + switch (packet->type) { + case DATA: + if (txq->drv[txq->oldest].status.info.fields.txType != 0) + IPW_DEBUG_WARNING("%s: Queue mismatch. " + "Expecting DATA TBD but pulled " + "something else: ids %d=%d.\n", + priv->net_dev->name, txq->oldest, packet->index); + + /* DATA packet; we have to unmap and free the SKB */ + priv->ieee->stats.tx_packets++; + for (i = 0; i < frag_num; i++) { + tbd = &txq->drv[(packet->index + 1 + i) % + txq->entries]; + + IPW_DEBUG_TX( + "TX%d P=%08x L=%d\n", + (packet->index + 1 + i) % txq->entries, + tbd->host_addr, tbd->buf_length); + + pci_unmap_single(priv->pci_dev, + tbd->host_addr, + tbd->buf_length, + PCI_DMA_TODEVICE); + } + + priv->ieee->stats.tx_bytes += packet->info.d_struct.txb->payload_size; + ieee80211_txb_free(packet->info.d_struct.txb); + packet->info.d_struct.txb = NULL; + + list_add_tail(element, &priv->tx_free_list); + INC_STAT(&priv->tx_free_stat); + + /* We have a free slot in the Tx queue, so wake up the + * transmit layer if it is stopped. */ + if (priv->status & STATUS_ASSOCIATED && + netif_queue_stopped(priv->net_dev)) { + IPW_DEBUG_INFO(KERN_INFO + "%s: Waking net queue.\n", + priv->net_dev->name); + netif_wake_queue(priv->net_dev); + } + + /* A packet was processed by the hardware, so update the + * watchdog */ + priv->net_dev->trans_start = jiffies; + + break; + + case COMMAND: + if (txq->drv[txq->oldest].status.info.fields.txType != 1) + IPW_DEBUG_WARNING("%s: Queue mismatch. " + "Expecting COMMAND TBD but pulled " + "something else: ids %d=%d.\n", + priv->net_dev->name, txq->oldest, packet->index); + +#ifdef CONFIG_IPW_DEBUG + if (packet->info.c_struct.cmd->host_command_reg < + sizeof(command_types) / sizeof(*command_types)) + IPW_DEBUG_TX( + "Command '%s (%d)' processed: %d.\n", + command_types[packet->info.c_struct.cmd->host_command_reg], + packet->info.c_struct.cmd->host_command_reg, + packet->info.c_struct.cmd->cmd_status_reg); +#endif + + list_add_tail(element, &priv->msg_free_list); + INC_STAT(&priv->msg_free_stat); + break; + } + + /* advance oldest used TBD pointer to start of next entry */ + txq->oldest = (e + 1) % txq->entries; + /* increase available TBDs number */ + txq->available += descriptors_used; + SET_STAT(&priv->txq_stat, txq->available); + + IPW_DEBUG_TX("packet latency (send to process) %ld jiffies\n", + jiffies - packet->jiffy_start); + + return (!list_empty(&priv->fw_pend_list)); +} + + +static inline void __ipw2100_tx_complete(struct ipw2100_priv *priv) +{ + int i = 0; + + while (__ipw2100_tx_process(priv) && i < 200) i++; + + if (i == 200) { + IPW_DEBUG_WARNING( + "%s: Driver is running slow (%d iters).\n", + priv->net_dev->name, i); + } +} + + +static void X__ipw2100_tx_send_commands(struct ipw2100_priv *priv) +{ + struct list_head *element; + struct ipw2100_tx_packet *packet; + struct ipw2100_bd_queue *txq = &priv->tx_queue; + struct ipw2100_bd *tbd; + int next = txq->next; + + while (!list_empty(&priv->msg_pend_list)) { + /* if there isn't enough space in TBD queue, then + * don't stuff a new one in. + * NOTE: 3 are needed as a command will take one, + * and there is a minimum of 2 that must be + * maintained between the r and w indexes + */ + if (txq->available <= 3) { + IPW_DEBUG_TX("no room in tx_queue\n"); + break; + } + + element = priv->msg_pend_list.next; + list_del(element); + DEC_STAT(&priv->msg_pend_stat); + + packet = list_entry(element, + struct ipw2100_tx_packet, list); + + IPW_DEBUG_TX("using TBD at virt=%p, phys=%p\n", + &txq->drv[txq->next], + (void*)(txq->nic + txq->next * + sizeof(struct ipw2100_bd))); + + packet->index = txq->next; + + tbd = &txq->drv[txq->next]; + + /* initialize TBD */ + tbd->host_addr = packet->info.c_struct.cmd_phys; + tbd->buf_length = sizeof(struct ipw2100_cmd_header); + /* not marking number of fragments causes problems + * with f/w debug version */ + tbd->num_fragments = 1; + tbd->status.info.field = + IPW_BD_STATUS_TX_FRAME_COMMAND | + IPW_BD_STATUS_TX_INTERRUPT_ENABLE; + + /* update TBD queue counters */ + txq->next++; + txq->next %= txq->entries; + txq->available--; + DEC_STAT(&priv->txq_stat); + + list_add_tail(element, &priv->fw_pend_list); + INC_STAT(&priv->fw_pend_stat); + } + + if (txq->next != next) { + /* kick off the DMA by notifying firmware the + * write index has moved; make sure TBD stores are sync'd */ + wmb(); + write_register(priv->net_dev, + IPW_MEM_HOST_SHARED_TX_QUEUE_WRITE_INDEX, + txq->next); + } +} + + +/* + * X__ipw2100_tx_send_data + * + */ +static void X__ipw2100_tx_send_data(struct ipw2100_priv *priv) +{ + struct list_head *element; + struct ipw2100_tx_packet *packet; + struct ipw2100_bd_queue *txq = &priv->tx_queue; + struct ipw2100_bd *tbd; + int next = txq->next; + int i = 0; + struct ipw2100_data_header *ipw_hdr; + struct ieee80211_hdr *hdr; + + while (!list_empty(&priv->tx_pend_list)) { + /* if there isn't enough space in TBD queue, then + * don't stuff a new one in. + * NOTE: 4 are needed as a data will take two, + * and there is a minimum of 2 that must be + * maintained between the r and w indexes + */ + element = priv->tx_pend_list.next; + packet = list_entry(element, struct ipw2100_tx_packet, list); + + if (unlikely(1 + packet->info.d_struct.txb->nr_frags > + IPW_MAX_BDS)) { + /* TODO: Support merging buffers if more than + * IPW_MAX_BDS are used */ + IPW_DEBUG_INFO( + "%s: Maximum BD theshold exceeded. " + "Increase fragmentation level.\n", + priv->net_dev->name); + } + + if (txq->available <= 3 + + packet->info.d_struct.txb->nr_frags) { + IPW_DEBUG_TX("no room in tx_queue\n"); + break; + } + + list_del(element); + DEC_STAT(&priv->tx_pend_stat); + + tbd = &txq->drv[txq->next]; + + packet->index = txq->next; + + ipw_hdr = packet->info.d_struct.data; + hdr = (struct ieee80211_hdr *)packet->info.d_struct.txb-> + fragments[0]->data; + + if (priv->ieee->iw_mode == IW_MODE_INFRA) { + /* To DS: Addr1 = BSSID, Addr2 = SA, + Addr3 = DA */ + memcpy(ipw_hdr->src_addr, hdr->addr2, ETH_ALEN); + memcpy(ipw_hdr->dst_addr, hdr->addr3, ETH_ALEN); + } else if (priv->ieee->iw_mode == IW_MODE_ADHOC) { + /* not From/To DS: Addr1 = DA, Addr2 = SA, + Addr3 = BSSID */ + memcpy(ipw_hdr->src_addr, hdr->addr2, ETH_ALEN); + memcpy(ipw_hdr->dst_addr, hdr->addr1, ETH_ALEN); + } + + ipw_hdr->host_command_reg = SEND; + ipw_hdr->host_command_reg1 = 0; + + /* For now we only support host based encryption */ + ipw_hdr->needs_encryption = 0; + ipw_hdr->encrypted = packet->info.d_struct.txb->encrypted; + if (packet->info.d_struct.txb->nr_frags > 1) + ipw_hdr->fragment_size = + packet->info.d_struct.txb->frag_size - IEEE80211_3ADDR_LEN; + else + ipw_hdr->fragment_size = 0; + + tbd->host_addr = packet->info.d_struct.data_phys; + tbd->buf_length = sizeof(struct ipw2100_data_header); + tbd->num_fragments = 1 + packet->info.d_struct.txb->nr_frags; + tbd->status.info.field = + IPW_BD_STATUS_TX_FRAME_802_3 | + IPW_BD_STATUS_TX_FRAME_NOT_LAST_FRAGMENT; + txq->next++; + txq->next %= txq->entries; + + IPW_DEBUG_TX( + "data header tbd TX%d P=%08x L=%d\n", + packet->index, tbd->host_addr, + tbd->buf_length); +#ifdef CONFIG_IPW_DEBUG + if (packet->info.d_struct.txb->nr_frags > 1) + IPW_DEBUG_FRAG("fragment Tx: %d frames\n", + packet->info.d_struct.txb->nr_frags); +#endif + + for (i = 0; i < packet->info.d_struct.txb->nr_frags; i++) { + tbd = &txq->drv[txq->next]; + if (i == packet->info.d_struct.txb->nr_frags - 1) + tbd->status.info.field = + IPW_BD_STATUS_TX_FRAME_802_3 | + IPW_BD_STATUS_TX_INTERRUPT_ENABLE; + else + tbd->status.info.field = + IPW_BD_STATUS_TX_FRAME_802_3 | + IPW_BD_STATUS_TX_FRAME_NOT_LAST_FRAGMENT; + + tbd->buf_length = packet->info.d_struct.txb-> + fragments[i]->len - IEEE80211_3ADDR_LEN; + + tbd->host_addr = pci_map_single( + priv->pci_dev, + packet->info.d_struct.txb->fragments[i]->data + + IEEE80211_3ADDR_LEN, + tbd->buf_length, + PCI_DMA_TODEVICE); + + IPW_DEBUG_TX( + "data frag tbd TX%d P=%08x L=%d\n", + txq->next, tbd->host_addr, tbd->buf_length); + + pci_dma_sync_single_for_device( + priv->pci_dev, tbd->host_addr, + tbd->buf_length, + PCI_DMA_TODEVICE); + + txq->next++; + txq->next %= txq->entries; + } + + txq->available -= 1 + packet->info.d_struct.txb->nr_frags; + SET_STAT(&priv->txq_stat, txq->available); + + list_add_tail(element, &priv->fw_pend_list); + INC_STAT(&priv->fw_pend_stat); + } + + if (txq->next != next) { + /* kick off the DMA by notifying firmware the + * write index has moved; make sure TBD stores are sync'd */ + write_register(priv->net_dev, + IPW_MEM_HOST_SHARED_TX_QUEUE_WRITE_INDEX, + txq->next); + } + return; +} + +static void ipw2100_irq_tasklet(struct ipw2100_priv *priv) +{ + struct net_device *dev = priv->net_dev; + unsigned long flags; + u32 inta, tmp; + + spin_lock_irqsave(&priv->low_lock, flags); + ipw2100_disable_interrupts(priv); + + read_register(dev, IPW_REG_INTA, &inta); + + IPW_DEBUG_ISR("enter - INTA: 0x%08lX\n", + (unsigned long)inta & IPW_INTERRUPT_MASK); + + priv->in_isr++; + priv->interrupts++; + + /* We do not loop and keep polling for more interrupts as this + * is frowned upon and doesn't play nicely with other potentially + * chained IRQs */ + IPW_DEBUG_ISR("INTA: 0x%08lX\n", + (unsigned long)inta & IPW_INTERRUPT_MASK); + + if (inta & IPW2100_INTA_FATAL_ERROR) { + IPW_DEBUG_WARNING(DRV_NAME + ": Fatal interrupt. Scheduling firmware restart.\n"); + priv->inta_other++; + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_FATAL_ERROR); + + read_nic_dword(dev, IPW_NIC_FATAL_ERROR, &priv->fatal_error); + IPW_DEBUG_INFO("%s: Fatal error value: 0x%08X\n", + priv->net_dev->name, priv->fatal_error); + + read_nic_dword(dev, IPW_ERROR_ADDR(priv->fatal_error), &tmp); + IPW_DEBUG_INFO("%s: Fatal error address value: 0x%08X\n", + priv->net_dev->name, tmp); + + /* Wake up any sleeping jobs */ + schedule_reset(priv); + } + + if (inta & IPW2100_INTA_PARITY_ERROR) { + IPW_DEBUG_ERROR("***** PARITY ERROR INTERRUPT !!!! \n"); + priv->inta_other++; + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_PARITY_ERROR); + } + + if (inta & IPW2100_INTA_RX_TRANSFER) { + IPW_DEBUG_ISR("RX interrupt\n"); + + priv->rx_interrupts++; + + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_RX_TRANSFER); + + __ipw2100_rx_process(priv); + __ipw2100_tx_complete(priv); + } + + if (inta & IPW2100_INTA_TX_TRANSFER) { + IPW_DEBUG_ISR("TX interrupt\n"); + + priv->tx_interrupts++; + + write_register(dev, IPW_REG_INTA, + IPW2100_INTA_TX_TRANSFER); + + __ipw2100_tx_complete(priv); + X__ipw2100_tx_send_commands(priv); + X__ipw2100_tx_send_data(priv); + } + + if (inta & IPW2100_INTA_TX_COMPLETE) { + IPW_DEBUG_ISR("TX complete\n"); + priv->inta_other++; + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_TX_COMPLETE); + + __ipw2100_tx_complete(priv); + } + + if (inta & IPW2100_INTA_EVENT_INTERRUPT) { + /* ipw2100_handle_event(dev); */ + priv->inta_other++; + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_EVENT_INTERRUPT); + } + + if (inta & IPW2100_INTA_FW_INIT_DONE) { + IPW_DEBUG_ISR("FW init done interrupt\n"); + priv->inta_other++; + + read_register(dev, IPW_REG_INTA, &tmp); + if (tmp & (IPW2100_INTA_FATAL_ERROR | + IPW2100_INTA_PARITY_ERROR)) { + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_FATAL_ERROR | + IPW2100_INTA_PARITY_ERROR); + } + + write_register(dev, IPW_REG_INTA, + IPW2100_INTA_FW_INIT_DONE); + } + + if (inta & IPW2100_INTA_STATUS_CHANGE) { + IPW_DEBUG_ISR("Status change interrupt\n"); + priv->inta_other++; + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_STATUS_CHANGE); + } + + if (inta & IPW2100_INTA_SLAVE_MODE_HOST_COMMAND_DONE) { + IPW_DEBUG_ISR("slave host mode interrupt\n"); + priv->inta_other++; + write_register( + dev, IPW_REG_INTA, + IPW2100_INTA_SLAVE_MODE_HOST_COMMAND_DONE); + } + + priv->in_isr--; + ipw2100_enable_interrupts(priv); + + spin_unlock_irqrestore(&priv->low_lock, flags); + + IPW_DEBUG_ISR("exit\n"); +} + + +static irqreturn_t ipw2100_interrupt(int irq, void *data, + struct pt_regs *regs) +{ + struct ipw2100_priv *priv = data; + u32 inta, inta_mask; + + if (!data) + return IRQ_NONE; + + spin_lock(&priv->low_lock); + + /* We check to see if we should be ignoring interrupts before + * we touch the hardware. During ucode load if we try and handle + * an interrupt we can cause keyboard problems as well as cause + * the ucode to fail to initialize */ + if (!(priv->status & STATUS_INT_ENABLED)) { + /* Shared IRQ */ + goto none; + } + + read_register(priv->net_dev, IPW_REG_INTA_MASK, &inta_mask); + read_register(priv->net_dev, IPW_REG_INTA, &inta); + + if (inta == 0xFFFFFFFF) { + /* Hardware disappeared */ + IPW_DEBUG_WARNING("IRQ INTA == 0xFFFFFFFF\n"); + goto none; + } + + inta &= IPW_INTERRUPT_MASK; + + if (!(inta & inta_mask)) { + /* Shared interrupt */ + goto none; + } + + /* We disable the hardware interrupt here just to prevent unneeded + * calls to be made. We disable this again within the actual + * work tasklet, so if another part of the code re-enables the + * interrupt, that is fine */ + ipw2100_disable_interrupts(priv); + + tasklet_schedule(&priv->irq_tasklet); + spin_unlock(&priv->low_lock); + + return IRQ_HANDLED; + none: + spin_unlock(&priv->low_lock); + return IRQ_NONE; +} + +static int ipw2100_tx(struct ieee80211_txb *txb, struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct list_head *element; + struct ipw2100_tx_packet *packet; + unsigned long flags; + + spin_lock_irqsave(&priv->low_lock, flags); + + if (!(priv->status & STATUS_ASSOCIATED)) { + IPW_DEBUG_INFO("Can not transmit when not connected.\n"); + priv->ieee->stats.tx_carrier_errors++; + netif_stop_queue(dev); + goto fail_unlock; + } + + if (list_empty(&priv->tx_free_list)) + goto fail_unlock; + + element = priv->tx_free_list.next; + packet = list_entry(element, struct ipw2100_tx_packet, list); + + packet->info.d_struct.txb = txb; + + IPW_DEBUG_TX("Sending fragment (%d bytes):\n", + txb->fragments[0]->len); + printk_buf(IPW_DL_TX, txb->fragments[0]->data, + txb->fragments[0]->len); + + packet->jiffy_start = jiffies; + + list_del(element); + DEC_STAT(&priv->tx_free_stat); + + list_add_tail(element, &priv->tx_pend_list); + INC_STAT(&priv->tx_pend_stat); + + X__ipw2100_tx_send_data(priv); + + spin_unlock_irqrestore(&priv->low_lock, flags); + return 0; + + fail_unlock: + netif_stop_queue(dev); + spin_unlock_irqrestore(&priv->low_lock, flags); + return 1; +} + + +static int ipw2100_msg_allocate(struct ipw2100_priv *priv) +{ + int i, j, err = -EINVAL; + void *v; + dma_addr_t p; + + priv->msg_buffers = (struct ipw2100_tx_packet *)kmalloc( + IPW_COMMAND_POOL_SIZE * sizeof(struct ipw2100_tx_packet), + GFP_KERNEL); + if (!priv->msg_buffers) { + IPW_DEBUG_ERROR("%s: PCI alloc failed for msg " + "buffers.\n", priv->net_dev->name); + return -ENOMEM; + } + + for (i = 0; i < IPW_COMMAND_POOL_SIZE; i++) { + v = pci_alloc_consistent( + priv->pci_dev, + sizeof(struct ipw2100_cmd_header), + &p); + if (!v) { + IPW_DEBUG_ERROR( + "%s: PCI alloc failed for msg " + "buffers.\n", + priv->net_dev->name); + err = -ENOMEM; + break; + } + + memset(v, 0, sizeof(struct ipw2100_cmd_header)); + + priv->msg_buffers[i].type = COMMAND; + priv->msg_buffers[i].info.c_struct.cmd = + (struct ipw2100_cmd_header*)v; + priv->msg_buffers[i].info.c_struct.cmd_phys = p; + } + + if (i == IPW_COMMAND_POOL_SIZE) + return 0; + + for (j = 0; j < i; j++) { + pci_free_consistent( + priv->pci_dev, + sizeof(struct ipw2100_cmd_header), + priv->msg_buffers[j].info.c_struct.cmd, + priv->msg_buffers[j].info.c_struct.cmd_phys); + } + + kfree(priv->msg_buffers); + priv->msg_buffers = NULL; + + return err; +} + +static int ipw2100_msg_initialize(struct ipw2100_priv *priv) +{ + int i; + + INIT_LIST_HEAD(&priv->msg_free_list); + INIT_LIST_HEAD(&priv->msg_pend_list); + + for (i = 0; i < IPW_COMMAND_POOL_SIZE; i++) + list_add_tail(&priv->msg_buffers[i].list, &priv->msg_free_list); + SET_STAT(&priv->msg_free_stat, i); + + return 0; +} + +static void ipw2100_msg_free(struct ipw2100_priv *priv) +{ + int i; + + if (!priv->msg_buffers) + return; + + for (i = 0; i < IPW_COMMAND_POOL_SIZE; i++) { + pci_free_consistent(priv->pci_dev, + sizeof(struct ipw2100_cmd_header), + priv->msg_buffers[i].info.c_struct.cmd, + priv->msg_buffers[i].info.c_struct.cmd_phys); + } + + kfree(priv->msg_buffers); + priv->msg_buffers = NULL; +} + +static ssize_t show_pci(struct device *d, char *buf) +{ + struct pci_dev *pci_dev = container_of(d, struct pci_dev, dev); + char *out = buf; + int i, j; + u32 val; + + for (i = 0; i < 16; i++) { + out += sprintf(out, "[%08X] ", i * 16); + for (j = 0; j < 16; j += 4) { + pci_read_config_dword(pci_dev, i * 16 + j, &val); + out += sprintf(out, "%08X ", val); + } + out += sprintf(out, "\n"); + } + + return out - buf; +} +static DEVICE_ATTR(pci, S_IRUGO, show_pci, NULL); + +static ssize_t show_cfg(struct device *d, char *buf) +{ + struct ipw2100_priv *p = (struct ipw2100_priv *)d->driver_data; + return sprintf(buf, "0x%08x\n", (int)p->config); +} +static DEVICE_ATTR(cfg, S_IRUGO, show_cfg, NULL); + +static ssize_t show_status(struct device *d, char *buf) +{ + struct ipw2100_priv *p = (struct ipw2100_priv *)d->driver_data; + return sprintf(buf, "0x%08x\n", (int)p->status); +} +static DEVICE_ATTR(status, S_IRUGO, show_status, NULL); + +static ssize_t show_capability(struct device *d, char *buf) +{ + struct ipw2100_priv *p = (struct ipw2100_priv *)d->driver_data; + return sprintf(buf, "0x%08x\n", (int)p->capability); +} +static DEVICE_ATTR(capability, S_IRUGO, show_capability, NULL); + + +#define IPW2100_REG(x) { IPW_ ##x, #x } +const struct { + u32 addr; + const char *name; +} hw_data[] = { + IPW2100_REG(REG_GP_CNTRL), + IPW2100_REG(REG_GPIO), + IPW2100_REG(REG_INTA), + IPW2100_REG(REG_INTA_MASK), + IPW2100_REG(REG_RESET_REG), +}; +#define IPW2100_NIC(x, s) { x, #x, s } +const struct { + u32 addr; + const char *name; + size_t size; +} nic_data[] = { + IPW2100_NIC(IPW2100_CONTROL_REG, 2), + IPW2100_NIC(0x210014, 1), + IPW2100_NIC(0x210000, 1), +}; +#define IPW2100_ORD(x, d) { IPW_ORD_ ##x, #x, d } +const struct { + u8 index; + const char *name; + const char *desc; +} ord_data[] = { + IPW2100_ORD(STAT_TX_HOST_REQUESTS, "requested Host Tx's (MSDU)"), + IPW2100_ORD(STAT_TX_HOST_COMPLETE, "successful Host Tx's (MSDU)"), + IPW2100_ORD(STAT_TX_DIR_DATA, "successful Directed Tx's (MSDU)"), + IPW2100_ORD(STAT_TX_DIR_DATA1, "successful Directed Tx's (MSDU) @ 1MB"), + IPW2100_ORD(STAT_TX_DIR_DATA2, "successful Directed Tx's (MSDU) @ 2MB"), + IPW2100_ORD(STAT_TX_DIR_DATA5_5, "successful Directed Tx's (MSDU) @ 5_5MB"), + IPW2100_ORD(STAT_TX_DIR_DATA11, "successful Directed Tx's (MSDU) @ 11MB"), + IPW2100_ORD(STAT_TX_NODIR_DATA1, "successful Non_Directed Tx's (MSDU) @ 1MB"), + IPW2100_ORD(STAT_TX_NODIR_DATA2, "successful Non_Directed Tx's (MSDU) @ 2MB"), + IPW2100_ORD(STAT_TX_NODIR_DATA5_5, "successful Non_Directed Tx's (MSDU) @ 5.5MB"), + IPW2100_ORD(STAT_TX_NODIR_DATA11, "successful Non_Directed Tx's (MSDU) @ 11MB"), + IPW2100_ORD(STAT_NULL_DATA, "successful NULL data Tx's"), + IPW2100_ORD(STAT_TX_RTS, "successful Tx RTS"), + IPW2100_ORD(STAT_TX_CTS, "successful Tx CTS"), + IPW2100_ORD(STAT_TX_ACK, "successful Tx ACK"), + IPW2100_ORD(STAT_TX_ASSN, "successful Association Tx's"), + IPW2100_ORD(STAT_TX_ASSN_RESP, "successful Association response Tx's"), + IPW2100_ORD(STAT_TX_REASSN, "successful Reassociation Tx's"), + IPW2100_ORD(STAT_TX_REASSN_RESP, "successful Reassociation response Tx's"), + IPW2100_ORD(STAT_TX_PROBE, "probes successfully transmitted"), + IPW2100_ORD(STAT_TX_PROBE_RESP, "probe responses successfully transmitted"), + IPW2100_ORD(STAT_TX_BEACON, "tx beacon"), + IPW2100_ORD(STAT_TX_ATIM, "Tx ATIM"), + IPW2100_ORD(STAT_TX_DISASSN, "successful Disassociation TX"), + IPW2100_ORD(STAT_TX_AUTH, "successful Authentication Tx"), + IPW2100_ORD(STAT_TX_DEAUTH, "successful Deauthentication TX"), + IPW2100_ORD(STAT_TX_TOTAL_BYTES, "Total successful Tx data bytes"), + IPW2100_ORD(STAT_TX_RETRIES, "Tx retries"), + IPW2100_ORD(STAT_TX_RETRY1, "Tx retries at 1MBPS"), + IPW2100_ORD(STAT_TX_RETRY2, "Tx retries at 2MBPS"), + IPW2100_ORD(STAT_TX_RETRY5_5, "Tx retries at 5.5MBPS"), + IPW2100_ORD(STAT_TX_RETRY11, "Tx retries at 11MBPS"), + IPW2100_ORD(STAT_TX_FAILURES, "Tx Failures"), + IPW2100_ORD(STAT_TX_MAX_TRIES_IN_HOP,"times max tries in a hop failed"), + IPW2100_ORD(STAT_TX_DISASSN_FAIL, "times disassociation failed"), + IPW2100_ORD(STAT_TX_ERR_CTS, "missed/bad CTS frames"), + IPW2100_ORD(STAT_TX_ERR_ACK, "tx err due to acks"), + IPW2100_ORD(STAT_RX_HOST, "packets passed to host"), + IPW2100_ORD(STAT_RX_DIR_DATA, "directed packets"), + IPW2100_ORD(STAT_RX_DIR_DATA1, "directed packets at 1MB"), + IPW2100_ORD(STAT_RX_DIR_DATA2, "directed packets at 2MB"), + IPW2100_ORD(STAT_RX_DIR_DATA5_5, "directed packets at 5.5MB"), + IPW2100_ORD(STAT_RX_DIR_DATA11, "directed packets at 11MB"), + IPW2100_ORD(STAT_RX_NODIR_DATA,"nondirected packets"), + IPW2100_ORD(STAT_RX_NODIR_DATA1, "nondirected packets at 1MB"), + IPW2100_ORD(STAT_RX_NODIR_DATA2, "nondirected packets at 2MB"), + IPW2100_ORD(STAT_RX_NODIR_DATA5_5, "nondirected packets at 5.5MB"), + IPW2100_ORD(STAT_RX_NODIR_DATA11, "nondirected packets at 11MB"), + IPW2100_ORD(STAT_RX_NULL_DATA, "null data rx's"), + IPW2100_ORD(STAT_RX_RTS, "Rx RTS"), + IPW2100_ORD(STAT_RX_CTS, "Rx CTS"), + IPW2100_ORD(STAT_RX_ACK, "Rx ACK"), + IPW2100_ORD(STAT_RX_CFEND, "Rx CF End"), + IPW2100_ORD(STAT_RX_CFEND_ACK, "Rx CF End + CF Ack"), + IPW2100_ORD(STAT_RX_ASSN, "Association Rx's"), + IPW2100_ORD(STAT_RX_ASSN_RESP, "Association response Rx's"), + IPW2100_ORD(STAT_RX_REASSN, "Reassociation Rx's"), + IPW2100_ORD(STAT_RX_REASSN_RESP, "Reassociation response Rx's"), + IPW2100_ORD(STAT_RX_PROBE, "probe Rx's"), + IPW2100_ORD(STAT_RX_PROBE_RESP, "probe response Rx's"), + IPW2100_ORD(STAT_RX_BEACON, "Rx beacon"), + IPW2100_ORD(STAT_RX_ATIM, "Rx ATIM"), + IPW2100_ORD(STAT_RX_DISASSN, "disassociation Rx"), + IPW2100_ORD(STAT_RX_AUTH, "authentication Rx"), + IPW2100_ORD(STAT_RX_DEAUTH, "deauthentication Rx"), + IPW2100_ORD(STAT_RX_TOTAL_BYTES,"Total rx data bytes received"), + IPW2100_ORD(STAT_RX_ERR_CRC, "packets with Rx CRC error"), + IPW2100_ORD(STAT_RX_ERR_CRC1, "Rx CRC errors at 1MB"), + IPW2100_ORD(STAT_RX_ERR_CRC2, "Rx CRC errors at 2MB"), + IPW2100_ORD(STAT_RX_ERR_CRC5_5, "Rx CRC errors at 5.5MB"), + IPW2100_ORD(STAT_RX_ERR_CRC11, "Rx CRC errors at 11MB"), + IPW2100_ORD(STAT_RX_DUPLICATE1, "duplicate rx packets at 1MB"), + IPW2100_ORD(STAT_RX_DUPLICATE2, "duplicate rx packets at 2MB"), + IPW2100_ORD(STAT_RX_DUPLICATE5_5, "duplicate rx packets at 5.5MB"), + IPW2100_ORD(STAT_RX_DUPLICATE11, "duplicate rx packets at 11MB"), + IPW2100_ORD(STAT_RX_DUPLICATE, "duplicate rx packets"), + IPW2100_ORD(PERS_DB_LOCK, "locking fw permanent db"), + IPW2100_ORD(PERS_DB_SIZE, "size of fw permanent db"), + IPW2100_ORD(PERS_DB_ADDR, "address of fw permanent db"), + IPW2100_ORD(STAT_RX_INVALID_PROTOCOL, "rx frames with invalid protocol"), + IPW2100_ORD(SYS_BOOT_TIME, "Boot time"), + IPW2100_ORD(STAT_RX_NO_BUFFER, "rx frames rejected due to no buffer"), + IPW2100_ORD(STAT_RX_MISSING_FRAG, "rx frames dropped due to missing fragment"), + IPW2100_ORD(STAT_RX_ORPHAN_FRAG, "rx frames dropped due to non-sequential fragment"), + IPW2100_ORD(STAT_RX_ORPHAN_FRAME, "rx frames dropped due to unmatched 1st frame"), + IPW2100_ORD(STAT_RX_FRAG_AGEOUT, "rx frames dropped due to uncompleted frame"), + IPW2100_ORD(STAT_RX_ICV_ERRORS, "ICV errors during decryption"), + IPW2100_ORD(STAT_PSP_SUSPENSION,"times adapter suspended"), + IPW2100_ORD(STAT_PSP_BCN_TIMEOUT, "beacon timeout"), + IPW2100_ORD(STAT_PSP_POLL_TIMEOUT, "poll response timeouts"), + IPW2100_ORD(STAT_PSP_NONDIR_TIMEOUT, "timeouts waiting for last {broad,multi}cast pkt"), + IPW2100_ORD(STAT_PSP_RX_DTIMS, "PSP DTIMs received"), + IPW2100_ORD(STAT_PSP_RX_TIMS, "PSP TIMs received"), + IPW2100_ORD(STAT_PSP_STATION_ID,"PSP Station ID"), + IPW2100_ORD(LAST_ASSN_TIME, "RTC time of last association"), + IPW2100_ORD(STAT_PERCENT_MISSED_BCNS,"current calculation of % missed beacons"), + IPW2100_ORD(STAT_PERCENT_RETRIES,"current calculation of % missed tx retries"), + IPW2100_ORD(ASSOCIATED_AP_PTR, "0 if not associated, else pointer to AP table entry"), + IPW2100_ORD(AVAILABLE_AP_CNT, "AP's decsribed in the AP table"), + IPW2100_ORD(AP_LIST_PTR, "Ptr to list of available APs"), + IPW2100_ORD(STAT_AP_ASSNS, "associations"), + IPW2100_ORD(STAT_ASSN_FAIL, "association failures"), + IPW2100_ORD(STAT_ASSN_RESP_FAIL,"failures due to response fail"), + IPW2100_ORD(STAT_FULL_SCANS, "full scans"), + IPW2100_ORD(CARD_DISABLED, "Card Disabled"), + IPW2100_ORD(STAT_ROAM_INHIBIT, "times roaming was inhibited due to activity"), + IPW2100_ORD(RSSI_AT_ASSN, "RSSI of associated AP at time of association"), + IPW2100_ORD(STAT_ASSN_CAUSE1, "reassociation: no probe response or TX on hop"), + IPW2100_ORD(STAT_ASSN_CAUSE2, "reassociation: poor tx/rx quality"), + IPW2100_ORD(STAT_ASSN_CAUSE3, "reassociation: tx/rx quality (excessive AP load"), + IPW2100_ORD(STAT_ASSN_CAUSE4, "reassociation: AP RSSI level"), + IPW2100_ORD(STAT_ASSN_CAUSE5, "reassociations due to load leveling"), + IPW2100_ORD(STAT_AUTH_FAIL, "times authentication failed"), + IPW2100_ORD(STAT_AUTH_RESP_FAIL,"times authentication response failed"), + IPW2100_ORD(STATION_TABLE_CNT, "entries in association table"), + IPW2100_ORD(RSSI_AVG_CURR, "Current avg RSSI"), + IPW2100_ORD(POWER_MGMT_MODE, "Power mode - 0=CAM, 1=PSP"), + IPW2100_ORD(COUNTRY_CODE, "IEEE country code as recv'd from beacon"), + IPW2100_ORD(COUNTRY_CHANNELS, "channels suported by country"), + IPW2100_ORD(RESET_CNT, "adapter resets (warm)"), + IPW2100_ORD(BEACON_INTERVAL, "Beacon interval"), + IPW2100_ORD(ANTENNA_DIVERSITY, "TRUE if antenna diversity is disabled"), + IPW2100_ORD(DTIM_PERIOD, "beacon intervals between DTIMs"), + IPW2100_ORD(OUR_FREQ, "current radio freq lower digits - channel ID"), + IPW2100_ORD(RTC_TIME, "current RTC time"), + IPW2100_ORD(PORT_TYPE, "operating mode"), + IPW2100_ORD(CURRENT_TX_RATE, "current tx rate"), + IPW2100_ORD(SUPPORTED_RATES, "supported tx rates"), + IPW2100_ORD(ATIM_WINDOW, "current ATIM Window"), + IPW2100_ORD(BASIC_RATES, "basic tx rates"), + IPW2100_ORD(NIC_HIGHEST_RATE, "NIC highest tx rate"), + IPW2100_ORD(AP_HIGHEST_RATE, "AP highest tx rate"), + IPW2100_ORD(CAPABILITIES, "Management frame capability field"), + IPW2100_ORD(AUTH_TYPE, "Type of authentication"), + IPW2100_ORD(RADIO_TYPE, "Adapter card platform type"), + IPW2100_ORD(RTS_THRESHOLD, "Min packet length for RTS handshaking"), + IPW2100_ORD(INT_MODE, "International mode"), + IPW2100_ORD(FRAGMENTATION_THRESHOLD, "protocol frag threshold"), + IPW2100_ORD(EEPROM_SRAM_DB_BLOCK_START_ADDRESS, "EEPROM offset in SRAM"), + IPW2100_ORD(EEPROM_SRAM_DB_BLOCK_SIZE, "EEPROM size in SRAM"), + IPW2100_ORD(EEPROM_SKU_CAPABILITY, "EEPROM SKU Capability"), + IPW2100_ORD(EEPROM_IBSS_11B_CHANNELS, "EEPROM IBSS 11b channel set"), + IPW2100_ORD(MAC_VERSION, "MAC Version"), + IPW2100_ORD(MAC_REVISION, "MAC Revision"), + IPW2100_ORD(RADIO_VERSION, "Radio Version"), + IPW2100_ORD(NIC_MANF_DATE_TIME, "MANF Date/Time STAMP"), + IPW2100_ORD(UCODE_VERSION, "Ucode Version"), +}; + + +static ssize_t show_registers(struct device *d, char *buf) +{ + int i; + struct ipw2100_priv *priv = dev_get_drvdata(d); + struct net_device *dev = priv->net_dev; + char * out = buf; + u32 val = 0; + + out += sprintf(out, "%30s [Address ] : Hex\n", "Register"); + + for (i = 0; i < (sizeof(hw_data) / sizeof(*hw_data)); i++) { + read_register(dev, hw_data[i].addr, &val); + out += sprintf(out, "%30s [%08X] : %08X\n", + hw_data[i].name, hw_data[i].addr, val); + } + + return out - buf; +} +static DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL); + + +static ssize_t show_hardware(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + struct net_device *dev = priv->net_dev; + char * out = buf; + int i; + + out += sprintf(out, "%30s [Address ] : Hex\n", "NIC entry"); + + for (i = 0; i < (sizeof(nic_data) / sizeof(*nic_data)); i++) { + u8 tmp8; + u16 tmp16; + u32 tmp32; + + switch (nic_data[i].size) { + case 1: + read_nic_byte(dev, nic_data[i].addr, &tmp8); + out += sprintf(out, "%30s [%08X] : %02X\n", + nic_data[i].name, nic_data[i].addr, + tmp8); + break; + case 2: + read_nic_word(dev, nic_data[i].addr, &tmp16); + out += sprintf(out, "%30s [%08X] : %04X\n", + nic_data[i].name, nic_data[i].addr, + tmp16); + break; + case 4: + read_nic_dword(dev, nic_data[i].addr, &tmp32); + out += sprintf(out, "%30s [%08X] : %08X\n", + nic_data[i].name, nic_data[i].addr, + tmp32); + break; + } + } + return out - buf; +} +static DEVICE_ATTR(hardware, S_IRUGO, show_hardware, NULL); + + +static ssize_t show_memory(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + struct net_device *dev = priv->net_dev; + static unsigned long loop = 0; + int len = 0; + u32 buffer[4]; + int i; + char line[81]; + + if (loop >= 0x30000) + loop = 0; + + /* sysfs provides us PAGE_SIZE buffer */ + while (len < PAGE_SIZE - 128 && loop < 0x30000) { + + if (priv->snapshot[0]) for (i = 0; i < 4; i++) + buffer[i] = *(u32 *)SNAPSHOT_ADDR(loop + i * 4); + else for (i = 0; i < 4; i++) + read_nic_dword(dev, loop + i * 4, &buffer[i]); + + if (priv->dump_raw) + len += sprintf(buf + len, + "%c%c%c%c" + "%c%c%c%c" + "%c%c%c%c" + "%c%c%c%c", + ((u8*)buffer)[0x0], + ((u8*)buffer)[0x1], + ((u8*)buffer)[0x2], + ((u8*)buffer)[0x3], + ((u8*)buffer)[0x4], + ((u8*)buffer)[0x5], + ((u8*)buffer)[0x6], + ((u8*)buffer)[0x7], + ((u8*)buffer)[0x8], + ((u8*)buffer)[0x9], + ((u8*)buffer)[0xa], + ((u8*)buffer)[0xb], + ((u8*)buffer)[0xc], + ((u8*)buffer)[0xd], + ((u8*)buffer)[0xe], + ((u8*)buffer)[0xf]); + else + len += sprintf(buf + len, "%s\n", + snprint_line(line, sizeof(line), + (u8*)buffer, 16, loop)); + loop += 16; + } + + return len; +} + +static ssize_t store_memory(struct device *d, const char *buf, size_t count) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + struct net_device *dev = priv->net_dev; + const char *p = buf; + + if (count < 1) + return count; + + if (p[0] == '1' || + (count >= 2 && tolower(p[0]) == 'o' && tolower(p[1]) == 'n')) { + IPW_DEBUG_INFO("%s: Setting memory dump to RAW mode.\n", + dev->name); + priv->dump_raw = 1; + + } else if (p[0] == '0' || (count >= 2 && tolower(p[0]) == 'o' && + tolower(p[1]) == 'f')) { + IPW_DEBUG_INFO("%s: Setting memory dump to HEX mode.\n", + dev->name); + priv->dump_raw = 0; + + } else if (tolower(p[0]) == 'r') { + IPW_DEBUG_INFO("%s: Resetting firmware snapshot.\n", + dev->name); + ipw2100_snapshot_free(priv); + + } else + IPW_DEBUG_INFO("%s: Usage: 0|on = HEX, 1|off = RAW, " + "reset = clear memory snapshot\n", + dev->name); + + return count; +} +static DEVICE_ATTR(memory, S_IWUSR|S_IRUGO, show_memory, store_memory); + + +static ssize_t show_ordinals(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + u32 val = 0; + int len = 0; + u32 val_len; + static int loop = 0; + + if (loop >= sizeof(ord_data) / sizeof(*ord_data)) + loop = 0; + + /* sysfs provides us PAGE_SIZE buffer */ + while (len < PAGE_SIZE - 128 && + loop < (sizeof(ord_data) / sizeof(*ord_data))) { + + val_len = sizeof(u32); + + if (ipw2100_get_ordinal(priv, ord_data[loop].index, &val, + &val_len)) + len += sprintf(buf + len, "[0x%02X] = ERROR %s\n", + ord_data[loop].index, + ord_data[loop].desc); + else + len += sprintf(buf + len, "[0x%02X] = 0x%08X %s\n", + ord_data[loop].index, val, + ord_data[loop].desc); + loop++; + } + + return len; +} +static DEVICE_ATTR(ordinals, S_IRUGO, show_ordinals, NULL); + + +static ssize_t show_stats(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + char * out = buf; + + out += sprintf(out, "interrupts: %d {tx: %d, rx: %d, other: %d}\n", + priv->interrupts, priv->tx_interrupts, + priv->rx_interrupts, priv->inta_other); + out += sprintf(out, "firmware resets: %d\n", priv->resets); + out += sprintf(out, "firmware hangs: %d\n", priv->hangs); +#ifdef CONFIG_IPW_DEBUG + out += sprintf(out, "packet mismatch image: %s\n", + priv->snapshot[0] ? "YES" : "NO"); +#endif + + return out - buf; +} +static DEVICE_ATTR(stats, S_IRUGO, show_stats, NULL); + + +int ipw2100_switch_mode(struct ipw2100_priv *priv, u32 mode) +{ + int err; + + if (mode == priv->ieee->iw_mode) + return 0; + + err = ipw2100_disable_adapter(priv); + if (err) { + IPW_DEBUG_ERROR("%s: Could not disable adapter %d\n", + priv->net_dev->name, err); + return err; + } + + switch (mode) { + case IW_MODE_INFRA: + priv->net_dev->type = ARPHRD_ETHER; + break; + case IW_MODE_ADHOC: + priv->net_dev->type = ARPHRD_ETHER; + break; +#ifdef CONFIG_IPW2100_MONITOR + case IW_MODE_MONITOR: + priv->last_mode = priv->ieee->iw_mode; + priv->net_dev->type = ARPHRD_IEEE80211; + break; +#endif /* CONFIG_IPW2100_MONITOR */ + } + + priv->ieee->iw_mode = mode; + +#ifdef CONFIG_PM + /* Indicate ipw2100_download_firmware download firmware + * from disk instead of memory. */ + ipw2100_firmware.version = 0; +#endif + + printk(KERN_INFO "%s: Reseting on mode change.\n", + priv->net_dev->name); + priv->reset_backoff = 0; + schedule_reset(priv); + + return 0; +} + +static ssize_t show_internals(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + int len = 0; + +#define DUMP_VAR(x,y) len += sprintf(buf + len, # x ": %" # y "\n", priv-> x) + + if (priv->status & STATUS_ASSOCIATED) + len += sprintf(buf + len, "connected: %lu\n", + get_seconds() - priv->connect_start); + else + len += sprintf(buf + len, "not connected\n"); + + DUMP_VAR(ieee->crypt[priv->ieee->tx_keyidx], p); + DUMP_VAR(status, 08lx); + DUMP_VAR(config, 08lx); + DUMP_VAR(capability, 08lx); + + len += sprintf(buf + len, "last_rtc: %lu\n", (unsigned long)priv->last_rtc); + + DUMP_VAR(fatal_error, d); + DUMP_VAR(stop_hang_check, d); + DUMP_VAR(stop_rf_kill, d); + DUMP_VAR(messages_sent, d); + + DUMP_VAR(tx_pend_stat.value, d); + DUMP_VAR(tx_pend_stat.hi, d); + + DUMP_VAR(tx_free_stat.value, d); + DUMP_VAR(tx_free_stat.lo, d); + + DUMP_VAR(msg_free_stat.value, d); + DUMP_VAR(msg_free_stat.lo, d); + + DUMP_VAR(msg_pend_stat.value, d); + DUMP_VAR(msg_pend_stat.hi, d); + + DUMP_VAR(fw_pend_stat.value, d); + DUMP_VAR(fw_pend_stat.hi, d); + + DUMP_VAR(txq_stat.value, d); + DUMP_VAR(txq_stat.lo, d); + + DUMP_VAR(ieee->scans, d); + DUMP_VAR(reset_backoff, d); + + return len; +} +static DEVICE_ATTR(internals, S_IRUGO, show_internals, NULL); + + +static ssize_t show_bssinfo(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + char essid[IW_ESSID_MAX_SIZE + 1]; + u8 bssid[ETH_ALEN]; + u32 chan = 0; + char * out = buf; + int length; + int ret; + + memset(essid, 0, sizeof(essid)); + memset(bssid, 0, sizeof(bssid)); + + length = IW_ESSID_MAX_SIZE; + ret = ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_SSID, essid, &length); + if (ret) + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + + length = sizeof(bssid); + ret = ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_AP_BSSID, + bssid, &length); + if (ret) + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + + length = sizeof(u32); + ret = ipw2100_get_ordinal(priv, IPW_ORD_OUR_FREQ, &chan, &length); + if (ret) + IPW_DEBUG_INFO("failed querying ordinals at line %d\n", + __LINE__); + + out += sprintf(out, "ESSID: %s\n", essid); + out += sprintf(out, "BSSID: %02x:%02x:%02x:%02x:%02x:%02x\n", + bssid[0], bssid[1], bssid[2], + bssid[3], bssid[4], bssid[5]); + out += sprintf(out, "Channel: %d\n", chan); + + return out - buf; +} +static DEVICE_ATTR(bssinfo, S_IRUGO, show_bssinfo, NULL); + + + + +#ifdef CONFIG_IPW_DEBUG +static ssize_t show_debug_level(struct device_driver *d, char *buf) +{ + return sprintf(buf, "0x%08X\n", ipw2100_debug_level); +} + +static ssize_t store_debug_level(struct device_driver *d, const char *buf, + size_t count) +{ + char *p = (char *)buf; + u32 val; + + if (p[1] == 'x' || p[1] == 'X' || p[0] == 'x' || p[0] == 'X') { + p++; + if (p[0] == 'x' || p[0] == 'X') + p++; + val = simple_strtoul(p, &p, 16); + } else + val = simple_strtoul(p, &p, 10); + if (p == buf) + IPW_DEBUG_INFO(DRV_NAME + ": %s is not in hex or decimal form.\n", buf); + else + ipw2100_debug_level = val; + + return strnlen(buf, count); +} +static DRIVER_ATTR(debug_level, S_IWUSR | S_IRUGO, show_debug_level, + store_debug_level); +#endif /* CONFIG_IPW_DEBUG */ + + +static ssize_t show_fatal_error(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + char *out = buf; + int i; + + if (priv->fatal_error) + out += sprintf(out, "0x%08X\n", + priv->fatal_error); + else + out += sprintf(out, "0\n"); + + for (i = 1; i <= IPW2100_ERROR_QUEUE; i++) { + if (!priv->fatal_errors[(priv->fatal_index - i) % + IPW2100_ERROR_QUEUE]) + continue; + + out += sprintf(out, "%d. 0x%08X\n", i, + priv->fatal_errors[(priv->fatal_index - i) % + IPW2100_ERROR_QUEUE]); + } + + return out - buf; +} + +static ssize_t store_fatal_error(struct device *d, const char *buf, + size_t count) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + schedule_reset(priv); + return count; +} +static DEVICE_ATTR(fatal_error, S_IWUSR|S_IRUGO, show_fatal_error, store_fatal_error); + + +static ssize_t show_scan_age(struct device *d, char *buf) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + return sprintf(buf, "%d\n", priv->ieee->scan_age); +} + +static ssize_t store_scan_age(struct device *d, const char *buf, size_t count) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + struct net_device *dev = priv->net_dev; + char buffer[] = "00000000"; + unsigned long len = + (sizeof(buffer) - 1) > count ? count : sizeof(buffer) - 1; + unsigned long val; + char *p = buffer; + + IPW_DEBUG_INFO("enter\n"); + + strncpy(buffer, buf, len); + buffer[len] = 0; + + if (p[1] == 'x' || p[1] == 'X' || p[0] == 'x' || p[0] == 'X') { + p++; + if (p[0] == 'x' || p[0] == 'X') + p++; + val = simple_strtoul(p, &p, 16); + } else + val = simple_strtoul(p, &p, 10); + if (p == buffer) { + IPW_DEBUG_INFO("%s: user supplied invalid value.\n", + dev->name); + } else { + priv->ieee->scan_age = val; + IPW_DEBUG_INFO("set scan_age = %u\n", priv->ieee->scan_age); + } + + IPW_DEBUG_INFO("exit\n"); + return len; +} +static DEVICE_ATTR(scan_age, S_IWUSR | S_IRUGO, show_scan_age, store_scan_age); + + +static ssize_t show_rf_kill(struct device *d, char *buf) +{ + /* 0 - RF kill not enabled + 1 - SW based RF kill active (sysfs) + 2 - HW based RF kill active + 3 - Both HW and SW baed RF kill active */ + struct ipw2100_priv *priv = (struct ipw2100_priv *)d->driver_data; + int val = ((priv->status & STATUS_RF_KILL_SW) ? 0x1 : 0x0) | + (rf_kill_active(priv) ? 0x2 : 0x0); + return sprintf(buf, "%i\n", val); +} + +static int ipw_radio_kill_sw(struct ipw2100_priv *priv, int disable_radio) +{ + if ((disable_radio ? 1 : 0) == + (priv->status & STATUS_RF_KILL_SW ? 1 : 0)) + return 0 ; + + IPW_DEBUG_RF_KILL("Manual SW RF Kill set to: RADIO %s\n", + disable_radio ? "OFF" : "ON"); + + down(&priv->action_sem); + + if (disable_radio) { + priv->status |= STATUS_RF_KILL_SW; + ipw2100_down(priv); + } else { + priv->status &= ~STATUS_RF_KILL_SW; + if (rf_kill_active(priv)) { + IPW_DEBUG_RF_KILL("Can not turn radio back on - " + "disabled by HW switch\n"); + /* Make sure the RF_KILL check timer is running */ + priv->stop_rf_kill = 0; + cancel_delayed_work(&priv->rf_kill); + queue_delayed_work(priv->workqueue, &priv->rf_kill, + HZ); + } else + schedule_reset(priv); + } + + up(&priv->action_sem); + return 1; +} + +static ssize_t store_rf_kill(struct device *d, const char *buf, size_t count) +{ + struct ipw2100_priv *priv = dev_get_drvdata(d); + ipw_radio_kill_sw(priv, buf[0] == '1'); + return count; +} +static DEVICE_ATTR(rf_kill, S_IWUSR|S_IRUGO, show_rf_kill, store_rf_kill); + + +static struct attribute *ipw2100_sysfs_entries[] = { + &dev_attr_hardware.attr, + &dev_attr_registers.attr, + &dev_attr_ordinals.attr, + &dev_attr_pci.attr, + &dev_attr_stats.attr, + &dev_attr_internals.attr, + &dev_attr_bssinfo.attr, + &dev_attr_memory.attr, + &dev_attr_scan_age.attr, + &dev_attr_fatal_error.attr, + &dev_attr_rf_kill.attr, + &dev_attr_cfg.attr, + &dev_attr_status.attr, + &dev_attr_capability.attr, + NULL, +}; + +static struct attribute_group ipw2100_attribute_group = { + .attrs = ipw2100_sysfs_entries, +}; + + +static int status_queue_allocate(struct ipw2100_priv *priv, int entries) +{ + struct ipw2100_status_queue *q = &priv->status_queue; + + IPW_DEBUG_INFO("enter\n"); + + q->size = entries * sizeof(struct ipw2100_status); + q->drv = (struct ipw2100_status *)pci_alloc_consistent( + priv->pci_dev, q->size, &q->nic); + if (!q->drv) { + IPW_DEBUG_WARNING( + "Can not allocate status queue.\n"); + return -ENOMEM; + } + + memset(q->drv, 0, q->size); + + IPW_DEBUG_INFO("exit\n"); + + return 0; +} + +static void status_queue_free(struct ipw2100_priv *priv) +{ + IPW_DEBUG_INFO("enter\n"); + + if (priv->status_queue.drv) { + pci_free_consistent( + priv->pci_dev, priv->status_queue.size, + priv->status_queue.drv, priv->status_queue.nic); + priv->status_queue.drv = NULL; + } + + IPW_DEBUG_INFO("exit\n"); +} + +static int bd_queue_allocate(struct ipw2100_priv *priv, + struct ipw2100_bd_queue *q, int entries) +{ + IPW_DEBUG_INFO("enter\n"); + + memset(q, 0, sizeof(struct ipw2100_bd_queue)); + + q->entries = entries; + q->size = entries * sizeof(struct ipw2100_bd); + q->drv = pci_alloc_consistent(priv->pci_dev, q->size, &q->nic); + if (!q->drv) { + IPW_DEBUG_INFO("can't allocate shared memory for buffer descriptors\n"); + return -ENOMEM; + } + memset(q->drv, 0, q->size); + + IPW_DEBUG_INFO("exit\n"); + + return 0; +} + +static void bd_queue_free(struct ipw2100_priv *priv, + struct ipw2100_bd_queue *q) +{ + IPW_DEBUG_INFO("enter\n"); + + if (!q) + return; + + if (q->drv) { + pci_free_consistent(priv->pci_dev, + q->size, q->drv, q->nic); + q->drv = NULL; + } + + IPW_DEBUG_INFO("exit\n"); +} + +static void bd_queue_initialize( + struct ipw2100_priv *priv, struct ipw2100_bd_queue * q, + u32 base, u32 size, u32 r, u32 w) +{ + IPW_DEBUG_INFO("enter\n"); + + IPW_DEBUG_INFO("initializing bd queue at virt=%p, phys=%08x\n", q->drv, q->nic); + + write_register(priv->net_dev, base, q->nic); + write_register(priv->net_dev, size, q->entries); + write_register(priv->net_dev, r, q->oldest); + write_register(priv->net_dev, w, q->next); + + IPW_DEBUG_INFO("exit\n"); +} + +static void ipw2100_kill_workqueue(struct ipw2100_priv *priv) +{ + if (priv->workqueue) { + priv->stop_rf_kill = 1; + priv->stop_hang_check = 1; + cancel_delayed_work(&priv->reset_work); + cancel_delayed_work(&priv->security_work); + cancel_delayed_work(&priv->wx_event_work); + cancel_delayed_work(&priv->hang_check); + cancel_delayed_work(&priv->rf_kill); + destroy_workqueue(priv->workqueue); + priv->workqueue = NULL; + } +} + +static int ipw2100_tx_allocate(struct ipw2100_priv *priv) +{ + int i, j, err = -EINVAL; + void *v; + dma_addr_t p; + + IPW_DEBUG_INFO("enter\n"); + + err = bd_queue_allocate(priv, &priv->tx_queue, TX_QUEUE_LENGTH); + if (err) { + IPW_DEBUG_ERROR("%s: failed bd_queue_allocate\n", + priv->net_dev->name); + return err; + } + + priv->tx_buffers = (struct ipw2100_tx_packet *)kmalloc( + TX_PENDED_QUEUE_LENGTH * sizeof(struct ipw2100_tx_packet), + GFP_ATOMIC); + if (!priv->tx_buffers) { + IPW_DEBUG_ERROR("%s: alloc failed form tx buffers.\n", + priv->net_dev->name); + bd_queue_free(priv, &priv->tx_queue); + return -ENOMEM; + } + + for (i = 0; i < TX_PENDED_QUEUE_LENGTH; i++) { + v = pci_alloc_consistent( + priv->pci_dev, sizeof(struct ipw2100_data_header), &p); + if (!v) { + IPW_DEBUG_ERROR("%s: PCI alloc failed for tx " + "buffers.\n", priv->net_dev->name); + err = -ENOMEM; + break; + } + + priv->tx_buffers[i].type = DATA; + priv->tx_buffers[i].info.d_struct.data = (struct ipw2100_data_header*)v; + priv->tx_buffers[i].info.d_struct.data_phys = p; + priv->tx_buffers[i].info.d_struct.txb = NULL; + } + + if (i == TX_PENDED_QUEUE_LENGTH) + return 0; + + for (j = 0; j < i; j++) { + pci_free_consistent( + priv->pci_dev, + sizeof(struct ipw2100_data_header), + priv->tx_buffers[j].info.d_struct.data, + priv->tx_buffers[j].info.d_struct.data_phys); + } + + kfree(priv->tx_buffers); + priv->tx_buffers = NULL; + + return err; +} + +static void ipw2100_tx_initialize(struct ipw2100_priv *priv) +{ + int i; + + IPW_DEBUG_INFO("enter\n"); + + /* + * reinitialize packet info lists + */ + INIT_LIST_HEAD(&priv->fw_pend_list); + INIT_STAT(&priv->fw_pend_stat); + + /* + * reinitialize lists + */ + INIT_LIST_HEAD(&priv->tx_pend_list); + INIT_LIST_HEAD(&priv->tx_free_list); + INIT_STAT(&priv->tx_pend_stat); + INIT_STAT(&priv->tx_free_stat); + + for (i = 0; i < TX_PENDED_QUEUE_LENGTH; i++) { + /* We simply drop any SKBs that have been queued for + * transmit */ + if (priv->tx_buffers[i].info.d_struct.txb) { + ieee80211_txb_free(priv->tx_buffers[i].info.d_struct.txb); + priv->tx_buffers[i].info.d_struct.txb = NULL; + } + + list_add_tail(&priv->tx_buffers[i].list, &priv->tx_free_list); + } + + SET_STAT(&priv->tx_free_stat, i); + + priv->tx_queue.oldest = 0; + priv->tx_queue.available = priv->tx_queue.entries; + priv->tx_queue.next = 0; + INIT_STAT(&priv->txq_stat); + SET_STAT(&priv->txq_stat, priv->tx_queue.available); + + bd_queue_initialize(priv, &priv->tx_queue, + IPW_MEM_HOST_SHARED_TX_QUEUE_BD_BASE, + IPW_MEM_HOST_SHARED_TX_QUEUE_BD_SIZE, + IPW_MEM_HOST_SHARED_TX_QUEUE_READ_INDEX, + IPW_MEM_HOST_SHARED_TX_QUEUE_WRITE_INDEX); + + IPW_DEBUG_INFO("exit\n"); + +} + +static void ipw2100_tx_free(struct ipw2100_priv *priv) +{ + int i; + + IPW_DEBUG_INFO("enter\n"); + + bd_queue_free(priv, &priv->tx_queue); + + if (!priv->tx_buffers) + return; + + for (i = 0; i < TX_PENDED_QUEUE_LENGTH; i++) { + if (priv->tx_buffers[i].info.d_struct.txb) { + ieee80211_txb_free(priv->tx_buffers[i].info.d_struct.txb); + priv->tx_buffers[i].info.d_struct.txb = NULL; + } + if (priv->tx_buffers[i].info.d_struct.data) + pci_free_consistent( + priv->pci_dev, + sizeof(struct ipw2100_data_header), + priv->tx_buffers[i].info.d_struct.data, + priv->tx_buffers[i].info.d_struct.data_phys); + } + + kfree(priv->tx_buffers); + priv->tx_buffers = NULL; + + IPW_DEBUG_INFO("exit\n"); +} + + + +static int ipw2100_rx_allocate(struct ipw2100_priv *priv) +{ + int i, j, err = -EINVAL; + + IPW_DEBUG_INFO("enter\n"); + + err = bd_queue_allocate(priv, &priv->rx_queue, RX_QUEUE_LENGTH); + if (err) { + IPW_DEBUG_INFO("failed bd_queue_allocate\n"); + return err; + } + + err = status_queue_allocate(priv, RX_QUEUE_LENGTH); + if (err) { + IPW_DEBUG_INFO("failed status_queue_allocate\n"); + bd_queue_free(priv, &priv->rx_queue); + return err; + } + + /* + * allocate packets + */ + priv->rx_buffers = (struct ipw2100_rx_packet *) + kmalloc(RX_QUEUE_LENGTH * sizeof(struct ipw2100_rx_packet), + GFP_KERNEL); + if (!priv->rx_buffers) { + IPW_DEBUG_INFO("can't allocate rx packet buffer table\n"); + + bd_queue_free(priv, &priv->rx_queue); + + status_queue_free(priv); + + return -ENOMEM; + } + + for (i = 0; i < RX_QUEUE_LENGTH; i++) { + struct ipw2100_rx_packet *packet = &priv->rx_buffers[i]; + + err = ipw2100_alloc_skb(priv, packet); + if (unlikely(err)) { + err = -ENOMEM; + break; + } + + /* The BD holds the cache aligned address */ + priv->rx_queue.drv[i].host_addr = packet->dma_addr; + priv->rx_queue.drv[i].buf_length = IPW_RX_NIC_BUFFER_LENGTH; + priv->status_queue.drv[i].status_fields = 0; + } + + if (i == RX_QUEUE_LENGTH) + return 0; + + for (j = 0; j < i; j++) { + pci_unmap_single(priv->pci_dev, priv->rx_buffers[j].dma_addr, + sizeof(struct ipw2100_rx_packet), + PCI_DMA_FROMDEVICE); + dev_kfree_skb(priv->rx_buffers[j].skb); + } + + kfree(priv->rx_buffers); + priv->rx_buffers = NULL; + + bd_queue_free(priv, &priv->rx_queue); + + status_queue_free(priv); + + return err; +} + +static void ipw2100_rx_initialize(struct ipw2100_priv *priv) +{ + IPW_DEBUG_INFO("enter\n"); + + priv->rx_queue.oldest = 0; + priv->rx_queue.available = priv->rx_queue.entries - 1; + priv->rx_queue.next = priv->rx_queue.entries - 1; + + INIT_STAT(&priv->rxq_stat); + SET_STAT(&priv->rxq_stat, priv->rx_queue.available); + + bd_queue_initialize(priv, &priv->rx_queue, + IPW_MEM_HOST_SHARED_RX_BD_BASE, + IPW_MEM_HOST_SHARED_RX_BD_SIZE, + IPW_MEM_HOST_SHARED_RX_READ_INDEX, + IPW_MEM_HOST_SHARED_RX_WRITE_INDEX); + + /* set up the status queue */ + write_register(priv->net_dev, IPW_MEM_HOST_SHARED_RX_STATUS_BASE, + priv->status_queue.nic); + + IPW_DEBUG_INFO("exit\n"); +} + +static void ipw2100_rx_free(struct ipw2100_priv *priv) +{ + int i; + + IPW_DEBUG_INFO("enter\n"); + + bd_queue_free(priv, &priv->rx_queue); + status_queue_free(priv); + + if (!priv->rx_buffers) + return; + + for (i = 0; i < RX_QUEUE_LENGTH; i++) { + if (priv->rx_buffers[i].rxp) { + pci_unmap_single(priv->pci_dev, + priv->rx_buffers[i].dma_addr, + sizeof(struct ipw2100_rx), + PCI_DMA_FROMDEVICE); + dev_kfree_skb(priv->rx_buffers[i].skb); + } + } + + kfree(priv->rx_buffers); + priv->rx_buffers = NULL; + + IPW_DEBUG_INFO("exit\n"); +} + +static int ipw2100_read_mac_address(struct ipw2100_priv *priv) +{ + u32 length = ETH_ALEN; + u8 mac[ETH_ALEN]; + + int err; + + err = ipw2100_get_ordinal(priv, IPW_ORD_STAT_ADAPTER_MAC, + mac, &length); + if (err) { + IPW_DEBUG_INFO("MAC address read failed\n"); + return -EIO; + } + IPW_DEBUG_INFO("card MAC is %02X:%02X:%02X:%02X:%02X:%02X\n", + mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); + + memcpy(priv->net_dev->dev_addr, mac, ETH_ALEN); + + return 0; +} + +/******************************************************************** + * + * Firmware Commands + * + ********************************************************************/ + +int ipw2100_set_mac_address(struct ipw2100_priv *priv, int batch_mode) +{ + struct host_command cmd = { + .host_command = ADAPTER_ADDRESS, + .host_command_sequence = 0, + .host_command_length = ETH_ALEN + }; + int err; + + IPW_DEBUG_HC("SET_MAC_ADDRESS\n"); + + IPW_DEBUG_INFO("enter\n"); + + if (priv->config & CFG_CUSTOM_MAC) { + memcpy(cmd.host_command_parameters, priv->mac_addr, + ETH_ALEN); + memcpy(priv->net_dev->dev_addr, priv->mac_addr, ETH_ALEN); + } else + memcpy(cmd.host_command_parameters, priv->net_dev->dev_addr, + ETH_ALEN); + + err = ipw2100_hw_send_command(priv, &cmd); + + IPW_DEBUG_INFO("exit\n"); + return err; +} + +int ipw2100_set_port_type(struct ipw2100_priv *priv, u32 port_type, + int batch_mode) +{ + struct host_command cmd = { + .host_command = PORT_TYPE, + .host_command_sequence = 0, + .host_command_length = sizeof(u32) + }; + int err; + + switch (port_type) { + case IW_MODE_INFRA: + cmd.host_command_parameters[0] = IPW_BSS; + break; + case IW_MODE_ADHOC: + cmd.host_command_parameters[0] = IPW_IBSS; + break; + } + + IPW_DEBUG_HC("PORT_TYPE: %s\n", + port_type == IPW_IBSS ? "Ad-Hoc" : "Managed"); + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) { + IPW_DEBUG_ERROR("%s: Could not disable adapter %d\n", + priv->net_dev->name, err); + return err; + } + } + + /* send cmd to firmware */ + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) + ipw2100_enable_adapter(priv); + + return err; +} + + +int ipw2100_set_channel(struct ipw2100_priv *priv, u32 channel, int batch_mode) +{ + struct host_command cmd = { + .host_command = CHANNEL, + .host_command_sequence = 0, + .host_command_length = sizeof(u32) + }; + int err; + + cmd.host_command_parameters[0] = channel; + + IPW_DEBUG_HC("CHANNEL: %d\n", channel); + + /* If BSS then we don't support channel selection */ + if (priv->ieee->iw_mode == IW_MODE_INFRA) + return 0; + + if ((channel != 0) && + ((channel < REG_MIN_CHANNEL) || (channel > REG_MAX_CHANNEL))) + return -EINVAL; + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) { + IPW_DEBUG_INFO("Failed to set channel to %d", + channel); + return err; + } + + if (channel) + priv->config |= CFG_STATIC_CHANNEL; + else + priv->config &= ~CFG_STATIC_CHANNEL; + + priv->channel = channel; + + if (!batch_mode) { + err = ipw2100_enable_adapter(priv); + if (err) + return err; + } + + return 0; +} + +int ipw2100_system_config(struct ipw2100_priv *priv, int batch_mode) +{ + struct host_command cmd = { + .host_command = SYSTEM_CONFIG, + .host_command_sequence = 0, + .host_command_length = 12, + }; + u32 ibss_mask, len = sizeof(u32); + int err; + + /* Set system configuration */ + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) + cmd.host_command_parameters[0] |= IPW_CFG_IBSS_AUTO_START; + + cmd.host_command_parameters[0] |= IPW_CFG_IBSS_MASK | + IPW_CFG_BSS_MASK | + IPW_CFG_802_1x_ENABLE; + + if (!(priv->config & CFG_LONG_PREAMBLE)) + cmd.host_command_parameters[0] |= IPW_CFG_PREAMBLE_AUTO; + + err = ipw2100_get_ordinal(priv, + IPW_ORD_EEPROM_IBSS_11B_CHANNELS, + &ibss_mask, &len); + if (err) + ibss_mask = IPW_IBSS_11B_DEFAULT_MASK; + + cmd.host_command_parameters[1] = REG_CHANNEL_MASK; + cmd.host_command_parameters[2] = REG_CHANNEL_MASK & ibss_mask; + + /* 11b only */ + /*cmd.host_command_parameters[0] |= DIVERSITY_ANTENNA_A;*/ + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + +/* If IPv6 is configured in the kernel then we don't want to filter out all + * of the multicast packets as IPv6 needs some. */ +#if !defined(CONFIG_IPV6) && !defined(CONFIG_IPV6_MODULE) + cmd.host_command = ADD_MULTICAST; + cmd.host_command_sequence = 0; + cmd.host_command_length = 0; + + ipw2100_hw_send_command(priv, &cmd); +#endif + if (!batch_mode) { + err = ipw2100_enable_adapter(priv); + if (err) + return err; + } + + return 0; +} + +int ipw2100_set_tx_rates(struct ipw2100_priv *priv, u32 rate, int batch_mode) +{ + struct host_command cmd = { + .host_command = BASIC_TX_RATES, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + cmd.host_command_parameters[0] = rate & TX_RATE_MASK; + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + /* Set BASIC TX Rate first */ + ipw2100_hw_send_command(priv, &cmd); + + /* Set TX Rate */ + cmd.host_command = TX_RATES; + ipw2100_hw_send_command(priv, &cmd); + + /* Set MSDU TX Rate */ + cmd.host_command = MSDU_TX_RATES; + ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) { + err = ipw2100_enable_adapter(priv); + if (err) + return err; + } + + priv->tx_rates = rate; + + return 0; +} + +int ipw2100_set_power_mode(struct ipw2100_priv *priv, + int power_level) +{ + struct host_command cmd = { + .host_command = POWER_MODE, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + cmd.host_command_parameters[0] = power_level; + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + + if (power_level == IPW_POWER_MODE_CAM) + priv->power_mode = IPW_POWER_LEVEL(priv->power_mode); + else + priv->power_mode = IPW_POWER_ENABLED | power_level; + +#ifdef CONFIG_IPW2100_TX_POWER + if (priv->port_type == IBSS && + priv->adhoc_power != DFTL_IBSS_TX_POWER) { + /* Set beacon interval */ + cmd.host_command = TX_POWER_INDEX; + cmd.host_command_parameters[0] = (u32)priv->adhoc_power; + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + } +#endif + + return 0; +} + + +int ipw2100_set_rts_threshold(struct ipw2100_priv *priv, u32 threshold) +{ + struct host_command cmd = { + .host_command = RTS_THRESHOLD, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + if (threshold & RTS_DISABLED) + cmd.host_command_parameters[0] = MAX_RTS_THRESHOLD; + else + cmd.host_command_parameters[0] = threshold & ~RTS_DISABLED; + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + + priv->rts_threshold = threshold; + + return 0; +} + +#if 0 +int ipw2100_set_fragmentation_threshold(struct ipw2100_priv *priv, + u32 threshold, int batch_mode) +{ + struct host_command cmd = { + .host_command = FRAG_THRESHOLD, + .host_command_sequence = 0, + .host_command_length = 4, + .host_command_parameters[0] = 0, + }; + int err; + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + if (threshold == 0) + threshold = DEFAULT_FRAG_THRESHOLD; + else { + threshold = max(threshold, MIN_FRAG_THRESHOLD); + threshold = min(threshold, MAX_FRAG_THRESHOLD); + } + + cmd.host_command_parameters[0] = threshold; + + IPW_DEBUG_HC("FRAG_THRESHOLD: %u\n", threshold); + + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) + ipw2100_enable_adapter(priv); + + if (!err) + priv->frag_threshold = threshold; + + return err; +} +#endif + +int ipw2100_set_short_retry(struct ipw2100_priv *priv, u32 retry) +{ + struct host_command cmd = { + .host_command = SHORT_RETRY_LIMIT, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + cmd.host_command_parameters[0] = retry; + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + + priv->short_retry_limit = retry; + + return 0; +} + +int ipw2100_set_long_retry(struct ipw2100_priv *priv, u32 retry) +{ + struct host_command cmd = { + .host_command = LONG_RETRY_LIMIT, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + cmd.host_command_parameters[0] = retry; + + err = ipw2100_hw_send_command(priv, &cmd); + if (err) + return err; + + priv->long_retry_limit = retry; + + return 0; +} + + +int ipw2100_set_mandatory_bssid(struct ipw2100_priv *priv, u8 *bssid, + int batch_mode) +{ + struct host_command cmd = { + .host_command = MANDATORY_BSSID, + .host_command_sequence = 0, + .host_command_length = (bssid == NULL) ? 0 : ETH_ALEN + }; + int err; + +#ifdef CONFIG_IPW_DEBUG + if (bssid != NULL) + IPW_DEBUG_HC( + "MANDATORY_BSSID: %02X:%02X:%02X:%02X:%02X:%02X\n", + bssid[0], bssid[1], bssid[2], bssid[3], bssid[4], + bssid[5]); + else + IPW_DEBUG_HC("MANDATORY_BSSID: <clear>\n"); +#endif + /* if BSSID is empty then we disable mandatory bssid mode */ + if (bssid != NULL) + memcpy((u8 *)cmd.host_command_parameters, bssid, ETH_ALEN); + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) + ipw2100_enable_adapter(priv); + + return err; +} + +#ifdef CONFIG_IEEE80211_WPA +static int ipw2100_disassociate_bssid(struct ipw2100_priv *priv) +{ + struct host_command cmd = { + .host_command = DISASSOCIATION_BSSID, + .host_command_sequence = 0, + .host_command_length = ETH_ALEN + }; + int err; + int len; + + IPW_DEBUG_HC("DISASSOCIATION_BSSID\n"); + + len = ETH_ALEN; + /* The Firmware currently ignores the BSSID and just disassociates from + * the currently associated AP -- but in the off chance that a future + * firmware does use the BSSID provided here, we go ahead and try and + * set it to the currently associated AP's BSSID */ + memcpy(cmd.host_command_parameters, priv->bssid, ETH_ALEN); + + err = ipw2100_hw_send_command(priv, &cmd); + + return err; +} +#endif + +/* + * Pseudo code for setting up wpa_frame: + */ +#if 0 +void x(struct ieee80211_assoc_frame *wpa_assoc) +{ + struct ipw2100_wpa_assoc_frame frame; + frame->fixed_ie_mask = IPW_WPA_CAPABILTIES | + IPW_WPA_LISTENINTERVAL | + IPW_WPA_AP_ADDRESS; + frame->capab_info = wpa_assoc->capab_info; + frame->lisen_interval = wpa_assoc->listent_interval; + memcpy(frame->current_ap, wpa_assoc->current_ap, ETH_ALEN); + + /* UNKNOWN -- I'm not postivive about this part; don't have any WPA + * setup here to test it with. + * + * Walk the IEs in the wpa_assoc and figure out the total size of all + * that data. Stick that into frame->var_ie_len. Then memcpy() all of + * the IEs from wpa_frame into frame. + */ + frame->var_ie_len = calculate_ie_len(wpa_assoc); + memcpy(frame->var_ie, wpa_assoc->variable, frame->var_ie_len); + + ipw2100_set_wpa_ie(priv, &frame, 0); +} +#endif + + + + +static int ipw2100_set_wpa_ie(struct ipw2100_priv *, + struct ipw2100_wpa_assoc_frame *, int) +__attribute__ ((unused)); + +static int ipw2100_set_wpa_ie(struct ipw2100_priv *priv, + struct ipw2100_wpa_assoc_frame *wpa_frame, + int batch_mode) +{ + struct host_command cmd = { + .host_command = SET_WPA_IE, + .host_command_sequence = 0, + .host_command_length = sizeof(struct ipw2100_wpa_assoc_frame), + }; + int err; + + IPW_DEBUG_HC("SET_WPA_IE\n"); + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + memcpy(cmd.host_command_parameters, wpa_frame, + sizeof(struct ipw2100_wpa_assoc_frame)); + + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) { + if (ipw2100_enable_adapter(priv)) + err = -EIO; + } + + return err; +} + +struct security_info_params { + u32 allowed_ciphers; + u16 version; + u8 auth_mode; + u8 replay_counters_number; + u8 unicast_using_group; +} __attribute__ ((packed)); + +int ipw2100_set_security_information(struct ipw2100_priv *priv, + int auth_mode, + int security_level, + int unicast_using_group, + int batch_mode) +{ + struct host_command cmd = { + .host_command = SET_SECURITY_INFORMATION, + .host_command_sequence = 0, + .host_command_length = sizeof(struct security_info_params) + }; + struct security_info_params *security = + (struct security_info_params *)&cmd.host_command_parameters; + int err; + memset(security, 0, sizeof(*security)); + + /* If shared key AP authentication is turned on, then we need to + * configure the firmware to try and use it. + * + * Actual data encryption/decryption is handled by the host. */ + security->auth_mode = auth_mode; + security->unicast_using_group = unicast_using_group; + + switch (security_level) { + default: + case SEC_LEVEL_0: + security->allowed_ciphers = IPW_NONE_CIPHER; + break; + case SEC_LEVEL_1: + security->allowed_ciphers = IPW_WEP40_CIPHER | + IPW_WEP104_CIPHER; + break; + case SEC_LEVEL_2: + security->allowed_ciphers = IPW_WEP40_CIPHER | + IPW_WEP104_CIPHER | IPW_TKIP_CIPHER; + break; + case SEC_LEVEL_2_CKIP: + security->allowed_ciphers = IPW_WEP40_CIPHER | + IPW_WEP104_CIPHER | IPW_CKIP_CIPHER; + break; + case SEC_LEVEL_3: + security->allowed_ciphers = IPW_WEP40_CIPHER | + IPW_WEP104_CIPHER | IPW_TKIP_CIPHER | IPW_CCMP_CIPHER; + break; + } + + IPW_DEBUG_HC( + "SET_SECURITY_INFORMATION: auth:%d cipher:0x%02X (level %d)\n", + security->auth_mode, security->allowed_ciphers, security_level); + + security->replay_counters_number = 0; + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) + ipw2100_enable_adapter(priv); + + return err; +} + +int ipw2100_set_tx_power(struct ipw2100_priv *priv, + u32 tx_power) +{ + struct host_command cmd = { + .host_command = TX_POWER_INDEX, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err = 0; + + cmd.host_command_parameters[0] = tx_power; + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) + err = ipw2100_hw_send_command(priv, &cmd); + if (!err) + priv->tx_power = tx_power; + + return 0; +} + +int ipw2100_set_ibss_beacon_interval(struct ipw2100_priv *priv, + u32 interval, int batch_mode) +{ + struct host_command cmd = { + .host_command = BEACON_INTERVAL, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + cmd.host_command_parameters[0] = interval; + + IPW_DEBUG_INFO("enter\n"); + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) { + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) { + err = ipw2100_enable_adapter(priv); + if (err) + return err; + } + } + + IPW_DEBUG_INFO("exit\n"); + + return 0; +} + + +void ipw2100_queues_initialize(struct ipw2100_priv *priv) +{ + ipw2100_tx_initialize(priv); + ipw2100_rx_initialize(priv); + ipw2100_msg_initialize(priv); +} + +void ipw2100_queues_free(struct ipw2100_priv *priv) +{ + ipw2100_tx_free(priv); + ipw2100_rx_free(priv); + ipw2100_msg_free(priv); +} + +int ipw2100_queues_allocate(struct ipw2100_priv *priv) +{ + if (ipw2100_tx_allocate(priv) || + ipw2100_rx_allocate(priv) || + ipw2100_msg_allocate(priv)) + goto fail; + + return 0; + + fail: + ipw2100_tx_free(priv); + ipw2100_rx_free(priv); + ipw2100_msg_free(priv); + return -ENOMEM; +} + +#define IPW_PRIVACY_CAPABLE 0x0008 + +static int ipw2100_set_wep_flags(struct ipw2100_priv *priv, u32 flags, + int batch_mode) +{ + struct host_command cmd = { + .host_command = WEP_FLAGS, + .host_command_sequence = 0, + .host_command_length = 4 + }; + int err; + + cmd.host_command_parameters[0] = flags; + + IPW_DEBUG_HC("WEP_FLAGS: flags = 0x%08X\n", flags); + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) { + IPW_DEBUG_ERROR("%s: Could not disable adapter %d\n", + priv->net_dev->name, err); + return err; + } + } + + /* send cmd to firmware */ + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) + ipw2100_enable_adapter(priv); + + return err; +} + +struct ipw2100_wep_key { + u8 idx; + u8 len; + u8 key[13]; +}; + +/* Macros to ease up priting WEP keys */ +#define WEP_FMT_64 "%02X%02X%02X%02X-%02X" +#define WEP_FMT_128 "%02X%02X%02X%02X-%02X%02X%02X%02X-%02X%02X%02X" +#define WEP_STR_64(x) x[0],x[1],x[2],x[3],x[4] +#define WEP_STR_128(x) x[0],x[1],x[2],x[3],x[4],x[5],x[6],x[7],x[8],x[9],x[10] + + +/** + * Set a the wep key + * + * @priv: struct to work on + * @idx: index of the key we want to set + * @key: ptr to the key data to set + * @len: length of the buffer at @key + * @batch_mode: FIXME perform the operation in batch mode, not + * disabling the device. + * + * @returns 0 if OK, < 0 errno code on error. + * + * Fill out a command structure with the new wep key, length an + * index and send it down the wire. + */ +static int ipw2100_set_key(struct ipw2100_priv *priv, + int idx, char *key, int len, int batch_mode) +{ + int keylen = len ? (len <= 5 ? 5 : 13) : 0; + struct host_command cmd = { + .host_command = WEP_KEY_INFO, + .host_command_sequence = 0, + .host_command_length = sizeof(struct ipw2100_wep_key), + }; + struct ipw2100_wep_key *wep_key = (void*)cmd.host_command_parameters; + int err; + + IPW_DEBUG_HC("WEP_KEY_INFO: index = %d, len = %d/%d\n", + idx, keylen, len); + + /* NOTE: We don't check cached values in case the firmware was reset + * or some other problem is occuring. If the user is setting the key, + * then we push the change */ + + wep_key->idx = idx; + wep_key->len = keylen; + + if (keylen) { + memcpy(wep_key->key, key, len); + memset(wep_key->key + len, 0, keylen - len); + } + + /* Will be optimized out on debug not being configured in */ + if (keylen == 0) + IPW_DEBUG_WEP("%s: Clearing key %d\n", + priv->net_dev->name, wep_key->idx); + else if (keylen == 5) + IPW_DEBUG_WEP("%s: idx: %d, len: %d key: " WEP_FMT_64 "\n", + priv->net_dev->name, wep_key->idx, wep_key->len, + WEP_STR_64(wep_key->key)); + else + IPW_DEBUG_WEP("%s: idx: %d, len: %d key: " WEP_FMT_128 + "\n", + priv->net_dev->name, wep_key->idx, wep_key->len, + WEP_STR_128(wep_key->key)); + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + /* FIXME: IPG: shouldn't this prink be in _disable_adapter()? */ + if (err) { + IPW_DEBUG_ERROR("%s: Could not disable adapter %d\n", + priv->net_dev->name, err); + return err; + } + } + + /* send cmd to firmware */ + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) { + int err2 = ipw2100_enable_adapter(priv); + if (err == 0) + err = err2; + } + return err; +} + +static int ipw2100_set_key_index(struct ipw2100_priv *priv, + int idx, int batch_mode) +{ + struct host_command cmd = { + .host_command = WEP_KEY_INDEX, + .host_command_sequence = 0, + .host_command_length = 4, + .host_command_parameters[0] = idx, + }; + int err; + + IPW_DEBUG_HC("WEP_KEY_INDEX: index = %d\n", idx); + + if (idx < 0 || idx > 3) + return -EINVAL; + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) { + IPW_DEBUG_ERROR("%s: Could not disable adapter %d\n", + priv->net_dev->name, err); + return err; + } + } + + /* send cmd to firmware */ + err = ipw2100_hw_send_command(priv, &cmd); + + if (!batch_mode) + ipw2100_enable_adapter(priv); + + return err; +} + + +static int ipw2100_configure_security(struct ipw2100_priv *priv, + int batch_mode) +{ + int i, err, auth_mode, sec_level, use_group; + + if (!(priv->status & STATUS_RUNNING)) + return 0; + + if (!batch_mode) { + err = ipw2100_disable_adapter(priv); + if (err) + return err; + } + + if (!priv->sec.enabled) { + err = ipw2100_set_security_information( + priv, IPW_AUTH_OPEN, SEC_LEVEL_0, 0, 1); + } else { + auth_mode = IPW_AUTH_OPEN; + if ((priv->sec.flags & SEC_AUTH_MODE) && + (priv->sec.auth_mode == WLAN_AUTH_SHARED_KEY)) + auth_mode = IPW_AUTH_SHARED; + + sec_level = SEC_LEVEL_0; + if (priv->sec.flags & SEC_LEVEL) + sec_level = priv->sec.level; + + use_group = 0; + if (priv->sec.flags & SEC_UNICAST_GROUP) + use_group = priv->sec.unicast_uses_group; + + err = ipw2100_set_security_information( + priv, auth_mode, sec_level, use_group, 1); + } + + if (err) + goto exit; + + if (priv->sec.enabled) { + for (i = 0; i < 4; i++) { + if (!(priv->sec.flags & (1 << i))) { + memset(priv->sec.keys[i], 0, WEP_KEY_LEN); + priv->sec.key_sizes[i] = 0; + } else { + err = ipw2100_set_key(priv, i, + priv->sec.keys[i], + priv->sec.key_sizes[i], + 1); + if (err) + goto exit; + } + } + + ipw2100_set_key_index(priv, priv->ieee->tx_keyidx, 1); + } + + /* Always enable privacy so the Host can filter WEP packets if + * encrypted data is sent up */ + err = ipw2100_set_wep_flags( + priv, priv->sec.enabled ? IPW_PRIVACY_CAPABLE : 0, 1); + if (err) + goto exit; + + priv->status &= ~STATUS_SECURITY_UPDATED; + + exit: + if (!batch_mode) + ipw2100_enable_adapter(priv); + + return err; +} + +static void ipw2100_security_work(struct ipw2100_priv *priv) +{ + /* If we happen to have reconnected before we get a chance to + * process this, then update the security settings--which causes + * a disassociation to occur */ + if (!(priv->status & STATUS_ASSOCIATED) && + priv->status & STATUS_SECURITY_UPDATED) + ipw2100_configure_security(priv, 0); +} + +static void shim__set_security(struct net_device *dev, + struct ieee80211_security *sec) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int i, force_update = 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) + goto done; + + for (i = 0; i < 4; i++) { + if (sec->flags & (1 << i)) { + priv->sec.key_sizes[i] = sec->key_sizes[i]; + if (sec->key_sizes[i] == 0) + priv->sec.flags &= ~(1 << i); + else + memcpy(priv->sec.keys[i], sec->keys[i], + sec->key_sizes[i]); + priv->sec.flags |= (1 << i); + priv->status |= STATUS_SECURITY_UPDATED; + } + } + + if ((sec->flags & SEC_ACTIVE_KEY) && + priv->sec.active_key != sec->active_key) { + if (sec->active_key <= 3) { + priv->sec.active_key = sec->active_key; + priv->sec.flags |= SEC_ACTIVE_KEY; + } else + priv->sec.flags &= ~SEC_ACTIVE_KEY; + + priv->status |= STATUS_SECURITY_UPDATED; + } + + if ((sec->flags & SEC_AUTH_MODE) && + (priv->sec.auth_mode != sec->auth_mode)) { + priv->sec.auth_mode = sec->auth_mode; + priv->sec.flags |= SEC_AUTH_MODE; + priv->status |= STATUS_SECURITY_UPDATED; + } + + if (sec->flags & SEC_ENABLED && + priv->sec.enabled != sec->enabled) { + priv->sec.flags |= SEC_ENABLED; + priv->sec.enabled = sec->enabled; + priv->status |= STATUS_SECURITY_UPDATED; + force_update = 1; + } + + if (sec->flags & SEC_LEVEL && + priv->sec.level != sec->level) { + priv->sec.level = sec->level; + priv->sec.flags |= SEC_LEVEL; + priv->status |= STATUS_SECURITY_UPDATED; + } + + IPW_DEBUG_WEP("Security flags: %c %c%c%c%c %c%c%c%c\n", + priv->sec.flags & (1<<8) ? '1' : '0', + priv->sec.flags & (1<<7) ? '1' : '0', + priv->sec.flags & (1<<6) ? '1' : '0', + priv->sec.flags & (1<<5) ? '1' : '0', + priv->sec.flags & (1<<4) ? '1' : '0', + priv->sec.flags & (1<<3) ? '1' : '0', + priv->sec.flags & (1<<2) ? '1' : '0', + priv->sec.flags & (1<<1) ? '1' : '0', + priv->sec.flags & (1<<0) ? '1' : '0'); + +/* As a temporary work around to enable WPA until we figure out why + * wpa_supplicant toggles the security capability of the driver, which + * forces a disassocation with force_update... + * + * if (force_update || !(priv->status & STATUS_ASSOCIATED))*/ + if (!(priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING))) + ipw2100_configure_security(priv, 0); +done: + up(&priv->action_sem); +} + +static int ipw2100_adapter_setup(struct ipw2100_priv *priv) +{ + int err; + int batch_mode = 1; + u8 *bssid; + + IPW_DEBUG_INFO("enter\n"); + + err = ipw2100_disable_adapter(priv); + if (err) + return err; +#ifdef CONFIG_IPW2100_MONITOR + if (priv->ieee->iw_mode == IW_MODE_MONITOR) { + err = ipw2100_set_channel(priv, priv->channel, batch_mode); + if (err) + return err; + + IPW_DEBUG_INFO("exit\n"); + + return 0; + } +#endif /* CONFIG_IPW2100_MONITOR */ + + err = ipw2100_read_mac_address(priv); + if (err) + return -EIO; + + err = ipw2100_set_mac_address(priv, batch_mode); + if (err) + return err; + + err = ipw2100_set_port_type(priv, priv->ieee->iw_mode, batch_mode); + if (err) + return err; + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) { + err = ipw2100_set_channel(priv, priv->channel, batch_mode); + if (err) + return err; + } + + err = ipw2100_system_config(priv, batch_mode); + if (err) + return err; + + err = ipw2100_set_tx_rates(priv, priv->tx_rates, batch_mode); + if (err) + return err; + + /* Default to power mode OFF */ + err = ipw2100_set_power_mode(priv, IPW_POWER_MODE_CAM); + if (err) + return err; + + err = ipw2100_set_rts_threshold(priv, priv->rts_threshold); + if (err) + return err; + + if (priv->config & CFG_STATIC_BSSID) + bssid = priv->bssid; + else + bssid = NULL; + err = ipw2100_set_mandatory_bssid(priv, bssid, batch_mode); + if (err) + return err; + + if (priv->config & CFG_STATIC_ESSID) + err = ipw2100_set_essid(priv, priv->essid, priv->essid_len, + batch_mode); + else + err = ipw2100_set_essid(priv, NULL, 0, batch_mode); + if (err) + return err; + + err = ipw2100_configure_security(priv, batch_mode); + if (err) + return err; + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) { + err = ipw2100_set_ibss_beacon_interval( + priv, priv->beacon_interval, batch_mode); + if (err) + return err; + + err = ipw2100_set_tx_power(priv, priv->tx_power); + if (err) + return err; + } + + /* + err = ipw2100_set_fragmentation_threshold( + priv, priv->frag_threshold, batch_mode); + if (err) + return err; + */ + + IPW_DEBUG_INFO("exit\n"); + + return 0; +} + + +/************************************************************************* + * + * EXTERNALLY CALLED METHODS + * + *************************************************************************/ + +/* This method is called by the network layer -- not to be confused with + * ipw2100_set_mac_address() declared above called by this driver (and this + * method as well) to talk to the firmware */ +static int ipw2100_set_address(struct net_device *dev, void *p) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct sockaddr *addr = p; + int err = 0; + + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + + down(&priv->action_sem); + + priv->config |= CFG_CUSTOM_MAC; + memcpy(priv->mac_addr, addr->sa_data, ETH_ALEN); + + err = ipw2100_set_mac_address(priv, 0); + if (err) + goto done; + + priv->reset_backoff = 0; + up(&priv->action_sem); + ipw2100_reset_adapter(priv); + return 0; + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_open(struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + unsigned long flags; + IPW_DEBUG_INFO("dev->open\n"); + + spin_lock_irqsave(&priv->low_lock, flags); + if (priv->status & STATUS_ASSOCIATED) + netif_start_queue(dev); + spin_unlock_irqrestore(&priv->low_lock, flags); + + return 0; +} + +static int ipw2100_close(struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + unsigned long flags; + struct list_head *element; + struct ipw2100_tx_packet *packet; + + IPW_DEBUG_INFO("enter\n"); + + spin_lock_irqsave(&priv->low_lock, flags); + + if (priv->status & STATUS_ASSOCIATED) + netif_carrier_off(dev); + netif_stop_queue(dev); + + /* Flush the TX queue ... */ + while (!list_empty(&priv->tx_pend_list)) { + element = priv->tx_pend_list.next; + packet = list_entry(element, struct ipw2100_tx_packet, list); + + list_del(element); + DEC_STAT(&priv->tx_pend_stat); + + ieee80211_txb_free(packet->info.d_struct.txb); + packet->info.d_struct.txb = NULL; + + list_add_tail(element, &priv->tx_free_list); + INC_STAT(&priv->tx_free_stat); + } + spin_unlock_irqrestore(&priv->low_lock, flags); + + IPW_DEBUG_INFO("exit\n"); + + return 0; +} + + + +/* + * TODO: Fix this function... its just wrong + */ +static void ipw2100_tx_timeout(struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + + priv->ieee->stats.tx_errors++; + +#ifdef CONFIG_IPW2100_MONITOR + if (priv->ieee->iw_mode == IW_MODE_MONITOR) + return; +#endif + + IPW_DEBUG_INFO("%s: TX timed out. Scheduling firmware restart.\n", + dev->name); + schedule_reset(priv); +} + + +/* + * TODO: reimplement it so that it reads statistics + * from the adapter using ordinal tables + * instead of/in addition to collecting them + * in the driver + */ +static struct net_device_stats *ipw2100_stats(struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + + return &priv->ieee->stats; +} + +/* Support for wpa_supplicant. Will be replaced with WEXT once + * they get WPA support. */ +#ifdef CONFIG_IEEE80211_WPA + +/* following definitions must match definitions in driver_ipw2100.c */ + +#define IPW2100_IOCTL_WPA_SUPPLICANT SIOCIWFIRSTPRIV+30 + +#define IPW2100_CMD_SET_WPA_PARAM 1 +#define IPW2100_CMD_SET_WPA_IE 2 +#define IPW2100_CMD_SET_ENCRYPTION 3 +#define IPW2100_CMD_MLME 4 + +#define IPW2100_PARAM_WPA_ENABLED 1 +#define IPW2100_PARAM_TKIP_COUNTERMEASURES 2 +#define IPW2100_PARAM_DROP_UNENCRYPTED 3 +#define IPW2100_PARAM_PRIVACY_INVOKED 4 +#define IPW2100_PARAM_AUTH_ALGS 5 +#define IPW2100_PARAM_IEEE_802_1X 6 + +#define IPW2100_MLME_STA_DEAUTH 1 +#define IPW2100_MLME_STA_DISASSOC 2 + +#define IPW2100_CRYPT_ERR_UNKNOWN_ALG 2 +#define IPW2100_CRYPT_ERR_UNKNOWN_ADDR 3 +#define IPW2100_CRYPT_ERR_CRYPT_INIT_FAILED 4 +#define IPW2100_CRYPT_ERR_KEY_SET_FAILED 5 +#define IPW2100_CRYPT_ERR_TX_KEY_SET_FAILED 6 +#define IPW2100_CRYPT_ERR_CARD_CONF_FAILED 7 + +#define IPW2100_CRYPT_ALG_NAME_LEN 16 + +struct ipw2100_param { + u32 cmd; + u8 sta_addr[ETH_ALEN]; + union { + struct { + u8 name; + u32 value; + } wpa_param; + struct { + u32 len; + u8 *data; + } wpa_ie; + struct{ + int command; + int reason_code; + } mlme; + struct { + u8 alg[IPW2100_CRYPT_ALG_NAME_LEN]; + u8 set_tx; + u32 err; + u8 idx; + u8 seq[8]; /* sequence counter (set: RX, get: TX) */ + u16 key_len; + u8 key[0]; + } crypt; + + } u; +}; + +/* end of driver_ipw2100.c code */ + +static int ipw2100_wpa_enable(struct ipw2100_priv *priv, int value){ + + struct ieee80211_device *ieee = priv->ieee; + struct ieee80211_security sec = { + .flags = SEC_LEVEL | SEC_ENABLED, + }; + int ret = 0; + + ieee->wpa_enabled = value; + + if (value){ + sec.level = SEC_LEVEL_3; + sec.enabled = 1; + } else { + sec.level = SEC_LEVEL_0; + sec.enabled = 0; + } + + if (ieee->set_security) + ieee->set_security(ieee->dev, &sec); + else + ret = -EOPNOTSUPP; + + return ret; +} + +#define AUTH_ALG_OPEN_SYSTEM 0x1 +#define AUTH_ALG_SHARED_KEY 0x2 + +static int ipw2100_wpa_set_auth_algs(struct ipw2100_priv *priv, int value){ + + struct ieee80211_device *ieee = priv->ieee; + struct ieee80211_security sec = { + .flags = SEC_AUTH_MODE, + }; + int ret = 0; + + if (value & AUTH_ALG_SHARED_KEY){ + sec.auth_mode = WLAN_AUTH_SHARED_KEY; + ieee->open_wep = 0; + } else { + sec.auth_mode = WLAN_AUTH_OPEN; + ieee->open_wep = 1; + } + + if (ieee->set_security) + ieee->set_security(ieee->dev, &sec); + else + ret = -EOPNOTSUPP; + + return ret; +} + + +static int ipw2100_wpa_set_param(struct net_device *dev, u8 name, u32 value){ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + int ret=0; + + switch(name){ + case IPW2100_PARAM_WPA_ENABLED: + ret = ipw2100_wpa_enable(priv, value); + break; + + case IPW2100_PARAM_TKIP_COUNTERMEASURES: + priv->ieee->tkip_countermeasures=value; + break; + + case IPW2100_PARAM_DROP_UNENCRYPTED: + priv->ieee->drop_unencrypted=value; + break; + + case IPW2100_PARAM_PRIVACY_INVOKED: + priv->ieee->privacy_invoked=value; + break; + + case IPW2100_PARAM_AUTH_ALGS: + ret = ipw2100_wpa_set_auth_algs(priv, value); + break; + + case IPW2100_PARAM_IEEE_802_1X: + priv->ieee->ieee802_1x=value; + break; + + default: + IPW_DEBUG_ERROR("%s: Unknown WPA param: %d\n", + dev->name, name); + ret = -EOPNOTSUPP; + } + + return ret; +} + +static int ipw2100_wpa_mlme(struct net_device *dev, int command, int reason){ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + int ret=0; + + switch(command){ + case IPW2100_MLME_STA_DEAUTH: + // silently ignore + break; + + case IPW2100_MLME_STA_DISASSOC: + ipw2100_disassociate_bssid(priv); + break; + + default: + IPW_DEBUG_ERROR("%s: Unknown MLME request: %d\n", + dev->name, command); + ret = -EOPNOTSUPP; + } + + return ret; +} + + +void ipw2100_wpa_assoc_frame(struct ipw2100_priv *priv, + char *wpa_ie, int wpa_ie_len){ + + struct ipw2100_wpa_assoc_frame frame; + + frame.fixed_ie_mask = 0; + + /* copy WPA IE */ + memcpy(frame.var_ie, wpa_ie, wpa_ie_len); + frame.var_ie_len = wpa_ie_len; + + /* make sure WPA is enabled */ + ipw2100_wpa_enable(priv, 1); + ipw2100_set_wpa_ie(priv, &frame, 0); +} + + +static int ipw2100_wpa_set_wpa_ie(struct net_device *dev, + struct ipw2100_param *param, int plen){ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct ieee80211_device *ieee = priv->ieee; + u8 *buf; + + if (! ieee->wpa_enabled) + return -EOPNOTSUPP; + + if (param->u.wpa_ie.len > MAX_WPA_IE_LEN || + (param->u.wpa_ie.len && + param->u.wpa_ie.data==NULL)) + return -EINVAL; + + if (param->u.wpa_ie.len){ + buf = kmalloc(param->u.wpa_ie.len, GFP_KERNEL); + if (buf == NULL) + return -ENOMEM; + + memcpy(buf, param->u.wpa_ie.data, param->u.wpa_ie.len); + + kfree(ieee->wpa_ie); + ieee->wpa_ie = buf; + ieee->wpa_ie_len = param->u.wpa_ie.len; + + } else { + kfree(ieee->wpa_ie); + ieee->wpa_ie = NULL; + ieee->wpa_ie_len = 0; + } + + ipw2100_wpa_assoc_frame(priv, ieee->wpa_ie, ieee->wpa_ie_len); + + return 0; +} + +/* implementation borrowed from hostap driver */ + +static int ipw2100_wpa_set_encryption(struct net_device *dev, + struct ipw2100_param *param, int param_len){ + + int ret = 0; + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct ieee80211_device *ieee = priv->ieee; + struct ieee80211_crypto_ops *ops; + struct ieee80211_crypt_data **crypt; + + struct ieee80211_security sec = { + .flags = 0, + }; + + param->u.crypt.err = 0; + param->u.crypt.alg[IPW2100_CRYPT_ALG_NAME_LEN - 1] = '\0'; + + if (param_len != + (int) ((char *) param->u.crypt.key - (char *) param) + + param->u.crypt.key_len){ + IPW_DEBUG_INFO("Len mismatch %d, %d\n", param_len, param->u.crypt.key_len); + return -EINVAL; + } + if (param->sta_addr[0] == 0xff && param->sta_addr[1] == 0xff && + param->sta_addr[2] == 0xff && param->sta_addr[3] == 0xff && + param->sta_addr[4] == 0xff && param->sta_addr[5] == 0xff) { + if (param->u.crypt.idx >= WEP_KEYS) + return -EINVAL; + crypt = &ieee->crypt[param->u.crypt.idx]; + } else { + return -EINVAL; + } + + if (strcmp(param->u.crypt.alg, "none") == 0) { + if (crypt){ + sec.enabled = 0; + sec.level = SEC_LEVEL_0; + sec.flags |= SEC_ENABLED | SEC_LEVEL; + ieee80211_crypt_delayed_deinit(ieee, crypt); + } + goto done; + } + sec.enabled = 1; + sec.flags |= SEC_ENABLED; + + ops = ieee80211_get_crypto_ops(param->u.crypt.alg); + if (ops == NULL && strcmp(param->u.crypt.alg, "WEP") == 0) { + request_module("ieee80211_crypt_wep"); + ops = ieee80211_get_crypto_ops(param->u.crypt.alg); + } else if (ops == NULL && strcmp(param->u.crypt.alg, "TKIP") == 0) { + request_module("ieee80211_crypt_tkip"); + ops = ieee80211_get_crypto_ops(param->u.crypt.alg); + } else if (ops == NULL && strcmp(param->u.crypt.alg, "CCMP") == 0) { + request_module("ieee80211_crypt_ccmp"); + ops = ieee80211_get_crypto_ops(param->u.crypt.alg); + } + if (ops == NULL) { + IPW_DEBUG_INFO("%s: unknown crypto alg '%s'\n", + dev->name, param->u.crypt.alg); + param->u.crypt.err = IPW2100_CRYPT_ERR_UNKNOWN_ALG; + ret = -EINVAL; + goto done; + } + + if (*crypt == NULL || (*crypt)->ops != ops) { + struct ieee80211_crypt_data *new_crypt; + + ieee80211_crypt_delayed_deinit(ieee, crypt); + + new_crypt = (struct ieee80211_crypt_data *) + kmalloc(sizeof(struct ieee80211_crypt_data), GFP_KERNEL); + if (new_crypt == NULL) { + ret = -ENOMEM; + goto done; + } + memset(new_crypt, 0, sizeof(struct ieee80211_crypt_data)); + new_crypt->ops = ops; + if (new_crypt->ops && try_module_get(new_crypt->ops->owner)) + new_crypt->priv = new_crypt->ops->init(param->u.crypt.idx); + + if (new_crypt->priv == NULL) { + kfree(new_crypt); + param->u.crypt.err = + IPW2100_CRYPT_ERR_CRYPT_INIT_FAILED; + ret = -EINVAL; + goto done; + } + + *crypt = new_crypt; + } + + if (param->u.crypt.key_len > 0 && (*crypt)->ops->set_key && + (*crypt)->ops->set_key(param->u.crypt.key, + param->u.crypt.key_len, param->u.crypt.seq, + (*crypt)->priv) < 0) { + IPW_DEBUG_INFO("%s: key setting failed\n", + dev->name); + param->u.crypt.err = IPW2100_CRYPT_ERR_KEY_SET_FAILED; + ret = -EINVAL; + goto done; + } + + if (param->u.crypt.set_tx){ + ieee->tx_keyidx = param->u.crypt.idx; + sec.active_key = param->u.crypt.idx; + sec.flags |= SEC_ACTIVE_KEY; + } + + if (ops->name != NULL){ + + if (strcmp(ops->name, "WEP") == 0) { + memcpy(sec.keys[param->u.crypt.idx], param->u.crypt.key, param->u.crypt.key_len); + sec.key_sizes[param->u.crypt.idx] = param->u.crypt.key_len; + sec.flags |= (1 << param->u.crypt.idx); + sec.flags |= SEC_LEVEL; + sec.level = SEC_LEVEL_1; + } else if (strcmp(ops->name, "TKIP") == 0) { + sec.flags |= SEC_LEVEL; + sec.level = SEC_LEVEL_2; + } else if (strcmp(ops->name, "CCMP") == 0) { + sec.flags |= SEC_LEVEL; + sec.level = SEC_LEVEL_3; + } + } + done: + if (ieee->set_security) + ieee->set_security(ieee->dev, &sec); + + /* Do not reset port if card is in Managed mode since resetting will + * generate new IEEE 802.11 authentication which may end up in looping + * with IEEE 802.1X. If your hardware requires a reset after WEP + * configuration (for example... Prism2), implement the reset_port in + * the callbacks structures used to initialize the 802.11 stack. */ + if (ieee->reset_on_keychange && + ieee->iw_mode != IW_MODE_INFRA && + ieee->reset_port && + ieee->reset_port(dev)) { + IPW_DEBUG_INFO("%s: reset_port failed\n", dev->name); + param->u.crypt.err = IPW2100_CRYPT_ERR_CARD_CONF_FAILED; + return -EINVAL; + } + + return ret; +} + + +static int ipw2100_wpa_supplicant(struct net_device *dev, struct iw_point *p){ + + struct ipw2100_param *param; + int ret=0; + + IPW_DEBUG_IOCTL("wpa_supplicant: len=%d\n", p->length); + + if (p->length < sizeof(struct ipw2100_param) || !p->pointer) + return -EINVAL; + + param = (struct ipw2100_param *)kmalloc(p->length, GFP_KERNEL); + if (param == NULL) + return -ENOMEM; + + if (copy_from_user(param, p->pointer, p->length)){ + kfree(param); + return -EFAULT; + } + + switch (param->cmd){ + + case IPW2100_CMD_SET_WPA_PARAM: + ret = ipw2100_wpa_set_param(dev, param->u.wpa_param.name, + param->u.wpa_param.value); + break; + + case IPW2100_CMD_SET_WPA_IE: + ret = ipw2100_wpa_set_wpa_ie(dev, param, p->length); + break; + + case IPW2100_CMD_SET_ENCRYPTION: + ret = ipw2100_wpa_set_encryption(dev, param, p->length); + break; + + case IPW2100_CMD_MLME: + ret = ipw2100_wpa_mlme(dev, param->u.mlme.command, + param->u.mlme.reason_code); + break; + + default: + IPW_DEBUG_ERROR("%s: Unknown WPA supplicant request: %d\n", + dev->name, param->cmd); + ret = -EOPNOTSUPP; + + } + + if (ret == 0 && copy_to_user(p->pointer, param, p->length)) + ret = -EFAULT; + + kfree(param); + return ret; +} +#endif /* CONFIG_IEEE80211_WPA */ + +static int ipw2100_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) +{ +#ifdef CONFIG_IEEE80211_WPA + struct iwreq *wrq = (struct iwreq *) rq; + int ret=-1; + switch (cmd){ + case IPW2100_IOCTL_WPA_SUPPLICANT: + ret = ipw2100_wpa_supplicant(dev, &wrq->u.data); + return ret; + + default: + return -EOPNOTSUPP; + } + +#endif /* CONFIG_IEEE80211_WPA */ + + return -EOPNOTSUPP; +} + + +static void ipw_ethtool_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + char fw_ver[64], ucode_ver[64]; + + strcpy(info->driver, DRV_NAME); + strcpy(info->version, DRV_VERSION); + + ipw2100_get_fwversion(priv, fw_ver, sizeof(fw_ver)); + ipw2100_get_ucodeversion(priv, ucode_ver, sizeof(ucode_ver)); + + snprintf(info->fw_version, sizeof(info->fw_version), "%s:%d:%s", + fw_ver, priv->eeprom_version, ucode_ver); + + strcpy(info->bus_info, pci_name(priv->pci_dev)); +} + +static u32 ipw2100_ethtool_get_link(struct net_device *dev) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + return (priv->status & STATUS_ASSOCIATED) ? 1 : 0; +} + + +static struct ethtool_ops ipw2100_ethtool_ops = { + .get_link = ipw2100_ethtool_get_link, + .get_drvinfo = ipw_ethtool_get_drvinfo, +}; + +static void ipw2100_hang_check(void *adapter) +{ + struct ipw2100_priv *priv = adapter; + unsigned long flags; + u32 rtc = 0xa5a5a5a5; + u32 len = sizeof(rtc); + int restart = 0; + + spin_lock_irqsave(&priv->low_lock, flags); + + if (priv->fatal_error != 0) { + /* If fatal_error is set then we need to restart */ + IPW_DEBUG_INFO("%s: Hardware fatal error detected.\n", + priv->net_dev->name); + + restart = 1; + } else if (ipw2100_get_ordinal(priv, IPW_ORD_RTC_TIME, &rtc, &len) || + (rtc == priv->last_rtc)) { + /* Check if firmware is hung */ + IPW_DEBUG_INFO("%s: Firmware RTC stalled.\n", + priv->net_dev->name); + + restart = 1; + } + + if (restart) { + /* Kill timer */ + priv->stop_hang_check = 1; + priv->hangs++; + + /* Restart the NIC */ + schedule_reset(priv); + } + + priv->last_rtc = rtc; + + if (!priv->stop_hang_check) + queue_delayed_work(priv->workqueue, &priv->hang_check, HZ / 2); + + spin_unlock_irqrestore(&priv->low_lock, flags); +} + + +static void ipw2100_rf_kill(void *adapter) +{ + struct ipw2100_priv *priv = adapter; + unsigned long flags; + + spin_lock_irqsave(&priv->low_lock, flags); + + if (rf_kill_active(priv)) { + IPW_DEBUG_RF_KILL("RF Kill active, rescheduling GPIO check\n"); + if (!priv->stop_rf_kill) + queue_delayed_work(priv->workqueue, &priv->rf_kill, HZ); + goto exit_unlock; + } + + /* RF Kill is now disabled, so bring the device back up */ + + if (!(priv->status & STATUS_RF_KILL_MASK)) { + IPW_DEBUG_RF_KILL("HW RF Kill no longer active, restarting " + "device\n"); + schedule_reset(priv); + } else + IPW_DEBUG_RF_KILL("HW RF Kill deactivated. SW RF Kill still " + "enabled\n"); + + exit_unlock: + spin_unlock_irqrestore(&priv->low_lock, flags); +} + +static void ipw2100_irq_tasklet(struct ipw2100_priv *priv); + +/* Look into using netdev destructor to shutdown ieee80211? */ + +static struct net_device *ipw2100_alloc_device( + struct pci_dev *pci_dev, + char *base_addr, + unsigned long mem_start, + unsigned long mem_len) +{ + struct ipw2100_priv *priv; + struct net_device *dev; + + dev = alloc_ieee80211(sizeof(struct ipw2100_priv)); + if (!dev) + return NULL; + priv = ieee80211_priv(dev); + priv->ieee = netdev_priv(dev); + priv->pci_dev = pci_dev; + priv->net_dev = dev; + + priv->ieee->hard_start_xmit = ipw2100_tx; + priv->ieee->set_security = shim__set_security; + + dev->open = ipw2100_open; + dev->stop = ipw2100_close; + dev->init = ipw2100_net_init; + dev->do_ioctl = ipw2100_ioctl; + dev->get_stats = ipw2100_stats; + dev->ethtool_ops = &ipw2100_ethtool_ops; + dev->tx_timeout = ipw2100_tx_timeout; + dev->wireless_handlers = &ipw2100_wx_handler_def; + dev->get_wireless_stats = ipw2100_wx_wireless_stats; + dev->set_mac_address = ipw2100_set_address; + dev->watchdog_timeo = 3*HZ; + dev->irq = 0; + + dev->base_addr = (unsigned long)base_addr; + dev->mem_start = mem_start; + dev->mem_end = dev->mem_start + mem_len - 1; + + /* NOTE: We don't use the wireless_handlers hook + * in dev as the system will start throwing WX requests + * to us before we're actually initialized and it just + * ends up causing problems. So, we just handle + * the WX extensions through the ipw2100_ioctl interface */ + + + /* memset() puts everything to 0, so we only have explicitely set + * those values that need to be something else */ + + /* If power management is turned on, default to AUTO mode */ + priv->power_mode = IPW_POWER_AUTO; + + + +#ifdef CONFIG_IEEE80211_WPA + priv->ieee->wpa_enabled = 0; + priv->ieee->tkip_countermeasures = 0; + priv->ieee->drop_unencrypted = 0; + priv->ieee->privacy_invoked = 0; + priv->ieee->ieee802_1x = 1; +#endif /* CONFIG_IEEE80211_WPA */ + + /* Set module parameters */ + switch (mode) { + case 1: + priv->ieee->iw_mode = IW_MODE_ADHOC; + break; +#ifdef CONFIG_IPW2100_MONITOR + case 2: + priv->ieee->iw_mode = IW_MODE_MONITOR; + break; +#endif + default: + case 0: + priv->ieee->iw_mode = IW_MODE_INFRA; + break; + } + + if (disable == 1) + priv->status |= STATUS_RF_KILL_SW; + + if (channel != 0 && + ((channel >= REG_MIN_CHANNEL) && + (channel <= REG_MAX_CHANNEL))) { + priv->config |= CFG_STATIC_CHANNEL; + priv->channel = channel; + } + + if (associate) + priv->config |= CFG_ASSOCIATE; + + priv->beacon_interval = DEFAULT_BEACON_INTERVAL; + priv->short_retry_limit = DEFAULT_SHORT_RETRY_LIMIT; + priv->long_retry_limit = DEFAULT_LONG_RETRY_LIMIT; + priv->rts_threshold = DEFAULT_RTS_THRESHOLD | RTS_DISABLED; + priv->frag_threshold = DEFAULT_FTS | FRAG_DISABLED; + priv->tx_power = IPW_TX_POWER_DEFAULT; + priv->tx_rates = DEFAULT_TX_RATES; + + strcpy(priv->nick, "ipw2100"); + + spin_lock_init(&priv->low_lock); + sema_init(&priv->action_sem, 1); + sema_init(&priv->adapter_sem, 1); + + init_waitqueue_head(&priv->wait_command_queue); + + netif_carrier_off(dev); + + INIT_LIST_HEAD(&priv->msg_free_list); + INIT_LIST_HEAD(&priv->msg_pend_list); + INIT_STAT(&priv->msg_free_stat); + INIT_STAT(&priv->msg_pend_stat); + + INIT_LIST_HEAD(&priv->tx_free_list); + INIT_LIST_HEAD(&priv->tx_pend_list); + INIT_STAT(&priv->tx_free_stat); + INIT_STAT(&priv->tx_pend_stat); + + INIT_LIST_HEAD(&priv->fw_pend_list); + INIT_STAT(&priv->fw_pend_stat); + + +#ifdef CONFIG_SOFTWARE_SUSPEND2 + priv->workqueue = create_workqueue(DRV_NAME, 0); +#else + priv->workqueue = create_workqueue(DRV_NAME); +#endif + INIT_WORK(&priv->reset_work, + (void (*)(void *))ipw2100_reset_adapter, priv); + INIT_WORK(&priv->security_work, + (void (*)(void *))ipw2100_security_work, priv); + INIT_WORK(&priv->wx_event_work, + (void (*)(void *))ipw2100_wx_event_work, priv); + INIT_WORK(&priv->hang_check, ipw2100_hang_check, priv); + INIT_WORK(&priv->rf_kill, ipw2100_rf_kill, priv); + + tasklet_init(&priv->irq_tasklet, (void (*)(unsigned long)) + ipw2100_irq_tasklet, (unsigned long)priv); + + /* NOTE: We do not start the deferred work for status checks yet */ + priv->stop_rf_kill = 1; + priv->stop_hang_check = 1; + + return dev; +} + + + +#define PCI_DMA_32BIT 0x00000000ffffffffULL + +static int ipw2100_pci_init_one(struct pci_dev *pci_dev, + const struct pci_device_id *ent) +{ + unsigned long mem_start, mem_len, mem_flags; + char *base_addr = NULL; + struct net_device *dev = NULL; + struct ipw2100_priv *priv = NULL; + int err = 0; + int registered = 0; + u32 val; + + IPW_DEBUG_INFO("enter\n"); + + mem_start = pci_resource_start(pci_dev, 0); + mem_len = pci_resource_len(pci_dev, 0); + mem_flags = pci_resource_flags(pci_dev, 0); + + if ((mem_flags & IORESOURCE_MEM) != IORESOURCE_MEM) { + IPW_DEBUG_INFO("weird - resource type is not memory\n"); + err = -ENODEV; + goto fail; + } + + base_addr = ioremap_nocache(mem_start, mem_len); + if (!base_addr) { + printk(KERN_WARNING DRV_NAME + "Error calling ioremap_nocache.\n"); + err = -EIO; + goto fail; + } + + /* allocate and initialize our net_device */ + dev = ipw2100_alloc_device(pci_dev, base_addr, mem_start, mem_len); + if (!dev) { + printk(KERN_WARNING DRV_NAME + "Error calling ipw2100_alloc_device.\n"); + err = -ENOMEM; + goto fail; + } + + /* set up PCI mappings for device */ + err = pci_enable_device(pci_dev); + if (err) { + printk(KERN_WARNING DRV_NAME + "Error calling pci_enable_device.\n"); + return err; + } + + priv = ieee80211_priv(dev); + + pci_set_master(pci_dev); + pci_set_drvdata(pci_dev, priv); + + err = pci_set_dma_mask(pci_dev, PCI_DMA_32BIT); + if (err) { + printk(KERN_WARNING DRV_NAME + "Error calling pci_set_dma_mask.\n"); + pci_disable_device(pci_dev); + return err; + } + + err = pci_request_regions(pci_dev, DRV_NAME); + if (err) { + printk(KERN_WARNING DRV_NAME + "Error calling pci_request_regions.\n"); + pci_disable_device(pci_dev); + return err; + } + + /* We disable the RETRY_TIMEOUT register (0x41) to keep + * PCI Tx retries from interfering with C3 CPU state */ + pci_read_config_dword(pci_dev, 0x40, &val); + if ((val & 0x0000ff00) != 0) + pci_write_config_dword(pci_dev, 0x40, val & 0xffff00ff); + + pci_set_power_state(pci_dev, 0); + + if (!ipw2100_hw_is_adapter_in_system(dev)) { + printk(KERN_WARNING DRV_NAME + "Device not found via register read.\n"); + err = -ENODEV; + goto fail; + } + + SET_NETDEV_DEV(dev, &pci_dev->dev); + + /* Force interrupts to be shut off on the device */ + priv->status |= STATUS_INT_ENABLED; + ipw2100_disable_interrupts(priv); + + /* Allocate and initialize the Tx/Rx queues and lists */ + if (ipw2100_queues_allocate(priv)) { + printk(KERN_WARNING DRV_NAME + "Error calilng ipw2100_queues_allocate.\n"); + err = -ENOMEM; + goto fail; + } + ipw2100_queues_initialize(priv); + + err = request_irq(pci_dev->irq, + ipw2100_interrupt, SA_SHIRQ, + dev->name, priv); + if (err) { + printk(KERN_WARNING DRV_NAME + "Error calling request_irq: %d.\n", + pci_dev->irq); + goto fail; + } + dev->irq = pci_dev->irq; + + IPW_DEBUG_INFO("Attempting to register device...\n"); + + SET_MODULE_OWNER(dev); + + printk(KERN_INFO DRV_NAME + ": Detected Intel PRO/Wireless 2100 Network Connection\n"); + + /* Bring up the interface. Pre 0.46, after we registered the + * network device we would call ipw2100_up. This introduced a race + * condition with newer hotplug configurations (network was coming + * up and making calls before the device was initialized). + * + * If we called ipw2100_up before we registered the device, then the + * device name wasn't registered. So, we instead use the net_dev->init + * member to call a function that then just turns and calls ipw2100_up. + * net_dev->init is called after name allocation but before the + * notifier chain is called */ + down(&priv->action_sem); + err = register_netdev(dev); + if (err) { + printk(KERN_WARNING DRV_NAME + "Error calling register_netdev.\n"); + goto fail_unlock; + } + registered = 1; + + IPW_DEBUG_INFO("%s: Bound to %s\n", dev->name, pci_name(pci_dev)); + + /* perform this after register_netdev so that dev->name is set */ + sysfs_create_group(&pci_dev->dev.kobj, &ipw2100_attribute_group); + netif_carrier_off(dev); + + /* If the RF Kill switch is disabled, go ahead and complete the + * startup sequence */ + if (!(priv->status & STATUS_RF_KILL_MASK)) { + /* Enable the adapter - sends HOST_COMPLETE */ + if (ipw2100_enable_adapter(priv)) { + printk(KERN_WARNING DRV_NAME + ": %s: failed in call to enable adapter.\n", + priv->net_dev->name); + ipw2100_hw_stop_adapter(priv); + err = -EIO; + goto fail_unlock; + } + + /* Start a scan . . . */ + ipw2100_set_scan_options(priv); + ipw2100_start_scan(priv); + } + + IPW_DEBUG_INFO("exit\n"); + + priv->status |= STATUS_INITIALIZED; + + up(&priv->action_sem); + + return 0; + + fail_unlock: + up(&priv->action_sem); + + fail: + if (dev) { + if (registered) + unregister_netdev(dev); + + ipw2100_hw_stop_adapter(priv); + + ipw2100_disable_interrupts(priv); + + if (dev->irq) + free_irq(dev->irq, priv); + + ipw2100_kill_workqueue(priv); + + /* These are safe to call even if they weren't allocated */ + ipw2100_queues_free(priv); + sysfs_remove_group(&pci_dev->dev.kobj, &ipw2100_attribute_group); + + free_ieee80211(dev); + pci_set_drvdata(pci_dev, NULL); + } + + if (base_addr) + iounmap((char*)base_addr); + + pci_release_regions(pci_dev); + pci_disable_device(pci_dev); + + return err; +} + +static void __devexit ipw2100_pci_remove_one(struct pci_dev *pci_dev) +{ + struct ipw2100_priv *priv = pci_get_drvdata(pci_dev); + struct net_device *dev; + + if (priv) { + down(&priv->action_sem); + + priv->status &= ~STATUS_INITIALIZED; + + dev = priv->net_dev; + sysfs_remove_group(&pci_dev->dev.kobj, &ipw2100_attribute_group); + +#ifdef CONFIG_PM + if (ipw2100_firmware.version) + ipw2100_release_firmware(priv, &ipw2100_firmware); +#endif + /* Take down the hardware */ + ipw2100_down(priv); + + /* Release the semaphore so that the network subsystem can + * complete any needed calls into the driver... */ + up(&priv->action_sem); + + /* Unregister the device first - this results in close() + * being called if the device is open. If we free storage + * first, then close() will crash. */ + unregister_netdev(dev); + + /* ipw2100_down will ensure that there is no more pending work + * in the workqueue's, so we can safely remove them now. */ + ipw2100_kill_workqueue(priv); + + ipw2100_queues_free(priv); + + /* Free potential debugging firmware snapshot */ + ipw2100_snapshot_free(priv); + + if (dev->irq) + free_irq(dev->irq, priv); + + if (dev->base_addr) + iounmap((unsigned char *)dev->base_addr); + + free_ieee80211(dev); + } + + pci_release_regions(pci_dev); + pci_disable_device(pci_dev); + + IPW_DEBUG_INFO("exit\n"); +} + + +#ifdef CONFIG_PM +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,11) +static int ipw2100_suspend(struct pci_dev *pci_dev, u32 state) +#else +static int ipw2100_suspend(struct pci_dev *pci_dev, pm_message_t state) +#endif +{ + struct ipw2100_priv *priv = pci_get_drvdata(pci_dev); + struct net_device *dev = priv->net_dev; + + IPW_DEBUG_INFO("%s: Going into suspend...\n", + dev->name); + + down(&priv->action_sem); + if (priv->status & STATUS_INITIALIZED) { + /* Take down the device; powers it off, etc. */ + ipw2100_down(priv); + } + + /* Remove the PRESENT state of the device */ + netif_device_detach(dev); + +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,10) + pci_save_state(pci_dev, priv->pm_state); +#else + pci_save_state(pci_dev); +#endif + pci_disable_device (pci_dev); +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,11) + pci_set_power_state(pci_dev, state); +#else + pci_set_power_state(pci_dev, PCI_D3hot); +#endif + + up(&priv->action_sem); + + return 0; +} + +static int ipw2100_resume(struct pci_dev *pci_dev) +{ + struct ipw2100_priv *priv = pci_get_drvdata(pci_dev); + struct net_device *dev = priv->net_dev; + u32 val; + + if (IPW2100_PM_DISABLED) + return 0; + + down(&priv->action_sem); + + IPW_DEBUG_INFO("%s: Coming out of suspend...\n", + dev->name); + +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,11) + pci_set_power_state(pci_dev, 0); +#else + pci_set_power_state(pci_dev, PCI_D0); +#endif + pci_enable_device(pci_dev); +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,10) + pci_restore_state(pci_dev, priv->pm_state); +#else + pci_restore_state(pci_dev); +#endif + + /* + * Suspend/Resume resets the PCI configuration space, so we have to + * re-disable the RETRY_TIMEOUT register (0x41) to keep PCI Tx retries + * from interfering with C3 CPU state. pci_restore_state won't help + * here since it only restores the first 64 bytes pci config header. + */ + pci_read_config_dword(pci_dev, 0x40, &val); + if ((val & 0x0000ff00) != 0) + pci_write_config_dword(pci_dev, 0x40, val & 0xffff00ff); + + /* Set the device back into the PRESENT state; this will also wake + * the queue of needed */ + netif_device_attach(dev); + + /* Bring the device back up */ + if (!(priv->status & STATUS_RF_KILL_SW)) + ipw2100_up(priv, 0); + + up(&priv->action_sem); + + return 0; +} +#endif + + +#define IPW2100_DEV_ID(x) { PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, x } + +static struct pci_device_id ipw2100_pci_id_table[] __devinitdata = { + IPW2100_DEV_ID(0x2520), /* IN 2100A mPCI 3A */ + IPW2100_DEV_ID(0x2521), /* IN 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2524), /* IN 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2525), /* IN 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2526), /* IN 2100A mPCI Gen A3 */ + IPW2100_DEV_ID(0x2522), /* IN 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2523), /* IN 2100 mPCI 3A */ + IPW2100_DEV_ID(0x2527), /* IN 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2528), /* IN 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2529), /* IN 2100 mPCI 3B */ + IPW2100_DEV_ID(0x252B), /* IN 2100 mPCI 3A */ + IPW2100_DEV_ID(0x252C), /* IN 2100 mPCI 3A */ + IPW2100_DEV_ID(0x252D), /* IN 2100 mPCI 3A */ + + IPW2100_DEV_ID(0x2550), /* IB 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2551), /* IB 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2553), /* IB 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2554), /* IB 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2555), /* IB 2100 mPCI 3B */ + + IPW2100_DEV_ID(0x2560), /* DE 2100A mPCI 3A */ + IPW2100_DEV_ID(0x2562), /* DE 2100A mPCI 3A */ + IPW2100_DEV_ID(0x2563), /* DE 2100A mPCI 3A */ + IPW2100_DEV_ID(0x2561), /* DE 2100 mPCI 3A */ + IPW2100_DEV_ID(0x2565), /* DE 2100 mPCI 3A */ + IPW2100_DEV_ID(0x2566), /* DE 2100 mPCI 3A */ + IPW2100_DEV_ID(0x2567), /* DE 2100 mPCI 3A */ + + IPW2100_DEV_ID(0x2570), /* GA 2100 mPCI 3B */ + + IPW2100_DEV_ID(0x2580), /* TO 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2582), /* TO 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2583), /* TO 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2581), /* TO 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2585), /* TO 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2586), /* TO 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2587), /* TO 2100 mPCI 3B */ + + IPW2100_DEV_ID(0x2590), /* SO 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2592), /* SO 2100A mPCI 3B */ + IPW2100_DEV_ID(0x2591), /* SO 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2593), /* SO 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2596), /* SO 2100 mPCI 3B */ + IPW2100_DEV_ID(0x2598), /* SO 2100 mPCI 3B */ + + IPW2100_DEV_ID(0x25A0), /* HP 2100 mPCI 3B */ + {0,}, +}; + +MODULE_DEVICE_TABLE(pci, ipw2100_pci_id_table); + +static struct pci_driver ipw2100_pci_driver = { + .name = DRV_NAME, + .id_table = ipw2100_pci_id_table, + .probe = ipw2100_pci_init_one, + .remove = __devexit_p(ipw2100_pci_remove_one), +#ifdef CONFIG_PM + .suspend = ipw2100_suspend, + .resume = ipw2100_resume, +#endif +}; + + +/** + * Initialize the ipw2100 driver/module + * + * @returns 0 if ok, < 0 errno node con error. + * + * Note: we cannot init the /proc stuff until the PCI driver is there, + * or we risk an unlikely race condition on someone accessing + * uninitialized data in the PCI dev struct through /proc. + */ +static int __init ipw2100_init(void) +{ + int ret; + + printk(KERN_INFO DRV_NAME ": %s, %s\n", DRV_DESCRIPTION, DRV_VERSION); + printk(KERN_INFO DRV_NAME ": %s\n", DRV_COPYRIGHT); + +#ifdef CONFIG_IEEE80211_NOWEP + IPW_DEBUG_INFO(DRV_NAME ": Compiled with WEP disabled.\n"); +#endif + + ret = pci_module_init(&ipw2100_pci_driver); + +#ifdef CONFIG_IPW_DEBUG + ipw2100_debug_level = debug; + driver_create_file(&ipw2100_pci_driver.driver, + &driver_attr_debug_level); +#endif + + return ret; +} + + +/** + * Cleanup ipw2100 driver registration + */ +static void __exit ipw2100_exit(void) +{ + /* FIXME: IPG: check that we have no instances of the devices open */ +#ifdef CONFIG_IPW_DEBUG + driver_remove_file(&ipw2100_pci_driver.driver, + &driver_attr_debug_level); +#endif + pci_unregister_driver(&ipw2100_pci_driver); +} + +module_init(ipw2100_init); +module_exit(ipw2100_exit); + +#define WEXT_USECHANNELS 1 + +const long ipw2100_frequencies[] = { + 2412, 2417, 2422, 2427, + 2432, 2437, 2442, 2447, + 2452, 2457, 2462, 2467, + 2472, 2484 +}; + +#define FREQ_COUNT (sizeof(ipw2100_frequencies) / \ + sizeof(ipw2100_frequencies[0])) + +const long ipw2100_rates_11b[] = { + 1000000, + 2000000, + 5500000, + 11000000 +}; + +#define RATE_COUNT (sizeof(ipw2100_rates_11b) / sizeof(ipw2100_rates_11b[0])) + +static int ipw2100_wx_get_name(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + if (!(priv->status & STATUS_ASSOCIATED)) + strcpy(wrqu->name, "unassociated"); + else + snprintf(wrqu->name, IFNAMSIZ, "IEEE 802.11b"); + + IPW_DEBUG_WX("Name: %s\n", wrqu->name); + return 0; +} + + +static int ipw2100_wx_set_freq(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct iw_freq *fwrq = &wrqu->freq; + int err = 0; + + if (priv->ieee->iw_mode == IW_MODE_INFRA) + return -EOPNOTSUPP; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + /* if setting by freq convert to channel */ + if (fwrq->e == 1) { + if ((fwrq->m >= (int) 2.412e8 && + fwrq->m <= (int) 2.487e8)) { + int f = fwrq->m / 100000; + int c = 0; + + while ((c < REG_MAX_CHANNEL) && + (f != ipw2100_frequencies[c])) + c++; + + /* hack to fall through */ + fwrq->e = 0; + fwrq->m = c + 1; + } + } + + if (fwrq->e > 0 || fwrq->m > 1000) + return -EOPNOTSUPP; + else { /* Set the channel */ + IPW_DEBUG_WX("SET Freq/Channel -> %d \n", fwrq->m); + err = ipw2100_set_channel(priv, fwrq->m, 0); + } + + done: + up(&priv->action_sem); + return err; +} + + +static int ipw2100_wx_get_freq(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + wrqu->freq.e = 0; + + /* If we are associated, trying to associate, or have a statically + * configured CHANNEL then return that; otherwise return ANY */ + if (priv->config & CFG_STATIC_CHANNEL || + priv->status & STATUS_ASSOCIATED) + wrqu->freq.m = priv->channel; + else + wrqu->freq.m = 0; + + IPW_DEBUG_WX("GET Freq/Channel -> %d \n", priv->channel); + return 0; + +} + +static int ipw2100_wx_set_mode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0; + + IPW_DEBUG_WX("SET Mode -> %d \n", wrqu->mode); + + if (wrqu->mode == priv->ieee->iw_mode) + return 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + switch (wrqu->mode) { +#ifdef CONFIG_IPW2100_MONITOR + case IW_MODE_MONITOR: + err = ipw2100_switch_mode(priv, IW_MODE_MONITOR); + break; +#endif /* CONFIG_IPW2100_MONITOR */ + case IW_MODE_ADHOC: + err = ipw2100_switch_mode(priv, IW_MODE_ADHOC); + break; + case IW_MODE_INFRA: + case IW_MODE_AUTO: + default: + err = ipw2100_switch_mode(priv, IW_MODE_INFRA); + break; + } + +done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_mode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + wrqu->mode = priv->ieee->iw_mode; + IPW_DEBUG_WX("GET Mode -> %d\n", wrqu->mode); + + return 0; +} + + +#define POWER_MODES 5 + +/* Values are in microsecond */ +const s32 timeout_duration[POWER_MODES] = { + 350000, + 250000, + 75000, + 37000, + 25000, +}; + +const s32 period_duration[POWER_MODES] = { + 400000, + 700000, + 1000000, + 1000000, + 1000000 +}; + +static int ipw2100_wx_get_range(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct iw_range *range = (struct iw_range *)extra; + u16 val; + int i, level; + + wrqu->data.length = sizeof(*range); + memset(range, 0, sizeof(*range)); + + /* Let's try to keep this struct in the same order as in + * linux/include/wireless.h + */ + + /* TODO: See what values we can set, and remove the ones we can't + * set, or fill them with some default data. + */ + + /* ~5 Mb/s real (802.11b) */ + range->throughput = 5 * 1000 * 1000; + +// range->sensitivity; /* signal level threshold range */ + + range->max_qual.qual = 100; + /* TODO: Find real max RSSI and stick here */ + range->max_qual.level = 0; + range->max_qual.noise = 0; + range->max_qual.updated = 7; /* Updated all three */ + + range->avg_qual.qual = 70; /* > 8% missed beacons is 'bad' */ + /* TODO: Find real 'good' to 'bad' threshol value for RSSI */ + range->avg_qual.level = 20 + IPW2100_RSSI_TO_DBM; + range->avg_qual.noise = 0; + range->avg_qual.updated = 7; /* Updated all three */ + + range->num_bitrates = RATE_COUNT; + + for (i = 0; i < RATE_COUNT && i < IW_MAX_BITRATES; i++) { + range->bitrate[i] = ipw2100_rates_11b[i]; + } + + range->min_rts = MIN_RTS_THRESHOLD; + range->max_rts = MAX_RTS_THRESHOLD; + range->min_frag = MIN_FRAG_THRESHOLD; + range->max_frag = MAX_FRAG_THRESHOLD; + + range->min_pmp = period_duration[0]; /* Minimal PM period */ + range->max_pmp = period_duration[POWER_MODES-1];/* Maximal PM period */ + range->min_pmt = timeout_duration[POWER_MODES-1]; /* Minimal PM timeout */ + range->max_pmt = timeout_duration[0];/* Maximal PM timeout */ + + /* How to decode max/min PM period */ + range->pmp_flags = IW_POWER_PERIOD; + /* How to decode max/min PM period */ + range->pmt_flags = IW_POWER_TIMEOUT; + /* What PM options are supported */ + range->pm_capa = IW_POWER_TIMEOUT | IW_POWER_PERIOD; + + range->encoding_size[0] = 5; + range->encoding_size[1] = 13; /* Different token sizes */ + range->num_encoding_sizes = 2; /* Number of entry in the list */ + range->max_encoding_tokens = WEP_KEYS; /* Max number of tokens */ +// range->encoding_login_index; /* token index for login token */ + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) { + range->txpower_capa = IW_TXPOW_DBM; + range->num_txpower = IW_MAX_TXPOWER; + for (i = 0, level = (IPW_TX_POWER_MAX_DBM * 16); i < IW_MAX_TXPOWER; + i++, level -= ((IPW_TX_POWER_MAX_DBM - IPW_TX_POWER_MIN_DBM) * 16) / + (IW_MAX_TXPOWER - 1)) + range->txpower[i] = level / 16; + } else { + range->txpower_capa = 0; + range->num_txpower = 0; + } + + + /* Set the Wireless Extension versions */ + range->we_version_compiled = WIRELESS_EXT; + range->we_version_source = 16; + +// range->retry_capa; /* What retry options are supported */ +// range->retry_flags; /* How to decode max/min retry limit */ +// range->r_time_flags; /* How to decode max/min retry life */ +// range->min_retry; /* Minimal number of retries */ +// range->max_retry; /* Maximal number of retries */ +// range->min_r_time; /* Minimal retry lifetime */ +// range->max_r_time; /* Maximal retry lifetime */ + + range->num_channels = FREQ_COUNT; + + val = 0; + for (i = 0; i < FREQ_COUNT; i++) { + // TODO: Include only legal frequencies for some countries +// if (local->channel_mask & (1 << i)) { + range->freq[val].i = i + 1; + range->freq[val].m = ipw2100_frequencies[i] * 100000; + range->freq[val].e = 1; + val++; +// } + if (val == IW_MAX_FREQUENCIES) + break; + } + range->num_frequency = val; + + IPW_DEBUG_WX("GET Range\n"); + + return 0; +} + +static int ipw2100_wx_set_wap(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0; + + static const unsigned char any[] = { + 0xff, 0xff, 0xff, 0xff, 0xff, 0xff + }; + static const unsigned char off[] = { + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + }; + + // sanity checks + if (wrqu->ap_addr.sa_family != ARPHRD_ETHER) + return -EINVAL; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (!memcmp(any, wrqu->ap_addr.sa_data, ETH_ALEN) || + !memcmp(off, wrqu->ap_addr.sa_data, ETH_ALEN)) { + /* we disable mandatory BSSID association */ + IPW_DEBUG_WX("exit - disable mandatory BSSID\n"); + priv->config &= ~CFG_STATIC_BSSID; + err = ipw2100_set_mandatory_bssid(priv, NULL, 0); + goto done; + } + + priv->config |= CFG_STATIC_BSSID; + memcpy(priv->mandatory_bssid_mac, wrqu->ap_addr.sa_data, ETH_ALEN); + + err = ipw2100_set_mandatory_bssid(priv, wrqu->ap_addr.sa_data, 0); + + IPW_DEBUG_WX("SET BSSID -> %02X:%02X:%02X:%02X:%02X:%02X\n", + wrqu->ap_addr.sa_data[0] & 0xff, + wrqu->ap_addr.sa_data[1] & 0xff, + wrqu->ap_addr.sa_data[2] & 0xff, + wrqu->ap_addr.sa_data[3] & 0xff, + wrqu->ap_addr.sa_data[4] & 0xff, + wrqu->ap_addr.sa_data[5] & 0xff); + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_wap(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + /* If we are associated, trying to associate, or have a statically + * configured BSSID then return that; otherwise return ANY */ + if (priv->config & CFG_STATIC_BSSID || + priv->status & STATUS_ASSOCIATED) { + wrqu->ap_addr.sa_family = ARPHRD_ETHER; + memcpy(wrqu->ap_addr.sa_data, &priv->bssid, ETH_ALEN); + } else + memset(wrqu->ap_addr.sa_data, 0, ETH_ALEN); + + IPW_DEBUG_WX("Getting WAP BSSID: " MAC_FMT "\n", + MAC_ARG(wrqu->ap_addr.sa_data)); + return 0; +} + +static int ipw2100_wx_set_essid(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + char *essid = ""; /* ANY */ + int length = 0; + int err = 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (wrqu->essid.flags && wrqu->essid.length) { + length = wrqu->essid.length - 1; + essid = extra; + } + + if (length == 0) { + IPW_DEBUG_WX("Setting ESSID to ANY\n"); + priv->config &= ~CFG_STATIC_ESSID; + err = ipw2100_set_essid(priv, NULL, 0, 0); + goto done; + } + + length = min(length, IW_ESSID_MAX_SIZE); + + priv->config |= CFG_STATIC_ESSID; + + if (priv->essid_len == length && !memcmp(priv->essid, extra, length)) { + IPW_DEBUG_WX("ESSID set to current ESSID.\n"); + err = 0; + goto done; + } + + IPW_DEBUG_WX("Setting ESSID: '%s' (%d)\n", escape_essid(essid, length), + length); + + priv->essid_len = length; + memcpy(priv->essid, essid, priv->essid_len); + + err = ipw2100_set_essid(priv, essid, length, 0); + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_essid(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + /* If we are associated, trying to associate, or have a statically + * configured ESSID then return that; otherwise return ANY */ + if (priv->config & CFG_STATIC_ESSID || + priv->status & STATUS_ASSOCIATED) { + IPW_DEBUG_WX("Getting essid: '%s'\n", + escape_essid(priv->essid, priv->essid_len)); + memcpy(extra, priv->essid, priv->essid_len); + wrqu->essid.length = priv->essid_len; + wrqu->essid.flags = 1; /* active */ + } else { + IPW_DEBUG_WX("Getting essid: ANY\n"); + wrqu->essid.length = 0; + wrqu->essid.flags = 0; /* active */ + } + + return 0; +} + +static int ipw2100_wx_set_nick(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + if (wrqu->data.length > IW_ESSID_MAX_SIZE) + return -E2BIG; + + wrqu->data.length = min((size_t)wrqu->data.length, sizeof(priv->nick)); + memset(priv->nick, 0, sizeof(priv->nick)); + memcpy(priv->nick, extra, wrqu->data.length); + + IPW_DEBUG_WX("SET Nickname -> %s \n", priv->nick); + + return 0; +} + +static int ipw2100_wx_get_nick(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + wrqu->data.length = strlen(priv->nick) + 1; + memcpy(extra, priv->nick, wrqu->data.length); + wrqu->data.flags = 1; /* active */ + + IPW_DEBUG_WX("GET Nickname -> %s \n", extra); + + return 0; +} + +static int ipw2100_wx_set_rate(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + u32 target_rate = wrqu->bitrate.value; + u32 rate; + int err = 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + rate = 0; + + if (target_rate == 1000000 || + (!wrqu->bitrate.fixed && target_rate > 1000000)) + rate |= TX_RATE_1_MBIT; + if (target_rate == 2000000 || + (!wrqu->bitrate.fixed && target_rate > 2000000)) + rate |= TX_RATE_2_MBIT; + if (target_rate == 5500000 || + (!wrqu->bitrate.fixed && target_rate > 5500000)) + rate |= TX_RATE_5_5_MBIT; + if (target_rate == 11000000 || + (!wrqu->bitrate.fixed && target_rate > 11000000)) + rate |= TX_RATE_11_MBIT; + if (rate == 0) + rate = DEFAULT_TX_RATES; + + err = ipw2100_set_tx_rates(priv, rate, 0); + + IPW_DEBUG_WX("SET Rate -> %04X \n", rate); + done: + up(&priv->action_sem); + return err; +} + + +static int ipw2100_wx_get_rate(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int val; + int len = sizeof(val); + int err = 0; + + if (!(priv->status & STATUS_ENABLED) || + priv->status & STATUS_RF_KILL_MASK || + !(priv->status & STATUS_ASSOCIATED)) { + wrqu->bitrate.value = 0; + return 0; + } + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + err = ipw2100_get_ordinal(priv, IPW_ORD_CURRENT_TX_RATE, &val, &len); + if (err) { + IPW_DEBUG_WX("failed querying ordinals.\n"); + return err; + } + + switch (val & TX_RATE_MASK) { + case TX_RATE_1_MBIT: + wrqu->bitrate.value = 1000000; + break; + case TX_RATE_2_MBIT: + wrqu->bitrate.value = 2000000; + break; + case TX_RATE_5_5_MBIT: + wrqu->bitrate.value = 5500000; + break; + case TX_RATE_11_MBIT: + wrqu->bitrate.value = 11000000; + break; + default: + wrqu->bitrate.value = 0; + } + + IPW_DEBUG_WX("GET Rate -> %d \n", wrqu->bitrate.value); + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_set_rts(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int value, err; + + /* Auto RTS not yet supported */ + if (wrqu->rts.fixed == 0) + return -EINVAL; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (wrqu->rts.disabled) + value = priv->rts_threshold | RTS_DISABLED; + else { + if (wrqu->rts.value < 1 || + wrqu->rts.value > 2304) { + err = -EINVAL; + goto done; + } + value = wrqu->rts.value; + } + + err = ipw2100_set_rts_threshold(priv, value); + + IPW_DEBUG_WX("SET RTS Threshold -> 0x%08X \n", value); + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_rts(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + wrqu->rts.value = priv->rts_threshold & ~RTS_DISABLED; + wrqu->rts.fixed = 1; /* no auto select */ + + /* If RTS is set to the default value, then it is disabled */ + wrqu->rts.disabled = (priv->rts_threshold & RTS_DISABLED) ? 1 : 0; + + IPW_DEBUG_WX("GET RTS Threshold -> 0x%08X \n", wrqu->rts.value); + + return 0; +} + +static int ipw2100_wx_set_txpow(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0, value; + + if (priv->ieee->iw_mode != IW_MODE_ADHOC) + return -EINVAL; + + if (wrqu->txpower.disabled == 1 || wrqu->txpower.fixed == 0) + value = IPW_TX_POWER_DEFAULT; + else { + if (wrqu->txpower.value < IPW_TX_POWER_MIN_DBM || + wrqu->txpower.value > IPW_TX_POWER_MAX_DBM) + return -EINVAL; + + value = (wrqu->txpower.value - IPW_TX_POWER_MIN_DBM) * 16 / + (IPW_TX_POWER_MAX_DBM - IPW_TX_POWER_MIN_DBM); + } + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + err = ipw2100_set_tx_power(priv, value); + + IPW_DEBUG_WX("SET TX Power -> %d \n", value); + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_txpow(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + if (priv->ieee->iw_mode != IW_MODE_ADHOC) { + wrqu->power.disabled = 1; + return 0; + } + + if (priv->tx_power == IPW_TX_POWER_DEFAULT) { + wrqu->power.fixed = 0; + wrqu->power.value = IPW_TX_POWER_MAX_DBM; + wrqu->power.disabled = 1; + } else { + wrqu->power.disabled = 0; + wrqu->power.fixed = 1; + wrqu->power.value = + (priv->tx_power * + (IPW_TX_POWER_MAX_DBM - IPW_TX_POWER_MIN_DBM)) / + (IPW_TX_POWER_MAX - IPW_TX_POWER_MIN) + + IPW_TX_POWER_MIN_DBM; + } + + wrqu->power.flags = IW_TXPOW_DBM; + + IPW_DEBUG_WX("GET TX Power -> %d \n", wrqu->power.value); + + return 0; +} + +static int ipw2100_wx_set_frag(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + if (!wrqu->frag.fixed) + return -EINVAL; + + if (wrqu->frag.disabled) { + priv->frag_threshold |= FRAG_DISABLED; + priv->ieee->fts = DEFAULT_FTS; + } else { + if (wrqu->frag.value < MIN_FRAG_THRESHOLD || + wrqu->frag.value > MAX_FRAG_THRESHOLD) + return -EINVAL; + + priv->ieee->fts = wrqu->frag.value & ~0x1; + priv->frag_threshold = priv->ieee->fts; + } + + IPW_DEBUG_WX("SET Frag Threshold -> %d \n", priv->ieee->fts); + + return 0; +} + +static int ipw2100_wx_get_frag(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + wrqu->frag.value = priv->frag_threshold & ~FRAG_DISABLED; + wrqu->frag.fixed = 0; /* no auto select */ + wrqu->frag.disabled = (priv->frag_threshold & FRAG_DISABLED) ? 1 : 0; + + IPW_DEBUG_WX("GET Frag Threshold -> %d \n", wrqu->frag.value); + + return 0; +} + +static int ipw2100_wx_set_retry(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0; + + if (wrqu->retry.flags & IW_RETRY_LIFETIME || + wrqu->retry.disabled) + return -EINVAL; + + if (!(wrqu->retry.flags & IW_RETRY_LIMIT)) + return 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (wrqu->retry.flags & IW_RETRY_MIN) { + err = ipw2100_set_short_retry(priv, wrqu->retry.value); + IPW_DEBUG_WX("SET Short Retry Limit -> %d \n", + wrqu->retry.value); + goto done; + } + + if (wrqu->retry.flags & IW_RETRY_MAX) { + err = ipw2100_set_long_retry(priv, wrqu->retry.value); + IPW_DEBUG_WX("SET Long Retry Limit -> %d \n", + wrqu->retry.value); + goto done; + } + + err = ipw2100_set_short_retry(priv, wrqu->retry.value); + if (!err) + err = ipw2100_set_long_retry(priv, wrqu->retry.value); + + IPW_DEBUG_WX("SET Both Retry Limits -> %d \n", wrqu->retry.value); + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_retry(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + wrqu->retry.disabled = 0; /* can't be disabled */ + + if ((wrqu->retry.flags & IW_RETRY_TYPE) == + IW_RETRY_LIFETIME) + return -EINVAL; + + if (wrqu->retry.flags & IW_RETRY_MAX) { + wrqu->retry.flags = IW_RETRY_LIMIT & IW_RETRY_MAX; + wrqu->retry.value = priv->long_retry_limit; + } else { + wrqu->retry.flags = + (priv->short_retry_limit != + priv->long_retry_limit) ? + IW_RETRY_LIMIT & IW_RETRY_MIN : IW_RETRY_LIMIT; + + wrqu->retry.value = priv->short_retry_limit; + } + + IPW_DEBUG_WX("GET Retry -> %d \n", wrqu->retry.value); + + return 0; +} + +static int ipw2100_wx_set_scan(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + IPW_DEBUG_WX("Initiating scan...\n"); + if (ipw2100_set_scan_options(priv) || + ipw2100_start_scan(priv)) { + IPW_DEBUG_WX("Start scan failed.\n"); + + /* TODO: Mark a scan as pending so when hardware initialized + * a scan starts */ + } + + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_scan(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + return ieee80211_wx_get_scan(priv->ieee, info, wrqu, extra); +} + + +/* + * Implementation based on code in hostap-driver v0.1.3 hostap_ioctl.c + */ +static int ipw2100_wx_set_encode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key) +{ + /* + * No check of STATUS_INITIALIZED required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + return ieee80211_wx_set_encode(priv->ieee, info, wrqu, key); +} + +static int ipw2100_wx_get_encode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + return ieee80211_wx_get_encode(priv->ieee, info, wrqu, key); +} + +static int ipw2100_wx_set_power(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (wrqu->power.disabled) { + priv->power_mode = IPW_POWER_LEVEL(priv->power_mode); + err = ipw2100_set_power_mode(priv, IPW_POWER_MODE_CAM); + IPW_DEBUG_WX("SET Power Management Mode -> off\n"); + goto done; + } + + switch (wrqu->power.flags & IW_POWER_MODE) { + case IW_POWER_ON: /* If not specified */ + case IW_POWER_MODE: /* If set all mask */ + case IW_POWER_ALL_R: /* If explicitely state all */ + break; + default: /* Otherwise we don't support it */ + IPW_DEBUG_WX("SET PM Mode: %X not supported.\n", + wrqu->power.flags); + err = -EOPNOTSUPP; + goto done; + } + + /* If the user hasn't specified a power management mode yet, default + * to BATTERY */ + priv->power_mode = IPW_POWER_ENABLED | priv->power_mode; + err = ipw2100_set_power_mode(priv, IPW_POWER_LEVEL(priv->power_mode)); + + IPW_DEBUG_WX("SET Power Management Mode -> 0x%02X\n", + priv->power_mode); + + done: + up(&priv->action_sem); + return err; + +} + +static int ipw2100_wx_get_power(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + if (!(priv->power_mode & IPW_POWER_ENABLED)) { + wrqu->power.disabled = 1; + } else { + wrqu->power.disabled = 0; + wrqu->power.flags = 0; + } + + IPW_DEBUG_WX("GET Power Management Mode -> %02X\n", priv->power_mode); + + return 0; +} + + +/* + * + * IWPRIV handlers + * + */ +#ifdef CONFIG_IPW2100_MONITOR +static int ipw2100_wx_set_promisc(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int *parms = (int *)extra; + int enable = (parms[0] > 0); + int err = 0; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (enable) { + if (priv->ieee->iw_mode == IW_MODE_MONITOR) { + err = ipw2100_set_channel(priv, parms[1], 0); + goto done; + } + priv->channel = parms[1]; + err = ipw2100_switch_mode(priv, IW_MODE_MONITOR); + } else { + if (priv->ieee->iw_mode == IW_MODE_MONITOR) + err = ipw2100_switch_mode(priv, priv->last_mode); + } + done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_reset(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + if (priv->status & STATUS_INITIALIZED) + schedule_reset(priv); + return 0; +} + +#endif + +static int ipw2100_wx_set_powermode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err = 0, mode = *(int *)extra; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if ((mode < 1) || (mode > POWER_MODES)) + mode = IPW_POWER_AUTO; + + if (priv->power_mode != mode) + err = ipw2100_set_power_mode(priv, mode); + done: + up(&priv->action_sem); + return err; +} + +#define MAX_POWER_STRING 80 +static int ipw2100_wx_get_powermode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + int level = IPW_POWER_LEVEL(priv->power_mode); + s32 timeout, period; + + if (!(priv->power_mode & IPW_POWER_ENABLED)) { + snprintf(extra, MAX_POWER_STRING, + "Power save level: %d (Off)", level); + } else { + switch (level) { + case IPW_POWER_MODE_CAM: + snprintf(extra, MAX_POWER_STRING, + "Power save level: %d (None)", level); + break; + case IPW_POWER_AUTO: + snprintf(extra, MAX_POWER_STRING, + "Power save level: %d (Auto)", 0); + break; + default: + timeout = timeout_duration[level - 1] / 1000; + period = period_duration[level - 1] / 1000; + snprintf(extra, MAX_POWER_STRING, + "Power save level: %d " + "(Timeout %dms, Period %dms)", + level, timeout, period); + } + } + + wrqu->data.length = strlen(extra) + 1; + + return 0; +} + + +static int ipw2100_wx_set_preamble(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw2100_priv *priv = ieee80211_priv(dev); + int err, mode = *(int *)extra; + + down(&priv->action_sem); + if (!(priv->status & STATUS_INITIALIZED)) { + err = -EIO; + goto done; + } + + if (mode == 1) + priv->config |= CFG_LONG_PREAMBLE; + else if (mode == 0) + priv->config &= ~CFG_LONG_PREAMBLE; + else { + err = -EINVAL; + goto done; + } + + err = ipw2100_system_config(priv, 0); + +done: + up(&priv->action_sem); + return err; +} + +static int ipw2100_wx_get_preamble(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + /* + * This can be called at any time. No action lock required + */ + + struct ipw2100_priv *priv = ieee80211_priv(dev); + + if (priv->config & CFG_LONG_PREAMBLE) + snprintf(wrqu->name, IFNAMSIZ, "long (1)"); + else + snprintf(wrqu->name, IFNAMSIZ, "auto (0)"); + + return 0; +} + +static iw_handler ipw2100_wx_handlers[] = +{ + NULL, /* SIOCSIWCOMMIT */ + ipw2100_wx_get_name, /* SIOCGIWNAME */ + NULL, /* SIOCSIWNWID */ + NULL, /* SIOCGIWNWID */ + ipw2100_wx_set_freq, /* SIOCSIWFREQ */ + ipw2100_wx_get_freq, /* SIOCGIWFREQ */ + ipw2100_wx_set_mode, /* SIOCSIWMODE */ + ipw2100_wx_get_mode, /* SIOCGIWMODE */ + NULL, /* SIOCSIWSENS */ + NULL, /* SIOCGIWSENS */ + NULL, /* SIOCSIWRANGE */ + ipw2100_wx_get_range, /* SIOCGIWRANGE */ + NULL, /* SIOCSIWPRIV */ + NULL, /* SIOCGIWPRIV */ + NULL, /* SIOCSIWSTATS */ + NULL, /* SIOCGIWSTATS */ + NULL, /* SIOCSIWSPY */ + NULL, /* SIOCGIWSPY */ + NULL, /* SIOCGIWTHRSPY */ + NULL, /* SIOCWIWTHRSPY */ + ipw2100_wx_set_wap, /* SIOCSIWAP */ + ipw2100_wx_get_wap, /* SIOCGIWAP */ + NULL, /* -- hole -- */ + NULL, /* SIOCGIWAPLIST -- depricated */ + ipw2100_wx_set_scan, /* SIOCSIWSCAN */ + ipw2100_wx_get_scan, /* SIOCGIWSCAN */ + ipw2100_wx_set_essid, /* SIOCSIWESSID */ + ipw2100_wx_get_essid, /* SIOCGIWESSID */ + ipw2100_wx_set_nick, /* SIOCSIWNICKN */ + ipw2100_wx_get_nick, /* SIOCGIWNICKN */ + NULL, /* -- hole -- */ + NULL, /* -- hole -- */ + ipw2100_wx_set_rate, /* SIOCSIWRATE */ + ipw2100_wx_get_rate, /* SIOCGIWRATE */ + ipw2100_wx_set_rts, /* SIOCSIWRTS */ + ipw2100_wx_get_rts, /* SIOCGIWRTS */ + ipw2100_wx_set_frag, /* SIOCSIWFRAG */ + ipw2100_wx_get_frag, /* SIOCGIWFRAG */ + ipw2100_wx_set_txpow, /* SIOCSIWTXPOW */ + ipw2100_wx_get_txpow, /* SIOCGIWTXPOW */ + ipw2100_wx_set_retry, /* SIOCSIWRETRY */ + ipw2100_wx_get_retry, /* SIOCGIWRETRY */ + ipw2100_wx_set_encode, /* SIOCSIWENCODE */ + ipw2100_wx_get_encode, /* SIOCGIWENCODE */ + ipw2100_wx_set_power, /* SIOCSIWPOWER */ + ipw2100_wx_get_power, /* SIOCGIWPOWER */ +}; + +#define IPW2100_PRIV_SET_MONITOR SIOCIWFIRSTPRIV +#define IPW2100_PRIV_RESET SIOCIWFIRSTPRIV+1 +#define IPW2100_PRIV_SET_POWER SIOCIWFIRSTPRIV+2 +#define IPW2100_PRIV_GET_POWER SIOCIWFIRSTPRIV+3 +#define IPW2100_PRIV_SET_LONGPREAMBLE SIOCIWFIRSTPRIV+4 +#define IPW2100_PRIV_GET_LONGPREAMBLE SIOCIWFIRSTPRIV+5 + +static const struct iw_priv_args ipw2100_private_args[] = { + +#ifdef CONFIG_IPW2100_MONITOR + { + IPW2100_PRIV_SET_MONITOR, + IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 2, 0, "monitor" + }, + { + IPW2100_PRIV_RESET, + IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 0, 0, "reset" + }, +#endif /* CONFIG_IPW2100_MONITOR */ + + { + IPW2100_PRIV_SET_POWER, + IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1, 0, "set_power" + }, + { + IPW2100_PRIV_GET_POWER, + 0, IW_PRIV_TYPE_CHAR | IW_PRIV_SIZE_FIXED | MAX_POWER_STRING, "get_power" + }, + { + IPW2100_PRIV_SET_LONGPREAMBLE, + IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1, 0, "set_preamble" + }, + { + IPW2100_PRIV_GET_LONGPREAMBLE, + 0, IW_PRIV_TYPE_CHAR | IW_PRIV_SIZE_FIXED | IFNAMSIZ, "get_preamble" + }, +}; + +static iw_handler ipw2100_private_handler[] = { +#ifdef CONFIG_IPW2100_MONITOR + ipw2100_wx_set_promisc, + ipw2100_wx_reset, +#else /* CONFIG_IPW2100_MONITOR */ + NULL, + NULL, +#endif /* CONFIG_IPW2100_MONITOR */ + ipw2100_wx_set_powermode, + ipw2100_wx_get_powermode, + ipw2100_wx_set_preamble, + ipw2100_wx_get_preamble, +}; + +struct iw_handler_def ipw2100_wx_handler_def = +{ + .standard = ipw2100_wx_handlers, + .num_standard = sizeof(ipw2100_wx_handlers) / sizeof(iw_handler), + .num_private = sizeof(ipw2100_private_handler) / sizeof(iw_handler), + .num_private_args = sizeof(ipw2100_private_args) / + sizeof(struct iw_priv_args), + .private = (iw_handler *)ipw2100_private_handler, + .private_args = (struct iw_priv_args *)ipw2100_private_args, +}; + +/* + * Get wireless statistics. + * Called by /proc/net/wireless + * Also called by SIOCGIWSTATS + */ +struct iw_statistics *ipw2100_wx_wireless_stats(struct net_device * dev) +{ + enum { + POOR = 30, + FAIR = 60, + GOOD = 80, + VERY_GOOD = 90, + EXCELLENT = 95, + PERFECT = 100 + }; + int rssi_qual; + int tx_qual; + int beacon_qual; + + struct ipw2100_priv *priv = ieee80211_priv(dev); + struct iw_statistics *wstats; + u32 rssi, quality, tx_retries, missed_beacons, tx_failures; + u32 ord_len = sizeof(u32); + + if (!priv) + return (struct iw_statistics *) NULL; + + wstats = &priv->wstats; + + /* if hw is disabled, then ipw2100_get_ordinal() can't be called. + * ipw2100_wx_wireless_stats seems to be called before fw is + * initialized. STATUS_ASSOCIATED will only be set if the hw is up + * and associated; if not associcated, the values are all meaningless + * anyway, so set them all to NULL and INVALID */ + if (!(priv->status & STATUS_ASSOCIATED)) { + wstats->miss.beacon = 0; + wstats->discard.retries = 0; + wstats->qual.qual = 0; + wstats->qual.level = 0; + wstats->qual.noise = 0; + wstats->qual.updated = 7; + wstats->qual.updated |= IW_QUAL_NOISE_INVALID | + IW_QUAL_QUAL_INVALID | IW_QUAL_LEVEL_INVALID; + return wstats; + } + + if (ipw2100_get_ordinal(priv, IPW_ORD_STAT_PERCENT_MISSED_BCNS, + &missed_beacons, &ord_len)) + goto fail_get_ordinal; + + /* If we don't have a connection the quality and level is 0*/ + if (!(priv->status & STATUS_ASSOCIATED)) { + wstats->qual.qual = 0; + wstats->qual.level = 0; + } else { + if (ipw2100_get_ordinal(priv, IPW_ORD_RSSI_AVG_CURR, + &rssi, &ord_len)) + goto fail_get_ordinal; + wstats->qual.level = rssi + IPW2100_RSSI_TO_DBM; + if (rssi < 10) + rssi_qual = rssi * POOR / 10; + else if (rssi < 15) + rssi_qual = (rssi - 10) * (FAIR - POOR) / 5 + POOR; + else if (rssi < 20) + rssi_qual = (rssi - 15) * (GOOD - FAIR) / 5 + FAIR; + else if (rssi < 30) + rssi_qual = (rssi - 20) * (VERY_GOOD - GOOD) / + 10 + GOOD; + else + rssi_qual = (rssi - 30) * (PERFECT - VERY_GOOD) / + 10 + VERY_GOOD; + + if (ipw2100_get_ordinal(priv, IPW_ORD_STAT_PERCENT_RETRIES, + &tx_retries, &ord_len)) + goto fail_get_ordinal; + + if (tx_retries > 75) + tx_qual = (90 - tx_retries) * POOR / 15; + else if (tx_retries > 70) + tx_qual = (75 - tx_retries) * (FAIR - POOR) / 5 + POOR; + else if (tx_retries > 65) + tx_qual = (70 - tx_retries) * (GOOD - FAIR) / 5 + FAIR; + else if (tx_retries > 50) + tx_qual = (65 - tx_retries) * (VERY_GOOD - GOOD) / + 15 + GOOD; + else + tx_qual = (50 - tx_retries) * + (PERFECT - VERY_GOOD) / 50 + VERY_GOOD; + + if (missed_beacons > 50) + beacon_qual = (60 - missed_beacons) * POOR / 10; + else if (missed_beacons > 40) + beacon_qual = (50 - missed_beacons) * (FAIR - POOR) / + 10 + POOR; + else if (missed_beacons > 32) + beacon_qual = (40 - missed_beacons) * (GOOD - FAIR) / + 18 + FAIR; + else if (missed_beacons > 20) + beacon_qual = (32 - missed_beacons) * + (VERY_GOOD - GOOD) / 20 + GOOD; + else + beacon_qual = (20 - missed_beacons) * + (PERFECT - VERY_GOOD) / 20 + VERY_GOOD; + + quality = min(beacon_qual, min(tx_qual, rssi_qual)); + +#ifdef CONFIG_IPW_DEBUG + if (beacon_qual == quality) + IPW_DEBUG_WX("Quality clamped by Missed Beacons\n"); + else if (tx_qual == quality) + IPW_DEBUG_WX("Quality clamped by Tx Retries\n"); + else if (quality != 100) + IPW_DEBUG_WX("Quality clamped by Signal Strength\n"); + else + IPW_DEBUG_WX("Quality not clamped.\n"); +#endif + + wstats->qual.qual = quality; + wstats->qual.level = rssi + IPW2100_RSSI_TO_DBM; + } + + wstats->qual.noise = 0; + wstats->qual.updated = 7; + wstats->qual.updated |= IW_QUAL_NOISE_INVALID; + + /* FIXME: this is percent and not a # */ + wstats->miss.beacon = missed_beacons; + + if (ipw2100_get_ordinal(priv, IPW_ORD_STAT_TX_FAILURES, + &tx_failures, &ord_len)) + goto fail_get_ordinal; + wstats->discard.retries = tx_failures; + + return wstats; + + fail_get_ordinal: + IPW_DEBUG_WX("failed querying ordinals.\n"); + + return (struct iw_statistics *) NULL; +} + +void ipw2100_wx_event_work(struct ipw2100_priv *priv) +{ + union iwreq_data wrqu; + int len = ETH_ALEN; + + if (priv->status & STATUS_STOPPING) + return; + + down(&priv->action_sem); + + IPW_DEBUG_WX("enter\n"); + + up(&priv->action_sem); + + wrqu.ap_addr.sa_family = ARPHRD_ETHER; + + /* Fetch BSSID from the hardware */ + if (!(priv->status & (STATUS_ASSOCIATING | STATUS_ASSOCIATED)) || + priv->status & STATUS_RF_KILL_MASK || + ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_AP_BSSID, + &priv->bssid, &len)) { + memset(wrqu.ap_addr.sa_data, 0, ETH_ALEN); + } else { + /* We now have the BSSID, so can finish setting to the full + * associated state */ + memcpy(wrqu.ap_addr.sa_data, priv->bssid, ETH_ALEN); + memcpy(&priv->ieee->bssid, priv->bssid, ETH_ALEN); + priv->status &= ~STATUS_ASSOCIATING; + priv->status |= STATUS_ASSOCIATED; + netif_carrier_on(priv->net_dev); + if (netif_queue_stopped(priv->net_dev)) { + IPW_DEBUG_INFO("Waking net queue.\n"); + netif_wake_queue(priv->net_dev); + } else { + IPW_DEBUG_INFO("Starting net queue.\n"); + netif_start_queue(priv->net_dev); + } + } + + if (!(priv->status & STATUS_ASSOCIATED)) { + IPW_DEBUG_WX("Configuring ESSID\n"); + down(&priv->action_sem); + /* This is a disassociation event, so kick the firmware to + * look for another AP */ + if (priv->config & CFG_STATIC_ESSID) + ipw2100_set_essid(priv, priv->essid, priv->essid_len, 0); + else + ipw2100_set_essid(priv, NULL, 0, 0); + up(&priv->action_sem); + } + + wireless_send_event(priv->net_dev, SIOCGIWAP, &wrqu, NULL); +} + +#define IPW2100_FW_MAJOR_VERSION 1 +#define IPW2100_FW_MINOR_VERSION 3 + +#define IPW2100_FW_MINOR(x) ((x & 0xff) >> 8) +#define IPW2100_FW_MAJOR(x) (x & 0xff) + +#define IPW2100_FW_VERSION ((IPW2100_FW_MINOR_VERSION << 8) | \ + IPW2100_FW_MAJOR_VERSION) + +#define IPW2100_FW_PREFIX "ipw2100-" __stringify(IPW2100_FW_MAJOR_VERSION) \ +"." __stringify(IPW2100_FW_MINOR_VERSION) + +#define IPW2100_FW_NAME(x) IPW2100_FW_PREFIX "" x ".fw" + + +/* + +BINARY FIRMWARE HEADER FORMAT + +offset length desc +0 2 version +2 2 mode == 0:BSS,1:IBSS,2:MONITOR +4 4 fw_len +8 4 uc_len +C fw_len firmware data +12 + fw_len uc_len microcode data + +*/ + +struct ipw2100_fw_header { + short version; + short mode; + unsigned int fw_size; + unsigned int uc_size; +} __attribute__ ((packed)); + + + +static int ipw2100_mod_firmware_load(struct ipw2100_fw *fw) +{ + struct ipw2100_fw_header *h = + (struct ipw2100_fw_header *)fw->fw_entry->data; + + if (IPW2100_FW_MAJOR(h->version) != IPW2100_FW_MAJOR_VERSION) { + IPW_DEBUG_WARNING("Firmware image not compatible " + "(detected version id of %u). " + "See Documentation/networking/README.ipw2100\n", + h->version); + return 1; + } + + fw->version = h->version; + fw->fw.data = fw->fw_entry->data + sizeof(struct ipw2100_fw_header); + fw->fw.size = h->fw_size; + fw->uc.data = fw->fw.data + h->fw_size; + fw->uc.size = h->uc_size; + + return 0; +} + + +int ipw2100_get_firmware(struct ipw2100_priv *priv, struct ipw2100_fw *fw) +{ + char *fw_name; + int rc; + + IPW_DEBUG_INFO("%s: Using hotplug firmware load.\n", + priv->net_dev->name); + + switch (priv->ieee->iw_mode) { + case IW_MODE_ADHOC: + fw_name = IPW2100_FW_NAME("-i"); + break; +#ifdef CONFIG_IPW2100_MONITOR + case IW_MODE_MONITOR: + fw_name = IPW2100_FW_NAME("-p"); + break; +#endif + case IW_MODE_INFRA: + default: + fw_name = IPW2100_FW_NAME(""); + break; + } + + rc = request_firmware(&fw->fw_entry, fw_name, &priv->pci_dev->dev); + + if (rc < 0) { + IPW_DEBUG_ERROR( + "%s: Firmware '%s' not available or load failed.\n", + priv->net_dev->name, fw_name); + return rc; + } + IPW_DEBUG_INFO("firmware data %p size %d\n", fw->fw_entry->data, + fw->fw_entry->size); + + ipw2100_mod_firmware_load(fw); + + return 0; +} + +void ipw2100_release_firmware(struct ipw2100_priv *priv, + struct ipw2100_fw *fw) +{ + fw->version = 0; + if (fw->fw_entry) + release_firmware(fw->fw_entry); + fw->fw_entry = NULL; +} + + +int ipw2100_get_fwversion(struct ipw2100_priv *priv, char *buf, size_t max) +{ + char ver[MAX_FW_VERSION_LEN]; + u32 len = MAX_FW_VERSION_LEN; + u32 tmp; + int i; + /* firmware version is an ascii string (max len of 14) */ + if (ipw2100_get_ordinal(priv, IPW_ORD_STAT_FW_VER_NUM, + ver, &len)) + return -EIO; + tmp = max; + if (len >= max) + len = max - 1; + for (i = 0; i < len; i++) + buf[i] = ver[i]; + buf[i] = '\0'; + return tmp; +} + +int ipw2100_get_ucodeversion(struct ipw2100_priv *priv, char *buf, size_t max) +{ + u32 ver; + u32 len = sizeof(ver); + /* microcode version is a 32 bit integer */ + if (ipw2100_get_ordinal(priv, IPW_ORD_UCODE_VERSION, + &ver, &len)) + return -EIO; + return snprintf(buf, max, "%08X", ver); +} + +/* + * On exit, the firmware will have been freed from the fw list + */ +int ipw2100_fw_download(struct ipw2100_priv *priv, struct ipw2100_fw *fw) +{ + /* firmware is constructed of N contiguous entries, each entry is + * structured as: + * + * offset sie desc + * 0 4 address to write to + * 4 2 length of data run + * 6 length data + */ + unsigned int addr; + unsigned short len; + + const unsigned char *firmware_data = fw->fw.data; + unsigned int firmware_data_left = fw->fw.size; + + while (firmware_data_left > 0) { + addr = *(u32 *)(firmware_data); + firmware_data += 4; + firmware_data_left -= 4; + + len = *(u16 *)(firmware_data); + firmware_data += 2; + firmware_data_left -= 2; + + if (len > 32) { + IPW_DEBUG_ERROR( + "Invalid firmware run-length of %d bytes\n", + len); + return -EINVAL; + } + + write_nic_memory(priv->net_dev, addr, len, firmware_data); + firmware_data += len; + firmware_data_left -= len; + } + + return 0; +} + +struct symbol_alive_response { + u8 cmd_id; + u8 seq_num; + u8 ucode_rev; + u8 eeprom_valid; + u16 valid_flags; + u8 IEEE_addr[6]; + u16 flags; + u16 pcb_rev; + u16 clock_settle_time; // 1us LSB + u16 powerup_settle_time; // 1us LSB + u16 hop_settle_time; // 1us LSB + u8 date[3]; // month, day, year + u8 time[2]; // hours, minutes + u8 ucode_valid; +}; + +int ipw2100_ucode_download(struct ipw2100_priv *priv, struct ipw2100_fw *fw) +{ + struct net_device *dev = priv->net_dev; + const unsigned char *microcode_data = fw->uc.data; + unsigned int microcode_data_left = fw->uc.size; + + struct symbol_alive_response response; + int i, j; + u8 data; + + /* Symbol control */ + write_nic_word(dev, IPW2100_CONTROL_REG, 0x703); + readl((void *)(dev->base_addr)); + write_nic_word(dev, IPW2100_CONTROL_REG, 0x707); + readl((void *)(dev->base_addr)); + + /* HW config */ + write_nic_byte(dev, 0x210014, 0x72); /* fifo width =16 */ + readl((void *)(dev->base_addr)); + write_nic_byte(dev, 0x210014, 0x72); /* fifo width =16 */ + readl((void *)(dev->base_addr)); + + /* EN_CS_ACCESS bit to reset control store pointer */ + write_nic_byte(dev, 0x210000, 0x40); + readl((void *)(dev->base_addr)); + write_nic_byte(dev, 0x210000, 0x0); + readl((void *)(dev->base_addr)); + write_nic_byte(dev, 0x210000, 0x40); + readl((void *)(dev->base_addr)); + + /* copy microcode from buffer into Symbol */ + + while (microcode_data_left > 0) { + write_nic_byte(dev, 0x210010, *microcode_data++); + write_nic_byte(dev, 0x210010, *microcode_data++); + microcode_data_left -= 2; + } + + /* EN_CS_ACCESS bit to reset the control store pointer */ + write_nic_byte(dev, 0x210000, 0x0); + readl((void *)(dev->base_addr)); + + /* Enable System (Reg 0) + * first enable causes garbage in RX FIFO */ + write_nic_byte(dev, 0x210000, 0x0); + readl((void *)(dev->base_addr)); + write_nic_byte(dev, 0x210000, 0x80); + readl((void *)(dev->base_addr)); + + /* Reset External Baseband Reg */ + write_nic_word(dev, IPW2100_CONTROL_REG, 0x703); + readl((void *)(dev->base_addr)); + write_nic_word(dev, IPW2100_CONTROL_REG, 0x707); + readl((void *)(dev->base_addr)); + + /* HW Config (Reg 5) */ + write_nic_byte(dev, 0x210014, 0x72); // fifo width =16 + readl((void *)(dev->base_addr)); + write_nic_byte(dev, 0x210014, 0x72); // fifo width =16 + readl((void *)(dev->base_addr)); + + /* Enable System (Reg 0) + * second enable should be OK */ + write_nic_byte(dev, 0x210000, 0x00); // clear enable system + readl((void *)(dev->base_addr)); + write_nic_byte(dev, 0x210000, 0x80); // set enable system + + /* check Symbol is enabled - upped this from 5 as it wasn't always + * catching the update */ + for (i = 0; i < 10; i++) { + udelay(10); + + /* check Dino is enabled bit */ + read_nic_byte(dev, 0x210000, &data); + if (data & 0x1) + break; + } + + if (i == 10) { + IPW_DEBUG_ERROR("%s: Error initializing Symbol\n", + dev->name); + return -EIO; + } + + /* Get Symbol alive response */ + for (i = 0; i < 30; i++) { + /* Read alive response structure */ + for (j = 0; + j < (sizeof(struct symbol_alive_response) >> 1); + j++) + read_nic_word(dev, 0x210004, + ((u16 *)&response) + j); + + if ((response.cmd_id == 1) && + (response.ucode_valid == 0x1)) + break; + udelay(10); + } + + if (i == 30) { + IPW_DEBUG_ERROR("%s: No response from Symbol - hw not alive\n", + dev->name); + printk_buf(IPW_DL_ERROR, (u8*)&response, sizeof(response)); + return -EIO; + } + + return 0; +} diff --git a/drivers/net/wireless/ipw2100.h b/drivers/net/wireless/ipw2100.h new file mode 100644 index 000000000000..0cc5746dd4f1 --- /dev/null +++ b/drivers/net/wireless/ipw2100.h @@ -0,0 +1,1278 @@ +/****************************************************************************** + + Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +******************************************************************************/ +#ifndef _IPW2100_H +#define _IPW2100_H + +#include <linux/sched.h> +#include <linux/interrupt.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/list.h> +#include <linux/delay.h> +#include <linux/skbuff.h> +#include <asm/io.h> +#include <linux/socket.h> +#include <linux/if_arp.h> +#include <linux/wireless.h> +#include <linux/version.h> +#include <net/iw_handler.h> // new driver API + +#include <net/ieee80211.h> + +#include <linux/workqueue.h> + +#ifndef IRQ_NONE +typedef void irqreturn_t; +#define IRQ_NONE +#define IRQ_HANDLED +#define IRQ_RETVAL(x) +#endif + +#if WIRELESS_EXT < 17 +#define IW_QUAL_QUAL_INVALID 0x10 +#define IW_QUAL_LEVEL_INVALID 0x20 +#define IW_QUAL_NOISE_INVALID 0x40 +#endif + +#if ( LINUX_VERSION_CODE < KERNEL_VERSION(2,6,5) ) +#define pci_dma_sync_single_for_cpu pci_dma_sync_single +#define pci_dma_sync_single_for_device pci_dma_sync_single +#endif + +#ifndef HAVE_FREE_NETDEV +#define free_netdev(x) kfree(x) +#endif + + + +struct ipw2100_priv; +struct ipw2100_tx_packet; +struct ipw2100_rx_packet; + +#ifdef CONFIG_IPW_DEBUG +enum { IPW_DEBUG_ENABLED = 1 }; +extern u32 ipw2100_debug_level; +#define IPW_DEBUG(level, message...) \ +do { \ + if (ipw2100_debug_level & (level)) { \ + printk(KERN_DEBUG "ipw2100: %c %s ", \ + in_interrupt() ? 'I' : 'U', __FUNCTION__); \ + printk(message); \ + } \ +} while (0) +#else +enum { IPW_DEBUG_ENABLED = 0 }; +#define IPW_DEBUG(level, message...) do {} while (0) +#endif /* CONFIG_IPW_DEBUG */ + +#define IPW_DL_UNINIT 0x80000000 +#define IPW_DL_NONE 0x00000000 +#define IPW_DL_ALL 0x7FFFFFFF + +/* + * To use the debug system; + * + * If you are defining a new debug classification, simply add it to the #define + * list here in the form of: + * + * #define IPW_DL_xxxx VALUE + * + * shifting value to the left one bit from the previous entry. xxxx should be + * the name of the classification (for example, WEP) + * + * You then need to either add a IPW2100_xxxx_DEBUG() macro definition for your + * classification, or use IPW_DEBUG(IPW_DL_xxxx, ...) whenever you want + * to send output to that classification. + * + * To add your debug level to the list of levels seen when you perform + * + * % cat /proc/net/ipw2100/debug_level + * + * you simply need to add your entry to the ipw2100_debug_levels array. + * + * If you do not see debug_level in /proc/net/ipw2100 then you do not have + * CONFIG_IPW_DEBUG defined in your kernel configuration + * + */ + +#define IPW_DL_ERROR (1<<0) +#define IPW_DL_WARNING (1<<1) +#define IPW_DL_INFO (1<<2) +#define IPW_DL_WX (1<<3) +#define IPW_DL_HC (1<<5) +#define IPW_DL_STATE (1<<6) + +#define IPW_DL_NOTIF (1<<10) +#define IPW_DL_SCAN (1<<11) +#define IPW_DL_ASSOC (1<<12) +#define IPW_DL_DROP (1<<13) + +#define IPW_DL_IOCTL (1<<14) +#define IPW_DL_RF_KILL (1<<17) + + +#define IPW_DL_MANAGE (1<<15) +#define IPW_DL_FW (1<<16) + +#define IPW_DL_FRAG (1<<21) +#define IPW_DL_WEP (1<<22) +#define IPW_DL_TX (1<<23) +#define IPW_DL_RX (1<<24) +#define IPW_DL_ISR (1<<25) +#define IPW_DL_IO (1<<26) +#define IPW_DL_TRACE (1<<28) + +#define IPW_DEBUG_ERROR(f, a...) printk(KERN_ERR DRV_NAME ": " f, ## a) +#define IPW_DEBUG_WARNING(f, a...) printk(KERN_WARNING DRV_NAME ": " f, ## a) +#define IPW_DEBUG_INFO(f...) IPW_DEBUG(IPW_DL_INFO, ## f) +#define IPW_DEBUG_WX(f...) IPW_DEBUG(IPW_DL_WX, ## f) +#define IPW_DEBUG_SCAN(f...) IPW_DEBUG(IPW_DL_SCAN, ## f) +#define IPW_DEBUG_NOTIF(f...) IPW_DEBUG(IPW_DL_NOTIF, ## f) +#define IPW_DEBUG_TRACE(f...) IPW_DEBUG(IPW_DL_TRACE, ## f) +#define IPW_DEBUG_RX(f...) IPW_DEBUG(IPW_DL_RX, ## f) +#define IPW_DEBUG_TX(f...) IPW_DEBUG(IPW_DL_TX, ## f) +#define IPW_DEBUG_ISR(f...) IPW_DEBUG(IPW_DL_ISR, ## f) +#define IPW_DEBUG_MANAGEMENT(f...) IPW_DEBUG(IPW_DL_MANAGE, ## f) +#define IPW_DEBUG_WEP(f...) IPW_DEBUG(IPW_DL_WEP, ## f) +#define IPW_DEBUG_HC(f...) IPW_DEBUG(IPW_DL_HC, ## f) +#define IPW_DEBUG_FRAG(f...) IPW_DEBUG(IPW_DL_FRAG, ## f) +#define IPW_DEBUG_FW(f...) IPW_DEBUG(IPW_DL_FW, ## f) +#define IPW_DEBUG_RF_KILL(f...) IPW_DEBUG(IPW_DL_RF_KILL, ## f) +#define IPW_DEBUG_DROP(f...) IPW_DEBUG(IPW_DL_DROP, ## f) +#define IPW_DEBUG_IO(f...) IPW_DEBUG(IPW_DL_IO, ## f) +#define IPW_DEBUG_IOCTL(f...) IPW_DEBUG(IPW_DL_IOCTL, ## f) +#define IPW_DEBUG_STATE(f, a...) IPW_DEBUG(IPW_DL_STATE | IPW_DL_ASSOC | IPW_DL_INFO, f, ## a) +#define IPW_DEBUG_ASSOC(f, a...) IPW_DEBUG(IPW_DL_ASSOC | IPW_DL_INFO, f, ## a) + + +#define VERIFY(f) \ +{ \ + int status = 0; \ + status = f; \ + if(status) \ + return status; \ +} + +enum { + IPW_HW_STATE_DISABLED = 1, + IPW_HW_STATE_ENABLED = 0 +}; + +struct ssid_context { + char ssid[IW_ESSID_MAX_SIZE + 1]; + int ssid_len; + unsigned char bssid[ETH_ALEN]; + int port_type; + int channel; + +}; + +extern const char *port_type_str[]; +extern const char *band_str[]; + +#define NUMBER_OF_BD_PER_COMMAND_PACKET 1 +#define NUMBER_OF_BD_PER_DATA_PACKET 2 + +#define IPW_MAX_BDS 6 +#define NUMBER_OF_OVERHEAD_BDS_PER_PACKETR 2 +#define NUMBER_OF_BDS_TO_LEAVE_FOR_COMMANDS 1 + +#define REQUIRED_SPACE_IN_RING_FOR_COMMAND_PACKET \ + (IPW_BD_QUEUE_W_R_MIN_SPARE + NUMBER_OF_BD_PER_COMMAND_PACKET) + +struct bd_status { + union { + struct { u8 nlf:1, txType:2, intEnabled:1, reserved:4;} fields; + u8 field; + } info; +} __attribute__ ((packed)); + +#define IPW_BUFDESC_LAST_FRAG 0 + +struct ipw2100_bd { + u32 host_addr; + u32 buf_length; + struct bd_status status; + /* number of fragments for frame (should be set only for + * 1st TBD) */ + u8 num_fragments; + u8 reserved[6]; +} __attribute__ ((packed)); + +#define IPW_BD_QUEUE_LENGTH(n) (1<<n) +#define IPW_BD_ALIGNMENT(L) (L*sizeof(struct ipw2100_bd)) + +#define IPW_BD_STATUS_TX_FRAME_802_3 0x00 +#define IPW_BD_STATUS_TX_FRAME_NOT_LAST_FRAGMENT 0x01 +#define IPW_BD_STATUS_TX_FRAME_COMMAND 0x02 +#define IPW_BD_STATUS_TX_FRAME_802_11 0x04 +#define IPW_BD_STATUS_TX_INTERRUPT_ENABLE 0x08 + +struct ipw2100_bd_queue { + /* driver (virtual) pointer to queue */ + struct ipw2100_bd *drv; + + /* firmware (physical) pointer to queue */ + dma_addr_t nic; + + /* Length of phy memory allocated for BDs */ + u32 size; + + /* Number of BDs in queue (and in array) */ + u32 entries; + + /* Number of available BDs (invalid for NIC BDs) */ + u32 available; + + /* Offset of oldest used BD in array (next one to + * check for completion) */ + u32 oldest; + + /* Offset of next available (unused) BD */ + u32 next; +}; + +#define RX_QUEUE_LENGTH 256 +#define TX_QUEUE_LENGTH 256 +#define HW_QUEUE_LENGTH 256 + +#define TX_PENDED_QUEUE_LENGTH (TX_QUEUE_LENGTH / NUMBER_OF_BD_PER_DATA_PACKET) + +#define STATUS_TYPE_MASK 0x0000000f +#define COMMAND_STATUS_VAL 0 +#define STATUS_CHANGE_VAL 1 +#define P80211_DATA_VAL 2 +#define P8023_DATA_VAL 3 +#define HOST_NOTIFICATION_VAL 4 + +#define IPW2100_RSSI_TO_DBM (-98) + +struct ipw2100_status { + u32 frame_size; + u16 status_fields; + u8 flags; +#define IPW_STATUS_FLAG_DECRYPTED (1<<0) +#define IPW_STATUS_FLAG_WEP_ENCRYPTED (1<<1) +#define IPW_STATUS_FLAG_CRC_ERROR (1<<2) + u8 rssi; +} __attribute__ ((packed)); + +struct ipw2100_status_queue { + /* driver (virtual) pointer to queue */ + struct ipw2100_status *drv; + + /* firmware (physical) pointer to queue */ + dma_addr_t nic; + + /* Length of phy memory allocated for BDs */ + u32 size; +}; + +#define HOST_COMMAND_PARAMS_REG_LEN 100 +#define CMD_STATUS_PARAMS_REG_LEN 3 + +#define IPW_WPA_CAPABILITIES 0x1 +#define IPW_WPA_LISTENINTERVAL 0x2 +#define IPW_WPA_AP_ADDRESS 0x4 + +#define IPW_MAX_VAR_IE_LEN ((HOST_COMMAND_PARAMS_REG_LEN - 4) * sizeof(u32)) + +struct ipw2100_wpa_assoc_frame { + u16 fixed_ie_mask; + struct { + u16 capab_info; + u16 listen_interval; + u8 current_ap[ETH_ALEN]; + } fixed_ies; + u32 var_ie_len; + u8 var_ie[IPW_MAX_VAR_IE_LEN]; +}; + +#define IPW_BSS 1 +#define IPW_MONITOR 2 +#define IPW_IBSS 3 + +/** + * @struct _tx_cmd - HWCommand + * @brief H/W command structure. + */ +struct ipw2100_cmd_header { + u32 host_command_reg; + u32 host_command_reg1; + u32 sequence; + u32 host_command_len_reg; + u32 host_command_params_reg[HOST_COMMAND_PARAMS_REG_LEN]; + u32 cmd_status_reg; + u32 cmd_status_params_reg[CMD_STATUS_PARAMS_REG_LEN]; + u32 rxq_base_ptr; + u32 rxq_next_ptr; + u32 rxq_host_ptr; + u32 txq_base_ptr; + u32 txq_next_ptr; + u32 txq_host_ptr; + u32 tx_status_reg; + u32 reserved; + u32 status_change_reg; + u32 reserved1[3]; + u32 *ordinal1_ptr; + u32 *ordinal2_ptr; +} __attribute__ ((packed)); + +struct ipw2100_data_header { + u32 host_command_reg; + u32 host_command_reg1; + u8 encrypted; // BOOLEAN in win! TRUE if frame is enc by driver + u8 needs_encryption; // BOOLEAN in win! TRUE if frma need to be enc in NIC + u8 wep_index; // 0 no key, 1-4 key index, 0xff immediate key + u8 key_size; // 0 no imm key, 0x5 64bit encr, 0xd 128bit encr, 0x10 128bit encr and 128bit IV + u8 key[16]; + u8 reserved[10]; // f/w reserved + u8 src_addr[ETH_ALEN]; + u8 dst_addr[ETH_ALEN]; + u16 fragment_size; +} __attribute__ ((packed)); + +// Host command data structure +struct host_command { + u32 host_command; // COMMAND ID + u32 host_command1; // COMMAND ID + u32 host_command_sequence; // UNIQUE COMMAND NUMBER (ID) + u32 host_command_length; // LENGTH + u32 host_command_parameters[HOST_COMMAND_PARAMS_REG_LEN]; // COMMAND PARAMETERS +} __attribute__ ((packed)); + + +typedef enum { + POWER_ON_RESET, + EXIT_POWER_DOWN_RESET, + SW_RESET, + EEPROM_RW, + SW_RE_INIT +} ipw2100_reset_event; + +enum { + COMMAND = 0xCAFE, + DATA, + RX +}; + + +struct ipw2100_tx_packet { + int type; + int index; + union { + struct { /* COMMAND */ + struct ipw2100_cmd_header* cmd; + dma_addr_t cmd_phys; + } c_struct; + struct { /* DATA */ + struct ipw2100_data_header* data; + dma_addr_t data_phys; + struct ieee80211_txb *txb; + } d_struct; + } info; + int jiffy_start; + + struct list_head list; +}; + + +struct ipw2100_rx_packet { + struct ipw2100_rx *rxp; + dma_addr_t dma_addr; + int jiffy_start; + struct sk_buff *skb; + struct list_head list; +}; + +#define FRAG_DISABLED (1<<31) +#define RTS_DISABLED (1<<31) +#define MAX_RTS_THRESHOLD 2304U +#define MIN_RTS_THRESHOLD 1U +#define DEFAULT_RTS_THRESHOLD 1000U + +#define DEFAULT_BEACON_INTERVAL 100U +#define DEFAULT_SHORT_RETRY_LIMIT 7U +#define DEFAULT_LONG_RETRY_LIMIT 4U + +struct ipw2100_ordinals { + u32 table1_addr; + u32 table2_addr; + u32 table1_size; + u32 table2_size; +}; + +/* Host Notification header */ +struct ipw2100_notification { + u32 hnhdr_subtype; /* type of host notification */ + u32 hnhdr_size; /* size in bytes of data + or number of entries, if table. + Does NOT include header */ +} __attribute__ ((packed)); + +#define MAX_KEY_SIZE 16 +#define MAX_KEYS 8 + +#define IPW2100_WEP_ENABLE (1<<1) +#define IPW2100_WEP_DROP_CLEAR (1<<2) + +#define IPW_NONE_CIPHER (1<<0) +#define IPW_WEP40_CIPHER (1<<1) +#define IPW_TKIP_CIPHER (1<<2) +#define IPW_CCMP_CIPHER (1<<4) +#define IPW_WEP104_CIPHER (1<<5) +#define IPW_CKIP_CIPHER (1<<6) + +#define IPW_AUTH_OPEN 0 +#define IPW_AUTH_SHARED 1 + +struct statistic { + int value; + int hi; + int lo; +}; + +#define INIT_STAT(x) do { \ + (x)->value = (x)->hi = 0; \ + (x)->lo = 0x7fffffff; \ +} while (0) +#define SET_STAT(x,y) do { \ + (x)->value = y; \ + if ((x)->value > (x)->hi) (x)->hi = (x)->value; \ + if ((x)->value < (x)->lo) (x)->lo = (x)->value; \ +} while (0) +#define INC_STAT(x) do { if (++(x)->value > (x)->hi) (x)->hi = (x)->value; } \ +while (0) +#define DEC_STAT(x) do { if (--(x)->value < (x)->lo) (x)->lo = (x)->value; } \ +while (0) + +#define IPW2100_ERROR_QUEUE 5 + +/* Power management code: enable or disable? */ +enum { +#ifdef CONFIG_PM + IPW2100_PM_DISABLED = 0, + PM_STATE_SIZE = 16, +#else + IPW2100_PM_DISABLED = 1, + PM_STATE_SIZE = 0, +#endif +}; + +#define STATUS_POWERED (1<<0) +#define STATUS_CMD_ACTIVE (1<<1) /**< host command in progress */ +#define STATUS_RUNNING (1<<2) /* Card initialized, but not enabled */ +#define STATUS_ENABLED (1<<3) /* Card enabled -- can scan,Tx,Rx */ +#define STATUS_STOPPING (1<<4) /* Card is in shutdown phase */ +#define STATUS_INITIALIZED (1<<5) /* Card is ready for external calls */ +#define STATUS_ASSOCIATING (1<<9) /* Associated, but no BSSID yet */ +#define STATUS_ASSOCIATED (1<<10) /* Associated and BSSID valid */ +#define STATUS_INT_ENABLED (1<<11) +#define STATUS_RF_KILL_HW (1<<12) +#define STATUS_RF_KILL_SW (1<<13) +#define STATUS_RF_KILL_MASK (STATUS_RF_KILL_HW | STATUS_RF_KILL_SW) +#define STATUS_EXIT_PENDING (1<<14) + +#define STATUS_SCAN_PENDING (1<<23) +#define STATUS_SCANNING (1<<24) +#define STATUS_SCAN_ABORTING (1<<25) +#define STATUS_SCAN_COMPLETE (1<<26) +#define STATUS_WX_EVENT_PENDING (1<<27) +#define STATUS_RESET_PENDING (1<<29) +#define STATUS_SECURITY_UPDATED (1<<30) /* Security sync needed */ + + + +/* Internal NIC states */ +#define IPW_STATE_INITIALIZED (1<<0) +#define IPW_STATE_COUNTRY_FOUND (1<<1) +#define IPW_STATE_ASSOCIATED (1<<2) +#define IPW_STATE_ASSN_LOST (1<<3) +#define IPW_STATE_ASSN_CHANGED (1<<4) +#define IPW_STATE_SCAN_COMPLETE (1<<5) +#define IPW_STATE_ENTERED_PSP (1<<6) +#define IPW_STATE_LEFT_PSP (1<<7) +#define IPW_STATE_RF_KILL (1<<8) +#define IPW_STATE_DISABLED (1<<9) +#define IPW_STATE_POWER_DOWN (1<<10) +#define IPW_STATE_SCANNING (1<<11) + + + +#define CFG_STATIC_CHANNEL (1<<0) /* Restrict assoc. to single channel */ +#define CFG_STATIC_ESSID (1<<1) /* Restrict assoc. to single SSID */ +#define CFG_STATIC_BSSID (1<<2) /* Restrict assoc. to single BSSID */ +#define CFG_CUSTOM_MAC (1<<3) +#define CFG_LONG_PREAMBLE (1<<4) +#define CFG_ASSOCIATE (1<<6) +#define CFG_FIXED_RATE (1<<7) +#define CFG_ADHOC_CREATE (1<<8) +#define CFG_C3_DISABLED (1<<9) +#define CFG_PASSIVE_SCAN (1<<10) + +#define CAP_SHARED_KEY (1<<0) /* Off = OPEN */ +#define CAP_PRIVACY_ON (1<<1) /* Off = No privacy */ + +struct ipw2100_priv { + + int stop_hang_check; /* Set 1 when shutting down to kill hang_check */ + int stop_rf_kill; /* Set 1 when shutting down to kill rf_kill */ + + struct ieee80211_device *ieee; + unsigned long status; + unsigned long config; + unsigned long capability; + + /* Statistics */ + int resets; + int reset_backoff; + + /* Context */ + u8 essid[IW_ESSID_MAX_SIZE]; + u8 essid_len; + u8 bssid[ETH_ALEN]; + u8 channel; + int last_mode; + int cstate_limit; + + unsigned long connect_start; + unsigned long last_reset; + + u32 channel_mask; + u32 fatal_error; + u32 fatal_errors[IPW2100_ERROR_QUEUE]; + u32 fatal_index; + int eeprom_version; + int firmware_version; + unsigned long hw_features; + int hangs; + u32 last_rtc; + int dump_raw; /* 1 to dump raw bytes in /sys/.../memory */ + u8* snapshot[0x30]; + + u8 mandatory_bssid_mac[ETH_ALEN]; + u8 mac_addr[ETH_ALEN]; + + int power_mode; + + /* WEP data */ + struct ieee80211_security sec; + int messages_sent; + + + int short_retry_limit; + int long_retry_limit; + + u32 rts_threshold; + u32 frag_threshold; + + int in_isr; + + u32 tx_rates; + int tx_power; + u32 beacon_interval; + + char nick[IW_ESSID_MAX_SIZE + 1]; + + struct ipw2100_status_queue status_queue; + + struct statistic txq_stat; + struct statistic rxq_stat; + struct ipw2100_bd_queue rx_queue; + struct ipw2100_bd_queue tx_queue; + struct ipw2100_rx_packet *rx_buffers; + + struct statistic fw_pend_stat; + struct list_head fw_pend_list; + + struct statistic msg_free_stat; + struct statistic msg_pend_stat; + struct list_head msg_free_list; + struct list_head msg_pend_list; + struct ipw2100_tx_packet *msg_buffers; + + struct statistic tx_free_stat; + struct statistic tx_pend_stat; + struct list_head tx_free_list; + struct list_head tx_pend_list; + struct ipw2100_tx_packet *tx_buffers; + + struct ipw2100_ordinals ordinals; + + struct pci_dev *pci_dev; + + struct proc_dir_entry *dir_dev; + + struct net_device *net_dev; + struct iw_statistics wstats; + + struct tasklet_struct irq_tasklet; + + struct workqueue_struct *workqueue; + struct work_struct reset_work; + struct work_struct security_work; + struct work_struct wx_event_work; + struct work_struct hang_check; + struct work_struct rf_kill; + + u32 interrupts; + int tx_interrupts; + int rx_interrupts; + int inta_other; + + spinlock_t low_lock; + struct semaphore action_sem; + struct semaphore adapter_sem; + + wait_queue_head_t wait_command_queue; +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,10) + u32 pm_state[PM_STATE_SIZE]; +#endif +}; + + +/********************************************************* + * Host Command -> From Driver to FW + *********************************************************/ + +/** + * Host command identifiers + */ +#define HOST_COMPLETE 2 +#define SYSTEM_CONFIG 6 +#define SSID 8 +#define MANDATORY_BSSID 9 +#define AUTHENTICATION_TYPE 10 +#define ADAPTER_ADDRESS 11 +#define PORT_TYPE 12 +#define INTERNATIONAL_MODE 13 +#define CHANNEL 14 +#define RTS_THRESHOLD 15 +#define FRAG_THRESHOLD 16 +#define POWER_MODE 17 +#define TX_RATES 18 +#define BASIC_TX_RATES 19 +#define WEP_KEY_INFO 20 +#define WEP_KEY_INDEX 25 +#define WEP_FLAGS 26 +#define ADD_MULTICAST 27 +#define CLEAR_ALL_MULTICAST 28 +#define BEACON_INTERVAL 29 +#define ATIM_WINDOW 30 +#define CLEAR_STATISTICS 31 +#define SEND 33 +#define TX_POWER_INDEX 36 +#define BROADCAST_SCAN 43 +#define CARD_DISABLE 44 +#define PREFERRED_BSSID 45 +#define SET_SCAN_OPTIONS 46 +#define SCAN_DWELL_TIME 47 +#define SWEEP_TABLE 48 +#define AP_OR_STATION_TABLE 49 +#define GROUP_ORDINALS 50 +#define SHORT_RETRY_LIMIT 51 +#define LONG_RETRY_LIMIT 52 + +#define HOST_PRE_POWER_DOWN 58 +#define CARD_DISABLE_PHY_OFF 61 +#define MSDU_TX_RATES 62 + + +// Rogue AP Detection +#define SET_STATION_STAT_BITS 64 +#define CLEAR_STATIONS_STAT_BITS 65 +#define LEAP_ROGUE_MODE 66 //TODO tbw replaced by CFG_LEAP_ROGUE_AP +#define SET_SECURITY_INFORMATION 67 +#define DISASSOCIATION_BSSID 68 +#define SET_WPA_IE 69 + + + +// system configuration bit mask: +//#define IPW_CFG_ANTENNA_SETTING 0x03 +//#define IPW_CFG_ANTENNA_A 0x01 +//#define IPW_CFG_ANTENNA_B 0x02 +#define IPW_CFG_MONITOR 0x00004 +//#define IPW_CFG_TX_STATUS_ENABLE 0x00008 +#define IPW_CFG_PREAMBLE_AUTO 0x00010 +#define IPW_CFG_IBSS_AUTO_START 0x00020 +//#define IPW_CFG_KERBEROS_ENABLE 0x00040 +#define IPW_CFG_LOOPBACK 0x00100 +//#define IPW_CFG_WNMP_PING_PASS 0x00200 +//#define IPW_CFG_DEBUG_ENABLE 0x00400 +#define IPW_CFG_ANSWER_BCSSID_PROBE 0x00800 +//#define IPW_CFG_BT_PRIORITY 0x01000 +#define IPW_CFG_BT_SIDEBAND_SIGNAL 0x02000 +#define IPW_CFG_802_1x_ENABLE 0x04000 +#define IPW_CFG_BSS_MASK 0x08000 +#define IPW_CFG_IBSS_MASK 0x10000 +//#define IPW_CFG_DYNAMIC_CW 0x10000 + +#define IPW_SCAN_NOASSOCIATE (1<<0) +#define IPW_SCAN_MIXED_CELL (1<<1) +/* RESERVED (1<<2) */ +#define IPW_SCAN_PASSIVE (1<<3) + +#define IPW_NIC_FATAL_ERROR 0x2A7F0 +#define IPW_ERROR_ADDR(x) (x & 0x3FFFF) +#define IPW_ERROR_CODE(x) ((x & 0xFF000000) >> 24) +#define IPW2100_ERR_C3_CORRUPTION (0x10 << 24) +#define IPW2100_ERR_MSG_TIMEOUT (0x11 << 24) +#define IPW2100_ERR_FW_LOAD (0x12 << 24) + +#define IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND 0x200 +#define IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x0D80 + +#define IPW_MEM_HOST_SHARED_RX_BD_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x40) +#define IPW_MEM_HOST_SHARED_RX_STATUS_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x44) +#define IPW_MEM_HOST_SHARED_RX_BD_SIZE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x48) +#define IPW_MEM_HOST_SHARED_RX_READ_INDEX (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0xa0) + +#define IPW_MEM_HOST_SHARED_TX_QUEUE_BD_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x00) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_BD_SIZE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x04) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_READ_INDEX (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x80) + +#define IPW_MEM_HOST_SHARED_RX_WRITE_INDEX \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND + 0x20) + +#define IPW_MEM_HOST_SHARED_TX_QUEUE_WRITE_INDEX \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND) + + +#if 0 +#define IPW_MEM_HOST_SHARED_TX_QUEUE_0_BD_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x00) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_0_BD_SIZE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x04) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_1_BD_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x08) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_1_BD_SIZE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x0c) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_2_BD_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x10) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_2_BD_SIZE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x14) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_3_BD_BASE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x18) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_3_BD_SIZE (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x1c) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_0_READ_INDEX (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x80) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_1_READ_INDEX (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x84) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_2_READ_INDEX (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x88) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_3_READ_INDEX (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x8c) + +#define IPW_MEM_HOST_SHARED_TX_QUEUE_BD_BASE(QueueNum) \ + (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + (QueueNum<<3)) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_BD_SIZE(QueueNum) \ + (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x0004+(QueueNum<<3)) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_READ_INDEX(QueueNum) \ + (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x0080+(QueueNum<<2)) + +#define IPW_MEM_HOST_SHARED_TX_QUEUE_0_WRITE_INDEX \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND + 0x00) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_1_WRITE_INDEX \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND + 0x04) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_2_WRITE_INDEX \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND + 0x08) +#define IPW_MEM_HOST_SHARED_TX_QUEUE_3_WRITE_INDEX \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND + 0x0c) +#define IPW_MEM_HOST_SHARED_SLAVE_MODE_INT_REGISTER \ + (IPW_MEM_SRAM_HOST_INTERRUPT_AREA_LOWER_BOUND + 0x78) + +#endif + +#define IPW_MEM_HOST_SHARED_ORDINALS_TABLE_1 (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x180) +#define IPW_MEM_HOST_SHARED_ORDINALS_TABLE_2 (IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + 0x184) + +#define IPW2100_INTA_TX_TRANSFER (0x00000001) // Bit 0 (LSB) +#define IPW2100_INTA_RX_TRANSFER (0x00000002) // Bit 1 +#define IPW2100_INTA_TX_COMPLETE (0x00000004) // Bit 2 +#define IPW2100_INTA_EVENT_INTERRUPT (0x00000008) // Bit 3 +#define IPW2100_INTA_STATUS_CHANGE (0x00000010) // Bit 4 +#define IPW2100_INTA_BEACON_PERIOD_EXPIRED (0x00000020) // Bit 5 +#define IPW2100_INTA_SLAVE_MODE_HOST_COMMAND_DONE (0x00010000) // Bit 16 +#define IPW2100_INTA_FW_INIT_DONE (0x01000000) // Bit 24 +#define IPW2100_INTA_FW_CALIBRATION_CALC (0x02000000) // Bit 25 +#define IPW2100_INTA_FATAL_ERROR (0x40000000) // Bit 30 +#define IPW2100_INTA_PARITY_ERROR (0x80000000) // Bit 31 (MSB) + +#define IPW_AUX_HOST_RESET_REG_PRINCETON_RESET (0x00000001) +#define IPW_AUX_HOST_RESET_REG_FORCE_NMI (0x00000002) +#define IPW_AUX_HOST_RESET_REG_PCI_HOST_CLUSTER_FATAL_NMI (0x00000004) +#define IPW_AUX_HOST_RESET_REG_CORE_FATAL_NMI (0x00000008) +#define IPW_AUX_HOST_RESET_REG_SW_RESET (0x00000080) +#define IPW_AUX_HOST_RESET_REG_MASTER_DISABLED (0x00000100) +#define IPW_AUX_HOST_RESET_REG_STOP_MASTER (0x00000200) + +#define IPW_AUX_HOST_GP_CNTRL_BIT_CLOCK_READY (0x00000001) // Bit 0 (LSB) +#define IPW_AUX_HOST_GP_CNTRL_BIT_HOST_ALLOWS_STANDBY (0x00000002) // Bit 1 +#define IPW_AUX_HOST_GP_CNTRL_BIT_INIT_DONE (0x00000004) // Bit 2 +#define IPW_AUX_HOST_GP_CNTRL_BITS_SYS_CONFIG (0x000007c0) // Bits 6-10 +#define IPW_AUX_HOST_GP_CNTRL_BIT_BUS_TYPE (0x00000200) // Bit 9 +#define IPW_AUX_HOST_GP_CNTRL_BIT_BAR0_BLOCK_SIZE (0x00000400) // Bit 10 +#define IPW_AUX_HOST_GP_CNTRL_BIT_USB_MODE (0x20000000) // Bit 29 +#define IPW_AUX_HOST_GP_CNTRL_BIT_HOST_FORCES_SYS_CLK (0x40000000) // Bit 30 +#define IPW_AUX_HOST_GP_CNTRL_BIT_FW_FORCES_SYS_CLK (0x80000000) // Bit 31 (MSB) + +#define IPW_BIT_GPIO_GPIO1_MASK 0x0000000C +#define IPW_BIT_GPIO_GPIO3_MASK 0x000000C0 +#define IPW_BIT_GPIO_GPIO1_ENABLE 0x00000008 +#define IPW_BIT_GPIO_RF_KILL 0x00010000 + +#define IPW_BIT_GPIO_LED_OFF 0x00002000 // Bit 13 = 1 + +#define IPW_REG_DOMAIN_0_OFFSET 0x0000 +#define IPW_REG_DOMAIN_1_OFFSET IPW_MEM_SRAM_HOST_SHARED_LOWER_BOUND + +#define IPW_REG_INTA IPW_REG_DOMAIN_0_OFFSET + 0x0008 +#define IPW_REG_INTA_MASK IPW_REG_DOMAIN_0_OFFSET + 0x000C +#define IPW_REG_INDIRECT_ACCESS_ADDRESS IPW_REG_DOMAIN_0_OFFSET + 0x0010 +#define IPW_REG_INDIRECT_ACCESS_DATA IPW_REG_DOMAIN_0_OFFSET + 0x0014 +#define IPW_REG_AUTOINCREMENT_ADDRESS IPW_REG_DOMAIN_0_OFFSET + 0x0018 +#define IPW_REG_AUTOINCREMENT_DATA IPW_REG_DOMAIN_0_OFFSET + 0x001C +#define IPW_REG_RESET_REG IPW_REG_DOMAIN_0_OFFSET + 0x0020 +#define IPW_REG_GP_CNTRL IPW_REG_DOMAIN_0_OFFSET + 0x0024 +#define IPW_REG_GPIO IPW_REG_DOMAIN_0_OFFSET + 0x0030 +#define IPW_REG_FW_TYPE IPW_REG_DOMAIN_1_OFFSET + 0x0188 +#define IPW_REG_FW_VERSION IPW_REG_DOMAIN_1_OFFSET + 0x018C +#define IPW_REG_FW_COMPATABILITY_VERSION IPW_REG_DOMAIN_1_OFFSET + 0x0190 + +#define IPW_REG_INDIRECT_ADDR_MASK 0x00FFFFFC + +#define IPW_INTERRUPT_MASK 0xC1010013 + +#define IPW2100_CONTROL_REG 0x220000 +#define IPW2100_CONTROL_PHY_OFF 0x8 + +#define IPW2100_COMMAND 0x00300004 +#define IPW2100_COMMAND_PHY_ON 0x0 +#define IPW2100_COMMAND_PHY_OFF 0x1 + +/* in DEBUG_AREA, values of memory always 0xd55555d5 */ +#define IPW_REG_DOA_DEBUG_AREA_START IPW_REG_DOMAIN_0_OFFSET + 0x0090 +#define IPW_REG_DOA_DEBUG_AREA_END IPW_REG_DOMAIN_0_OFFSET + 0x00FF +#define IPW_DATA_DOA_DEBUG_VALUE 0xd55555d5 + +#define IPW_INTERNAL_REGISTER_HALT_AND_RESET 0x003000e0 + +#define IPW_WAIT_CLOCK_STABILIZATION_DELAY 50 // micro seconds +#define IPW_WAIT_RESET_ARC_COMPLETE_DELAY 10 // micro seconds +#define IPW_WAIT_RESET_MASTER_ASSERT_COMPLETE_DELAY 10 // micro seconds + +// BD ring queue read/write difference +#define IPW_BD_QUEUE_W_R_MIN_SPARE 2 + +#define IPW_CACHE_LINE_LENGTH_DEFAULT 0x80 + +#define IPW_CARD_DISABLE_PHY_OFF_COMPLETE_WAIT 100 // 100 milli +#define IPW_PREPARE_POWER_DOWN_COMPLETE_WAIT 100 // 100 milli + + + + +#define IPW_HEADER_802_11_SIZE sizeof(struct ieee80211_header_data) +#define IPW_MAX_80211_PAYLOAD_SIZE 2304U +#define IPW_MAX_802_11_PAYLOAD_LENGTH 2312 +#define IPW_MAX_ACCEPTABLE_TX_FRAME_LENGTH 1536 +#define IPW_MIN_ACCEPTABLE_RX_FRAME_LENGTH 60 +#define IPW_MAX_ACCEPTABLE_RX_FRAME_LENGTH \ + (IPW_MAX_ACCEPTABLE_TX_FRAME_LENGTH + IPW_HEADER_802_11_SIZE - \ + sizeof(struct ethhdr)) + +#define IPW_802_11_FCS_LENGTH 4 +#define IPW_RX_NIC_BUFFER_LENGTH \ + (IPW_MAX_802_11_PAYLOAD_LENGTH + IPW_HEADER_802_11_SIZE + \ + IPW_802_11_FCS_LENGTH) + +#define IPW_802_11_PAYLOAD_OFFSET \ + (sizeof(struct ieee80211_header_data) + \ + sizeof(struct ieee80211_snap_hdr)) + +struct ipw2100_rx { + union { + unsigned char payload[IPW_RX_NIC_BUFFER_LENGTH]; + struct ieee80211_hdr header; + u32 status; + struct ipw2100_notification notification; + struct ipw2100_cmd_header command; + } rx_data; +} __attribute__ ((packed)); + +// Bit 0-7 are for 802.11b tx rates - . Bit 5-7 are reserved +#define TX_RATE_1_MBIT 0x0001 +#define TX_RATE_2_MBIT 0x0002 +#define TX_RATE_5_5_MBIT 0x0004 +#define TX_RATE_11_MBIT 0x0008 +#define TX_RATE_MASK 0x000F +#define DEFAULT_TX_RATES 0x000F + +#define IPW_POWER_MODE_CAM 0x00 //(always on) +#define IPW_POWER_INDEX_1 0x01 +#define IPW_POWER_INDEX_2 0x02 +#define IPW_POWER_INDEX_3 0x03 +#define IPW_POWER_INDEX_4 0x04 +#define IPW_POWER_INDEX_5 0x05 +#define IPW_POWER_AUTO 0x06 +#define IPW_POWER_MASK 0x0F +#define IPW_POWER_ENABLED 0x10 +#define IPW_POWER_LEVEL(x) ((x) & IPW_POWER_MASK) + +#define IPW_TX_POWER_AUTO 0 +#define IPW_TX_POWER_ENHANCED 1 + +#define IPW_TX_POWER_DEFAULT 32 +#define IPW_TX_POWER_MIN 0 +#define IPW_TX_POWER_MAX 16 +#define IPW_TX_POWER_MIN_DBM (-12) +#define IPW_TX_POWER_MAX_DBM 16 + +#define FW_SCAN_DONOT_ASSOCIATE 0x0001 // Dont Attempt to Associate after Scan +#define FW_SCAN_PASSIVE 0x0008 // Force PASSSIVE Scan + +#define REG_MIN_CHANNEL 0 +#define REG_MAX_CHANNEL 14 + +#define REG_CHANNEL_MASK 0x00003FFF +#define IPW_IBSS_11B_DEFAULT_MASK 0x87ff + +#define DIVERSITY_EITHER 0 // Use both antennas +#define DIVERSITY_ANTENNA_A 1 // Use antenna A +#define DIVERSITY_ANTENNA_B 2 // Use antenna B + + +#define HOST_COMMAND_WAIT 0 +#define HOST_COMMAND_NO_WAIT 1 + +#define LOCK_NONE 0 +#define LOCK_DRIVER 1 +#define LOCK_FW 2 + +#define TYPE_SWEEP_ORD 0x000D +#define TYPE_IBSS_STTN_ORD 0x000E +#define TYPE_BSS_AP_ORD 0x000F +#define TYPE_RAW_BEACON_ENTRY 0x0010 +#define TYPE_CALIBRATION_DATA 0x0011 +#define TYPE_ROGUE_AP_DATA 0x0012 +#define TYPE_ASSOCIATION_REQUEST 0x0013 +#define TYPE_REASSOCIATION_REQUEST 0x0014 + + +#define HW_FEATURE_RFKILL (0x0001) +#define RF_KILLSWITCH_OFF (1) +#define RF_KILLSWITCH_ON (0) + +#define IPW_COMMAND_POOL_SIZE 40 + +#define IPW_START_ORD_TAB_1 1 +#define IPW_START_ORD_TAB_2 1000 + +#define IPW_ORD_TAB_1_ENTRY_SIZE sizeof(u32) + +#define IS_ORDINAL_TABLE_ONE(mgr,id) \ + ((id >= IPW_START_ORD_TAB_1) && (id < mgr->table1_size)) +#define IS_ORDINAL_TABLE_TWO(mgr,id) \ + ((id >= IPW_START_ORD_TAB_2) && (id < (mgr->table2_size + IPW_START_ORD_TAB_2))) + +#define BSS_ID_LENGTH 6 + +// Fixed size data: Ordinal Table 1 +typedef enum _ORDINAL_TABLE_1 { // NS - means Not Supported by FW +// Transmit statistics + IPW_ORD_STAT_TX_HOST_REQUESTS = 1,// # of requested Host Tx's (MSDU) + IPW_ORD_STAT_TX_HOST_COMPLETE, // # of successful Host Tx's (MSDU) + IPW_ORD_STAT_TX_DIR_DATA, // # of successful Directed Tx's (MSDU) + + IPW_ORD_STAT_TX_DIR_DATA1 = 4, // # of successful Directed Tx's (MSDU) @ 1MB + IPW_ORD_STAT_TX_DIR_DATA2, // # of successful Directed Tx's (MSDU) @ 2MB + IPW_ORD_STAT_TX_DIR_DATA5_5, // # of successful Directed Tx's (MSDU) @ 5_5MB + IPW_ORD_STAT_TX_DIR_DATA11, // # of successful Directed Tx's (MSDU) @ 11MB + IPW_ORD_STAT_TX_DIR_DATA22, // # of successful Directed Tx's (MSDU) @ 22MB + + IPW_ORD_STAT_TX_NODIR_DATA1 = 13,// # of successful Non_Directed Tx's (MSDU) @ 1MB + IPW_ORD_STAT_TX_NODIR_DATA2, // # of successful Non_Directed Tx's (MSDU) @ 2MB + IPW_ORD_STAT_TX_NODIR_DATA5_5, // # of successful Non_Directed Tx's (MSDU) @ 5.5MB + IPW_ORD_STAT_TX_NODIR_DATA11, // # of successful Non_Directed Tx's (MSDU) @ 11MB + + IPW_ORD_STAT_NULL_DATA = 21, // # of successful NULL data Tx's + IPW_ORD_STAT_TX_RTS, // # of successful Tx RTS + IPW_ORD_STAT_TX_CTS, // # of successful Tx CTS + IPW_ORD_STAT_TX_ACK, // # of successful Tx ACK + IPW_ORD_STAT_TX_ASSN, // # of successful Association Tx's + IPW_ORD_STAT_TX_ASSN_RESP, // # of successful Association response Tx's + IPW_ORD_STAT_TX_REASSN, // # of successful Reassociation Tx's + IPW_ORD_STAT_TX_REASSN_RESP, // # of successful Reassociation response Tx's + IPW_ORD_STAT_TX_PROBE, // # of probes successfully transmitted + IPW_ORD_STAT_TX_PROBE_RESP, // # of probe responses successfully transmitted + IPW_ORD_STAT_TX_BEACON, // # of tx beacon + IPW_ORD_STAT_TX_ATIM, // # of Tx ATIM + IPW_ORD_STAT_TX_DISASSN, // # of successful Disassociation TX + IPW_ORD_STAT_TX_AUTH, // # of successful Authentication Tx + IPW_ORD_STAT_TX_DEAUTH, // # of successful Deauthentication TX + + IPW_ORD_STAT_TX_TOTAL_BYTES = 41,// Total successful Tx data bytes + IPW_ORD_STAT_TX_RETRIES, // # of Tx retries + IPW_ORD_STAT_TX_RETRY1, // # of Tx retries at 1MBPS + IPW_ORD_STAT_TX_RETRY2, // # of Tx retries at 2MBPS + IPW_ORD_STAT_TX_RETRY5_5, // # of Tx retries at 5.5MBPS + IPW_ORD_STAT_TX_RETRY11, // # of Tx retries at 11MBPS + + IPW_ORD_STAT_TX_FAILURES = 51, // # of Tx Failures + IPW_ORD_STAT_TX_ABORT_AT_HOP, //NS // # of Tx's aborted at hop time + IPW_ORD_STAT_TX_MAX_TRIES_IN_HOP,// # of times max tries in a hop failed + IPW_ORD_STAT_TX_ABORT_LATE_DMA, //NS // # of times tx aborted due to late dma setup + IPW_ORD_STAT_TX_ABORT_STX, //NS // # of times backoff aborted + IPW_ORD_STAT_TX_DISASSN_FAIL, // # of times disassociation failed + IPW_ORD_STAT_TX_ERR_CTS, // # of missed/bad CTS frames + IPW_ORD_STAT_TX_BPDU, //NS // # of spanning tree BPDUs sent + IPW_ORD_STAT_TX_ERR_ACK, // # of tx err due to acks + + // Receive statistics + IPW_ORD_STAT_RX_HOST = 61, // # of packets passed to host + IPW_ORD_STAT_RX_DIR_DATA, // # of directed packets + IPW_ORD_STAT_RX_DIR_DATA1, // # of directed packets at 1MB + IPW_ORD_STAT_RX_DIR_DATA2, // # of directed packets at 2MB + IPW_ORD_STAT_RX_DIR_DATA5_5, // # of directed packets at 5.5MB + IPW_ORD_STAT_RX_DIR_DATA11, // # of directed packets at 11MB + IPW_ORD_STAT_RX_DIR_DATA22, // # of directed packets at 22MB + + IPW_ORD_STAT_RX_NODIR_DATA = 71,// # of nondirected packets + IPW_ORD_STAT_RX_NODIR_DATA1, // # of nondirected packets at 1MB + IPW_ORD_STAT_RX_NODIR_DATA2, // # of nondirected packets at 2MB + IPW_ORD_STAT_RX_NODIR_DATA5_5, // # of nondirected packets at 5.5MB + IPW_ORD_STAT_RX_NODIR_DATA11, // # of nondirected packets at 11MB + + IPW_ORD_STAT_RX_NULL_DATA = 80, // # of null data rx's + IPW_ORD_STAT_RX_POLL, //NS // # of poll rx + IPW_ORD_STAT_RX_RTS, // # of Rx RTS + IPW_ORD_STAT_RX_CTS, // # of Rx CTS + IPW_ORD_STAT_RX_ACK, // # of Rx ACK + IPW_ORD_STAT_RX_CFEND, // # of Rx CF End + IPW_ORD_STAT_RX_CFEND_ACK, // # of Rx CF End + CF Ack + IPW_ORD_STAT_RX_ASSN, // # of Association Rx's + IPW_ORD_STAT_RX_ASSN_RESP, // # of Association response Rx's + IPW_ORD_STAT_RX_REASSN, // # of Reassociation Rx's + IPW_ORD_STAT_RX_REASSN_RESP, // # of Reassociation response Rx's + IPW_ORD_STAT_RX_PROBE, // # of probe Rx's + IPW_ORD_STAT_RX_PROBE_RESP, // # of probe response Rx's + IPW_ORD_STAT_RX_BEACON, // # of Rx beacon + IPW_ORD_STAT_RX_ATIM, // # of Rx ATIM + IPW_ORD_STAT_RX_DISASSN, // # of disassociation Rx + IPW_ORD_STAT_RX_AUTH, // # of authentication Rx + IPW_ORD_STAT_RX_DEAUTH, // # of deauthentication Rx + + IPW_ORD_STAT_RX_TOTAL_BYTES = 101,// Total rx data bytes received + IPW_ORD_STAT_RX_ERR_CRC, // # of packets with Rx CRC error + IPW_ORD_STAT_RX_ERR_CRC1, // # of Rx CRC errors at 1MB + IPW_ORD_STAT_RX_ERR_CRC2, // # of Rx CRC errors at 2MB + IPW_ORD_STAT_RX_ERR_CRC5_5, // # of Rx CRC errors at 5.5MB + IPW_ORD_STAT_RX_ERR_CRC11, // # of Rx CRC errors at 11MB + + IPW_ORD_STAT_RX_DUPLICATE1 = 112, // # of duplicate rx packets at 1MB + IPW_ORD_STAT_RX_DUPLICATE2, // # of duplicate rx packets at 2MB + IPW_ORD_STAT_RX_DUPLICATE5_5, // # of duplicate rx packets at 5.5MB + IPW_ORD_STAT_RX_DUPLICATE11, // # of duplicate rx packets at 11MB + IPW_ORD_STAT_RX_DUPLICATE = 119, // # of duplicate rx packets + + IPW_ORD_PERS_DB_LOCK = 120, // # locking fw permanent db + IPW_ORD_PERS_DB_SIZE, // # size of fw permanent db + IPW_ORD_PERS_DB_ADDR, // # address of fw permanent db + IPW_ORD_STAT_RX_INVALID_PROTOCOL, // # of rx frames with invalid protocol + IPW_ORD_SYS_BOOT_TIME, // # Boot time + IPW_ORD_STAT_RX_NO_BUFFER, // # of rx frames rejected due to no buffer + IPW_ORD_STAT_RX_ABORT_LATE_DMA, //NS // # of rx frames rejected due to dma setup too late + IPW_ORD_STAT_RX_ABORT_AT_HOP, //NS // # of rx frames aborted due to hop + IPW_ORD_STAT_RX_MISSING_FRAG, // # of rx frames dropped due to missing fragment + IPW_ORD_STAT_RX_ORPHAN_FRAG, // # of rx frames dropped due to non-sequential fragment + IPW_ORD_STAT_RX_ORPHAN_FRAME, // # of rx frames dropped due to unmatched 1st frame + IPW_ORD_STAT_RX_FRAG_AGEOUT, // # of rx frames dropped due to uncompleted frame + IPW_ORD_STAT_RX_BAD_SSID, //NS // Bad SSID (unused) + IPW_ORD_STAT_RX_ICV_ERRORS, // # of ICV errors during decryption + +// PSP Statistics + IPW_ORD_STAT_PSP_SUSPENSION = 137,// # of times adapter suspended + IPW_ORD_STAT_PSP_BCN_TIMEOUT, // # of beacon timeout + IPW_ORD_STAT_PSP_POLL_TIMEOUT, // # of poll response timeouts + IPW_ORD_STAT_PSP_NONDIR_TIMEOUT,// # of timeouts waiting for last broadcast/muticast pkt + IPW_ORD_STAT_PSP_RX_DTIMS, // # of PSP DTIMs received + IPW_ORD_STAT_PSP_RX_TIMS, // # of PSP TIMs received + IPW_ORD_STAT_PSP_STATION_ID, // PSP Station ID + +// Association and roaming + IPW_ORD_LAST_ASSN_TIME = 147, // RTC time of last association + IPW_ORD_STAT_PERCENT_MISSED_BCNS,// current calculation of % missed beacons + IPW_ORD_STAT_PERCENT_RETRIES, // current calculation of % missed tx retries + IPW_ORD_ASSOCIATED_AP_PTR, // If associated, this is ptr to the associated + // AP table entry. set to 0 if not associated + IPW_ORD_AVAILABLE_AP_CNT, // # of AP's decsribed in the AP table + IPW_ORD_AP_LIST_PTR, // Ptr to list of available APs + IPW_ORD_STAT_AP_ASSNS, // # of associations + IPW_ORD_STAT_ASSN_FAIL, // # of association failures + IPW_ORD_STAT_ASSN_RESP_FAIL, // # of failuresdue to response fail + IPW_ORD_STAT_FULL_SCANS, // # of full scans + + IPW_ORD_CARD_DISABLED, // # Card Disabled + IPW_ORD_STAT_ROAM_INHIBIT, // # of times roaming was inhibited due to ongoing activity + IPW_FILLER_40, + IPW_ORD_RSSI_AT_ASSN = 160, // RSSI of associated AP at time of association + IPW_ORD_STAT_ASSN_CAUSE1, // # of reassociations due to no tx from AP in last N + // hops or no prob_ responses in last 3 minutes + IPW_ORD_STAT_ASSN_CAUSE2, // # of reassociations due to poor tx/rx quality + IPW_ORD_STAT_ASSN_CAUSE3, // # of reassociations due to tx/rx quality with excessive + // load at the AP + IPW_ORD_STAT_ASSN_CAUSE4, // # of reassociations due to AP RSSI level fell below + // eligible group + IPW_ORD_STAT_ASSN_CAUSE5, // # of reassociations due to load leveling + IPW_ORD_STAT_ASSN_CAUSE6, //NS // # of reassociations due to dropped by Ap + IPW_FILLER_41, + IPW_FILLER_42, + IPW_FILLER_43, + IPW_ORD_STAT_AUTH_FAIL, // # of times authentication failed + IPW_ORD_STAT_AUTH_RESP_FAIL, // # of times authentication response failed + IPW_ORD_STATION_TABLE_CNT, // # of entries in association table + +// Other statistics + IPW_ORD_RSSI_AVG_CURR = 173, // Current avg RSSI + IPW_ORD_STEST_RESULTS_CURR, //NS // Current self test results word + IPW_ORD_STEST_RESULTS_CUM, //NS // Cummulative self test results word + IPW_ORD_SELF_TEST_STATUS, //NS // + IPW_ORD_POWER_MGMT_MODE, // Power mode - 0=CAM, 1=PSP + IPW_ORD_POWER_MGMT_INDEX, //NS // + IPW_ORD_COUNTRY_CODE, // IEEE country code as recv'd from beacon + IPW_ORD_COUNTRY_CHANNELS, // channels suported by country +// IPW_ORD_COUNTRY_CHANNELS: +// For 11b the lower 2-byte are used for channels from 1-14 +// and the higher 2-byte are not used. + IPW_ORD_RESET_CNT, // # of adapter resets (warm) + IPW_ORD_BEACON_INTERVAL, // Beacon interval + + IPW_ORD_PRINCETON_VERSION = 184, //NS // Princeton Version + IPW_ORD_ANTENNA_DIVERSITY, // TRUE if antenna diversity is disabled + IPW_ORD_CCA_RSSI, //NS // CCA RSSI value (factory programmed) + IPW_ORD_STAT_EEPROM_UPDATE, //NS // # of times config EEPROM updated + IPW_ORD_DTIM_PERIOD, // # of beacon intervals between DTIMs + IPW_ORD_OUR_FREQ, // current radio freq lower digits - channel ID + + IPW_ORD_RTC_TIME = 190, // current RTC time + IPW_ORD_PORT_TYPE, // operating mode + IPW_ORD_CURRENT_TX_RATE, // current tx rate + IPW_ORD_SUPPORTED_RATES, // Bitmap of supported tx rates + IPW_ORD_ATIM_WINDOW, // current ATIM Window + IPW_ORD_BASIC_RATES, // bitmap of basic tx rates + IPW_ORD_NIC_HIGHEST_RATE, // bitmap of basic tx rates + IPW_ORD_AP_HIGHEST_RATE, // bitmap of basic tx rates + IPW_ORD_CAPABILITIES, // Management frame capability field + IPW_ORD_AUTH_TYPE, // Type of authentication + IPW_ORD_RADIO_TYPE, // Adapter card platform type + IPW_ORD_RTS_THRESHOLD = 201, // Min length of packet after which RTS handshaking is used + IPW_ORD_INT_MODE, // International mode + IPW_ORD_FRAGMENTATION_THRESHOLD, // protocol frag threshold + IPW_ORD_EEPROM_SRAM_DB_BLOCK_START_ADDRESS, // EEPROM offset in SRAM + IPW_ORD_EEPROM_SRAM_DB_BLOCK_SIZE, // EEPROM size in SRAM + IPW_ORD_EEPROM_SKU_CAPABILITY, // EEPROM SKU Capability 206 = + IPW_ORD_EEPROM_IBSS_11B_CHANNELS, // EEPROM IBSS 11b channel set + + IPW_ORD_MAC_VERSION = 209, // MAC Version + IPW_ORD_MAC_REVISION, // MAC Revision + IPW_ORD_RADIO_VERSION, // Radio Version + IPW_ORD_NIC_MANF_DATE_TIME, // MANF Date/Time STAMP + IPW_ORD_UCODE_VERSION, // Ucode Version + IPW_ORD_HW_RF_SWITCH_STATE = 214, // HW RF Kill Switch State +} ORDINALTABLE1; +//ENDOF TABLE1 + +// ordinal table 2 +// Variable length data: +#define IPW_FIRST_VARIABLE_LENGTH_ORDINAL 1001 + +typedef enum _ORDINAL_TABLE_2 { // NS - means Not Supported by FW + IPW_ORD_STAT_BASE = 1000, // contains number of variable ORDs + IPW_ORD_STAT_ADAPTER_MAC = 1001, // 6 bytes: our adapter MAC address + IPW_ORD_STAT_PREFERRED_BSSID = 1002, // 6 bytes: BSSID of the preferred AP + IPW_ORD_STAT_MANDATORY_BSSID = 1003, // 6 bytes: BSSID of the mandatory AP + IPW_FILL_1, //NS // + IPW_ORD_STAT_COUNTRY_TEXT = 1005, // 36 bytes: Country name text, First two bytes are Country code + IPW_ORD_STAT_ASSN_SSID = 1006, // 32 bytes: ESSID String + IPW_ORD_STATION_TABLE = 1007, // ? bytes: Station/AP table (via Direct SSID Scans) + IPW_ORD_STAT_SWEEP_TABLE = 1008, // ? bytes: Sweep/Host Table table (via Broadcast Scans) + IPW_ORD_STAT_ROAM_LOG = 1009, // ? bytes: Roaming log + IPW_ORD_STAT_RATE_LOG = 1010, //NS // 0 bytes: Rate log + IPW_ORD_STAT_FIFO = 1011, //NS // 0 bytes: Fifo buffer data structures + IPW_ORD_STAT_FW_VER_NUM = 1012, // 14 bytes: fw version ID string as in (a.bb.ccc; "0.08.011") + IPW_ORD_STAT_FW_DATE = 1013, // 14 bytes: fw date string (mmm dd yyyy; "Mar 13 2002") + IPW_ORD_STAT_ASSN_AP_BSSID = 1014, // 6 bytes: MAC address of associated AP + IPW_ORD_STAT_DEBUG = 1015, //NS // ? bytes: + IPW_ORD_STAT_NIC_BPA_NUM = 1016, // 11 bytes: NIC BPA number in ASCII + IPW_ORD_STAT_UCODE_DATE = 1017, // 5 bytes: uCode date + IPW_ORD_SECURITY_NGOTIATION_RESULT = 1018, +} ORDINALTABLE2; // NS - means Not Supported by FW + +#define IPW_LAST_VARIABLE_LENGTH_ORDINAL 1018 + +#ifndef WIRELESS_SPY +#define WIRELESS_SPY // enable iwspy support +#endif + +extern struct iw_handler_def ipw2100_wx_handler_def; +extern struct iw_statistics *ipw2100_wx_wireless_stats(struct net_device * dev); +extern void ipw2100_wx_event_work(struct ipw2100_priv *priv); + +#define IPW_HOST_FW_SHARED_AREA0 0x0002f200 +#define IPW_HOST_FW_SHARED_AREA0_END 0x0002f510 // 0x310 bytes + +#define IPW_HOST_FW_SHARED_AREA1 0x0002f610 +#define IPW_HOST_FW_SHARED_AREA1_END 0x0002f630 // 0x20 bytes + +#define IPW_HOST_FW_SHARED_AREA2 0x0002fa00 +#define IPW_HOST_FW_SHARED_AREA2_END 0x0002fa20 // 0x20 bytes + +#define IPW_HOST_FW_SHARED_AREA3 0x0002fc00 +#define IPW_HOST_FW_SHARED_AREA3_END 0x0002fc10 // 0x10 bytes + +#define IPW_HOST_FW_INTERRUPT_AREA 0x0002ff80 +#define IPW_HOST_FW_INTERRUPT_AREA_END 0x00030000 // 0x80 bytes + +struct ipw2100_fw_chunk { + unsigned char *buf; + long len; + long pos; + struct list_head list; +}; + +struct ipw2100_fw_chunk_set { + const void *data; + unsigned long size; +}; + +struct ipw2100_fw { + int version; + struct ipw2100_fw_chunk_set fw; + struct ipw2100_fw_chunk_set uc; + const struct firmware *fw_entry; +}; + +int ipw2100_get_firmware(struct ipw2100_priv *priv, struct ipw2100_fw *fw); +void ipw2100_release_firmware(struct ipw2100_priv *priv, struct ipw2100_fw *fw); +int ipw2100_fw_download(struct ipw2100_priv *priv, struct ipw2100_fw *fw); +int ipw2100_ucode_download(struct ipw2100_priv *priv, struct ipw2100_fw *fw); + +#define MAX_FW_VERSION_LEN 14 + +int ipw2100_get_fwversion(struct ipw2100_priv *priv, char *buf, size_t max); +int ipw2100_get_ucodeversion(struct ipw2100_priv *priv, char *buf, size_t max); + +#endif /* _IPW2100_H */ diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c new file mode 100644 index 000000000000..69733465354b --- /dev/null +++ b/drivers/net/wireless/ipw2200.c @@ -0,0 +1,7348 @@ +/****************************************************************************** + + Copyright(c) 2003 - 2004 Intel Corporation. All rights reserved. + + 802.11 status code portion of this file from ethereal-0.10.6: + Copyright 2000, Axis Communications AB + Ethereal - Network traffic analyzer + By Gerald Combs <gerald@ethereal.com> + Copyright 1998 Gerald Combs + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +******************************************************************************/ + +#include "ipw2200.h" + +#define IPW2200_VERSION "1.0.0" +#define DRV_DESCRIPTION "Intel(R) PRO/Wireless 2200/2915 Network Driver" +#define DRV_COPYRIGHT "Copyright(c) 2003-2004 Intel Corporation" +#define DRV_VERSION IPW2200_VERSION + +MODULE_DESCRIPTION(DRV_DESCRIPTION); +MODULE_VERSION(DRV_VERSION); +MODULE_AUTHOR(DRV_COPYRIGHT); +MODULE_LICENSE("GPL"); + +static int debug = 0; +static int channel = 0; +static char *ifname; +static int mode = 0; + +static u32 ipw_debug_level; +static int associate = 1; +static int auto_create = 1; +static int disable = 0; +static const char ipw_modes[] = { + 'a', 'b', 'g', '?' +}; + +static void ipw_rx(struct ipw_priv *priv); +static int ipw_queue_tx_reclaim(struct ipw_priv *priv, + struct clx2_tx_queue *txq, int qindex); +static int ipw_queue_reset(struct ipw_priv *priv); + +static int ipw_queue_tx_hcmd(struct ipw_priv *priv, int hcmd, void *buf, + int len, int sync); + +static void ipw_tx_queue_free(struct ipw_priv *); + +static struct ipw_rx_queue *ipw_rx_queue_alloc(struct ipw_priv *); +static void ipw_rx_queue_free(struct ipw_priv *, struct ipw_rx_queue *); +static void ipw_rx_queue_replenish(void *); + +static int ipw_up(struct ipw_priv *); +static void ipw_down(struct ipw_priv *); +static int ipw_config(struct ipw_priv *); +static int init_supported_rates(struct ipw_priv *priv, struct ipw_supported_rates *prates); + +static u8 band_b_active_channel[MAX_B_CHANNELS] = { + 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 0 +}; +static u8 band_a_active_channel[MAX_A_CHANNELS] = { + 36, 40, 44, 48, 149, 153, 157, 161, 165, 52, 56, 60, 64, 0 +}; + +static int is_valid_channel(int mode_mask, int channel) +{ + int i; + + if (!channel) + return 0; + + if (mode_mask & IEEE_A) + for (i = 0; i < MAX_A_CHANNELS; i++) + if (band_a_active_channel[i] == channel) + return IEEE_A; + + if (mode_mask & (IEEE_B | IEEE_G)) + for (i = 0; i < MAX_B_CHANNELS; i++) + if (band_b_active_channel[i] == channel) + return mode_mask & (IEEE_B | IEEE_G); + + return 0; +} + +static char *snprint_line(char *buf, size_t count, + const u8 *data, u32 len, u32 ofs) +{ + int out, i, j, l; + char c; + + out = snprintf(buf, count, "%08X", ofs); + + for (l = 0, i = 0; i < 2; i++) { + out += snprintf(buf + out, count - out, " "); + for (j = 0; j < 8 && l < len; j++, l++) + out += snprintf(buf + out, count - out, "%02X ", + data[(i * 8 + j)]); + for (; j < 8; j++) + out += snprintf(buf + out, count - out, " "); + } + + out += snprintf(buf + out, count - out, " "); + for (l = 0, i = 0; i < 2; i++) { + out += snprintf(buf + out, count - out, " "); + for (j = 0; j < 8 && l < len; j++, l++) { + c = data[(i * 8 + j)]; + if (!isascii(c) || !isprint(c)) + c = '.'; + + out += snprintf(buf + out, count - out, "%c", c); + } + + for (; j < 8; j++) + out += snprintf(buf + out, count - out, " "); + } + + return buf; +} + +static void printk_buf(int level, const u8 *data, u32 len) +{ + char line[81]; + u32 ofs = 0; + if (!(ipw_debug_level & level)) + return; + + while (len) { + printk(KERN_DEBUG "%s\n", + snprint_line(line, sizeof(line), &data[ofs], + min(len, 16U), ofs)); + ofs += 16; + len -= min(len, 16U); + } +} + +static u32 _ipw_read_reg32(struct ipw_priv *priv, u32 reg); +#define ipw_read_reg32(a, b) _ipw_read_reg32(a, b) + +static u8 _ipw_read_reg8(struct ipw_priv *ipw, u32 reg); +#define ipw_read_reg8(a, b) _ipw_read_reg8(a, b) + +static void _ipw_write_reg8(struct ipw_priv *priv, u32 reg, u8 value); +static inline void ipw_write_reg8(struct ipw_priv *a, u32 b, u8 c) +{ + IPW_DEBUG_IO("%s %d: write_indirect8(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(b), (u32)(c)); + _ipw_write_reg8(a, b, c); +} + +static void _ipw_write_reg16(struct ipw_priv *priv, u32 reg, u16 value); +static inline void ipw_write_reg16(struct ipw_priv *a, u32 b, u16 c) +{ + IPW_DEBUG_IO("%s %d: write_indirect16(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(b), (u32)(c)); + _ipw_write_reg16(a, b, c); +} + +static void _ipw_write_reg32(struct ipw_priv *priv, u32 reg, u32 value); +static inline void ipw_write_reg32(struct ipw_priv *a, u32 b, u32 c) +{ + IPW_DEBUG_IO("%s %d: write_indirect32(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(b), (u32)(c)); + _ipw_write_reg32(a, b, c); +} + +#define _ipw_write8(ipw, ofs, val) writeb((val), (ipw)->hw_base + (ofs)) +#define ipw_write8(ipw, ofs, val) \ + IPW_DEBUG_IO("%s %d: write_direct8(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(ofs), (u32)(val)); \ + _ipw_write8(ipw, ofs, val) + +#define _ipw_write16(ipw, ofs, val) writew((val), (ipw)->hw_base + (ofs)) +#define ipw_write16(ipw, ofs, val) \ + IPW_DEBUG_IO("%s %d: write_direct16(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(ofs), (u32)(val)); \ + _ipw_write16(ipw, ofs, val) + +#define _ipw_write32(ipw, ofs, val) writel((val), (ipw)->hw_base + (ofs)) +#define ipw_write32(ipw, ofs, val) \ + IPW_DEBUG_IO("%s %d: write_direct32(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(ofs), (u32)(val)); \ + _ipw_write32(ipw, ofs, val) + +#define _ipw_read8(ipw, ofs) readb((ipw)->hw_base + (ofs)) +static inline u8 __ipw_read8(char *f, u32 l, struct ipw_priv *ipw, u32 ofs) { + IPW_DEBUG_IO("%s %d: read_direct8(0x%08X)\n", f, l, (u32)(ofs)); + return _ipw_read8(ipw, ofs); +} +#define ipw_read8(ipw, ofs) __ipw_read8(__FILE__, __LINE__, ipw, ofs) + +#define _ipw_read16(ipw, ofs) readw((ipw)->hw_base + (ofs)) +static inline u16 __ipw_read16(char *f, u32 l, struct ipw_priv *ipw, u32 ofs) { + IPW_DEBUG_IO("%s %d: read_direct16(0x%08X)\n", f, l, (u32)(ofs)); + return _ipw_read16(ipw, ofs); +} +#define ipw_read16(ipw, ofs) __ipw_read16(__FILE__, __LINE__, ipw, ofs) + +#define _ipw_read32(ipw, ofs) readl((ipw)->hw_base + (ofs)) +static inline u32 __ipw_read32(char *f, u32 l, struct ipw_priv *ipw, u32 ofs) { + IPW_DEBUG_IO("%s %d: read_direct32(0x%08X)\n", f, l, (u32)(ofs)); + return _ipw_read32(ipw, ofs); +} +#define ipw_read32(ipw, ofs) __ipw_read32(__FILE__, __LINE__, ipw, ofs) + +static void _ipw_read_indirect(struct ipw_priv *, u32, u8 *, int); +#define ipw_read_indirect(a, b, c, d) \ + IPW_DEBUG_IO("%s %d: read_inddirect(0x%08X) %d bytes\n", __FILE__, __LINE__, (u32)(b), d); \ + _ipw_read_indirect(a, b, c, d) + +static void _ipw_write_indirect(struct ipw_priv *priv, u32 addr, u8 *data, int num); +#define ipw_write_indirect(a, b, c, d) \ + IPW_DEBUG_IO("%s %d: write_indirect(0x%08X) %d bytes\n", __FILE__, __LINE__, (u32)(b), d); \ + _ipw_write_indirect(a, b, c, d) + +/* indirect write s */ +static void _ipw_write_reg32(struct ipw_priv *priv, u32 reg, + u32 value) +{ + IPW_DEBUG_IO(" %p : reg = 0x%8X : value = 0x%8X\n", + priv, reg, value); + _ipw_write32(priv, CX2_INDIRECT_ADDR, reg); + _ipw_write32(priv, CX2_INDIRECT_DATA, value); +} + + +static void _ipw_write_reg8(struct ipw_priv *priv, u32 reg, u8 value) +{ + IPW_DEBUG_IO(" reg = 0x%8X : value = 0x%8X\n", reg, value); + _ipw_write32(priv, CX2_INDIRECT_ADDR, reg & CX2_INDIRECT_ADDR_MASK); + _ipw_write8(priv, CX2_INDIRECT_DATA, value); + IPW_DEBUG_IO(" reg = 0x%8X : value = 0x%8X\n", + (unsigned)(priv->hw_base + CX2_INDIRECT_DATA), + value); +} + +static void _ipw_write_reg16(struct ipw_priv *priv, u32 reg, + u16 value) +{ + IPW_DEBUG_IO(" reg = 0x%8X : value = 0x%8X\n", reg, value); + _ipw_write32(priv, CX2_INDIRECT_ADDR, reg & CX2_INDIRECT_ADDR_MASK); + _ipw_write16(priv, CX2_INDIRECT_DATA, value); +} + +/* indirect read s */ + +static u8 _ipw_read_reg8(struct ipw_priv *priv, u32 reg) +{ + u32 word; + _ipw_write32(priv, CX2_INDIRECT_ADDR, reg & CX2_INDIRECT_ADDR_MASK); + IPW_DEBUG_IO(" reg = 0x%8X : \n", reg); + word = _ipw_read32(priv, CX2_INDIRECT_DATA); + return (word >> ((reg & 0x3)*8)) & 0xff; +} + +static u32 _ipw_read_reg32(struct ipw_priv *priv, u32 reg) +{ + u32 value; + + IPW_DEBUG_IO("%p : reg = 0x%08x\n", priv, reg); + + _ipw_write32(priv, CX2_INDIRECT_ADDR, reg); + value = _ipw_read32(priv, CX2_INDIRECT_DATA); + IPW_DEBUG_IO(" reg = 0x%4X : value = 0x%4x \n", reg, value); + return value; +} + +/* iterative/auto-increment 32 bit reads and writes */ +static void _ipw_read_indirect(struct ipw_priv *priv, u32 addr, u8 * buf, + int num) +{ + u32 aligned_addr = addr & CX2_INDIRECT_ADDR_MASK; + u32 dif_len = addr - aligned_addr; + u32 aligned_len; + u32 i; + + IPW_DEBUG_IO("addr = %i, buf = %p, num = %i\n", addr, buf, num); + + /* Read the first nibble byte by byte */ + if (unlikely(dif_len)) { + /* Start reading at aligned_addr + dif_len */ + _ipw_write32(priv, CX2_INDIRECT_ADDR, aligned_addr); + for (i = dif_len; i < 4; i++, buf++) + *buf = _ipw_read8(priv, CX2_INDIRECT_DATA + i); + num -= dif_len; + aligned_addr += 4; + } + + /* Read DWs through autoinc register */ + _ipw_write32(priv, CX2_AUTOINC_ADDR, aligned_addr); + aligned_len = num & CX2_INDIRECT_ADDR_MASK; + for (i = 0; i < aligned_len; i += 4, buf += 4, aligned_addr += 4) + *(u32*)buf = ipw_read32(priv, CX2_AUTOINC_DATA); + + /* Copy the last nibble */ + dif_len = num - aligned_len; + _ipw_write32(priv, CX2_INDIRECT_ADDR, aligned_addr); + for (i = 0; i < dif_len; i++, buf++) + *buf = ipw_read8(priv, CX2_INDIRECT_DATA + i); +} + +static void _ipw_write_indirect(struct ipw_priv *priv, u32 addr, u8 *buf, + int num) +{ + u32 aligned_addr = addr & CX2_INDIRECT_ADDR_MASK; + u32 dif_len = addr - aligned_addr; + u32 aligned_len; + u32 i; + + IPW_DEBUG_IO("addr = %i, buf = %p, num = %i\n", addr, buf, num); + + /* Write the first nibble byte by byte */ + if (unlikely(dif_len)) { + /* Start writing at aligned_addr + dif_len */ + _ipw_write32(priv, CX2_INDIRECT_ADDR, aligned_addr); + for (i = dif_len; i < 4; i++, buf++) + _ipw_write8(priv, CX2_INDIRECT_DATA + i, *buf); + num -= dif_len; + aligned_addr += 4; + } + + /* Write DWs through autoinc register */ + _ipw_write32(priv, CX2_AUTOINC_ADDR, aligned_addr); + aligned_len = num & CX2_INDIRECT_ADDR_MASK; + for (i = 0; i < aligned_len; i += 4, buf += 4, aligned_addr += 4) + _ipw_write32(priv, CX2_AUTOINC_DATA, *(u32*)buf); + + /* Copy the last nibble */ + dif_len = num - aligned_len; + _ipw_write32(priv, CX2_INDIRECT_ADDR, aligned_addr); + for (i = 0; i < dif_len; i++, buf++) + _ipw_write8(priv, CX2_INDIRECT_DATA + i, *buf); +} + +static void ipw_write_direct(struct ipw_priv *priv, u32 addr, void *buf, + int num) +{ + memcpy_toio((priv->hw_base + addr), buf, num); +} + +static inline void ipw_set_bit(struct ipw_priv *priv, u32 reg, u32 mask) +{ + ipw_write32(priv, reg, ipw_read32(priv, reg) | mask); +} + +static inline void ipw_clear_bit(struct ipw_priv *priv, u32 reg, u32 mask) +{ + ipw_write32(priv, reg, ipw_read32(priv, reg) & ~mask); +} + +static inline void ipw_enable_interrupts(struct ipw_priv *priv) +{ + if (priv->status & STATUS_INT_ENABLED) + return; + priv->status |= STATUS_INT_ENABLED; + ipw_write32(priv, CX2_INTA_MASK_R, CX2_INTA_MASK_ALL); +} + +static inline void ipw_disable_interrupts(struct ipw_priv *priv) +{ + if (!(priv->status & STATUS_INT_ENABLED)) + return; + priv->status &= ~STATUS_INT_ENABLED; + ipw_write32(priv, CX2_INTA_MASK_R, ~CX2_INTA_MASK_ALL); +} + +static char *ipw_error_desc(u32 val) +{ + switch (val) { + case IPW_FW_ERROR_OK: + return "ERROR_OK"; + case IPW_FW_ERROR_FAIL: + return "ERROR_FAIL"; + case IPW_FW_ERROR_MEMORY_UNDERFLOW: + return "MEMORY_UNDERFLOW"; + case IPW_FW_ERROR_MEMORY_OVERFLOW: + return "MEMORY_OVERFLOW"; + case IPW_FW_ERROR_BAD_PARAM: + return "ERROR_BAD_PARAM"; + case IPW_FW_ERROR_BAD_CHECKSUM: + return "ERROR_BAD_CHECKSUM"; + case IPW_FW_ERROR_NMI_INTERRUPT: + return "ERROR_NMI_INTERRUPT"; + case IPW_FW_ERROR_BAD_DATABASE: + return "ERROR_BAD_DATABASE"; + case IPW_FW_ERROR_ALLOC_FAIL: + return "ERROR_ALLOC_FAIL"; + case IPW_FW_ERROR_DMA_UNDERRUN: + return "ERROR_DMA_UNDERRUN"; + case IPW_FW_ERROR_DMA_STATUS: + return "ERROR_DMA_STATUS"; + case IPW_FW_ERROR_DINOSTATUS_ERROR: + return "ERROR_DINOSTATUS_ERROR"; + case IPW_FW_ERROR_EEPROMSTATUS_ERROR: + return "ERROR_EEPROMSTATUS_ERROR"; + case IPW_FW_ERROR_SYSASSERT: + return "ERROR_SYSASSERT"; + case IPW_FW_ERROR_FATAL_ERROR: + return "ERROR_FATALSTATUS_ERROR"; + default: + return "UNKNOWNSTATUS_ERROR"; + } +} + +static void ipw_dump_nic_error_log(struct ipw_priv *priv) +{ + u32 desc, time, blink1, blink2, ilink1, ilink2, idata, i, count, base; + + base = ipw_read32(priv, IPWSTATUS_ERROR_LOG); + count = ipw_read_reg32(priv, base); + + if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) { + IPW_ERROR("Start IPW Error Log Dump:\n"); + IPW_ERROR("Status: 0x%08X, Config: %08X\n", + priv->status, priv->config); + } + + for (i = ERROR_START_OFFSET; + i <= count * ERROR_ELEM_SIZE; + i += ERROR_ELEM_SIZE) { + desc = ipw_read_reg32(priv, base + i); + time = ipw_read_reg32(priv, base + i + 1*sizeof(u32)); + blink1 = ipw_read_reg32(priv, base + i + 2*sizeof(u32)); + blink2 = ipw_read_reg32(priv, base + i + 3*sizeof(u32)); + ilink1 = ipw_read_reg32(priv, base + i + 4*sizeof(u32)); + ilink2 = ipw_read_reg32(priv, base + i + 5*sizeof(u32)); + idata = ipw_read_reg32(priv, base + i + 6*sizeof(u32)); + + IPW_ERROR( + "%s %i 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x\n", + ipw_error_desc(desc), time, blink1, blink2, + ilink1, ilink2, idata); + } +} + +static void ipw_dump_nic_event_log(struct ipw_priv *priv) +{ + u32 ev, time, data, i, count, base; + + base = ipw_read32(priv, IPW_EVENT_LOG); + count = ipw_read_reg32(priv, base); + + if (EVENT_START_OFFSET <= count * EVENT_ELEM_SIZE) + IPW_ERROR("Start IPW Event Log Dump:\n"); + + for (i = EVENT_START_OFFSET; + i <= count * EVENT_ELEM_SIZE; + i += EVENT_ELEM_SIZE) { + ev = ipw_read_reg32(priv, base + i); + time = ipw_read_reg32(priv, base + i + 1*sizeof(u32)); + data = ipw_read_reg32(priv, base + i + 2*sizeof(u32)); + +#ifdef CONFIG_IPW_DEBUG + IPW_ERROR("%i\t0x%08x\t%i\n", time, data, ev); +#endif + } +} + +static int ipw_get_ordinal(struct ipw_priv *priv, u32 ord, void *val, + u32 *len) +{ + u32 addr, field_info, field_len, field_count, total_len; + + IPW_DEBUG_ORD("ordinal = %i\n", ord); + + if (!priv || !val || !len) { + IPW_DEBUG_ORD("Invalid argument\n"); + return -EINVAL; + } + + /* verify device ordinal tables have been initialized */ + if (!priv->table0_addr || !priv->table1_addr || !priv->table2_addr) { + IPW_DEBUG_ORD("Access ordinals before initialization\n"); + return -EINVAL; + } + + switch (IPW_ORD_TABLE_ID_MASK & ord) { + case IPW_ORD_TABLE_0_MASK: + /* + * TABLE 0: Direct access to a table of 32 bit values + * + * This is a very simple table with the data directly + * read from the table + */ + + /* remove the table id from the ordinal */ + ord &= IPW_ORD_TABLE_VALUE_MASK; + + /* boundary check */ + if (ord > priv->table0_len) { + IPW_DEBUG_ORD("ordinal value (%i) longer then " + "max (%i)\n", ord, priv->table0_len); + return -EINVAL; + } + + /* verify we have enough room to store the value */ + if (*len < sizeof(u32)) { + IPW_DEBUG_ORD("ordinal buffer length too small, " + "need %d\n", sizeof(u32)); + return -EINVAL; + } + + IPW_DEBUG_ORD("Reading TABLE0[%i] from offset 0x%08x\n", + ord, priv->table0_addr + (ord << 2)); + + *len = sizeof(u32); + ord <<= 2; + *((u32 *)val) = ipw_read32(priv, priv->table0_addr + ord); + break; + + case IPW_ORD_TABLE_1_MASK: + /* + * TABLE 1: Indirect access to a table of 32 bit values + * + * This is a fairly large table of u32 values each + * representing starting addr for the data (which is + * also a u32) + */ + + /* remove the table id from the ordinal */ + ord &= IPW_ORD_TABLE_VALUE_MASK; + + /* boundary check */ + if (ord > priv->table1_len) { + IPW_DEBUG_ORD("ordinal value too long\n"); + return -EINVAL; + } + + /* verify we have enough room to store the value */ + if (*len < sizeof(u32)) { + IPW_DEBUG_ORD("ordinal buffer length too small, " + "need %d\n", sizeof(u32)); + return -EINVAL; + } + + *((u32 *)val) = ipw_read_reg32(priv, (priv->table1_addr + (ord << 2))); + *len = sizeof(u32); + break; + + case IPW_ORD_TABLE_2_MASK: + /* + * TABLE 2: Indirect access to a table of variable sized values + * + * This table consist of six values, each containing + * - dword containing the starting offset of the data + * - dword containing the lengh in the first 16bits + * and the count in the second 16bits + */ + + /* remove the table id from the ordinal */ + ord &= IPW_ORD_TABLE_VALUE_MASK; + + /* boundary check */ + if (ord > priv->table2_len) { + IPW_DEBUG_ORD("ordinal value too long\n"); + return -EINVAL; + } + + /* get the address of statistic */ + addr = ipw_read_reg32(priv, priv->table2_addr + (ord << 3)); + + /* get the second DW of statistics ; + * two 16-bit words - first is length, second is count */ + field_info = ipw_read_reg32(priv, priv->table2_addr + (ord << 3) + sizeof(u32)); + + /* get each entry length */ + field_len = *((u16 *)&field_info); + + /* get number of entries */ + field_count = *(((u16 *)&field_info) + 1); + + /* abort if not enought memory */ + total_len = field_len * field_count; + if (total_len > *len) { + *len = total_len; + return -EINVAL; + } + + *len = total_len; + if (!total_len) + return 0; + + IPW_DEBUG_ORD("addr = 0x%08x, total_len = %i, " + "field_info = 0x%08x\n", + addr, total_len, field_info); + ipw_read_indirect(priv, addr, val, total_len); + break; + + default: + IPW_DEBUG_ORD("Invalid ordinal!\n"); + return -EINVAL; + + } + + + return 0; +} + +static void ipw_init_ordinals(struct ipw_priv *priv) +{ + priv->table0_addr = IPW_ORDINALS_TABLE_LOWER; + priv->table0_len = ipw_read32(priv, priv->table0_addr); + + IPW_DEBUG_ORD("table 0 offset at 0x%08x, len = %i\n", + priv->table0_addr, priv->table0_len); + + priv->table1_addr = ipw_read32(priv, IPW_ORDINALS_TABLE_1); + priv->table1_len = ipw_read_reg32(priv, priv->table1_addr); + + IPW_DEBUG_ORD("table 1 offset at 0x%08x, len = %i\n", + priv->table1_addr, priv->table1_len); + + priv->table2_addr = ipw_read32(priv, IPW_ORDINALS_TABLE_2); + priv->table2_len = ipw_read_reg32(priv, priv->table2_addr); + priv->table2_len &= 0x0000ffff; /* use first two bytes */ + + IPW_DEBUG_ORD("table 2 offset at 0x%08x, len = %i\n", + priv->table2_addr, priv->table2_len); + +} + +/* + * The following adds a new attribute to the sysfs representation + * of this device driver (i.e. a new file in /sys/bus/pci/drivers/ipw/) + * used for controling the debug level. + * + * See the level definitions in ipw for details. + */ +static ssize_t show_debug_level(struct device_driver *d, char *buf) +{ + return sprintf(buf, "0x%08X\n", ipw_debug_level); +} +static ssize_t store_debug_level(struct device_driver *d, const char *buf, + size_t count) +{ + char *p = (char *)buf; + u32 val; + + if (p[1] == 'x' || p[1] == 'X' || p[0] == 'x' || p[0] == 'X') { + p++; + if (p[0] == 'x' || p[0] == 'X') + p++; + val = simple_strtoul(p, &p, 16); + } else + val = simple_strtoul(p, &p, 10); + if (p == buf) + printk(KERN_INFO DRV_NAME + ": %s is not in hex or decimal form.\n", buf); + else + ipw_debug_level = val; + + return strnlen(buf, count); +} + +static DRIVER_ATTR(debug_level, S_IWUSR | S_IRUGO, + show_debug_level, store_debug_level); + +static ssize_t show_status(struct device *d, char *buf) +{ + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + return sprintf(buf, "0x%08x\n", (int)p->status); +} +static DEVICE_ATTR(status, S_IRUGO, show_status, NULL); + +static ssize_t show_cfg(struct device *d, char *buf) +{ + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + return sprintf(buf, "0x%08x\n", (int)p->config); +} +static DEVICE_ATTR(cfg, S_IRUGO, show_cfg, NULL); + +static ssize_t show_nic_type(struct device *d, char *buf) +{ + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + u8 type = p->eeprom[EEPROM_NIC_TYPE]; + + switch (type) { + case EEPROM_NIC_TYPE_STANDARD: + return sprintf(buf, "STANDARD\n"); + case EEPROM_NIC_TYPE_DELL: + return sprintf(buf, "DELL\n"); + case EEPROM_NIC_TYPE_FUJITSU: + return sprintf(buf, "FUJITSU\n"); + case EEPROM_NIC_TYPE_IBM: + return sprintf(buf, "IBM\n"); + case EEPROM_NIC_TYPE_HP: + return sprintf(buf, "HP\n"); + } + + return sprintf(buf, "UNKNOWN\n"); +} +static DEVICE_ATTR(nic_type, S_IRUGO, show_nic_type, NULL); + +static ssize_t dump_error_log(struct device *d, const char *buf, + size_t count) +{ + char *p = (char *)buf; + + if (p[0] == '1') + ipw_dump_nic_error_log((struct ipw_priv*)d->driver_data); + + return strnlen(buf, count); +} +static DEVICE_ATTR(dump_errors, S_IWUSR, NULL, dump_error_log); + +static ssize_t dump_event_log(struct device *d, const char *buf, + size_t count) +{ + char *p = (char *)buf; + + if (p[0] == '1') + ipw_dump_nic_event_log((struct ipw_priv*)d->driver_data); + + return strnlen(buf, count); +} +static DEVICE_ATTR(dump_events, S_IWUSR, NULL, dump_event_log); + +static ssize_t show_ucode_version(struct device *d, char *buf) +{ + u32 len = sizeof(u32), tmp = 0; + struct ipw_priv *p = (struct ipw_priv*)d->driver_data; + + if(ipw_get_ordinal(p, IPW_ORD_STAT_UCODE_VERSION, &tmp, &len)) + return 0; + + return sprintf(buf, "0x%08x\n", tmp); +} +static DEVICE_ATTR(ucode_version, S_IWUSR|S_IRUGO, show_ucode_version, NULL); + +static ssize_t show_rtc(struct device *d, char *buf) +{ + u32 len = sizeof(u32), tmp = 0; + struct ipw_priv *p = (struct ipw_priv*)d->driver_data; + + if(ipw_get_ordinal(p, IPW_ORD_STAT_RTC, &tmp, &len)) + return 0; + + return sprintf(buf, "0x%08x\n", tmp); +} +static DEVICE_ATTR(rtc, S_IWUSR|S_IRUGO, show_rtc, NULL); + +/* + * Add a device attribute to view/control the delay between eeprom + * operations. + */ +static ssize_t show_eeprom_delay(struct device *d, char *buf) +{ + int n = ((struct ipw_priv*)d->driver_data)->eeprom_delay; + return sprintf(buf, "%i\n", n); +} +static ssize_t store_eeprom_delay(struct device *d, const char *buf, + size_t count) +{ + struct ipw_priv *p = (struct ipw_priv*)d->driver_data; + sscanf(buf, "%i", &p->eeprom_delay); + return strnlen(buf, count); +} +static DEVICE_ATTR(eeprom_delay, S_IWUSR|S_IRUGO, + show_eeprom_delay,store_eeprom_delay); + +static ssize_t show_command_event_reg(struct device *d, char *buf) +{ + u32 reg = 0; + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + + reg = ipw_read_reg32(p, CX2_INTERNAL_CMD_EVENT); + return sprintf(buf, "0x%08x\n", reg); +} +static ssize_t store_command_event_reg(struct device *d, + const char *buf, + size_t count) +{ + u32 reg; + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + + sscanf(buf, "%x", ®); + ipw_write_reg32(p, CX2_INTERNAL_CMD_EVENT, reg); + return strnlen(buf, count); +} +static DEVICE_ATTR(command_event_reg, S_IWUSR|S_IRUGO, + show_command_event_reg,store_command_event_reg); + +static ssize_t show_mem_gpio_reg(struct device *d, char *buf) +{ + u32 reg = 0; + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + + reg = ipw_read_reg32(p, 0x301100); + return sprintf(buf, "0x%08x\n", reg); +} +static ssize_t store_mem_gpio_reg(struct device *d, + const char *buf, + size_t count) +{ + u32 reg; + struct ipw_priv *p = (struct ipw_priv *)d->driver_data; + + sscanf(buf, "%x", ®); + ipw_write_reg32(p, 0x301100, reg); + return strnlen(buf, count); +} +static DEVICE_ATTR(mem_gpio_reg, S_IWUSR|S_IRUGO, + show_mem_gpio_reg,store_mem_gpio_reg); + +static ssize_t show_indirect_dword(struct device *d, char *buf) +{ + u32 reg = 0; + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + if (priv->status & STATUS_INDIRECT_DWORD) + reg = ipw_read_reg32(priv, priv->indirect_dword); + else + reg = 0; + + return sprintf(buf, "0x%08x\n", reg); +} +static ssize_t store_indirect_dword(struct device *d, + const char *buf, + size_t count) +{ + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + + sscanf(buf, "%x", &priv->indirect_dword); + priv->status |= STATUS_INDIRECT_DWORD; + return strnlen(buf, count); +} +static DEVICE_ATTR(indirect_dword, S_IWUSR|S_IRUGO, + show_indirect_dword,store_indirect_dword); + +static ssize_t show_indirect_byte(struct device *d, char *buf) +{ + u8 reg = 0; + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + if (priv->status & STATUS_INDIRECT_BYTE) + reg = ipw_read_reg8(priv, priv->indirect_byte); + else + reg = 0; + + return sprintf(buf, "0x%02x\n", reg); +} +static ssize_t store_indirect_byte(struct device *d, + const char *buf, + size_t count) +{ + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + + sscanf(buf, "%x", &priv->indirect_byte); + priv->status |= STATUS_INDIRECT_BYTE; + return strnlen(buf, count); +} +static DEVICE_ATTR(indirect_byte, S_IWUSR|S_IRUGO, + show_indirect_byte, store_indirect_byte); + +static ssize_t show_direct_dword(struct device *d, char *buf) +{ + u32 reg = 0; + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + + if (priv->status & STATUS_DIRECT_DWORD) + reg = ipw_read32(priv, priv->direct_dword); + else + reg = 0; + + return sprintf(buf, "0x%08x\n", reg); +} +static ssize_t store_direct_dword(struct device *d, + const char *buf, + size_t count) +{ + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + + sscanf(buf, "%x", &priv->direct_dword); + priv->status |= STATUS_DIRECT_DWORD; + return strnlen(buf, count); +} +static DEVICE_ATTR(direct_dword, S_IWUSR|S_IRUGO, + show_direct_dword,store_direct_dword); + + +static inline int rf_kill_active(struct ipw_priv *priv) +{ + if (0 == (ipw_read32(priv, 0x30) & 0x10000)) + priv->status |= STATUS_RF_KILL_HW; + else + priv->status &= ~STATUS_RF_KILL_HW; + + return (priv->status & STATUS_RF_KILL_HW) ? 1 : 0; +} + +static ssize_t show_rf_kill(struct device *d, char *buf) +{ + /* 0 - RF kill not enabled + 1 - SW based RF kill active (sysfs) + 2 - HW based RF kill active + 3 - Both HW and SW baed RF kill active */ + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + int val = ((priv->status & STATUS_RF_KILL_SW) ? 0x1 : 0x0) | + (rf_kill_active(priv) ? 0x2 : 0x0); + return sprintf(buf, "%i\n", val); +} + +static int ipw_radio_kill_sw(struct ipw_priv *priv, int disable_radio) +{ + if ((disable_radio ? 1 : 0) == + (priv->status & STATUS_RF_KILL_SW ? 1 : 0)) + return 0 ; + + IPW_DEBUG_RF_KILL("Manual SW RF Kill set to: RADIO %s\n", + disable_radio ? "OFF" : "ON"); + + if (disable_radio) { + priv->status |= STATUS_RF_KILL_SW; + + if (priv->workqueue) { + cancel_delayed_work(&priv->request_scan); + } + wake_up_interruptible(&priv->wait_command_queue); + queue_work(priv->workqueue, &priv->down); + } else { + priv->status &= ~STATUS_RF_KILL_SW; + if (rf_kill_active(priv)) { + IPW_DEBUG_RF_KILL("Can not turn radio back on - " + "disabled by HW switch\n"); + /* Make sure the RF_KILL check timer is running */ + cancel_delayed_work(&priv->rf_kill); + queue_delayed_work(priv->workqueue, &priv->rf_kill, + 2 * HZ); + } else + queue_work(priv->workqueue, &priv->up); + } + + return 1; +} + +static ssize_t store_rf_kill(struct device *d, const char *buf, size_t count) +{ + struct ipw_priv *priv = (struct ipw_priv *)d->driver_data; + + ipw_radio_kill_sw(priv, buf[0] == '1'); + + return count; +} +static DEVICE_ATTR(rf_kill, S_IWUSR|S_IRUGO, show_rf_kill, store_rf_kill); + +static void ipw_irq_tasklet(struct ipw_priv *priv) +{ + u32 inta, inta_mask, handled = 0; + unsigned long flags; + int rc = 0; + + spin_lock_irqsave(&priv->lock, flags); + + inta = ipw_read32(priv, CX2_INTA_RW); + inta_mask = ipw_read32(priv, CX2_INTA_MASK_R); + inta &= (CX2_INTA_MASK_ALL & inta_mask); + + /* Add any cached INTA values that need to be handled */ + inta |= priv->isr_inta; + + /* handle all the justifications for the interrupt */ + if (inta & CX2_INTA_BIT_RX_TRANSFER) { + ipw_rx(priv); + handled |= CX2_INTA_BIT_RX_TRANSFER; + } + + if (inta & CX2_INTA_BIT_TX_CMD_QUEUE) { + IPW_DEBUG_HC("Command completed.\n"); + rc = ipw_queue_tx_reclaim( priv, &priv->txq_cmd, -1); + priv->status &= ~STATUS_HCMD_ACTIVE; + wake_up_interruptible(&priv->wait_command_queue); + handled |= CX2_INTA_BIT_TX_CMD_QUEUE; + } + + if (inta & CX2_INTA_BIT_TX_QUEUE_1) { + IPW_DEBUG_TX("TX_QUEUE_1\n"); + rc = ipw_queue_tx_reclaim( priv, &priv->txq[0], 0); + handled |= CX2_INTA_BIT_TX_QUEUE_1; + } + + if (inta & CX2_INTA_BIT_TX_QUEUE_2) { + IPW_DEBUG_TX("TX_QUEUE_2\n"); + rc = ipw_queue_tx_reclaim( priv, &priv->txq[1], 1); + handled |= CX2_INTA_BIT_TX_QUEUE_2; + } + + if (inta & CX2_INTA_BIT_TX_QUEUE_3) { + IPW_DEBUG_TX("TX_QUEUE_3\n"); + rc = ipw_queue_tx_reclaim( priv, &priv->txq[2], 2); + handled |= CX2_INTA_BIT_TX_QUEUE_3; + } + + if (inta & CX2_INTA_BIT_TX_QUEUE_4) { + IPW_DEBUG_TX("TX_QUEUE_4\n"); + rc = ipw_queue_tx_reclaim( priv, &priv->txq[3], 3); + handled |= CX2_INTA_BIT_TX_QUEUE_4; + } + + if (inta & CX2_INTA_BIT_STATUS_CHANGE) { + IPW_WARNING("STATUS_CHANGE\n"); + handled |= CX2_INTA_BIT_STATUS_CHANGE; + } + + if (inta & CX2_INTA_BIT_BEACON_PERIOD_EXPIRED) { + IPW_WARNING("TX_PERIOD_EXPIRED\n"); + handled |= CX2_INTA_BIT_BEACON_PERIOD_EXPIRED; + } + + if (inta & CX2_INTA_BIT_SLAVE_MODE_HOST_CMD_DONE) { + IPW_WARNING("HOST_CMD_DONE\n"); + handled |= CX2_INTA_BIT_SLAVE_MODE_HOST_CMD_DONE; + } + + if (inta & CX2_INTA_BIT_FW_INITIALIZATION_DONE) { + IPW_WARNING("FW_INITIALIZATION_DONE\n"); + handled |= CX2_INTA_BIT_FW_INITIALIZATION_DONE; + } + + if (inta & CX2_INTA_BIT_FW_CARD_DISABLE_PHY_OFF_DONE) { + IPW_WARNING("PHY_OFF_DONE\n"); + handled |= CX2_INTA_BIT_FW_CARD_DISABLE_PHY_OFF_DONE; + } + + if (inta & CX2_INTA_BIT_RF_KILL_DONE) { + IPW_DEBUG_RF_KILL("RF_KILL_DONE\n"); + priv->status |= STATUS_RF_KILL_HW; + wake_up_interruptible(&priv->wait_command_queue); + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); + cancel_delayed_work(&priv->request_scan); + queue_delayed_work(priv->workqueue, &priv->rf_kill, 2 * HZ); + handled |= CX2_INTA_BIT_RF_KILL_DONE; + } + + if (inta & CX2_INTA_BIT_FATAL_ERROR) { + IPW_ERROR("Firmware error detected. Restarting.\n"); +#ifdef CONFIG_IPW_DEBUG + if (ipw_debug_level & IPW_DL_FW_ERRORS) { + ipw_dump_nic_error_log(priv); + ipw_dump_nic_event_log(priv); + } +#endif + queue_work(priv->workqueue, &priv->adapter_restart); + handled |= CX2_INTA_BIT_FATAL_ERROR; + } + + if (inta & CX2_INTA_BIT_PARITY_ERROR) { + IPW_ERROR("Parity error\n"); + handled |= CX2_INTA_BIT_PARITY_ERROR; + } + + if (handled != inta) { + IPW_ERROR("Unhandled INTA bits 0x%08x\n", + inta & ~handled); + } + + /* enable all interrupts */ + ipw_enable_interrupts(priv); + + spin_unlock_irqrestore(&priv->lock, flags); +} + +#ifdef CONFIG_IPW_DEBUG +#define IPW_CMD(x) case IPW_CMD_ ## x : return #x +static char *get_cmd_string(u8 cmd) +{ + switch (cmd) { + IPW_CMD(HOST_COMPLETE); + IPW_CMD(POWER_DOWN); + IPW_CMD(SYSTEM_CONFIG); + IPW_CMD(MULTICAST_ADDRESS); + IPW_CMD(SSID); + IPW_CMD(ADAPTER_ADDRESS); + IPW_CMD(PORT_TYPE); + IPW_CMD(RTS_THRESHOLD); + IPW_CMD(FRAG_THRESHOLD); + IPW_CMD(POWER_MODE); + IPW_CMD(WEP_KEY); + IPW_CMD(TGI_TX_KEY); + IPW_CMD(SCAN_REQUEST); + IPW_CMD(SCAN_REQUEST_EXT); + IPW_CMD(ASSOCIATE); + IPW_CMD(SUPPORTED_RATES); + IPW_CMD(SCAN_ABORT); + IPW_CMD(TX_FLUSH); + IPW_CMD(QOS_PARAMETERS); + IPW_CMD(DINO_CONFIG); + IPW_CMD(RSN_CAPABILITIES); + IPW_CMD(RX_KEY); + IPW_CMD(CARD_DISABLE); + IPW_CMD(SEED_NUMBER); + IPW_CMD(TX_POWER); + IPW_CMD(COUNTRY_INFO); + IPW_CMD(AIRONET_INFO); + IPW_CMD(AP_TX_POWER); + IPW_CMD(CCKM_INFO); + IPW_CMD(CCX_VER_INFO); + IPW_CMD(SET_CALIBRATION); + IPW_CMD(SENSITIVITY_CALIB); + IPW_CMD(RETRY_LIMIT); + IPW_CMD(IPW_PRE_POWER_DOWN); + IPW_CMD(VAP_BEACON_TEMPLATE); + IPW_CMD(VAP_DTIM_PERIOD); + IPW_CMD(EXT_SUPPORTED_RATES); + IPW_CMD(VAP_LOCAL_TX_PWR_CONSTRAINT); + IPW_CMD(VAP_QUIET_INTERVALS); + IPW_CMD(VAP_CHANNEL_SWITCH); + IPW_CMD(VAP_MANDATORY_CHANNELS); + IPW_CMD(VAP_CELL_PWR_LIMIT); + IPW_CMD(VAP_CF_PARAM_SET); + IPW_CMD(VAP_SET_BEACONING_STATE); + IPW_CMD(MEASUREMENT); + IPW_CMD(POWER_CAPABILITY); + IPW_CMD(SUPPORTED_CHANNELS); + IPW_CMD(TPC_REPORT); + IPW_CMD(WME_INFO); + IPW_CMD(PRODUCTION_COMMAND); + default: + return "UNKNOWN"; + } +} +#endif /* CONFIG_IPW_DEBUG */ + +#define HOST_COMPLETE_TIMEOUT HZ +static int ipw_send_cmd(struct ipw_priv *priv, struct host_cmd *cmd) +{ + int rc = 0; + + if (priv->status & STATUS_HCMD_ACTIVE) { + IPW_ERROR("Already sending a command\n"); + return -1; + } + + priv->status |= STATUS_HCMD_ACTIVE; + + IPW_DEBUG_HC("Sending %s command (#%d), %d bytes\n", + get_cmd_string(cmd->cmd), cmd->cmd, cmd->len); + printk_buf(IPW_DL_HOST_COMMAND, (u8*)cmd->param, cmd->len); + + rc = ipw_queue_tx_hcmd(priv, cmd->cmd, &cmd->param, cmd->len, 0); + if (rc) + return rc; + + rc = wait_event_interruptible_timeout( + priv->wait_command_queue, !(priv->status & STATUS_HCMD_ACTIVE), + HOST_COMPLETE_TIMEOUT); + if (rc == 0) { + IPW_DEBUG_INFO("Command completion failed out after %dms.\n", + HOST_COMPLETE_TIMEOUT / (HZ / 1000)); + priv->status &= ~STATUS_HCMD_ACTIVE; + return -EIO; + } + if (priv->status & STATUS_RF_KILL_MASK) { + IPW_DEBUG_INFO("Command aborted due to RF Kill Switch\n"); + return -EIO; + } + + return 0; +} + +static int ipw_send_host_complete(struct ipw_priv *priv) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_HOST_COMPLETE, + .len = 0 + }; + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send HOST_COMPLETE command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_system_config(struct ipw_priv *priv, + struct ipw_sys_config *config) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SYSTEM_CONFIG, + .len = sizeof(*config) + }; + + if (!priv || !config) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param,config,sizeof(*config)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SYSTEM_CONFIG command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_ssid(struct ipw_priv *priv, u8 *ssid, int len) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SSID, + .len = min(len, IW_ESSID_MAX_SIZE) + }; + + if (!priv || !ssid) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param, ssid, cmd.len); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SSID command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_adapter_address(struct ipw_priv *priv, u8 *mac) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_ADAPTER_ADDRESS, + .len = ETH_ALEN + }; + + if (!priv || !mac) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + IPW_DEBUG_INFO("%s: Setting MAC to " MAC_FMT "\n", + priv->net_dev->name, MAC_ARG(mac)); + + memcpy(&cmd.param, mac, ETH_ALEN); + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send ADAPTER_ADDRESS command\n"); + return -1; + } + + return 0; +} + +static void ipw_adapter_restart(void *adapter) +{ + struct ipw_priv *priv = adapter; + + if (priv->status & STATUS_RF_KILL_MASK) + return; + + ipw_down(priv); + if (ipw_up(priv)) { + IPW_ERROR("Failed to up device\n"); + return; + } +} + + + + +#define IPW_SCAN_CHECK_WATCHDOG (5 * HZ) + +static void ipw_scan_check(void *data) +{ + struct ipw_priv *priv = data; + if (priv->status & (STATUS_SCANNING | STATUS_SCAN_ABORTING)) { + IPW_DEBUG_SCAN("Scan completion watchdog resetting " + "adapter (%dms).\n", + IPW_SCAN_CHECK_WATCHDOG / 100); + ipw_adapter_restart(priv); + } +} + +static int ipw_send_scan_request_ext(struct ipw_priv *priv, + struct ipw_scan_request_ext *request) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SCAN_REQUEST_EXT, + .len = sizeof(*request) + }; + + if (!priv || !request) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param,request,sizeof(*request)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SCAN_REQUEST_EXT command\n"); + return -1; + } + + queue_delayed_work(priv->workqueue, &priv->scan_check, + IPW_SCAN_CHECK_WATCHDOG); + return 0; +} + +static int ipw_send_scan_abort(struct ipw_priv *priv) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SCAN_ABORT, + .len = 0 + }; + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SCAN_ABORT command\n"); + return -1; + } + + return 0; +} + +static int ipw_set_sensitivity(struct ipw_priv *priv, u16 sens) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SENSITIVITY_CALIB, + .len = sizeof(struct ipw_sensitivity_calib) + }; + struct ipw_sensitivity_calib *calib = (struct ipw_sensitivity_calib *) + &cmd.param; + calib->beacon_rssi_raw = sens; + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SENSITIVITY CALIB command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_associate(struct ipw_priv *priv, + struct ipw_associate *associate) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_ASSOCIATE, + .len = sizeof(*associate) + }; + + if (!priv || !associate) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param,associate,sizeof(*associate)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send ASSOCIATE command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_supported_rates(struct ipw_priv *priv, + struct ipw_supported_rates *rates) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SUPPORTED_RATES, + .len = sizeof(*rates) + }; + + if (!priv || !rates) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param,rates,sizeof(*rates)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SUPPORTED_RATES command\n"); + return -1; + } + + return 0; +} + +static int ipw_set_random_seed(struct ipw_priv *priv) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_SEED_NUMBER, + .len = sizeof(u32) + }; + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + get_random_bytes(&cmd.param, sizeof(u32)); + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send SEED_NUMBER command\n"); + return -1; + } + + return 0; +} + +#if 0 +static int ipw_send_card_disable(struct ipw_priv *priv, u32 phy_off) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_CARD_DISABLE, + .len = sizeof(u32) + }; + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + *((u32*)&cmd.param) = phy_off; + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send CARD_DISABLE command\n"); + return -1; + } + + return 0; +} +#endif + +static int ipw_send_tx_power(struct ipw_priv *priv, + struct ipw_tx_power *power) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_TX_POWER, + .len = sizeof(*power) + }; + + if (!priv || !power) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param,power,sizeof(*power)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send TX_POWER command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_rts_threshold(struct ipw_priv *priv, u16 rts) +{ + struct ipw_rts_threshold rts_threshold = { + .rts_threshold = rts, + }; + struct host_cmd cmd = { + .cmd = IPW_CMD_RTS_THRESHOLD, + .len = sizeof(rts_threshold) + }; + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param, &rts_threshold, sizeof(rts_threshold)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send RTS_THRESHOLD command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_frag_threshold(struct ipw_priv *priv, u16 frag) +{ + struct ipw_frag_threshold frag_threshold = { + .frag_threshold = frag, + }; + struct host_cmd cmd = { + .cmd = IPW_CMD_FRAG_THRESHOLD, + .len = sizeof(frag_threshold) + }; + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + memcpy(&cmd.param, &frag_threshold, sizeof(frag_threshold)); + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send FRAG_THRESHOLD command\n"); + return -1; + } + + return 0; +} + +static int ipw_send_power_mode(struct ipw_priv *priv, u32 mode) +{ + struct host_cmd cmd = { + .cmd = IPW_CMD_POWER_MODE, + .len = sizeof(u32) + }; + u32 *param = (u32*)(&cmd.param); + + if (!priv) { + IPW_ERROR("Invalid args\n"); + return -1; + } + + /* If on battery, set to 3, if AC set to CAM, else user + * level */ + switch (mode) { + case IPW_POWER_BATTERY: + *param = IPW_POWER_INDEX_3; + break; + case IPW_POWER_AC: + *param = IPW_POWER_MODE_CAM; + break; + default: + *param = mode; + break; + } + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send POWER_MODE command\n"); + return -1; + } + + return 0; +} + +/* + * The IPW device contains a Microwire compatible EEPROM that stores + * various data like the MAC address. Usually the firmware has exclusive + * access to the eeprom, but during device initialization (before the + * device driver has sent the HostComplete command to the firmware) the + * device driver has read access to the EEPROM by way of indirect addressing + * through a couple of memory mapped registers. + * + * The following is a simplified implementation for pulling data out of the + * the eeprom, along with some helper functions to find information in + * the per device private data's copy of the eeprom. + * + * NOTE: To better understand how these functions work (i.e what is a chip + * select and why do have to keep driving the eeprom clock?), read + * just about any data sheet for a Microwire compatible EEPROM. + */ + +/* write a 32 bit value into the indirect accessor register */ +static inline void eeprom_write_reg(struct ipw_priv *p, u32 data) +{ + ipw_write_reg32(p, FW_MEM_REG_EEPROM_ACCESS, data); + + /* the eeprom requires some time to complete the operation */ + udelay(p->eeprom_delay); + + return; +} + +/* perform a chip select operation */ +static inline void eeprom_cs(struct ipw_priv* priv) +{ + eeprom_write_reg(priv,0); + eeprom_write_reg(priv,EEPROM_BIT_CS); + eeprom_write_reg(priv,EEPROM_BIT_CS|EEPROM_BIT_SK); + eeprom_write_reg(priv,EEPROM_BIT_CS); +} + +/* perform a chip select operation */ +static inline void eeprom_disable_cs(struct ipw_priv* priv) +{ + eeprom_write_reg(priv,EEPROM_BIT_CS); + eeprom_write_reg(priv,0); + eeprom_write_reg(priv,EEPROM_BIT_SK); +} + +/* push a single bit down to the eeprom */ +static inline void eeprom_write_bit(struct ipw_priv *p,u8 bit) +{ + int d = ( bit ? EEPROM_BIT_DI : 0); + eeprom_write_reg(p,EEPROM_BIT_CS|d); + eeprom_write_reg(p,EEPROM_BIT_CS|d|EEPROM_BIT_SK); +} + +/* push an opcode followed by an address down to the eeprom */ +static void eeprom_op(struct ipw_priv* priv, u8 op, u8 addr) +{ + int i; + + eeprom_cs(priv); + eeprom_write_bit(priv,1); + eeprom_write_bit(priv,op&2); + eeprom_write_bit(priv,op&1); + for ( i=7; i>=0; i-- ) { + eeprom_write_bit(priv,addr&(1<<i)); + } +} + +/* pull 16 bits off the eeprom, one bit at a time */ +static u16 eeprom_read_u16(struct ipw_priv* priv, u8 addr) +{ + int i; + u16 r=0; + + /* Send READ Opcode */ + eeprom_op(priv,EEPROM_CMD_READ,addr); + + /* Send dummy bit */ + eeprom_write_reg(priv,EEPROM_BIT_CS); + + /* Read the byte off the eeprom one bit at a time */ + for ( i=0; i<16; i++ ) { + u32 data = 0; + eeprom_write_reg(priv,EEPROM_BIT_CS|EEPROM_BIT_SK); + eeprom_write_reg(priv,EEPROM_BIT_CS); + data = ipw_read_reg32(priv,FW_MEM_REG_EEPROM_ACCESS); + r = (r<<1) | ((data & EEPROM_BIT_DO)?1:0); + } + + /* Send another dummy bit */ + eeprom_write_reg(priv,0); + eeprom_disable_cs(priv); + + return r; +} + +/* helper function for pulling the mac address out of the private */ +/* data's copy of the eeprom data */ +static void eeprom_parse_mac(struct ipw_priv* priv, u8* mac) +{ + u8* ee = (u8*)priv->eeprom; + memcpy(mac, &ee[EEPROM_MAC_ADDRESS], 6); +} + +/* + * Either the device driver (i.e. the host) or the firmware can + * load eeprom data into the designated region in SRAM. If neither + * happens then the FW will shutdown with a fatal error. + * + * In order to signal the FW to load the EEPROM, the EEPROM_LOAD_DISABLE + * bit needs region of shared SRAM needs to be non-zero. + */ +static void ipw_eeprom_init_sram(struct ipw_priv *priv) +{ + int i; + u16 *eeprom = (u16 *)priv->eeprom; + + IPW_DEBUG_TRACE(">>\n"); + + /* read entire contents of eeprom into private buffer */ + for ( i=0; i<128; i++ ) + eeprom[i] = eeprom_read_u16(priv,(u8)i); + + /* + If the data looks correct, then copy it to our private + copy. Otherwise let the firmware know to perform the operation + on it's own + */ + if ((priv->eeprom + EEPROM_VERSION) != 0) { + IPW_DEBUG_INFO("Writing EEPROM data into SRAM\n"); + + /* write the eeprom data to sram */ + for( i=0; i<CX2_EEPROM_IMAGE_SIZE; i++ ) + ipw_write8(priv, IPW_EEPROM_DATA + i, + priv->eeprom[i]); + + /* Do not load eeprom data on fatal error or suspend */ + ipw_write32(priv, IPW_EEPROM_LOAD_DISABLE, 0); + } else { + IPW_DEBUG_INFO("Enabling FW initializationg of SRAM\n"); + + /* Load eeprom data on fatal error or suspend */ + ipw_write32(priv, IPW_EEPROM_LOAD_DISABLE, 1); + } + + IPW_DEBUG_TRACE("<<\n"); +} + + +static inline void ipw_zero_memory(struct ipw_priv *priv, u32 start, u32 count) +{ + count >>= 2; + if (!count) return; + _ipw_write32(priv, CX2_AUTOINC_ADDR, start); + while (count--) + _ipw_write32(priv, CX2_AUTOINC_DATA, 0); +} + +static inline void ipw_fw_dma_reset_command_blocks(struct ipw_priv *priv) +{ + ipw_zero_memory(priv, CX2_SHARED_SRAM_DMA_CONTROL, + CB_NUMBER_OF_ELEMENTS_SMALL * + sizeof(struct command_block)); +} + +static int ipw_fw_dma_enable(struct ipw_priv *priv) +{ /* start dma engine but no transfers yet*/ + + IPW_DEBUG_FW(">> : \n"); + + /* Start the dma */ + ipw_fw_dma_reset_command_blocks(priv); + + /* Write CB base address */ + ipw_write_reg32(priv, CX2_DMA_I_CB_BASE, CX2_SHARED_SRAM_DMA_CONTROL); + + IPW_DEBUG_FW("<< : \n"); + return 0; +} + +static void ipw_fw_dma_abort(struct ipw_priv *priv) +{ + u32 control = 0; + + IPW_DEBUG_FW(">> :\n"); + + //set the Stop and Abort bit + control = DMA_CONTROL_SMALL_CB_CONST_VALUE | DMA_CB_STOP_AND_ABORT; + ipw_write_reg32(priv, CX2_DMA_I_DMA_CONTROL, control); + priv->sram_desc.last_cb_index = 0; + + IPW_DEBUG_FW("<< \n"); +} + +static int ipw_fw_dma_write_command_block(struct ipw_priv *priv, int index, struct command_block *cb) +{ + u32 address = CX2_SHARED_SRAM_DMA_CONTROL + (sizeof(struct command_block) * index); + IPW_DEBUG_FW(">> :\n"); + + ipw_write_indirect(priv, address, (u8*)cb, sizeof(struct command_block)); + + IPW_DEBUG_FW("<< :\n"); + return 0; + +} + +static int ipw_fw_dma_kick(struct ipw_priv *priv) +{ + u32 control = 0; + u32 index=0; + + IPW_DEBUG_FW(">> :\n"); + + for (index = 0; index < priv->sram_desc.last_cb_index; index++) + ipw_fw_dma_write_command_block(priv, index, &priv->sram_desc.cb_list[index]); + + /* Enable the DMA in the CSR register */ + ipw_clear_bit(priv, CX2_RESET_REG,CX2_RESET_REG_MASTER_DISABLED | CX2_RESET_REG_STOP_MASTER); + + /* Set the Start bit. */ + control = DMA_CONTROL_SMALL_CB_CONST_VALUE | DMA_CB_START; + ipw_write_reg32(priv, CX2_DMA_I_DMA_CONTROL, control); + + IPW_DEBUG_FW("<< :\n"); + return 0; +} + +static void ipw_fw_dma_dump_command_block(struct ipw_priv *priv) +{ + u32 address; + u32 register_value=0; + u32 cb_fields_address=0; + + IPW_DEBUG_FW(">> :\n"); + address = ipw_read_reg32(priv,CX2_DMA_I_CURRENT_CB); + IPW_DEBUG_FW_INFO("Current CB is 0x%x \n",address); + + /* Read the DMA Controlor register */ + register_value = ipw_read_reg32(priv, CX2_DMA_I_DMA_CONTROL); + IPW_DEBUG_FW_INFO("CX2_DMA_I_DMA_CONTROL is 0x%x \n",register_value); + + /* Print the CB values*/ + cb_fields_address = address; + register_value = ipw_read_reg32(priv, cb_fields_address); + IPW_DEBUG_FW_INFO("Current CB ControlField is 0x%x \n",register_value); + + cb_fields_address += sizeof(u32); + register_value = ipw_read_reg32(priv, cb_fields_address); + IPW_DEBUG_FW_INFO("Current CB Source Field is 0x%x \n",register_value); + + cb_fields_address += sizeof(u32); + register_value = ipw_read_reg32(priv, cb_fields_address); + IPW_DEBUG_FW_INFO("Current CB Destination Field is 0x%x \n", + register_value); + + cb_fields_address += sizeof(u32); + register_value = ipw_read_reg32(priv, cb_fields_address); + IPW_DEBUG_FW_INFO("Current CB Status Field is 0x%x \n",register_value); + + IPW_DEBUG_FW(">> :\n"); +} + +static int ipw_fw_dma_command_block_index(struct ipw_priv *priv) +{ + u32 current_cb_address = 0; + u32 current_cb_index = 0; + + IPW_DEBUG_FW("<< :\n"); + current_cb_address= ipw_read_reg32(priv, CX2_DMA_I_CURRENT_CB); + + current_cb_index = (current_cb_address - CX2_SHARED_SRAM_DMA_CONTROL )/ + sizeof (struct command_block); + + IPW_DEBUG_FW_INFO("Current CB index 0x%x address = 0x%X \n", + current_cb_index, current_cb_address ); + + IPW_DEBUG_FW(">> :\n"); + return current_cb_index; + +} + +static int ipw_fw_dma_add_command_block(struct ipw_priv *priv, + u32 src_address, + u32 dest_address, + u32 length, + int interrupt_enabled, + int is_last) +{ + + u32 control = CB_VALID | CB_SRC_LE | CB_DEST_LE | CB_SRC_AUTOINC | + CB_SRC_IO_GATED | CB_DEST_AUTOINC | CB_SRC_SIZE_LONG | + CB_DEST_SIZE_LONG; + struct command_block *cb; + u32 last_cb_element=0; + + IPW_DEBUG_FW_INFO("src_address=0x%x dest_address=0x%x length=0x%x\n", + src_address, dest_address, length); + + if (priv->sram_desc.last_cb_index >= CB_NUMBER_OF_ELEMENTS_SMALL) + return -1; + + last_cb_element = priv->sram_desc.last_cb_index; + cb = &priv->sram_desc.cb_list[last_cb_element]; + priv->sram_desc.last_cb_index++; + + /* Calculate the new CB control word */ + if (interrupt_enabled ) + control |= CB_INT_ENABLED; + + if (is_last) + control |= CB_LAST_VALID; + + control |= length; + + /* Calculate the CB Element's checksum value */ + cb->status = control ^src_address ^dest_address; + + /* Copy the Source and Destination addresses */ + cb->dest_addr = dest_address; + cb->source_addr = src_address; + + /* Copy the Control Word last */ + cb->control = control; + + return 0; +} + +static int ipw_fw_dma_add_buffer(struct ipw_priv *priv, + u32 src_phys, + u32 dest_address, + u32 length) +{ + u32 bytes_left = length; + u32 src_offset=0; + u32 dest_offset=0; + int status = 0; + IPW_DEBUG_FW(">> \n"); + IPW_DEBUG_FW_INFO("src_phys=0x%x dest_address=0x%x length=0x%x\n", + src_phys, dest_address, length); + while (bytes_left > CB_MAX_LENGTH) { + status = ipw_fw_dma_add_command_block( priv, + src_phys + src_offset, + dest_address + dest_offset, + CB_MAX_LENGTH, 0, 0); + if (status) { + IPW_DEBUG_FW_INFO(": Failed\n"); + return -1; + } else + IPW_DEBUG_FW_INFO(": Added new cb\n"); + + src_offset += CB_MAX_LENGTH; + dest_offset += CB_MAX_LENGTH; + bytes_left -= CB_MAX_LENGTH; + } + + /* add the buffer tail */ + if (bytes_left > 0) { + status = ipw_fw_dma_add_command_block( + priv, src_phys + src_offset, + dest_address + dest_offset, + bytes_left, 0, 0); + if (status) { + IPW_DEBUG_FW_INFO(": Failed on the buffer tail\n"); + return -1; + } else + IPW_DEBUG_FW_INFO(": Adding new cb - the buffer tail\n"); + } + + + IPW_DEBUG_FW("<< \n"); + return 0; +} + +static int ipw_fw_dma_wait(struct ipw_priv *priv) +{ + u32 current_index = 0; + u32 watchdog = 0; + + IPW_DEBUG_FW(">> : \n"); + + current_index = ipw_fw_dma_command_block_index(priv); + IPW_DEBUG_FW_INFO("sram_desc.last_cb_index:0x%8X\n", + (int) priv->sram_desc.last_cb_index); + + while (current_index < priv->sram_desc.last_cb_index) { + udelay(50); + current_index = ipw_fw_dma_command_block_index(priv); + + watchdog++; + + if (watchdog > 400) { + IPW_DEBUG_FW_INFO("Timeout\n"); + ipw_fw_dma_dump_command_block(priv); + ipw_fw_dma_abort(priv); + return -1; + } + } + + ipw_fw_dma_abort(priv); + + /*Disable the DMA in the CSR register*/ + ipw_set_bit(priv, CX2_RESET_REG, + CX2_RESET_REG_MASTER_DISABLED | CX2_RESET_REG_STOP_MASTER); + + IPW_DEBUG_FW("<< dmaWaitSync \n"); + return 0; +} + +static void ipw_remove_current_network(struct ipw_priv *priv) +{ + struct list_head *element, *safe; + struct ieee80211_network *network = NULL; + list_for_each_safe(element, safe, &priv->ieee->network_list) { + network = list_entry(element, struct ieee80211_network, list); + if (!memcmp(network->bssid, priv->bssid, ETH_ALEN)) { + list_del(element); + list_add_tail(&network->list, + &priv->ieee->network_free_list); + } + } +} + +/** + * Check that card is still alive. + * Reads debug register from domain0. + * If card is present, pre-defined value should + * be found there. + * + * @param priv + * @return 1 if card is present, 0 otherwise + */ +static inline int ipw_alive(struct ipw_priv *priv) +{ + return ipw_read32(priv, 0x90) == 0xd55555d5; +} + +static inline int ipw_poll_bit(struct ipw_priv *priv, u32 addr, u32 mask, + int timeout) +{ + int i = 0; + + do { + if ((ipw_read32(priv, addr) & mask) == mask) + return i; + mdelay(10); + i += 10; + } while (i < timeout); + + return -ETIME; +} + +/* These functions load the firmware and micro code for the operation of + * the ipw hardware. It assumes the buffer has all the bits for the + * image and the caller is handling the memory allocation and clean up. + */ + + +static int ipw_stop_master(struct ipw_priv * priv) +{ + int rc; + + IPW_DEBUG_TRACE(">> \n"); + /* stop master. typical delay - 0 */ + ipw_set_bit(priv, CX2_RESET_REG, CX2_RESET_REG_STOP_MASTER); + + rc = ipw_poll_bit(priv, CX2_RESET_REG, + CX2_RESET_REG_MASTER_DISABLED, 100); + if (rc < 0) { + IPW_ERROR("stop master failed in 10ms\n"); + return -1; + } + + IPW_DEBUG_INFO("stop master %dms\n", rc); + + return rc; +} + +static void ipw_arc_release(struct ipw_priv *priv) +{ + IPW_DEBUG_TRACE(">> \n"); + mdelay(5); + + ipw_clear_bit(priv, CX2_RESET_REG, CBD_RESET_REG_PRINCETON_RESET); + + /* no one knows timing, for safety add some delay */ + mdelay(5); +} + +struct fw_header { + u32 version; + u32 mode; +}; + +struct fw_chunk { + u32 address; + u32 length; +}; + +#define IPW_FW_MAJOR_VERSION 2 +#define IPW_FW_MINOR_VERSION 2 + +#define IPW_FW_MINOR(x) ((x & 0xff) >> 8) +#define IPW_FW_MAJOR(x) (x & 0xff) + +#define IPW_FW_VERSION ((IPW_FW_MINOR_VERSION << 8) | \ + IPW_FW_MAJOR_VERSION) + +#define IPW_FW_PREFIX "ipw-" __stringify(IPW_FW_MAJOR_VERSION) \ +"." __stringify(IPW_FW_MINOR_VERSION) "-" + +#if IPW_FW_MAJOR_VERSION >= 2 && IPW_FW_MINOR_VERSION > 0 +#define IPW_FW_NAME(x) IPW_FW_PREFIX "" x ".fw" +#else +#define IPW_FW_NAME(x) "ipw2200_" x ".fw" +#endif + +static int ipw_load_ucode(struct ipw_priv *priv, u8 * data, + size_t len) +{ + int rc = 0, i, addr; + u8 cr = 0; + u16 *image; + + image = (u16 *)data; + + IPW_DEBUG_TRACE(">> \n"); + + rc = ipw_stop_master(priv); + + if (rc < 0) + return rc; + +// spin_lock_irqsave(&priv->lock, flags); + + for (addr = CX2_SHARED_LOWER_BOUND; + addr < CX2_REGISTER_DOMAIN1_END; addr += 4) { + ipw_write32(priv, addr, 0); + } + + /* no ucode (yet) */ + memset(&priv->dino_alive, 0, sizeof(priv->dino_alive)); + /* destroy DMA queues */ + /* reset sequence */ + + ipw_write_reg32(priv, CX2_MEM_HALT_AND_RESET ,CX2_BIT_HALT_RESET_ON); + ipw_arc_release(priv); + ipw_write_reg32(priv, CX2_MEM_HALT_AND_RESET, CX2_BIT_HALT_RESET_OFF); + mdelay(1); + + /* reset PHY */ + ipw_write_reg32(priv, CX2_INTERNAL_CMD_EVENT, CX2_BASEBAND_POWER_DOWN); + mdelay(1); + + ipw_write_reg32(priv, CX2_INTERNAL_CMD_EVENT, 0); + mdelay(1); + + /* enable ucode store */ + ipw_write_reg8(priv, DINO_CONTROL_REG, 0x0); + ipw_write_reg8(priv, DINO_CONTROL_REG, DINO_ENABLE_CS); + mdelay(1); + + /* write ucode */ + /** + * @bug + * Do NOT set indirect address register once and then + * store data to indirect data register in the loop. + * It seems very reasonable, but in this case DINO do not + * accept ucode. It is essential to set address each time. + */ + /* load new ipw uCode */ + for (i = 0; i < len / 2; i++) + ipw_write_reg16(priv, CX2_BASEBAND_CONTROL_STORE, image[i]); + + + /* enable DINO */ + ipw_write_reg8(priv, CX2_BASEBAND_CONTROL_STATUS, 0); + ipw_write_reg8(priv, CX2_BASEBAND_CONTROL_STATUS, + DINO_ENABLE_SYSTEM ); + + /* this is where the igx / win driver deveates from the VAP driver.*/ + + /* wait for alive response */ + for (i = 0; i < 100; i++) { + /* poll for incoming data */ + cr = ipw_read_reg8(priv, CX2_BASEBAND_CONTROL_STATUS); + if (cr & DINO_RXFIFO_DATA) + break; + mdelay(1); + } + + if (cr & DINO_RXFIFO_DATA) { + /* alive_command_responce size is NOT multiple of 4 */ + u32 response_buffer[(sizeof(priv->dino_alive) + 3) / 4]; + + for (i = 0; i < ARRAY_SIZE(response_buffer); i++) + response_buffer[i] = + ipw_read_reg32(priv, + CX2_BASEBAND_RX_FIFO_READ); + memcpy(&priv->dino_alive, response_buffer, + sizeof(priv->dino_alive)); + if (priv->dino_alive.alive_command == 1 + && priv->dino_alive.ucode_valid == 1) { + rc = 0; + IPW_DEBUG_INFO( + "Microcode OK, rev. %d (0x%x) dev. %d (0x%x) " + "of %02d/%02d/%02d %02d:%02d\n", + priv->dino_alive.software_revision, + priv->dino_alive.software_revision, + priv->dino_alive.device_identifier, + priv->dino_alive.device_identifier, + priv->dino_alive.time_stamp[0], + priv->dino_alive.time_stamp[1], + priv->dino_alive.time_stamp[2], + priv->dino_alive.time_stamp[3], + priv->dino_alive.time_stamp[4]); + } else { + IPW_DEBUG_INFO("Microcode is not alive\n"); + rc = -EINVAL; + } + } else { + IPW_DEBUG_INFO("No alive response from DINO\n"); + rc = -ETIME; + } + + /* disable DINO, otherwise for some reason + firmware have problem getting alive resp. */ + ipw_write_reg8(priv, CX2_BASEBAND_CONTROL_STATUS, 0); + +// spin_unlock_irqrestore(&priv->lock, flags); + + return rc; +} + +static int ipw_load_firmware(struct ipw_priv *priv, u8 * data, + size_t len) +{ + int rc = -1; + int offset = 0; + struct fw_chunk *chunk; + dma_addr_t shared_phys; + u8 *shared_virt; + + IPW_DEBUG_TRACE("<< : \n"); + shared_virt = pci_alloc_consistent(priv->pci_dev, len, &shared_phys); + + if (!shared_virt) + return -ENOMEM; + + memmove(shared_virt, data, len); + + /* Start the Dma */ + rc = ipw_fw_dma_enable(priv); + + if (priv->sram_desc.last_cb_index > 0) { + /* the DMA is already ready this would be a bug. */ + BUG(); + goto out; + } + + do { + chunk = (struct fw_chunk *)(data + offset); + offset += sizeof(struct fw_chunk); + /* build DMA packet and queue up for sending */ + /* dma to chunk->address, the chunk->length bytes from data + + * offeset*/ + /* Dma loading */ + rc = ipw_fw_dma_add_buffer(priv, shared_phys + offset, + chunk->address, chunk->length); + if (rc) { + IPW_DEBUG_INFO("dmaAddBuffer Failed\n"); + goto out; + } + + offset += chunk->length; + } while (offset < len); + + /* Run the DMA and wait for the answer*/ + rc = ipw_fw_dma_kick(priv); + if (rc) { + IPW_ERROR("dmaKick Failed\n"); + goto out; + } + + rc = ipw_fw_dma_wait(priv); + if (rc) { + IPW_ERROR("dmaWaitSync Failed\n"); + goto out; + } + out: + pci_free_consistent( priv->pci_dev, len, shared_virt, shared_phys); + return rc; +} + +/* stop nic */ +static int ipw_stop_nic(struct ipw_priv *priv) +{ + int rc = 0; + + /* stop*/ + ipw_write32(priv, CX2_RESET_REG, CX2_RESET_REG_STOP_MASTER); + + rc = ipw_poll_bit(priv, CX2_RESET_REG, + CX2_RESET_REG_MASTER_DISABLED, 500); + if (rc < 0) { + IPW_ERROR("wait for reg master disabled failed\n"); + return rc; + } + + ipw_set_bit(priv, CX2_RESET_REG, CBD_RESET_REG_PRINCETON_RESET); + + return rc; +} + +static void ipw_start_nic(struct ipw_priv *priv) +{ + IPW_DEBUG_TRACE(">>\n"); + + /* prvHwStartNic release ARC*/ + ipw_clear_bit(priv, CX2_RESET_REG, + CX2_RESET_REG_MASTER_DISABLED | + CX2_RESET_REG_STOP_MASTER | + CBD_RESET_REG_PRINCETON_RESET); + + /* enable power management */ + ipw_set_bit(priv, CX2_GP_CNTRL_RW, CX2_GP_CNTRL_BIT_HOST_ALLOWS_STANDBY); + + IPW_DEBUG_TRACE("<<\n"); +} + +static int ipw_init_nic(struct ipw_priv *priv) +{ + int rc; + + IPW_DEBUG_TRACE(">>\n"); + /* reset */ + /*prvHwInitNic */ + /* set "initialization complete" bit to move adapter to D0 state */ + ipw_set_bit(priv, CX2_GP_CNTRL_RW, CX2_GP_CNTRL_BIT_INIT_DONE); + + /* low-level PLL activation */ + ipw_write32(priv, CX2_READ_INT_REGISTER, CX2_BIT_INT_HOST_SRAM_READ_INT_REGISTER); + + /* wait for clock stabilization */ + rc = ipw_poll_bit(priv, CX2_GP_CNTRL_RW, + CX2_GP_CNTRL_BIT_CLOCK_READY, 250); + if (rc < 0 ) + IPW_DEBUG_INFO("FAILED wait for clock stablization\n"); + + /* assert SW reset */ + ipw_set_bit(priv, CX2_RESET_REG, CX2_RESET_REG_SW_RESET); + + udelay(10); + + /* set "initialization complete" bit to move adapter to D0 state */ + ipw_set_bit(priv, CX2_GP_CNTRL_RW, CX2_GP_CNTRL_BIT_INIT_DONE); + + IPW_DEBUG_TRACE(">>\n"); + return 0; +} + + +/* Call this function from process context, it will sleep in request_firmware. + * Probe is an ok place to call this from. + */ +static int ipw_reset_nic(struct ipw_priv *priv) +{ + int rc = 0; + + IPW_DEBUG_TRACE(">>\n"); + + rc = ipw_init_nic(priv); + + /* Clear the 'host command active' bit... */ + priv->status &= ~STATUS_HCMD_ACTIVE; + wake_up_interruptible(&priv->wait_command_queue); + + IPW_DEBUG_TRACE("<<\n"); + return rc; +} + +static int ipw_get_fw(struct ipw_priv *priv, + const struct firmware **fw, const char *name) +{ + struct fw_header *header; + int rc; + + /* ask firmware_class module to get the boot firmware off disk */ + rc = request_firmware(fw, name, &priv->pci_dev->dev); + if (rc < 0) { + IPW_ERROR("%s load failed: Reason %d\n", name, rc); + return rc; + } + + header = (struct fw_header *)(*fw)->data; + if (IPW_FW_MAJOR(header->version) != IPW_FW_MAJOR_VERSION) { + IPW_ERROR("'%s' firmware version not compatible (%d != %d)\n", + name, + IPW_FW_MAJOR(header->version), IPW_FW_MAJOR_VERSION); + return -EINVAL; + } + + IPW_DEBUG_INFO("Loading firmware '%s' file v%d.%d (%d bytes)\n", + name, + IPW_FW_MAJOR(header->version), + IPW_FW_MINOR(header->version), + (*fw)->size - sizeof(struct fw_header)); + return 0; +} + +#define CX2_RX_BUF_SIZE (3000) + +static inline void ipw_rx_queue_reset(struct ipw_priv *priv, + struct ipw_rx_queue *rxq) +{ + unsigned long flags; + int i; + + spin_lock_irqsave(&rxq->lock, flags); + + INIT_LIST_HEAD(&rxq->rx_free); + INIT_LIST_HEAD(&rxq->rx_used); + + /* Fill the rx_used queue with _all_ of the Rx buffers */ + for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++) { + /* In the reset function, these buffers may have been allocated + * to an SKB, so we need to unmap and free potential storage */ + if (rxq->pool[i].skb != NULL) { + pci_unmap_single(priv->pci_dev, rxq->pool[i].dma_addr, + CX2_RX_BUF_SIZE, + PCI_DMA_FROMDEVICE); + dev_kfree_skb(rxq->pool[i].skb); + } + list_add_tail(&rxq->pool[i].list, &rxq->rx_used); + } + + /* Set us so that we have processed and used all buffers, but have + * not restocked the Rx queue with fresh buffers */ + rxq->read = rxq->write = 0; + rxq->processed = RX_QUEUE_SIZE - 1; + rxq->free_count = 0; + spin_unlock_irqrestore(&rxq->lock, flags); +} + +#ifdef CONFIG_PM +static int fw_loaded = 0; +static const struct firmware *bootfw = NULL; +static const struct firmware *firmware = NULL; +static const struct firmware *ucode = NULL; +#endif + +static int ipw_load(struct ipw_priv *priv) +{ +#ifndef CONFIG_PM + const struct firmware *bootfw = NULL; + const struct firmware *firmware = NULL; + const struct firmware *ucode = NULL; +#endif + int rc = 0, retries = 3; + +#ifdef CONFIG_PM + if (!fw_loaded) { +#endif + rc = ipw_get_fw(priv, &bootfw, IPW_FW_NAME("boot")); + if (rc) + goto error; + + switch (priv->ieee->iw_mode) { + case IW_MODE_ADHOC: + rc = ipw_get_fw(priv, &ucode, + IPW_FW_NAME("ibss_ucode")); + if (rc) + goto error; + + rc = ipw_get_fw(priv, &firmware, IPW_FW_NAME("ibss")); + break; + +#ifdef CONFIG_IPW_PROMISC + case IW_MODE_MONITOR: + rc = ipw_get_fw(priv, &ucode, + IPW_FW_NAME("ibss_ucode")); + if (rc) + goto error; + + rc = ipw_get_fw(priv, &firmware, IPW_FW_NAME("sniffer")); + break; +#endif + case IW_MODE_INFRA: + rc = ipw_get_fw(priv, &ucode, + IPW_FW_NAME("bss_ucode")); + if (rc) + goto error; + + rc = ipw_get_fw(priv, &firmware, IPW_FW_NAME("bss")); + break; + + default: + rc = -EINVAL; + } + + if (rc) + goto error; + +#ifdef CONFIG_PM + fw_loaded = 1; + } +#endif + + if (!priv->rxq) + priv->rxq = ipw_rx_queue_alloc(priv); + else + ipw_rx_queue_reset(priv, priv->rxq); + if (!priv->rxq) { + IPW_ERROR("Unable to initialize Rx queue\n"); + goto error; + } + + retry: + /* Ensure interrupts are disabled */ + ipw_write32(priv, CX2_INTA_MASK_R, ~CX2_INTA_MASK_ALL); + priv->status &= ~STATUS_INT_ENABLED; + + /* ack pending interrupts */ + ipw_write32(priv, CX2_INTA_RW, CX2_INTA_MASK_ALL); + + ipw_stop_nic(priv); + + rc = ipw_reset_nic(priv); + if (rc) { + IPW_ERROR("Unable to reset NIC\n"); + goto error; + } + + ipw_zero_memory(priv, CX2_NIC_SRAM_LOWER_BOUND, + CX2_NIC_SRAM_UPPER_BOUND - CX2_NIC_SRAM_LOWER_BOUND); + + /* DMA the initial boot firmware into the device */ + rc = ipw_load_firmware(priv, bootfw->data + sizeof(struct fw_header), + bootfw->size - sizeof(struct fw_header)); + if (rc < 0) { + IPW_ERROR("Unable to load boot firmware\n"); + goto error; + } + + /* kick start the device */ + ipw_start_nic(priv); + + /* wait for the device to finish it's initial startup sequence */ + rc = ipw_poll_bit(priv, CX2_INTA_RW, + CX2_INTA_BIT_FW_INITIALIZATION_DONE, 500); + if (rc < 0) { + IPW_ERROR("device failed to boot initial fw image\n"); + goto error; + } + IPW_DEBUG_INFO("initial device response after %dms\n", rc); + + /* ack fw init done interrupt */ + ipw_write32(priv, CX2_INTA_RW, CX2_INTA_BIT_FW_INITIALIZATION_DONE); + + /* DMA the ucode into the device */ + rc = ipw_load_ucode(priv, ucode->data + sizeof(struct fw_header), + ucode->size - sizeof(struct fw_header)); + if (rc < 0) { + IPW_ERROR("Unable to load ucode\n"); + goto error; + } + + /* stop nic */ + ipw_stop_nic(priv); + + /* DMA bss firmware into the device */ + rc = ipw_load_firmware(priv, firmware->data + + sizeof(struct fw_header), + firmware->size - sizeof(struct fw_header)); + if (rc < 0 ) { + IPW_ERROR("Unable to load firmware\n"); + goto error; + } + + ipw_write32(priv, IPW_EEPROM_LOAD_DISABLE, 0); + + rc = ipw_queue_reset(priv); + if (rc) { + IPW_ERROR("Unable to initialize queues\n"); + goto error; + } + + /* Ensure interrupts are disabled */ + ipw_write32(priv, CX2_INTA_MASK_R, ~CX2_INTA_MASK_ALL); + + /* kick start the device */ + ipw_start_nic(priv); + + if (ipw_read32(priv, CX2_INTA_RW) & CX2_INTA_BIT_PARITY_ERROR) { + if (retries > 0) { + IPW_WARNING("Parity error. Retrying init.\n"); + retries--; + goto retry; + } + + IPW_ERROR("TODO: Handle parity error -- schedule restart?\n"); + rc = -EIO; + goto error; + } + + /* wait for the device */ + rc = ipw_poll_bit(priv, CX2_INTA_RW, + CX2_INTA_BIT_FW_INITIALIZATION_DONE, 500); + if (rc < 0) { + IPW_ERROR("device failed to start after 500ms\n"); + goto error; + } + IPW_DEBUG_INFO("device response after %dms\n", rc); + + /* ack fw init done interrupt */ + ipw_write32(priv, CX2_INTA_RW, CX2_INTA_BIT_FW_INITIALIZATION_DONE); + + /* read eeprom data and initialize the eeprom region of sram */ + priv->eeprom_delay = 1; + ipw_eeprom_init_sram(priv); + + /* enable interrupts */ + ipw_enable_interrupts(priv); + + /* Ensure our queue has valid packets */ + ipw_rx_queue_replenish(priv); + + ipw_write32(priv, CX2_RX_READ_INDEX, priv->rxq->read); + + /* ack pending interrupts */ + ipw_write32(priv, CX2_INTA_RW, CX2_INTA_MASK_ALL); + +#ifndef CONFIG_PM + release_firmware(bootfw); + release_firmware(ucode); + release_firmware(firmware); +#endif + return 0; + + error: + if (priv->rxq) { + ipw_rx_queue_free(priv, priv->rxq); + priv->rxq = NULL; + } + ipw_tx_queue_free(priv); + if (bootfw) + release_firmware(bootfw); + if (ucode) + release_firmware(ucode); + if (firmware) + release_firmware(firmware); +#ifdef CONFIG_PM + fw_loaded = 0; + bootfw = ucode = firmware = NULL; +#endif + + return rc; +} + +/** + * DMA services + * + * Theory of operation + * + * A queue is a circular buffers with 'Read' and 'Write' pointers. + * 2 empty entries always kept in the buffer to protect from overflow. + * + * For Tx queue, there are low mark and high mark limits. If, after queuing + * the packet for Tx, free space become < low mark, Tx queue stopped. When + * reclaiming packets (on 'tx done IRQ), if free space become > high mark, + * Tx queue resumed. + * + * The IPW operates with six queues, one receive queue in the device's + * sram, one transmit queue for sending commands to the device firmware, + * and four transmit queues for data. + * + * The four transmit queues allow for performing quality of service (qos) + * transmissions as per the 802.11 protocol. Currently Linux does not + * provide a mechanism to the user for utilizing prioritized queues, so + * we only utilize the first data transmit queue (queue1). + */ + +/** + * Driver allocates buffers of this size for Rx + */ + +static inline int ipw_queue_space(const struct clx2_queue *q) +{ + int s = q->last_used - q->first_empty; + if (s <= 0) + s += q->n_bd; + s -= 2; /* keep some reserve to not confuse empty and full situations */ + if (s < 0) + s = 0; + return s; +} + +static inline int ipw_queue_inc_wrap(int index, int n_bd) +{ + return (++index == n_bd) ? 0 : index; +} + +/** + * Initialize common DMA queue structure + * + * @param q queue to init + * @param count Number of BD's to allocate. Should be power of 2 + * @param read_register Address for 'read' register + * (not offset within BAR, full address) + * @param write_register Address for 'write' register + * (not offset within BAR, full address) + * @param base_register Address for 'base' register + * (not offset within BAR, full address) + * @param size Address for 'size' register + * (not offset within BAR, full address) + */ +static void ipw_queue_init(struct ipw_priv *priv, struct clx2_queue *q, + int count, u32 read, u32 write, + u32 base, u32 size) +{ + q->n_bd = count; + + q->low_mark = q->n_bd / 4; + if (q->low_mark < 4) + q->low_mark = 4; + + q->high_mark = q->n_bd / 8; + if (q->high_mark < 2) + q->high_mark = 2; + + q->first_empty = q->last_used = 0; + q->reg_r = read; + q->reg_w = write; + + ipw_write32(priv, base, q->dma_addr); + ipw_write32(priv, size, count); + ipw_write32(priv, read, 0); + ipw_write32(priv, write, 0); + + _ipw_read32(priv, 0x90); +} + +static int ipw_queue_tx_init(struct ipw_priv *priv, + struct clx2_tx_queue *q, + int count, u32 read, u32 write, + u32 base, u32 size) +{ + struct pci_dev *dev = priv->pci_dev; + + q->txb = kmalloc(sizeof(q->txb[0]) * count, GFP_KERNEL); + if (!q->txb) { + IPW_ERROR("vmalloc for auxilary BD structures failed\n"); + return -ENOMEM; + } + + q->bd = pci_alloc_consistent(dev,sizeof(q->bd[0])*count, &q->q.dma_addr); + if (!q->bd) { + IPW_ERROR("pci_alloc_consistent(%d) failed\n", + sizeof(q->bd[0]) * count); + kfree(q->txb); + q->txb = NULL; + return -ENOMEM; + } + + ipw_queue_init(priv, &q->q, count, read, write, base, size); + return 0; +} + +/** + * Free one TFD, those at index [txq->q.last_used]. + * Do NOT advance any indexes + * + * @param dev + * @param txq + */ +static void ipw_queue_tx_free_tfd(struct ipw_priv *priv, + struct clx2_tx_queue *txq) +{ + struct tfd_frame *bd = &txq->bd[txq->q.last_used]; + struct pci_dev *dev = priv->pci_dev; + int i; + + /* classify bd */ + if (bd->control_flags.message_type == TX_HOST_COMMAND_TYPE) + /* nothing to cleanup after for host commands */ + return; + + /* sanity check */ + if (bd->u.data.num_chunks > NUM_TFD_CHUNKS) { + IPW_ERROR("Too many chunks: %i\n", bd->u.data.num_chunks); + /** @todo issue fatal error, it is quite serious situation */ + return; + } + + /* unmap chunks if any */ + for (i = 0; i < bd->u.data.num_chunks; i++) { + pci_unmap_single(dev, bd->u.data.chunk_ptr[i], + bd->u.data.chunk_len[i], PCI_DMA_TODEVICE); + if (txq->txb[txq->q.last_used]) { + ieee80211_txb_free(txq->txb[txq->q.last_used]); + txq->txb[txq->q.last_used] = NULL; + } + } +} + +/** + * Deallocate DMA queue. + * + * Empty queue by removing and destroying all BD's. + * Free all buffers. + * + * @param dev + * @param q + */ +static void ipw_queue_tx_free(struct ipw_priv *priv, + struct clx2_tx_queue *txq) +{ + struct clx2_queue *q = &txq->q; + struct pci_dev *dev = priv->pci_dev; + + if (q->n_bd == 0) + return; + + /* first, empty all BD's */ + for (; q->first_empty != q->last_used; + q->last_used = ipw_queue_inc_wrap(q->last_used, q->n_bd)) { + ipw_queue_tx_free_tfd(priv, txq); + } + + /* free buffers belonging to queue itself */ + pci_free_consistent(dev, sizeof(txq->bd[0])*q->n_bd, txq->bd, + q->dma_addr); + kfree(txq->txb); + + /* 0 fill whole structure */ + memset(txq, 0, sizeof(*txq)); +} + + +/** + * Destroy all DMA queues and structures + * + * @param priv + */ +static void ipw_tx_queue_free(struct ipw_priv *priv) +{ + /* Tx CMD queue */ + ipw_queue_tx_free(priv, &priv->txq_cmd); + + /* Tx queues */ + ipw_queue_tx_free(priv, &priv->txq[0]); + ipw_queue_tx_free(priv, &priv->txq[1]); + ipw_queue_tx_free(priv, &priv->txq[2]); + ipw_queue_tx_free(priv, &priv->txq[3]); +} + +static void inline __maybe_wake_tx(struct ipw_priv *priv) +{ + if (netif_running(priv->net_dev)) { + switch (priv->port_type) { + case DCR_TYPE_MU_BSS: + case DCR_TYPE_MU_IBSS: + if (!(priv->status & STATUS_ASSOCIATED)) { + return; + } + } + netif_wake_queue(priv->net_dev); + } + +} + +static inline void ipw_create_bssid(struct ipw_priv *priv, u8 *bssid) +{ + /* First 3 bytes are manufacturer */ + bssid[0] = priv->mac_addr[0]; + bssid[1] = priv->mac_addr[1]; + bssid[2] = priv->mac_addr[2]; + + /* Last bytes are random */ + get_random_bytes(&bssid[3], ETH_ALEN-3); + + bssid[0] &= 0xfe; /* clear multicast bit */ + bssid[0] |= 0x02; /* set local assignment bit (IEEE802) */ +} + +static inline u8 ipw_add_station(struct ipw_priv *priv, u8 *bssid) +{ + struct ipw_station_entry entry; + int i; + + for (i = 0; i < priv->num_stations; i++) { + if (!memcmp(priv->stations[i], bssid, ETH_ALEN)) { + /* Another node is active in network */ + priv->missed_adhoc_beacons = 0; + if (!(priv->config & CFG_STATIC_CHANNEL)) + /* when other nodes drop out, we drop out */ + priv->config &= ~CFG_ADHOC_PERSIST; + + return i; + } + } + + if (i == MAX_STATIONS) + return IPW_INVALID_STATION; + + IPW_DEBUG_SCAN("Adding AdHoc station: " MAC_FMT "\n", MAC_ARG(bssid)); + + entry.reserved = 0; + entry.support_mode = 0; + memcpy(entry.mac_addr, bssid, ETH_ALEN); + memcpy(priv->stations[i], bssid, ETH_ALEN); + ipw_write_direct(priv, IPW_STATION_TABLE_LOWER + i * sizeof(entry), + &entry, + sizeof(entry)); + priv->num_stations++; + + return i; +} + +static inline u8 ipw_find_station(struct ipw_priv *priv, u8 *bssid) +{ + int i; + + for (i = 0; i < priv->num_stations; i++) + if (!memcmp(priv->stations[i], bssid, ETH_ALEN)) + return i; + + return IPW_INVALID_STATION; +} + +static void ipw_send_disassociate(struct ipw_priv *priv, int quiet) +{ + int err; + + if (!(priv->status & (STATUS_ASSOCIATING | STATUS_ASSOCIATED))) { + IPW_DEBUG_ASSOC("Disassociating while not associated.\n"); + return; + } + + IPW_DEBUG_ASSOC("Disassocation attempt from " MAC_FMT " " + "on channel %d.\n", + MAC_ARG(priv->assoc_request.bssid), + priv->assoc_request.channel); + + priv->status &= ~(STATUS_ASSOCIATING | STATUS_ASSOCIATED); + priv->status |= STATUS_DISASSOCIATING; + + if (quiet) + priv->assoc_request.assoc_type = HC_DISASSOC_QUIET; + else + priv->assoc_request.assoc_type = HC_DISASSOCIATE; + err = ipw_send_associate(priv, &priv->assoc_request); + if (err) { + IPW_DEBUG_HC("Attempt to send [dis]associate command " + "failed.\n"); + return; + } + +} + +static void ipw_disassociate(void *data) +{ + ipw_send_disassociate(data, 0); +} + +static void notify_wx_assoc_event(struct ipw_priv *priv) +{ + union iwreq_data wrqu; + wrqu.ap_addr.sa_family = ARPHRD_ETHER; + if (priv->status & STATUS_ASSOCIATED) + memcpy(wrqu.ap_addr.sa_data, priv->bssid, ETH_ALEN); + else + memset(wrqu.ap_addr.sa_data, 0, ETH_ALEN); + wireless_send_event(priv->net_dev, SIOCGIWAP, &wrqu, NULL); +} + +struct ipw_status_code { + u16 status; + const char *reason; +}; + +static const struct ipw_status_code ipw_status_codes[] = { + {0x00, "Successful"}, + {0x01, "Unspecified failure"}, + {0x0A, "Cannot support all requested capabilities in the " + "Capability information field"}, + {0x0B, "Reassociation denied due to inability to confirm that " + "association exists"}, + {0x0C, "Association denied due to reason outside the scope of this " + "standard"}, + {0x0D, "Responding station does not support the specified authentication " + "algorithm"}, + {0x0E, "Received an Authentication frame with authentication sequence " + "transaction sequence number out of expected sequence"}, + {0x0F, "Authentication rejected because of challenge failure"}, + {0x10, "Authentication rejected due to timeout waiting for next " + "frame in sequence"}, + {0x11, "Association denied because AP is unable to handle additional " + "associated stations"}, + {0x12, "Association denied due to requesting station not supporting all " + "of the datarates in the BSSBasicServiceSet Parameter"}, + {0x13, "Association denied due to requesting station not supporting " + "short preamble operation"}, + {0x14, "Association denied due to requesting station not supporting " + "PBCC encoding"}, + {0x15, "Association denied due to requesting station not supporting " + "channel agility"}, + {0x19, "Association denied due to requesting station not supporting " + "short slot operation"}, + {0x1A, "Association denied due to requesting station not supporting " + "DSSS-OFDM operation"}, + {0x28, "Invalid Information Element"}, + {0x29, "Group Cipher is not valid"}, + {0x2A, "Pairwise Cipher is not valid"}, + {0x2B, "AKMP is not valid"}, + {0x2C, "Unsupported RSN IE version"}, + {0x2D, "Invalid RSN IE Capabilities"}, + {0x2E, "Cipher suite is rejected per security policy"}, +}; + +#ifdef CONFIG_IPW_DEBUG +static const char *ipw_get_status_code(u16 status) +{ + int i; + for (i = 0; i < ARRAY_SIZE(ipw_status_codes); i++) + if (ipw_status_codes[i].status == status) + return ipw_status_codes[i].reason; + return "Unknown status value."; +} +#endif + +static void inline average_init(struct average *avg) +{ + memset(avg, 0, sizeof(*avg)); +} + +static void inline average_add(struct average *avg, s16 val) +{ + avg->sum -= avg->entries[avg->pos]; + avg->sum += val; + avg->entries[avg->pos++] = val; + if (unlikely(avg->pos == AVG_ENTRIES)) { + avg->init = 1; + avg->pos = 0; + } +} + +static s16 inline average_value(struct average *avg) +{ + if (!unlikely(avg->init)) { + if (avg->pos) + return avg->sum / avg->pos; + return 0; + } + + return avg->sum / AVG_ENTRIES; +} + +static void ipw_reset_stats(struct ipw_priv *priv) +{ + u32 len = sizeof(u32); + + priv->quality = 0; + + average_init(&priv->average_missed_beacons); + average_init(&priv->average_rssi); + average_init(&priv->average_noise); + + priv->last_rate = 0; + priv->last_missed_beacons = 0; + priv->last_rx_packets = 0; + priv->last_tx_packets = 0; + priv->last_tx_failures = 0; + + /* Firmware managed, reset only when NIC is restarted, so we have to + * normalize on the current value */ + ipw_get_ordinal(priv, IPW_ORD_STAT_RX_ERR_CRC, + &priv->last_rx_err, &len); + ipw_get_ordinal(priv, IPW_ORD_STAT_TX_FAILURE, + &priv->last_tx_failures, &len); + + /* Driver managed, reset with each association */ + priv->missed_adhoc_beacons = 0; + priv->missed_beacons = 0; + priv->tx_packets = 0; + priv->rx_packets = 0; + +} + + +static inline u32 ipw_get_max_rate(struct ipw_priv *priv) +{ + u32 i = 0x80000000; + u32 mask = priv->rates_mask; + /* If currently associated in B mode, restrict the maximum + * rate match to B rates */ + if (priv->assoc_request.ieee_mode == IPW_B_MODE) + mask &= IEEE80211_CCK_RATES_MASK; + + /* TODO: Verify that the rate is supported by the current rates + * list. */ + + while (i && !(mask & i)) i >>= 1; + switch (i) { + case IEEE80211_CCK_RATE_1MB_MASK: return 1000000; + case IEEE80211_CCK_RATE_2MB_MASK: return 2000000; + case IEEE80211_CCK_RATE_5MB_MASK: return 5500000; + case IEEE80211_OFDM_RATE_6MB_MASK: return 6000000; + case IEEE80211_OFDM_RATE_9MB_MASK: return 9000000; + case IEEE80211_CCK_RATE_11MB_MASK: return 11000000; + case IEEE80211_OFDM_RATE_12MB_MASK: return 12000000; + case IEEE80211_OFDM_RATE_18MB_MASK: return 18000000; + case IEEE80211_OFDM_RATE_24MB_MASK: return 24000000; + case IEEE80211_OFDM_RATE_36MB_MASK: return 36000000; + case IEEE80211_OFDM_RATE_48MB_MASK: return 48000000; + case IEEE80211_OFDM_RATE_54MB_MASK: return 54000000; + } + + if (priv->ieee->mode == IEEE_B) + return 11000000; + else + return 54000000; +} + +static u32 ipw_get_current_rate(struct ipw_priv *priv) +{ + u32 rate, len = sizeof(rate); + int err; + + if (!(priv->status & STATUS_ASSOCIATED)) + return 0; + + if (priv->tx_packets > IPW_REAL_RATE_RX_PACKET_THRESHOLD) { + err = ipw_get_ordinal(priv, IPW_ORD_STAT_TX_CURR_RATE, &rate, + &len); + if (err) { + IPW_DEBUG_INFO("failed querying ordinals.\n"); + return 0; + } + } else + return ipw_get_max_rate(priv); + + switch (rate) { + case IPW_TX_RATE_1MB: return 1000000; + case IPW_TX_RATE_2MB: return 2000000; + case IPW_TX_RATE_5MB: return 5500000; + case IPW_TX_RATE_6MB: return 6000000; + case IPW_TX_RATE_9MB: return 9000000; + case IPW_TX_RATE_11MB: return 11000000; + case IPW_TX_RATE_12MB: return 12000000; + case IPW_TX_RATE_18MB: return 18000000; + case IPW_TX_RATE_24MB: return 24000000; + case IPW_TX_RATE_36MB: return 36000000; + case IPW_TX_RATE_48MB: return 48000000; + case IPW_TX_RATE_54MB: return 54000000; + } + + return 0; +} + +#define PERFECT_RSSI (-50) +#define WORST_RSSI (-85) +#define IPW_STATS_INTERVAL (2 * HZ) +static void ipw_gather_stats(struct ipw_priv *priv) +{ + u32 rx_err, rx_err_delta, rx_packets_delta; + u32 tx_failures, tx_failures_delta, tx_packets_delta; + u32 missed_beacons_percent, missed_beacons_delta; + u32 quality = 0; + u32 len = sizeof(u32); + s16 rssi; + u32 beacon_quality, signal_quality, tx_quality, rx_quality, + rate_quality; + + if (!(priv->status & STATUS_ASSOCIATED)) { + priv->quality = 0; + return; + } + + /* Update the statistics */ + ipw_get_ordinal(priv, IPW_ORD_STAT_MISSED_BEACONS, + &priv->missed_beacons, &len); + missed_beacons_delta = priv->missed_beacons - + priv->last_missed_beacons; + priv->last_missed_beacons = priv->missed_beacons; + if (priv->assoc_request.beacon_interval) { + missed_beacons_percent = missed_beacons_delta * + (HZ * priv->assoc_request.beacon_interval) / + (IPW_STATS_INTERVAL * 10); + } else { + missed_beacons_percent = 0; + } + average_add(&priv->average_missed_beacons, missed_beacons_percent); + + ipw_get_ordinal(priv, IPW_ORD_STAT_RX_ERR_CRC, &rx_err, &len); + rx_err_delta = rx_err - priv->last_rx_err; + priv->last_rx_err = rx_err; + + ipw_get_ordinal(priv, IPW_ORD_STAT_TX_FAILURE, &tx_failures, &len); + tx_failures_delta = tx_failures - priv->last_tx_failures; + priv->last_tx_failures = tx_failures; + + rx_packets_delta = priv->rx_packets - priv->last_rx_packets; + priv->last_rx_packets = priv->rx_packets; + + tx_packets_delta = priv->tx_packets - priv->last_tx_packets; + priv->last_tx_packets = priv->tx_packets; + + /* Calculate quality based on the following: + * + * Missed beacon: 100% = 0, 0% = 70% missed + * Rate: 60% = 1Mbs, 100% = Max + * Rx and Tx errors represent a straight % of total Rx/Tx + * RSSI: 100% = > -50, 0% = < -80 + * Rx errors: 100% = 0, 0% = 50% missed + * + * The lowest computed quality is used. + * + */ +#define BEACON_THRESHOLD 5 + beacon_quality = 100 - missed_beacons_percent; + if (beacon_quality < BEACON_THRESHOLD) + beacon_quality = 0; + else + beacon_quality = (beacon_quality - BEACON_THRESHOLD) * 100 / + (100 - BEACON_THRESHOLD); + IPW_DEBUG_STATS("Missed beacon: %3d%% (%d%%)\n", + beacon_quality, missed_beacons_percent); + + priv->last_rate = ipw_get_current_rate(priv); + rate_quality = priv->last_rate * 40 / priv->last_rate + 60; + IPW_DEBUG_STATS("Rate quality : %3d%% (%dMbs)\n", + rate_quality, priv->last_rate / 1000000); + + if (rx_packets_delta > 100 && + rx_packets_delta + rx_err_delta) + rx_quality = 100 - (rx_err_delta * 100) / + (rx_packets_delta + rx_err_delta); + else + rx_quality = 100; + IPW_DEBUG_STATS("Rx quality : %3d%% (%u errors, %u packets)\n", + rx_quality, rx_err_delta, rx_packets_delta); + + if (tx_packets_delta > 100 && + tx_packets_delta + tx_failures_delta) + tx_quality = 100 - (tx_failures_delta * 100) / + (tx_packets_delta + tx_failures_delta); + else + tx_quality = 100; + IPW_DEBUG_STATS("Tx quality : %3d%% (%u errors, %u packets)\n", + tx_quality, tx_failures_delta, tx_packets_delta); + + rssi = average_value(&priv->average_rssi); + if (rssi > PERFECT_RSSI) + signal_quality = 100; + else if (rssi < WORST_RSSI) + signal_quality = 0; + else + signal_quality = (rssi - WORST_RSSI) * 100 / + (PERFECT_RSSI - WORST_RSSI); + IPW_DEBUG_STATS("Signal level : %3d%% (%d dBm)\n", + signal_quality, rssi); + + quality = min(beacon_quality, + min(rate_quality, + min(tx_quality, min(rx_quality, signal_quality)))); + if (quality == beacon_quality) + IPW_DEBUG_STATS( + "Quality (%d%%): Clamped to missed beacons.\n", + quality); + if (quality == rate_quality) + IPW_DEBUG_STATS( + "Quality (%d%%): Clamped to rate quality.\n", + quality); + if (quality == tx_quality) + IPW_DEBUG_STATS( + "Quality (%d%%): Clamped to Tx quality.\n", + quality); + if (quality == rx_quality) + IPW_DEBUG_STATS( + "Quality (%d%%): Clamped to Rx quality.\n", + quality); + if (quality == signal_quality) + IPW_DEBUG_STATS( + "Quality (%d%%): Clamped to signal quality.\n", + quality); + + priv->quality = quality; + + queue_delayed_work(priv->workqueue, &priv->gather_stats, + IPW_STATS_INTERVAL); +} + +/** + * Handle host notification packet. + * Called from interrupt routine + */ +static inline void ipw_rx_notification(struct ipw_priv* priv, + struct ipw_rx_notification *notif) +{ + IPW_DEBUG_NOTIF("type = %i (%d bytes)\n", + notif->subtype, notif->size); + + switch (notif->subtype) { + case HOST_NOTIFICATION_STATUS_ASSOCIATED: { + struct notif_association *assoc = ¬if->u.assoc; + + switch (assoc->state) { + case CMAS_ASSOCIATED: { + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "associated: '%s' " MAC_FMT " \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + + switch (priv->ieee->iw_mode) { + case IW_MODE_INFRA: + memcpy(priv->ieee->bssid, priv->bssid, + ETH_ALEN); + break; + + case IW_MODE_ADHOC: + memcpy(priv->ieee->bssid, priv->bssid, + ETH_ALEN); + + /* clear out the station table */ + priv->num_stations = 0; + + IPW_DEBUG_ASSOC("queueing adhoc check\n"); + queue_delayed_work(priv->workqueue, + &priv->adhoc_check, + priv->assoc_request.beacon_interval); + break; + } + + priv->status &= ~STATUS_ASSOCIATING; + priv->status |= STATUS_ASSOCIATED; + + netif_carrier_on(priv->net_dev); + if (netif_queue_stopped(priv->net_dev)) { + IPW_DEBUG_NOTIF("waking queue\n"); + netif_wake_queue(priv->net_dev); + } else { + IPW_DEBUG_NOTIF("starting queue\n"); + netif_start_queue(priv->net_dev); + } + + ipw_reset_stats(priv); + /* Ensure the rate is updated immediately */ + priv->last_rate = ipw_get_current_rate(priv); + schedule_work(&priv->gather_stats); + notify_wx_assoc_event(priv); + +/* queue_delayed_work(priv->workqueue, + &priv->request_scan, + SCAN_ASSOCIATED_INTERVAL); +*/ + break; + } + + case CMAS_AUTHENTICATED: { + if (priv->status & (STATUS_ASSOCIATED | STATUS_AUTH)) { +#ifdef CONFIG_IPW_DEBUG + struct notif_authenticate *auth = ¬if->u.auth; + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "deauthenticated: '%s' " MAC_FMT ": (0x%04X) - %s \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid), + ntohs(auth->status), + ipw_get_status_code(ntohs(auth->status))); +#endif + + priv->status &= ~(STATUS_ASSOCIATING | + STATUS_AUTH | + STATUS_ASSOCIATED); + + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); + queue_work(priv->workqueue, &priv->request_scan); + notify_wx_assoc_event(priv); + break; + } + + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "authenticated: '%s' " MAC_FMT "\n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + break; + } + + case CMAS_INIT: { + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "disassociated: '%s' " MAC_FMT " \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + + priv->status &= ~( + STATUS_DISASSOCIATING | + STATUS_ASSOCIATING | + STATUS_ASSOCIATED | + STATUS_AUTH); + + netif_stop_queue(priv->net_dev); + if (!(priv->status & STATUS_ROAMING)) { + netif_carrier_off(priv->net_dev); + notify_wx_assoc_event(priv); + + /* Cancel any queued work ... */ + cancel_delayed_work(&priv->request_scan); + cancel_delayed_work(&priv->adhoc_check); + + /* Queue up another scan... */ + queue_work(priv->workqueue, + &priv->request_scan); + + cancel_delayed_work(&priv->gather_stats); + } else { + priv->status |= STATUS_ROAMING; + queue_work(priv->workqueue, + &priv->request_scan); + } + + ipw_reset_stats(priv); + break; + } + + default: + IPW_ERROR("assoc: unknown (%d)\n", + assoc->state); + break; + } + + break; + } + + case HOST_NOTIFICATION_STATUS_AUTHENTICATE: { + struct notif_authenticate *auth = ¬if->u.auth; + switch (auth->state) { + case CMAS_AUTHENTICATED: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE, + "authenticated: '%s' " MAC_FMT " \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + priv->status |= STATUS_AUTH; + break; + + case CMAS_INIT: + if (priv->status & STATUS_AUTH) { + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "authentication failed (0x%04X): %s\n", + ntohs(auth->status), + ipw_get_status_code(ntohs(auth->status))); + } + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "deauthenticated: '%s' " MAC_FMT "\n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + + priv->status &= ~(STATUS_ASSOCIATING | + STATUS_AUTH | + STATUS_ASSOCIATED); + + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); + queue_work(priv->workqueue, &priv->request_scan); + notify_wx_assoc_event(priv); + break; + + case CMAS_TX_AUTH_SEQ_1: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUTH_SEQ_1\n"); + break; + case CMAS_RX_AUTH_SEQ_2: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUTH_SEQ_2\n"); + break; + case CMAS_AUTH_SEQ_1_PASS: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUTH_SEQ_1_PASS\n"); + break; + case CMAS_AUTH_SEQ_1_FAIL: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUTH_SEQ_1_FAIL\n"); + break; + case CMAS_TX_AUTH_SEQ_3: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUTH_SEQ_3\n"); + break; + case CMAS_RX_AUTH_SEQ_4: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "RX_AUTH_SEQ_4\n"); + break; + case CMAS_AUTH_SEQ_2_PASS: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUTH_SEQ_2_PASS\n"); + break; + case CMAS_AUTH_SEQ_2_FAIL: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "AUT_SEQ_2_FAIL\n"); + break; + case CMAS_TX_ASSOC: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "TX_ASSOC\n"); + break; + case CMAS_RX_ASSOC_RESP: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "RX_ASSOC_RESP\n"); + break; + case CMAS_ASSOCIATED: + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE | IPW_DL_ASSOC, + "ASSOCIATED\n"); + break; + default: + IPW_DEBUG_NOTIF("auth: failure - %d\n", auth->state); + break; + } + break; + } + + case HOST_NOTIFICATION_STATUS_SCAN_CHANNEL_RESULT: { + struct notif_channel_result *x = ¬if->u.channel_result; + + if (notif->size == sizeof(*x)) { + IPW_DEBUG_SCAN("Scan result for channel %d\n", + x->channel_num); + } else { + IPW_DEBUG_SCAN("Scan result of wrong size %d " + "(should be %d)\n", + notif->size,sizeof(*x)); + } + break; + } + + case HOST_NOTIFICATION_STATUS_SCAN_COMPLETED: { + struct notif_scan_complete* x = ¬if->u.scan_complete; + if (notif->size == sizeof(*x)) { + IPW_DEBUG_SCAN("Scan completed: type %d, %d channels, " + "%d status\n", + x->scan_type, + x->num_channels, + x->status); + } else { + IPW_ERROR("Scan completed of wrong size %d " + "(should be %d)\n", + notif->size,sizeof(*x)); + } + + priv->status &= ~(STATUS_SCANNING | STATUS_SCAN_ABORTING); + + cancel_delayed_work(&priv->scan_check); + + if (!(priv->status & (STATUS_ASSOCIATED | + STATUS_ASSOCIATING | + STATUS_ROAMING | + STATUS_DISASSOCIATING))) + queue_work(priv->workqueue, &priv->associate); + else if (priv->status & STATUS_ROAMING) { + /* If a scan completed and we are in roam mode, then + * the scan that completed was the one requested as a + * result of entering roam... so, schedule the + * roam work */ + queue_work(priv->workqueue, &priv->roam); + } else if (priv->status & STATUS_SCAN_PENDING) + queue_work(priv->workqueue, &priv->request_scan); + + priv->ieee->scans++; + break; + } + + case HOST_NOTIFICATION_STATUS_FRAG_LENGTH: { + struct notif_frag_length *x = ¬if->u.frag_len; + + if (notif->size == sizeof(*x)) { + IPW_ERROR("Frag length: %d\n", x->frag_length); + } else { + IPW_ERROR("Frag length of wrong size %d " + "(should be %d)\n", + notif->size, sizeof(*x)); + } + break; + } + + case HOST_NOTIFICATION_STATUS_LINK_DETERIORATION: { + struct notif_link_deterioration *x = + ¬if->u.link_deterioration; + if (notif->size==sizeof(*x)) { + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE, + "link deterioration: '%s' " MAC_FMT " \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + memcpy(&priv->last_link_deterioration, x, sizeof(*x)); + } else { + IPW_ERROR("Link Deterioration of wrong size %d " + "(should be %d)\n", + notif->size,sizeof(*x)); + } + break; + } + + case HOST_NOTIFICATION_DINO_CONFIG_RESPONSE: { + IPW_ERROR("Dino config\n"); + if (priv->hcmd && priv->hcmd->cmd == HOST_CMD_DINO_CONFIG) { + /* TODO: Do anything special? */ + } else { + IPW_ERROR("Unexpected DINO_CONFIG_RESPONSE\n"); + } + break; + } + + case HOST_NOTIFICATION_STATUS_BEACON_STATE: { + struct notif_beacon_state *x = ¬if->u.beacon_state; + if (notif->size != sizeof(*x)) { + IPW_ERROR("Beacon state of wrong size %d (should " + "be %d)\n", notif->size, sizeof(*x)); + break; + } + + if (x->state == HOST_NOTIFICATION_STATUS_BEACON_MISSING) { + if (priv->status & STATUS_SCANNING) { + /* Stop scan to keep fw from getting + * stuck... */ + queue_work(priv->workqueue, + &priv->abort_scan); + } + + if (x->number > priv->missed_beacon_threshold && + priv->status & STATUS_ASSOCIATED) { + IPW_DEBUG(IPW_DL_INFO | IPW_DL_NOTIF | + IPW_DL_STATE, + "Missed beacon: %d - disassociate\n", + x->number); + queue_work(priv->workqueue, + &priv->disassociate); + } else if (x->number > priv->roaming_threshold) { + IPW_DEBUG(IPW_DL_NOTIF | IPW_DL_STATE, + "Missed beacon: %d - initiate " + "roaming\n", + x->number); + queue_work(priv->workqueue, + &priv->roam); + } else { + IPW_DEBUG_NOTIF("Missed beacon: %d\n", + x->number); + } + + priv->notif_missed_beacons = x->number; + + } + + + break; + } + + case HOST_NOTIFICATION_STATUS_TGI_TX_KEY: { + struct notif_tgi_tx_key *x = ¬if->u.tgi_tx_key; + if (notif->size==sizeof(*x)) { + IPW_ERROR("TGi Tx Key: state 0x%02x sec type " + "0x%02x station %d\n", + x->key_state,x->security_type, + x->station_index); + break; + } + + IPW_ERROR("TGi Tx Key of wrong size %d (should be %d)\n", + notif->size,sizeof(*x)); + break; + } + + case HOST_NOTIFICATION_CALIB_KEEP_RESULTS: { + struct notif_calibration *x = ¬if->u.calibration; + + if (notif->size == sizeof(*x)) { + memcpy(&priv->calib, x, sizeof(*x)); + IPW_DEBUG_INFO("TODO: Calibration\n"); + break; + } + + IPW_ERROR("Calibration of wrong size %d (should be %d)\n", + notif->size,sizeof(*x)); + break; + } + + case HOST_NOTIFICATION_NOISE_STATS: { + if (notif->size == sizeof(u32)) { + priv->last_noise = (u8)(notif->u.noise.value & 0xff); + average_add(&priv->average_noise, priv->last_noise); + break; + } + + IPW_ERROR("Noise stat is wrong size %d (should be %d)\n", + notif->size, sizeof(u32)); + break; + } + + default: + IPW_ERROR("Unknown notification: " + "subtype=%d,flags=0x%2x,size=%d\n", + notif->subtype, notif->flags, notif->size); + } +} + +/** + * Destroys all DMA structures and initialise them again + * + * @param priv + * @return error code + */ +static int ipw_queue_reset(struct ipw_priv *priv) +{ + int rc = 0; + /** @todo customize queue sizes */ + int nTx = 64, nTxCmd = 8; + ipw_tx_queue_free(priv); + /* Tx CMD queue */ + rc = ipw_queue_tx_init(priv, &priv->txq_cmd, nTxCmd, + CX2_TX_CMD_QUEUE_READ_INDEX, + CX2_TX_CMD_QUEUE_WRITE_INDEX, + CX2_TX_CMD_QUEUE_BD_BASE, + CX2_TX_CMD_QUEUE_BD_SIZE); + if (rc) { + IPW_ERROR("Tx Cmd queue init failed\n"); + goto error; + } + /* Tx queue(s) */ + rc = ipw_queue_tx_init(priv, &priv->txq[0], nTx, + CX2_TX_QUEUE_0_READ_INDEX, + CX2_TX_QUEUE_0_WRITE_INDEX, + CX2_TX_QUEUE_0_BD_BASE, + CX2_TX_QUEUE_0_BD_SIZE); + if (rc) { + IPW_ERROR("Tx 0 queue init failed\n"); + goto error; + } + rc = ipw_queue_tx_init(priv, &priv->txq[1], nTx, + CX2_TX_QUEUE_1_READ_INDEX, + CX2_TX_QUEUE_1_WRITE_INDEX, + CX2_TX_QUEUE_1_BD_BASE, + CX2_TX_QUEUE_1_BD_SIZE); + if (rc) { + IPW_ERROR("Tx 1 queue init failed\n"); + goto error; + } + rc = ipw_queue_tx_init(priv, &priv->txq[2], nTx, + CX2_TX_QUEUE_2_READ_INDEX, + CX2_TX_QUEUE_2_WRITE_INDEX, + CX2_TX_QUEUE_2_BD_BASE, + CX2_TX_QUEUE_2_BD_SIZE); + if (rc) { + IPW_ERROR("Tx 2 queue init failed\n"); + goto error; + } + rc = ipw_queue_tx_init(priv, &priv->txq[3], nTx, + CX2_TX_QUEUE_3_READ_INDEX, + CX2_TX_QUEUE_3_WRITE_INDEX, + CX2_TX_QUEUE_3_BD_BASE, + CX2_TX_QUEUE_3_BD_SIZE); + if (rc) { + IPW_ERROR("Tx 3 queue init failed\n"); + goto error; + } + /* statistics */ + priv->rx_bufs_min = 0; + priv->rx_pend_max = 0; + return rc; + + error: + ipw_tx_queue_free(priv); + return rc; +} + +/** + * Reclaim Tx queue entries no more used by NIC. + * + * When FW adwances 'R' index, all entries between old and + * new 'R' index need to be reclaimed. As result, some free space + * forms. If there is enough free space (> low mark), wake Tx queue. + * + * @note Need to protect against garbage in 'R' index + * @param priv + * @param txq + * @param qindex + * @return Number of used entries remains in the queue + */ +static int ipw_queue_tx_reclaim(struct ipw_priv *priv, + struct clx2_tx_queue *txq, int qindex) +{ + u32 hw_tail; + int used; + struct clx2_queue *q = &txq->q; + + hw_tail = ipw_read32(priv, q->reg_r); + if (hw_tail >= q->n_bd) { + IPW_ERROR + ("Read index for DMA queue (%d) is out of range [0-%d)\n", + hw_tail, q->n_bd); + goto done; + } + for (; q->last_used != hw_tail; + q->last_used = ipw_queue_inc_wrap(q->last_used, q->n_bd)) { + ipw_queue_tx_free_tfd(priv, txq); + priv->tx_packets++; + } + done: + if (ipw_queue_space(q) > q->low_mark && qindex >= 0) { + __maybe_wake_tx(priv); + } + used = q->first_empty - q->last_used; + if (used < 0) + used += q->n_bd; + + return used; +} + +static int ipw_queue_tx_hcmd(struct ipw_priv *priv, int hcmd, void *buf, + int len, int sync) +{ + struct clx2_tx_queue *txq = &priv->txq_cmd; + struct clx2_queue *q = &txq->q; + struct tfd_frame *tfd; + + if (ipw_queue_space(q) < (sync ? 1 : 2)) { + IPW_ERROR("No space for Tx\n"); + return -EBUSY; + } + + tfd = &txq->bd[q->first_empty]; + txq->txb[q->first_empty] = NULL; + + memset(tfd, 0, sizeof(*tfd)); + tfd->control_flags.message_type = TX_HOST_COMMAND_TYPE; + tfd->control_flags.control_bits = TFD_NEED_IRQ_MASK; + priv->hcmd_seq++; + tfd->u.cmd.index = hcmd; + tfd->u.cmd.length = len; + memcpy(tfd->u.cmd.payload, buf, len); + q->first_empty = ipw_queue_inc_wrap(q->first_empty, q->n_bd); + ipw_write32(priv, q->reg_w, q->first_empty); + _ipw_read32(priv, 0x90); + + return 0; +} + + + +/* + * Rx theory of operation + * + * The host allocates 32 DMA target addresses and passes the host address + * to the firmware at register CX2_RFDS_TABLE_LOWER + N * RFD_SIZE where N is + * 0 to 31 + * + * Rx Queue Indexes + * The host/firmware share two index registers for managing the Rx buffers. + * + * The READ index maps to the first position that the firmware may be writing + * to -- the driver can read up to (but not including) this position and get + * good data. + * The READ index is managed by the firmware once the card is enabled. + * + * The WRITE index maps to the last position the driver has read from -- the + * position preceding WRITE is the last slot the firmware can place a packet. + * + * The queue is empty (no good data) if WRITE = READ - 1, and is full if + * WRITE = READ. + * + * During initialization the host sets up the READ queue position to the first + * INDEX position, and WRITE to the last (READ - 1 wrapped) + * + * When the firmware places a packet in a buffer it will advance the READ index + * and fire the RX interrupt. The driver can then query the READ index and + * process as many packets as possible, moving the WRITE index forward as it + * resets the Rx queue buffers with new memory. + * + * The management in the driver is as follows: + * + A list of pre-allocated SKBs is stored in ipw->rxq->rx_free. When + * ipw->rxq->free_count drops to or below RX_LOW_WATERMARK, work is scheduled + * to replensish the ipw->rxq->rx_free. + * + In ipw_rx_queue_replenish (scheduled) if 'processed' != 'read' then the + * ipw->rxq is replenished and the READ INDEX is updated (updating the + * 'processed' and 'read' driver indexes as well) + * + A received packet is processed and handed to the kernel network stack, + * detached from the ipw->rxq. The driver 'processed' index is updated. + * + The Host/Firmware ipw->rxq is replenished at tasklet time from the rx_free + * list. If there are no allocated buffers in ipw->rxq->rx_free, the READ + * INDEX is not incremented and ipw->status(RX_STALLED) is set. If there + * were enough free buffers and RX_STALLED is set it is cleared. + * + * + * Driver sequence: + * + * ipw_rx_queue_alloc() Allocates rx_free + * ipw_rx_queue_replenish() Replenishes rx_free list from rx_used, and calls + * ipw_rx_queue_restock + * ipw_rx_queue_restock() Moves available buffers from rx_free into Rx + * queue, updates firmware pointers, and updates + * the WRITE index. If insufficient rx_free buffers + * are available, schedules ipw_rx_queue_replenish + * + * -- enable interrupts -- + * ISR - ipw_rx() Detach ipw_rx_mem_buffers from pool up to the + * READ INDEX, detaching the SKB from the pool. + * Moves the packet buffer from queue to rx_used. + * Calls ipw_rx_queue_restock to refill any empty + * slots. + * ... + * + */ + +/* + * If there are slots in the RX queue that need to be restocked, + * and we have free pre-allocated buffers, fill the ranks as much + * as we can pulling from rx_free. + * + * This moves the 'write' index forward to catch up with 'processed', and + * also updates the memory address in the firmware to reference the new + * target buffer. + */ +static void ipw_rx_queue_restock(struct ipw_priv *priv) +{ + struct ipw_rx_queue *rxq = priv->rxq; + struct list_head *element; + struct ipw_rx_mem_buffer *rxb; + unsigned long flags; + int write; + + spin_lock_irqsave(&rxq->lock, flags); + write = rxq->write; + while ((rxq->write != rxq->processed) && (rxq->free_count)) { + element = rxq->rx_free.next; + rxb = list_entry(element, struct ipw_rx_mem_buffer, list); + list_del(element); + + ipw_write32(priv, CX2_RFDS_TABLE_LOWER + rxq->write * RFD_SIZE, + rxb->dma_addr); + rxq->queue[rxq->write] = rxb; + rxq->write = (rxq->write + 1) % RX_QUEUE_SIZE; + rxq->free_count--; + } + spin_unlock_irqrestore(&rxq->lock, flags); + + /* If the pre-allocated buffer pool is dropping low, schedule to + * refill it */ + if (rxq->free_count <= RX_LOW_WATERMARK) + queue_work(priv->workqueue, &priv->rx_replenish); + + /* If we've added more space for the firmware to place data, tell it */ + if (write != rxq->write) + ipw_write32(priv, CX2_RX_WRITE_INDEX, rxq->write); +} + +/* + * Move all used packet from rx_used to rx_free, allocating a new SKB for each. + * Also restock the Rx queue via ipw_rx_queue_restock. + * + * This is called as a scheduled work item (except for during intialization) + */ +static void ipw_rx_queue_replenish(void *data) +{ + struct ipw_priv *priv = data; + struct ipw_rx_queue *rxq = priv->rxq; + struct list_head *element; + struct ipw_rx_mem_buffer *rxb; + unsigned long flags; + + spin_lock_irqsave(&rxq->lock, flags); + while (!list_empty(&rxq->rx_used)) { + element = rxq->rx_used.next; + rxb = list_entry(element, struct ipw_rx_mem_buffer, list); + rxb->skb = alloc_skb(CX2_RX_BUF_SIZE, GFP_ATOMIC); + if (!rxb->skb) { + printk(KERN_CRIT "%s: Can not allocate SKB buffers.\n", + priv->net_dev->name); + /* We don't reschedule replenish work here -- we will + * call the restock method and if it still needs + * more buffers it will schedule replenish */ + break; + } + list_del(element); + + rxb->rxb = (struct ipw_rx_buffer *)rxb->skb->data; + rxb->dma_addr = pci_map_single( + priv->pci_dev, rxb->skb->data, CX2_RX_BUF_SIZE, + PCI_DMA_FROMDEVICE); + + list_add_tail(&rxb->list, &rxq->rx_free); + rxq->free_count++; + } + spin_unlock_irqrestore(&rxq->lock, flags); + + ipw_rx_queue_restock(priv); +} + +/* Assumes that the skb field of the buffers in 'pool' is kept accurate. + * If an SKB has been detached, the POOL needs to have it's SKB set to NULL + * This free routine walks the list of POOL entries and if SKB is set to + * non NULL it is unmapped and freed + */ +static void ipw_rx_queue_free(struct ipw_priv *priv, + struct ipw_rx_queue *rxq) +{ + int i; + + if (!rxq) + return; + + for (i = 0; i < RX_QUEUE_SIZE + RX_FREE_BUFFERS; i++) { + if (rxq->pool[i].skb != NULL) { + pci_unmap_single(priv->pci_dev, rxq->pool[i].dma_addr, + CX2_RX_BUF_SIZE, + PCI_DMA_FROMDEVICE); + dev_kfree_skb(rxq->pool[i].skb); + } + } + + kfree(rxq); +} + +static struct ipw_rx_queue *ipw_rx_queue_alloc(struct ipw_priv *priv) +{ + struct ipw_rx_queue *rxq; + int i; + + rxq = (struct ipw_rx_queue *)kmalloc(sizeof(*rxq), GFP_KERNEL); + memset(rxq, 0, sizeof(*rxq)); + spin_lock_init(&rxq->lock); + INIT_LIST_HEAD(&rxq->rx_free); + INIT_LIST_HEAD(&rxq->rx_used); + + /* Fill the rx_used queue with _all_ of the Rx buffers */ + for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++) + list_add_tail(&rxq->pool[i].list, &rxq->rx_used); + + /* Set us so that we have processed and used all buffers, but have + * not restocked the Rx queue with fresh buffers */ + rxq->read = rxq->write = 0; + rxq->processed = RX_QUEUE_SIZE - 1; + rxq->free_count = 0; + + return rxq; +} + +static int ipw_is_rate_in_mask(struct ipw_priv *priv, int ieee_mode, u8 rate) +{ + rate &= ~IEEE80211_BASIC_RATE_MASK; + if (ieee_mode == IEEE_A) { + switch (rate) { + case IEEE80211_OFDM_RATE_6MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_6MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_9MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_9MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_12MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_12MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_18MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_18MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_24MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_24MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_36MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_36MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_48MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_48MB_MASK ? + 1 : 0; + case IEEE80211_OFDM_RATE_54MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_54MB_MASK ? + 1 : 0; + default: + return 0; + } + } + + /* B and G mixed */ + switch (rate) { + case IEEE80211_CCK_RATE_1MB: + return priv->rates_mask & IEEE80211_CCK_RATE_1MB_MASK ? 1 : 0; + case IEEE80211_CCK_RATE_2MB: + return priv->rates_mask & IEEE80211_CCK_RATE_2MB_MASK ? 1 : 0; + case IEEE80211_CCK_RATE_5MB: + return priv->rates_mask & IEEE80211_CCK_RATE_5MB_MASK ? 1 : 0; + case IEEE80211_CCK_RATE_11MB: + return priv->rates_mask & IEEE80211_CCK_RATE_11MB_MASK ? 1 : 0; + } + + /* If we are limited to B modulations, bail at this point */ + if (ieee_mode == IEEE_B) + return 0; + + /* G */ + switch (rate) { + case IEEE80211_OFDM_RATE_6MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_6MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_9MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_9MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_12MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_12MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_18MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_18MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_24MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_24MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_36MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_36MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_48MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_48MB_MASK ? 1 : 0; + case IEEE80211_OFDM_RATE_54MB: + return priv->rates_mask & IEEE80211_OFDM_RATE_54MB_MASK ? 1 : 0; + } + + return 0; +} + +static int ipw_compatible_rates(struct ipw_priv *priv, + const struct ieee80211_network *network, + struct ipw_supported_rates *rates) +{ + int num_rates, i; + + memset(rates, 0, sizeof(*rates)); + num_rates = min(network->rates_len, (u8)IPW_MAX_RATES); + rates->num_rates = 0; + for (i = 0; i < num_rates; i++) { + if (!ipw_is_rate_in_mask(priv, network->mode, network->rates[i])) { + IPW_DEBUG_SCAN("Rate %02X masked : 0x%08X\n", + network->rates[i], priv->rates_mask); + continue; + } + + rates->supported_rates[rates->num_rates++] = network->rates[i]; + } + + num_rates = min(network->rates_ex_len, (u8)(IPW_MAX_RATES - num_rates)); + for (i = 0; i < num_rates; i++) { + if (!ipw_is_rate_in_mask(priv, network->mode, network->rates_ex[i])) { + IPW_DEBUG_SCAN("Rate %02X masked : 0x%08X\n", + network->rates_ex[i], priv->rates_mask); + continue; + } + + rates->supported_rates[rates->num_rates++] = network->rates_ex[i]; + } + + return rates->num_rates; +} + +static inline void ipw_copy_rates(struct ipw_supported_rates *dest, + const struct ipw_supported_rates *src) +{ + u8 i; + for (i = 0; i < src->num_rates; i++) + dest->supported_rates[i] = src->supported_rates[i]; + dest->num_rates = src->num_rates; +} + +/* TODO: Look at sniffed packets in the air to determine if the basic rate + * mask should ever be used -- right now all callers to add the scan rates are + * set with the modulation = CCK, so BASIC_RATE_MASK is never set... */ +static void ipw_add_cck_scan_rates(struct ipw_supported_rates *rates, + u8 modulation, u32 rate_mask) +{ + u8 basic_mask = (IEEE80211_OFDM_MODULATION == modulation) ? + IEEE80211_BASIC_RATE_MASK : 0; + + if (rate_mask & IEEE80211_CCK_RATE_1MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_BASIC_RATE_MASK | IEEE80211_CCK_RATE_1MB; + + if (rate_mask & IEEE80211_CCK_RATE_2MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_BASIC_RATE_MASK | IEEE80211_CCK_RATE_2MB; + + if (rate_mask & IEEE80211_CCK_RATE_5MB_MASK) + rates->supported_rates[rates->num_rates++] = basic_mask | + IEEE80211_CCK_RATE_5MB; + + if (rate_mask & IEEE80211_CCK_RATE_11MB_MASK) + rates->supported_rates[rates->num_rates++] = basic_mask | + IEEE80211_CCK_RATE_11MB; +} + +static void ipw_add_ofdm_scan_rates(struct ipw_supported_rates *rates, + u8 modulation, u32 rate_mask) +{ + u8 basic_mask = (IEEE80211_OFDM_MODULATION == modulation) ? + IEEE80211_BASIC_RATE_MASK : 0; + + if (rate_mask & IEEE80211_OFDM_RATE_6MB_MASK) + rates->supported_rates[rates->num_rates++] = basic_mask | + IEEE80211_OFDM_RATE_6MB; + + if (rate_mask & IEEE80211_OFDM_RATE_9MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_OFDM_RATE_9MB; + + if (rate_mask & IEEE80211_OFDM_RATE_12MB_MASK) + rates->supported_rates[rates->num_rates++] = basic_mask | + IEEE80211_OFDM_RATE_12MB; + + if (rate_mask & IEEE80211_OFDM_RATE_18MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_OFDM_RATE_18MB; + + if (rate_mask & IEEE80211_OFDM_RATE_24MB_MASK) + rates->supported_rates[rates->num_rates++] = basic_mask | + IEEE80211_OFDM_RATE_24MB; + + if (rate_mask & IEEE80211_OFDM_RATE_36MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_OFDM_RATE_36MB; + + if (rate_mask & IEEE80211_OFDM_RATE_48MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_OFDM_RATE_48MB; + + if (rate_mask & IEEE80211_OFDM_RATE_54MB_MASK) + rates->supported_rates[rates->num_rates++] = + IEEE80211_OFDM_RATE_54MB; +} + +struct ipw_network_match { + struct ieee80211_network *network; + struct ipw_supported_rates rates; +}; + +static int ipw_best_network( + struct ipw_priv *priv, + struct ipw_network_match *match, + struct ieee80211_network *network, + int roaming) +{ + struct ipw_supported_rates rates; + + /* Verify that this network's capability is compatible with the + * current mode (AdHoc or Infrastructure) */ + if ((priv->ieee->iw_mode == IW_MODE_INFRA && + !(network->capability & WLAN_CAPABILITY_BSS)) || + (priv->ieee->iw_mode == IW_MODE_ADHOC && + !(network->capability & WLAN_CAPABILITY_IBSS))) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded due to " + "capability mismatch.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid)); + return 0; + } + + /* If we do not have an ESSID for this AP, we can not associate with + * it */ + if (network->flags & NETWORK_EMPTY_ESSID) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of hidden ESSID.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid)); + return 0; + } + + if (unlikely(roaming)) { + /* If we are roaming, then ensure check if this is a valid + * network to try and roam to */ + if ((network->ssid_len != match->network->ssid_len) || + memcmp(network->ssid, match->network->ssid, + network->ssid_len)) { + IPW_DEBUG_ASSOC("Netowrk '%s (" MAC_FMT ")' excluded " + "because of non-network ESSID.\n", + escape_essid(network->ssid, + network->ssid_len), + MAC_ARG(network->bssid)); + return 0; + } + } else { + /* If an ESSID has been configured then compare the broadcast + * ESSID to ours */ + if ((priv->config & CFG_STATIC_ESSID) && + ((network->ssid_len != priv->essid_len) || + memcmp(network->ssid, priv->essid, + min(network->ssid_len, priv->essid_len)))) { + char escaped[IW_ESSID_MAX_SIZE * 2 + 1]; + strncpy(escaped, escape_essid( + network->ssid, network->ssid_len), + sizeof(escaped)); + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of ESSID mismatch: '%s'.\n", + escaped, MAC_ARG(network->bssid), + escape_essid(priv->essid, priv->essid_len)); + return 0; + } + } + + /* If the old network rate is better than this one, don't bother + * testing everything else. */ + if (match->network && match->network->stats.rssi > + network->stats.rssi) { + char escaped[IW_ESSID_MAX_SIZE * 2 + 1]; + strncpy(escaped, + escape_essid(network->ssid, network->ssid_len), + sizeof(escaped)); + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded because " + "'%s (" MAC_FMT ")' has a stronger signal.\n", + escaped, MAC_ARG(network->bssid), + escape_essid(match->network->ssid, + match->network->ssid_len), + MAC_ARG(match->network->bssid)); + return 0; + } + + /* If this network has already had an association attempt within the + * last 3 seconds, do not try and associate again... */ + if (network->last_associate && + time_after(network->last_associate + (HZ * 5UL), jiffies)) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of storming (%lu since last " + "assoc attempt).\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid), + (jiffies - network->last_associate) / HZ); + return 0; + } + + /* Now go through and see if the requested network is valid... */ + if (priv->ieee->scan_age != 0 && + jiffies - network->last_scanned > priv->ieee->scan_age) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of age: %lums.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid), + (jiffies - network->last_scanned) / (HZ / 100)); + return 0; + } + + if ((priv->config & CFG_STATIC_CHANNEL) && + (network->channel != priv->channel)) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of channel mismatch: %d != %d.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid), + network->channel, priv->channel); + return 0; + } + + /* Verify privacy compatability */ + if (((priv->capability & CAP_PRIVACY_ON) ? 1 : 0) != + ((network->capability & WLAN_CAPABILITY_PRIVACY) ? 1 : 0)) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of privacy mismatch: %s != %s.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid), + priv->capability & CAP_PRIVACY_ON ? "on" : + "off", + network->capability & + WLAN_CAPABILITY_PRIVACY ?"on" : "off"); + return 0; + } + + if ((priv->config & CFG_STATIC_BSSID) && + memcmp(network->bssid, priv->bssid, ETH_ALEN)) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of BSSID mismatch: " MAC_FMT ".\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid), + MAC_ARG(priv->bssid)); + return 0; + } + + /* Filter out any incompatible freq / mode combinations */ + if (!ieee80211_is_valid_mode(priv->ieee, network->mode)) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of invalid frequency/mode " + "combination.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid)); + return 0; + } + + ipw_compatible_rates(priv, network, &rates); + if (rates.num_rates == 0) { + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' excluded " + "because of no compatible rates.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid)); + return 0; + } + + /* TODO: Perform any further minimal comparititive tests. We do not + * want to put too much policy logic here; intelligent scan selection + * should occur within a generic IEEE 802.11 user space tool. */ + + /* Set up 'new' AP to this network */ + ipw_copy_rates(&match->rates, &rates); + match->network = network; + + IPW_DEBUG_ASSOC("Network '%s (" MAC_FMT ")' is a viable match.\n", + escape_essid(network->ssid, network->ssid_len), + MAC_ARG(network->bssid)); + + return 1; +} + + +static void ipw_adhoc_create(struct ipw_priv *priv, + struct ieee80211_network *network) +{ + /* + * For the purposes of scanning, we can set our wireless mode + * to trigger scans across combinations of bands, but when it + * comes to creating a new ad-hoc network, we have tell the FW + * exactly which band to use. + * + * We also have the possibility of an invalid channel for the + * chossen band. Attempting to create a new ad-hoc network + * with an invalid channel for wireless mode will trigger a + * FW fatal error. + */ + network->mode = is_valid_channel(priv->ieee->mode, priv->channel); + if (network->mode) { + network->channel = priv->channel; + } else { + IPW_WARNING("Overriding invalid channel\n"); + if (priv->ieee->mode & IEEE_A) { + network->mode = IEEE_A; + priv->channel = band_a_active_channel[0]; + } else if (priv->ieee->mode & IEEE_G) { + network->mode = IEEE_G; + priv->channel = band_b_active_channel[0]; + } else { + network->mode = IEEE_B; + priv->channel = band_b_active_channel[0]; + } + } + + network->channel = priv->channel; + priv->config |= CFG_ADHOC_PERSIST; + ipw_create_bssid(priv, network->bssid); + network->ssid_len = priv->essid_len; + memcpy(network->ssid, priv->essid, priv->essid_len); + memset(&network->stats, 0, sizeof(network->stats)); + network->capability = WLAN_CAPABILITY_IBSS; + if (priv->capability & CAP_PRIVACY_ON) + network->capability |= WLAN_CAPABILITY_PRIVACY; + network->rates_len = min(priv->rates.num_rates, MAX_RATES_LENGTH); + memcpy(network->rates, priv->rates.supported_rates, + network->rates_len); + network->rates_ex_len = priv->rates.num_rates - network->rates_len; + memcpy(network->rates_ex, + &priv->rates.supported_rates[network->rates_len], + network->rates_ex_len); + network->last_scanned = 0; + network->flags = 0; + network->last_associate = 0; + network->time_stamp[0] = 0; + network->time_stamp[1] = 0; + network->beacon_interval = 100; /* Default */ + network->listen_interval = 10; /* Default */ + network->atim_window = 0; /* Default */ +#ifdef CONFIG_IEEE80211_WPA + network->wpa_ie_len = 0; + network->rsn_ie_len = 0; +#endif /* CONFIG_IEEE80211_WPA */ +} + +static void ipw_send_wep_keys(struct ipw_priv *priv) +{ + struct ipw_wep_key *key; + int i; + struct host_cmd cmd = { + .cmd = IPW_CMD_WEP_KEY, + .len = sizeof(*key) + }; + + key = (struct ipw_wep_key *)&cmd.param; + key->cmd_id = DINO_CMD_WEP_KEY; + key->seq_num = 0; + + for (i = 0; i < 4; i++) { + key->key_index = i; + if (!(priv->sec.flags & (1 << i))) { + key->key_size = 0; + } else { + key->key_size = priv->sec.key_sizes[i]; + memcpy(key->key, priv->sec.keys[i], key->key_size); + } + + if (ipw_send_cmd(priv, &cmd)) { + IPW_ERROR("failed to send WEP_KEY command\n"); + return; + } + } +} + +static void ipw_adhoc_check(void *data) +{ + struct ipw_priv *priv = data; + + if (priv->missed_adhoc_beacons++ > priv->missed_beacon_threshold && + !(priv->config & CFG_ADHOC_PERSIST)) { + IPW_DEBUG_SCAN("Disassociating due to missed beacons\n"); + ipw_remove_current_network(priv); + ipw_disassociate(priv); + return; + } + + queue_delayed_work(priv->workqueue, &priv->adhoc_check, + priv->assoc_request.beacon_interval); +} + +#ifdef CONFIG_IPW_DEBUG +static void ipw_debug_config(struct ipw_priv *priv) +{ + IPW_DEBUG_INFO("Scan completed, no valid APs matched " + "[CFG 0x%08X]\n", priv->config); + if (priv->config & CFG_STATIC_CHANNEL) + IPW_DEBUG_INFO("Channel locked to %d\n", + priv->channel); + else + IPW_DEBUG_INFO("Channel unlocked.\n"); + if (priv->config & CFG_STATIC_ESSID) + IPW_DEBUG_INFO("ESSID locked to '%s'\n", + escape_essid(priv->essid, + priv->essid_len)); + else + IPW_DEBUG_INFO("ESSID unlocked.\n"); + if (priv->config & CFG_STATIC_BSSID) + IPW_DEBUG_INFO("BSSID locked to %d\n", priv->channel); + else + IPW_DEBUG_INFO("BSSID unlocked.\n"); + if (priv->capability & CAP_PRIVACY_ON) + IPW_DEBUG_INFO("PRIVACY on\n"); + else + IPW_DEBUG_INFO("PRIVACY off\n"); + IPW_DEBUG_INFO("RATE MASK: 0x%08X\n", priv->rates_mask); +} +#else +#define ipw_debug_config(x) do {} while (0); +#endif + +static inline void ipw_set_fixed_rate(struct ipw_priv *priv, + struct ieee80211_network *network) +{ + /* TODO: Verify that this works... */ + struct ipw_fixed_rate fr = { + .tx_rates = priv->rates_mask + }; + u32 reg; + u16 mask = 0; + + /* Identify 'current FW band' and match it with the fixed + * Tx rates */ + + switch (priv->ieee->freq_band) { + case IEEE80211_52GHZ_BAND: /* A only */ + /* IEEE_A */ + if (priv->rates_mask & ~IEEE80211_OFDM_RATES_MASK) { + /* Invalid fixed rate mask */ + fr.tx_rates = 0; + break; + } + + fr.tx_rates >>= IEEE80211_OFDM_SHIFT_MASK_A; + break; + + default: /* 2.4Ghz or Mixed */ + /* IEEE_B */ + if (network->mode == IEEE_B) { + if (fr.tx_rates & ~IEEE80211_CCK_RATES_MASK) { + /* Invalid fixed rate mask */ + fr.tx_rates = 0; + } + break; + } + + /* IEEE_G */ + if (fr.tx_rates & ~(IEEE80211_CCK_RATES_MASK | + IEEE80211_OFDM_RATES_MASK)) { + /* Invalid fixed rate mask */ + fr.tx_rates = 0; + break; + } + + if (IEEE80211_OFDM_RATE_6MB_MASK & fr.tx_rates) { + mask |= (IEEE80211_OFDM_RATE_6MB_MASK >> 1); + fr.tx_rates &= ~IEEE80211_OFDM_RATE_6MB_MASK; + } + + if (IEEE80211_OFDM_RATE_9MB_MASK & fr.tx_rates) { + mask |= (IEEE80211_OFDM_RATE_9MB_MASK >> 1); + fr.tx_rates &= ~IEEE80211_OFDM_RATE_9MB_MASK; + } + + if (IEEE80211_OFDM_RATE_12MB_MASK & fr.tx_rates) { + mask |= (IEEE80211_OFDM_RATE_12MB_MASK >> 1); + fr.tx_rates &= ~IEEE80211_OFDM_RATE_12MB_MASK; + } + + fr.tx_rates |= mask; + break; + } + + reg = ipw_read32(priv, IPW_MEM_FIXED_OVERRIDE); + ipw_write_reg32(priv, reg, *(u32*)&fr); +} + +static int ipw_associate_network(struct ipw_priv *priv, + struct ieee80211_network *network, + struct ipw_supported_rates *rates, + int roaming) +{ + int err; + + if (priv->config & CFG_FIXED_RATE) + ipw_set_fixed_rate(priv, network); + + if (!(priv->config & CFG_STATIC_ESSID)) { + priv->essid_len = min(network->ssid_len, + (u8)IW_ESSID_MAX_SIZE); + memcpy(priv->essid, network->ssid, priv->essid_len); + } + + network->last_associate = jiffies; + + memset(&priv->assoc_request, 0, sizeof(priv->assoc_request)); + priv->assoc_request.channel = network->channel; + if ((priv->capability & CAP_PRIVACY_ON) && + (priv->capability & CAP_SHARED_KEY)) { + priv->assoc_request.auth_type = AUTH_SHARED_KEY; + priv->assoc_request.auth_key = priv->sec.active_key; + } else { + priv->assoc_request.auth_type = AUTH_OPEN; + priv->assoc_request.auth_key = 0; + } + + if (priv->capability & CAP_PRIVACY_ON) + ipw_send_wep_keys(priv); + + /* + * It is valid for our ieee device to support multiple modes, but + * when it comes to associating to a given network we have to choose + * just one mode. + */ + if (network->mode & priv->ieee->mode & IEEE_A) + priv->assoc_request.ieee_mode = IPW_A_MODE; + else if (network->mode & priv->ieee->mode & IEEE_G) + priv->assoc_request.ieee_mode = IPW_G_MODE; + else if (network->mode & priv->ieee->mode & IEEE_B) + priv->assoc_request.ieee_mode = IPW_B_MODE; + + IPW_DEBUG_ASSOC("%sssocation attempt: '%s', channel %d, " + "802.11%c [%d], enc=%s%s%s%c%c\n", + roaming ? "Rea" : "A", + escape_essid(priv->essid, priv->essid_len), + network->channel, + ipw_modes[priv->assoc_request.ieee_mode], + rates->num_rates, + priv->capability & CAP_PRIVACY_ON ? "on " : "off", + priv->capability & CAP_PRIVACY_ON ? + (priv->capability & CAP_SHARED_KEY ? "(shared)" : + "(open)") : "", + priv->capability & CAP_PRIVACY_ON ? " key=" : "", + priv->capability & CAP_PRIVACY_ON ? + '1' + priv->sec.active_key : '.', + priv->capability & CAP_PRIVACY_ON ? + '.' : ' '); + + priv->assoc_request.beacon_interval = network->beacon_interval; + if ((priv->ieee->iw_mode == IW_MODE_ADHOC) && + (network->time_stamp[0] == 0) && + (network->time_stamp[1] == 0)) { + priv->assoc_request.assoc_type = HC_IBSS_START; + priv->assoc_request.assoc_tsf_msw = 0; + priv->assoc_request.assoc_tsf_lsw = 0; + } else { + if (unlikely(roaming)) + priv->assoc_request.assoc_type = HC_REASSOCIATE; + else + priv->assoc_request.assoc_type = HC_ASSOCIATE; + priv->assoc_request.assoc_tsf_msw = network->time_stamp[1]; + priv->assoc_request.assoc_tsf_lsw = network->time_stamp[0]; + } + + memcpy(&priv->assoc_request.bssid, network->bssid, ETH_ALEN); + + if (priv->ieee->iw_mode == IW_MODE_ADHOC) { + memset(&priv->assoc_request.dest, 0xFF, ETH_ALEN); + priv->assoc_request.atim_window = network->atim_window; + } else { + memcpy(&priv->assoc_request.dest, network->bssid, + ETH_ALEN); + priv->assoc_request.atim_window = 0; + } + + priv->assoc_request.capability = network->capability; + priv->assoc_request.listen_interval = network->listen_interval; + + err = ipw_send_ssid(priv, priv->essid, priv->essid_len); + if (err) { + IPW_DEBUG_HC("Attempt to send SSID command failed.\n"); + return err; + } + + rates->ieee_mode = priv->assoc_request.ieee_mode; + rates->purpose = IPW_RATE_CONNECT; + ipw_send_supported_rates(priv, rates); + + if (priv->assoc_request.ieee_mode == IPW_G_MODE) + priv->sys_config.dot11g_auto_detection = 1; + else + priv->sys_config.dot11g_auto_detection = 0; + err = ipw_send_system_config(priv, &priv->sys_config); + if (err) { + IPW_DEBUG_HC("Attempt to send sys config command failed.\n"); + return err; + } + + IPW_DEBUG_ASSOC("Association sensitivity: %d\n", network->stats.rssi); + err = ipw_set_sensitivity(priv, network->stats.rssi); + if (err) { + IPW_DEBUG_HC("Attempt to send associate command failed.\n"); + return err; + } + + /* + * If preemption is enabled, it is possible for the association + * to complete before we return from ipw_send_associate. Therefore + * we have to be sure and update our priviate data first. + */ + priv->channel = network->channel; + memcpy(priv->bssid, network->bssid, ETH_ALEN); + priv->status |= STATUS_ASSOCIATING; + priv->status &= ~STATUS_SECURITY_UPDATED; + + priv->assoc_network = network; + + err = ipw_send_associate(priv, &priv->assoc_request); + if (err) { + IPW_DEBUG_HC("Attempt to send associate command failed.\n"); + return err; + } + + IPW_DEBUG(IPW_DL_STATE, "associating: '%s' " MAC_FMT " \n", + escape_essid(priv->essid, priv->essid_len), + MAC_ARG(priv->bssid)); + + return 0; +} + +static void ipw_roam(void *data) +{ + struct ipw_priv *priv = data; + struct ieee80211_network *network = NULL; + struct ipw_network_match match = { + .network = priv->assoc_network + }; + + /* The roaming process is as follows: + * + * 1. Missed beacon threshold triggers the roaming process by + * setting the status ROAM bit and requesting a scan. + * 2. When the scan completes, it schedules the ROAM work + * 3. The ROAM work looks at all of the known networks for one that + * is a better network than the currently associated. If none + * found, the ROAM process is over (ROAM bit cleared) + * 4. If a better network is found, a disassociation request is + * sent. + * 5. When the disassociation completes, the roam work is again + * scheduled. The second time through, the driver is no longer + * associated, and the newly selected network is sent an + * association request. + * 6. At this point ,the roaming process is complete and the ROAM + * status bit is cleared. + */ + + /* If we are no longer associated, and the roaming bit is no longer + * set, then we are not actively roaming, so just return */ + if (!(priv->status & (STATUS_ASSOCIATED | STATUS_ROAMING))) + return; + + if (priv->status & STATUS_ASSOCIATED) { + /* First pass through ROAM process -- look for a better + * network */ + u8 rssi = priv->assoc_network->stats.rssi; + priv->assoc_network->stats.rssi = -128; + list_for_each_entry(network, &priv->ieee->network_list, list) { + if (network != priv->assoc_network) + ipw_best_network(priv, &match, network, 1); + } + priv->assoc_network->stats.rssi = rssi; + + if (match.network == priv->assoc_network) { + IPW_DEBUG_ASSOC("No better APs in this network to " + "roam to.\n"); + priv->status &= ~STATUS_ROAMING; + ipw_debug_config(priv); + return; + } + + ipw_send_disassociate(priv, 1); + priv->assoc_network = match.network; + + return; + } + + /* Second pass through ROAM process -- request association */ + ipw_compatible_rates(priv, priv->assoc_network, &match.rates); + ipw_associate_network(priv, priv->assoc_network, &match.rates, 1); + priv->status &= ~STATUS_ROAMING; +} + +static void ipw_associate(void *data) +{ + struct ipw_priv *priv = data; + + struct ieee80211_network *network = NULL; + struct ipw_network_match match = { + .network = NULL + }; + struct ipw_supported_rates *rates; + struct list_head *element; + + if (!(priv->config & CFG_ASSOCIATE) && + !(priv->config & (CFG_STATIC_ESSID | + CFG_STATIC_CHANNEL | + CFG_STATIC_BSSID))) { + IPW_DEBUG_ASSOC("Not attempting association (associate=0)\n"); + return; + } + + list_for_each_entry(network, &priv->ieee->network_list, list) + ipw_best_network(priv, &match, network, 0); + + network = match.network; + rates = &match.rates; + + if (network == NULL && + priv->ieee->iw_mode == IW_MODE_ADHOC && + priv->config & CFG_ADHOC_CREATE && + priv->config & CFG_STATIC_ESSID && + !list_empty(&priv->ieee->network_free_list)) { + element = priv->ieee->network_free_list.next; + network = list_entry(element, struct ieee80211_network, + list); + ipw_adhoc_create(priv, network); + rates = &priv->rates; + list_del(element); + list_add_tail(&network->list, &priv->ieee->network_list); + } + + /* If we reached the end of the list, then we don't have any valid + * matching APs */ + if (!network) { + ipw_debug_config(priv); + + queue_delayed_work(priv->workqueue, &priv->request_scan, + SCAN_INTERVAL); + + return; + } + + ipw_associate_network(priv, network, rates, 0); +} + +static inline void ipw_handle_data_packet(struct ipw_priv *priv, + struct ipw_rx_mem_buffer *rxb, + struct ieee80211_rx_stats *stats) +{ + struct ipw_rx_packet *pkt = (struct ipw_rx_packet *)rxb->skb->data; + + /* We received data from the HW, so stop the watchdog */ + priv->net_dev->trans_start = jiffies; + + /* We only process data packets if the + * interface is open */ + if (unlikely((pkt->u.frame.length + IPW_RX_FRAME_SIZE) > + skb_tailroom(rxb->skb))) { + priv->ieee->stats.rx_errors++; + priv->wstats.discard.misc++; + IPW_DEBUG_DROP("Corruption detected! Oh no!\n"); + return; + } else if (unlikely(!netif_running(priv->net_dev))) { + priv->ieee->stats.rx_dropped++; + priv->wstats.discard.misc++; + IPW_DEBUG_DROP("Dropping packet while interface is not up.\n"); + return; + } + + /* Advance skb->data to the start of the actual payload */ + skb_reserve(rxb->skb, (u32)&pkt->u.frame.data[0] - (u32)pkt); + + /* Set the size of the skb to the size of the frame */ + skb_put(rxb->skb, pkt->u.frame.length); + + IPW_DEBUG_RX("Rx packet of %d bytes.\n", rxb->skb->len); + + if (!ieee80211_rx(priv->ieee, rxb->skb, stats)) + priv->ieee->stats.rx_errors++; + else /* ieee80211_rx succeeded, so it now owns the SKB */ + rxb->skb = NULL; +} + + +/* + * Main entry function for recieving a packet with 80211 headers. This + * should be called when ever the FW has notified us that there is a new + * skb in the recieve queue. + */ +static void ipw_rx(struct ipw_priv *priv) +{ + struct ipw_rx_mem_buffer *rxb; + struct ipw_rx_packet *pkt; + struct ieee80211_hdr *header; + u32 r, w, i; + u8 network_packet; + + r = ipw_read32(priv, CX2_RX_READ_INDEX); + w = ipw_read32(priv, CX2_RX_WRITE_INDEX); + i = (priv->rxq->processed + 1) % RX_QUEUE_SIZE; + + while (i != r) { + rxb = priv->rxq->queue[i]; +#ifdef CONFIG_IPW_DEBUG + if (unlikely(rxb == NULL)) { + printk(KERN_CRIT "Queue not allocated!\n"); + break; + } +#endif + priv->rxq->queue[i] = NULL; + + pci_dma_sync_single_for_cpu(priv->pci_dev, rxb->dma_addr, + CX2_RX_BUF_SIZE, + PCI_DMA_FROMDEVICE); + + pkt = (struct ipw_rx_packet *)rxb->skb->data; + IPW_DEBUG_RX("Packet: type=%02X seq=%02X bits=%02X\n", + pkt->header.message_type, + pkt->header.rx_seq_num, + pkt->header.control_bits); + + switch (pkt->header.message_type) { + case RX_FRAME_TYPE: /* 802.11 frame */ { + struct ieee80211_rx_stats stats = { + .rssi = pkt->u.frame.rssi_dbm - + IPW_RSSI_TO_DBM, + .signal = pkt->u.frame.signal, + .rate = pkt->u.frame.rate, + .mac_time = jiffies, + .received_channel = + pkt->u.frame.received_channel, + .freq = (pkt->u.frame.control & (1<<0)) ? + IEEE80211_24GHZ_BAND : IEEE80211_52GHZ_BAND, + .len = pkt->u.frame.length, + }; + + if (stats.rssi != 0) + stats.mask |= IEEE80211_STATMASK_RSSI; + if (stats.signal != 0) + stats.mask |= IEEE80211_STATMASK_SIGNAL; + if (stats.rate != 0) + stats.mask |= IEEE80211_STATMASK_RATE; + + priv->rx_packets++; + +#ifdef CONFIG_IPW_PROMISC + if (priv->ieee->iw_mode == IW_MODE_MONITOR) { + ipw_handle_data_packet(priv, rxb, &stats); + break; + } +#endif + + header = (struct ieee80211_hdr *)(rxb->skb->data + + IPW_RX_FRAME_SIZE); + /* TODO: Check Ad-Hoc dest/source and make sure + * that we are actually parsing these packets + * correctly -- we should probably use the + * frame control of the packet and disregard + * the current iw_mode */ + switch (priv->ieee->iw_mode) { + case IW_MODE_ADHOC: + network_packet = + !memcmp(header->addr1, + priv->net_dev->dev_addr, + ETH_ALEN) || + !memcmp(header->addr3, + priv->bssid, ETH_ALEN) || + is_broadcast_ether_addr(header->addr1) || + is_multicast_ether_addr(header->addr1); + break; + + case IW_MODE_INFRA: + default: + network_packet = + !memcmp(header->addr3, + priv->bssid, ETH_ALEN) || + !memcmp(header->addr1, + priv->net_dev->dev_addr, + ETH_ALEN) || + is_broadcast_ether_addr(header->addr1) || + is_multicast_ether_addr(header->addr1); + break; + } + + if (network_packet && priv->assoc_network) { + priv->assoc_network->stats.rssi = stats.rssi; + average_add(&priv->average_rssi, + stats.rssi); + priv->last_rx_rssi = stats.rssi; + } + + IPW_DEBUG_RX("Frame: len=%u\n", pkt->u.frame.length); + + if (pkt->u.frame.length < frame_hdr_len(header)) { + IPW_DEBUG_DROP("Received packet is too small. " + "Dropping.\n"); + priv->ieee->stats.rx_errors++; + priv->wstats.discard.misc++; + break; + } + + switch (WLAN_FC_GET_TYPE(header->frame_ctl)) { + case IEEE80211_FTYPE_MGMT: + ieee80211_rx_mgt(priv->ieee, header, &stats); + if (priv->ieee->iw_mode == IW_MODE_ADHOC && + ((WLAN_FC_GET_STYPE(header->frame_ctl) == + IEEE80211_STYPE_PROBE_RESP) || + (WLAN_FC_GET_STYPE(header->frame_ctl) == + IEEE80211_STYPE_BEACON)) && + !memcmp(header->addr3, priv->bssid, ETH_ALEN)) + ipw_add_station(priv, header->addr2); + break; + + case IEEE80211_FTYPE_CTL: + break; + + case IEEE80211_FTYPE_DATA: + if (network_packet) + ipw_handle_data_packet(priv, rxb, &stats); + else + IPW_DEBUG_DROP("Dropping: " MAC_FMT + ", " MAC_FMT ", " MAC_FMT "\n", + MAC_ARG(header->addr1), MAC_ARG(header->addr2), + MAC_ARG(header->addr3)); + break; + } + break; + } + + case RX_HOST_NOTIFICATION_TYPE: { + IPW_DEBUG_RX("Notification: subtype=%02X flags=%02X size=%d\n", + pkt->u.notification.subtype, + pkt->u.notification.flags, + pkt->u.notification.size); + ipw_rx_notification(priv, &pkt->u.notification); + break; + } + + default: + IPW_DEBUG_RX("Bad Rx packet of type %d\n", + pkt->header.message_type); + break; + } + + /* For now we just don't re-use anything. We can tweak this + * later to try and re-use notification packets and SKBs that + * fail to Rx correctly */ + if (rxb->skb != NULL) { + dev_kfree_skb_any(rxb->skb); + rxb->skb = NULL; + } + + pci_unmap_single(priv->pci_dev, rxb->dma_addr, + CX2_RX_BUF_SIZE, PCI_DMA_FROMDEVICE); + list_add_tail(&rxb->list, &priv->rxq->rx_used); + + i = (i + 1) % RX_QUEUE_SIZE; + } + + /* Backtrack one entry */ + priv->rxq->processed = (i ? i : RX_QUEUE_SIZE) - 1; + + ipw_rx_queue_restock(priv); +} + +static void ipw_abort_scan(struct ipw_priv *priv) +{ + int err; + + if (priv->status & STATUS_SCAN_ABORTING) { + IPW_DEBUG_HC("Ignoring concurrent scan abort request.\n"); + return; + } + priv->status |= STATUS_SCAN_ABORTING; + + err = ipw_send_scan_abort(priv); + if (err) + IPW_DEBUG_HC("Request to abort scan failed.\n"); +} + +static int ipw_request_scan(struct ipw_priv *priv) +{ + struct ipw_scan_request_ext scan; + int channel_index = 0; + int i, err, scan_type; + + if (priv->status & STATUS_EXIT_PENDING) { + IPW_DEBUG_SCAN("Aborting scan due to device shutdown\n"); + priv->status |= STATUS_SCAN_PENDING; + return 0; + } + + if (priv->status & STATUS_SCANNING) { + IPW_DEBUG_HC("Concurrent scan requested. Aborting first.\n"); + priv->status |= STATUS_SCAN_PENDING; + ipw_abort_scan(priv); + return 0; + } + + if (priv->status & STATUS_SCAN_ABORTING) { + IPW_DEBUG_HC("Scan request while abort pending. Queuing.\n"); + priv->status |= STATUS_SCAN_PENDING; + return 0; + } + + if (priv->status & STATUS_RF_KILL_MASK) { + IPW_DEBUG_HC("Aborting scan due to RF Kill activation\n"); + priv->status |= STATUS_SCAN_PENDING; + return 0; + } + + memset(&scan, 0, sizeof(scan)); + + scan.dwell_time[IPW_SCAN_ACTIVE_BROADCAST_SCAN] = 20; + scan.dwell_time[IPW_SCAN_ACTIVE_BROADCAST_AND_DIRECT_SCAN] = 20; + scan.dwell_time[IPW_SCAN_PASSIVE_FULL_DWELL_SCAN] = 20; + + scan.full_scan_index = ieee80211_get_scans(priv->ieee); + /* If we are roaming, then make this a directed scan for the current + * network. Otherwise, ensure that every other scan is a fast + * channel hop scan */ + if ((priv->status & STATUS_ROAMING) || ( + !(priv->status & STATUS_ASSOCIATED) && + (priv->config & CFG_STATIC_ESSID) && + (scan.full_scan_index % 2))) { + err = ipw_send_ssid(priv, priv->essid, priv->essid_len); + if (err) { + IPW_DEBUG_HC("Attempt to send SSID command failed.\n"); + return err; + } + + scan_type = IPW_SCAN_ACTIVE_BROADCAST_AND_DIRECT_SCAN; + } else { + scan_type = IPW_SCAN_ACTIVE_BROADCAST_SCAN; + } + + if (priv->ieee->freq_band & IEEE80211_52GHZ_BAND) { + int start = channel_index; + for (i = 0; i < MAX_A_CHANNELS; i++) { + if (band_a_active_channel[i] == 0) + break; + if ((priv->status & STATUS_ASSOCIATED) && + band_a_active_channel[i] == priv->channel) + continue; + channel_index++; + scan.channels_list[channel_index] = + band_a_active_channel[i]; + ipw_set_scan_type(&scan, channel_index, scan_type); + } + + if (start != channel_index) { + scan.channels_list[start] = (u8)(IPW_A_MODE << 6) | + (channel_index - start); + channel_index++; + } + } + + if (priv->ieee->freq_band & IEEE80211_24GHZ_BAND) { + int start = channel_index; + for (i = 0; i < MAX_B_CHANNELS; i++) { + if (band_b_active_channel[i] == 0) + break; + if ((priv->status & STATUS_ASSOCIATED) && + band_b_active_channel[i] == priv->channel) + continue; + channel_index++; + scan.channels_list[channel_index] = + band_b_active_channel[i]; + ipw_set_scan_type(&scan, channel_index, scan_type); + } + + if (start != channel_index) { + scan.channels_list[start] = (u8)(IPW_B_MODE << 6) | + (channel_index - start); + } + } + + err = ipw_send_scan_request_ext(priv, &scan); + if (err) { + IPW_DEBUG_HC("Sending scan command failed: %08X\n", + err); + return -EIO; + } + + priv->status |= STATUS_SCANNING; + priv->status &= ~STATUS_SCAN_PENDING; + + return 0; +} + +/* + * This file defines the Wireless Extension handlers. It does not + * define any methods of hardware manipulation and relies on the + * functions defined in ipw_main to provide the HW interaction. + * + * The exception to this is the use of the ipw_get_ordinal() + * function used to poll the hardware vs. making unecessary calls. + * + */ + +static int ipw_wx_get_name(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + if (!(priv->status & STATUS_ASSOCIATED)) + strcpy(wrqu->name, "unassociated"); + else + snprintf(wrqu->name, IFNAMSIZ, "IEEE 802.11%c", + ipw_modes[priv->assoc_request.ieee_mode]); + IPW_DEBUG_WX("Name: %s\n", wrqu->name); + return 0; +} + +static int ipw_set_channel(struct ipw_priv *priv, u8 channel) +{ + if (channel == 0) { + IPW_DEBUG_INFO("Setting channel to ANY (0)\n"); + priv->config &= ~CFG_STATIC_CHANNEL; + if (!(priv->status & (STATUS_SCANNING | STATUS_ASSOCIATED | + STATUS_ASSOCIATING))) { + IPW_DEBUG_ASSOC("Attempting to associate with new " + "parameters.\n"); + ipw_associate(priv); + } + + return 0; + } + + priv->config |= CFG_STATIC_CHANNEL; + + if (priv->channel == channel) { + IPW_DEBUG_INFO( + "Request to set channel to current value (%d)\n", + channel); + return 0; + } + + IPW_DEBUG_INFO("Setting channel to %i\n", (int)channel); + priv->channel = channel; + + /* If we are currently associated, or trying to associate + * then see if this is a new channel (causing us to disassociate) */ + if (priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) { + IPW_DEBUG_ASSOC("Disassociating due to channel change.\n"); + ipw_disassociate(priv); + } else { + ipw_associate(priv); + } + + return 0; +} + +static int ipw_wx_set_freq(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + struct iw_freq *fwrq = &wrqu->freq; + + /* if setting by freq convert to channel */ + if (fwrq->e == 1) { + if ((fwrq->m >= (int) 2.412e8 && + fwrq->m <= (int) 2.487e8)) { + int f = fwrq->m / 100000; + int c = 0; + + while ((c < REG_MAX_CHANNEL) && + (f != ipw_frequencies[c])) + c++; + + /* hack to fall through */ + fwrq->e = 0; + fwrq->m = c + 1; + } + } + + if (fwrq->e > 0 || fwrq->m > 1000) + return -EOPNOTSUPP; + + IPW_DEBUG_WX("SET Freq/Channel -> %d \n", fwrq->m); + return ipw_set_channel(priv, (u8)fwrq->m); + + return 0; +} + + +static int ipw_wx_get_freq(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + wrqu->freq.e = 0; + + /* If we are associated, trying to associate, or have a statically + * configured CHANNEL then return that; otherwise return ANY */ + if (priv->config & CFG_STATIC_CHANNEL || + priv->status & (STATUS_ASSOCIATING | STATUS_ASSOCIATED)) + wrqu->freq.m = priv->channel; + else + wrqu->freq.m = 0; + + IPW_DEBUG_WX("GET Freq/Channel -> %d \n", priv->channel); + return 0; +} + +static int ipw_wx_set_mode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int err = 0; + + IPW_DEBUG_WX("Set MODE: %d\n", wrqu->mode); + + if (wrqu->mode == priv->ieee->iw_mode) + return 0; + + switch (wrqu->mode) { +#ifdef CONFIG_IPW_PROMISC + case IW_MODE_MONITOR: +#endif + case IW_MODE_ADHOC: + case IW_MODE_INFRA: + break; + case IW_MODE_AUTO: + wrqu->mode = IW_MODE_INFRA; + break; + default: + return -EINVAL; + } + +#ifdef CONFIG_IPW_PROMISC + if (priv->ieee->iw_mode == IW_MODE_MONITOR) + priv->net_dev->type = ARPHRD_ETHER; + + if (wrqu->mode == IW_MODE_MONITOR) + priv->net_dev->type = ARPHRD_IEEE80211; +#endif /* CONFIG_IPW_PROMISC */ + +#ifdef CONFIG_PM + /* Free the existing firmware and reset the fw_loaded + * flag so ipw_load() will bring in the new firmawre */ + if (fw_loaded) { + fw_loaded = 0; + } + + release_firmware(bootfw); + release_firmware(ucode); + release_firmware(firmware); + bootfw = ucode = firmware = NULL; +#endif + + priv->ieee->iw_mode = wrqu->mode; + ipw_adapter_restart(priv); + + return err; +} + +static int ipw_wx_get_mode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + wrqu->mode = priv->ieee->iw_mode; + IPW_DEBUG_WX("Get MODE -> %d\n", wrqu->mode); + + return 0; +} + + +#define DEFAULT_RTS_THRESHOLD 2304U +#define MIN_RTS_THRESHOLD 1U +#define MAX_RTS_THRESHOLD 2304U +#define DEFAULT_BEACON_INTERVAL 100U +#define DEFAULT_SHORT_RETRY_LIMIT 7U +#define DEFAULT_LONG_RETRY_LIMIT 4U + +/* Values are in microsecond */ +static const s32 timeout_duration[] = { + 350000, + 250000, + 75000, + 37000, + 25000, +}; + +static const s32 period_duration[] = { + 400000, + 700000, + 1000000, + 1000000, + 1000000 +}; + +static int ipw_wx_get_range(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + struct iw_range *range = (struct iw_range *)extra; + u16 val; + int i; + + wrqu->data.length = sizeof(*range); + memset(range, 0, sizeof(*range)); + + /* 54Mbs == ~27 Mb/s real (802.11g) */ + range->throughput = 27 * 1000 * 1000; + + range->max_qual.qual = 100; + /* TODO: Find real max RSSI and stick here */ + range->max_qual.level = 0; + range->max_qual.noise = 0; + range->max_qual.updated = 7; /* Updated all three */ + + range->avg_qual.qual = 70; + /* TODO: Find real 'good' to 'bad' threshol value for RSSI */ + range->avg_qual.level = 0; /* FIXME to real average level */ + range->avg_qual.noise = 0; + range->avg_qual.updated = 7; /* Updated all three */ + + range->num_bitrates = min(priv->rates.num_rates, (u8)IW_MAX_BITRATES); + + for (i = 0; i < range->num_bitrates; i++) + range->bitrate[i] = (priv->rates.supported_rates[i] & 0x7F) * + 500000; + + range->max_rts = DEFAULT_RTS_THRESHOLD; + range->min_frag = MIN_FRAG_THRESHOLD; + range->max_frag = MAX_FRAG_THRESHOLD; + + range->encoding_size[0] = 5; + range->encoding_size[1] = 13; + range->num_encoding_sizes = 2; + range->max_encoding_tokens = WEP_KEYS; + + /* Set the Wireless Extension versions */ + range->we_version_compiled = WIRELESS_EXT; + range->we_version_source = 16; + + range->num_channels = FREQ_COUNT; + + val = 0; + for (i = 0; i < FREQ_COUNT; i++) { + range->freq[val].i = i + 1; + range->freq[val].m = ipw_frequencies[i] * 100000; + range->freq[val].e = 1; + val++; + + if (val == IW_MAX_FREQUENCIES) + break; + } + range->num_frequency = val; + + IPW_DEBUG_WX("GET Range\n"); + return 0; +} + +static int ipw_wx_set_wap(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + static const unsigned char any[] = { + 0xff, 0xff, 0xff, 0xff, 0xff, 0xff + }; + static const unsigned char off[] = { + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + }; + + if (wrqu->ap_addr.sa_family != ARPHRD_ETHER) + return -EINVAL; + + if (!memcmp(any, wrqu->ap_addr.sa_data, ETH_ALEN) || + !memcmp(off, wrqu->ap_addr.sa_data, ETH_ALEN)) { + /* we disable mandatory BSSID association */ + IPW_DEBUG_WX("Setting AP BSSID to ANY\n"); + priv->config &= ~CFG_STATIC_BSSID; + if (!(priv->status & (STATUS_SCANNING | STATUS_ASSOCIATED | + STATUS_ASSOCIATING))) { + IPW_DEBUG_ASSOC("Attempting to associate with new " + "parameters.\n"); + ipw_associate(priv); + } + + return 0; + } + + priv->config |= CFG_STATIC_BSSID; + if (!memcmp(priv->bssid, wrqu->ap_addr.sa_data, ETH_ALEN)) { + IPW_DEBUG_WX("BSSID set to current BSSID.\n"); + return 0; + } + + IPW_DEBUG_WX("Setting mandatory BSSID to " MAC_FMT "\n", + MAC_ARG(wrqu->ap_addr.sa_data)); + + memcpy(priv->bssid, wrqu->ap_addr.sa_data, ETH_ALEN); + + /* If we are currently associated, or trying to associate + * then see if this is a new BSSID (causing us to disassociate) */ + if (priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) { + IPW_DEBUG_ASSOC("Disassociating due to BSSID change.\n"); + ipw_disassociate(priv); + } else { + ipw_associate(priv); + } + + return 0; +} + +static int ipw_wx_get_wap(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + /* If we are associated, trying to associate, or have a statically + * configured BSSID then return that; otherwise return ANY */ + if (priv->config & CFG_STATIC_BSSID || + priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) { + wrqu->ap_addr.sa_family = ARPHRD_ETHER; + memcpy(wrqu->ap_addr.sa_data, &priv->bssid, ETH_ALEN); + } else + memset(wrqu->ap_addr.sa_data, 0, ETH_ALEN); + + IPW_DEBUG_WX("Getting WAP BSSID: " MAC_FMT "\n", + MAC_ARG(wrqu->ap_addr.sa_data)); + return 0; +} + +static int ipw_wx_set_essid(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + char *essid = ""; /* ANY */ + int length = 0; + + if (wrqu->essid.flags && wrqu->essid.length) { + length = wrqu->essid.length - 1; + essid = extra; + } + if (length == 0) { + IPW_DEBUG_WX("Setting ESSID to ANY\n"); + priv->config &= ~CFG_STATIC_ESSID; + if (!(priv->status & (STATUS_SCANNING | STATUS_ASSOCIATED | + STATUS_ASSOCIATING))) { + IPW_DEBUG_ASSOC("Attempting to associate with new " + "parameters.\n"); + ipw_associate(priv); + } + + return 0; + } + + length = min(length, IW_ESSID_MAX_SIZE); + + priv->config |= CFG_STATIC_ESSID; + + if (priv->essid_len == length && !memcmp(priv->essid, extra, length)) { + IPW_DEBUG_WX("ESSID set to current ESSID.\n"); + return 0; + } + + IPW_DEBUG_WX("Setting ESSID: '%s' (%d)\n", escape_essid(essid, length), + length); + + priv->essid_len = length; + memcpy(priv->essid, essid, priv->essid_len); + + /* If we are currently associated, or trying to associate + * then see if this is a new ESSID (causing us to disassociate) */ + if (priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) { + IPW_DEBUG_ASSOC("Disassociating due to ESSID change.\n"); + ipw_disassociate(priv); + } else { + ipw_associate(priv); + } + + return 0; +} + +static int ipw_wx_get_essid(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + /* If we are associated, trying to associate, or have a statically + * configured ESSID then return that; otherwise return ANY */ + if (priv->config & CFG_STATIC_ESSID || + priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) { + IPW_DEBUG_WX("Getting essid: '%s'\n", + escape_essid(priv->essid, priv->essid_len)); + memcpy(extra, priv->essid, priv->essid_len); + wrqu->essid.length = priv->essid_len; + wrqu->essid.flags = 1; /* active */ + } else { + IPW_DEBUG_WX("Getting essid: ANY\n"); + wrqu->essid.length = 0; + wrqu->essid.flags = 0; /* active */ + } + + return 0; +} + +static int ipw_wx_set_nick(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + IPW_DEBUG_WX("Setting nick to '%s'\n", extra); + if (wrqu->data.length > IW_ESSID_MAX_SIZE) + return -E2BIG; + + wrqu->data.length = min((size_t)wrqu->data.length, sizeof(priv->nick)); + memset(priv->nick, 0, sizeof(priv->nick)); + memcpy(priv->nick, extra, wrqu->data.length); + IPW_DEBUG_TRACE("<<\n"); + return 0; + +} + + +static int ipw_wx_get_nick(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + IPW_DEBUG_WX("Getting nick\n"); + wrqu->data.length = strlen(priv->nick) + 1; + memcpy(extra, priv->nick, wrqu->data.length); + wrqu->data.flags = 1; /* active */ + return 0; +} + + +static int ipw_wx_set_rate(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + IPW_DEBUG_WX("0x%p, 0x%p, 0x%p\n", dev, info, wrqu); + return -EOPNOTSUPP; +} + +static int ipw_wx_get_rate(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv * priv = ieee80211_priv(dev); + wrqu->bitrate.value = priv->last_rate; + + IPW_DEBUG_WX("GET Rate -> %d \n", wrqu->bitrate.value); + return 0; +} + + +static int ipw_wx_set_rts(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + if (wrqu->rts.disabled) + priv->rts_threshold = DEFAULT_RTS_THRESHOLD; + else { + if (wrqu->rts.value < MIN_RTS_THRESHOLD || + wrqu->rts.value > MAX_RTS_THRESHOLD) + return -EINVAL; + + priv->rts_threshold = wrqu->rts.value; + } + + ipw_send_rts_threshold(priv, priv->rts_threshold); + IPW_DEBUG_WX("SET RTS Threshold -> %d \n", priv->rts_threshold); + return 0; +} + +static int ipw_wx_get_rts(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + wrqu->rts.value = priv->rts_threshold; + wrqu->rts.fixed = 0; /* no auto select */ + wrqu->rts.disabled = + (wrqu->rts.value == DEFAULT_RTS_THRESHOLD); + + IPW_DEBUG_WX("GET RTS Threshold -> %d \n", wrqu->rts.value); + return 0; +} + + +static int ipw_wx_set_txpow(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + struct ipw_tx_power tx_power; + int i; + + if (ipw_radio_kill_sw(priv, wrqu->power.disabled)) + return -EINPROGRESS; + + if (wrqu->power.flags != IW_TXPOW_DBM) + return -EINVAL; + + if ((wrqu->power.value > 20) || + (wrqu->power.value < -12)) + return -EINVAL; + + priv->tx_power = wrqu->power.value; + + memset(&tx_power, 0, sizeof(tx_power)); + + /* configure device for 'G' band */ + tx_power.ieee_mode = IPW_G_MODE; + tx_power.num_channels = 11; + for (i = 0; i < 11; i++) { + tx_power.channels_tx_power[i].channel_number = i + 1; + tx_power.channels_tx_power[i].tx_power = priv->tx_power; + } + if (ipw_send_tx_power(priv, &tx_power)) + goto error; + + /* configure device to also handle 'B' band */ + tx_power.ieee_mode = IPW_B_MODE; + if (ipw_send_tx_power(priv, &tx_power)) + goto error; + + return 0; + + error: + return -EIO; +} + + +static int ipw_wx_get_txpow(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + wrqu->power.value = priv->tx_power; + wrqu->power.fixed = 1; + wrqu->power.flags = IW_TXPOW_DBM; + wrqu->power.disabled = (priv->status & STATUS_RF_KILL_MASK) ? 1 : 0; + + IPW_DEBUG_WX("GET TX Power -> %s %d \n", + wrqu->power.disabled ? "ON" : "OFF", + wrqu->power.value); + + return 0; +} + +static int ipw_wx_set_frag(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + if (wrqu->frag.disabled) + priv->ieee->fts = DEFAULT_FTS; + else { + if (wrqu->frag.value < MIN_FRAG_THRESHOLD || + wrqu->frag.value > MAX_FRAG_THRESHOLD) + return -EINVAL; + + priv->ieee->fts = wrqu->frag.value & ~0x1; + } + + ipw_send_frag_threshold(priv, wrqu->frag.value); + IPW_DEBUG_WX("SET Frag Threshold -> %d \n", wrqu->frag.value); + return 0; +} + +static int ipw_wx_get_frag(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + wrqu->frag.value = priv->ieee->fts; + wrqu->frag.fixed = 0; /* no auto select */ + wrqu->frag.disabled = + (wrqu->frag.value == DEFAULT_FTS); + + IPW_DEBUG_WX("GET Frag Threshold -> %d \n", wrqu->frag.value); + + return 0; +} + +static int ipw_wx_set_retry(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + IPW_DEBUG_WX("0x%p, 0x%p, 0x%p\n", dev, info, wrqu); + return -EOPNOTSUPP; +} + + +static int ipw_wx_get_retry(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + IPW_DEBUG_WX("0x%p, 0x%p, 0x%p\n", dev, info, wrqu); + return -EOPNOTSUPP; +} + + +static int ipw_wx_set_scan(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + IPW_DEBUG_WX("Start scan\n"); + if (ipw_request_scan(priv)) + return -EIO; + return 0; +} + +static int ipw_wx_get_scan(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + return ieee80211_wx_get_scan(priv->ieee, info, wrqu, extra); +} + +static int ipw_wx_set_encode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + return ieee80211_wx_set_encode(priv->ieee, info, wrqu, key); +} + +static int ipw_wx_get_encode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + return ieee80211_wx_get_encode(priv->ieee, info, wrqu, key); +} + +static int ipw_wx_set_power(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int err; + + if (wrqu->power.disabled) { + priv->power_mode = IPW_POWER_LEVEL(priv->power_mode); + err = ipw_send_power_mode(priv, IPW_POWER_MODE_CAM); + if (err) { + IPW_DEBUG_WX("failed setting power mode.\n"); + return err; + } + + IPW_DEBUG_WX("SET Power Management Mode -> off\n"); + + return 0; + } + + switch (wrqu->power.flags & IW_POWER_MODE) { + case IW_POWER_ON: /* If not specified */ + case IW_POWER_MODE: /* If set all mask */ + case IW_POWER_ALL_R: /* If explicitely state all */ + break; + default: /* Otherwise we don't support it */ + IPW_DEBUG_WX("SET PM Mode: %X not supported.\n", + wrqu->power.flags); + return -EOPNOTSUPP; + } + + /* If the user hasn't specified a power management mode yet, default + * to BATTERY */ + if (IPW_POWER_LEVEL(priv->power_mode) == IPW_POWER_AC) + priv->power_mode = IPW_POWER_ENABLED | IPW_POWER_BATTERY; + else + priv->power_mode = IPW_POWER_ENABLED | priv->power_mode; + err = ipw_send_power_mode(priv, IPW_POWER_LEVEL(priv->power_mode)); + if (err) { + IPW_DEBUG_WX("failed setting power mode.\n"); + return err; + } + + IPW_DEBUG_WX("SET Power Management Mode -> 0x%02X\n", + priv->power_mode); + + return 0; +} + +static int ipw_wx_get_power(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + if (!(priv->power_mode & IPW_POWER_ENABLED)) { + wrqu->power.disabled = 1; + } else { + wrqu->power.disabled = 0; + } + + IPW_DEBUG_WX("GET Power Management Mode -> %02X\n", priv->power_mode); + + return 0; +} + +static int ipw_wx_set_powermode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int mode = *(int *)extra; + int err; + + if ((mode < 1) || (mode > IPW_POWER_LIMIT)) { + mode = IPW_POWER_AC; + priv->power_mode = mode; + } else { + priv->power_mode = IPW_POWER_ENABLED | mode; + } + + if (priv->power_mode != mode) { + err = ipw_send_power_mode(priv, mode); + + if (err) { + IPW_DEBUG_WX("failed setting power mode.\n"); + return err; + } + } + + return 0; +} + +#define MAX_WX_STRING 80 +static int ipw_wx_get_powermode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int level = IPW_POWER_LEVEL(priv->power_mode); + char *p = extra; + + p += snprintf(p, MAX_WX_STRING, "Power save level: %d ", level); + + switch (level) { + case IPW_POWER_AC: + p += snprintf(p, MAX_WX_STRING - (p - extra), "(AC)"); + break; + case IPW_POWER_BATTERY: + p += snprintf(p, MAX_WX_STRING - (p - extra), "(BATTERY)"); + break; + default: + p += snprintf(p, MAX_WX_STRING - (p - extra), + "(Timeout %dms, Period %dms)", + timeout_duration[level - 1] / 1000, + period_duration[level - 1] / 1000); + } + + if (!(priv->power_mode & IPW_POWER_ENABLED)) + p += snprintf(p, MAX_WX_STRING - (p - extra)," OFF"); + + wrqu->data.length = p - extra + 1; + + return 0; +} + +static int ipw_wx_set_wireless_mode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int mode = *(int *)extra; + u8 band = 0, modulation = 0; + + if (mode == 0 || mode & ~IEEE_MODE_MASK) { + IPW_WARNING("Attempt to set invalid wireless mode: %d\n", + mode); + return -EINVAL; + } + + if (priv->adapter == IPW_2915ABG) { + priv->ieee->abg_ture = 1; + if (mode & IEEE_A) { + band |= IEEE80211_52GHZ_BAND; + modulation |= IEEE80211_OFDM_MODULATION; + } else + priv->ieee->abg_ture = 0; + } else { + if (mode & IEEE_A) { + IPW_WARNING("Attempt to set 2200BG into " + "802.11a mode\n"); + return -EINVAL; + } + + priv->ieee->abg_ture = 0; + } + + if (mode & IEEE_B) { + band |= IEEE80211_24GHZ_BAND; + modulation |= IEEE80211_CCK_MODULATION; + } else + priv->ieee->abg_ture = 0; + + if (mode & IEEE_G) { + band |= IEEE80211_24GHZ_BAND; + modulation |= IEEE80211_OFDM_MODULATION; + } else + priv->ieee->abg_ture = 0; + + priv->ieee->mode = mode; + priv->ieee->freq_band = band; + priv->ieee->modulation = modulation; + init_supported_rates(priv, &priv->rates); + + /* If we are currently associated, or trying to associate + * then see if this is a new configuration (causing us to + * disassociate) */ + if (priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) { + /* The resulting association will trigger + * the new rates to be sent to the device */ + IPW_DEBUG_ASSOC("Disassociating due to mode change.\n"); + ipw_disassociate(priv); + } else + ipw_send_supported_rates(priv, &priv->rates); + + IPW_DEBUG_WX("PRIV SET MODE: %c%c%c\n", + mode & IEEE_A ? 'a' : '.', + mode & IEEE_B ? 'b' : '.', + mode & IEEE_G ? 'g' : '.'); + return 0; +} + +static int ipw_wx_get_wireless_mode(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + switch (priv->ieee->freq_band) { + case IEEE80211_24GHZ_BAND: + switch (priv->ieee->modulation) { + case IEEE80211_CCK_MODULATION: + strncpy(extra, "802.11b (2)", MAX_WX_STRING); + break; + case IEEE80211_OFDM_MODULATION: + strncpy(extra, "802.11g (4)", MAX_WX_STRING); + break; + default: + strncpy(extra, "802.11bg (6)", MAX_WX_STRING); + break; + } + break; + + case IEEE80211_52GHZ_BAND: + strncpy(extra, "802.11a (1)", MAX_WX_STRING); + break; + + default: /* Mixed Band */ + switch (priv->ieee->modulation) { + case IEEE80211_CCK_MODULATION: + strncpy(extra, "802.11ab (3)", MAX_WX_STRING); + break; + case IEEE80211_OFDM_MODULATION: + strncpy(extra, "802.11ag (5)", MAX_WX_STRING); + break; + default: + strncpy(extra, "802.11abg (7)", MAX_WX_STRING); + break; + } + break; + } + + IPW_DEBUG_WX("PRIV GET MODE: %s\n", extra); + + wrqu->data.length = strlen(extra) + 1; + + return 0; +} + +#ifdef CONFIG_IPW_PROMISC +static int ipw_wx_set_promisc(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int *parms = (int *)extra; + int enable = (parms[0] > 0); + + IPW_DEBUG_WX("SET PROMISC: %d %d\n", enable, parms[1]); + if (enable) { + if (priv->ieee->iw_mode != IW_MODE_MONITOR) { + priv->net_dev->type = ARPHRD_IEEE80211; + ipw_adapter_restart(priv); + } + + ipw_set_channel(priv, parms[1]); + } else { + if (priv->ieee->iw_mode != IW_MODE_MONITOR) + return 0; + priv->net_dev->type = ARPHRD_ETHER; + ipw_adapter_restart(priv); + } + return 0; +} + + +static int ipw_wx_reset(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + IPW_DEBUG_WX("RESET\n"); + ipw_adapter_restart(priv); + return 0; +} +#endif // CONFIG_IPW_PROMISC + +/* Rebase the WE IOCTLs to zero for the handler array */ +#define IW_IOCTL(x) [(x)-SIOCSIWCOMMIT] +static iw_handler ipw_wx_handlers[] = +{ + IW_IOCTL(SIOCGIWNAME) = ipw_wx_get_name, + IW_IOCTL(SIOCSIWFREQ) = ipw_wx_set_freq, + IW_IOCTL(SIOCGIWFREQ) = ipw_wx_get_freq, + IW_IOCTL(SIOCSIWMODE) = ipw_wx_set_mode, + IW_IOCTL(SIOCGIWMODE) = ipw_wx_get_mode, + IW_IOCTL(SIOCGIWRANGE) = ipw_wx_get_range, + IW_IOCTL(SIOCSIWAP) = ipw_wx_set_wap, + IW_IOCTL(SIOCGIWAP) = ipw_wx_get_wap, + IW_IOCTL(SIOCSIWSCAN) = ipw_wx_set_scan, + IW_IOCTL(SIOCGIWSCAN) = ipw_wx_get_scan, + IW_IOCTL(SIOCSIWESSID) = ipw_wx_set_essid, + IW_IOCTL(SIOCGIWESSID) = ipw_wx_get_essid, + IW_IOCTL(SIOCSIWNICKN) = ipw_wx_set_nick, + IW_IOCTL(SIOCGIWNICKN) = ipw_wx_get_nick, + IW_IOCTL(SIOCSIWRATE) = ipw_wx_set_rate, + IW_IOCTL(SIOCGIWRATE) = ipw_wx_get_rate, + IW_IOCTL(SIOCSIWRTS) = ipw_wx_set_rts, + IW_IOCTL(SIOCGIWRTS) = ipw_wx_get_rts, + IW_IOCTL(SIOCSIWFRAG) = ipw_wx_set_frag, + IW_IOCTL(SIOCGIWFRAG) = ipw_wx_get_frag, + IW_IOCTL(SIOCSIWTXPOW) = ipw_wx_set_txpow, + IW_IOCTL(SIOCGIWTXPOW) = ipw_wx_get_txpow, + IW_IOCTL(SIOCSIWRETRY) = ipw_wx_set_retry, + IW_IOCTL(SIOCGIWRETRY) = ipw_wx_get_retry, + IW_IOCTL(SIOCSIWENCODE) = ipw_wx_set_encode, + IW_IOCTL(SIOCGIWENCODE) = ipw_wx_get_encode, + IW_IOCTL(SIOCSIWPOWER) = ipw_wx_set_power, + IW_IOCTL(SIOCGIWPOWER) = ipw_wx_get_power, +}; + +#define IPW_PRIV_SET_POWER SIOCIWFIRSTPRIV +#define IPW_PRIV_GET_POWER SIOCIWFIRSTPRIV+1 +#define IPW_PRIV_SET_MODE SIOCIWFIRSTPRIV+2 +#define IPW_PRIV_GET_MODE SIOCIWFIRSTPRIV+3 +#define IPW_PRIV_SET_PROMISC SIOCIWFIRSTPRIV+4 +#define IPW_PRIV_RESET SIOCIWFIRSTPRIV+5 + + +static struct iw_priv_args ipw_priv_args[] = { + { + .cmd = IPW_PRIV_SET_POWER, + .set_args = IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1, + .name = "set_power" + }, + { + .cmd = IPW_PRIV_GET_POWER, + .get_args = IW_PRIV_TYPE_CHAR | IW_PRIV_SIZE_FIXED | MAX_WX_STRING, + .name = "get_power" + }, + { + .cmd = IPW_PRIV_SET_MODE, + .set_args = IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1, + .name = "set_mode" + }, + { + .cmd = IPW_PRIV_GET_MODE, + .get_args = IW_PRIV_TYPE_CHAR | IW_PRIV_SIZE_FIXED | MAX_WX_STRING, + .name = "get_mode" + }, +#ifdef CONFIG_IPW_PROMISC + { + IPW_PRIV_SET_PROMISC, + IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 2, 0, "monitor" + }, + { + IPW_PRIV_RESET, + IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 0, 0, "reset" + }, +#endif /* CONFIG_IPW_PROMISC */ +}; + +static iw_handler ipw_priv_handler[] = { + ipw_wx_set_powermode, + ipw_wx_get_powermode, + ipw_wx_set_wireless_mode, + ipw_wx_get_wireless_mode, +#ifdef CONFIG_IPW_PROMISC + ipw_wx_set_promisc, + ipw_wx_reset, +#endif +}; + +static struct iw_handler_def ipw_wx_handler_def = +{ + .standard = ipw_wx_handlers, + .num_standard = ARRAY_SIZE(ipw_wx_handlers), + .num_private = ARRAY_SIZE(ipw_priv_handler), + .num_private_args = ARRAY_SIZE(ipw_priv_args), + .private = ipw_priv_handler, + .private_args = ipw_priv_args, +}; + + + + +/* + * Get wireless statistics. + * Called by /proc/net/wireless + * Also called by SIOCGIWSTATS + */ +static struct iw_statistics *ipw_get_wireless_stats(struct net_device * dev) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + struct iw_statistics *wstats; + + wstats = &priv->wstats; + + /* if hw is disabled, then ipw2100_get_ordinal() can't be called. + * ipw2100_wx_wireless_stats seems to be called before fw is + * initialized. STATUS_ASSOCIATED will only be set if the hw is up + * and associated; if not associcated, the values are all meaningless + * anyway, so set them all to NULL and INVALID */ + if (!(priv->status & STATUS_ASSOCIATED)) { + wstats->miss.beacon = 0; + wstats->discard.retries = 0; + wstats->qual.qual = 0; + wstats->qual.level = 0; + wstats->qual.noise = 0; + wstats->qual.updated = 7; + wstats->qual.updated |= IW_QUAL_NOISE_INVALID | + IW_QUAL_QUAL_INVALID | IW_QUAL_LEVEL_INVALID; + return wstats; + } + + wstats->qual.qual = priv->quality; + wstats->qual.level = average_value(&priv->average_rssi); + wstats->qual.noise = average_value(&priv->average_noise); + wstats->qual.updated = IW_QUAL_QUAL_UPDATED | IW_QUAL_LEVEL_UPDATED | + IW_QUAL_NOISE_UPDATED; + + wstats->miss.beacon = average_value(&priv->average_missed_beacons); + wstats->discard.retries = priv->last_tx_failures; + wstats->discard.code = priv->ieee->ieee_stats.rx_discards_undecryptable; + +/* if (ipw_get_ordinal(priv, IPW_ORD_STAT_TX_RETRY, &tx_retry, &len)) + goto fail_get_ordinal; + wstats->discard.retries += tx_retry; */ + + return wstats; +} + + +/* net device stuff */ + +static inline void init_sys_config(struct ipw_sys_config *sys_config) +{ + memset(sys_config, 0, sizeof(struct ipw_sys_config)); + sys_config->bt_coexistence = 1; /* We may need to look into prvStaBtConfig */ + sys_config->answer_broadcast_ssid_probe = 0; + sys_config->accept_all_data_frames = 0; + sys_config->accept_non_directed_frames = 1; + sys_config->exclude_unicast_unencrypted = 0; + sys_config->disable_unicast_decryption = 1; + sys_config->exclude_multicast_unencrypted = 0; + sys_config->disable_multicast_decryption = 1; + sys_config->antenna_diversity = CFG_SYS_ANTENNA_BOTH; + sys_config->pass_crc_to_host = 0; /* TODO: See if 1 gives us FCS */ + sys_config->dot11g_auto_detection = 0; + sys_config->enable_cts_to_self = 0; + sys_config->bt_coexist_collision_thr = 0; + sys_config->pass_noise_stats_to_host = 1; +} + +static int ipw_net_open(struct net_device *dev) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + IPW_DEBUG_INFO("dev->open\n"); + /* we should be verifying the device is ready to be opened */ + if (!(priv->status & STATUS_RF_KILL_MASK) && + (priv->status & STATUS_ASSOCIATED)) + netif_start_queue(dev); + return 0; +} + +static int ipw_net_stop(struct net_device *dev) +{ + IPW_DEBUG_INFO("dev->close\n"); + netif_stop_queue(dev); + return 0; +} + +/* +todo: + +modify to send one tfd per fragment instead of using chunking. otherwise +we need to heavily modify the ieee80211_skb_to_txb. +*/ + +static inline void ipw_tx_skb(struct ipw_priv *priv, struct ieee80211_txb *txb) +{ + struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) + txb->fragments[0]->data; + int i = 0; + struct tfd_frame *tfd; + struct clx2_tx_queue *txq = &priv->txq[0]; + struct clx2_queue *q = &txq->q; + u8 id, hdr_len, unicast; + u16 remaining_bytes; + + switch (priv->ieee->iw_mode) { + case IW_MODE_ADHOC: + hdr_len = IEEE80211_3ADDR_LEN; + unicast = !is_broadcast_ether_addr(hdr->addr1) && + !is_multicast_ether_addr(hdr->addr1); + id = ipw_find_station(priv, hdr->addr1); + if (id == IPW_INVALID_STATION) { + id = ipw_add_station(priv, hdr->addr1); + if (id == IPW_INVALID_STATION) { + IPW_WARNING("Attempt to send data to " + "invalid cell: " MAC_FMT "\n", + MAC_ARG(hdr->addr1)); + goto drop; + } + } + break; + + case IW_MODE_INFRA: + default: + unicast = !is_broadcast_ether_addr(hdr->addr3) && + !is_multicast_ether_addr(hdr->addr3); + hdr_len = IEEE80211_3ADDR_LEN; + id = 0; + break; + } + + tfd = &txq->bd[q->first_empty]; + txq->txb[q->first_empty] = txb; + memset(tfd, 0, sizeof(*tfd)); + tfd->u.data.station_number = id; + + tfd->control_flags.message_type = TX_FRAME_TYPE; + tfd->control_flags.control_bits = TFD_NEED_IRQ_MASK; + + tfd->u.data.cmd_id = DINO_CMD_TX; + tfd->u.data.len = txb->payload_size; + remaining_bytes = txb->payload_size; + if (unlikely(!unicast)) + tfd->u.data.tx_flags = DCT_FLAG_NO_WEP; + else + tfd->u.data.tx_flags = DCT_FLAG_NO_WEP | DCT_FLAG_ACK_REQD; + + if (priv->assoc_request.ieee_mode == IPW_B_MODE) + tfd->u.data.tx_flags_ext = DCT_FLAG_EXT_MODE_CCK; + else + tfd->u.data.tx_flags_ext = DCT_FLAG_EXT_MODE_OFDM; + + if (priv->config & CFG_PREAMBLE) + tfd->u.data.tx_flags |= DCT_FLAG_SHORT_PREMBL; + + memcpy(&tfd->u.data.tfd.tfd_24.mchdr, hdr, hdr_len); + + /* payload */ + tfd->u.data.num_chunks = min((u8)(NUM_TFD_CHUNKS - 2), txb->nr_frags); + for (i = 0; i < tfd->u.data.num_chunks; i++) { + IPW_DEBUG_TX("Dumping TX packet frag %i of %i (%d bytes):\n", + i, tfd->u.data.num_chunks, + txb->fragments[i]->len - hdr_len); + printk_buf(IPW_DL_TX, txb->fragments[i]->data + hdr_len, + txb->fragments[i]->len - hdr_len); + + tfd->u.data.chunk_ptr[i] = pci_map_single( + priv->pci_dev, txb->fragments[i]->data + hdr_len, + txb->fragments[i]->len - hdr_len, PCI_DMA_TODEVICE); + tfd->u.data.chunk_len[i] = txb->fragments[i]->len - hdr_len; + } + + if (i != txb->nr_frags) { + struct sk_buff *skb; + u16 remaining_bytes = 0; + int j; + + for (j = i; j < txb->nr_frags; j++) + remaining_bytes += txb->fragments[j]->len - hdr_len; + + printk(KERN_INFO "Trying to reallocate for %d bytes\n", + remaining_bytes); + skb = alloc_skb(remaining_bytes, GFP_ATOMIC); + if (skb != NULL) { + tfd->u.data.chunk_len[i] = remaining_bytes; + for (j = i; j < txb->nr_frags; j++) { + int size = txb->fragments[j]->len - hdr_len; + printk(KERN_INFO "Adding frag %d %d...\n", + j, size); + memcpy(skb_put(skb, size), + txb->fragments[j]->data + hdr_len, + size); + } + dev_kfree_skb_any(txb->fragments[i]); + txb->fragments[i] = skb; + tfd->u.data.chunk_ptr[i] = pci_map_single( + priv->pci_dev, skb->data, + tfd->u.data.chunk_len[i], PCI_DMA_TODEVICE); + tfd->u.data.num_chunks++; + } + } + + /* kick DMA */ + q->first_empty = ipw_queue_inc_wrap(q->first_empty, q->n_bd); + ipw_write32(priv, q->reg_w, q->first_empty); + + if (ipw_queue_space(q) < q->high_mark) + netif_stop_queue(priv->net_dev); + + return; + + drop: + IPW_DEBUG_DROP("Silently dropping Tx packet.\n"); + ieee80211_txb_free(txb); +} + +static int ipw_net_hard_start_xmit(struct ieee80211_txb *txb, + struct net_device *dev) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + unsigned long flags; + + IPW_DEBUG_TX("dev->xmit(%d bytes)\n", txb->payload_size); + + spin_lock_irqsave(&priv->lock, flags); + + if (!(priv->status & STATUS_ASSOCIATED)) { + IPW_DEBUG_INFO("Tx attempt while not associated.\n"); + priv->ieee->stats.tx_carrier_errors++; + netif_stop_queue(dev); + goto fail_unlock; + } + + ipw_tx_skb(priv, txb); + + spin_unlock_irqrestore(&priv->lock, flags); + return 0; + + fail_unlock: + spin_unlock_irqrestore(&priv->lock, flags); + return 1; +} + +static struct net_device_stats *ipw_net_get_stats(struct net_device *dev) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + priv->ieee->stats.tx_packets = priv->tx_packets; + priv->ieee->stats.rx_packets = priv->rx_packets; + return &priv->ieee->stats; +} + +static void ipw_net_set_multicast_list(struct net_device *dev) +{ + +} + +static int ipw_net_set_mac_address(struct net_device *dev, void *p) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + struct sockaddr *addr = p; + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + priv->config |= CFG_CUSTOM_MAC; + memcpy(priv->mac_addr, addr->sa_data, ETH_ALEN); + printk(KERN_INFO "%s: Setting MAC to " MAC_FMT "\n", + priv->net_dev->name, MAC_ARG(priv->mac_addr)); + ipw_adapter_restart(priv); + return 0; +} + +static void ipw_ethtool_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + struct ipw_priv *p = ieee80211_priv(dev); + char vers[64]; + char date[32]; + u32 len; + + strcpy(info->driver, DRV_NAME); + strcpy(info->version, DRV_VERSION); + + len = sizeof(vers); + ipw_get_ordinal(p, IPW_ORD_STAT_FW_VERSION, vers, &len); + len = sizeof(date); + ipw_get_ordinal(p, IPW_ORD_STAT_FW_DATE, date, &len); + + snprintf(info->fw_version, sizeof(info->fw_version),"%s (%s)", + vers, date); + strcpy(info->bus_info, pci_name(p->pci_dev)); + info->eedump_len = CX2_EEPROM_IMAGE_SIZE; +} + +static u32 ipw_ethtool_get_link(struct net_device *dev) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + return (priv->status & STATUS_ASSOCIATED) != 0; +} + +static int ipw_ethtool_get_eeprom_len(struct net_device *dev) +{ + return CX2_EEPROM_IMAGE_SIZE; +} + +static int ipw_ethtool_get_eeprom(struct net_device *dev, + struct ethtool_eeprom *eeprom, u8 *bytes) +{ + struct ipw_priv *p = ieee80211_priv(dev); + + if (eeprom->offset + eeprom->len > CX2_EEPROM_IMAGE_SIZE) + return -EINVAL; + + memcpy(bytes, &((u8 *)p->eeprom)[eeprom->offset], eeprom->len); + return 0; +} + +static int ipw_ethtool_set_eeprom(struct net_device *dev, + struct ethtool_eeprom *eeprom, u8 *bytes) +{ + struct ipw_priv *p = ieee80211_priv(dev); + int i; + + if (eeprom->offset + eeprom->len > CX2_EEPROM_IMAGE_SIZE) + return -EINVAL; + + memcpy(&((u8 *)p->eeprom)[eeprom->offset], bytes, eeprom->len); + for (i = IPW_EEPROM_DATA; + i < IPW_EEPROM_DATA + CX2_EEPROM_IMAGE_SIZE; + i++) + ipw_write8(p, i, p->eeprom[i]); + + return 0; +} + +static struct ethtool_ops ipw_ethtool_ops = { + .get_link = ipw_ethtool_get_link, + .get_drvinfo = ipw_ethtool_get_drvinfo, + .get_eeprom_len = ipw_ethtool_get_eeprom_len, + .get_eeprom = ipw_ethtool_get_eeprom, + .set_eeprom = ipw_ethtool_set_eeprom, +}; + +static irqreturn_t ipw_isr(int irq, void *data, struct pt_regs *regs) +{ + struct ipw_priv *priv = data; + u32 inta, inta_mask; + + if (!priv) + return IRQ_NONE; + + spin_lock(&priv->lock); + + if (!(priv->status & STATUS_INT_ENABLED)) { + /* Shared IRQ */ + goto none; + } + + inta = ipw_read32(priv, CX2_INTA_RW); + inta_mask = ipw_read32(priv, CX2_INTA_MASK_R); + + if (inta == 0xFFFFFFFF) { + /* Hardware disappeared */ + IPW_WARNING("IRQ INTA == 0xFFFFFFFF\n"); + goto none; + } + + if (!(inta & (CX2_INTA_MASK_ALL & inta_mask))) { + /* Shared interrupt */ + goto none; + } + + /* tell the device to stop sending interrupts */ + ipw_disable_interrupts(priv); + + /* ack current interrupts */ + inta &= (CX2_INTA_MASK_ALL & inta_mask); + ipw_write32(priv, CX2_INTA_RW, inta); + + /* Cache INTA value for our tasklet */ + priv->isr_inta = inta; + + tasklet_schedule(&priv->irq_tasklet); + + spin_unlock(&priv->lock); + + return IRQ_HANDLED; + none: + spin_unlock(&priv->lock); + return IRQ_NONE; +} + +static void ipw_rf_kill(void *adapter) +{ + struct ipw_priv *priv = adapter; + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + + if (rf_kill_active(priv)) { + IPW_DEBUG_RF_KILL("RF Kill active, rescheduling GPIO check\n"); + if (priv->workqueue) + queue_delayed_work(priv->workqueue, + &priv->rf_kill, 2 * HZ); + goto exit_unlock; + } + + /* RF Kill is now disabled, so bring the device back up */ + + if (!(priv->status & STATUS_RF_KILL_MASK)) { + IPW_DEBUG_RF_KILL("HW RF Kill no longer active, restarting " + "device\n"); + + /* we can not do an adapter restart while inside an irq lock */ + queue_work(priv->workqueue, &priv->adapter_restart); + } else + IPW_DEBUG_RF_KILL("HW RF Kill deactivated. SW RF Kill still " + "enabled\n"); + + exit_unlock: + spin_unlock_irqrestore(&priv->lock, flags); +} + +static int ipw_setup_deferred_work(struct ipw_priv *priv) +{ + int ret = 0; + +#ifdef CONFIG_SOFTWARE_SUSPEND2 + priv->workqueue = create_workqueue(DRV_NAME, 0); +#else + priv->workqueue = create_workqueue(DRV_NAME); +#endif + init_waitqueue_head(&priv->wait_command_queue); + + INIT_WORK(&priv->adhoc_check, ipw_adhoc_check, priv); + INIT_WORK(&priv->associate, ipw_associate, priv); + INIT_WORK(&priv->disassociate, ipw_disassociate, priv); + INIT_WORK(&priv->rx_replenish, ipw_rx_queue_replenish, priv); + INIT_WORK(&priv->adapter_restart, ipw_adapter_restart, priv); + INIT_WORK(&priv->rf_kill, ipw_rf_kill, priv); + INIT_WORK(&priv->up, (void (*)(void *))ipw_up, priv); + INIT_WORK(&priv->down, (void (*)(void *))ipw_down, priv); + INIT_WORK(&priv->request_scan, + (void (*)(void *))ipw_request_scan, priv); + INIT_WORK(&priv->gather_stats, + (void (*)(void *))ipw_gather_stats, priv); + INIT_WORK(&priv->abort_scan, (void (*)(void *))ipw_abort_scan, priv); + INIT_WORK(&priv->roam, ipw_roam, priv); + INIT_WORK(&priv->scan_check, ipw_scan_check, priv); + + tasklet_init(&priv->irq_tasklet, (void (*)(unsigned long)) + ipw_irq_tasklet, (unsigned long)priv); + + return ret; +} + + +static void shim__set_security(struct net_device *dev, + struct ieee80211_security *sec) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + int i; + + for (i = 0; i < 4; i++) { + if (sec->flags & (1 << i)) { + priv->sec.key_sizes[i] = sec->key_sizes[i]; + if (sec->key_sizes[i] == 0) + priv->sec.flags &= ~(1 << i); + else + memcpy(priv->sec.keys[i], sec->keys[i], + sec->key_sizes[i]); + priv->sec.flags |= (1 << i); + priv->status |= STATUS_SECURITY_UPDATED; + } + } + + if ((sec->flags & SEC_ACTIVE_KEY) && + priv->sec.active_key != sec->active_key) { + if (sec->active_key <= 3) { + priv->sec.active_key = sec->active_key; + priv->sec.flags |= SEC_ACTIVE_KEY; + } else + priv->sec.flags &= ~SEC_ACTIVE_KEY; + priv->status |= STATUS_SECURITY_UPDATED; + } + + if ((sec->flags & SEC_AUTH_MODE) && + (priv->sec.auth_mode != sec->auth_mode)) { + priv->sec.auth_mode = sec->auth_mode; + priv->sec.flags |= SEC_AUTH_MODE; + if (sec->auth_mode == WLAN_AUTH_SHARED_KEY) + priv->capability |= CAP_SHARED_KEY; + else + priv->capability &= ~CAP_SHARED_KEY; + priv->status |= STATUS_SECURITY_UPDATED; + } + + if (sec->flags & SEC_ENABLED && + priv->sec.enabled != sec->enabled) { + priv->sec.flags |= SEC_ENABLED; + priv->sec.enabled = sec->enabled; + priv->status |= STATUS_SECURITY_UPDATED; + if (sec->enabled) + priv->capability |= CAP_PRIVACY_ON; + else + priv->capability &= ~CAP_PRIVACY_ON; + } + + if (sec->flags & SEC_LEVEL && + priv->sec.level != sec->level) { + priv->sec.level = sec->level; + priv->sec.flags |= SEC_LEVEL; + priv->status |= STATUS_SECURITY_UPDATED; + } + + /* To match current functionality of ipw2100 (which works well w/ + * various supplicants, we don't force a disassociate if the + * privacy capability changes ... */ +#if 0 + if ((priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)) && + (((priv->assoc_request.capability & + WLAN_CAPABILITY_PRIVACY) && !sec->enabled) || + (!(priv->assoc_request.capability & + WLAN_CAPABILITY_PRIVACY) && sec->enabled))) { + IPW_DEBUG_ASSOC("Disassociating due to capability " + "change.\n"); + ipw_disassociate(priv); + } +#endif +} + +static int init_supported_rates(struct ipw_priv *priv, + struct ipw_supported_rates *rates) +{ + /* TODO: Mask out rates based on priv->rates_mask */ + + memset(rates, 0, sizeof(*rates)); + /* configure supported rates */ + switch (priv->ieee->freq_band) { + case IEEE80211_52GHZ_BAND: + rates->ieee_mode = IPW_A_MODE; + rates->purpose = IPW_RATE_CAPABILITIES; + ipw_add_ofdm_scan_rates(rates, IEEE80211_CCK_MODULATION, + IEEE80211_OFDM_DEFAULT_RATES_MASK); + break; + + default: /* Mixed or 2.4Ghz */ + rates->ieee_mode = IPW_G_MODE; + rates->purpose = IPW_RATE_CAPABILITIES; + ipw_add_cck_scan_rates(rates, IEEE80211_CCK_MODULATION, + IEEE80211_CCK_DEFAULT_RATES_MASK); + if (priv->ieee->modulation & IEEE80211_OFDM_MODULATION) { + ipw_add_ofdm_scan_rates(rates, IEEE80211_CCK_MODULATION, + IEEE80211_OFDM_DEFAULT_RATES_MASK); + } + break; + } + + return 0; +} + +static int ipw_config(struct ipw_priv *priv) +{ + int i; + struct ipw_tx_power tx_power; + + memset(&priv->sys_config, 0, sizeof(priv->sys_config)); + memset(&tx_power, 0, sizeof(tx_power)); + + /* This is only called from ipw_up, which resets/reloads the firmware + so, we don't need to first disable the card before we configure + it */ + + /* configure device for 'G' band */ + tx_power.ieee_mode = IPW_G_MODE; + tx_power.num_channels = 11; + for (i = 0; i < 11; i++) { + tx_power.channels_tx_power[i].channel_number = i + 1; + tx_power.channels_tx_power[i].tx_power = priv->tx_power; + } + if (ipw_send_tx_power(priv, &tx_power)) + goto error; + + /* configure device to also handle 'B' band */ + tx_power.ieee_mode = IPW_B_MODE; + if (ipw_send_tx_power(priv, &tx_power)) + goto error; + + /* initialize adapter address */ + if (ipw_send_adapter_address(priv, priv->net_dev->dev_addr)) + goto error; + + /* set basic system config settings */ + init_sys_config(&priv->sys_config); + if (ipw_send_system_config(priv, &priv->sys_config)) + goto error; + + init_supported_rates(priv, &priv->rates); + if (ipw_send_supported_rates(priv, &priv->rates)) + goto error; + + /* Set request-to-send threshold */ + if (priv->rts_threshold) { + if (ipw_send_rts_threshold(priv, priv->rts_threshold)) + goto error; + } + + if (ipw_set_random_seed(priv)) + goto error; + + /* final state transition to the RUN state */ + if (ipw_send_host_complete(priv)) + goto error; + + /* If configured to try and auto-associate, kick off a scan */ + if ((priv->config & CFG_ASSOCIATE) && ipw_request_scan(priv)) + goto error; + + return 0; + + error: + return -EIO; +} + +#define MAX_HW_RESTARTS 5 +static int ipw_up(struct ipw_priv *priv) +{ + int rc, i; + + if (priv->status & STATUS_EXIT_PENDING) + return -EIO; + + for (i = 0; i < MAX_HW_RESTARTS; i++ ) { + /* Load the microcode, firmware, and eeprom. + * Also start the clocks. */ + rc = ipw_load(priv); + if (rc) { + IPW_ERROR("Unable to load firmware: 0x%08X\n", + rc); + return rc; + } + + ipw_init_ordinals(priv); + if (!(priv->config & CFG_CUSTOM_MAC)) + eeprom_parse_mac(priv, priv->mac_addr); + memcpy(priv->net_dev->dev_addr, priv->mac_addr, ETH_ALEN); + + if (priv->status & STATUS_RF_KILL_MASK) + return 0; + + rc = ipw_config(priv); + if (!rc) { + IPW_DEBUG_INFO("Configured device on count %i\n", i); + priv->notif_missed_beacons = 0; + netif_start_queue(priv->net_dev); + return 0; + } else { + IPW_DEBUG_INFO("Device configuration failed: 0x%08X\n", + rc); + } + + IPW_DEBUG_INFO("Failed to config device on retry %d of %d\n", + i, MAX_HW_RESTARTS); + + /* We had an error bringing up the hardware, so take it + * all the way back down so we can try again */ + ipw_down(priv); + } + + /* tried to restart and config the device for as long as our + * patience could withstand */ + IPW_ERROR("Unable to initialize device after %d attempts.\n", + i); + return -EIO; +} + +static void ipw_down(struct ipw_priv *priv) +{ + /* Attempt to disable the card */ +#if 0 + ipw_send_card_disable(priv, 0); +#endif + + /* tell the device to stop sending interrupts */ + ipw_disable_interrupts(priv); + + /* Clear all bits but the RF Kill */ + priv->status &= STATUS_RF_KILL_MASK; + + netif_carrier_off(priv->net_dev); + netif_stop_queue(priv->net_dev); + + ipw_stop_nic(priv); +} + +/* Called by register_netdev() */ +static int ipw_net_init(struct net_device *dev) +{ + struct ipw_priv *priv = ieee80211_priv(dev); + + if (priv->status & STATUS_RF_KILL_SW) { + IPW_WARNING("Radio disabled by module parameter.\n"); + return 0; + } else if (rf_kill_active(priv)) { + IPW_WARNING("Radio Frequency Kill Switch is On:\n" + "Kill switch must be turned off for " + "wireless networking to work.\n"); + queue_delayed_work(priv->workqueue, &priv->rf_kill, 2 * HZ); + return 0; + } + + if (ipw_up(priv)) + return -EIO; + + return 0; +} + +/* PCI driver stuff */ +static struct pci_device_id card_ids[] = { + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2701, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2702, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2711, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2712, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2721, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2722, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2731, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2732, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2741, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x103c, 0x2741, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2742, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2751, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2752, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2753, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2754, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2761, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x1043, 0x8086, 0x2762, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x104f, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + {PCI_VENDOR_ID_INTEL, 0x4220, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, /* BG */ + {PCI_VENDOR_ID_INTEL, 0x4221, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, /* 2225BG */ + {PCI_VENDOR_ID_INTEL, 0x4223, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, /* ABG */ + {PCI_VENDOR_ID_INTEL, 0x4224, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, /* ABG */ + + /* required last entry */ + {0,} +}; + +MODULE_DEVICE_TABLE(pci, card_ids); + +static struct attribute *ipw_sysfs_entries[] = { + &dev_attr_rf_kill.attr, + &dev_attr_direct_dword.attr, + &dev_attr_indirect_byte.attr, + &dev_attr_indirect_dword.attr, + &dev_attr_mem_gpio_reg.attr, + &dev_attr_command_event_reg.attr, + &dev_attr_nic_type.attr, + &dev_attr_status.attr, + &dev_attr_cfg.attr, + &dev_attr_dump_errors.attr, + &dev_attr_dump_events.attr, + &dev_attr_eeprom_delay.attr, + &dev_attr_ucode_version.attr, + &dev_attr_rtc.attr, + NULL +}; + +static struct attribute_group ipw_attribute_group = { + .name = NULL, /* put in device directory */ + .attrs = ipw_sysfs_entries, +}; + +static int ipw_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + int err = 0; + struct net_device *net_dev; + void __iomem *base; + u32 length, val; + struct ipw_priv *priv; + int band, modulation; + + net_dev = alloc_ieee80211(sizeof(struct ipw_priv)); + if (net_dev == NULL) { + err = -ENOMEM; + goto out; + } + + priv = ieee80211_priv(net_dev); + priv->ieee = netdev_priv(net_dev); + priv->net_dev = net_dev; + priv->pci_dev = pdev; +#ifdef CONFIG_IPW_DEBUG + ipw_debug_level = debug; +#endif + spin_lock_init(&priv->lock); + + if (pci_enable_device(pdev)) { + err = -ENODEV; + goto out_free_ieee80211; + } + + pci_set_master(pdev); + +#define PCI_DMA_32BIT 0x00000000ffffffffULL + err = pci_set_dma_mask(pdev, PCI_DMA_32BIT); + if (!err) + err = pci_set_consistent_dma_mask(pdev, PCI_DMA_32BIT); + if (err) { + printk(KERN_WARNING DRV_NAME ": No suitable DMA available.\n"); + goto out_pci_disable_device; + } + + pci_set_drvdata(pdev, priv); + + err = pci_request_regions(pdev, DRV_NAME); + if (err) + goto out_pci_disable_device; + + /* We disable the RETRY_TIMEOUT register (0x41) to keep + * PCI Tx retries from interfering with C3 CPU state */ + pci_read_config_dword(pdev, 0x40, &val); + if ((val & 0x0000ff00) != 0) + pci_write_config_dword(pdev, 0x40, val & 0xffff00ff); + + length = pci_resource_len(pdev, 0); + priv->hw_len = length; + + base = ioremap_nocache(pci_resource_start(pdev, 0), length); + if (!base) { + err = -ENODEV; + goto out_pci_release_regions; + } + + priv->hw_base = base; + IPW_DEBUG_INFO("pci_resource_len = 0x%08x\n", length); + IPW_DEBUG_INFO("pci_resource_base = %p\n", base); + + err = ipw_setup_deferred_work(priv); + if (err) { + IPW_ERROR("Unable to setup deferred work\n"); + goto out_iounmap; + } + + /* Initialize module parameter values here */ + if (ifname) + strncpy(net_dev->name, ifname, IFNAMSIZ); + + if (associate) + priv->config |= CFG_ASSOCIATE; + else + IPW_DEBUG_INFO("Auto associate disabled.\n"); + + if (auto_create) + priv->config |= CFG_ADHOC_CREATE; + else + IPW_DEBUG_INFO("Auto adhoc creation disabled.\n"); + + if (disable) { + priv->status |= STATUS_RF_KILL_SW; + IPW_DEBUG_INFO("Radio disabled.\n"); + } + + if (channel != 0) { + priv->config |= CFG_STATIC_CHANNEL; + priv->channel = channel; + IPW_DEBUG_INFO("Bind to static channel %d\n", channel); + IPW_DEBUG_INFO("Bind to static channel %d\n", channel); + /* TODO: Validate that provided channel is in range */ + } + + switch (mode) { + case 1: + priv->ieee->iw_mode = IW_MODE_ADHOC; + break; +#ifdef CONFIG_IPW_PROMISC + case 2: + priv->ieee->iw_mode = IW_MODE_MONITOR; + break; +#endif + default: + case 0: + priv->ieee->iw_mode = IW_MODE_INFRA; + break; + } + + if ((priv->pci_dev->device == 0x4223) || + (priv->pci_dev->device == 0x4224)) { + printk(KERN_INFO DRV_NAME + ": Detected Intel PRO/Wireless 2915ABG Network " + "Connection\n"); + priv->ieee->abg_ture = 1; + band = IEEE80211_52GHZ_BAND | IEEE80211_24GHZ_BAND; + modulation = IEEE80211_OFDM_MODULATION | + IEEE80211_CCK_MODULATION; + priv->adapter = IPW_2915ABG; + priv->ieee->mode = IEEE_A|IEEE_G|IEEE_B; + } else { + if (priv->pci_dev->device == 0x4221) + printk(KERN_INFO DRV_NAME + ": Detected Intel PRO/Wireless 2225BG Network " + "Connection\n"); + else + printk(KERN_INFO DRV_NAME + ": Detected Intel PRO/Wireless 2200BG Network " + "Connection\n"); + + priv->ieee->abg_ture = 0; + band = IEEE80211_24GHZ_BAND; + modulation = IEEE80211_OFDM_MODULATION | + IEEE80211_CCK_MODULATION; + priv->adapter = IPW_2200BG; + priv->ieee->mode = IEEE_G|IEEE_B; + } + + priv->ieee->freq_band = band; + priv->ieee->modulation = modulation; + + priv->rates_mask = IEEE80211_DEFAULT_RATES_MASK; + + priv->missed_beacon_threshold = IPW_MB_DISASSOCIATE_THRESHOLD_DEFAULT; + priv->roaming_threshold = IPW_MB_ROAMING_THRESHOLD_DEFAULT; + + priv->rts_threshold = DEFAULT_RTS_THRESHOLD; + + /* If power management is turned on, default to AC mode */ + priv->power_mode = IPW_POWER_AC; + priv->tx_power = IPW_DEFAULT_TX_POWER; + + err = request_irq(pdev->irq, ipw_isr, SA_SHIRQ, DRV_NAME, + priv); + if (err) { + IPW_ERROR("Error allocating IRQ %d\n", pdev->irq); + goto out_destroy_workqueue; + } + + SET_MODULE_OWNER(net_dev); + SET_NETDEV_DEV(net_dev, &pdev->dev); + + priv->ieee->hard_start_xmit = ipw_net_hard_start_xmit; + priv->ieee->set_security = shim__set_security; + + net_dev->open = ipw_net_open; + net_dev->stop = ipw_net_stop; + net_dev->init = ipw_net_init; + net_dev->get_stats = ipw_net_get_stats; + net_dev->set_multicast_list = ipw_net_set_multicast_list; + net_dev->set_mac_address = ipw_net_set_mac_address; + net_dev->get_wireless_stats = ipw_get_wireless_stats; + net_dev->wireless_handlers = &ipw_wx_handler_def; + net_dev->ethtool_ops = &ipw_ethtool_ops; + net_dev->irq = pdev->irq; + net_dev->base_addr = (unsigned long )priv->hw_base; + net_dev->mem_start = pci_resource_start(pdev, 0); + net_dev->mem_end = net_dev->mem_start + pci_resource_len(pdev, 0) - 1; + + err = sysfs_create_group(&pdev->dev.kobj, &ipw_attribute_group); + if (err) { + IPW_ERROR("failed to create sysfs device attributes\n"); + goto out_release_irq; + } + + err = register_netdev(net_dev); + if (err) { + IPW_ERROR("failed to register network device\n"); + goto out_remove_group; + } + + return 0; + + out_remove_group: + sysfs_remove_group(&pdev->dev.kobj, &ipw_attribute_group); + out_release_irq: + free_irq(pdev->irq, priv); + out_destroy_workqueue: + destroy_workqueue(priv->workqueue); + priv->workqueue = NULL; + out_iounmap: + iounmap(priv->hw_base); + out_pci_release_regions: + pci_release_regions(pdev); + out_pci_disable_device: + pci_disable_device(pdev); + pci_set_drvdata(pdev, NULL); + out_free_ieee80211: + free_ieee80211(priv->net_dev); + out: + return err; +} + +static void ipw_pci_remove(struct pci_dev *pdev) +{ + struct ipw_priv *priv = pci_get_drvdata(pdev); + if (!priv) + return; + + priv->status |= STATUS_EXIT_PENDING; + + sysfs_remove_group(&pdev->dev.kobj, &ipw_attribute_group); + + ipw_down(priv); + + unregister_netdev(priv->net_dev); + + if (priv->rxq) { + ipw_rx_queue_free(priv, priv->rxq); + priv->rxq = NULL; + } + ipw_tx_queue_free(priv); + + /* ipw_down will ensure that there is no more pending work + * in the workqueue's, so we can safely remove them now. */ + if (priv->workqueue) { + cancel_delayed_work(&priv->adhoc_check); + cancel_delayed_work(&priv->gather_stats); + cancel_delayed_work(&priv->request_scan); + cancel_delayed_work(&priv->rf_kill); + cancel_delayed_work(&priv->scan_check); + destroy_workqueue(priv->workqueue); + priv->workqueue = NULL; + } + + free_irq(pdev->irq, priv); + iounmap(priv->hw_base); + pci_release_regions(pdev); + pci_disable_device(pdev); + pci_set_drvdata(pdev, NULL); + free_ieee80211(priv->net_dev); + +#ifdef CONFIG_PM + if (fw_loaded) { + release_firmware(bootfw); + release_firmware(ucode); + release_firmware(firmware); + fw_loaded = 0; + } +#endif +} + + +#ifdef CONFIG_PM +static int ipw_pci_suspend(struct pci_dev *pdev, u32 state) +{ + struct ipw_priv *priv = pci_get_drvdata(pdev); + struct net_device *dev = priv->net_dev; + + printk(KERN_INFO "%s: Going into suspend...\n", dev->name); + + /* Take down the device; powers it off, etc. */ + ipw_down(priv); + + /* Remove the PRESENT state of the device */ + netif_device_detach(dev); + +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,10) + pci_save_state(pdev, priv->pm_state); +#else + pci_save_state(pdev); +#endif + pci_disable_device(pdev); + pci_set_power_state(pdev, state); + + return 0; +} + +static int ipw_pci_resume(struct pci_dev *pdev) +{ + struct ipw_priv *priv = pci_get_drvdata(pdev); + struct net_device *dev = priv->net_dev; + u32 val; + + printk(KERN_INFO "%s: Coming out of suspend...\n", dev->name); + + pci_set_power_state(pdev, 0); + pci_enable_device(pdev); +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,10) + pci_restore_state(pdev, priv->pm_state); +#else + pci_restore_state(pdev); +#endif + /* + * Suspend/Resume resets the PCI configuration space, so we have to + * re-disable the RETRY_TIMEOUT register (0x41) to keep PCI Tx retries + * from interfering with C3 CPU state. pci_restore_state won't help + * here since it only restores the first 64 bytes pci config header. + */ + pci_read_config_dword(pdev, 0x40, &val); + if ((val & 0x0000ff00) != 0) + pci_write_config_dword(pdev, 0x40, val & 0xffff00ff); + + /* Set the device back into the PRESENT state; this will also wake + * the queue of needed */ + netif_device_attach(dev); + + /* Bring the device back up */ + queue_work(priv->workqueue, &priv->up); + + return 0; +} +#endif + +/* driver initialization stuff */ +static struct pci_driver ipw_driver = { + .name = DRV_NAME, + .id_table = card_ids, + .probe = ipw_pci_probe, + .remove = __devexit_p(ipw_pci_remove), +#ifdef CONFIG_PM + .suspend = ipw_pci_suspend, + .resume = ipw_pci_resume, +#endif +}; + +static int __init ipw_init(void) +{ + int ret; + + printk(KERN_INFO DRV_NAME ": " DRV_DESCRIPTION ", " DRV_VERSION "\n"); + printk(KERN_INFO DRV_NAME ": " DRV_COPYRIGHT "\n"); + + ret = pci_module_init(&ipw_driver); + if (ret) { + IPW_ERROR("Unable to initialize PCI module\n"); + return ret; + } + + ret = driver_create_file(&ipw_driver.driver, + &driver_attr_debug_level); + if (ret) { + IPW_ERROR("Unable to create driver sysfs file\n"); + pci_unregister_driver(&ipw_driver); + return ret; + } + + return ret; +} + +static void __exit ipw_exit(void) +{ + driver_remove_file(&ipw_driver.driver, &driver_attr_debug_level); + pci_unregister_driver(&ipw_driver); +} + +module_param(disable, int, 0444); +MODULE_PARM_DESC(disable, "manually disable the radio (default 0 [radio on])"); + +module_param(associate, int, 0444); +MODULE_PARM_DESC(associate, "auto associate when scanning (default on)"); + +module_param(auto_create, int, 0444); +MODULE_PARM_DESC(auto_create, "auto create adhoc network (default on)"); + +module_param(debug, int, 0444); +MODULE_PARM_DESC(debug, "debug output mask"); + +module_param(channel, int, 0444); +MODULE_PARM_DESC(channel, "channel to limit associate to (default 0 [ANY])"); + +module_param(ifname, charp, 0444); +MODULE_PARM_DESC(ifname, "network device name (default eth%d)"); + +#ifdef CONFIG_IPW_PROMISC +module_param(mode, int, 0444); +MODULE_PARM_DESC(mode, "network mode (0=BSS,1=IBSS,2=Monitor)"); +#else +module_param(mode, int, 0444); +MODULE_PARM_DESC(mode, "network mode (0=BSS,1=IBSS)"); +#endif + +module_exit(ipw_exit); +module_init(ipw_init); diff --git a/drivers/net/wireless/ipw2200.h b/drivers/net/wireless/ipw2200.h new file mode 100644 index 000000000000..4e8b75e7962a --- /dev/null +++ b/drivers/net/wireless/ipw2200.h @@ -0,0 +1,1770 @@ +/****************************************************************************** + + Copyright(c) 2003 - 2004 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +******************************************************************************/ + +#ifndef __ipw2200_h__ +#define __ipw2200_h__ + +#define WEXT_USECHANNELS 1 + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/config.h> +#include <linux/init.h> + +#include <linux/version.h> +#include <linux/pci.h> +#include <linux/netdevice.h> +#include <linux/ethtool.h> +#include <linux/skbuff.h> +#include <linux/etherdevice.h> +#include <linux/delay.h> +#include <linux/random.h> + +#include <linux/firmware.h> +#include <linux/wireless.h> +#include <asm/io.h> + +#include <net/ieee80211.h> + +#define DRV_NAME "ipw2200" + +#include <linux/workqueue.h> + +#ifndef IRQ_NONE +typedef void irqreturn_t; +#define IRQ_NONE +#define IRQ_HANDLED +#define IRQ_RETVAL(x) +#endif + +#if ( LINUX_VERSION_CODE < KERNEL_VERSION(2,6,9) ) +#define __iomem +#endif + +#if ( LINUX_VERSION_CODE < KERNEL_VERSION(2,6,5) ) +#define pci_dma_sync_single_for_cpu pci_dma_sync_single +#define pci_dma_sync_single_for_device pci_dma_sync_single +#endif + +#ifndef HAVE_FREE_NETDEV +#define free_netdev(x) kfree(x) +#endif + +/* Authentication and Association States */ +enum connection_manager_assoc_states +{ + CMAS_INIT = 0, + CMAS_TX_AUTH_SEQ_1, + CMAS_RX_AUTH_SEQ_2, + CMAS_AUTH_SEQ_1_PASS, + CMAS_AUTH_SEQ_1_FAIL, + CMAS_TX_AUTH_SEQ_3, + CMAS_RX_AUTH_SEQ_4, + CMAS_AUTH_SEQ_2_PASS, + CMAS_AUTH_SEQ_2_FAIL, + CMAS_AUTHENTICATED, + CMAS_TX_ASSOC, + CMAS_RX_ASSOC_RESP, + CMAS_ASSOCIATED, + CMAS_LAST +}; + + +#define IPW_NORMAL 0 +#define IPW_NOWAIT 0 +#define IPW_WAIT (1<<0) +#define IPW_QUIET (1<<1) +#define IPW_ROAMING (1<<2) + +#define IPW_POWER_MODE_CAM 0x00 //(always on) +#define IPW_POWER_INDEX_1 0x01 +#define IPW_POWER_INDEX_2 0x02 +#define IPW_POWER_INDEX_3 0x03 +#define IPW_POWER_INDEX_4 0x04 +#define IPW_POWER_INDEX_5 0x05 +#define IPW_POWER_AC 0x06 +#define IPW_POWER_BATTERY 0x07 +#define IPW_POWER_LIMIT 0x07 +#define IPW_POWER_MASK 0x0F +#define IPW_POWER_ENABLED 0x10 +#define IPW_POWER_LEVEL(x) ((x) & IPW_POWER_MASK) + +#define IPW_CMD_HOST_COMPLETE 2 +#define IPW_CMD_POWER_DOWN 4 +#define IPW_CMD_SYSTEM_CONFIG 6 +#define IPW_CMD_MULTICAST_ADDRESS 7 +#define IPW_CMD_SSID 8 +#define IPW_CMD_ADAPTER_ADDRESS 11 +#define IPW_CMD_PORT_TYPE 12 +#define IPW_CMD_RTS_THRESHOLD 15 +#define IPW_CMD_FRAG_THRESHOLD 16 +#define IPW_CMD_POWER_MODE 17 +#define IPW_CMD_WEP_KEY 18 +#define IPW_CMD_TGI_TX_KEY 19 +#define IPW_CMD_SCAN_REQUEST 20 +#define IPW_CMD_ASSOCIATE 21 +#define IPW_CMD_SUPPORTED_RATES 22 +#define IPW_CMD_SCAN_ABORT 23 +#define IPW_CMD_TX_FLUSH 24 +#define IPW_CMD_QOS_PARAMETERS 25 +#define IPW_CMD_SCAN_REQUEST_EXT 26 +#define IPW_CMD_DINO_CONFIG 30 +#define IPW_CMD_RSN_CAPABILITIES 31 +#define IPW_CMD_RX_KEY 32 +#define IPW_CMD_CARD_DISABLE 33 +#define IPW_CMD_SEED_NUMBER 34 +#define IPW_CMD_TX_POWER 35 +#define IPW_CMD_COUNTRY_INFO 36 +#define IPW_CMD_AIRONET_INFO 37 +#define IPW_CMD_AP_TX_POWER 38 +#define IPW_CMD_CCKM_INFO 39 +#define IPW_CMD_CCX_VER_INFO 40 +#define IPW_CMD_SET_CALIBRATION 41 +#define IPW_CMD_SENSITIVITY_CALIB 42 +#define IPW_CMD_RETRY_LIMIT 51 +#define IPW_CMD_IPW_PRE_POWER_DOWN 58 +#define IPW_CMD_VAP_BEACON_TEMPLATE 60 +#define IPW_CMD_VAP_DTIM_PERIOD 61 +#define IPW_CMD_EXT_SUPPORTED_RATES 62 +#define IPW_CMD_VAP_LOCAL_TX_PWR_CONSTRAINT 63 +#define IPW_CMD_VAP_QUIET_INTERVALS 64 +#define IPW_CMD_VAP_CHANNEL_SWITCH 65 +#define IPW_CMD_VAP_MANDATORY_CHANNELS 66 +#define IPW_CMD_VAP_CELL_PWR_LIMIT 67 +#define IPW_CMD_VAP_CF_PARAM_SET 68 +#define IPW_CMD_VAP_SET_BEACONING_STATE 69 +#define IPW_CMD_MEASUREMENT 80 +#define IPW_CMD_POWER_CAPABILITY 81 +#define IPW_CMD_SUPPORTED_CHANNELS 82 +#define IPW_CMD_TPC_REPORT 83 +#define IPW_CMD_WME_INFO 84 +#define IPW_CMD_PRODUCTION_COMMAND 85 +#define IPW_CMD_LINKSYS_EOU_INFO 90 + +#define RFD_SIZE 4 +#define NUM_TFD_CHUNKS 6 + +#define TX_QUEUE_SIZE 32 +#define RX_QUEUE_SIZE 32 + +#define DINO_CMD_WEP_KEY 0x08 +#define DINO_CMD_TX 0x0B +#define DCT_ANTENNA_A 0x01 +#define DCT_ANTENNA_B 0x02 + +#define IPW_A_MODE 0 +#define IPW_B_MODE 1 +#define IPW_G_MODE 2 + +/* + * TX Queue Flag Definitions + */ + +/* abort attempt if mgmt frame is rx'd */ +#define DCT_FLAG_ABORT_MGMT 0x01 + +/* require CTS */ +#define DCT_FLAG_CTS_REQUIRED 0x02 + +/* use short preamble */ +#define DCT_FLAG_SHORT_PREMBL 0x04 + +/* RTS/CTS first */ +#define DCT_FLAG_RTS_REQD 0x08 + +/* dont calculate duration field */ +#define DCT_FLAG_DUR_SET 0x10 + +/* even if MAC WEP set (allows pre-encrypt) */ +#define DCT_FLAG_NO_WEP 0x20 +#define IPW_ +/* overwrite TSF field */ +#define DCT_FLAG_TSF_REQD 0x40 + +/* ACK rx is expected to follow */ +#define DCT_FLAG_ACK_REQD 0x80 + +#define DCT_FLAG_EXT_MODE_CCK 0x01 +#define DCT_FLAG_EXT_MODE_OFDM 0x00 + + +#define TX_RX_TYPE_MASK 0xFF +#define TX_FRAME_TYPE 0x00 +#define TX_HOST_COMMAND_TYPE 0x01 +#define RX_FRAME_TYPE 0x09 +#define RX_HOST_NOTIFICATION_TYPE 0x03 +#define RX_HOST_CMD_RESPONSE_TYPE 0x04 +#define RX_TX_FRAME_RESPONSE_TYPE 0x05 +#define TFD_NEED_IRQ_MASK 0x04 + +#define HOST_CMD_DINO_CONFIG 30 + +#define HOST_NOTIFICATION_STATUS_ASSOCIATED 10 +#define HOST_NOTIFICATION_STATUS_AUTHENTICATE 11 +#define HOST_NOTIFICATION_STATUS_SCAN_CHANNEL_RESULT 12 +#define HOST_NOTIFICATION_STATUS_SCAN_COMPLETED 13 +#define HOST_NOTIFICATION_STATUS_FRAG_LENGTH 14 +#define HOST_NOTIFICATION_STATUS_LINK_DETERIORATION 15 +#define HOST_NOTIFICATION_DINO_CONFIG_RESPONSE 16 +#define HOST_NOTIFICATION_STATUS_BEACON_STATE 17 +#define HOST_NOTIFICATION_STATUS_TGI_TX_KEY 18 +#define HOST_NOTIFICATION_TX_STATUS 19 +#define HOST_NOTIFICATION_CALIB_KEEP_RESULTS 20 +#define HOST_NOTIFICATION_MEASUREMENT_STARTED 21 +#define HOST_NOTIFICATION_MEASUREMENT_ENDED 22 +#define HOST_NOTIFICATION_CHANNEL_SWITCHED 23 +#define HOST_NOTIFICATION_RX_DURING_QUIET_PERIOD 24 +#define HOST_NOTIFICATION_NOISE_STATS 25 +#define HOST_NOTIFICATION_S36_MEASUREMENT_ACCEPTED 30 +#define HOST_NOTIFICATION_S36_MEASUREMENT_REFUSED 31 + +#define HOST_NOTIFICATION_STATUS_BEACON_MISSING 1 +#define IPW_MB_DISASSOCIATE_THRESHOLD_DEFAULT 24 +#define IPW_MB_ROAMING_THRESHOLD_DEFAULT 8 +#define IPW_REAL_RATE_RX_PACKET_THRESHOLD 300 + +#define MACADRR_BYTE_LEN 6 + +#define DCR_TYPE_AP 0x01 +#define DCR_TYPE_WLAP 0x02 +#define DCR_TYPE_MU_ESS 0x03 +#define DCR_TYPE_MU_IBSS 0x04 +#define DCR_TYPE_MU_PIBSS 0x05 +#define DCR_TYPE_SNIFFER 0x06 +#define DCR_TYPE_MU_BSS DCR_TYPE_MU_ESS + +/** + * Generic queue structure + * + * Contains common data for Rx and Tx queues + */ +struct clx2_queue { + int n_bd; /**< number of BDs in this queue */ + int first_empty; /**< 1-st empty entry (index) */ + int last_used; /**< last used entry (index) */ + u32 reg_w; /**< 'write' reg (queue head), addr in domain 1 */ + u32 reg_r; /**< 'read' reg (queue tail), addr in domain 1 */ + dma_addr_t dma_addr; /**< physical addr for BD's */ + int low_mark; /**< low watermark, resume queue if free space more than this */ + int high_mark; /**< high watermark, stop queue if free space less than this */ +} __attribute__ ((packed)); + +struct machdr32 +{ + u16 frame_ctl; + u16 duration; // watch out for endians! + u8 addr1[ MACADRR_BYTE_LEN ]; + u8 addr2[ MACADRR_BYTE_LEN ]; + u8 addr3[ MACADRR_BYTE_LEN ]; + u16 seq_ctrl; // more endians! + u8 addr4[ MACADRR_BYTE_LEN ]; + u16 qos_ctrl; +} __attribute__ ((packed)) ; + +struct machdr30 +{ + u16 frame_ctl; + u16 duration; // watch out for endians! + u8 addr1[ MACADRR_BYTE_LEN ]; + u8 addr2[ MACADRR_BYTE_LEN ]; + u8 addr3[ MACADRR_BYTE_LEN ]; + u16 seq_ctrl; // more endians! + u8 addr4[ MACADRR_BYTE_LEN ]; +} __attribute__ ((packed)) ; + +struct machdr26 +{ + u16 frame_ctl; + u16 duration; // watch out for endians! + u8 addr1[ MACADRR_BYTE_LEN ]; + u8 addr2[ MACADRR_BYTE_LEN ]; + u8 addr3[ MACADRR_BYTE_LEN ]; + u16 seq_ctrl; // more endians! + u16 qos_ctrl; +} __attribute__ ((packed)) ; + +struct machdr24 +{ + u16 frame_ctl; + u16 duration; // watch out for endians! + u8 addr1[ MACADRR_BYTE_LEN ]; + u8 addr2[ MACADRR_BYTE_LEN ]; + u8 addr3[ MACADRR_BYTE_LEN ]; + u16 seq_ctrl; // more endians! +} __attribute__ ((packed)) ; + +// TX TFD with 32 byte MAC Header +struct tx_tfd_32 +{ + struct machdr32 mchdr; // 32 + u32 uivplaceholder[2]; // 8 +} __attribute__ ((packed)) ; + +// TX TFD with 30 byte MAC Header +struct tx_tfd_30 +{ + struct machdr30 mchdr; // 30 + u8 reserved[2]; // 2 + u32 uivplaceholder[2]; // 8 +} __attribute__ ((packed)) ; + +// tx tfd with 26 byte mac header +struct tx_tfd_26 +{ + struct machdr26 mchdr; // 26 + u8 reserved1[2]; // 2 + u32 uivplaceholder[2]; // 8 + u8 reserved2[4]; // 4 +} __attribute__ ((packed)) ; + +// tx tfd with 24 byte mac header +struct tx_tfd_24 +{ + struct machdr24 mchdr; // 24 + u32 uivplaceholder[2]; // 8 + u8 reserved[8]; // 8 +} __attribute__ ((packed)) ; + + +#define DCT_WEP_KEY_FIELD_LENGTH 16 + +struct tfd_command +{ + u8 index; + u8 length; + u16 reserved; + u8 payload[0]; +} __attribute__ ((packed)) ; + +struct tfd_data { + /* Header */ + u32 work_area_ptr; + u8 station_number; /* 0 for BSS */ + u8 reserved1; + u16 reserved2; + + /* Tx Parameters */ + u8 cmd_id; + u8 seq_num; + u16 len; + u8 priority; + u8 tx_flags; + u8 tx_flags_ext; + u8 key_index; + u8 wepkey[DCT_WEP_KEY_FIELD_LENGTH]; + u8 rate; + u8 antenna; + u16 next_packet_duration; + u16 next_frag_len; + u16 back_off_counter; //////txop; + u8 retrylimit; + u16 cwcurrent; + u8 reserved3; + + /* 802.11 MAC Header */ + union + { + struct tx_tfd_24 tfd_24; + struct tx_tfd_26 tfd_26; + struct tx_tfd_30 tfd_30; + struct tx_tfd_32 tfd_32; + } tfd; + + /* Payload DMA info */ + u32 num_chunks; + u32 chunk_ptr[NUM_TFD_CHUNKS]; + u16 chunk_len[NUM_TFD_CHUNKS]; +} __attribute__ ((packed)); + +struct txrx_control_flags +{ + u8 message_type; + u8 rx_seq_num; + u8 control_bits; + u8 reserved; +} __attribute__ ((packed)); + +#define TFD_SIZE 128 +#define TFD_CMD_IMMEDIATE_PAYLOAD_LENGTH (TFD_SIZE - sizeof(struct txrx_control_flags)) + +struct tfd_frame +{ + struct txrx_control_flags control_flags; + union { + struct tfd_data data; + struct tfd_command cmd; + u8 raw[TFD_CMD_IMMEDIATE_PAYLOAD_LENGTH]; + } u; +} __attribute__ ((packed)) ; + +typedef void destructor_func(const void*); + +/** + * Tx Queue for DMA. Queue consists of circular buffer of + * BD's and required locking structures. + */ +struct clx2_tx_queue { + struct clx2_queue q; + struct tfd_frame* bd; + struct ieee80211_txb **txb; +}; + +/* + * RX related structures and functions + */ +#define RX_FREE_BUFFERS 32 +#define RX_LOW_WATERMARK 8 + +#define SUP_RATE_11A_MAX_NUM_CHANNELS (8) +#define SUP_RATE_11B_MAX_NUM_CHANNELS (4) +#define SUP_RATE_11G_MAX_NUM_CHANNELS (12) + +// Used for passing to driver number of successes and failures per rate +struct rate_histogram +{ + union { + u32 a[SUP_RATE_11A_MAX_NUM_CHANNELS]; + u32 b[SUP_RATE_11B_MAX_NUM_CHANNELS]; + u32 g[SUP_RATE_11G_MAX_NUM_CHANNELS]; + } success; + union { + u32 a[SUP_RATE_11A_MAX_NUM_CHANNELS]; + u32 b[SUP_RATE_11B_MAX_NUM_CHANNELS]; + u32 g[SUP_RATE_11G_MAX_NUM_CHANNELS]; + } failed; +} __attribute__ ((packed)); + +/* statistics command response */ +struct ipw_cmd_stats { + u8 cmd_id; + u8 seq_num; + u16 good_sfd; + u16 bad_plcp; + u16 wrong_bssid; + u16 valid_mpdu; + u16 bad_mac_header; + u16 reserved_frame_types; + u16 rx_ina; + u16 bad_crc32; + u16 invalid_cts; + u16 invalid_acks; + u16 long_distance_ina_fina; + u16 dsp_silence_unreachable; + u16 accumulated_rssi; + u16 rx_ovfl_frame_tossed; + u16 rssi_silence_threshold; + u16 rx_ovfl_frame_supplied; + u16 last_rx_frame_signal; + u16 last_rx_frame_noise; + u16 rx_autodetec_no_ofdm; + u16 rx_autodetec_no_barker; + u16 reserved; +} __attribute__ ((packed)); + +struct notif_channel_result { + u8 channel_num; + struct ipw_cmd_stats stats; + u8 uReserved; +} __attribute__ ((packed)); + +struct notif_scan_complete { + u8 scan_type; + u8 num_channels; + u8 status; + u8 reserved; +} __attribute__ ((packed)); + +struct notif_frag_length { + u16 frag_length; + u16 reserved; +} __attribute__ ((packed)); + +struct notif_beacon_state { + u32 state; + u32 number; +} __attribute__ ((packed)); + +struct notif_tgi_tx_key { + u8 key_state; + u8 security_type; + u8 station_index; + u8 reserved; +} __attribute__ ((packed)); + +struct notif_link_deterioration { + struct ipw_cmd_stats stats; + u8 rate; + u8 modulation; + struct rate_histogram histogram; + u8 reserved1; + u16 reserved2; +} __attribute__ ((packed)); + +struct notif_association { + u8 state; +} __attribute__ ((packed)); + +struct notif_authenticate { + u8 state; + struct machdr24 addr; + u16 status; +} __attribute__ ((packed)); + +struct temperature +{ + s32 measured; + s32 active; +} __attribute__ ((packed)); + +struct notif_calibration { + u8 data[104]; +} __attribute__ ((packed)); + +struct notif_noise { + u32 value; +} __attribute__ ((packed)); + +struct ipw_rx_notification { + u8 reserved[8]; + u8 subtype; + u8 flags; + u16 size; + union { + struct notif_association assoc; + struct notif_authenticate auth; + struct notif_channel_result channel_result; + struct notif_scan_complete scan_complete; + struct notif_frag_length frag_len; + struct notif_beacon_state beacon_state; + struct notif_tgi_tx_key tgi_tx_key; + struct notif_link_deterioration link_deterioration; + struct notif_calibration calibration; + struct notif_noise noise; + u8 raw[0]; + } u; +} __attribute__ ((packed)); + +struct ipw_rx_frame { + u32 reserved1; + u8 parent_tsf[4]; // fw_use[0] is boolean for OUR_TSF_IS_GREATER + u8 received_channel; // The channel that this frame was received on. + // Note that for .11b this does not have to be + // the same as the channel that it was sent. + // Filled by LMAC + u8 frameStatus; + u8 rate; + u8 rssi; + u8 agc; + u8 rssi_dbm; + u16 signal; + u16 noise; + u8 antennaAndPhy; + u8 control; // control bit should be on in bg + u8 rtscts_rate; // rate of rts or cts (in rts cts sequence rate + // is identical) + u8 rtscts_seen; // 0x1 RTS seen ; 0x2 CTS seen + u16 length; + u8 data[0]; +} __attribute__ ((packed)); + +struct ipw_rx_header { + u8 message_type; + u8 rx_seq_num; + u8 control_bits; + u8 reserved; +} __attribute__ ((packed)); + +struct ipw_rx_packet +{ + struct ipw_rx_header header; + union { + struct ipw_rx_frame frame; + struct ipw_rx_notification notification; + } u; +} __attribute__ ((packed)); + +#define IPW_RX_NOTIFICATION_SIZE sizeof(struct ipw_rx_header) + 12 +#define IPW_RX_FRAME_SIZE sizeof(struct ipw_rx_header) + \ + sizeof(struct ipw_rx_frame) + +struct ipw_rx_mem_buffer { + dma_addr_t dma_addr; + struct ipw_rx_buffer *rxb; + struct sk_buff *skb; + struct list_head list; +}; /* Not transferred over network, so not __attribute__ ((packed)) */ + +struct ipw_rx_queue { + struct ipw_rx_mem_buffer pool[RX_QUEUE_SIZE + RX_FREE_BUFFERS]; + struct ipw_rx_mem_buffer *queue[RX_QUEUE_SIZE]; + u32 processed; /* Internal index to last handled Rx packet */ + u32 read; /* Shared index to newest available Rx buffer */ + u32 write; /* Shared index to oldest written Rx packet */ + u32 free_count;/* Number of pre-allocated buffers in rx_free */ + /* Each of these lists is used as a FIFO for ipw_rx_mem_buffers */ + struct list_head rx_free; /* Own an SKBs */ + struct list_head rx_used; /* No SKB allocated */ + spinlock_t lock; +}; /* Not transferred over network, so not __attribute__ ((packed)) */ + + +struct alive_command_responce { + u8 alive_command; + u8 sequence_number; + u16 software_revision; + u8 device_identifier; + u8 reserved1[5]; + u16 reserved2; + u16 reserved3; + u16 clock_settle_time; + u16 powerup_settle_time; + u16 reserved4; + u8 time_stamp[5]; /* month, day, year, hours, minutes */ + u8 ucode_valid; +} __attribute__ ((packed)); + +#define IPW_MAX_RATES 12 + +struct ipw_rates { + u8 num_rates; + u8 rates[IPW_MAX_RATES]; +} __attribute__ ((packed)); + +struct command_block +{ + unsigned int control; + u32 source_addr; + u32 dest_addr; + unsigned int status; +} __attribute__ ((packed)); + +#define CB_NUMBER_OF_ELEMENTS_SMALL 64 +struct fw_image_desc +{ + unsigned long last_cb_index; + unsigned long current_cb_index; + struct command_block cb_list[CB_NUMBER_OF_ELEMENTS_SMALL]; + void * v_addr; + unsigned long p_addr; + unsigned long len; +}; + +struct ipw_sys_config +{ + u8 bt_coexistence; + u8 reserved1; + u8 answer_broadcast_ssid_probe; + u8 accept_all_data_frames; + u8 accept_non_directed_frames; + u8 exclude_unicast_unencrypted; + u8 disable_unicast_decryption; + u8 exclude_multicast_unencrypted; + u8 disable_multicast_decryption; + u8 antenna_diversity; + u8 pass_crc_to_host; + u8 dot11g_auto_detection; + u8 enable_cts_to_self; + u8 enable_multicast_filtering; + u8 bt_coexist_collision_thr; + u8 reserved2; + u8 accept_all_mgmt_bcpr; + u8 accept_all_mgtm_frames; + u8 pass_noise_stats_to_host; + u8 reserved3; +} __attribute__ ((packed)); + +struct ipw_multicast_addr +{ + u8 num_of_multicast_addresses; + u8 reserved[3]; + u8 mac1[6]; + u8 mac2[6]; + u8 mac3[6]; + u8 mac4[6]; +} __attribute__ ((packed)); + +struct ipw_wep_key +{ + u8 cmd_id; + u8 seq_num; + u8 key_index; + u8 key_size; + u8 key[16]; +} __attribute__ ((packed)); + +struct ipw_tgi_tx_key +{ + u8 key_id; + u8 security_type; + u8 station_index; + u8 flags; + u8 key[16]; + u32 tx_counter[2]; +} __attribute__ ((packed)); + +#define IPW_SCAN_CHANNELS 54 + +struct ipw_scan_request +{ + u8 scan_type; + u16 dwell_time; + u8 channels_list[IPW_SCAN_CHANNELS]; + u8 channels_reserved[3]; +} __attribute__ ((packed)); + +enum { + IPW_SCAN_PASSIVE_TILL_FIRST_BEACON_SCAN = 0, + IPW_SCAN_PASSIVE_FULL_DWELL_SCAN, + IPW_SCAN_ACTIVE_DIRECT_SCAN, + IPW_SCAN_ACTIVE_BROADCAST_SCAN, + IPW_SCAN_ACTIVE_BROADCAST_AND_DIRECT_SCAN, + IPW_SCAN_TYPES +}; + +struct ipw_scan_request_ext +{ + u32 full_scan_index; + u8 channels_list[IPW_SCAN_CHANNELS]; + u8 scan_type[IPW_SCAN_CHANNELS / 2]; + u8 reserved; + u16 dwell_time[IPW_SCAN_TYPES]; +} __attribute__ ((packed)); + +extern inline u8 ipw_get_scan_type(struct ipw_scan_request_ext *scan, u8 index) +{ + if (index % 2) + return scan->scan_type[index / 2] & 0x0F; + else + return (scan->scan_type[index / 2] & 0xF0) >> 4; +} + +extern inline void ipw_set_scan_type(struct ipw_scan_request_ext *scan, + u8 index, u8 scan_type) +{ + if (index % 2) + scan->scan_type[index / 2] = + (scan->scan_type[index / 2] & 0xF0) | + (scan_type & 0x0F); + else + scan->scan_type[index / 2] = + (scan->scan_type[index / 2] & 0x0F) | + ((scan_type & 0x0F) << 4); +} + +struct ipw_associate +{ + u8 channel; + u8 auth_type:4, + auth_key:4; + u8 assoc_type; + u8 reserved; + u16 policy_support; + u8 preamble_length; + u8 ieee_mode; + u8 bssid[ETH_ALEN]; + u32 assoc_tsf_msw; + u32 assoc_tsf_lsw; + u16 capability; + u16 listen_interval; + u16 beacon_interval; + u8 dest[ETH_ALEN]; + u16 atim_window; + u8 smr; + u8 reserved1; + u16 reserved2; +} __attribute__ ((packed)); + +struct ipw_supported_rates +{ + u8 ieee_mode; + u8 num_rates; + u8 purpose; + u8 reserved; + u8 supported_rates[IPW_MAX_RATES]; +} __attribute__ ((packed)); + +struct ipw_rts_threshold +{ + u16 rts_threshold; + u16 reserved; +} __attribute__ ((packed)); + +struct ipw_frag_threshold +{ + u16 frag_threshold; + u16 reserved; +} __attribute__ ((packed)); + +struct ipw_retry_limit +{ + u8 short_retry_limit; + u8 long_retry_limit; + u16 reserved; +} __attribute__ ((packed)); + +struct ipw_dino_config +{ + u32 dino_config_addr; + u16 dino_config_size; + u8 dino_response; + u8 reserved; +} __attribute__ ((packed)); + +struct ipw_aironet_info +{ + u8 id; + u8 length; + u16 reserved; +} __attribute__ ((packed)); + +struct ipw_rx_key +{ + u8 station_index; + u8 key_type; + u8 key_id; + u8 key_flag; + u8 key[16]; + u8 station_address[6]; + u8 key_index; + u8 reserved; +} __attribute__ ((packed)); + +struct ipw_country_channel_info +{ + u8 first_channel; + u8 no_channels; + s8 max_tx_power; +} __attribute__ ((packed)); + +struct ipw_country_info +{ + u8 id; + u8 length; + u8 country_str[3]; + struct ipw_country_channel_info groups[7]; +} __attribute__ ((packed)); + +struct ipw_channel_tx_power +{ + u8 channel_number; + s8 tx_power; +} __attribute__ ((packed)); + +#define SCAN_ASSOCIATED_INTERVAL (HZ) +#define SCAN_INTERVAL (HZ / 10) +#define MAX_A_CHANNELS 37 +#define MAX_B_CHANNELS 14 + +struct ipw_tx_power +{ + u8 num_channels; + u8 ieee_mode; + struct ipw_channel_tx_power channels_tx_power[MAX_A_CHANNELS]; +} __attribute__ ((packed)); + +struct ipw_qos_parameters +{ + u16 cw_min[4]; + u16 cw_max[4]; + u8 aifs[4]; + u8 flag[4]; + u16 tx_op_limit[4]; +} __attribute__ ((packed)); + +struct ipw_rsn_capabilities +{ + u8 id; + u8 length; + u16 version; +} __attribute__ ((packed)); + +struct ipw_sensitivity_calib +{ + u16 beacon_rssi_raw; + u16 reserved; +} __attribute__ ((packed)); + +/** + * Host command structure. + * + * On input, the following fields should be filled: + * - cmd + * - len + * - status_len + * - param (if needed) + * + * On output, + * - \a status contains status; + * - \a param filled with status parameters. + */ +struct ipw_cmd { + u32 cmd; /**< Host command */ + u32 status; /**< Status */ + u32 status_len; /**< How many 32 bit parameters in the status */ + u32 len; /**< incoming parameters length, bytes */ + /** + * command parameters. + * There should be enough space for incoming and + * outcoming parameters. + * Incoming parameters listed 1-st, followed by outcoming params. + * nParams=(len+3)/4+status_len + */ + u32 param[0]; +} __attribute__ ((packed)); + +#define STATUS_HCMD_ACTIVE (1<<0) /**< host command in progress */ + +#define STATUS_INT_ENABLED (1<<1) +#define STATUS_RF_KILL_HW (1<<2) +#define STATUS_RF_KILL_SW (1<<3) +#define STATUS_RF_KILL_MASK (STATUS_RF_KILL_HW | STATUS_RF_KILL_SW) + +#define STATUS_INIT (1<<5) +#define STATUS_AUTH (1<<6) +#define STATUS_ASSOCIATED (1<<7) +#define STATUS_STATE_MASK (STATUS_INIT | STATUS_AUTH | STATUS_ASSOCIATED) + +#define STATUS_ASSOCIATING (1<<8) +#define STATUS_DISASSOCIATING (1<<9) +#define STATUS_ROAMING (1<<10) +#define STATUS_EXIT_PENDING (1<<11) +#define STATUS_DISASSOC_PENDING (1<<12) +#define STATUS_STATE_PENDING (1<<13) + +#define STATUS_SCAN_PENDING (1<<20) +#define STATUS_SCANNING (1<<21) +#define STATUS_SCAN_ABORTING (1<<22) + +#define STATUS_INDIRECT_BYTE (1<<28) /* sysfs entry configured for access */ +#define STATUS_INDIRECT_DWORD (1<<29) /* sysfs entry configured for access */ +#define STATUS_DIRECT_DWORD (1<<30) /* sysfs entry configured for access */ + +#define STATUS_SECURITY_UPDATED (1<<31) /* Security sync needed */ + +#define CFG_STATIC_CHANNEL (1<<0) /* Restrict assoc. to single channel */ +#define CFG_STATIC_ESSID (1<<1) /* Restrict assoc. to single SSID */ +#define CFG_STATIC_BSSID (1<<2) /* Restrict assoc. to single BSSID */ +#define CFG_CUSTOM_MAC (1<<3) +#define CFG_PREAMBLE (1<<4) +#define CFG_ADHOC_PERSIST (1<<5) +#define CFG_ASSOCIATE (1<<6) +#define CFG_FIXED_RATE (1<<7) +#define CFG_ADHOC_CREATE (1<<8) + +#define CAP_SHARED_KEY (1<<0) /* Off = OPEN */ +#define CAP_PRIVACY_ON (1<<1) /* Off = No privacy */ + +#define MAX_STATIONS 32 +#define IPW_INVALID_STATION (0xff) + +struct ipw_station_entry { + u8 mac_addr[ETH_ALEN]; + u8 reserved; + u8 support_mode; +}; + +#define AVG_ENTRIES 8 +struct average { + s16 entries[AVG_ENTRIES]; + u8 pos; + u8 init; + s32 sum; +}; + +struct ipw_priv { + /* ieee device used by generic ieee processing code */ + struct ieee80211_device *ieee; + struct ieee80211_security sec; + + /* spinlock */ + spinlock_t lock; + + /* basic pci-network driver stuff */ + struct pci_dev *pci_dev; + struct net_device *net_dev; + + /* pci hardware address support */ + void __iomem *hw_base; + unsigned long hw_len; + + struct fw_image_desc sram_desc; + + /* result of ucode download */ + struct alive_command_responce dino_alive; + + wait_queue_head_t wait_command_queue; + wait_queue_head_t wait_state; + + /* Rx and Tx DMA processing queues */ + struct ipw_rx_queue *rxq; + struct clx2_tx_queue txq_cmd; + struct clx2_tx_queue txq[4]; + u32 status; + u32 config; + u32 capability; + + u8 last_rx_rssi; + u8 last_noise; + struct average average_missed_beacons; + struct average average_rssi; + struct average average_noise; + u32 port_type; + int rx_bufs_min; /**< minimum number of bufs in Rx queue */ + int rx_pend_max; /**< maximum pending buffers for one IRQ */ + u32 hcmd_seq; /**< sequence number for hcmd */ + u32 missed_beacon_threshold; + u32 roaming_threshold; + + struct ipw_associate assoc_request; + struct ieee80211_network *assoc_network; + + unsigned long ts_scan_abort; + struct ipw_supported_rates rates; + struct ipw_rates phy[3]; /**< PHY restrictions, per band */ + struct ipw_rates supp; /**< software defined */ + struct ipw_rates extended; /**< use for corresp. IE, AP only */ + + struct notif_link_deterioration last_link_deterioration; /** for statistics */ + struct ipw_cmd* hcmd; /**< host command currently executed */ + + wait_queue_head_t hcmd_wq; /**< host command waits for execution */ + u32 tsf_bcn[2]; /**< TSF from latest beacon */ + + struct notif_calibration calib; /**< last calibration */ + + /* ordinal interface with firmware */ + u32 table0_addr; + u32 table0_len; + u32 table1_addr; + u32 table1_len; + u32 table2_addr; + u32 table2_len; + + /* context information */ + u8 essid[IW_ESSID_MAX_SIZE]; + u8 essid_len; + u8 nick[IW_ESSID_MAX_SIZE]; + u16 rates_mask; + u8 channel; + struct ipw_sys_config sys_config; + u32 power_mode; + u8 bssid[ETH_ALEN]; + u16 rts_threshold; + u8 mac_addr[ETH_ALEN]; + u8 num_stations; + u8 stations[MAX_STATIONS][ETH_ALEN]; + + u32 notif_missed_beacons; + + /* Statistics and counters normalized with each association */ + u32 last_missed_beacons; + u32 last_tx_packets; + u32 last_rx_packets; + u32 last_tx_failures; + u32 last_rx_err; + u32 last_rate; + + u32 missed_adhoc_beacons; + u32 missed_beacons; + u32 rx_packets; + u32 tx_packets; + u32 quality; + + /* eeprom */ + u8 eeprom[0x100]; /* 256 bytes of eeprom */ + int eeprom_delay; + + struct iw_statistics wstats; + + struct workqueue_struct *workqueue; + + struct work_struct adhoc_check; + struct work_struct associate; + struct work_struct disassociate; + struct work_struct rx_replenish; + struct work_struct request_scan; + struct work_struct adapter_restart; + struct work_struct rf_kill; + struct work_struct up; + struct work_struct down; + struct work_struct gather_stats; + struct work_struct abort_scan; + struct work_struct roam; + struct work_struct scan_check; + + struct tasklet_struct irq_tasklet; + + +#define IPW_2200BG 1 +#define IPW_2915ABG 2 + u8 adapter; + +#define IPW_DEFAULT_TX_POWER 0x14 + u8 tx_power; + +#ifdef CONFIG_PM + u32 pm_state[16]; +#endif + + /* network state */ + + /* Used to pass the current INTA value from ISR to Tasklet */ + u32 isr_inta; + + /* debugging info */ + u32 indirect_dword; + u32 direct_dword; + u32 indirect_byte; +}; /*ipw_priv */ + + +/* debug macros */ + +#ifdef CONFIG_IPW_DEBUG +#define IPW_DEBUG(level, fmt, args...) \ +do { if (ipw_debug_level & (level)) \ + printk(KERN_DEBUG DRV_NAME": %c %s " fmt, \ + in_interrupt() ? 'I' : 'U', __FUNCTION__ , ## args); } while (0) +#else +#define IPW_DEBUG(level, fmt, args...) do {} while (0) +#endif /* CONFIG_IPW_DEBUG */ + +/* + * To use the debug system; + * + * If you are defining a new debug classification, simply add it to the #define + * list here in the form of: + * + * #define IPW_DL_xxxx VALUE + * + * shifting value to the left one bit from the previous entry. xxxx should be + * the name of the classification (for example, WEP) + * + * You then need to either add a IPW_xxxx_DEBUG() macro definition for your + * classification, or use IPW_DEBUG(IPW_DL_xxxx, ...) whenever you want + * to send output to that classification. + * + * To add your debug level to the list of levels seen when you perform + * + * % cat /proc/net/ipw/debug_level + * + * you simply need to add your entry to the ipw_debug_levels array. + * + * If you do not see debug_level in /proc/net/ipw then you do not have + * CONFIG_IPW_DEBUG defined in your kernel configuration + * + */ + +#define IPW_DL_ERROR (1<<0) +#define IPW_DL_WARNING (1<<1) +#define IPW_DL_INFO (1<<2) +#define IPW_DL_WX (1<<3) +#define IPW_DL_HOST_COMMAND (1<<5) +#define IPW_DL_STATE (1<<6) + +#define IPW_DL_NOTIF (1<<10) +#define IPW_DL_SCAN (1<<11) +#define IPW_DL_ASSOC (1<<12) +#define IPW_DL_DROP (1<<13) +#define IPW_DL_IOCTL (1<<14) + +#define IPW_DL_MANAGE (1<<15) +#define IPW_DL_FW (1<<16) +#define IPW_DL_RF_KILL (1<<17) +#define IPW_DL_FW_ERRORS (1<<18) + + +#define IPW_DL_ORD (1<<20) + +#define IPW_DL_FRAG (1<<21) +#define IPW_DL_WEP (1<<22) +#define IPW_DL_TX (1<<23) +#define IPW_DL_RX (1<<24) +#define IPW_DL_ISR (1<<25) +#define IPW_DL_FW_INFO (1<<26) +#define IPW_DL_IO (1<<27) +#define IPW_DL_TRACE (1<<28) + +#define IPW_DL_STATS (1<<29) + + +#define IPW_ERROR(f, a...) printk(KERN_ERR DRV_NAME ": " f, ## a) +#define IPW_WARNING(f, a...) printk(KERN_WARNING DRV_NAME ": " f, ## a) +#define IPW_DEBUG_INFO(f, a...) IPW_DEBUG(IPW_DL_INFO, f, ## a) + +#define IPW_DEBUG_WX(f, a...) IPW_DEBUG(IPW_DL_WX, f, ## a) +#define IPW_DEBUG_SCAN(f, a...) IPW_DEBUG(IPW_DL_SCAN, f, ## a) +#define IPW_DEBUG_STATUS(f, a...) IPW_DEBUG(IPW_DL_STATUS, f, ## a) +#define IPW_DEBUG_TRACE(f, a...) IPW_DEBUG(IPW_DL_TRACE, f, ## a) +#define IPW_DEBUG_RX(f, a...) IPW_DEBUG(IPW_DL_RX, f, ## a) +#define IPW_DEBUG_TX(f, a...) IPW_DEBUG(IPW_DL_TX, f, ## a) +#define IPW_DEBUG_ISR(f, a...) IPW_DEBUG(IPW_DL_ISR, f, ## a) +#define IPW_DEBUG_MANAGEMENT(f, a...) IPW_DEBUG(IPW_DL_MANAGE, f, ## a) +#define IPW_DEBUG_WEP(f, a...) IPW_DEBUG(IPW_DL_WEP, f, ## a) +#define IPW_DEBUG_HC(f, a...) IPW_DEBUG(IPW_DL_HOST_COMMAND, f, ## a) +#define IPW_DEBUG_FRAG(f, a...) IPW_DEBUG(IPW_DL_FRAG, f, ## a) +#define IPW_DEBUG_FW(f, a...) IPW_DEBUG(IPW_DL_FW, f, ## a) +#define IPW_DEBUG_RF_KILL(f, a...) IPW_DEBUG(IPW_DL_RF_KILL, f, ## a) +#define IPW_DEBUG_DROP(f, a...) IPW_DEBUG(IPW_DL_DROP, f, ## a) +#define IPW_DEBUG_IO(f, a...) IPW_DEBUG(IPW_DL_IO, f, ## a) +#define IPW_DEBUG_ORD(f, a...) IPW_DEBUG(IPW_DL_ORD, f, ## a) +#define IPW_DEBUG_FW_INFO(f, a...) IPW_DEBUG(IPW_DL_FW_INFO, f, ## a) +#define IPW_DEBUG_NOTIF(f, a...) IPW_DEBUG(IPW_DL_NOTIF, f, ## a) +#define IPW_DEBUG_STATE(f, a...) IPW_DEBUG(IPW_DL_STATE | IPW_DL_ASSOC | IPW_DL_INFO, f, ## a) +#define IPW_DEBUG_ASSOC(f, a...) IPW_DEBUG(IPW_DL_ASSOC | IPW_DL_INFO, f, ## a) +#define IPW_DEBUG_STATS(f, a...) IPW_DEBUG(IPW_DL_STATS, f, ## a) + +#include <linux/ctype.h> + +/* +* Register bit definitions +*/ + +/* Dino control registers bits */ + +#define DINO_ENABLE_SYSTEM 0x80 +#define DINO_ENABLE_CS 0x40 +#define DINO_RXFIFO_DATA 0x01 +#define DINO_CONTROL_REG 0x00200000 + +#define CX2_INTA_RW 0x00000008 +#define CX2_INTA_MASK_R 0x0000000C +#define CX2_INDIRECT_ADDR 0x00000010 +#define CX2_INDIRECT_DATA 0x00000014 +#define CX2_AUTOINC_ADDR 0x00000018 +#define CX2_AUTOINC_DATA 0x0000001C +#define CX2_RESET_REG 0x00000020 +#define CX2_GP_CNTRL_RW 0x00000024 + +#define CX2_READ_INT_REGISTER 0xFF4 + +#define CX2_GP_CNTRL_BIT_INIT_DONE 0x00000004 + +#define CX2_REGISTER_DOMAIN1_END 0x00001000 +#define CX2_SRAM_READ_INT_REGISTER 0x00000ff4 + +#define CX2_SHARED_LOWER_BOUND 0x00000200 +#define CX2_INTERRUPT_AREA_LOWER_BOUND 0x00000f80 + +#define CX2_NIC_SRAM_LOWER_BOUND 0x00000000 +#define CX2_NIC_SRAM_UPPER_BOUND 0x00030000 + +#define CX2_BIT_INT_HOST_SRAM_READ_INT_REGISTER (1 << 29) +#define CX2_GP_CNTRL_BIT_CLOCK_READY 0x00000001 +#define CX2_GP_CNTRL_BIT_HOST_ALLOWS_STANDBY 0x00000002 + +/* + * RESET Register Bit Indexes + */ +#define CBD_RESET_REG_PRINCETON_RESET 0x00000001 /* Bit 0 (LSB) */ +#define CX2_RESET_REG_SW_RESET 0x00000080 /* Bit 7 */ +#define CX2_RESET_REG_MASTER_DISABLED 0x00000100 /* Bit 8 */ +#define CX2_RESET_REG_STOP_MASTER 0x00000200 /* Bit 9 */ +#define CX2_ARC_KESHET_CONFIG 0x08000000 /* Bit 27 */ +#define CX2_START_STANDBY 0x00000004 /* Bit 2 */ + +#define CX2_CSR_CIS_UPPER_BOUND 0x00000200 +#define CX2_DOMAIN_0_END 0x1000 +#define CLX_MEM_BAR_SIZE 0x1000 + +#define CX2_BASEBAND_CONTROL_STATUS 0X00200000 +#define CX2_BASEBAND_TX_FIFO_WRITE 0X00200004 +#define CX2_BASEBAND_RX_FIFO_READ 0X00200004 +#define CX2_BASEBAND_CONTROL_STORE 0X00200010 + +#define CX2_INTERNAL_CMD_EVENT 0X00300004 +#define CX2_BASEBAND_POWER_DOWN 0x00000001 + +#define CX2_MEM_HALT_AND_RESET 0x003000e0 + +/* defgroup bits_halt_reset MEM_HALT_AND_RESET register bits */ +#define CX2_BIT_HALT_RESET_ON 0x80000000 +#define CX2_BIT_HALT_RESET_OFF 0x00000000 + +#define CB_LAST_VALID 0x20000000 +#define CB_INT_ENABLED 0x40000000 +#define CB_VALID 0x80000000 +#define CB_SRC_LE 0x08000000 +#define CB_DEST_LE 0x04000000 +#define CB_SRC_AUTOINC 0x00800000 +#define CB_SRC_IO_GATED 0x00400000 +#define CB_DEST_AUTOINC 0x00080000 +#define CB_SRC_SIZE_LONG 0x00200000 +#define CB_DEST_SIZE_LONG 0x00020000 + + +/* DMA DEFINES */ + +#define DMA_CONTROL_SMALL_CB_CONST_VALUE 0x00540000 +#define DMA_CB_STOP_AND_ABORT 0x00000C00 +#define DMA_CB_START 0x00000100 + + +#define CX2_SHARED_SRAM_SIZE 0x00030000 +#define CX2_SHARED_SRAM_DMA_CONTROL 0x00027000 +#define CB_MAX_LENGTH 0x1FFF + +#define CX2_HOST_EEPROM_DATA_SRAM_SIZE 0xA18 +#define CX2_EEPROM_IMAGE_SIZE 0x100 + + +/* DMA defs */ +#define CX2_DMA_I_CURRENT_CB 0x003000D0 +#define CX2_DMA_O_CURRENT_CB 0x003000D4 +#define CX2_DMA_I_DMA_CONTROL 0x003000A4 +#define CX2_DMA_I_CB_BASE 0x003000A0 + +#define CX2_TX_CMD_QUEUE_BD_BASE (0x00000200) +#define CX2_TX_CMD_QUEUE_BD_SIZE (0x00000204) +#define CX2_TX_QUEUE_0_BD_BASE (0x00000208) +#define CX2_TX_QUEUE_0_BD_SIZE (0x0000020C) +#define CX2_TX_QUEUE_1_BD_BASE (0x00000210) +#define CX2_TX_QUEUE_1_BD_SIZE (0x00000214) +#define CX2_TX_QUEUE_2_BD_BASE (0x00000218) +#define CX2_TX_QUEUE_2_BD_SIZE (0x0000021C) +#define CX2_TX_QUEUE_3_BD_BASE (0x00000220) +#define CX2_TX_QUEUE_3_BD_SIZE (0x00000224) +#define CX2_RX_BD_BASE (0x00000240) +#define CX2_RX_BD_SIZE (0x00000244) +#define CX2_RFDS_TABLE_LOWER (0x00000500) + +#define CX2_TX_CMD_QUEUE_READ_INDEX (0x00000280) +#define CX2_TX_QUEUE_0_READ_INDEX (0x00000284) +#define CX2_TX_QUEUE_1_READ_INDEX (0x00000288) +#define CX2_TX_QUEUE_2_READ_INDEX (0x0000028C) +#define CX2_TX_QUEUE_3_READ_INDEX (0x00000290) +#define CX2_RX_READ_INDEX (0x000002A0) + +#define CX2_TX_CMD_QUEUE_WRITE_INDEX (0x00000F80) +#define CX2_TX_QUEUE_0_WRITE_INDEX (0x00000F84) +#define CX2_TX_QUEUE_1_WRITE_INDEX (0x00000F88) +#define CX2_TX_QUEUE_2_WRITE_INDEX (0x00000F8C) +#define CX2_TX_QUEUE_3_WRITE_INDEX (0x00000F90) +#define CX2_RX_WRITE_INDEX (0x00000FA0) + +/* + * EEPROM Related Definitions + */ + +#define IPW_EEPROM_DATA_SRAM_ADDRESS (CX2_SHARED_LOWER_BOUND + 0x814) +#define IPW_EEPROM_DATA_SRAM_SIZE (CX2_SHARED_LOWER_BOUND + 0x818) +#define IPW_EEPROM_LOAD_DISABLE (CX2_SHARED_LOWER_BOUND + 0x81C) +#define IPW_EEPROM_DATA (CX2_SHARED_LOWER_BOUND + 0x820) +#define IPW_EEPROM_UPPER_ADDRESS (CX2_SHARED_LOWER_BOUND + 0x9E0) + +#define IPW_STATION_TABLE_LOWER (CX2_SHARED_LOWER_BOUND + 0xA0C) +#define IPW_STATION_TABLE_UPPER (CX2_SHARED_LOWER_BOUND + 0xB0C) +#define IPW_REQUEST_ATIM (CX2_SHARED_LOWER_BOUND + 0xB0C) +#define IPW_ATIM_SENT (CX2_SHARED_LOWER_BOUND + 0xB10) +#define IPW_WHO_IS_AWAKE (CX2_SHARED_LOWER_BOUND + 0xB14) +#define IPW_DURING_ATIM_WINDOW (CX2_SHARED_LOWER_BOUND + 0xB18) + + +#define MSB 1 +#define LSB 0 +#define WORD_TO_BYTE(_word) ((_word) * sizeof(u16)) + +#define GET_EEPROM_ADDR(_wordoffset,_byteoffset) \ + ( WORD_TO_BYTE(_wordoffset) + (_byteoffset) ) + +/* EEPROM access by BYTE */ +#define EEPROM_PME_CAPABILITY (GET_EEPROM_ADDR(0x09,MSB)) /* 1 byte */ +#define EEPROM_MAC_ADDRESS (GET_EEPROM_ADDR(0x21,LSB)) /* 6 byte */ +#define EEPROM_VERSION (GET_EEPROM_ADDR(0x24,MSB)) /* 1 byte */ +#define EEPROM_NIC_TYPE (GET_EEPROM_ADDR(0x25,LSB)) /* 1 byte */ +#define EEPROM_SKU_CAPABILITY (GET_EEPROM_ADDR(0x25,MSB)) /* 1 byte */ +#define EEPROM_COUNTRY_CODE (GET_EEPROM_ADDR(0x26,LSB)) /* 3 bytes */ +#define EEPROM_IBSS_CHANNELS_BG (GET_EEPROM_ADDR(0x28,LSB)) /* 2 bytes */ +#define EEPROM_IBSS_CHANNELS_A (GET_EEPROM_ADDR(0x29,MSB)) /* 5 bytes */ +#define EEPROM_BSS_CHANNELS_BG (GET_EEPROM_ADDR(0x2c,LSB)) /* 2 bytes */ +#define EEPROM_HW_VERSION (GET_EEPROM_ADDR(0x72,LSB)) /* 2 bytes */ + +/* NIC type as found in the one byte EEPROM_NIC_TYPE offset*/ +#define EEPROM_NIC_TYPE_STANDARD 0 +#define EEPROM_NIC_TYPE_DELL 1 +#define EEPROM_NIC_TYPE_FUJITSU 2 +#define EEPROM_NIC_TYPE_IBM 3 +#define EEPROM_NIC_TYPE_HP 4 + +#define FW_MEM_REG_LOWER_BOUND 0x00300000 +#define FW_MEM_REG_EEPROM_ACCESS (FW_MEM_REG_LOWER_BOUND + 0x40) + +#define EEPROM_BIT_SK (1<<0) +#define EEPROM_BIT_CS (1<<1) +#define EEPROM_BIT_DI (1<<2) +#define EEPROM_BIT_DO (1<<4) + +#define EEPROM_CMD_READ 0x2 + +/* Interrupts masks */ +#define CX2_INTA_NONE 0x00000000 + +#define CX2_INTA_BIT_RX_TRANSFER 0x00000002 +#define CX2_INTA_BIT_STATUS_CHANGE 0x00000010 +#define CX2_INTA_BIT_BEACON_PERIOD_EXPIRED 0x00000020 + +//Inta Bits for CF +#define CX2_INTA_BIT_TX_CMD_QUEUE 0x00000800 +#define CX2_INTA_BIT_TX_QUEUE_1 0x00001000 +#define CX2_INTA_BIT_TX_QUEUE_2 0x00002000 +#define CX2_INTA_BIT_TX_QUEUE_3 0x00004000 +#define CX2_INTA_BIT_TX_QUEUE_4 0x00008000 + +#define CX2_INTA_BIT_SLAVE_MODE_HOST_CMD_DONE 0x00010000 + +#define CX2_INTA_BIT_PREPARE_FOR_POWER_DOWN 0x00100000 +#define CX2_INTA_BIT_POWER_DOWN 0x00200000 + +#define CX2_INTA_BIT_FW_INITIALIZATION_DONE 0x01000000 +#define CX2_INTA_BIT_FW_CARD_DISABLE_PHY_OFF_DONE 0x02000000 +#define CX2_INTA_BIT_RF_KILL_DONE 0x04000000 +#define CX2_INTA_BIT_FATAL_ERROR 0x40000000 +#define CX2_INTA_BIT_PARITY_ERROR 0x80000000 + +/* Interrupts enabled at init time. */ +#define CX2_INTA_MASK_ALL \ + (CX2_INTA_BIT_TX_QUEUE_1 | \ + CX2_INTA_BIT_TX_QUEUE_2 | \ + CX2_INTA_BIT_TX_QUEUE_3 | \ + CX2_INTA_BIT_TX_QUEUE_4 | \ + CX2_INTA_BIT_TX_CMD_QUEUE | \ + CX2_INTA_BIT_RX_TRANSFER | \ + CX2_INTA_BIT_FATAL_ERROR | \ + CX2_INTA_BIT_PARITY_ERROR | \ + CX2_INTA_BIT_STATUS_CHANGE | \ + CX2_INTA_BIT_FW_INITIALIZATION_DONE | \ + CX2_INTA_BIT_BEACON_PERIOD_EXPIRED | \ + CX2_INTA_BIT_SLAVE_MODE_HOST_CMD_DONE | \ + CX2_INTA_BIT_PREPARE_FOR_POWER_DOWN | \ + CX2_INTA_BIT_POWER_DOWN | \ + CX2_INTA_BIT_RF_KILL_DONE ) + +#define IPWSTATUS_ERROR_LOG (CX2_SHARED_LOWER_BOUND + 0x410) +#define IPW_EVENT_LOG (CX2_SHARED_LOWER_BOUND + 0x414) + +/* FW event log definitions */ +#define EVENT_ELEM_SIZE (3 * sizeof(u32)) +#define EVENT_START_OFFSET (1 * sizeof(u32) + 2 * sizeof(u16)) + +/* FW error log definitions */ +#define ERROR_ELEM_SIZE (7 * sizeof(u32)) +#define ERROR_START_OFFSET (1 * sizeof(u32)) + +enum { + IPW_FW_ERROR_OK = 0, + IPW_FW_ERROR_FAIL, + IPW_FW_ERROR_MEMORY_UNDERFLOW, + IPW_FW_ERROR_MEMORY_OVERFLOW, + IPW_FW_ERROR_BAD_PARAM, + IPW_FW_ERROR_BAD_CHECKSUM, + IPW_FW_ERROR_NMI_INTERRUPT, + IPW_FW_ERROR_BAD_DATABASE, + IPW_FW_ERROR_ALLOC_FAIL, + IPW_FW_ERROR_DMA_UNDERRUN, + IPW_FW_ERROR_DMA_STATUS, + IPW_FW_ERROR_DINOSTATUS_ERROR, + IPW_FW_ERROR_EEPROMSTATUS_ERROR, + IPW_FW_ERROR_SYSASSERT, + IPW_FW_ERROR_FATAL_ERROR +}; + +#define AUTH_OPEN 0 +#define AUTH_SHARED_KEY 1 +#define AUTH_IGNORE 3 + +#define HC_ASSOCIATE 0 +#define HC_REASSOCIATE 1 +#define HC_DISASSOCIATE 2 +#define HC_IBSS_START 3 +#define HC_IBSS_RECONF 4 +#define HC_DISASSOC_QUIET 5 + +#define IPW_RATE_CAPABILITIES 1 +#define IPW_RATE_CONNECT 0 + + +/* + * Rate values and masks + */ +#define IPW_TX_RATE_1MB 0x0A +#define IPW_TX_RATE_2MB 0x14 +#define IPW_TX_RATE_5MB 0x37 +#define IPW_TX_RATE_6MB 0x0D +#define IPW_TX_RATE_9MB 0x0F +#define IPW_TX_RATE_11MB 0x6E +#define IPW_TX_RATE_12MB 0x05 +#define IPW_TX_RATE_18MB 0x07 +#define IPW_TX_RATE_24MB 0x09 +#define IPW_TX_RATE_36MB 0x0B +#define IPW_TX_RATE_48MB 0x01 +#define IPW_TX_RATE_54MB 0x03 + +#define IPW_ORD_TABLE_ID_MASK 0x0000FF00 +#define IPW_ORD_TABLE_VALUE_MASK 0x000000FF + +#define IPW_ORD_TABLE_0_MASK 0x0000F000 +#define IPW_ORD_TABLE_1_MASK 0x0000F100 +#define IPW_ORD_TABLE_2_MASK 0x0000F200 +#define IPW_ORD_TABLE_3_MASK 0x0000F300 +#define IPW_ORD_TABLE_4_MASK 0x0000F400 +#define IPW_ORD_TABLE_5_MASK 0x0000F500 +#define IPW_ORD_TABLE_6_MASK 0x0000F600 +#define IPW_ORD_TABLE_7_MASK 0x0000F700 + +/* + * Table 0 Entries (all entries are 32 bits) + */ +enum { + IPW_ORD_STAT_TX_CURR_RATE = IPW_ORD_TABLE_0_MASK + 1, + IPW_ORD_STAT_FRAG_TRESHOLD, + IPW_ORD_STAT_RTS_THRESHOLD, + IPW_ORD_STAT_TX_HOST_REQUESTS, + IPW_ORD_STAT_TX_HOST_COMPLETE, + IPW_ORD_STAT_TX_DIR_DATA, + IPW_ORD_STAT_TX_DIR_DATA_B_1, + IPW_ORD_STAT_TX_DIR_DATA_B_2, + IPW_ORD_STAT_TX_DIR_DATA_B_5_5, + IPW_ORD_STAT_TX_DIR_DATA_B_11, + /* Hole */ + + + + + + + + IPW_ORD_STAT_TX_DIR_DATA_G_1 = IPW_ORD_TABLE_0_MASK + 19, + IPW_ORD_STAT_TX_DIR_DATA_G_2, + IPW_ORD_STAT_TX_DIR_DATA_G_5_5, + IPW_ORD_STAT_TX_DIR_DATA_G_6, + IPW_ORD_STAT_TX_DIR_DATA_G_9, + IPW_ORD_STAT_TX_DIR_DATA_G_11, + IPW_ORD_STAT_TX_DIR_DATA_G_12, + IPW_ORD_STAT_TX_DIR_DATA_G_18, + IPW_ORD_STAT_TX_DIR_DATA_G_24, + IPW_ORD_STAT_TX_DIR_DATA_G_36, + IPW_ORD_STAT_TX_DIR_DATA_G_48, + IPW_ORD_STAT_TX_DIR_DATA_G_54, + IPW_ORD_STAT_TX_NON_DIR_DATA, + IPW_ORD_STAT_TX_NON_DIR_DATA_B_1, + IPW_ORD_STAT_TX_NON_DIR_DATA_B_2, + IPW_ORD_STAT_TX_NON_DIR_DATA_B_5_5, + IPW_ORD_STAT_TX_NON_DIR_DATA_B_11, + /* Hole */ + + + + + + + + IPW_ORD_STAT_TX_NON_DIR_DATA_G_1 = IPW_ORD_TABLE_0_MASK + 44, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_2, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_5_5, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_6, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_9, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_11, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_12, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_18, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_24, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_36, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_48, + IPW_ORD_STAT_TX_NON_DIR_DATA_G_54, + IPW_ORD_STAT_TX_RETRY, + IPW_ORD_STAT_TX_FAILURE, + IPW_ORD_STAT_RX_ERR_CRC, + IPW_ORD_STAT_RX_ERR_ICV, + IPW_ORD_STAT_RX_NO_BUFFER, + IPW_ORD_STAT_FULL_SCANS, + IPW_ORD_STAT_PARTIAL_SCANS, + IPW_ORD_STAT_TGH_ABORTED_SCANS, + IPW_ORD_STAT_TX_TOTAL_BYTES, + IPW_ORD_STAT_CURR_RSSI_RAW, + IPW_ORD_STAT_RX_BEACON, + IPW_ORD_STAT_MISSED_BEACONS, + IPW_ORD_TABLE_0_LAST +}; + +#define IPW_RSSI_TO_DBM 112 + +/* Table 1 Entries + */ +enum { + IPW_ORD_TABLE_1_LAST = IPW_ORD_TABLE_1_MASK | 1, +}; + +/* + * Table 2 Entries + * + * FW_VERSION: 16 byte string + * FW_DATE: 16 byte string (only 14 bytes used) + * UCODE_VERSION: 4 byte version code + * UCODE_DATE: 5 bytes code code + * ADDAPTER_MAC: 6 byte MAC address + * RTC: 4 byte clock + */ +enum { + IPW_ORD_STAT_FW_VERSION = IPW_ORD_TABLE_2_MASK | 1, + IPW_ORD_STAT_FW_DATE, + IPW_ORD_STAT_UCODE_VERSION, + IPW_ORD_STAT_UCODE_DATE, + IPW_ORD_STAT_ADAPTER_MAC, + IPW_ORD_STAT_RTC, + IPW_ORD_TABLE_2_LAST +}; + +/* Table 3 */ +enum { + IPW_ORD_STAT_TX_PACKET = IPW_ORD_TABLE_3_MASK | 0, + IPW_ORD_STAT_TX_PACKET_FAILURE, + IPW_ORD_STAT_TX_PACKET_SUCCESS, + IPW_ORD_STAT_TX_PACKET_ABORTED, + IPW_ORD_TABLE_3_LAST +}; + +/* Table 4 */ +enum { + IPW_ORD_TABLE_4_LAST = IPW_ORD_TABLE_4_MASK +}; + +/* Table 5 */ +enum { + IPW_ORD_STAT_AVAILABLE_AP_COUNT = IPW_ORD_TABLE_5_MASK, + IPW_ORD_STAT_AP_ASSNS, + IPW_ORD_STAT_ROAM, + IPW_ORD_STAT_ROAM_CAUSE_MISSED_BEACONS, + IPW_ORD_STAT_ROAM_CAUSE_UNASSOC, + IPW_ORD_STAT_ROAM_CAUSE_RSSI, + IPW_ORD_STAT_ROAM_CAUSE_LINK_QUALITY, + IPW_ORD_STAT_ROAM_CAUSE_AP_LOAD_BALANCE, + IPW_ORD_STAT_ROAM_CAUSE_AP_NO_TX, + IPW_ORD_STAT_LINK_UP, + IPW_ORD_STAT_LINK_DOWN, + IPW_ORD_ANTENNA_DIVERSITY, + IPW_ORD_CURR_FREQ, + IPW_ORD_TABLE_5_LAST +}; + +/* Table 6 */ +enum { + IPW_ORD_COUNTRY_CODE = IPW_ORD_TABLE_6_MASK, + IPW_ORD_CURR_BSSID, + IPW_ORD_CURR_SSID, + IPW_ORD_TABLE_6_LAST +}; + +/* Table 7 */ +enum { + IPW_ORD_STAT_PERCENT_MISSED_BEACONS = IPW_ORD_TABLE_7_MASK, + IPW_ORD_STAT_PERCENT_TX_RETRIES, + IPW_ORD_STAT_PERCENT_LINK_QUALITY, + IPW_ORD_STAT_CURR_RSSI_DBM, + IPW_ORD_TABLE_7_LAST +}; + +#define IPW_ORDINALS_TABLE_LOWER (CX2_SHARED_LOWER_BOUND + 0x500) +#define IPW_ORDINALS_TABLE_0 (CX2_SHARED_LOWER_BOUND + 0x180) +#define IPW_ORDINALS_TABLE_1 (CX2_SHARED_LOWER_BOUND + 0x184) +#define IPW_ORDINALS_TABLE_2 (CX2_SHARED_LOWER_BOUND + 0x188) +#define IPW_MEM_FIXED_OVERRIDE (CX2_SHARED_LOWER_BOUND + 0x41C) + +struct ipw_fixed_rate { + u16 tx_rates; + u16 reserved; +} __attribute__ ((packed)); + +#define CX2_INDIRECT_ADDR_MASK (~0x3ul) + +struct host_cmd { + u8 cmd; + u8 len; + u16 reserved; + u32 param[TFD_CMD_IMMEDIATE_PAYLOAD_LENGTH]; +} __attribute__ ((packed)); + +#define CFG_BT_COEXISTENCE_MIN 0x00 +#define CFG_BT_COEXISTENCE_DEFER 0x02 +#define CFG_BT_COEXISTENCE_KILL 0x04 +#define CFG_BT_COEXISTENCE_WME_OVER_BT 0x08 +#define CFG_BT_COEXISTENCE_OOB 0x10 +#define CFG_BT_COEXISTENCE_MAX 0xFF +#define CFG_BT_COEXISTENCE_DEF 0x80 /* read Bt from EEPROM*/ + +#define CFG_CTS_TO_ITSELF_ENABLED_MIN 0x0 +#define CFG_CTS_TO_ITSELF_ENABLED_MAX 0x1 +#define CFG_CTS_TO_ITSELF_ENABLED_DEF CFG_CTS_TO_ITSELF_ENABLED_MIN + +#define CFG_SYS_ANTENNA_BOTH 0x000 +#define CFG_SYS_ANTENNA_A 0x001 +#define CFG_SYS_ANTENNA_B 0x003 + +/* + * The definitions below were lifted off the ipw2100 driver, which only + * supports 'b' mode, so I'm sure these are not exactly correct. + * + * Somebody fix these!! + */ +#define REG_MIN_CHANNEL 0 +#define REG_MAX_CHANNEL 14 + +#define REG_CHANNEL_MASK 0x00003FFF +#define IPW_IBSS_11B_DEFAULT_MASK 0x87ff + +static const long ipw_frequencies[] = { + 2412, 2417, 2422, 2427, + 2432, 2437, 2442, 2447, + 2452, 2457, 2462, 2467, + 2472, 2484 +}; + +#define FREQ_COUNT ARRAY_SIZE(ipw_frequencies) + +#define IPW_MAX_CONFIG_RETRIES 10 + +static inline u32 frame_hdr_len(struct ieee80211_hdr *hdr) +{ + u32 retval; + u16 fc; + + retval = sizeof(struct ieee80211_hdr); + fc = le16_to_cpu(hdr->frame_ctl); + + /* + * Function ToDS FromDS + * IBSS 0 0 + * To AP 1 0 + * From AP 0 1 + * WDS (bridge) 1 1 + * + * Only WDS frames use Address4 among them. --YZ + */ + if (!(fc & IEEE80211_FCTL_TODS) || !(fc & IEEE80211_FCTL_FROMDS)) + retval -= ETH_ALEN; + + return retval; +} + +#endif /* __ipw2200_h__ */ diff --git a/drivers/net/wireless/orinoco.c b/drivers/net/wireless/orinoco.c index a3a32430ae9d..b47684c3217e 100644 --- a/drivers/net/wireless/orinoco.c +++ b/drivers/net/wireless/orinoco.c @@ -464,6 +464,8 @@ #include <linux/etherdevice.h> #include <linux/wireless.h> +#include <net/ieee80211.h> + #include <asm/uaccess.h> #include <asm/io.h> #include <asm/system.h> @@ -471,7 +473,6 @@ #include "hermes.h" #include "hermes_rid.h" #include "orinoco.h" -#include "ieee802_11.h" /********************************************************************/ /* Module information */ @@ -509,7 +510,7 @@ MODULE_PARM_DESC(suppress_linkstatus, "Don't log link status changes"); /********************************************************************/ #define ORINOCO_MIN_MTU 256 -#define ORINOCO_MAX_MTU (IEEE802_11_DATA_LEN - ENCAPS_OVERHEAD) +#define ORINOCO_MAX_MTU (IEEE80211_DATA_LEN - ENCAPS_OVERHEAD) #define SYMBOL_MAX_VER_LEN (14) #define USER_BAP 0 @@ -760,7 +761,7 @@ static int orinoco_change_mtu(struct net_device *dev, int new_mtu) if ( (new_mtu < ORINOCO_MIN_MTU) || (new_mtu > ORINOCO_MAX_MTU) ) return -EINVAL; - if ( (new_mtu + ENCAPS_OVERHEAD + IEEE802_11_HLEN) > + if ( (new_mtu + ENCAPS_OVERHEAD + IEEE80211_HLEN) > (priv->nicbuf_size - ETH_HLEN) ) return -EINVAL; @@ -1104,7 +1105,7 @@ static void __orinoco_ev_rx(struct net_device *dev, hermes_t *hw) stats->rx_dropped++; goto drop; } - if (length > IEEE802_11_DATA_LEN) { + if (length > IEEE80211_DATA_LEN) { printk(KERN_WARNING "%s: Oversized frame received (%d bytes)\n", dev->name, length); stats->rx_length_errors++; @@ -2264,7 +2265,7 @@ static int orinoco_init(struct net_device *dev) /* No need to lock, the hw_unavailable flag is already set in * alloc_orinocodev() */ - priv->nicbuf_size = IEEE802_11_FRAME_LEN + ETH_HLEN; + priv->nicbuf_size = IEEE80211_FRAME_LEN + ETH_HLEN; /* Initialize the firmware */ err = hermes_init(hw); diff --git a/drivers/net/wireless/wl3501.h b/drivers/net/wireless/wl3501.h index 8636d9306785..b5719437e981 100644 --- a/drivers/net/wireless/wl3501.h +++ b/drivers/net/wireless/wl3501.h @@ -2,7 +2,7 @@ #define __WL3501_H__ #include <linux/spinlock.h> -#include "ieee802_11.h" +#include <net/ieee80211.h> /* define for WLA 2.0 */ #define WL3501_BLKSZ 256 @@ -548,7 +548,7 @@ struct wl3501_80211_tx_plcp_hdr { struct wl3501_80211_tx_hdr { struct wl3501_80211_tx_plcp_hdr pclp_hdr; - struct ieee802_11_hdr mac_hdr; + struct ieee80211_hdr mac_hdr; } __attribute__ ((packed)); /* diff --git a/include/linux/wireless.h b/include/linux/wireless.h index 2f51f2b6562e..ae485f9c916e 100644 --- a/include/linux/wireless.h +++ b/include/linux/wireless.h @@ -1,10 +1,10 @@ /* * This file define a set of standard wireless extensions * - * Version : 17 21.6.04 + * Version : 18 12.3.05 * * Authors : Jean Tourrilhes - HPL - <jt@hpl.hp.com> - * Copyright (c) 1997-2004 Jean Tourrilhes, All Rights Reserved. + * Copyright (c) 1997-2005 Jean Tourrilhes, All Rights Reserved. */ #ifndef _LINUX_WIRELESS_H @@ -82,7 +82,7 @@ * (there is some stuff that will be added in the future...) * I just plan to increment with each new version. */ -#define WIRELESS_EXT 17 +#define WIRELESS_EXT 18 /* * Changes : @@ -182,6 +182,21 @@ * - Document (struct iw_quality *)->updated, add new flags (INVALID) * - Wireless Event capability in struct iw_range * - Add support for relative TxPower (yick !) + * + * V17 to V18 (From Jouni Malinen <jkmaline@cc.hut.fi>) + * ---------- + * - Add support for WPA/WPA2 + * - Add extended encoding configuration (SIOCSIWENCODEEXT and + * SIOCGIWENCODEEXT) + * - Add SIOCSIWGENIE/SIOCGIWGENIE + * - Add SIOCSIWMLME + * - Add SIOCSIWPMKSA + * - Add struct iw_range bit field for supported encoding capabilities + * - Add optional scan request parameters for SIOCSIWSCAN + * - Add SIOCSIWAUTH/SIOCGIWAUTH for setting authentication and WPA + * related parameters (extensible up to 4096 parameter values) + * - Add wireless events: IWEVGENIE, IWEVMICHAELMICFAILURE, + * IWEVASSOCREQIE, IWEVASSOCRESPIE, IWEVPMKIDCAND */ /**************************** CONSTANTS ****************************/ @@ -256,6 +271,30 @@ #define SIOCSIWPOWER 0x8B2C /* set Power Management settings */ #define SIOCGIWPOWER 0x8B2D /* get Power Management settings */ +/* WPA : Generic IEEE 802.11 informatiom element (e.g., for WPA/RSN/WMM). + * This ioctl uses struct iw_point and data buffer that includes IE id and len + * fields. More than one IE may be included in the request. Setting the generic + * IE to empty buffer (len=0) removes the generic IE from the driver. Drivers + * are allowed to generate their own WPA/RSN IEs, but in these cases, drivers + * are required to report the used IE as a wireless event, e.g., when + * associating with an AP. */ +#define SIOCSIWGENIE 0x8B30 /* set generic IE */ +#define SIOCGIWGENIE 0x8B31 /* get generic IE */ + +/* WPA : IEEE 802.11 MLME requests */ +#define SIOCSIWMLME 0x8B16 /* request MLME operation; uses + * struct iw_mlme */ +/* WPA : Authentication mode parameters */ +#define SIOCSIWAUTH 0x8B32 /* set authentication mode params */ +#define SIOCGIWAUTH 0x8B33 /* get authentication mode params */ + +/* WPA : Extended version of encoding configuration */ +#define SIOCSIWENCODEEXT 0x8B34 /* set encoding token & mode */ +#define SIOCGIWENCODEEXT 0x8B35 /* get encoding token & mode */ + +/* WPA2 : PMKSA cache management */ +#define SIOCSIWPMKSA 0x8B36 /* PMKSA cache operation */ + /* -------------------- DEV PRIVATE IOCTL LIST -------------------- */ /* These 32 ioctl are wireless device private, for 16 commands. @@ -297,6 +336,34 @@ #define IWEVCUSTOM 0x8C02 /* Driver specific ascii string */ #define IWEVREGISTERED 0x8C03 /* Discovered a new node (AP mode) */ #define IWEVEXPIRED 0x8C04 /* Expired a node (AP mode) */ +#define IWEVGENIE 0x8C05 /* Generic IE (WPA, RSN, WMM, ..) + * (scan results); This includes id and + * length fields. One IWEVGENIE may + * contain more than one IE. Scan + * results may contain one or more + * IWEVGENIE events. */ +#define IWEVMICHAELMICFAILURE 0x8C06 /* Michael MIC failure + * (struct iw_michaelmicfailure) + */ +#define IWEVASSOCREQIE 0x8C07 /* IEs used in (Re)Association Request. + * The data includes id and length + * fields and may contain more than one + * IE. This event is required in + * Managed mode if the driver + * generates its own WPA/RSN IE. This + * should be sent just before + * IWEVREGISTERED event for the + * association. */ +#define IWEVASSOCRESPIE 0x8C08 /* IEs used in (Re)Association + * Response. The data includes id and + * length fields and may contain more + * than one IE. This may be sent + * between IWEVASSOCREQIE and + * IWEVREGISTERED events for the + * association. */ +#define IWEVPMKIDCAND 0x8C09 /* PMKID candidate for RSN + * pre-authentication + * (struct iw_pmkid_cand) */ #define IWEVFIRST 0x8C00 @@ -432,12 +499,94 @@ #define IW_SCAN_THIS_MODE 0x0020 /* Scan only this Mode */ #define IW_SCAN_ALL_RATE 0x0040 /* Scan all Bit-Rates */ #define IW_SCAN_THIS_RATE 0x0080 /* Scan only this Bit-Rate */ +/* struct iw_scan_req scan_type */ +#define IW_SCAN_TYPE_ACTIVE 0 +#define IW_SCAN_TYPE_PASSIVE 1 /* Maximum size of returned data */ #define IW_SCAN_MAX_DATA 4096 /* In bytes */ /* Max number of char in custom event - use multiple of them if needed */ #define IW_CUSTOM_MAX 256 /* In bytes */ +/* Generic information element */ +#define IW_GENERIC_IE_MAX 1024 + +/* MLME requests (SIOCSIWMLME / struct iw_mlme) */ +#define IW_MLME_DEAUTH 0 +#define IW_MLME_DISASSOC 1 + +/* SIOCSIWAUTH/SIOCGIWAUTH struct iw_param flags */ +#define IW_AUTH_INDEX 0x0FFF +#define IW_AUTH_FLAGS 0xF000 +/* SIOCSIWAUTH/SIOCGIWAUTH parameters (0 .. 4095) + * (IW_AUTH_INDEX mask in struct iw_param flags; this is the index of the + * parameter that is being set/get to; value will be read/written to + * struct iw_param value field) */ +#define IW_AUTH_WPA_VERSION 0 +#define IW_AUTH_CIPHER_PAIRWISE 1 +#define IW_AUTH_CIPHER_GROUP 2 +#define IW_AUTH_KEY_MGMT 3 +#define IW_AUTH_TKIP_COUNTERMEASURES 4 +#define IW_AUTH_DROP_UNENCRYPTED 5 +#define IW_AUTH_80211_AUTH_ALG 6 +#define IW_AUTH_WPA_ENABLED 7 +#define IW_AUTH_RX_UNENCRYPTED_EAPOL 8 +#define IW_AUTH_ROAMING_CONTROL 9 +#define IW_AUTH_PRIVACY_INVOKED 10 + +/* IW_AUTH_WPA_VERSION values (bit field) */ +#define IW_AUTH_WPA_VERSION_DISABLED 0x00000001 +#define IW_AUTH_WPA_VERSION_WPA 0x00000002 +#define IW_AUTH_WPA_VERSION_WPA2 0x00000004 + +/* IW_AUTH_PAIRWISE_CIPHER and IW_AUTH_GROUP_CIPHER values (bit field) */ +#define IW_AUTH_CIPHER_NONE 0x00000001 +#define IW_AUTH_CIPHER_WEP40 0x00000002 +#define IW_AUTH_CIPHER_TKIP 0x00000004 +#define IW_AUTH_CIPHER_CCMP 0x00000008 +#define IW_AUTH_CIPHER_WEP104 0x00000010 + +/* IW_AUTH_KEY_MGMT values (bit field) */ +#define IW_AUTH_KEY_MGMT_802_1X 1 +#define IW_AUTH_KEY_MGMT_PSK 2 + +/* IW_AUTH_80211_AUTH_ALG values (bit field) */ +#define IW_AUTH_ALG_OPEN_SYSTEM 0x00000001 +#define IW_AUTH_ALG_SHARED_KEY 0x00000002 +#define IW_AUTH_ALG_LEAP 0x00000004 + +/* IW_AUTH_ROAMING_CONTROL values */ +#define IW_AUTH_ROAMING_ENABLE 0 /* driver/firmware based roaming */ +#define IW_AUTH_ROAMING_DISABLE 1 /* user space program used for roaming + * control */ + +/* SIOCSIWENCODEEXT definitions */ +#define IW_ENCODE_SEQ_MAX_SIZE 8 +/* struct iw_encode_ext ->alg */ +#define IW_ENCODE_ALG_NONE 0 +#define IW_ENCODE_ALG_WEP 1 +#define IW_ENCODE_ALG_TKIP 2 +#define IW_ENCODE_ALG_CCMP 3 +/* struct iw_encode_ext ->ext_flags */ +#define IW_ENCODE_EXT_TX_SEQ_VALID 0x00000001 +#define IW_ENCODE_EXT_RX_SEQ_VALID 0x00000002 +#define IW_ENCODE_EXT_GROUP_KEY 0x00000004 +#define IW_ENCODE_EXT_SET_TX_KEY 0x00000008 + +/* IWEVMICHAELMICFAILURE : struct iw_michaelmicfailure ->flags */ +#define IW_MICFAILURE_KEY_ID 0x00000003 /* Key ID 0..3 */ +#define IW_MICFAILURE_GROUP 0x00000004 +#define IW_MICFAILURE_PAIRWISE 0x00000008 +#define IW_MICFAILURE_STAKEY 0x00000010 +#define IW_MICFAILURE_COUNT 0x00000060 /* 1 or 2 (0 = count not supported) + */ + +/* Bit field values for enc_capa in struct iw_range */ +#define IW_ENC_CAPA_WPA 0x00000001 +#define IW_ENC_CAPA_WPA2 0x00000002 +#define IW_ENC_CAPA_CIPHER_TKIP 0x00000004 +#define IW_ENC_CAPA_CIPHER_CCMP 0x00000008 + /* Event capability macros - in (struct iw_range *)->event_capa * Because we have more than 32 possible events, we use an array of * 32 bit bitmasks. Note : 32 bits = 0x20 = 2^5. */ @@ -546,6 +695,132 @@ struct iw_thrspy struct iw_quality high; /* High threshold */ }; +/* + * Optional data for scan request + * + * Note: these optional parameters are controlling parameters for the + * scanning behavior, these do not apply to getting scan results + * (SIOCGIWSCAN). Drivers are expected to keep a local BSS table and + * provide a merged results with all BSSes even if the previous scan + * request limited scanning to a subset, e.g., by specifying an SSID. + * Especially, scan results are required to include an entry for the + * current BSS if the driver is in Managed mode and associated with an AP. + */ +struct iw_scan_req +{ + __u8 scan_type; /* IW_SCAN_TYPE_{ACTIVE,PASSIVE} */ + __u8 essid_len; + __u8 num_channels; /* num entries in channel_list; + * 0 = scan all allowed channels */ + __u8 flags; /* reserved as padding; use zero, this may + * be used in the future for adding flags + * to request different scan behavior */ + struct sockaddr bssid; /* ff:ff:ff:ff:ff:ff for broadcast BSSID or + * individual address of a specific BSS */ + + /* + * Use this ESSID if IW_SCAN_THIS_ESSID flag is used instead of using + * the current ESSID. This allows scan requests for specific ESSID + * without having to change the current ESSID and potentially breaking + * the current association. + */ + __u8 essid[IW_ESSID_MAX_SIZE]; + + /* + * Optional parameters for changing the default scanning behavior. + * These are based on the MLME-SCAN.request from IEEE Std 802.11. + * TU is 1.024 ms. If these are set to 0, driver is expected to use + * reasonable default values. min_channel_time defines the time that + * will be used to wait for the first reply on each channel. If no + * replies are received, next channel will be scanned after this. If + * replies are received, total time waited on the channel is defined by + * max_channel_time. + */ + __u32 min_channel_time; /* in TU */ + __u32 max_channel_time; /* in TU */ + + struct iw_freq channel_list[IW_MAX_FREQUENCIES]; +}; + +/* ------------------------- WPA SUPPORT ------------------------- */ + +/* + * Extended data structure for get/set encoding (this is used with + * SIOCSIWENCODEEXT/SIOCGIWENCODEEXT. struct iw_point and IW_ENCODE_* + * flags are used in the same way as with SIOCSIWENCODE/SIOCGIWENCODE and + * only the data contents changes (key data -> this structure, including + * key data). + * + * If the new key is the first group key, it will be set as the default + * TX key. Otherwise, default TX key index is only changed if + * IW_ENCODE_EXT_SET_TX_KEY flag is set. + * + * Key will be changed with SIOCSIWENCODEEXT in all cases except for + * special "change TX key index" operation which is indicated by setting + * key_len = 0 and ext_flags |= IW_ENCODE_EXT_SET_TX_KEY. + * + * tx_seq/rx_seq are only used when respective + * IW_ENCODE_EXT_{TX,RX}_SEQ_VALID flag is set in ext_flags. Normal + * TKIP/CCMP operation is to set RX seq with SIOCSIWENCODEEXT and start + * TX seq from zero whenever key is changed. SIOCGIWENCODEEXT is normally + * used only by an Authenticator (AP or an IBSS station) to get the + * current TX sequence number. Using TX_SEQ_VALID for SIOCSIWENCODEEXT and + * RX_SEQ_VALID for SIOCGIWENCODEEXT are optional, but can be useful for + * debugging/testing. + */ +struct iw_encode_ext +{ + __u32 ext_flags; /* IW_ENCODE_EXT_* */ + __u8 tx_seq[IW_ENCODE_SEQ_MAX_SIZE]; /* LSB first */ + __u8 rx_seq[IW_ENCODE_SEQ_MAX_SIZE]; /* LSB first */ + struct sockaddr addr; /* ff:ff:ff:ff:ff:ff for broadcast/multicast + * (group) keys or unicast address for + * individual keys */ + __u16 alg; /* IW_ENCODE_ALG_* */ + __u16 key_len; + __u8 key[0]; +}; + +/* SIOCSIWMLME data */ +struct iw_mlme +{ + __u16 cmd; /* IW_MLME_* */ + __u16 reason_code; + struct sockaddr addr; +}; + +/* SIOCSIWPMKSA data */ +#define IW_PMKSA_ADD 1 +#define IW_PMKSA_REMOVE 2 +#define IW_PMKSA_FLUSH 3 + +#define IW_PMKID_LEN 16 + +struct iw_pmksa +{ + __u32 cmd; /* IW_PMKSA_* */ + struct sockaddr bssid; + __u8 pmkid[IW_PMKID_LEN]; +}; + +/* IWEVMICHAELMICFAILURE data */ +struct iw_michaelmicfailure +{ + __u32 flags; + struct sockaddr src_addr; + __u8 tsc[IW_ENCODE_SEQ_MAX_SIZE]; /* LSB first */ +}; + +/* IWEVPMKIDCAND data */ +#define IW_PMKID_CAND_PREAUTH 0x00000001 /* RNS pre-authentication enabled */ +struct iw_pmkid_cand +{ + __u32 flags; /* IW_PMKID_CAND_* */ + __u32 index; /* the smaller the index, the higher the + * priority */ + struct sockaddr bssid; +}; + /* ------------------------ WIRELESS STATS ------------------------ */ /* * Wireless statistics (used for /proc/net/wireless) @@ -725,6 +1000,8 @@ struct iw_range struct iw_freq freq[IW_MAX_FREQUENCIES]; /* list */ /* Note : this frequency list doesn't need to fit channel numbers, * because each entry contain its channel index */ + + __u32 enc_capa; /* IW_ENC_CAPA_* bit field */ }; /* diff --git a/include/net/ieee80211.h b/include/net/ieee80211.h new file mode 100644 index 000000000000..b1bfaf1084f4 --- /dev/null +++ b/include/net/ieee80211.h @@ -0,0 +1,887 @@ +/* + * Merged with mainline ieee80211.h in Aug 2004. Original ieee802_11 + * remains copyright by the original authors + * + * Portions of the merged code are based on Host AP (software wireless + * LAN access point) driver for Intersil Prism2/2.5/3. + * + * Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + * <jkmaline@cc.hut.fi> + * Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + * + * Adaption to a generic IEEE 802.11 stack by James Ketrenos + * <jketreno@linux.intel.com> + * Copyright (c) 2004, Intel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ +#ifndef IEEE80211_H +#define IEEE80211_H +#include <linux/if_ether.h> /* ETH_ALEN */ +#include <linux/kernel.h> /* ARRAY_SIZE */ + +#if WIRELESS_EXT < 17 +#define IW_QUAL_QUAL_INVALID 0x10 +#define IW_QUAL_LEVEL_INVALID 0x20 +#define IW_QUAL_NOISE_INVALID 0x40 +#define IW_QUAL_QUAL_UPDATED 0x1 +#define IW_QUAL_LEVEL_UPDATED 0x2 +#define IW_QUAL_NOISE_UPDATED 0x4 +#endif + +#define IEEE80211_DATA_LEN 2304 +/* Maximum size for the MA-UNITDATA primitive, 802.11 standard section + 6.2.1.1.2. + + The figure in section 7.1.2 suggests a body size of up to 2312 + bytes is allowed, which is a bit confusing, I suspect this + represents the 2304 bytes of real data, plus a possible 8 bytes of + WEP IV and ICV. (this interpretation suggested by Ramiro Barreiro) */ + + +#define IEEE80211_HLEN 30 +#define IEEE80211_FRAME_LEN (IEEE80211_DATA_LEN + IEEE80211_HLEN) + +struct ieee80211_hdr { + u16 frame_ctl; + u16 duration_id; + u8 addr1[ETH_ALEN]; + u8 addr2[ETH_ALEN]; + u8 addr3[ETH_ALEN]; + u16 seq_ctl; + u8 addr4[ETH_ALEN]; +} __attribute__ ((packed)); + +struct ieee80211_hdr_3addr { + u16 frame_ctl; + u16 duration_id; + u8 addr1[ETH_ALEN]; + u8 addr2[ETH_ALEN]; + u8 addr3[ETH_ALEN]; + u16 seq_ctl; +} __attribute__ ((packed)); + +enum eap_type { + EAP_PACKET = 0, + EAPOL_START, + EAPOL_LOGOFF, + EAPOL_KEY, + EAPOL_ENCAP_ASF_ALERT +}; + +static const char *eap_types[] = { + [EAP_PACKET] = "EAP-Packet", + [EAPOL_START] = "EAPOL-Start", + [EAPOL_LOGOFF] = "EAPOL-Logoff", + [EAPOL_KEY] = "EAPOL-Key", + [EAPOL_ENCAP_ASF_ALERT] = "EAPOL-Encap-ASF-Alert" +}; + +static inline const char *eap_get_type(int type) +{ + return (type >= ARRAY_SIZE(eap_types)) ? "Unknown" : eap_types[type]; +} + +struct eapol { + u8 snap[6]; + u16 ethertype; + u8 version; + u8 type; + u16 length; +} __attribute__ ((packed)); + +#define IEEE80211_3ADDR_LEN 24 +#define IEEE80211_4ADDR_LEN 30 +#define IEEE80211_FCS_LEN 4 + +#define MIN_FRAG_THRESHOLD 256U +#define MAX_FRAG_THRESHOLD 2346U + +/* Frame control field constants */ +#define IEEE80211_FCTL_VERS 0x0002 +#define IEEE80211_FCTL_FTYPE 0x000c +#define IEEE80211_FCTL_STYPE 0x00f0 +#define IEEE80211_FCTL_TODS 0x0100 +#define IEEE80211_FCTL_FROMDS 0x0200 +#define IEEE80211_FCTL_MOREFRAGS 0x0400 +#define IEEE80211_FCTL_RETRY 0x0800 +#define IEEE80211_FCTL_PM 0x1000 +#define IEEE80211_FCTL_MOREDATA 0x2000 +#define IEEE80211_FCTL_WEP 0x4000 +#define IEEE80211_FCTL_ORDER 0x8000 + +#define IEEE80211_FTYPE_MGMT 0x0000 +#define IEEE80211_FTYPE_CTL 0x0004 +#define IEEE80211_FTYPE_DATA 0x0008 + +/* management */ +#define IEEE80211_STYPE_ASSOC_REQ 0x0000 +#define IEEE80211_STYPE_ASSOC_RESP 0x0010 +#define IEEE80211_STYPE_REASSOC_REQ 0x0020 +#define IEEE80211_STYPE_REASSOC_RESP 0x0030 +#define IEEE80211_STYPE_PROBE_REQ 0x0040 +#define IEEE80211_STYPE_PROBE_RESP 0x0050 +#define IEEE80211_STYPE_BEACON 0x0080 +#define IEEE80211_STYPE_ATIM 0x0090 +#define IEEE80211_STYPE_DISASSOC 0x00A0 +#define IEEE80211_STYPE_AUTH 0x00B0 +#define IEEE80211_STYPE_DEAUTH 0x00C0 + +/* control */ +#define IEEE80211_STYPE_PSPOLL 0x00A0 +#define IEEE80211_STYPE_RTS 0x00B0 +#define IEEE80211_STYPE_CTS 0x00C0 +#define IEEE80211_STYPE_ACK 0x00D0 +#define IEEE80211_STYPE_CFEND 0x00E0 +#define IEEE80211_STYPE_CFENDACK 0x00F0 + +/* data */ +#define IEEE80211_STYPE_DATA 0x0000 +#define IEEE80211_STYPE_DATA_CFACK 0x0010 +#define IEEE80211_STYPE_DATA_CFPOLL 0x0020 +#define IEEE80211_STYPE_DATA_CFACKPOLL 0x0030 +#define IEEE80211_STYPE_NULLFUNC 0x0040 +#define IEEE80211_STYPE_CFACK 0x0050 +#define IEEE80211_STYPE_CFPOLL 0x0060 +#define IEEE80211_STYPE_CFACKPOLL 0x0070 + +#define IEEE80211_SCTL_FRAG 0x000F +#define IEEE80211_SCTL_SEQ 0xFFF0 + + +/* debug macros */ + +#ifdef CONFIG_IEEE80211_DEBUG +extern u32 ieee80211_debug_level; +#define IEEE80211_DEBUG(level, fmt, args...) \ +do { if (ieee80211_debug_level & (level)) \ + printk(KERN_DEBUG "ieee80211: %c %s " fmt, \ + in_interrupt() ? 'I' : 'U', __FUNCTION__ , ## args); } while (0) +#else +#define IEEE80211_DEBUG(level, fmt, args...) do {} while (0) +#endif /* CONFIG_IEEE80211_DEBUG */ + +/* + * To use the debug system; + * + * If you are defining a new debug classification, simply add it to the #define + * list here in the form of: + * + * #define IEEE80211_DL_xxxx VALUE + * + * shifting value to the left one bit from the previous entry. xxxx should be + * the name of the classification (for example, WEP) + * + * You then need to either add a IEEE80211_xxxx_DEBUG() macro definition for your + * classification, or use IEEE80211_DEBUG(IEEE80211_DL_xxxx, ...) whenever you want + * to send output to that classification. + * + * To add your debug level to the list of levels seen when you perform + * + * % cat /proc/net/ipw/debug_level + * + * you simply need to add your entry to the ipw_debug_levels array. + * + * If you do not see debug_level in /proc/net/ipw then you do not have + * CONFIG_IEEE80211_DEBUG defined in your kernel configuration + * + */ + +#define IEEE80211_DL_INFO (1<<0) +#define IEEE80211_DL_WX (1<<1) +#define IEEE80211_DL_SCAN (1<<2) +#define IEEE80211_DL_STATE (1<<3) +#define IEEE80211_DL_MGMT (1<<4) +#define IEEE80211_DL_FRAG (1<<5) +#define IEEE80211_DL_EAP (1<<6) +#define IEEE80211_DL_DROP (1<<7) + +#define IEEE80211_DL_TX (1<<8) +#define IEEE80211_DL_RX (1<<9) + +#define IEEE80211_ERROR(f, a...) printk(KERN_ERR "ieee80211: " f, ## a) +#define IEEE80211_WARNING(f, a...) printk(KERN_WARNING "ieee80211: " f, ## a) +#define IEEE80211_DEBUG_INFO(f, a...) IEEE80211_DEBUG(IEEE80211_DL_INFO, f, ## a) + +#define IEEE80211_DEBUG_WX(f, a...) IEEE80211_DEBUG(IEEE80211_DL_WX, f, ## a) +#define IEEE80211_DEBUG_SCAN(f, a...) IEEE80211_DEBUG(IEEE80211_DL_SCAN, f, ## a) +#define IEEE80211_DEBUG_STATE(f, a...) IEEE80211_DEBUG(IEEE80211_DL_STATE, f, ## a) +#define IEEE80211_DEBUG_MGMT(f, a...) IEEE80211_DEBUG(IEEE80211_DL_MGMT, f, ## a) +#define IEEE80211_DEBUG_FRAG(f, a...) IEEE80211_DEBUG(IEEE80211_DL_FRAG, f, ## a) +#define IEEE80211_DEBUG_EAP(f, a...) IEEE80211_DEBUG(IEEE80211_DL_EAP, f, ## a) +#define IEEE80211_DEBUG_DROP(f, a...) IEEE80211_DEBUG(IEEE80211_DL_DROP, f, ## a) +#define IEEE80211_DEBUG_TX(f, a...) IEEE80211_DEBUG(IEEE80211_DL_TX, f, ## a) +#define IEEE80211_DEBUG_RX(f, a...) IEEE80211_DEBUG(IEEE80211_DL_RX, f, ## a) +#include <linux/netdevice.h> +#include <linux/wireless.h> +#include <linux/if_arp.h> /* ARPHRD_ETHER */ + +#ifndef WIRELESS_SPY +#define WIRELESS_SPY // enable iwspy support +#endif +#include <net/iw_handler.h> // new driver API + +#ifndef ETH_P_PAE +#define ETH_P_PAE 0x888E /* Port Access Entity (IEEE 802.1X) */ +#endif /* ETH_P_PAE */ + +#define ETH_P_PREAUTH 0x88C7 /* IEEE 802.11i pre-authentication */ + +#ifndef ETH_P_80211_RAW +#define ETH_P_80211_RAW (ETH_P_ECONET + 1) +#endif + +/* IEEE 802.11 defines */ + +#define P80211_OUI_LEN 3 + +struct ieee80211_snap_hdr { + + u8 dsap; /* always 0xAA */ + u8 ssap; /* always 0xAA */ + u8 ctrl; /* always 0x03 */ + u8 oui[P80211_OUI_LEN]; /* organizational universal id */ + +} __attribute__ ((packed)); + +#define SNAP_SIZE sizeof(struct ieee80211_snap_hdr) + +#define WLAN_FC_GET_TYPE(fc) ((fc) & IEEE80211_FCTL_FTYPE) +#define WLAN_FC_GET_STYPE(fc) ((fc) & IEEE80211_FCTL_STYPE) + +#define WLAN_GET_SEQ_FRAG(seq) ((seq) & IEEE80211_SCTL_FRAG) +#define WLAN_GET_SEQ_SEQ(seq) ((seq) & IEEE80211_SCTL_SEQ) + +/* Authentication algorithms */ +#define WLAN_AUTH_OPEN 0 +#define WLAN_AUTH_SHARED_KEY 1 + +#define WLAN_AUTH_CHALLENGE_LEN 128 + +#define WLAN_CAPABILITY_BSS (1<<0) +#define WLAN_CAPABILITY_IBSS (1<<1) +#define WLAN_CAPABILITY_CF_POLLABLE (1<<2) +#define WLAN_CAPABILITY_CF_POLL_REQUEST (1<<3) +#define WLAN_CAPABILITY_PRIVACY (1<<4) +#define WLAN_CAPABILITY_SHORT_PREAMBLE (1<<5) +#define WLAN_CAPABILITY_PBCC (1<<6) +#define WLAN_CAPABILITY_CHANNEL_AGILITY (1<<7) + +/* Status codes */ +#define WLAN_STATUS_SUCCESS 0 +#define WLAN_STATUS_UNSPECIFIED_FAILURE 1 +#define WLAN_STATUS_CAPS_UNSUPPORTED 10 +#define WLAN_STATUS_REASSOC_NO_ASSOC 11 +#define WLAN_STATUS_ASSOC_DENIED_UNSPEC 12 +#define WLAN_STATUS_NOT_SUPPORTED_AUTH_ALG 13 +#define WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION 14 +#define WLAN_STATUS_CHALLENGE_FAIL 15 +#define WLAN_STATUS_AUTH_TIMEOUT 16 +#define WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA 17 +#define WLAN_STATUS_ASSOC_DENIED_RATES 18 +/* 802.11b */ +#define WLAN_STATUS_ASSOC_DENIED_NOSHORT 19 +#define WLAN_STATUS_ASSOC_DENIED_NOPBCC 20 +#define WLAN_STATUS_ASSOC_DENIED_NOAGILITY 21 + +/* Reason codes */ +#define WLAN_REASON_UNSPECIFIED 1 +#define WLAN_REASON_PREV_AUTH_NOT_VALID 2 +#define WLAN_REASON_DEAUTH_LEAVING 3 +#define WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY 4 +#define WLAN_REASON_DISASSOC_AP_BUSY 5 +#define WLAN_REASON_CLASS2_FRAME_FROM_NONAUTH_STA 6 +#define WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA 7 +#define WLAN_REASON_DISASSOC_STA_HAS_LEFT 8 +#define WLAN_REASON_STA_REQ_ASSOC_WITHOUT_AUTH 9 + + +/* Information Element IDs */ +#define WLAN_EID_SSID 0 +#define WLAN_EID_SUPP_RATES 1 +#define WLAN_EID_FH_PARAMS 2 +#define WLAN_EID_DS_PARAMS 3 +#define WLAN_EID_CF_PARAMS 4 +#define WLAN_EID_TIM 5 +#define WLAN_EID_IBSS_PARAMS 6 +#define WLAN_EID_CHALLENGE 16 +#define WLAN_EID_RSN 48 +#define WLAN_EID_GENERIC 221 + +#define IEEE80211_MGMT_HDR_LEN 24 +#define IEEE80211_DATA_HDR3_LEN 24 +#define IEEE80211_DATA_HDR4_LEN 30 + + +#define IEEE80211_STATMASK_SIGNAL (1<<0) +#define IEEE80211_STATMASK_RSSI (1<<1) +#define IEEE80211_STATMASK_NOISE (1<<2) +#define IEEE80211_STATMASK_RATE (1<<3) +#define IEEE80211_STATMASK_WEMASK 0x7 + + +#define IEEE80211_CCK_MODULATION (1<<0) +#define IEEE80211_OFDM_MODULATION (1<<1) + +#define IEEE80211_24GHZ_BAND (1<<0) +#define IEEE80211_52GHZ_BAND (1<<1) + +#define IEEE80211_CCK_RATE_1MB 0x02 +#define IEEE80211_CCK_RATE_2MB 0x04 +#define IEEE80211_CCK_RATE_5MB 0x0B +#define IEEE80211_CCK_RATE_11MB 0x16 +#define IEEE80211_OFDM_RATE_6MB 0x0C +#define IEEE80211_OFDM_RATE_9MB 0x12 +#define IEEE80211_OFDM_RATE_12MB 0x18 +#define IEEE80211_OFDM_RATE_18MB 0x24 +#define IEEE80211_OFDM_RATE_24MB 0x30 +#define IEEE80211_OFDM_RATE_36MB 0x48 +#define IEEE80211_OFDM_RATE_48MB 0x60 +#define IEEE80211_OFDM_RATE_54MB 0x6C +#define IEEE80211_BASIC_RATE_MASK 0x80 + +#define IEEE80211_CCK_RATE_1MB_MASK (1<<0) +#define IEEE80211_CCK_RATE_2MB_MASK (1<<1) +#define IEEE80211_CCK_RATE_5MB_MASK (1<<2) +#define IEEE80211_CCK_RATE_11MB_MASK (1<<3) +#define IEEE80211_OFDM_RATE_6MB_MASK (1<<4) +#define IEEE80211_OFDM_RATE_9MB_MASK (1<<5) +#define IEEE80211_OFDM_RATE_12MB_MASK (1<<6) +#define IEEE80211_OFDM_RATE_18MB_MASK (1<<7) +#define IEEE80211_OFDM_RATE_24MB_MASK (1<<8) +#define IEEE80211_OFDM_RATE_36MB_MASK (1<<9) +#define IEEE80211_OFDM_RATE_48MB_MASK (1<<10) +#define IEEE80211_OFDM_RATE_54MB_MASK (1<<11) + +#define IEEE80211_CCK_RATES_MASK 0x0000000F +#define IEEE80211_CCK_BASIC_RATES_MASK (IEEE80211_CCK_RATE_1MB_MASK | \ + IEEE80211_CCK_RATE_2MB_MASK) +#define IEEE80211_CCK_DEFAULT_RATES_MASK (IEEE80211_CCK_BASIC_RATES_MASK | \ + IEEE80211_CCK_RATE_5MB_MASK | \ + IEEE80211_CCK_RATE_11MB_MASK) + +#define IEEE80211_OFDM_RATES_MASK 0x00000FF0 +#define IEEE80211_OFDM_BASIC_RATES_MASK (IEEE80211_OFDM_RATE_6MB_MASK | \ + IEEE80211_OFDM_RATE_12MB_MASK | \ + IEEE80211_OFDM_RATE_24MB_MASK) +#define IEEE80211_OFDM_DEFAULT_RATES_MASK (IEEE80211_OFDM_BASIC_RATES_MASK | \ + IEEE80211_OFDM_RATE_9MB_MASK | \ + IEEE80211_OFDM_RATE_18MB_MASK | \ + IEEE80211_OFDM_RATE_36MB_MASK | \ + IEEE80211_OFDM_RATE_48MB_MASK | \ + IEEE80211_OFDM_RATE_54MB_MASK) +#define IEEE80211_DEFAULT_RATES_MASK (IEEE80211_OFDM_DEFAULT_RATES_MASK | \ + IEEE80211_CCK_DEFAULT_RATES_MASK) + +#define IEEE80211_NUM_OFDM_RATES 8 +#define IEEE80211_NUM_CCK_RATES 4 +#define IEEE80211_OFDM_SHIFT_MASK_A 4 + + + + +/* NOTE: This data is for statistical purposes; not all hardware provides this + * information for frames received. Not setting these will not cause + * any adverse affects. */ +struct ieee80211_rx_stats { + u32 mac_time; + s8 rssi; + u8 signal; + u8 noise; + u16 rate; /* in 100 kbps */ + u8 received_channel; + u8 control; + u8 mask; + u8 freq; + u16 len; +}; + +/* IEEE 802.11 requires that STA supports concurrent reception of at least + * three fragmented frames. This define can be increased to support more + * concurrent frames, but it should be noted that each entry can consume about + * 2 kB of RAM and increasing cache size will slow down frame reassembly. */ +#define IEEE80211_FRAG_CACHE_LEN 4 + +struct ieee80211_frag_entry { + unsigned long first_frag_time; + unsigned int seq; + unsigned int last_frag; + struct sk_buff *skb; + u8 src_addr[ETH_ALEN]; + u8 dst_addr[ETH_ALEN]; +}; + +struct ieee80211_stats { + unsigned int tx_unicast_frames; + unsigned int tx_multicast_frames; + unsigned int tx_fragments; + unsigned int tx_unicast_octets; + unsigned int tx_multicast_octets; + unsigned int tx_deferred_transmissions; + unsigned int tx_single_retry_frames; + unsigned int tx_multiple_retry_frames; + unsigned int tx_retry_limit_exceeded; + unsigned int tx_discards; + unsigned int rx_unicast_frames; + unsigned int rx_multicast_frames; + unsigned int rx_fragments; + unsigned int rx_unicast_octets; + unsigned int rx_multicast_octets; + unsigned int rx_fcs_errors; + unsigned int rx_discards_no_buffer; + unsigned int tx_discards_wrong_sa; + unsigned int rx_discards_undecryptable; + unsigned int rx_message_in_msg_fragments; + unsigned int rx_message_in_bad_msg_fragments; +}; + +struct ieee80211_device; + +#include "ieee80211_crypt.h" + +#define SEC_KEY_1 (1<<0) +#define SEC_KEY_2 (1<<1) +#define SEC_KEY_3 (1<<2) +#define SEC_KEY_4 (1<<3) +#define SEC_ACTIVE_KEY (1<<4) +#define SEC_AUTH_MODE (1<<5) +#define SEC_UNICAST_GROUP (1<<6) +#define SEC_LEVEL (1<<7) +#define SEC_ENABLED (1<<8) + +#define SEC_LEVEL_0 0 /* None */ +#define SEC_LEVEL_1 1 /* WEP 40 and 104 bit */ +#define SEC_LEVEL_2 2 /* Level 1 + TKIP */ +#define SEC_LEVEL_2_CKIP 3 /* Level 1 + CKIP */ +#define SEC_LEVEL_3 4 /* Level 2 + CCMP */ + +#define WEP_KEYS 4 +#define WEP_KEY_LEN 13 + +struct ieee80211_security { + u16 active_key:2, + enabled:1, + auth_mode:2, + auth_algo:4, + unicast_uses_group:1; + u8 key_sizes[WEP_KEYS]; + u8 keys[WEP_KEYS][WEP_KEY_LEN]; + u8 level; + u16 flags; +} __attribute__ ((packed)); + + +/* + + 802.11 data frame from AP + + ,-------------------------------------------------------------------. +Bytes | 2 | 2 | 6 | 6 | 6 | 2 | 0..2312 | 4 | + |------|------|---------|---------|---------|------|---------|------| +Desc. | ctrl | dura | DA/RA | TA | SA | Sequ | frame | fcs | + | | tion | (BSSID) | | | ence | data | | + `-------------------------------------------------------------------' + +Total: 28-2340 bytes + +*/ + +struct ieee80211_header_data { + u16 frame_ctl; + u16 duration_id; + u8 addr1[6]; + u8 addr2[6]; + u8 addr3[6]; + u16 seq_ctrl; +}; + +#define BEACON_PROBE_SSID_ID_POSITION 12 + +/* Management Frame Information Element Types */ +#define MFIE_TYPE_SSID 0 +#define MFIE_TYPE_RATES 1 +#define MFIE_TYPE_FH_SET 2 +#define MFIE_TYPE_DS_SET 3 +#define MFIE_TYPE_CF_SET 4 +#define MFIE_TYPE_TIM 5 +#define MFIE_TYPE_IBSS_SET 6 +#define MFIE_TYPE_CHALLENGE 16 +#define MFIE_TYPE_RSN 48 +#define MFIE_TYPE_RATES_EX 50 +#define MFIE_TYPE_GENERIC 221 + +struct ieee80211_info_element_hdr { + u8 id; + u8 len; +} __attribute__ ((packed)); + +struct ieee80211_info_element { + u8 id; + u8 len; + u8 data[0]; +} __attribute__ ((packed)); + +/* + * These are the data types that can make up management packets + * + u16 auth_algorithm; + u16 auth_sequence; + u16 beacon_interval; + u16 capability; + u8 current_ap[ETH_ALEN]; + u16 listen_interval; + struct { + u16 association_id:14, reserved:2; + } __attribute__ ((packed)); + u32 time_stamp[2]; + u16 reason; + u16 status; +*/ + +struct ieee80211_authentication { + struct ieee80211_header_data header; + u16 algorithm; + u16 transaction; + u16 status; + struct ieee80211_info_element info_element; +} __attribute__ ((packed)); + + +struct ieee80211_probe_response { + struct ieee80211_header_data header; + u32 time_stamp[2]; + u16 beacon_interval; + u16 capability; + struct ieee80211_info_element info_element; +} __attribute__ ((packed)); + +struct ieee80211_assoc_request_frame { + u16 capability; + u16 listen_interval; + u8 current_ap[ETH_ALEN]; + struct ieee80211_info_element info_element; +} __attribute__ ((packed)); + +struct ieee80211_assoc_response_frame { + struct ieee80211_hdr_3addr header; + u16 capability; + u16 status; + u16 aid; + struct ieee80211_info_element info_element; /* supported rates */ +} __attribute__ ((packed)); + + +struct ieee80211_txb { + u8 nr_frags; + u8 encrypted; + u16 reserved; + u16 frag_size; + u16 payload_size; + struct sk_buff *fragments[0]; +}; + + +/* SWEEP TABLE ENTRIES NUMBER*/ +#define MAX_SWEEP_TAB_ENTRIES 42 +#define MAX_SWEEP_TAB_ENTRIES_PER_PACKET 7 +/* MAX_RATES_LENGTH needs to be 12. The spec says 8, and many APs + * only use 8, and then use extended rates for the remaining supported + * rates. Other APs, however, stick all of their supported rates on the + * main rates information element... */ +#define MAX_RATES_LENGTH ((u8)12) +#define MAX_RATES_EX_LENGTH ((u8)16) +#define MAX_NETWORK_COUNT 128 + +#define CRC_LENGTH 4U + +#define MAX_WPA_IE_LEN 64 + +#define NETWORK_EMPTY_ESSID (1<<0) +#define NETWORK_HAS_OFDM (1<<1) +#define NETWORK_HAS_CCK (1<<2) + +struct ieee80211_network { + /* These entries are used to identify a unique network */ + u8 bssid[ETH_ALEN]; + u8 channel; + /* Ensure null-terminated for any debug msgs */ + u8 ssid[IW_ESSID_MAX_SIZE + 1]; + u8 ssid_len; + + /* These are network statistics */ + struct ieee80211_rx_stats stats; + u16 capability; + u8 rates[MAX_RATES_LENGTH]; + u8 rates_len; + u8 rates_ex[MAX_RATES_EX_LENGTH]; + u8 rates_ex_len; + unsigned long last_scanned; + u8 mode; + u8 flags; + u32 last_associate; + u32 time_stamp[2]; + u16 beacon_interval; + u16 listen_interval; + u16 atim_window; + u8 wpa_ie[MAX_WPA_IE_LEN]; + size_t wpa_ie_len; + u8 rsn_ie[MAX_WPA_IE_LEN]; + size_t rsn_ie_len; + struct list_head list; +}; + +enum ieee80211_state { + IEEE80211_UNINITIALIZED = 0, + IEEE80211_INITIALIZED, + IEEE80211_ASSOCIATING, + IEEE80211_ASSOCIATED, + IEEE80211_AUTHENTICATING, + IEEE80211_AUTHENTICATED, + IEEE80211_SHUTDOWN +}; + +#define DEFAULT_MAX_SCAN_AGE (15 * HZ) +#define DEFAULT_FTS 2346 +#define MAC_FMT "%02x:%02x:%02x:%02x:%02x:%02x" +#define MAC_ARG(x) ((u8*)(x))[0],((u8*)(x))[1],((u8*)(x))[2],((u8*)(x))[3],((u8*)(x))[4],((u8*)(x))[5] + + +extern inline int is_multicast_ether_addr(const u8 *addr) +{ + return ((addr[0] != 0xff) && (0x01 & addr[0])); +} + +extern inline int is_broadcast_ether_addr(const u8 *addr) +{ + return ((addr[0] == 0xff) && (addr[1] == 0xff) && (addr[2] == 0xff) && \ + (addr[3] == 0xff) && (addr[4] == 0xff) && (addr[5] == 0xff)); +} + +#define CFG_IEEE80211_RESERVE_FCS (1<<0) +#define CFG_IEEE80211_COMPUTE_FCS (1<<1) + +struct ieee80211_device { + struct net_device *dev; + + /* Bookkeeping structures */ + struct net_device_stats stats; + struct ieee80211_stats ieee_stats; + + /* Probe / Beacon management */ + struct list_head network_free_list; + struct list_head network_list; + struct ieee80211_network *networks; + int scans; + int scan_age; + + int iw_mode; /* operating mode (IW_MODE_*) */ + + spinlock_t lock; + + int tx_headroom; /* Set to size of any additional room needed at front + * of allocated Tx SKBs */ + u32 config; + + /* WEP and other encryption related settings at the device level */ + int open_wep; /* Set to 1 to allow unencrypted frames */ + + int reset_on_keychange; /* Set to 1 if the HW needs to be reset on + * WEP key changes */ + + /* If the host performs {en,de}cryption, then set to 1 */ + int host_encrypt; + int host_decrypt; + int ieee802_1x; /* is IEEE 802.1X used */ + + /* WPA data */ + int wpa_enabled; + int drop_unencrypted; + int tkip_countermeasures; + int privacy_invoked; + size_t wpa_ie_len; + u8 *wpa_ie; + + struct list_head crypt_deinit_list; + struct ieee80211_crypt_data *crypt[WEP_KEYS]; + int tx_keyidx; /* default TX key index (crypt[tx_keyidx]) */ + struct timer_list crypt_deinit_timer; + + int bcrx_sta_key; /* use individual keys to override default keys even + * with RX of broad/multicast frames */ + + /* Fragmentation structures */ + struct ieee80211_frag_entry frag_cache[IEEE80211_FRAG_CACHE_LEN]; + unsigned int frag_next_idx; + u16 fts; /* Fragmentation Threshold */ + + /* Association info */ + u8 bssid[ETH_ALEN]; + + enum ieee80211_state state; + + int mode; /* A, B, G */ + int modulation; /* CCK, OFDM */ + int freq_band; /* 2.4Ghz, 5.2Ghz, Mixed */ + int abg_ture; /* ABG flag */ + + /* Callback functions */ + void (*set_security)(struct net_device *dev, + struct ieee80211_security *sec); + int (*hard_start_xmit)(struct ieee80211_txb *txb, + struct net_device *dev); + int (*reset_port)(struct net_device *dev); + + /* This must be the last item so that it points to the data + * allocated beyond this structure by alloc_ieee80211 */ + u8 priv[0]; +}; + +#define IEEE_A (1<<0) +#define IEEE_B (1<<1) +#define IEEE_G (1<<2) +#define IEEE_MODE_MASK (IEEE_A|IEEE_B|IEEE_G) + +extern inline void *ieee80211_priv(struct net_device *dev) +{ + return ((struct ieee80211_device *)netdev_priv(dev))->priv; +} + +extern inline int ieee80211_is_empty_essid(const char *essid, int essid_len) +{ + /* Single white space is for Linksys APs */ + if (essid_len == 1 && essid[0] == ' ') + return 1; + + /* Otherwise, if the entire essid is 0, we assume it is hidden */ + while (essid_len) { + essid_len--; + if (essid[essid_len] != '\0') + return 0; + } + + return 1; +} + +extern inline int ieee80211_is_valid_mode(struct ieee80211_device *ieee, int mode) +{ + /* + * It is possible for both access points and our device to support + * combinations of modes, so as long as there is one valid combination + * of ap/device supported modes, then return success + * + */ + if ((mode & IEEE_A) && + (ieee->modulation & IEEE80211_OFDM_MODULATION) && + (ieee->freq_band & IEEE80211_52GHZ_BAND)) + return 1; + + if ((mode & IEEE_G) && + (ieee->modulation & IEEE80211_OFDM_MODULATION) && + (ieee->freq_band & IEEE80211_24GHZ_BAND)) + return 1; + + if ((mode & IEEE_B) && + (ieee->modulation & IEEE80211_CCK_MODULATION) && + (ieee->freq_band & IEEE80211_24GHZ_BAND)) + return 1; + + return 0; +} + +extern inline int ieee80211_get_hdrlen(u16 fc) +{ + int hdrlen = 24; + + switch (WLAN_FC_GET_TYPE(fc)) { + case IEEE80211_FTYPE_DATA: + if ((fc & IEEE80211_FCTL_FROMDS) && (fc & IEEE80211_FCTL_TODS)) + hdrlen = 30; /* Addr4 */ + break; + case IEEE80211_FTYPE_CTL: + switch (WLAN_FC_GET_STYPE(fc)) { + case IEEE80211_STYPE_CTS: + case IEEE80211_STYPE_ACK: + hdrlen = 10; + break; + default: + hdrlen = 16; + break; + } + break; + } + + return hdrlen; +} + + + +/* ieee80211.c */ +extern void free_ieee80211(struct net_device *dev); +extern struct net_device *alloc_ieee80211(int sizeof_priv); + +extern int ieee80211_set_encryption(struct ieee80211_device *ieee); + +/* ieee80211_tx.c */ + + +extern int ieee80211_xmit(struct sk_buff *skb, + struct net_device *dev); +extern void ieee80211_txb_free(struct ieee80211_txb *); + + +/* ieee80211_rx.c */ +extern int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, + struct ieee80211_rx_stats *rx_stats); +extern void ieee80211_rx_mgt(struct ieee80211_device *ieee, + struct ieee80211_hdr *header, + struct ieee80211_rx_stats *stats); + +/* iee80211_wx.c */ +extern int ieee80211_wx_get_scan(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key); +extern int ieee80211_wx_set_encode(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key); +extern int ieee80211_wx_get_encode(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key); + + +extern inline void ieee80211_increment_scans(struct ieee80211_device *ieee) +{ + ieee->scans++; +} + +extern inline int ieee80211_get_scans(struct ieee80211_device *ieee) +{ + return ieee->scans; +} + +static inline const char *escape_essid(const char *essid, u8 essid_len) { + static char escaped[IW_ESSID_MAX_SIZE * 2 + 1]; + const char *s = essid; + char *d = escaped; + + if (ieee80211_is_empty_essid(essid, essid_len)) { + memcpy(escaped, "<hidden>", sizeof("<hidden>")); + return escaped; + } + + essid_len = min(essid_len, (u8)IW_ESSID_MAX_SIZE); + while (essid_len--) { + if (*s == '\0') { + *d++ = '\\'; + *d++ = '0'; + s++; + } else { + *d++ = *s++; + } + } + *d = '\0'; + return escaped; +} +#endif /* IEEE80211_H */ diff --git a/include/net/ieee80211_crypt.h b/include/net/ieee80211_crypt.h new file mode 100644 index 000000000000..b58a3bcc0dc0 --- /dev/null +++ b/include/net/ieee80211_crypt.h @@ -0,0 +1,86 @@ +/* + * Original code based on Host AP (software wireless LAN access point) driver + * for Intersil Prism2/2.5/3. + * + * Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + * <jkmaline@cc.hut.fi> + * Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + * + * Adaption to a generic IEEE 802.11 stack by James Ketrenos + * <jketreno@linux.intel.com> + * + * Copyright (c) 2004, Intel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ + +/* + * This file defines the interface to the ieee80211 crypto module. + */ +#ifndef IEEE80211_CRYPT_H +#define IEEE80211_CRYPT_H + +#include <linux/skbuff.h> + +struct ieee80211_crypto_ops { + const char *name; + + /* init new crypto context (e.g., allocate private data space, + * select IV, etc.); returns NULL on failure or pointer to allocated + * private data on success */ + void * (*init)(int keyidx); + + /* deinitialize crypto context and free allocated private data */ + void (*deinit)(void *priv); + + /* encrypt/decrypt return < 0 on error or >= 0 on success. The return + * value from decrypt_mpdu is passed as the keyidx value for + * decrypt_msdu. skb must have enough head and tail room for the + * encryption; if not, error will be returned; these functions are + * called for all MPDUs (i.e., fragments). + */ + int (*encrypt_mpdu)(struct sk_buff *skb, int hdr_len, void *priv); + int (*decrypt_mpdu)(struct sk_buff *skb, int hdr_len, void *priv); + + /* These functions are called for full MSDUs, i.e. full frames. + * These can be NULL if full MSDU operations are not needed. */ + int (*encrypt_msdu)(struct sk_buff *skb, int hdr_len, void *priv); + int (*decrypt_msdu)(struct sk_buff *skb, int keyidx, int hdr_len, + void *priv); + + int (*set_key)(void *key, int len, u8 *seq, void *priv); + int (*get_key)(void *key, int len, u8 *seq, void *priv); + + /* procfs handler for printing out key information and possible + * statistics */ + char * (*print_stats)(char *p, void *priv); + + /* maximum number of bytes added by encryption; encrypt buf is + * allocated with extra_prefix_len bytes, copy of in_buf, and + * extra_postfix_len; encrypt need not use all this space, but + * the result must start at the beginning of the buffer and correct + * length must be returned */ + int extra_prefix_len, extra_postfix_len; + + struct module *owner; +}; + +struct ieee80211_crypt_data { + struct list_head list; /* delayed deletion list */ + struct ieee80211_crypto_ops *ops; + void *priv; + atomic_t refcnt; +}; + +int ieee80211_register_crypto_ops(struct ieee80211_crypto_ops *ops); +int ieee80211_unregister_crypto_ops(struct ieee80211_crypto_ops *ops); +struct ieee80211_crypto_ops * ieee80211_get_crypto_ops(const char *name); +void ieee80211_crypt_deinit_entries(struct ieee80211_device *, int); +void ieee80211_crypt_deinit_handler(unsigned long); +void ieee80211_crypt_delayed_deinit(struct ieee80211_device *ieee, + struct ieee80211_crypt_data **crypt); + +#endif diff --git a/net/Kconfig b/net/Kconfig index 9251b28e8d5d..8a12ea8f0c05 100644 --- a/net/Kconfig +++ b/net/Kconfig @@ -640,6 +640,8 @@ source "net/irda/Kconfig" source "net/bluetooth/Kconfig" +source "net/ieee80211/Kconfig" + source "drivers/net/Kconfig" endmenu diff --git a/net/Makefile b/net/Makefile index 8e2bdc025ab8..83bc52d87bae 100644 --- a/net/Makefile +++ b/net/Makefile @@ -42,6 +42,7 @@ obj-$(CONFIG_DECNET) += decnet/ obj-$(CONFIG_ECONET) += econet/ obj-$(CONFIG_VLAN_8021Q) += 8021q/ obj-$(CONFIG_IP_SCTP) += sctp/ +obj-$(CONFIG_IEEE80211) += ieee80211/ ifeq ($(CONFIG_NET),y) obj-$(CONFIG_SYSCTL) += sysctl_net.o diff --git a/net/core/wireless.c b/net/core/wireless.c index 750cc5daeb03..b2fe378dfbf8 100644 --- a/net/core/wireless.c +++ b/net/core/wireless.c @@ -2,7 +2,7 @@ * This file implement the Wireless Extensions APIs. * * Authors : Jean Tourrilhes - HPL - <jt@hpl.hp.com> - * Copyright (c) 1997-2004 Jean Tourrilhes, All Rights Reserved. + * Copyright (c) 1997-2005 Jean Tourrilhes, All Rights Reserved. * * (As all part of the Linux kernel, this file is GPL) */ @@ -187,6 +187,12 @@ static const struct iw_ioctl_description standard_ioctl[] = { .header_type = IW_HEADER_TYPE_ADDR, .flags = IW_DESCR_FLAG_DUMP, }, + [SIOCSIWMLME - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .min_tokens = sizeof(struct iw_mlme), + .max_tokens = sizeof(struct iw_mlme), + }, [SIOCGIWAPLIST - SIOCIWFIRST] = { .header_type = IW_HEADER_TYPE_POINT, .token_size = sizeof(struct sockaddr) + @@ -195,7 +201,10 @@ static const struct iw_ioctl_description standard_ioctl[] = { .flags = IW_DESCR_FLAG_NOMAX, }, [SIOCSIWSCAN - SIOCIWFIRST] = { - .header_type = IW_HEADER_TYPE_PARAM, + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .min_tokens = 0, + .max_tokens = sizeof(struct iw_scan_req), }, [SIOCGIWSCAN - SIOCIWFIRST] = { .header_type = IW_HEADER_TYPE_POINT, @@ -273,6 +282,42 @@ static const struct iw_ioctl_description standard_ioctl[] = { [SIOCGIWPOWER - SIOCIWFIRST] = { .header_type = IW_HEADER_TYPE_PARAM, }, + [SIOCSIWGENIE - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = IW_GENERIC_IE_MAX, + }, + [SIOCGIWGENIE - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = IW_GENERIC_IE_MAX, + }, + [SIOCSIWAUTH - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_PARAM, + }, + [SIOCGIWAUTH - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_PARAM, + }, + [SIOCSIWENCODEEXT - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .min_tokens = sizeof(struct iw_encode_ext), + .max_tokens = sizeof(struct iw_encode_ext) + + IW_ENCODING_TOKEN_MAX, + }, + [SIOCGIWENCODEEXT - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .min_tokens = sizeof(struct iw_encode_ext), + .max_tokens = sizeof(struct iw_encode_ext) + + IW_ENCODING_TOKEN_MAX, + }, + [SIOCSIWPMKSA - SIOCIWFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .min_tokens = sizeof(struct iw_pmksa), + .max_tokens = sizeof(struct iw_pmksa), + }, }; static const int standard_ioctl_num = (sizeof(standard_ioctl) / sizeof(struct iw_ioctl_description)); @@ -299,6 +344,31 @@ static const struct iw_ioctl_description standard_event[] = { [IWEVEXPIRED - IWEVFIRST] = { .header_type = IW_HEADER_TYPE_ADDR, }, + [IWEVGENIE - IWEVFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = IW_GENERIC_IE_MAX, + }, + [IWEVMICHAELMICFAILURE - IWEVFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = sizeof(struct iw_michaelmicfailure), + }, + [IWEVASSOCREQIE - IWEVFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = IW_GENERIC_IE_MAX, + }, + [IWEVASSOCRESPIE - IWEVFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = IW_GENERIC_IE_MAX, + }, + [IWEVPMKIDCAND - IWEVFIRST] = { + .header_type = IW_HEADER_TYPE_POINT, + .token_size = 1, + .max_tokens = sizeof(struct iw_pmkid_cand), + }, }; static const int standard_event_num = (sizeof(standard_event) / sizeof(struct iw_ioctl_description)); diff --git a/net/ieee80211/Kconfig b/net/ieee80211/Kconfig new file mode 100644 index 000000000000..23b23f72a9a4 --- /dev/null +++ b/net/ieee80211/Kconfig @@ -0,0 +1,67 @@ +config IEEE80211 + tristate "Generic IEEE 802.11 Networking Stack" + select NET_RADIO + ---help--- + This option enables the hardware independent IEEE 802.11 + networking stack. + +config IEEE80211_DEBUG + bool "Enable full debugging output" + depends on IEEE80211 + ---help--- + This option will enable debug tracing output for the + ieee80211 network stack. + + This will result in the kernel module being ~70k larger. You + can control which debug output is sent to the kernel log by + setting the value in + + /proc/net/ieee80211/debug_level + + For example: + + % echo 0x00000FFO > /proc/net/ieee80211/debug_level + + For a list of values you can assign to debug_level, you + can look at the bit mask values in <net/ieee80211.h> + + If you are not trying to debug or develop the ieee80211 + subsystem, you most likely want to say N here. + +config IEEE80211_CRYPT_WEP + tristate "IEEE 802.11 WEP encryption (802.1x)" + depends on IEEE80211 + select CRYPTO + select CRYPTO_ARC4 + select CRC32 + ---help--- + Include software based cipher suites in support of IEEE + 802.11's WEP. This is needed for WEP as well as 802.1x. + + This can be compiled as a modules and it will be called + "ieee80211_crypt_wep". + +config IEEE80211_CRYPT_CCMP + tristate "IEEE 802.11i CCMP support" + depends on IEEE80211 + select CRYPTO_AES + ---help--- + Include software based cipher suites in support of IEEE 802.11i + (aka TGi, WPA, WPA2, WPA-PSK, etc.) for use with CCMP enabled + networks. + + This can be compiled as a modules and it will be called + "ieee80211_crypt_ccmp". + +config IEEE80211_CRYPT_TKIP + tristate "IEEE 802.11i TKIP encryption" + depends on IEEE80211 + select CRYPTO_MICHAEL_MIC + ---help--- + Include software based cipher suites in support of IEEE 802.11i + (aka TGi, WPA, WPA2, WPA-PSK, etc.) for use with TKIP enabled + networks. + + This can be compiled as a modules and it will be called + "ieee80211_crypt_tkip". + diff --git a/net/ieee80211/Makefile b/net/ieee80211/Makefile new file mode 100644 index 000000000000..29be9cae1def --- /dev/null +++ b/net/ieee80211/Makefile @@ -0,0 +1,11 @@ +obj-$(CONFIG_IEEE80211) += ieee80211.o +obj-$(CONFIG_IEEE80211) += ieee80211_crypt.o +obj-$(CONFIG_IEEE80211_CRYPT_WEP) += ieee80211_crypt_wep.o +obj-$(CONFIG_IEEE80211_CRYPT_CCMP) += ieee80211_crypt_ccmp.o +obj-$(CONFIG_IEEE80211_CRYPT_TKIP) += ieee80211_crypt_tkip.o +ieee80211-objs := \ + ieee80211_module.o \ + ieee80211_tx.o \ + ieee80211_rx.o \ + ieee80211_wx.o + diff --git a/net/ieee80211/ieee80211_crypt.c b/net/ieee80211/ieee80211_crypt.c new file mode 100644 index 000000000000..05a6f2f298db --- /dev/null +++ b/net/ieee80211/ieee80211_crypt.c @@ -0,0 +1,259 @@ +/* + * Host AP crypto routines + * + * Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + * Portions Copyright (C) 2004, Intel Corporation <jketreno@linux.intel.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + * + */ + +#include <linux/config.h> +#include <linux/version.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <asm/string.h> +#include <asm/errno.h> + +#include <net/ieee80211.h> + +MODULE_AUTHOR("Jouni Malinen"); +MODULE_DESCRIPTION("HostAP crypto"); +MODULE_LICENSE("GPL"); + +struct ieee80211_crypto_alg { + struct list_head list; + struct ieee80211_crypto_ops *ops; +}; + + +struct ieee80211_crypto { + struct list_head algs; + spinlock_t lock; +}; + +static struct ieee80211_crypto *hcrypt; + +void ieee80211_crypt_deinit_entries(struct ieee80211_device *ieee, + int force) +{ + struct list_head *ptr, *n; + struct ieee80211_crypt_data *entry; + + for (ptr = ieee->crypt_deinit_list.next, n = ptr->next; + ptr != &ieee->crypt_deinit_list; ptr = n, n = ptr->next) { + entry = list_entry(ptr, struct ieee80211_crypt_data, list); + + if (atomic_read(&entry->refcnt) != 0 && !force) + continue; + + list_del(ptr); + + if (entry->ops) { + entry->ops->deinit(entry->priv); + module_put(entry->ops->owner); + } + kfree(entry); + } +} + +void ieee80211_crypt_deinit_handler(unsigned long data) +{ + struct ieee80211_device *ieee = (struct ieee80211_device *)data; + unsigned long flags; + + spin_lock_irqsave(&ieee->lock, flags); + ieee80211_crypt_deinit_entries(ieee, 0); + if (!list_empty(&ieee->crypt_deinit_list)) { + printk(KERN_DEBUG "%s: entries remaining in delayed crypt " + "deletion list\n", ieee->dev->name); + ieee->crypt_deinit_timer.expires = jiffies + HZ; + add_timer(&ieee->crypt_deinit_timer); + } + spin_unlock_irqrestore(&ieee->lock, flags); + +} + +void ieee80211_crypt_delayed_deinit(struct ieee80211_device *ieee, + struct ieee80211_crypt_data **crypt) +{ + struct ieee80211_crypt_data *tmp; + unsigned long flags; + + if (*crypt == NULL) + return; + + tmp = *crypt; + *crypt = NULL; + + /* must not run ops->deinit() while there may be pending encrypt or + * decrypt operations. Use a list of delayed deinits to avoid needing + * locking. */ + + spin_lock_irqsave(&ieee->lock, flags); + list_add(&tmp->list, &ieee->crypt_deinit_list); + if (!timer_pending(&ieee->crypt_deinit_timer)) { + ieee->crypt_deinit_timer.expires = jiffies + HZ; + add_timer(&ieee->crypt_deinit_timer); + } + spin_unlock_irqrestore(&ieee->lock, flags); +} + +int ieee80211_register_crypto_ops(struct ieee80211_crypto_ops *ops) +{ + unsigned long flags; + struct ieee80211_crypto_alg *alg; + + if (hcrypt == NULL) + return -1; + + alg = kmalloc(sizeof(*alg), GFP_KERNEL); + if (alg == NULL) + return -ENOMEM; + + memset(alg, 0, sizeof(*alg)); + alg->ops = ops; + + spin_lock_irqsave(&hcrypt->lock, flags); + list_add(&alg->list, &hcrypt->algs); + spin_unlock_irqrestore(&hcrypt->lock, flags); + + printk(KERN_DEBUG "ieee80211_crypt: registered algorithm '%s'\n", + ops->name); + + return 0; +} + +int ieee80211_unregister_crypto_ops(struct ieee80211_crypto_ops *ops) +{ + unsigned long flags; + struct list_head *ptr; + struct ieee80211_crypto_alg *del_alg = NULL; + + if (hcrypt == NULL) + return -1; + + spin_lock_irqsave(&hcrypt->lock, flags); + for (ptr = hcrypt->algs.next; ptr != &hcrypt->algs; ptr = ptr->next) { + struct ieee80211_crypto_alg *alg = + (struct ieee80211_crypto_alg *) ptr; + if (alg->ops == ops) { + list_del(&alg->list); + del_alg = alg; + break; + } + } + spin_unlock_irqrestore(&hcrypt->lock, flags); + + if (del_alg) { + printk(KERN_DEBUG "ieee80211_crypt: unregistered algorithm " + "'%s'\n", ops->name); + kfree(del_alg); + } + + return del_alg ? 0 : -1; +} + + +struct ieee80211_crypto_ops * ieee80211_get_crypto_ops(const char *name) +{ + unsigned long flags; + struct list_head *ptr; + struct ieee80211_crypto_alg *found_alg = NULL; + + if (hcrypt == NULL) + return NULL; + + spin_lock_irqsave(&hcrypt->lock, flags); + for (ptr = hcrypt->algs.next; ptr != &hcrypt->algs; ptr = ptr->next) { + struct ieee80211_crypto_alg *alg = + (struct ieee80211_crypto_alg *) ptr; + if (strcmp(alg->ops->name, name) == 0) { + found_alg = alg; + break; + } + } + spin_unlock_irqrestore(&hcrypt->lock, flags); + + if (found_alg) + return found_alg->ops; + else + return NULL; +} + + +static void * ieee80211_crypt_null_init(int keyidx) { return (void *) 1; } +static void ieee80211_crypt_null_deinit(void *priv) {} + +static struct ieee80211_crypto_ops ieee80211_crypt_null = { + .name = "NULL", + .init = ieee80211_crypt_null_init, + .deinit = ieee80211_crypt_null_deinit, + .encrypt_mpdu = NULL, + .decrypt_mpdu = NULL, + .encrypt_msdu = NULL, + .decrypt_msdu = NULL, + .set_key = NULL, + .get_key = NULL, + .extra_prefix_len = 0, + .extra_postfix_len = 0, + .owner = THIS_MODULE, +}; + + +static int __init ieee80211_crypto_init(void) +{ + int ret = -ENOMEM; + + hcrypt = kmalloc(sizeof(*hcrypt), GFP_KERNEL); + if (!hcrypt) + goto out; + + memset(hcrypt, 0, sizeof(*hcrypt)); + INIT_LIST_HEAD(&hcrypt->algs); + spin_lock_init(&hcrypt->lock); + + ret = ieee80211_register_crypto_ops(&ieee80211_crypt_null); + if (ret < 0) { + kfree(hcrypt); + hcrypt = NULL; + } +out: + return ret; +} + + +static void __exit ieee80211_crypto_deinit(void) +{ + struct list_head *ptr, *n; + + if (hcrypt == NULL) + return; + + for (ptr = hcrypt->algs.next, n = ptr->next; ptr != &hcrypt->algs; + ptr = n, n = ptr->next) { + struct ieee80211_crypto_alg *alg = + (struct ieee80211_crypto_alg *) ptr; + list_del(ptr); + printk(KERN_DEBUG "ieee80211_crypt: unregistered algorithm " + "'%s' (deinit)\n", alg->ops->name); + kfree(alg); + } + + kfree(hcrypt); +} + +EXPORT_SYMBOL(ieee80211_crypt_deinit_entries); +EXPORT_SYMBOL(ieee80211_crypt_deinit_handler); +EXPORT_SYMBOL(ieee80211_crypt_delayed_deinit); + +EXPORT_SYMBOL(ieee80211_register_crypto_ops); +EXPORT_SYMBOL(ieee80211_unregister_crypto_ops); +EXPORT_SYMBOL(ieee80211_get_crypto_ops); + +module_init(ieee80211_crypto_init); +module_exit(ieee80211_crypto_deinit); diff --git a/net/ieee80211/ieee80211_crypt_ccmp.c b/net/ieee80211/ieee80211_crypt_ccmp.c new file mode 100644 index 000000000000..f5f412ae7f28 --- /dev/null +++ b/net/ieee80211/ieee80211_crypt_ccmp.c @@ -0,0 +1,470 @@ +/* + * Host AP crypt: host-based CCMP encryption implementation for Host AP driver + * + * Copyright (c) 2003-2004, Jouni Malinen <jkmaline@cc.hut.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ + +#include <linux/config.h> +#include <linux/version.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/random.h> +#include <linux/skbuff.h> +#include <linux/netdevice.h> +#include <linux/if_ether.h> +#include <linux/if_arp.h> +#include <asm/string.h> +#include <linux/wireless.h> + +#include <net/ieee80211.h> + + +#include <linux/crypto.h> +#include <asm/scatterlist.h> + +MODULE_AUTHOR("Jouni Malinen"); +MODULE_DESCRIPTION("Host AP crypt: CCMP"); +MODULE_LICENSE("GPL"); + +#define AES_BLOCK_LEN 16 +#define CCMP_HDR_LEN 8 +#define CCMP_MIC_LEN 8 +#define CCMP_TK_LEN 16 +#define CCMP_PN_LEN 6 + +struct ieee80211_ccmp_data { + u8 key[CCMP_TK_LEN]; + int key_set; + + u8 tx_pn[CCMP_PN_LEN]; + u8 rx_pn[CCMP_PN_LEN]; + + u32 dot11RSNAStatsCCMPFormatErrors; + u32 dot11RSNAStatsCCMPReplays; + u32 dot11RSNAStatsCCMPDecryptErrors; + + int key_idx; + + struct crypto_tfm *tfm; + + /* scratch buffers for virt_to_page() (crypto API) */ + u8 tx_b0[AES_BLOCK_LEN], tx_b[AES_BLOCK_LEN], + tx_e[AES_BLOCK_LEN], tx_s0[AES_BLOCK_LEN]; + u8 rx_b0[AES_BLOCK_LEN], rx_b[AES_BLOCK_LEN], rx_a[AES_BLOCK_LEN]; +}; + +void ieee80211_ccmp_aes_encrypt(struct crypto_tfm *tfm, + const u8 pt[16], u8 ct[16]) +{ + struct scatterlist src, dst; + + src.page = virt_to_page(pt); + src.offset = offset_in_page(pt); + src.length = AES_BLOCK_LEN; + + dst.page = virt_to_page(ct); + dst.offset = offset_in_page(ct); + dst.length = AES_BLOCK_LEN; + + crypto_cipher_encrypt(tfm, &dst, &src, AES_BLOCK_LEN); +} + +static void * ieee80211_ccmp_init(int key_idx) +{ + struct ieee80211_ccmp_data *priv; + + priv = kmalloc(sizeof(*priv), GFP_ATOMIC); + if (priv == NULL) + goto fail; + memset(priv, 0, sizeof(*priv)); + priv->key_idx = key_idx; + + priv->tfm = crypto_alloc_tfm("aes", 0); + if (priv->tfm == NULL) { + printk(KERN_DEBUG "ieee80211_crypt_ccmp: could not allocate " + "crypto API aes\n"); + goto fail; + } + + return priv; + +fail: + if (priv) { + if (priv->tfm) + crypto_free_tfm(priv->tfm); + kfree(priv); + } + + return NULL; +} + + +static void ieee80211_ccmp_deinit(void *priv) +{ + struct ieee80211_ccmp_data *_priv = priv; + if (_priv && _priv->tfm) + crypto_free_tfm(_priv->tfm); + kfree(priv); +} + + +static inline void xor_block(u8 *b, u8 *a, size_t len) +{ + int i; + for (i = 0; i < len; i++) + b[i] ^= a[i]; +} + + +static void ccmp_init_blocks(struct crypto_tfm *tfm, + struct ieee80211_hdr *hdr, + u8 *pn, size_t dlen, u8 *b0, u8 *auth, + u8 *s0) +{ + u8 *pos, qc = 0; + size_t aad_len; + u16 fc; + int a4_included, qc_included; + u8 aad[2 * AES_BLOCK_LEN]; + + fc = le16_to_cpu(hdr->frame_ctl); + a4_included = ((fc & (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)) == + (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)); + qc_included = ((WLAN_FC_GET_TYPE(fc) == IEEE80211_FTYPE_DATA) && + (WLAN_FC_GET_STYPE(fc) & 0x08)); + aad_len = 22; + if (a4_included) + aad_len += 6; + if (qc_included) { + pos = (u8 *) &hdr->addr4; + if (a4_included) + pos += 6; + qc = *pos & 0x0f; + aad_len += 2; + } + + /* CCM Initial Block: + * Flag (Include authentication header, M=3 (8-octet MIC), + * L=1 (2-octet Dlen)) + * Nonce: 0x00 | A2 | PN + * Dlen */ + b0[0] = 0x59; + b0[1] = qc; + memcpy(b0 + 2, hdr->addr2, ETH_ALEN); + memcpy(b0 + 8, pn, CCMP_PN_LEN); + b0[14] = (dlen >> 8) & 0xff; + b0[15] = dlen & 0xff; + + /* AAD: + * FC with bits 4..6 and 11..13 masked to zero; 14 is always one + * A1 | A2 | A3 + * SC with bits 4..15 (seq#) masked to zero + * A4 (if present) + * QC (if present) + */ + pos = (u8 *) hdr; + aad[0] = 0; /* aad_len >> 8 */ + aad[1] = aad_len & 0xff; + aad[2] = pos[0] & 0x8f; + aad[3] = pos[1] & 0xc7; + memcpy(aad + 4, hdr->addr1, 3 * ETH_ALEN); + pos = (u8 *) &hdr->seq_ctl; + aad[22] = pos[0] & 0x0f; + aad[23] = 0; /* all bits masked */ + memset(aad + 24, 0, 8); + if (a4_included) + memcpy(aad + 24, hdr->addr4, ETH_ALEN); + if (qc_included) { + aad[a4_included ? 30 : 24] = qc; + /* rest of QC masked */ + } + + /* Start with the first block and AAD */ + ieee80211_ccmp_aes_encrypt(tfm, b0, auth); + xor_block(auth, aad, AES_BLOCK_LEN); + ieee80211_ccmp_aes_encrypt(tfm, auth, auth); + xor_block(auth, &aad[AES_BLOCK_LEN], AES_BLOCK_LEN); + ieee80211_ccmp_aes_encrypt(tfm, auth, auth); + b0[0] &= 0x07; + b0[14] = b0[15] = 0; + ieee80211_ccmp_aes_encrypt(tfm, b0, s0); +} + + +static int ieee80211_ccmp_encrypt(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct ieee80211_ccmp_data *key = priv; + int data_len, i, blocks, last, len; + u8 *pos, *mic; + struct ieee80211_hdr *hdr; + u8 *b0 = key->tx_b0; + u8 *b = key->tx_b; + u8 *e = key->tx_e; + u8 *s0 = key->tx_s0; + + if (skb_headroom(skb) < CCMP_HDR_LEN || + skb_tailroom(skb) < CCMP_MIC_LEN || + skb->len < hdr_len) + return -1; + + data_len = skb->len - hdr_len; + pos = skb_push(skb, CCMP_HDR_LEN); + memmove(pos, pos + CCMP_HDR_LEN, hdr_len); + pos += hdr_len; + mic = skb_put(skb, CCMP_MIC_LEN); + + i = CCMP_PN_LEN - 1; + while (i >= 0) { + key->tx_pn[i]++; + if (key->tx_pn[i] != 0) + break; + i--; + } + + *pos++ = key->tx_pn[5]; + *pos++ = key->tx_pn[4]; + *pos++ = 0; + *pos++ = (key->key_idx << 6) | (1 << 5) /* Ext IV included */; + *pos++ = key->tx_pn[3]; + *pos++ = key->tx_pn[2]; + *pos++ = key->tx_pn[1]; + *pos++ = key->tx_pn[0]; + + hdr = (struct ieee80211_hdr *) skb->data; + ccmp_init_blocks(key->tfm, hdr, key->tx_pn, data_len, b0, b, s0); + + blocks = (data_len + AES_BLOCK_LEN - 1) / AES_BLOCK_LEN; + last = data_len % AES_BLOCK_LEN; + + for (i = 1; i <= blocks; i++) { + len = (i == blocks && last) ? last : AES_BLOCK_LEN; + /* Authentication */ + xor_block(b, pos, len); + ieee80211_ccmp_aes_encrypt(key->tfm, b, b); + /* Encryption, with counter */ + b0[14] = (i >> 8) & 0xff; + b0[15] = i & 0xff; + ieee80211_ccmp_aes_encrypt(key->tfm, b0, e); + xor_block(pos, e, len); + pos += len; + } + + for (i = 0; i < CCMP_MIC_LEN; i++) + mic[i] = b[i] ^ s0[i]; + + return 0; +} + + +static int ieee80211_ccmp_decrypt(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct ieee80211_ccmp_data *key = priv; + u8 keyidx, *pos; + struct ieee80211_hdr *hdr; + u8 *b0 = key->rx_b0; + u8 *b = key->rx_b; + u8 *a = key->rx_a; + u8 pn[6]; + int i, blocks, last, len; + size_t data_len = skb->len - hdr_len - CCMP_HDR_LEN - CCMP_MIC_LEN; + u8 *mic = skb->data + skb->len - CCMP_MIC_LEN; + + if (skb->len < hdr_len + CCMP_HDR_LEN + CCMP_MIC_LEN) { + key->dot11RSNAStatsCCMPFormatErrors++; + return -1; + } + + hdr = (struct ieee80211_hdr *) skb->data; + pos = skb->data + hdr_len; + keyidx = pos[3]; + if (!(keyidx & (1 << 5))) { + if (net_ratelimit()) { + printk(KERN_DEBUG "CCMP: received packet without ExtIV" + " flag from " MAC_FMT "\n", MAC_ARG(hdr->addr2)); + } + key->dot11RSNAStatsCCMPFormatErrors++; + return -2; + } + keyidx >>= 6; + if (key->key_idx != keyidx) { + printk(KERN_DEBUG "CCMP: RX tkey->key_idx=%d frame " + "keyidx=%d priv=%p\n", key->key_idx, keyidx, priv); + return -6; + } + if (!key->key_set) { + if (net_ratelimit()) { + printk(KERN_DEBUG "CCMP: received packet from " MAC_FMT + " with keyid=%d that does not have a configured" + " key\n", MAC_ARG(hdr->addr2), keyidx); + } + return -3; + } + + pn[0] = pos[7]; + pn[1] = pos[6]; + pn[2] = pos[5]; + pn[3] = pos[4]; + pn[4] = pos[1]; + pn[5] = pos[0]; + pos += 8; + + if (memcmp(pn, key->rx_pn, CCMP_PN_LEN) <= 0) { + if (net_ratelimit()) { + printk(KERN_DEBUG "CCMP: replay detected: STA=" MAC_FMT + " previous PN %02x%02x%02x%02x%02x%02x " + "received PN %02x%02x%02x%02x%02x%02x\n", + MAC_ARG(hdr->addr2), MAC_ARG(key->rx_pn), + MAC_ARG(pn)); + } + key->dot11RSNAStatsCCMPReplays++; + return -4; + } + + ccmp_init_blocks(key->tfm, hdr, pn, data_len, b0, a, b); + xor_block(mic, b, CCMP_MIC_LEN); + + blocks = (data_len + AES_BLOCK_LEN - 1) / AES_BLOCK_LEN; + last = data_len % AES_BLOCK_LEN; + + for (i = 1; i <= blocks; i++) { + len = (i == blocks && last) ? last : AES_BLOCK_LEN; + /* Decrypt, with counter */ + b0[14] = (i >> 8) & 0xff; + b0[15] = i & 0xff; + ieee80211_ccmp_aes_encrypt(key->tfm, b0, b); + xor_block(pos, b, len); + /* Authentication */ + xor_block(a, pos, len); + ieee80211_ccmp_aes_encrypt(key->tfm, a, a); + pos += len; + } + + if (memcmp(mic, a, CCMP_MIC_LEN) != 0) { + if (net_ratelimit()) { + printk(KERN_DEBUG "CCMP: decrypt failed: STA=" + MAC_FMT "\n", MAC_ARG(hdr->addr2)); + } + key->dot11RSNAStatsCCMPDecryptErrors++; + return -5; + } + + memcpy(key->rx_pn, pn, CCMP_PN_LEN); + + /* Remove hdr and MIC */ + memmove(skb->data + CCMP_HDR_LEN, skb->data, hdr_len); + skb_pull(skb, CCMP_HDR_LEN); + skb_trim(skb, skb->len - CCMP_MIC_LEN); + + return keyidx; +} + + +static int ieee80211_ccmp_set_key(void *key, int len, u8 *seq, void *priv) +{ + struct ieee80211_ccmp_data *data = priv; + int keyidx; + struct crypto_tfm *tfm = data->tfm; + + keyidx = data->key_idx; + memset(data, 0, sizeof(*data)); + data->key_idx = keyidx; + data->tfm = tfm; + if (len == CCMP_TK_LEN) { + memcpy(data->key, key, CCMP_TK_LEN); + data->key_set = 1; + if (seq) { + data->rx_pn[0] = seq[5]; + data->rx_pn[1] = seq[4]; + data->rx_pn[2] = seq[3]; + data->rx_pn[3] = seq[2]; + data->rx_pn[4] = seq[1]; + data->rx_pn[5] = seq[0]; + } + crypto_cipher_setkey(data->tfm, data->key, CCMP_TK_LEN); + } else if (len == 0) + data->key_set = 0; + else + return -1; + + return 0; +} + + +static int ieee80211_ccmp_get_key(void *key, int len, u8 *seq, void *priv) +{ + struct ieee80211_ccmp_data *data = priv; + + if (len < CCMP_TK_LEN) + return -1; + + if (!data->key_set) + return 0; + memcpy(key, data->key, CCMP_TK_LEN); + + if (seq) { + seq[0] = data->tx_pn[5]; + seq[1] = data->tx_pn[4]; + seq[2] = data->tx_pn[3]; + seq[3] = data->tx_pn[2]; + seq[4] = data->tx_pn[1]; + seq[5] = data->tx_pn[0]; + } + + return CCMP_TK_LEN; +} + + +static char * ieee80211_ccmp_print_stats(char *p, void *priv) +{ + struct ieee80211_ccmp_data *ccmp = priv; + p += sprintf(p, "key[%d] alg=CCMP key_set=%d " + "tx_pn=%02x%02x%02x%02x%02x%02x " + "rx_pn=%02x%02x%02x%02x%02x%02x " + "format_errors=%d replays=%d decrypt_errors=%d\n", + ccmp->key_idx, ccmp->key_set, + MAC_ARG(ccmp->tx_pn), MAC_ARG(ccmp->rx_pn), + ccmp->dot11RSNAStatsCCMPFormatErrors, + ccmp->dot11RSNAStatsCCMPReplays, + ccmp->dot11RSNAStatsCCMPDecryptErrors); + + return p; +} + + +static struct ieee80211_crypto_ops ieee80211_crypt_ccmp = { + .name = "CCMP", + .init = ieee80211_ccmp_init, + .deinit = ieee80211_ccmp_deinit, + .encrypt_mpdu = ieee80211_ccmp_encrypt, + .decrypt_mpdu = ieee80211_ccmp_decrypt, + .encrypt_msdu = NULL, + .decrypt_msdu = NULL, + .set_key = ieee80211_ccmp_set_key, + .get_key = ieee80211_ccmp_get_key, + .print_stats = ieee80211_ccmp_print_stats, + .extra_prefix_len = CCMP_HDR_LEN, + .extra_postfix_len = CCMP_MIC_LEN, + .owner = THIS_MODULE, +}; + + +static int __init ieee80211_crypto_ccmp_init(void) +{ + return ieee80211_register_crypto_ops(&ieee80211_crypt_ccmp); +} + + +static void __exit ieee80211_crypto_ccmp_exit(void) +{ + ieee80211_unregister_crypto_ops(&ieee80211_crypt_ccmp); +} + + +module_init(ieee80211_crypto_ccmp_init); +module_exit(ieee80211_crypto_ccmp_exit); diff --git a/net/ieee80211/ieee80211_crypt_tkip.c b/net/ieee80211/ieee80211_crypt_tkip.c new file mode 100644 index 000000000000..f91d92c6df25 --- /dev/null +++ b/net/ieee80211/ieee80211_crypt_tkip.c @@ -0,0 +1,708 @@ +/* + * Host AP crypt: host-based TKIP encryption implementation for Host AP driver + * + * Copyright (c) 2003-2004, Jouni Malinen <jkmaline@cc.hut.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ + +#include <linux/config.h> +#include <linux/version.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/random.h> +#include <linux/skbuff.h> +#include <linux/netdevice.h> +#include <linux/if_ether.h> +#include <linux/if_arp.h> +#include <asm/string.h> + +#include <net/ieee80211.h> + + +#include <linux/crypto.h> +#include <asm/scatterlist.h> +#include <linux/crc32.h> + +MODULE_AUTHOR("Jouni Malinen"); +MODULE_DESCRIPTION("Host AP crypt: TKIP"); +MODULE_LICENSE("GPL"); + +struct ieee80211_tkip_data { +#define TKIP_KEY_LEN 32 + u8 key[TKIP_KEY_LEN]; + int key_set; + + u32 tx_iv32; + u16 tx_iv16; + u16 tx_ttak[5]; + int tx_phase1_done; + + u32 rx_iv32; + u16 rx_iv16; + u16 rx_ttak[5]; + int rx_phase1_done; + u32 rx_iv32_new; + u16 rx_iv16_new; + + u32 dot11RSNAStatsTKIPReplays; + u32 dot11RSNAStatsTKIPICVErrors; + u32 dot11RSNAStatsTKIPLocalMICFailures; + + int key_idx; + + struct crypto_tfm *tfm_arc4; + struct crypto_tfm *tfm_michael; + + /* scratch buffers for virt_to_page() (crypto API) */ + u8 rx_hdr[16], tx_hdr[16]; +}; + +static void * ieee80211_tkip_init(int key_idx) +{ + struct ieee80211_tkip_data *priv; + + priv = kmalloc(sizeof(*priv), GFP_ATOMIC); + if (priv == NULL) + goto fail; + memset(priv, 0, sizeof(*priv)); + priv->key_idx = key_idx; + + priv->tfm_arc4 = crypto_alloc_tfm("arc4", 0); + if (priv->tfm_arc4 == NULL) { + printk(KERN_DEBUG "ieee80211_crypt_tkip: could not allocate " + "crypto API arc4\n"); + goto fail; + } + + priv->tfm_michael = crypto_alloc_tfm("michael_mic", 0); + if (priv->tfm_michael == NULL) { + printk(KERN_DEBUG "ieee80211_crypt_tkip: could not allocate " + "crypto API michael_mic\n"); + goto fail; + } + + return priv; + +fail: + if (priv) { + if (priv->tfm_michael) + crypto_free_tfm(priv->tfm_michael); + if (priv->tfm_arc4) + crypto_free_tfm(priv->tfm_arc4); + kfree(priv); + } + + return NULL; +} + + +static void ieee80211_tkip_deinit(void *priv) +{ + struct ieee80211_tkip_data *_priv = priv; + if (_priv && _priv->tfm_michael) + crypto_free_tfm(_priv->tfm_michael); + if (_priv && _priv->tfm_arc4) + crypto_free_tfm(_priv->tfm_arc4); + kfree(priv); +} + + +static inline u16 RotR1(u16 val) +{ + return (val >> 1) | (val << 15); +} + + +static inline u8 Lo8(u16 val) +{ + return val & 0xff; +} + + +static inline u8 Hi8(u16 val) +{ + return val >> 8; +} + + +static inline u16 Lo16(u32 val) +{ + return val & 0xffff; +} + + +static inline u16 Hi16(u32 val) +{ + return val >> 16; +} + + +static inline u16 Mk16(u8 hi, u8 lo) +{ + return lo | (((u16) hi) << 8); +} + + +static inline u16 Mk16_le(u16 *v) +{ + return le16_to_cpu(*v); +} + + +static const u16 Sbox[256] = +{ + 0xC6A5, 0xF884, 0xEE99, 0xF68D, 0xFF0D, 0xD6BD, 0xDEB1, 0x9154, + 0x6050, 0x0203, 0xCEA9, 0x567D, 0xE719, 0xB562, 0x4DE6, 0xEC9A, + 0x8F45, 0x1F9D, 0x8940, 0xFA87, 0xEF15, 0xB2EB, 0x8EC9, 0xFB0B, + 0x41EC, 0xB367, 0x5FFD, 0x45EA, 0x23BF, 0x53F7, 0xE496, 0x9B5B, + 0x75C2, 0xE11C, 0x3DAE, 0x4C6A, 0x6C5A, 0x7E41, 0xF502, 0x834F, + 0x685C, 0x51F4, 0xD134, 0xF908, 0xE293, 0xAB73, 0x6253, 0x2A3F, + 0x080C, 0x9552, 0x4665, 0x9D5E, 0x3028, 0x37A1, 0x0A0F, 0x2FB5, + 0x0E09, 0x2436, 0x1B9B, 0xDF3D, 0xCD26, 0x4E69, 0x7FCD, 0xEA9F, + 0x121B, 0x1D9E, 0x5874, 0x342E, 0x362D, 0xDCB2, 0xB4EE, 0x5BFB, + 0xA4F6, 0x764D, 0xB761, 0x7DCE, 0x527B, 0xDD3E, 0x5E71, 0x1397, + 0xA6F5, 0xB968, 0x0000, 0xC12C, 0x4060, 0xE31F, 0x79C8, 0xB6ED, + 0xD4BE, 0x8D46, 0x67D9, 0x724B, 0x94DE, 0x98D4, 0xB0E8, 0x854A, + 0xBB6B, 0xC52A, 0x4FE5, 0xED16, 0x86C5, 0x9AD7, 0x6655, 0x1194, + 0x8ACF, 0xE910, 0x0406, 0xFE81, 0xA0F0, 0x7844, 0x25BA, 0x4BE3, + 0xA2F3, 0x5DFE, 0x80C0, 0x058A, 0x3FAD, 0x21BC, 0x7048, 0xF104, + 0x63DF, 0x77C1, 0xAF75, 0x4263, 0x2030, 0xE51A, 0xFD0E, 0xBF6D, + 0x814C, 0x1814, 0x2635, 0xC32F, 0xBEE1, 0x35A2, 0x88CC, 0x2E39, + 0x9357, 0x55F2, 0xFC82, 0x7A47, 0xC8AC, 0xBAE7, 0x322B, 0xE695, + 0xC0A0, 0x1998, 0x9ED1, 0xA37F, 0x4466, 0x547E, 0x3BAB, 0x0B83, + 0x8CCA, 0xC729, 0x6BD3, 0x283C, 0xA779, 0xBCE2, 0x161D, 0xAD76, + 0xDB3B, 0x6456, 0x744E, 0x141E, 0x92DB, 0x0C0A, 0x486C, 0xB8E4, + 0x9F5D, 0xBD6E, 0x43EF, 0xC4A6, 0x39A8, 0x31A4, 0xD337, 0xF28B, + 0xD532, 0x8B43, 0x6E59, 0xDAB7, 0x018C, 0xB164, 0x9CD2, 0x49E0, + 0xD8B4, 0xACFA, 0xF307, 0xCF25, 0xCAAF, 0xF48E, 0x47E9, 0x1018, + 0x6FD5, 0xF088, 0x4A6F, 0x5C72, 0x3824, 0x57F1, 0x73C7, 0x9751, + 0xCB23, 0xA17C, 0xE89C, 0x3E21, 0x96DD, 0x61DC, 0x0D86, 0x0F85, + 0xE090, 0x7C42, 0x71C4, 0xCCAA, 0x90D8, 0x0605, 0xF701, 0x1C12, + 0xC2A3, 0x6A5F, 0xAEF9, 0x69D0, 0x1791, 0x9958, 0x3A27, 0x27B9, + 0xD938, 0xEB13, 0x2BB3, 0x2233, 0xD2BB, 0xA970, 0x0789, 0x33A7, + 0x2DB6, 0x3C22, 0x1592, 0xC920, 0x8749, 0xAAFF, 0x5078, 0xA57A, + 0x038F, 0x59F8, 0x0980, 0x1A17, 0x65DA, 0xD731, 0x84C6, 0xD0B8, + 0x82C3, 0x29B0, 0x5A77, 0x1E11, 0x7BCB, 0xA8FC, 0x6DD6, 0x2C3A, +}; + + +static inline u16 _S_(u16 v) +{ + u16 t = Sbox[Hi8(v)]; + return Sbox[Lo8(v)] ^ ((t << 8) | (t >> 8)); +} + + +#define PHASE1_LOOP_COUNT 8 + +static void tkip_mixing_phase1(u16 *TTAK, const u8 *TK, const u8 *TA, u32 IV32) +{ + int i, j; + + /* Initialize the 80-bit TTAK from TSC (IV32) and TA[0..5] */ + TTAK[0] = Lo16(IV32); + TTAK[1] = Hi16(IV32); + TTAK[2] = Mk16(TA[1], TA[0]); + TTAK[3] = Mk16(TA[3], TA[2]); + TTAK[4] = Mk16(TA[5], TA[4]); + + for (i = 0; i < PHASE1_LOOP_COUNT; i++) { + j = 2 * (i & 1); + TTAK[0] += _S_(TTAK[4] ^ Mk16(TK[1 + j], TK[0 + j])); + TTAK[1] += _S_(TTAK[0] ^ Mk16(TK[5 + j], TK[4 + j])); + TTAK[2] += _S_(TTAK[1] ^ Mk16(TK[9 + j], TK[8 + j])); + TTAK[3] += _S_(TTAK[2] ^ Mk16(TK[13 + j], TK[12 + j])); + TTAK[4] += _S_(TTAK[3] ^ Mk16(TK[1 + j], TK[0 + j])) + i; + } +} + + +static void tkip_mixing_phase2(u8 *WEPSeed, const u8 *TK, const u16 *TTAK, + u16 IV16) +{ + /* Make temporary area overlap WEP seed so that the final copy can be + * avoided on little endian hosts. */ + u16 *PPK = (u16 *) &WEPSeed[4]; + + /* Step 1 - make copy of TTAK and bring in TSC */ + PPK[0] = TTAK[0]; + PPK[1] = TTAK[1]; + PPK[2] = TTAK[2]; + PPK[3] = TTAK[3]; + PPK[4] = TTAK[4]; + PPK[5] = TTAK[4] + IV16; + + /* Step 2 - 96-bit bijective mixing using S-box */ + PPK[0] += _S_(PPK[5] ^ Mk16_le((u16 *) &TK[0])); + PPK[1] += _S_(PPK[0] ^ Mk16_le((u16 *) &TK[2])); + PPK[2] += _S_(PPK[1] ^ Mk16_le((u16 *) &TK[4])); + PPK[3] += _S_(PPK[2] ^ Mk16_le((u16 *) &TK[6])); + PPK[4] += _S_(PPK[3] ^ Mk16_le((u16 *) &TK[8])); + PPK[5] += _S_(PPK[4] ^ Mk16_le((u16 *) &TK[10])); + + PPK[0] += RotR1(PPK[5] ^ Mk16_le((u16 *) &TK[12])); + PPK[1] += RotR1(PPK[0] ^ Mk16_le((u16 *) &TK[14])); + PPK[2] += RotR1(PPK[1]); + PPK[3] += RotR1(PPK[2]); + PPK[4] += RotR1(PPK[3]); + PPK[5] += RotR1(PPK[4]); + + /* Step 3 - bring in last of TK bits, assign 24-bit WEP IV value + * WEPSeed[0..2] is transmitted as WEP IV */ + WEPSeed[0] = Hi8(IV16); + WEPSeed[1] = (Hi8(IV16) | 0x20) & 0x7F; + WEPSeed[2] = Lo8(IV16); + WEPSeed[3] = Lo8((PPK[5] ^ Mk16_le((u16 *) &TK[0])) >> 1); + +#ifdef __BIG_ENDIAN + { + int i; + for (i = 0; i < 6; i++) + PPK[i] = (PPK[i] << 8) | (PPK[i] >> 8); + } +#endif +} + +static int ieee80211_tkip_encrypt(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct ieee80211_tkip_data *tkey = priv; + int len; + u8 rc4key[16], *pos, *icv; + struct ieee80211_hdr *hdr; + u32 crc; + struct scatterlist sg; + + if (skb_headroom(skb) < 8 || skb_tailroom(skb) < 4 || + skb->len < hdr_len) + return -1; + + hdr = (struct ieee80211_hdr *) skb->data; + if (!tkey->tx_phase1_done) { + tkip_mixing_phase1(tkey->tx_ttak, tkey->key, hdr->addr2, + tkey->tx_iv32); + tkey->tx_phase1_done = 1; + } + tkip_mixing_phase2(rc4key, tkey->key, tkey->tx_ttak, tkey->tx_iv16); + + len = skb->len - hdr_len; + pos = skb_push(skb, 8); + memmove(pos, pos + 8, hdr_len); + pos += hdr_len; + icv = skb_put(skb, 4); + + *pos++ = rc4key[0]; + *pos++ = rc4key[1]; + *pos++ = rc4key[2]; + *pos++ = (tkey->key_idx << 6) | (1 << 5) /* Ext IV included */; + *pos++ = tkey->tx_iv32 & 0xff; + *pos++ = (tkey->tx_iv32 >> 8) & 0xff; + *pos++ = (tkey->tx_iv32 >> 16) & 0xff; + *pos++ = (tkey->tx_iv32 >> 24) & 0xff; + + crc = ~crc32_le(~0, pos, len); + icv[0] = crc; + icv[1] = crc >> 8; + icv[2] = crc >> 16; + icv[3] = crc >> 24; + + crypto_cipher_setkey(tkey->tfm_arc4, rc4key, 16); + sg.page = virt_to_page(pos); + sg.offset = offset_in_page(pos); + sg.length = len + 4; + crypto_cipher_encrypt(tkey->tfm_arc4, &sg, &sg, len + 4); + + tkey->tx_iv16++; + if (tkey->tx_iv16 == 0) { + tkey->tx_phase1_done = 0; + tkey->tx_iv32++; + } + + return 0; +} + +static int ieee80211_tkip_decrypt(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct ieee80211_tkip_data *tkey = priv; + u8 rc4key[16]; + u8 keyidx, *pos; + u32 iv32; + u16 iv16; + struct ieee80211_hdr *hdr; + u8 icv[4]; + u32 crc; + struct scatterlist sg; + int plen; + + if (skb->len < hdr_len + 8 + 4) + return -1; + + hdr = (struct ieee80211_hdr *) skb->data; + pos = skb->data + hdr_len; + keyidx = pos[3]; + if (!(keyidx & (1 << 5))) { + if (net_ratelimit()) { + printk(KERN_DEBUG "TKIP: received packet without ExtIV" + " flag from " MAC_FMT "\n", MAC_ARG(hdr->addr2)); + } + return -2; + } + keyidx >>= 6; + if (tkey->key_idx != keyidx) { + printk(KERN_DEBUG "TKIP: RX tkey->key_idx=%d frame " + "keyidx=%d priv=%p\n", tkey->key_idx, keyidx, priv); + return -6; + } + if (!tkey->key_set) { + if (net_ratelimit()) { + printk(KERN_DEBUG "TKIP: received packet from " MAC_FMT + " with keyid=%d that does not have a configured" + " key\n", MAC_ARG(hdr->addr2), keyidx); + } + return -3; + } + iv16 = (pos[0] << 8) | pos[2]; + iv32 = pos[4] | (pos[5] << 8) | (pos[6] << 16) | (pos[7] << 24); + pos += 8; + + if (iv32 < tkey->rx_iv32 || + (iv32 == tkey->rx_iv32 && iv16 <= tkey->rx_iv16)) { + if (net_ratelimit()) { + printk(KERN_DEBUG "TKIP: replay detected: STA=" MAC_FMT + " previous TSC %08x%04x received TSC " + "%08x%04x\n", MAC_ARG(hdr->addr2), + tkey->rx_iv32, tkey->rx_iv16, iv32, iv16); + } + tkey->dot11RSNAStatsTKIPReplays++; + return -4; + } + + if (iv32 != tkey->rx_iv32 || !tkey->rx_phase1_done) { + tkip_mixing_phase1(tkey->rx_ttak, tkey->key, hdr->addr2, iv32); + tkey->rx_phase1_done = 1; + } + tkip_mixing_phase2(rc4key, tkey->key, tkey->rx_ttak, iv16); + + plen = skb->len - hdr_len - 12; + + crypto_cipher_setkey(tkey->tfm_arc4, rc4key, 16); + sg.page = virt_to_page(pos); + sg.offset = offset_in_page(pos); + sg.length = plen + 4; + crypto_cipher_decrypt(tkey->tfm_arc4, &sg, &sg, plen + 4); + + crc = ~crc32_le(~0, pos, plen); + icv[0] = crc; + icv[1] = crc >> 8; + icv[2] = crc >> 16; + icv[3] = crc >> 24; + if (memcmp(icv, pos + plen, 4) != 0) { + if (iv32 != tkey->rx_iv32) { + /* Previously cached Phase1 result was already lost, so + * it needs to be recalculated for the next packet. */ + tkey->rx_phase1_done = 0; + } + if (net_ratelimit()) { + printk(KERN_DEBUG "TKIP: ICV error detected: STA=" + MAC_FMT "\n", MAC_ARG(hdr->addr2)); + } + tkey->dot11RSNAStatsTKIPICVErrors++; + return -5; + } + + /* Update real counters only after Michael MIC verification has + * completed */ + tkey->rx_iv32_new = iv32; + tkey->rx_iv16_new = iv16; + + /* Remove IV and ICV */ + memmove(skb->data + 8, skb->data, hdr_len); + skb_pull(skb, 8); + skb_trim(skb, skb->len - 4); + + return keyidx; +} + + +static int michael_mic(struct ieee80211_tkip_data *tkey, u8 *key, u8 *hdr, + u8 *data, size_t data_len, u8 *mic) +{ + struct scatterlist sg[2]; + + if (tkey->tfm_michael == NULL) { + printk(KERN_WARNING "michael_mic: tfm_michael == NULL\n"); + return -1; + } + sg[0].page = virt_to_page(hdr); + sg[0].offset = offset_in_page(hdr); + sg[0].length = 16; + + sg[1].page = virt_to_page(data); + sg[1].offset = offset_in_page(data); + sg[1].length = data_len; + + crypto_digest_init(tkey->tfm_michael); + crypto_digest_setkey(tkey->tfm_michael, key, 8); + crypto_digest_update(tkey->tfm_michael, sg, 2); + crypto_digest_final(tkey->tfm_michael, mic); + + return 0; +} + +static void michael_mic_hdr(struct sk_buff *skb, u8 *hdr) +{ + struct ieee80211_hdr *hdr11; + + hdr11 = (struct ieee80211_hdr *) skb->data; + switch (le16_to_cpu(hdr11->frame_ctl) & + (IEEE80211_FCTL_FROMDS | IEEE80211_FCTL_TODS)) { + case IEEE80211_FCTL_TODS: + memcpy(hdr, hdr11->addr3, ETH_ALEN); /* DA */ + memcpy(hdr + ETH_ALEN, hdr11->addr2, ETH_ALEN); /* SA */ + break; + case IEEE80211_FCTL_FROMDS: + memcpy(hdr, hdr11->addr1, ETH_ALEN); /* DA */ + memcpy(hdr + ETH_ALEN, hdr11->addr3, ETH_ALEN); /* SA */ + break; + case IEEE80211_FCTL_FROMDS | IEEE80211_FCTL_TODS: + memcpy(hdr, hdr11->addr3, ETH_ALEN); /* DA */ + memcpy(hdr + ETH_ALEN, hdr11->addr4, ETH_ALEN); /* SA */ + break; + case 0: + memcpy(hdr, hdr11->addr1, ETH_ALEN); /* DA */ + memcpy(hdr + ETH_ALEN, hdr11->addr2, ETH_ALEN); /* SA */ + break; + } + + hdr[12] = 0; /* priority */ + hdr[13] = hdr[14] = hdr[15] = 0; /* reserved */ +} + + +static int ieee80211_michael_mic_add(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct ieee80211_tkip_data *tkey = priv; + u8 *pos; + + if (skb_tailroom(skb) < 8 || skb->len < hdr_len) { + printk(KERN_DEBUG "Invalid packet for Michael MIC add " + "(tailroom=%d hdr_len=%d skb->len=%d)\n", + skb_tailroom(skb), hdr_len, skb->len); + return -1; + } + + michael_mic_hdr(skb, tkey->tx_hdr); + pos = skb_put(skb, 8); + if (michael_mic(tkey, &tkey->key[16], tkey->tx_hdr, + skb->data + hdr_len, skb->len - 8 - hdr_len, pos)) + return -1; + + return 0; +} + + +#if WIRELESS_EXT >= 18 +static void ieee80211_michael_mic_failure(struct net_device *dev, + struct ieee80211_hdr *hdr, + int keyidx) +{ + union iwreq_data wrqu; + struct iw_michaelmicfailure ev; + + /* TODO: needed parameters: count, keyid, key type, TSC */ + memset(&ev, 0, sizeof(ev)); + ev.flags = keyidx & IW_MICFAILURE_KEY_ID; + if (hdr->addr1[0] & 0x01) + ev.flags |= IW_MICFAILURE_GROUP; + else + ev.flags |= IW_MICFAILURE_PAIRWISE; + ev.src_addr.sa_family = ARPHRD_ETHER; + memcpy(ev.src_addr.sa_data, hdr->addr2, ETH_ALEN); + memset(&wrqu, 0, sizeof(wrqu)); + wrqu.data.length = sizeof(ev); + wireless_send_event(dev, IWEVMICHAELMICFAILURE, &wrqu, (char *) &ev); +} +#elif WIRELESS_EXT >= 15 +static void ieee80211_michael_mic_failure(struct net_device *dev, + struct ieee80211_hdr *hdr, + int keyidx) +{ + union iwreq_data wrqu; + char buf[128]; + + /* TODO: needed parameters: count, keyid, key type, TSC */ + sprintf(buf, "MLME-MICHAELMICFAILURE.indication(keyid=%d %scast addr=" + MAC_FMT ")", keyidx, hdr->addr1[0] & 0x01 ? "broad" : "uni", + MAC_ARG(hdr->addr2)); + memset(&wrqu, 0, sizeof(wrqu)); + wrqu.data.length = strlen(buf); + wireless_send_event(dev, IWEVCUSTOM, &wrqu, buf); +} +#else /* WIRELESS_EXT >= 15 */ +static inline void ieee80211_michael_mic_failure(struct net_device *dev, + struct ieee80211_hdr *hdr, + int keyidx) +{ +} +#endif /* WIRELESS_EXT >= 15 */ + + +static int ieee80211_michael_mic_verify(struct sk_buff *skb, int keyidx, + int hdr_len, void *priv) +{ + struct ieee80211_tkip_data *tkey = priv; + u8 mic[8]; + + if (!tkey->key_set) + return -1; + + michael_mic_hdr(skb, tkey->rx_hdr); + if (michael_mic(tkey, &tkey->key[24], tkey->rx_hdr, + skb->data + hdr_len, skb->len - 8 - hdr_len, mic)) + return -1; + if (memcmp(mic, skb->data + skb->len - 8, 8) != 0) { + struct ieee80211_hdr *hdr; + hdr = (struct ieee80211_hdr *) skb->data; + printk(KERN_DEBUG "%s: Michael MIC verification failed for " + "MSDU from " MAC_FMT " keyidx=%d\n", + skb->dev ? skb->dev->name : "N/A", MAC_ARG(hdr->addr2), + keyidx); + if (skb->dev) + ieee80211_michael_mic_failure(skb->dev, hdr, keyidx); + tkey->dot11RSNAStatsTKIPLocalMICFailures++; + return -1; + } + + /* Update TSC counters for RX now that the packet verification has + * completed. */ + tkey->rx_iv32 = tkey->rx_iv32_new; + tkey->rx_iv16 = tkey->rx_iv16_new; + + skb_trim(skb, skb->len - 8); + + return 0; +} + + +static int ieee80211_tkip_set_key(void *key, int len, u8 *seq, void *priv) +{ + struct ieee80211_tkip_data *tkey = priv; + int keyidx; + struct crypto_tfm *tfm = tkey->tfm_michael; + struct crypto_tfm *tfm2 = tkey->tfm_arc4; + + keyidx = tkey->key_idx; + memset(tkey, 0, sizeof(*tkey)); + tkey->key_idx = keyidx; + tkey->tfm_michael = tfm; + tkey->tfm_arc4 = tfm2; + if (len == TKIP_KEY_LEN) { + memcpy(tkey->key, key, TKIP_KEY_LEN); + tkey->key_set = 1; + tkey->tx_iv16 = 1; /* TSC is initialized to 1 */ + if (seq) { + tkey->rx_iv32 = (seq[5] << 24) | (seq[4] << 16) | + (seq[3] << 8) | seq[2]; + tkey->rx_iv16 = (seq[1] << 8) | seq[0]; + } + } else if (len == 0) + tkey->key_set = 0; + else + return -1; + + return 0; +} + + +static int ieee80211_tkip_get_key(void *key, int len, u8 *seq, void *priv) +{ + struct ieee80211_tkip_data *tkey = priv; + + if (len < TKIP_KEY_LEN) + return -1; + + if (!tkey->key_set) + return 0; + memcpy(key, tkey->key, TKIP_KEY_LEN); + + if (seq) { + /* Return the sequence number of the last transmitted frame. */ + u16 iv16 = tkey->tx_iv16; + u32 iv32 = tkey->tx_iv32; + if (iv16 == 0) + iv32--; + iv16--; + seq[0] = tkey->tx_iv16; + seq[1] = tkey->tx_iv16 >> 8; + seq[2] = tkey->tx_iv32; + seq[3] = tkey->tx_iv32 >> 8; + seq[4] = tkey->tx_iv32 >> 16; + seq[5] = tkey->tx_iv32 >> 24; + } + + return TKIP_KEY_LEN; +} + + +static char * ieee80211_tkip_print_stats(char *p, void *priv) +{ + struct ieee80211_tkip_data *tkip = priv; + p += sprintf(p, "key[%d] alg=TKIP key_set=%d " + "tx_pn=%02x%02x%02x%02x%02x%02x " + "rx_pn=%02x%02x%02x%02x%02x%02x " + "replays=%d icv_errors=%d local_mic_failures=%d\n", + tkip->key_idx, tkip->key_set, + (tkip->tx_iv32 >> 24) & 0xff, + (tkip->tx_iv32 >> 16) & 0xff, + (tkip->tx_iv32 >> 8) & 0xff, + tkip->tx_iv32 & 0xff, + (tkip->tx_iv16 >> 8) & 0xff, + tkip->tx_iv16 & 0xff, + (tkip->rx_iv32 >> 24) & 0xff, + (tkip->rx_iv32 >> 16) & 0xff, + (tkip->rx_iv32 >> 8) & 0xff, + tkip->rx_iv32 & 0xff, + (tkip->rx_iv16 >> 8) & 0xff, + tkip->rx_iv16 & 0xff, + tkip->dot11RSNAStatsTKIPReplays, + tkip->dot11RSNAStatsTKIPICVErrors, + tkip->dot11RSNAStatsTKIPLocalMICFailures); + return p; +} + + +static struct ieee80211_crypto_ops ieee80211_crypt_tkip = { + .name = "TKIP", + .init = ieee80211_tkip_init, + .deinit = ieee80211_tkip_deinit, + .encrypt_mpdu = ieee80211_tkip_encrypt, + .decrypt_mpdu = ieee80211_tkip_decrypt, + .encrypt_msdu = ieee80211_michael_mic_add, + .decrypt_msdu = ieee80211_michael_mic_verify, + .set_key = ieee80211_tkip_set_key, + .get_key = ieee80211_tkip_get_key, + .print_stats = ieee80211_tkip_print_stats, + .extra_prefix_len = 4 + 4, /* IV + ExtIV */ + .extra_postfix_len = 8 + 4, /* MIC + ICV */ + .owner = THIS_MODULE, +}; + + +static int __init ieee80211_crypto_tkip_init(void) +{ + return ieee80211_register_crypto_ops(&ieee80211_crypt_tkip); +} + + +static void __exit ieee80211_crypto_tkip_exit(void) +{ + ieee80211_unregister_crypto_ops(&ieee80211_crypt_tkip); +} + + +module_init(ieee80211_crypto_tkip_init); +module_exit(ieee80211_crypto_tkip_exit); diff --git a/net/ieee80211/ieee80211_crypt_wep.c b/net/ieee80211/ieee80211_crypt_wep.c new file mode 100644 index 000000000000..bec1d3470d39 --- /dev/null +++ b/net/ieee80211/ieee80211_crypt_wep.c @@ -0,0 +1,272 @@ +/* + * Host AP crypt: host-based WEP encryption implementation for Host AP driver + * + * Copyright (c) 2002-2004, Jouni Malinen <jkmaline@cc.hut.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ + +#include <linux/config.h> +#include <linux/version.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/random.h> +#include <linux/skbuff.h> +#include <asm/string.h> + +#include <net/ieee80211.h> + + +#include <linux/crypto.h> +#include <asm/scatterlist.h> +#include <linux/crc32.h> + +MODULE_AUTHOR("Jouni Malinen"); +MODULE_DESCRIPTION("Host AP crypt: WEP"); +MODULE_LICENSE("GPL"); + + +struct prism2_wep_data { + u32 iv; +#define WEP_KEY_LEN 13 + u8 key[WEP_KEY_LEN + 1]; + u8 key_len; + u8 key_idx; + struct crypto_tfm *tfm; +}; + + +static void * prism2_wep_init(int keyidx) +{ + struct prism2_wep_data *priv; + + priv = kmalloc(sizeof(*priv), GFP_ATOMIC); + if (priv == NULL) + goto fail; + memset(priv, 0, sizeof(*priv)); + priv->key_idx = keyidx; + + priv->tfm = crypto_alloc_tfm("arc4", 0); + if (priv->tfm == NULL) { + printk(KERN_DEBUG "ieee80211_crypt_wep: could not allocate " + "crypto API arc4\n"); + goto fail; + } + + /* start WEP IV from a random value */ + get_random_bytes(&priv->iv, 4); + + return priv; + +fail: + if (priv) { + if (priv->tfm) + crypto_free_tfm(priv->tfm); + kfree(priv); + } + return NULL; +} + + +static void prism2_wep_deinit(void *priv) +{ + struct prism2_wep_data *_priv = priv; + if (_priv && _priv->tfm) + crypto_free_tfm(_priv->tfm); + kfree(priv); +} + + +/* Perform WEP encryption on given skb that has at least 4 bytes of headroom + * for IV and 4 bytes of tailroom for ICV. Both IV and ICV will be transmitted, + * so the payload length increases with 8 bytes. + * + * WEP frame payload: IV + TX key idx, RC4(data), ICV = RC4(CRC32(data)) + */ +static int prism2_wep_encrypt(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct prism2_wep_data *wep = priv; + u32 crc, klen, len; + u8 key[WEP_KEY_LEN + 3]; + u8 *pos, *icv; + struct scatterlist sg; + + if (skb_headroom(skb) < 4 || skb_tailroom(skb) < 4 || + skb->len < hdr_len) + return -1; + + len = skb->len - hdr_len; + pos = skb_push(skb, 4); + memmove(pos, pos + 4, hdr_len); + pos += hdr_len; + + klen = 3 + wep->key_len; + + wep->iv++; + + /* Fluhrer, Mantin, and Shamir have reported weaknesses in the key + * scheduling algorithm of RC4. At least IVs (KeyByte + 3, 0xff, N) + * can be used to speedup attacks, so avoid using them. */ + if ((wep->iv & 0xff00) == 0xff00) { + u8 B = (wep->iv >> 16) & 0xff; + if (B >= 3 && B < klen) + wep->iv += 0x0100; + } + + /* Prepend 24-bit IV to RC4 key and TX frame */ + *pos++ = key[0] = (wep->iv >> 16) & 0xff; + *pos++ = key[1] = (wep->iv >> 8) & 0xff; + *pos++ = key[2] = wep->iv & 0xff; + *pos++ = wep->key_idx << 6; + + /* Copy rest of the WEP key (the secret part) */ + memcpy(key + 3, wep->key, wep->key_len); + + /* Append little-endian CRC32 and encrypt it to produce ICV */ + crc = ~crc32_le(~0, pos, len); + icv = skb_put(skb, 4); + icv[0] = crc; + icv[1] = crc >> 8; + icv[2] = crc >> 16; + icv[3] = crc >> 24; + + crypto_cipher_setkey(wep->tfm, key, klen); + sg.page = virt_to_page(pos); + sg.offset = offset_in_page(pos); + sg.length = len + 4; + crypto_cipher_encrypt(wep->tfm, &sg, &sg, len + 4); + + return 0; +} + + +/* Perform WEP decryption on given buffer. Buffer includes whole WEP part of + * the frame: IV (4 bytes), encrypted payload (including SNAP header), + * ICV (4 bytes). len includes both IV and ICV. + * + * Returns 0 if frame was decrypted successfully and ICV was correct and -1 on + * failure. If frame is OK, IV and ICV will be removed. + */ +static int prism2_wep_decrypt(struct sk_buff *skb, int hdr_len, void *priv) +{ + struct prism2_wep_data *wep = priv; + u32 crc, klen, plen; + u8 key[WEP_KEY_LEN + 3]; + u8 keyidx, *pos, icv[4]; + struct scatterlist sg; + + if (skb->len < hdr_len + 8) + return -1; + + pos = skb->data + hdr_len; + key[0] = *pos++; + key[1] = *pos++; + key[2] = *pos++; + keyidx = *pos++ >> 6; + if (keyidx != wep->key_idx) + return -1; + + klen = 3 + wep->key_len; + + /* Copy rest of the WEP key (the secret part) */ + memcpy(key + 3, wep->key, wep->key_len); + + /* Apply RC4 to data and compute CRC32 over decrypted data */ + plen = skb->len - hdr_len - 8; + + crypto_cipher_setkey(wep->tfm, key, klen); + sg.page = virt_to_page(pos); + sg.offset = offset_in_page(pos); + sg.length = plen + 4; + crypto_cipher_decrypt(wep->tfm, &sg, &sg, plen + 4); + + crc = ~crc32_le(~0, pos, plen); + icv[0] = crc; + icv[1] = crc >> 8; + icv[2] = crc >> 16; + icv[3] = crc >> 24; + if (memcmp(icv, pos + plen, 4) != 0) { + /* ICV mismatch - drop frame */ + return -2; + } + + /* Remove IV and ICV */ + memmove(skb->data + 4, skb->data, hdr_len); + skb_pull(skb, 4); + skb_trim(skb, skb->len - 4); + + return 0; +} + + +static int prism2_wep_set_key(void *key, int len, u8 *seq, void *priv) +{ + struct prism2_wep_data *wep = priv; + + if (len < 0 || len > WEP_KEY_LEN) + return -1; + + memcpy(wep->key, key, len); + wep->key_len = len; + + return 0; +} + + +static int prism2_wep_get_key(void *key, int len, u8 *seq, void *priv) +{ + struct prism2_wep_data *wep = priv; + + if (len < wep->key_len) + return -1; + + memcpy(key, wep->key, wep->key_len); + + return wep->key_len; +} + + +static char * prism2_wep_print_stats(char *p, void *priv) +{ + struct prism2_wep_data *wep = priv; + p += sprintf(p, "key[%d] alg=WEP len=%d\n", + wep->key_idx, wep->key_len); + return p; +} + + +static struct ieee80211_crypto_ops ieee80211_crypt_wep = { + .name = "WEP", + .init = prism2_wep_init, + .deinit = prism2_wep_deinit, + .encrypt_mpdu = prism2_wep_encrypt, + .decrypt_mpdu = prism2_wep_decrypt, + .encrypt_msdu = NULL, + .decrypt_msdu = NULL, + .set_key = prism2_wep_set_key, + .get_key = prism2_wep_get_key, + .print_stats = prism2_wep_print_stats, + .extra_prefix_len = 4, /* IV */ + .extra_postfix_len = 4, /* ICV */ + .owner = THIS_MODULE, +}; + + +static int __init ieee80211_crypto_wep_init(void) +{ + return ieee80211_register_crypto_ops(&ieee80211_crypt_wep); +} + + +static void __exit ieee80211_crypto_wep_exit(void) +{ + ieee80211_unregister_crypto_ops(&ieee80211_crypt_wep); +} + + +module_init(ieee80211_crypto_wep_init); +module_exit(ieee80211_crypto_wep_exit); diff --git a/net/ieee80211/ieee80211_module.c b/net/ieee80211/ieee80211_module.c new file mode 100644 index 000000000000..e4ca0daaaeea --- /dev/null +++ b/net/ieee80211/ieee80211_module.c @@ -0,0 +1,268 @@ +/******************************************************************************* + + Copyright(c) 2004 Intel Corporation. All rights reserved. + + Portions of this file are based on the WEP enablement code provided by the + Host AP project hostap-drivers v0.1.3 + Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + <jkmaline@cc.hut.fi> + Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +#include <linux/compiler.h> +#include <linux/config.h> +#include <linux/errno.h> +#include <linux/if_arp.h> +#include <linux/in6.h> +#include <linux/in.h> +#include <linux/ip.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/pci.h> +#include <linux/proc_fs.h> +#include <linux/skbuff.h> +#include <linux/slab.h> +#include <linux/tcp.h> +#include <linux/types.h> +#include <linux/version.h> +#include <linux/wireless.h> +#include <linux/etherdevice.h> +#include <asm/uaccess.h> +#include <net/arp.h> + +#include <net/ieee80211.h> + +MODULE_DESCRIPTION("802.11 data/management/control stack"); +MODULE_AUTHOR("Copyright (C) 2004 Intel Corporation <jketreno@linux.intel.com>"); +MODULE_LICENSE("GPL"); + +#define DRV_NAME "ieee80211" + +static inline int ieee80211_networks_allocate(struct ieee80211_device *ieee) +{ + if (ieee->networks) + return 0; + + ieee->networks = kmalloc( + MAX_NETWORK_COUNT * sizeof(struct ieee80211_network), + GFP_KERNEL); + if (!ieee->networks) { + printk(KERN_WARNING "%s: Out of memory allocating beacons\n", + ieee->dev->name); + return -ENOMEM; + } + + memset(ieee->networks, 0, + MAX_NETWORK_COUNT * sizeof(struct ieee80211_network)); + + return 0; +} + +static inline void ieee80211_networks_free(struct ieee80211_device *ieee) +{ + if (!ieee->networks) + return; + kfree(ieee->networks); + ieee->networks = NULL; +} + +static inline void ieee80211_networks_initialize(struct ieee80211_device *ieee) +{ + int i; + + INIT_LIST_HEAD(&ieee->network_free_list); + INIT_LIST_HEAD(&ieee->network_list); + for (i = 0; i < MAX_NETWORK_COUNT; i++) + list_add_tail(&ieee->networks[i].list, &ieee->network_free_list); +} + + +struct net_device *alloc_ieee80211(int sizeof_priv) +{ + struct ieee80211_device *ieee; + struct net_device *dev; + int err; + + IEEE80211_DEBUG_INFO("Initializing...\n"); + + dev = alloc_etherdev(sizeof(struct ieee80211_device) + sizeof_priv); + if (!dev) { + IEEE80211_ERROR("Unable to network device.\n"); + goto failed; + } + ieee = netdev_priv(dev); + dev->hard_start_xmit = ieee80211_xmit; + + ieee->dev = dev; + + err = ieee80211_networks_allocate(ieee); + if (err) { + IEEE80211_ERROR("Unable to allocate beacon storage: %d\n", + err); + goto failed; + } + ieee80211_networks_initialize(ieee); + + /* Default fragmentation threshold is maximum payload size */ + ieee->fts = DEFAULT_FTS; + ieee->scan_age = DEFAULT_MAX_SCAN_AGE; + ieee->open_wep = 1; + + /* Default to enabling full open WEP with host based encrypt/decrypt */ + ieee->host_encrypt = 1; + ieee->host_decrypt = 1; + ieee->ieee802_1x = 1; /* Default to supporting 802.1x */ + + INIT_LIST_HEAD(&ieee->crypt_deinit_list); + init_timer(&ieee->crypt_deinit_timer); + ieee->crypt_deinit_timer.data = (unsigned long)ieee; + ieee->crypt_deinit_timer.function = ieee80211_crypt_deinit_handler; + + spin_lock_init(&ieee->lock); + + ieee->wpa_enabled = 0; + ieee->tkip_countermeasures = 0; + ieee->drop_unencrypted = 0; + ieee->privacy_invoked = 0; + ieee->ieee802_1x = 1; + + return dev; + + failed: + if (dev) + free_netdev(dev); + return NULL; +} + + +void free_ieee80211(struct net_device *dev) +{ + struct ieee80211_device *ieee = netdev_priv(dev); + + int i; + + del_timer_sync(&ieee->crypt_deinit_timer); + ieee80211_crypt_deinit_entries(ieee, 1); + + for (i = 0; i < WEP_KEYS; i++) { + struct ieee80211_crypt_data *crypt = ieee->crypt[i]; + if (crypt) { + if (crypt->ops) { + crypt->ops->deinit(crypt->priv); + module_put(crypt->ops->owner); + } + kfree(crypt); + ieee->crypt[i] = NULL; + } + } + + ieee80211_networks_free(ieee); + free_netdev(dev); +} + +#ifdef CONFIG_IEEE80211_DEBUG + +static int debug = 0; +u32 ieee80211_debug_level = 0; +struct proc_dir_entry *ieee80211_proc = NULL; + +static int show_debug_level(char *page, char **start, off_t offset, + int count, int *eof, void *data) +{ + return snprintf(page, count, "0x%08X\n", ieee80211_debug_level); +} + +static int store_debug_level(struct file *file, const char *buffer, + unsigned long count, void *data) +{ + char buf[] = "0x00000000"; + unsigned long len = min(sizeof(buf) - 1, (u32)count); + char *p = (char *)buf; + unsigned long val; + + if (copy_from_user(buf, buffer, len)) + return count; + buf[len] = 0; + if (p[1] == 'x' || p[1] == 'X' || p[0] == 'x' || p[0] == 'X') { + p++; + if (p[0] == 'x' || p[0] == 'X') + p++; + val = simple_strtoul(p, &p, 16); + } else + val = simple_strtoul(p, &p, 10); + if (p == buf) + printk(KERN_INFO DRV_NAME + ": %s is not in hex or decimal form.\n", buf); + else + ieee80211_debug_level = val; + + return strnlen(buf, count); +} + +static int __init ieee80211_init(void) +{ + struct proc_dir_entry *e; + + ieee80211_debug_level = debug; + ieee80211_proc = create_proc_entry(DRV_NAME, S_IFDIR, proc_net); + if (ieee80211_proc == NULL) { + IEEE80211_ERROR("Unable to create " DRV_NAME + " proc directory\n"); + return -EIO; + } + e = create_proc_entry("debug_level", S_IFREG | S_IRUGO | S_IWUSR, + ieee80211_proc); + if (!e) { + remove_proc_entry(DRV_NAME, proc_net); + ieee80211_proc = NULL; + return -EIO; + } + e->read_proc = show_debug_level; + e->write_proc = store_debug_level; + e->data = NULL; + + return 0; +} + +static void __exit ieee80211_exit(void) +{ + if (ieee80211_proc) { + remove_proc_entry("debug_level", ieee80211_proc); + remove_proc_entry(DRV_NAME, proc_net); + ieee80211_proc = NULL; + } +} + +#include <linux/moduleparam.h> +module_param(debug, int, 0444); +MODULE_PARM_DESC(debug, "debug output mask"); + + +module_exit(ieee80211_exit); +module_init(ieee80211_init); +#endif + +EXPORT_SYMBOL(alloc_ieee80211); +EXPORT_SYMBOL(free_ieee80211); diff --git a/net/ieee80211/ieee80211_rx.c b/net/ieee80211/ieee80211_rx.c new file mode 100644 index 000000000000..2bda8a174818 --- /dev/null +++ b/net/ieee80211/ieee80211_rx.c @@ -0,0 +1,1206 @@ +/* + * Original code based Host AP (software wireless LAN access point) driver + * for Intersil Prism2/2.5/3 - hostap.o module, common routines + * + * Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + * <jkmaline@cc.hut.fi> + * Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + * Copyright (c) 2004, Intel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ + +#include <linux/compiler.h> +#include <linux/config.h> +#include <linux/errno.h> +#include <linux/if_arp.h> +#include <linux/in6.h> +#include <linux/in.h> +#include <linux/ip.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/pci.h> +#include <linux/proc_fs.h> +#include <linux/skbuff.h> +#include <linux/slab.h> +#include <linux/tcp.h> +#include <linux/types.h> +#include <linux/version.h> +#include <linux/wireless.h> +#include <linux/etherdevice.h> +#include <asm/uaccess.h> +#include <linux/ctype.h> + +#include <net/ieee80211.h> + +static inline void ieee80211_monitor_rx(struct ieee80211_device *ieee, + struct sk_buff *skb, + struct ieee80211_rx_stats *rx_stats) +{ + struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; + u16 fc = le16_to_cpu(hdr->frame_ctl); + + skb->dev = ieee->dev; + skb->mac.raw = skb->data; + skb_pull(skb, ieee80211_get_hdrlen(fc)); + skb->pkt_type = PACKET_OTHERHOST; + skb->protocol = __constant_htons(ETH_P_80211_RAW); + memset(skb->cb, 0, sizeof(skb->cb)); + netif_rx(skb); +} + + +/* Called only as a tasklet (software IRQ) */ +static struct ieee80211_frag_entry * +ieee80211_frag_cache_find(struct ieee80211_device *ieee, unsigned int seq, + unsigned int frag, u8 *src, u8 *dst) +{ + struct ieee80211_frag_entry *entry; + int i; + + for (i = 0; i < IEEE80211_FRAG_CACHE_LEN; i++) { + entry = &ieee->frag_cache[i]; + if (entry->skb != NULL && + time_after(jiffies, entry->first_frag_time + 2 * HZ)) { + IEEE80211_DEBUG_FRAG( + "expiring fragment cache entry " + "seq=%u last_frag=%u\n", + entry->seq, entry->last_frag); + dev_kfree_skb_any(entry->skb); + entry->skb = NULL; + } + + if (entry->skb != NULL && entry->seq == seq && + (entry->last_frag + 1 == frag || frag == -1) && + memcmp(entry->src_addr, src, ETH_ALEN) == 0 && + memcmp(entry->dst_addr, dst, ETH_ALEN) == 0) + return entry; + } + + return NULL; +} + +/* Called only as a tasklet (software IRQ) */ +static struct sk_buff * +ieee80211_frag_cache_get(struct ieee80211_device *ieee, + struct ieee80211_hdr *hdr) +{ + struct sk_buff *skb = NULL; + u16 sc; + unsigned int frag, seq; + struct ieee80211_frag_entry *entry; + + sc = le16_to_cpu(hdr->seq_ctl); + frag = WLAN_GET_SEQ_FRAG(sc); + seq = WLAN_GET_SEQ_SEQ(sc); + + if (frag == 0) { + /* Reserve enough space to fit maximum frame length */ + skb = dev_alloc_skb(ieee->dev->mtu + + sizeof(struct ieee80211_hdr) + + 8 /* LLC */ + + 2 /* alignment */ + + 8 /* WEP */ + ETH_ALEN /* WDS */); + if (skb == NULL) + return NULL; + + entry = &ieee->frag_cache[ieee->frag_next_idx]; + ieee->frag_next_idx++; + if (ieee->frag_next_idx >= IEEE80211_FRAG_CACHE_LEN) + ieee->frag_next_idx = 0; + + if (entry->skb != NULL) + dev_kfree_skb_any(entry->skb); + + entry->first_frag_time = jiffies; + entry->seq = seq; + entry->last_frag = frag; + entry->skb = skb; + memcpy(entry->src_addr, hdr->addr2, ETH_ALEN); + memcpy(entry->dst_addr, hdr->addr1, ETH_ALEN); + } else { + /* received a fragment of a frame for which the head fragment + * should have already been received */ + entry = ieee80211_frag_cache_find(ieee, seq, frag, hdr->addr2, + hdr->addr1); + if (entry != NULL) { + entry->last_frag = frag; + skb = entry->skb; + } + } + + return skb; +} + + +/* Called only as a tasklet (software IRQ) */ +static int ieee80211_frag_cache_invalidate(struct ieee80211_device *ieee, + struct ieee80211_hdr *hdr) +{ + u16 sc; + unsigned int seq; + struct ieee80211_frag_entry *entry; + + sc = le16_to_cpu(hdr->seq_ctl); + seq = WLAN_GET_SEQ_SEQ(sc); + + entry = ieee80211_frag_cache_find(ieee, seq, -1, hdr->addr2, + hdr->addr1); + + if (entry == NULL) { + IEEE80211_DEBUG_FRAG( + "could not invalidate fragment cache " + "entry (seq=%u)\n", seq); + return -1; + } + + entry->skb = NULL; + return 0; +} + + +#ifdef NOT_YET +/* ieee80211_rx_frame_mgtmt + * + * Responsible for handling management control frames + * + * Called by ieee80211_rx */ +static inline int +ieee80211_rx_frame_mgmt(struct ieee80211_device *ieee, struct sk_buff *skb, + struct ieee80211_rx_stats *rx_stats, u16 type, + u16 stype) +{ + if (ieee->iw_mode == IW_MODE_MASTER) { + printk(KERN_DEBUG "%s: Master mode not yet suppported.\n", + ieee->dev->name); + return 0; +/* + hostap_update_sta_ps(ieee, (struct hostap_ieee80211_hdr *) + skb->data);*/ + } + + if (ieee->hostapd && type == WLAN_FC_TYPE_MGMT) { + if (stype == WLAN_FC_STYPE_BEACON && + ieee->iw_mode == IW_MODE_MASTER) { + struct sk_buff *skb2; + /* Process beacon frames also in kernel driver to + * update STA(AP) table statistics */ + skb2 = skb_clone(skb, GFP_ATOMIC); + if (skb2) + hostap_rx(skb2->dev, skb2, rx_stats); + } + + /* send management frames to the user space daemon for + * processing */ + ieee->apdevstats.rx_packets++; + ieee->apdevstats.rx_bytes += skb->len; + prism2_rx_80211(ieee->apdev, skb, rx_stats, PRISM2_RX_MGMT); + return 0; + } + + if (ieee->iw_mode == IW_MODE_MASTER) { + if (type != WLAN_FC_TYPE_MGMT && type != WLAN_FC_TYPE_CTRL) { + printk(KERN_DEBUG "%s: unknown management frame " + "(type=0x%02x, stype=0x%02x) dropped\n", + skb->dev->name, type, stype); + return -1; + } + + hostap_rx(skb->dev, skb, rx_stats); + return 0; + } + + printk(KERN_DEBUG "%s: hostap_rx_frame_mgmt: management frame " + "received in non-Host AP mode\n", skb->dev->name); + return -1; +} +#endif + + +/* See IEEE 802.1H for LLC/SNAP encapsulation/decapsulation */ +/* Ethernet-II snap header (RFC1042 for most EtherTypes) */ +static unsigned char rfc1042_header[] = +{ 0xaa, 0xaa, 0x03, 0x00, 0x00, 0x00 }; +/* Bridge-Tunnel header (for EtherTypes ETH_P_AARP and ETH_P_IPX) */ +static unsigned char bridge_tunnel_header[] = +{ 0xaa, 0xaa, 0x03, 0x00, 0x00, 0xf8 }; +/* No encapsulation header if EtherType < 0x600 (=length) */ + +/* Called by ieee80211_rx_frame_decrypt */ +static int ieee80211_is_eapol_frame(struct ieee80211_device *ieee, + struct sk_buff *skb) +{ + struct net_device *dev = ieee->dev; + u16 fc, ethertype; + struct ieee80211_hdr *hdr; + u8 *pos; + + if (skb->len < 24) + return 0; + + hdr = (struct ieee80211_hdr *) skb->data; + fc = le16_to_cpu(hdr->frame_ctl); + + /* check that the frame is unicast frame to us */ + if ((fc & (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)) == + IEEE80211_FCTL_TODS && + memcmp(hdr->addr1, dev->dev_addr, ETH_ALEN) == 0 && + memcmp(hdr->addr3, dev->dev_addr, ETH_ALEN) == 0) { + /* ToDS frame with own addr BSSID and DA */ + } else if ((fc & (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)) == + IEEE80211_FCTL_FROMDS && + memcmp(hdr->addr1, dev->dev_addr, ETH_ALEN) == 0) { + /* FromDS frame with own addr as DA */ + } else + return 0; + + if (skb->len < 24 + 8) + return 0; + + /* check for port access entity Ethernet type */ + pos = skb->data + 24; + ethertype = (pos[6] << 8) | pos[7]; + if (ethertype == ETH_P_PAE) + return 1; + + return 0; +} + +/* Called only as a tasklet (software IRQ), by ieee80211_rx */ +static inline int +ieee80211_rx_frame_decrypt(struct ieee80211_device* ieee, struct sk_buff *skb, + struct ieee80211_crypt_data *crypt) +{ + struct ieee80211_hdr *hdr; + int res, hdrlen; + + if (crypt == NULL || crypt->ops->decrypt_mpdu == NULL) + return 0; + + hdr = (struct ieee80211_hdr *) skb->data; + hdrlen = ieee80211_get_hdrlen(le16_to_cpu(hdr->frame_ctl)); + +#ifdef CONFIG_IEEE80211_CRYPT_TKIP + if (ieee->tkip_countermeasures && + strcmp(crypt->ops->name, "TKIP") == 0) { + if (net_ratelimit()) { + printk(KERN_DEBUG "%s: TKIP countermeasures: dropped " + "received packet from " MAC_FMT "\n", + ieee->dev->name, MAC_ARG(hdr->addr2)); + } + return -1; + } +#endif + + atomic_inc(&crypt->refcnt); + res = crypt->ops->decrypt_mpdu(skb, hdrlen, crypt->priv); + atomic_dec(&crypt->refcnt); + if (res < 0) { + IEEE80211_DEBUG_DROP( + "decryption failed (SA=" MAC_FMT + ") res=%d\n", MAC_ARG(hdr->addr2), res); + if (res == -2) + IEEE80211_DEBUG_DROP("Decryption failed ICV " + "mismatch (key %d)\n", + skb->data[hdrlen + 3] >> 6); + ieee->ieee_stats.rx_discards_undecryptable++; + return -1; + } + + return res; +} + + +/* Called only as a tasklet (software IRQ), by ieee80211_rx */ +static inline int +ieee80211_rx_frame_decrypt_msdu(struct ieee80211_device* ieee, struct sk_buff *skb, + int keyidx, struct ieee80211_crypt_data *crypt) +{ + struct ieee80211_hdr *hdr; + int res, hdrlen; + + if (crypt == NULL || crypt->ops->decrypt_msdu == NULL) + return 0; + + hdr = (struct ieee80211_hdr *) skb->data; + hdrlen = ieee80211_get_hdrlen(le16_to_cpu(hdr->frame_ctl)); + + atomic_inc(&crypt->refcnt); + res = crypt->ops->decrypt_msdu(skb, keyidx, hdrlen, crypt->priv); + atomic_dec(&crypt->refcnt); + if (res < 0) { + printk(KERN_DEBUG "%s: MSDU decryption/MIC verification failed" + " (SA=" MAC_FMT " keyidx=%d)\n", + ieee->dev->name, MAC_ARG(hdr->addr2), keyidx); + return -1; + } + + return 0; +} + + +/* All received frames are sent to this function. @skb contains the frame in + * IEEE 802.11 format, i.e., in the format it was sent over air. + * This function is called only as a tasklet (software IRQ). */ +int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, + struct ieee80211_rx_stats *rx_stats) +{ + struct net_device *dev = ieee->dev; + struct ieee80211_hdr *hdr; + size_t hdrlen; + u16 fc, type, stype, sc; + struct net_device_stats *stats; + unsigned int frag; + u8 *payload; + u16 ethertype; +#ifdef NOT_YET + struct net_device *wds = NULL; + struct sk_buff *skb2 = NULL; + struct net_device *wds = NULL; + int frame_authorized = 0; + int from_assoc_ap = 0; + void *sta = NULL; +#endif + u8 dst[ETH_ALEN]; + u8 src[ETH_ALEN]; + struct ieee80211_crypt_data *crypt = NULL; + int keyidx = 0; + + hdr = (struct ieee80211_hdr *)skb->data; + stats = &ieee->stats; + + if (skb->len < 10) { + printk(KERN_INFO "%s: SKB length < 10\n", + dev->name); + goto rx_dropped; + } + + fc = le16_to_cpu(hdr->frame_ctl); + type = WLAN_FC_GET_TYPE(fc); + stype = WLAN_FC_GET_STYPE(fc); + sc = le16_to_cpu(hdr->seq_ctl); + frag = WLAN_GET_SEQ_FRAG(sc); + hdrlen = ieee80211_get_hdrlen(fc); + +#ifdef NOT_YET +#if WIRELESS_EXT > 15 + /* Put this code here so that we avoid duplicating it in all + * Rx paths. - Jean II */ +#ifdef IW_WIRELESS_SPY /* defined in iw_handler.h */ + /* If spy monitoring on */ + if (iface->spy_data.spy_number > 0) { + struct iw_quality wstats; + wstats.level = rx_stats->signal; + wstats.noise = rx_stats->noise; + wstats.updated = 6; /* No qual value */ + /* Update spy records */ + wireless_spy_update(dev, hdr->addr2, &wstats); + } +#endif /* IW_WIRELESS_SPY */ +#endif /* WIRELESS_EXT > 15 */ + hostap_update_rx_stats(local->ap, hdr, rx_stats); +#endif + +#if WIRELESS_EXT > 15 + if (ieee->iw_mode == IW_MODE_MONITOR) { + ieee80211_monitor_rx(ieee, skb, rx_stats); + stats->rx_packets++; + stats->rx_bytes += skb->len; + return 1; + } +#endif + + if (ieee->host_decrypt) { + int idx = 0; + if (skb->len >= hdrlen + 3) + idx = skb->data[hdrlen + 3] >> 6; + crypt = ieee->crypt[idx]; +#ifdef NOT_YET + sta = NULL; + + /* Use station specific key to override default keys if the + * receiver address is a unicast address ("individual RA"). If + * bcrx_sta_key parameter is set, station specific key is used + * even with broad/multicast targets (this is against IEEE + * 802.11, but makes it easier to use different keys with + * stations that do not support WEP key mapping). */ + + if (!(hdr->addr1[0] & 0x01) || local->bcrx_sta_key) + (void) hostap_handle_sta_crypto(local, hdr, &crypt, + &sta); +#endif + + /* allow NULL decrypt to indicate an station specific override + * for default encryption */ + if (crypt && (crypt->ops == NULL || + crypt->ops->decrypt_mpdu == NULL)) + crypt = NULL; + + if (!crypt && (fc & IEEE80211_FCTL_WEP)) { + /* This seems to be triggered by some (multicast?) + * frames from other than current BSS, so just drop the + * frames silently instead of filling system log with + * these reports. */ + IEEE80211_DEBUG_DROP("Decryption failed (not set)" + " (SA=" MAC_FMT ")\n", + MAC_ARG(hdr->addr2)); + ieee->ieee_stats.rx_discards_undecryptable++; + goto rx_dropped; + } + } + +#ifdef NOT_YET + if (type != WLAN_FC_TYPE_DATA) { + if (type == WLAN_FC_TYPE_MGMT && stype == WLAN_FC_STYPE_AUTH && + fc & IEEE80211_FCTL_WEP && ieee->host_decrypt && + (keyidx = hostap_rx_frame_decrypt(ieee, skb, crypt)) < 0) + { + printk(KERN_DEBUG "%s: failed to decrypt mgmt::auth " + "from " MAC_FMT "\n", dev->name, + MAC_ARG(hdr->addr2)); + /* TODO: could inform hostapd about this so that it + * could send auth failure report */ + goto rx_dropped; + } + + if (ieee80211_rx_frame_mgmt(ieee, skb, rx_stats, type, stype)) + goto rx_dropped; + else + goto rx_exit; + } +#endif + + /* Data frame - extract src/dst addresses */ + if (skb->len < IEEE80211_DATA_HDR3_LEN) + goto rx_dropped; + + switch (fc & (IEEE80211_FCTL_FROMDS | IEEE80211_FCTL_TODS)) { + case IEEE80211_FCTL_FROMDS: + memcpy(dst, hdr->addr1, ETH_ALEN); + memcpy(src, hdr->addr3, ETH_ALEN); + break; + case IEEE80211_FCTL_TODS: + memcpy(dst, hdr->addr3, ETH_ALEN); + memcpy(src, hdr->addr2, ETH_ALEN); + break; + case IEEE80211_FCTL_FROMDS | IEEE80211_FCTL_TODS: + if (skb->len < IEEE80211_DATA_HDR4_LEN) + goto rx_dropped; + memcpy(dst, hdr->addr3, ETH_ALEN); + memcpy(src, hdr->addr4, ETH_ALEN); + break; + case 0: + memcpy(dst, hdr->addr1, ETH_ALEN); + memcpy(src, hdr->addr2, ETH_ALEN); + break; + } + +#ifdef NOT_YET + if (hostap_rx_frame_wds(ieee, hdr, fc, &wds)) + goto rx_dropped; + if (wds) { + skb->dev = dev = wds; + stats = hostap_get_stats(dev); + } + + if (ieee->iw_mode == IW_MODE_MASTER && !wds && + (fc & (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)) == IEEE80211_FCTL_FROMDS && + ieee->stadev && + memcmp(hdr->addr2, ieee->assoc_ap_addr, ETH_ALEN) == 0) { + /* Frame from BSSID of the AP for which we are a client */ + skb->dev = dev = ieee->stadev; + stats = hostap_get_stats(dev); + from_assoc_ap = 1; + } +#endif + + dev->last_rx = jiffies; + +#ifdef NOT_YET + if ((ieee->iw_mode == IW_MODE_MASTER || + ieee->iw_mode == IW_MODE_REPEAT) && + !from_assoc_ap) { + switch (hostap_handle_sta_rx(ieee, dev, skb, rx_stats, + wds != NULL)) { + case AP_RX_CONTINUE_NOT_AUTHORIZED: + frame_authorized = 0; + break; + case AP_RX_CONTINUE: + frame_authorized = 1; + break; + case AP_RX_DROP: + goto rx_dropped; + case AP_RX_EXIT: + goto rx_exit; + } + } +#endif + + /* Nullfunc frames may have PS-bit set, so they must be passed to + * hostap_handle_sta_rx() before being dropped here. */ + if (stype != IEEE80211_STYPE_DATA && + stype != IEEE80211_STYPE_DATA_CFACK && + stype != IEEE80211_STYPE_DATA_CFPOLL && + stype != IEEE80211_STYPE_DATA_CFACKPOLL) { + if (stype != IEEE80211_STYPE_NULLFUNC) + IEEE80211_DEBUG_DROP( + "RX: dropped data frame " + "with no data (type=0x%02x, " + "subtype=0x%02x, len=%d)\n", + type, stype, skb->len); + goto rx_dropped; + } + + /* skb: hdr + (possibly fragmented, possibly encrypted) payload */ + + if (ieee->host_decrypt && (fc & IEEE80211_FCTL_WEP) && + (keyidx = ieee80211_rx_frame_decrypt(ieee, skb, crypt)) < 0) + goto rx_dropped; + + hdr = (struct ieee80211_hdr *) skb->data; + + /* skb: hdr + (possibly fragmented) plaintext payload */ + // PR: FIXME: hostap has additional conditions in the "if" below: + // ieee->host_decrypt && (fc & IEEE80211_FCTL_WEP) && + if ((frag != 0 || (fc & IEEE80211_FCTL_MOREFRAGS))) { + int flen; + struct sk_buff *frag_skb = ieee80211_frag_cache_get(ieee, hdr); + IEEE80211_DEBUG_FRAG("Rx Fragment received (%u)\n", frag); + + if (!frag_skb) { + IEEE80211_DEBUG(IEEE80211_DL_RX | IEEE80211_DL_FRAG, + "Rx cannot get skb from fragment " + "cache (morefrag=%d seq=%u frag=%u)\n", + (fc & IEEE80211_FCTL_MOREFRAGS) != 0, + WLAN_GET_SEQ_SEQ(sc), frag); + goto rx_dropped; + } + + flen = skb->len; + if (frag != 0) + flen -= hdrlen; + + if (frag_skb->tail + flen > frag_skb->end) { + printk(KERN_WARNING "%s: host decrypted and " + "reassembled frame did not fit skb\n", + dev->name); + ieee80211_frag_cache_invalidate(ieee, hdr); + goto rx_dropped; + } + + if (frag == 0) { + /* copy first fragment (including full headers) into + * beginning of the fragment cache skb */ + memcpy(skb_put(frag_skb, flen), skb->data, flen); + } else { + /* append frame payload to the end of the fragment + * cache skb */ + memcpy(skb_put(frag_skb, flen), skb->data + hdrlen, + flen); + } + dev_kfree_skb_any(skb); + skb = NULL; + + if (fc & IEEE80211_FCTL_MOREFRAGS) { + /* more fragments expected - leave the skb in fragment + * cache for now; it will be delivered to upper layers + * after all fragments have been received */ + goto rx_exit; + } + + /* this was the last fragment and the frame will be + * delivered, so remove skb from fragment cache */ + skb = frag_skb; + hdr = (struct ieee80211_hdr *) skb->data; + ieee80211_frag_cache_invalidate(ieee, hdr); + } + + /* skb: hdr + (possible reassembled) full MSDU payload; possibly still + * encrypted/authenticated */ + if (ieee->host_decrypt && (fc & IEEE80211_FCTL_WEP) && + ieee80211_rx_frame_decrypt_msdu(ieee, skb, keyidx, crypt)) + goto rx_dropped; + + hdr = (struct ieee80211_hdr *) skb->data; + if (crypt && !(fc & IEEE80211_FCTL_WEP) && !ieee->open_wep) { + if (/*ieee->ieee802_1x &&*/ + ieee80211_is_eapol_frame(ieee, skb)) { +#ifdef CONFIG_IEEE80211_DEBUG + /* pass unencrypted EAPOL frames even if encryption is + * configured */ + struct eapol *eap = (struct eapol *)(skb->data + + 24); + IEEE80211_DEBUG_EAP("RX: IEEE 802.1X EAPOL frame: %s\n", + eap_get_type(eap->type)); +#endif + } else { + IEEE80211_DEBUG_DROP( + "encryption configured, but RX " + "frame not encrypted (SA=" MAC_FMT ")\n", + MAC_ARG(hdr->addr2)); + goto rx_dropped; + } + } + +#ifdef CONFIG_IEEE80211_DEBUG + if (crypt && !(fc & IEEE80211_FCTL_WEP) && + ieee80211_is_eapol_frame(ieee, skb)) { + struct eapol *eap = (struct eapol *)(skb->data + + 24); + IEEE80211_DEBUG_EAP("RX: IEEE 802.1X EAPOL frame: %s\n", + eap_get_type(eap->type)); + } +#endif + + if (crypt && !(fc & IEEE80211_FCTL_WEP) && !ieee->open_wep && + !ieee80211_is_eapol_frame(ieee, skb)) { + IEEE80211_DEBUG_DROP( + "dropped unencrypted RX data " + "frame from " MAC_FMT + " (drop_unencrypted=1)\n", + MAC_ARG(hdr->addr2)); + goto rx_dropped; + } + + /* skb: hdr + (possible reassembled) full plaintext payload */ + + payload = skb->data + hdrlen; + ethertype = (payload[6] << 8) | payload[7]; + +#ifdef NOT_YET + /* If IEEE 802.1X is used, check whether the port is authorized to send + * the received frame. */ + if (ieee->ieee802_1x && ieee->iw_mode == IW_MODE_MASTER) { + if (ethertype == ETH_P_PAE) { + printk(KERN_DEBUG "%s: RX: IEEE 802.1X frame\n", + dev->name); + if (ieee->hostapd && ieee->apdev) { + /* Send IEEE 802.1X frames to the user + * space daemon for processing */ + prism2_rx_80211(ieee->apdev, skb, rx_stats, + PRISM2_RX_MGMT); + ieee->apdevstats.rx_packets++; + ieee->apdevstats.rx_bytes += skb->len; + goto rx_exit; + } + } else if (!frame_authorized) { + printk(KERN_DEBUG "%s: dropped frame from " + "unauthorized port (IEEE 802.1X): " + "ethertype=0x%04x\n", + dev->name, ethertype); + goto rx_dropped; + } + } +#endif + + /* convert hdr + possible LLC headers into Ethernet header */ + if (skb->len - hdrlen >= 8 && + ((memcmp(payload, rfc1042_header, SNAP_SIZE) == 0 && + ethertype != ETH_P_AARP && ethertype != ETH_P_IPX) || + memcmp(payload, bridge_tunnel_header, SNAP_SIZE) == 0)) { + /* remove RFC1042 or Bridge-Tunnel encapsulation and + * replace EtherType */ + skb_pull(skb, hdrlen + SNAP_SIZE); + memcpy(skb_push(skb, ETH_ALEN), src, ETH_ALEN); + memcpy(skb_push(skb, ETH_ALEN), dst, ETH_ALEN); + } else { + u16 len; + /* Leave Ethernet header part of hdr and full payload */ + skb_pull(skb, hdrlen); + len = htons(skb->len); + memcpy(skb_push(skb, 2), &len, 2); + memcpy(skb_push(skb, ETH_ALEN), src, ETH_ALEN); + memcpy(skb_push(skb, ETH_ALEN), dst, ETH_ALEN); + } + +#ifdef NOT_YET + if (wds && ((fc & (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)) == + IEEE80211_FCTL_TODS) && + skb->len >= ETH_HLEN + ETH_ALEN) { + /* Non-standard frame: get addr4 from its bogus location after + * the payload */ + memcpy(skb->data + ETH_ALEN, + skb->data + skb->len - ETH_ALEN, ETH_ALEN); + skb_trim(skb, skb->len - ETH_ALEN); + } +#endif + + stats->rx_packets++; + stats->rx_bytes += skb->len; + +#ifdef NOT_YET + if (ieee->iw_mode == IW_MODE_MASTER && !wds && + ieee->ap->bridge_packets) { + if (dst[0] & 0x01) { + /* copy multicast frame both to the higher layers and + * to the wireless media */ + ieee->ap->bridged_multicast++; + skb2 = skb_clone(skb, GFP_ATOMIC); + if (skb2 == NULL) + printk(KERN_DEBUG "%s: skb_clone failed for " + "multicast frame\n", dev->name); + } else if (hostap_is_sta_assoc(ieee->ap, dst)) { + /* send frame directly to the associated STA using + * wireless media and not passing to higher layers */ + ieee->ap->bridged_unicast++; + skb2 = skb; + skb = NULL; + } + } + + if (skb2 != NULL) { + /* send to wireless media */ + skb2->protocol = __constant_htons(ETH_P_802_3); + skb2->mac.raw = skb2->nh.raw = skb2->data; + /* skb2->nh.raw = skb2->data + ETH_HLEN; */ + skb2->dev = dev; + dev_queue_xmit(skb2); + } + +#endif + + if (skb) { + skb->protocol = eth_type_trans(skb, dev); + memset(skb->cb, 0, sizeof(skb->cb)); + skb->dev = dev; + skb->ip_summed = CHECKSUM_NONE; /* 802.11 crc not sufficient */ + netif_rx(skb); + } + + rx_exit: +#ifdef NOT_YET + if (sta) + hostap_handle_sta_release(sta); +#endif + return 1; + + rx_dropped: + stats->rx_dropped++; + + /* Returning 0 indicates to caller that we have not handled the SKB-- + * so it is still allocated and can be used again by underlying + * hardware as a DMA target */ + return 0; +} + +#define MGMT_FRAME_FIXED_PART_LENGTH 0x24 + +static inline int ieee80211_is_ofdm_rate(u8 rate) +{ + switch (rate & ~IEEE80211_BASIC_RATE_MASK) { + case IEEE80211_OFDM_RATE_6MB: + case IEEE80211_OFDM_RATE_9MB: + case IEEE80211_OFDM_RATE_12MB: + case IEEE80211_OFDM_RATE_18MB: + case IEEE80211_OFDM_RATE_24MB: + case IEEE80211_OFDM_RATE_36MB: + case IEEE80211_OFDM_RATE_48MB: + case IEEE80211_OFDM_RATE_54MB: + return 1; + } + return 0; +} + + +static inline int ieee80211_network_init( + struct ieee80211_device *ieee, + struct ieee80211_probe_response *beacon, + struct ieee80211_network *network, + struct ieee80211_rx_stats *stats) +{ +#ifdef CONFIG_IEEE80211_DEBUG + char rates_str[64]; + char *p; +#endif + struct ieee80211_info_element *info_element; + u16 left; + u8 i; + + /* Pull out fixed field data */ + memcpy(network->bssid, beacon->header.addr3, ETH_ALEN); + network->capability = beacon->capability; + network->last_scanned = jiffies; + network->time_stamp[0] = beacon->time_stamp[0]; + network->time_stamp[1] = beacon->time_stamp[1]; + network->beacon_interval = beacon->beacon_interval; + /* Where to pull this? beacon->listen_interval;*/ + network->listen_interval = 0x0A; + network->rates_len = network->rates_ex_len = 0; + network->last_associate = 0; + network->ssid_len = 0; + network->flags = 0; + network->atim_window = 0; + + if (stats->freq == IEEE80211_52GHZ_BAND) { + /* for A band (No DS info) */ + network->channel = stats->received_channel; + } else + network->flags |= NETWORK_HAS_CCK; + + network->wpa_ie_len = 0; + network->rsn_ie_len = 0; + + info_element = &beacon->info_element; + left = stats->len - ((void *)info_element - (void *)beacon); + while (left >= sizeof(struct ieee80211_info_element_hdr)) { + if (sizeof(struct ieee80211_info_element_hdr) + info_element->len > left) { + IEEE80211_DEBUG_SCAN("SCAN: parse failed: info_element->len + 2 > left : info_element->len+2=%d left=%d.\n", + info_element->len + sizeof(struct ieee80211_info_element), + left); + return 1; + } + + switch (info_element->id) { + case MFIE_TYPE_SSID: + if (ieee80211_is_empty_essid(info_element->data, + info_element->len)) { + network->flags |= NETWORK_EMPTY_ESSID; + break; + } + + network->ssid_len = min(info_element->len, + (u8)IW_ESSID_MAX_SIZE); + memcpy(network->ssid, info_element->data, network->ssid_len); + if (network->ssid_len < IW_ESSID_MAX_SIZE) + memset(network->ssid + network->ssid_len, 0, + IW_ESSID_MAX_SIZE - network->ssid_len); + + IEEE80211_DEBUG_SCAN("MFIE_TYPE_SSID: '%s' len=%d.\n", + network->ssid, network->ssid_len); + break; + + case MFIE_TYPE_RATES: +#ifdef CONFIG_IEEE80211_DEBUG + p = rates_str; +#endif + network->rates_len = min(info_element->len, MAX_RATES_LENGTH); + for (i = 0; i < network->rates_len; i++) { + network->rates[i] = info_element->data[i]; +#ifdef CONFIG_IEEE80211_DEBUG + p += snprintf(p, sizeof(rates_str) - (p - rates_str), "%02X ", network->rates[i]); +#endif + if (ieee80211_is_ofdm_rate(info_element->data[i])) { + network->flags |= NETWORK_HAS_OFDM; + if (info_element->data[i] & + IEEE80211_BASIC_RATE_MASK) + network->flags &= + ~NETWORK_HAS_CCK; + } + } + + IEEE80211_DEBUG_SCAN("MFIE_TYPE_RATES: '%s' (%d)\n", + rates_str, network->rates_len); + break; + + case MFIE_TYPE_RATES_EX: +#ifdef CONFIG_IEEE80211_DEBUG + p = rates_str; +#endif + network->rates_ex_len = min(info_element->len, MAX_RATES_EX_LENGTH); + for (i = 0; i < network->rates_ex_len; i++) { + network->rates_ex[i] = info_element->data[i]; +#ifdef CONFIG_IEEE80211_DEBUG + p += snprintf(p, sizeof(rates_str) - (p - rates_str), "%02X ", network->rates[i]); +#endif + if (ieee80211_is_ofdm_rate(info_element->data[i])) { + network->flags |= NETWORK_HAS_OFDM; + if (info_element->data[i] & + IEEE80211_BASIC_RATE_MASK) + network->flags &= + ~NETWORK_HAS_CCK; + } + } + + IEEE80211_DEBUG_SCAN("MFIE_TYPE_RATES_EX: '%s' (%d)\n", + rates_str, network->rates_ex_len); + break; + + case MFIE_TYPE_DS_SET: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_DS_SET: %d\n", + info_element->data[0]); + if (stats->freq == IEEE80211_24GHZ_BAND) + network->channel = info_element->data[0]; + break; + + case MFIE_TYPE_FH_SET: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_FH_SET: ignored\n"); + break; + + case MFIE_TYPE_CF_SET: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_CF_SET: ignored\n"); + break; + + case MFIE_TYPE_TIM: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_TIM: ignored\n"); + break; + + case MFIE_TYPE_IBSS_SET: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_IBSS_SET: ignored\n"); + break; + + case MFIE_TYPE_CHALLENGE: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_CHALLENGE: ignored\n"); + break; + + case MFIE_TYPE_GENERIC: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_GENERIC: %d bytes\n", + info_element->len); + if (info_element->len >= 4 && + info_element->data[0] == 0x00 && + info_element->data[1] == 0x50 && + info_element->data[2] == 0xf2 && + info_element->data[3] == 0x01) { + network->wpa_ie_len = min(info_element->len + 2, + MAX_WPA_IE_LEN); + memcpy(network->wpa_ie, info_element, + network->wpa_ie_len); + } + break; + + case MFIE_TYPE_RSN: + IEEE80211_DEBUG_SCAN("MFIE_TYPE_RSN: %d bytes\n", + info_element->len); + network->rsn_ie_len = min(info_element->len + 2, + MAX_WPA_IE_LEN); + memcpy(network->rsn_ie, info_element, + network->rsn_ie_len); + break; + + default: + IEEE80211_DEBUG_SCAN("unsupported IE %d\n", + info_element->id); + break; + } + + left -= sizeof(struct ieee80211_info_element_hdr) + + info_element->len; + info_element = (struct ieee80211_info_element *) + &info_element->data[info_element->len]; + } + + network->mode = 0; + if (stats->freq == IEEE80211_52GHZ_BAND) + network->mode = IEEE_A; + else { + if (network->flags & NETWORK_HAS_OFDM) + network->mode |= IEEE_G; + if (network->flags & NETWORK_HAS_CCK) + network->mode |= IEEE_B; + } + + if (network->mode == 0) { + IEEE80211_DEBUG_SCAN("Filtered out '%s (" MAC_FMT ")' " + "network.\n", + escape_essid(network->ssid, + network->ssid_len), + MAC_ARG(network->bssid)); + return 1; + } + + if (ieee80211_is_empty_essid(network->ssid, network->ssid_len)) + network->flags |= NETWORK_EMPTY_ESSID; + + memcpy(&network->stats, stats, sizeof(network->stats)); + + return 0; +} + +static inline int is_same_network(struct ieee80211_network *src, + struct ieee80211_network *dst) +{ + /* A network is only a duplicate if the channel, BSSID, and ESSID + * all match. We treat all <hidden> with the same BSSID and channel + * as one network */ + return ((src->ssid_len == dst->ssid_len) && + (src->channel == dst->channel) && + !memcmp(src->bssid, dst->bssid, ETH_ALEN) && + !memcmp(src->ssid, dst->ssid, src->ssid_len)); +} + +static inline void update_network(struct ieee80211_network *dst, + struct ieee80211_network *src) +{ + memcpy(&dst->stats, &src->stats, sizeof(struct ieee80211_rx_stats)); + dst->capability = src->capability; + memcpy(dst->rates, src->rates, src->rates_len); + dst->rates_len = src->rates_len; + memcpy(dst->rates_ex, src->rates_ex, src->rates_ex_len); + dst->rates_ex_len = src->rates_ex_len; + + dst->mode = src->mode; + dst->flags = src->flags; + dst->time_stamp[0] = src->time_stamp[0]; + dst->time_stamp[1] = src->time_stamp[1]; + + dst->beacon_interval = src->beacon_interval; + dst->listen_interval = src->listen_interval; + dst->atim_window = src->atim_window; + + memcpy(dst->wpa_ie, src->wpa_ie, src->wpa_ie_len); + dst->wpa_ie_len = src->wpa_ie_len; + memcpy(dst->rsn_ie, src->rsn_ie, src->rsn_ie_len); + dst->rsn_ie_len = src->rsn_ie_len; + + dst->last_scanned = jiffies; + /* dst->last_associate is not overwritten */ +} + +static inline void ieee80211_process_probe_response( + struct ieee80211_device *ieee, + struct ieee80211_probe_response *beacon, + struct ieee80211_rx_stats *stats) +{ + struct ieee80211_network network; + struct ieee80211_network *target; + struct ieee80211_network *oldest = NULL; +#ifdef CONFIG_IEEE80211_DEBUG + struct ieee80211_info_element *info_element = &beacon->info_element; +#endif + unsigned long flags; + + IEEE80211_DEBUG_SCAN( + "'%s' (" MAC_FMT "): %c%c%c%c %c%c%c%c-%c%c%c%c %c%c%c%c\n", + escape_essid(info_element->data, info_element->len), + MAC_ARG(beacon->header.addr3), + (beacon->capability & (1<<0xf)) ? '1' : '0', + (beacon->capability & (1<<0xe)) ? '1' : '0', + (beacon->capability & (1<<0xd)) ? '1' : '0', + (beacon->capability & (1<<0xc)) ? '1' : '0', + (beacon->capability & (1<<0xb)) ? '1' : '0', + (beacon->capability & (1<<0xa)) ? '1' : '0', + (beacon->capability & (1<<0x9)) ? '1' : '0', + (beacon->capability & (1<<0x8)) ? '1' : '0', + (beacon->capability & (1<<0x7)) ? '1' : '0', + (beacon->capability & (1<<0x6)) ? '1' : '0', + (beacon->capability & (1<<0x5)) ? '1' : '0', + (beacon->capability & (1<<0x4)) ? '1' : '0', + (beacon->capability & (1<<0x3)) ? '1' : '0', + (beacon->capability & (1<<0x2)) ? '1' : '0', + (beacon->capability & (1<<0x1)) ? '1' : '0', + (beacon->capability & (1<<0x0)) ? '1' : '0'); + + if (ieee80211_network_init(ieee, beacon, &network, stats)) { + IEEE80211_DEBUG_SCAN("Dropped '%s' (" MAC_FMT ") via %s.\n", + escape_essid(info_element->data, + info_element->len), + MAC_ARG(beacon->header.addr3), + WLAN_FC_GET_STYPE(beacon->header.frame_ctl) == + IEEE80211_STYPE_PROBE_RESP ? + "PROBE RESPONSE" : "BEACON"); + return; + } + + /* The network parsed correctly -- so now we scan our known networks + * to see if we can find it in our list. + * + * NOTE: This search is definitely not optimized. Once its doing + * the "right thing" we'll optimize it for efficiency if + * necessary */ + + /* Search for this entry in the list and update it if it is + * already there. */ + + spin_lock_irqsave(&ieee->lock, flags); + + list_for_each_entry(target, &ieee->network_list, list) { + if (is_same_network(target, &network)) + break; + + if ((oldest == NULL) || + (target->last_scanned < oldest->last_scanned)) + oldest = target; + } + + /* If we didn't find a match, then get a new network slot to initialize + * with this beacon's information */ + if (&target->list == &ieee->network_list) { + if (list_empty(&ieee->network_free_list)) { + /* If there are no more slots, expire the oldest */ + list_del(&oldest->list); + target = oldest; + IEEE80211_DEBUG_SCAN("Expired '%s' (" MAC_FMT ") from " + "network list.\n", + escape_essid(target->ssid, + target->ssid_len), + MAC_ARG(target->bssid)); + } else { + /* Otherwise just pull from the free list */ + target = list_entry(ieee->network_free_list.next, + struct ieee80211_network, list); + list_del(ieee->network_free_list.next); + } + + +#ifdef CONFIG_IEEE80211_DEBUG + IEEE80211_DEBUG_SCAN("Adding '%s' (" MAC_FMT ") via %s.\n", + escape_essid(network.ssid, + network.ssid_len), + MAC_ARG(network.bssid), + WLAN_FC_GET_STYPE(beacon->header.frame_ctl) == + IEEE80211_STYPE_PROBE_RESP ? + "PROBE RESPONSE" : "BEACON"); +#endif + memcpy(target, &network, sizeof(*target)); + list_add_tail(&target->list, &ieee->network_list); + } else { + IEEE80211_DEBUG_SCAN("Updating '%s' (" MAC_FMT ") via %s.\n", + escape_essid(target->ssid, + target->ssid_len), + MAC_ARG(target->bssid), + WLAN_FC_GET_STYPE(beacon->header.frame_ctl) == + IEEE80211_STYPE_PROBE_RESP ? + "PROBE RESPONSE" : "BEACON"); + update_network(target, &network); + } + + spin_unlock_irqrestore(&ieee->lock, flags); +} + +void ieee80211_rx_mgt(struct ieee80211_device *ieee, + struct ieee80211_hdr *header, + struct ieee80211_rx_stats *stats) +{ + switch (WLAN_FC_GET_STYPE(header->frame_ctl)) { + case IEEE80211_STYPE_ASSOC_RESP: + IEEE80211_DEBUG_MGMT("received ASSOCIATION RESPONSE (%d)\n", + WLAN_FC_GET_STYPE(header->frame_ctl)); + break; + + case IEEE80211_STYPE_REASSOC_RESP: + IEEE80211_DEBUG_MGMT("received REASSOCIATION RESPONSE (%d)\n", + WLAN_FC_GET_STYPE(header->frame_ctl)); + break; + + case IEEE80211_STYPE_PROBE_RESP: + IEEE80211_DEBUG_MGMT("received PROBE RESPONSE (%d)\n", + WLAN_FC_GET_STYPE(header->frame_ctl)); + IEEE80211_DEBUG_SCAN("Probe response\n"); + ieee80211_process_probe_response( + ieee, (struct ieee80211_probe_response *)header, stats); + break; + + case IEEE80211_STYPE_BEACON: + IEEE80211_DEBUG_MGMT("received BEACON (%d)\n", + WLAN_FC_GET_STYPE(header->frame_ctl)); + IEEE80211_DEBUG_SCAN("Beacon\n"); + ieee80211_process_probe_response( + ieee, (struct ieee80211_probe_response *)header, stats); + break; + + default: + IEEE80211_DEBUG_MGMT("received UNKNOWN (%d)\n", + WLAN_FC_GET_STYPE(header->frame_ctl)); + IEEE80211_WARNING("%s: Unknown management packet: %d\n", + ieee->dev->name, + WLAN_FC_GET_STYPE(header->frame_ctl)); + break; + } +} + + +EXPORT_SYMBOL(ieee80211_rx_mgt); +EXPORT_SYMBOL(ieee80211_rx); diff --git a/net/ieee80211/ieee80211_tx.c b/net/ieee80211/ieee80211_tx.c new file mode 100644 index 000000000000..308fcd9ab1e3 --- /dev/null +++ b/net/ieee80211/ieee80211_tx.c @@ -0,0 +1,448 @@ +/****************************************************************************** + + Copyright(c) 2003 - 2004 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +******************************************************************************/ +#include <linux/compiler.h> +#include <linux/config.h> +#include <linux/errno.h> +#include <linux/if_arp.h> +#include <linux/in6.h> +#include <linux/in.h> +#include <linux/ip.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/pci.h> +#include <linux/proc_fs.h> +#include <linux/skbuff.h> +#include <linux/slab.h> +#include <linux/tcp.h> +#include <linux/types.h> +#include <linux/version.h> +#include <linux/wireless.h> +#include <linux/etherdevice.h> +#include <asm/uaccess.h> + +#include <net/ieee80211.h> + + +/* + + +802.11 Data Frame + + ,-------------------------------------------------------------------. +Bytes | 2 | 2 | 6 | 6 | 6 | 2 | 0..2312 | 4 | + |------|------|---------|---------|---------|------|---------|------| +Desc. | ctrl | dura | DA/RA | TA | SA | Sequ | Frame | fcs | + | | tion | (BSSID) | | | ence | data | | + `--------------------------------------------------| |------' +Total: 28 non-data bytes `----.----' + | + .- 'Frame data' expands to <---------------------------' + | + V + ,---------------------------------------------------. +Bytes | 1 | 1 | 1 | 3 | 2 | 0-2304 | + |------|------|---------|----------|------|---------| +Desc. | SNAP | SNAP | Control |Eth Tunnel| Type | IP | + | DSAP | SSAP | | | | Packet | + | 0xAA | 0xAA |0x03 (UI)|0x00-00-F8| | | + `-----------------------------------------| | +Total: 8 non-data bytes `----.----' + | + .- 'IP Packet' expands, if WEP enabled, to <--' + | + V + ,-----------------------. +Bytes | 4 | 0-2296 | 4 | + |-----|-----------|-----| +Desc. | IV | Encrypted | ICV | + | | IP Packet | | + `-----------------------' +Total: 8 non-data bytes + + +802.3 Ethernet Data Frame + + ,-----------------------------------------. +Bytes | 6 | 6 | 2 | Variable | 4 | + |-------|-------|------|-----------|------| +Desc. | Dest. | Source| Type | IP Packet | fcs | + | MAC | MAC | | | | + `-----------------------------------------' +Total: 18 non-data bytes + +In the event that fragmentation is required, the incoming payload is split into +N parts of size ieee->fts. The first fragment contains the SNAP header and the +remaining packets are just data. + +If encryption is enabled, each fragment payload size is reduced by enough space +to add the prefix and postfix (IV and ICV totalling 8 bytes in the case of WEP) +So if you have 1500 bytes of payload with ieee->fts set to 500 without +encryption it will take 3 frames. With WEP it will take 4 frames as the +payload of each frame is reduced to 492 bytes. + +* SKB visualization +* +* ,- skb->data +* | +* | ETHERNET HEADER ,-<-- PAYLOAD +* | | 14 bytes from skb->data +* | 2 bytes for Type --> ,T. | (sizeof ethhdr) +* | | | | +* |,-Dest.--. ,--Src.---. | | | +* | 6 bytes| | 6 bytes | | | | +* v | | | | | | +* 0 | v 1 | v | v 2 +* 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +* ^ | ^ | ^ | +* | | | | | | +* | | | | `T' <---- 2 bytes for Type +* | | | | +* | | '---SNAP--' <-------- 6 bytes for SNAP +* | | +* `-IV--' <-------------------- 4 bytes for IV (WEP) +* +* SNAP HEADER +* +*/ + +static u8 P802_1H_OUI[P80211_OUI_LEN] = { 0x00, 0x00, 0xf8 }; +static u8 RFC1042_OUI[P80211_OUI_LEN] = { 0x00, 0x00, 0x00 }; + +static inline int ieee80211_put_snap(u8 *data, u16 h_proto) +{ + struct ieee80211_snap_hdr *snap; + u8 *oui; + + snap = (struct ieee80211_snap_hdr *)data; + snap->dsap = 0xaa; + snap->ssap = 0xaa; + snap->ctrl = 0x03; + + if (h_proto == 0x8137 || h_proto == 0x80f3) + oui = P802_1H_OUI; + else + oui = RFC1042_OUI; + snap->oui[0] = oui[0]; + snap->oui[1] = oui[1]; + snap->oui[2] = oui[2]; + + *(u16 *)(data + SNAP_SIZE) = htons(h_proto); + + return SNAP_SIZE + sizeof(u16); +} + +static inline int ieee80211_encrypt_fragment( + struct ieee80211_device *ieee, + struct sk_buff *frag, + int hdr_len) +{ + struct ieee80211_crypt_data* crypt = ieee->crypt[ieee->tx_keyidx]; + int res; + +#ifdef CONFIG_IEEE80211_CRYPT_TKIP + struct ieee80211_hdr *header; + + if (ieee->tkip_countermeasures && + crypt && crypt->ops && strcmp(crypt->ops->name, "TKIP") == 0) { + header = (struct ieee80211_hdr *) frag->data; + if (net_ratelimit()) { + printk(KERN_DEBUG "%s: TKIP countermeasures: dropped " + "TX packet to " MAC_FMT "\n", + ieee->dev->name, MAC_ARG(header->addr1)); + } + return -1; + } +#endif + /* To encrypt, frame format is: + * IV (4 bytes), clear payload (including SNAP), ICV (4 bytes) */ + + // PR: FIXME: Copied from hostap. Check fragmentation/MSDU/MPDU encryption. + /* Host-based IEEE 802.11 fragmentation for TX is not yet supported, so + * call both MSDU and MPDU encryption functions from here. */ + atomic_inc(&crypt->refcnt); + res = 0; + if (crypt->ops->encrypt_msdu) + res = crypt->ops->encrypt_msdu(frag, hdr_len, crypt->priv); + if (res == 0 && crypt->ops->encrypt_mpdu) + res = crypt->ops->encrypt_mpdu(frag, hdr_len, crypt->priv); + + atomic_dec(&crypt->refcnt); + if (res < 0) { + printk(KERN_INFO "%s: Encryption failed: len=%d.\n", + ieee->dev->name, frag->len); + ieee->ieee_stats.tx_discards++; + return -1; + } + + return 0; +} + + +void ieee80211_txb_free(struct ieee80211_txb *txb) { + int i; + if (unlikely(!txb)) + return; + for (i = 0; i < txb->nr_frags; i++) + if (txb->fragments[i]) + dev_kfree_skb_any(txb->fragments[i]); + kfree(txb); +} + +struct ieee80211_txb *ieee80211_alloc_txb(int nr_frags, int txb_size, + int gfp_mask) +{ + struct ieee80211_txb *txb; + int i; + txb = kmalloc( + sizeof(struct ieee80211_txb) + (sizeof(u8*) * nr_frags), + gfp_mask); + if (!txb) + return NULL; + + memset(txb, 0, sizeof(struct ieee80211_txb)); + txb->nr_frags = nr_frags; + txb->frag_size = txb_size; + + for (i = 0; i < nr_frags; i++) { + txb->fragments[i] = dev_alloc_skb(txb_size); + if (unlikely(!txb->fragments[i])) { + i--; + break; + } + } + if (unlikely(i != nr_frags)) { + while (i >= 0) + dev_kfree_skb_any(txb->fragments[i--]); + kfree(txb); + return NULL; + } + return txb; +} + +/* SKBs are added to the ieee->tx_queue. */ +int ieee80211_xmit(struct sk_buff *skb, + struct net_device *dev) +{ + struct ieee80211_device *ieee = netdev_priv(dev); + struct ieee80211_txb *txb = NULL; + struct ieee80211_hdr *frag_hdr; + int i, bytes_per_frag, nr_frags, bytes_last_frag, frag_size; + unsigned long flags; + struct net_device_stats *stats = &ieee->stats; + int ether_type, encrypt; + int bytes, fc, hdr_len; + struct sk_buff *skb_frag; + struct ieee80211_hdr header = { /* Ensure zero initialized */ + .duration_id = 0, + .seq_ctl = 0 + }; + u8 dest[ETH_ALEN], src[ETH_ALEN]; + + struct ieee80211_crypt_data* crypt; + + spin_lock_irqsave(&ieee->lock, flags); + + /* If there is no driver handler to take the TXB, dont' bother + * creating it... */ + if (!ieee->hard_start_xmit) { + printk(KERN_WARNING "%s: No xmit handler.\n", + ieee->dev->name); + goto success; + } + + if (unlikely(skb->len < SNAP_SIZE + sizeof(u16))) { + printk(KERN_WARNING "%s: skb too small (%d).\n", + ieee->dev->name, skb->len); + goto success; + } + + ether_type = ntohs(((struct ethhdr *)skb->data)->h_proto); + + crypt = ieee->crypt[ieee->tx_keyidx]; + + encrypt = !(ether_type == ETH_P_PAE && ieee->ieee802_1x) && + ieee->host_encrypt && crypt && crypt->ops; + + if (!encrypt && ieee->ieee802_1x && + ieee->drop_unencrypted && ether_type != ETH_P_PAE) { + stats->tx_dropped++; + goto success; + } + +#ifdef CONFIG_IEEE80211_DEBUG + if (crypt && !encrypt && ether_type == ETH_P_PAE) { + struct eapol *eap = (struct eapol *)(skb->data + + sizeof(struct ethhdr) - SNAP_SIZE - sizeof(u16)); + IEEE80211_DEBUG_EAP("TX: IEEE 802.11 EAPOL frame: %s\n", + eap_get_type(eap->type)); + } +#endif + + /* Save source and destination addresses */ + memcpy(&dest, skb->data, ETH_ALEN); + memcpy(&src, skb->data+ETH_ALEN, ETH_ALEN); + + /* Advance the SKB to the start of the payload */ + skb_pull(skb, sizeof(struct ethhdr)); + + /* Determine total amount of storage required for TXB packets */ + bytes = skb->len + SNAP_SIZE + sizeof(u16); + + if (encrypt) + fc = IEEE80211_FTYPE_DATA | IEEE80211_STYPE_DATA | + IEEE80211_FCTL_WEP; + else + fc = IEEE80211_FTYPE_DATA | IEEE80211_STYPE_DATA; + + if (ieee->iw_mode == IW_MODE_INFRA) { + fc |= IEEE80211_FCTL_TODS; + /* To DS: Addr1 = BSSID, Addr2 = SA, + Addr3 = DA */ + memcpy(&header.addr1, ieee->bssid, ETH_ALEN); + memcpy(&header.addr2, &src, ETH_ALEN); + memcpy(&header.addr3, &dest, ETH_ALEN); + } else if (ieee->iw_mode == IW_MODE_ADHOC) { + /* not From/To DS: Addr1 = DA, Addr2 = SA, + Addr3 = BSSID */ + memcpy(&header.addr1, dest, ETH_ALEN); + memcpy(&header.addr2, src, ETH_ALEN); + memcpy(&header.addr3, ieee->bssid, ETH_ALEN); + } + header.frame_ctl = cpu_to_le16(fc); + hdr_len = IEEE80211_3ADDR_LEN; + + /* Determine fragmentation size based on destination (multicast + * and broadcast are not fragmented) */ + if (is_multicast_ether_addr(dest) || + is_broadcast_ether_addr(dest)) + frag_size = MAX_FRAG_THRESHOLD; + else + frag_size = ieee->fts; + + /* Determine amount of payload per fragment. Regardless of if + * this stack is providing the full 802.11 header, one will + * eventually be affixed to this fragment -- so we must account for + * it when determining the amount of payload space. */ + bytes_per_frag = frag_size - IEEE80211_3ADDR_LEN; + if (ieee->config & + (CFG_IEEE80211_COMPUTE_FCS | CFG_IEEE80211_RESERVE_FCS)) + bytes_per_frag -= IEEE80211_FCS_LEN; + + /* Each fragment may need to have room for encryptiong pre/postfix */ + if (encrypt) + bytes_per_frag -= crypt->ops->extra_prefix_len + + crypt->ops->extra_postfix_len; + + /* Number of fragments is the total bytes_per_frag / + * payload_per_fragment */ + nr_frags = bytes / bytes_per_frag; + bytes_last_frag = bytes % bytes_per_frag; + if (bytes_last_frag) + nr_frags++; + else + bytes_last_frag = bytes_per_frag; + + /* When we allocate the TXB we allocate enough space for the reserve + * and full fragment bytes (bytes_per_frag doesn't include prefix, + * postfix, header, FCS, etc.) */ + txb = ieee80211_alloc_txb(nr_frags, frag_size, GFP_ATOMIC); + if (unlikely(!txb)) { + printk(KERN_WARNING "%s: Could not allocate TXB\n", + ieee->dev->name); + goto failed; + } + txb->encrypted = encrypt; + txb->payload_size = bytes; + + for (i = 0; i < nr_frags; i++) { + skb_frag = txb->fragments[i]; + + if (encrypt) + skb_reserve(skb_frag, crypt->ops->extra_prefix_len); + + frag_hdr = (struct ieee80211_hdr *)skb_put(skb_frag, hdr_len); + memcpy(frag_hdr, &header, hdr_len); + + /* If this is not the last fragment, then add the MOREFRAGS + * bit to the frame control */ + if (i != nr_frags - 1) { + frag_hdr->frame_ctl = cpu_to_le16( + fc | IEEE80211_FCTL_MOREFRAGS); + bytes = bytes_per_frag; + } else { + /* The last fragment takes the remaining length */ + bytes = bytes_last_frag; + } + + /* Put a SNAP header on the first fragment */ + if (i == 0) { + ieee80211_put_snap( + skb_put(skb_frag, SNAP_SIZE + sizeof(u16)), + ether_type); + bytes -= SNAP_SIZE + sizeof(u16); + } + + memcpy(skb_put(skb_frag, bytes), skb->data, bytes); + + /* Advance the SKB... */ + skb_pull(skb, bytes); + + /* Encryption routine will move the header forward in order + * to insert the IV between the header and the payload */ + if (encrypt) + ieee80211_encrypt_fragment(ieee, skb_frag, hdr_len); + if (ieee->config & + (CFG_IEEE80211_COMPUTE_FCS | CFG_IEEE80211_RESERVE_FCS)) + skb_put(skb_frag, 4); + } + + + success: + spin_unlock_irqrestore(&ieee->lock, flags); + + dev_kfree_skb_any(skb); + + if (txb) { + if ((*ieee->hard_start_xmit)(txb, dev) == 0) { + stats->tx_packets++; + stats->tx_bytes += txb->payload_size; + return 0; + } + ieee80211_txb_free(txb); + } + + return 0; + + failed: + spin_unlock_irqrestore(&ieee->lock, flags); + netif_stop_queue(dev); + stats->tx_errors++; + return 1; + +} + +EXPORT_SYMBOL(ieee80211_txb_free); diff --git a/net/ieee80211/ieee80211_wx.c b/net/ieee80211/ieee80211_wx.c new file mode 100644 index 000000000000..25a868c2e2f7 --- /dev/null +++ b/net/ieee80211/ieee80211_wx.c @@ -0,0 +1,471 @@ +/****************************************************************************** + + Copyright(c) 2004 Intel Corporation. All rights reserved. + + Portions of this file are based on the WEP enablement code provided by the + Host AP project hostap-drivers v0.1.3 + Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + <jkmaline@cc.hut.fi> + Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> + + This program is free software; you can redistribute it and/or modify it + under the terms of version 2 of the GNU General Public License as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + James P. Ketrenos <ipw2100-admin@linux.intel.com> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +******************************************************************************/ +#include <linux/wireless.h> +#include <linux/version.h> +#include <linux/kmod.h> +#include <linux/module.h> + +#include <net/ieee80211.h> +static const char *ieee80211_modes[] = { + "?", "a", "b", "ab", "g", "ag", "bg", "abg" +}; + +#define MAX_CUSTOM_LEN 64 +static inline char *ipw2100_translate_scan(struct ieee80211_device *ieee, + char *start, char *stop, + struct ieee80211_network *network) +{ + char custom[MAX_CUSTOM_LEN]; + char *p; + struct iw_event iwe; + int i, j; + u8 max_rate, rate; + + /* First entry *MUST* be the AP MAC address */ + iwe.cmd = SIOCGIWAP; + iwe.u.ap_addr.sa_family = ARPHRD_ETHER; + memcpy(iwe.u.ap_addr.sa_data, network->bssid, ETH_ALEN); + start = iwe_stream_add_event(start, stop, &iwe, IW_EV_ADDR_LEN); + + /* Remaining entries will be displayed in the order we provide them */ + + /* Add the ESSID */ + iwe.cmd = SIOCGIWESSID; + iwe.u.data.flags = 1; + if (network->flags & NETWORK_EMPTY_ESSID) { + iwe.u.data.length = sizeof("<hidden>"); + start = iwe_stream_add_point(start, stop, &iwe, "<hidden>"); + } else { + iwe.u.data.length = min(network->ssid_len, (u8)32); + start = iwe_stream_add_point(start, stop, &iwe, network->ssid); + } + + /* Add the protocol name */ + iwe.cmd = SIOCGIWNAME; + snprintf(iwe.u.name, IFNAMSIZ, "IEEE 802.11%s", ieee80211_modes[network->mode]); + start = iwe_stream_add_event(start, stop, &iwe, IW_EV_CHAR_LEN); + + /* Add mode */ + iwe.cmd = SIOCGIWMODE; + if (network->capability & + (WLAN_CAPABILITY_BSS | WLAN_CAPABILITY_IBSS)) { + if (network->capability & WLAN_CAPABILITY_BSS) + iwe.u.mode = IW_MODE_MASTER; + else + iwe.u.mode = IW_MODE_ADHOC; + + start = iwe_stream_add_event(start, stop, &iwe, + IW_EV_UINT_LEN); + } + + /* Add frequency/channel */ + iwe.cmd = SIOCGIWFREQ; +/* iwe.u.freq.m = ieee80211_frequency(network->channel, network->mode); + iwe.u.freq.e = 3; */ + iwe.u.freq.m = network->channel; + iwe.u.freq.e = 0; + iwe.u.freq.i = 0; + start = iwe_stream_add_event(start, stop, &iwe, IW_EV_FREQ_LEN); + + /* Add encryption capability */ + iwe.cmd = SIOCGIWENCODE; + if (network->capability & WLAN_CAPABILITY_PRIVACY) + iwe.u.data.flags = IW_ENCODE_ENABLED | IW_ENCODE_NOKEY; + else + iwe.u.data.flags = IW_ENCODE_DISABLED; + iwe.u.data.length = 0; + start = iwe_stream_add_point(start, stop, &iwe, network->ssid); + + /* Add basic and extended rates */ + max_rate = 0; + p = custom; + p += snprintf(p, MAX_CUSTOM_LEN - (p - custom), " Rates (Mb/s): "); + for (i = 0, j = 0; i < network->rates_len; ) { + if (j < network->rates_ex_len && + ((network->rates_ex[j] & 0x7F) < + (network->rates[i] & 0x7F))) + rate = network->rates_ex[j++] & 0x7F; + else + rate = network->rates[i++] & 0x7F; + if (rate > max_rate) + max_rate = rate; + p += snprintf(p, MAX_CUSTOM_LEN - (p - custom), + "%d%s ", rate >> 1, (rate & 1) ? ".5" : ""); + } + for (; j < network->rates_ex_len; j++) { + rate = network->rates_ex[j] & 0x7F; + p += snprintf(p, MAX_CUSTOM_LEN - (p - custom), + "%d%s ", rate >> 1, (rate & 1) ? ".5" : ""); + if (rate > max_rate) + max_rate = rate; + } + + iwe.cmd = SIOCGIWRATE; + iwe.u.bitrate.fixed = iwe.u.bitrate.disabled = 0; + iwe.u.bitrate.value = max_rate * 500000; + start = iwe_stream_add_event(start, stop, &iwe, + IW_EV_PARAM_LEN); + + iwe.cmd = IWEVCUSTOM; + iwe.u.data.length = p - custom; + if (iwe.u.data.length) + start = iwe_stream_add_point(start, stop, &iwe, custom); + + /* Add quality statistics */ + /* TODO: Fix these values... */ + iwe.cmd = IWEVQUAL; + iwe.u.qual.qual = network->stats.signal; + iwe.u.qual.level = network->stats.rssi; + iwe.u.qual.noise = network->stats.noise; + iwe.u.qual.updated = network->stats.mask & IEEE80211_STATMASK_WEMASK; + if (!(network->stats.mask & IEEE80211_STATMASK_RSSI)) + iwe.u.qual.updated |= IW_QUAL_LEVEL_INVALID; + if (!(network->stats.mask & IEEE80211_STATMASK_NOISE)) + iwe.u.qual.updated |= IW_QUAL_NOISE_INVALID; + if (!(network->stats.mask & IEEE80211_STATMASK_SIGNAL)) + iwe.u.qual.updated |= IW_QUAL_QUAL_INVALID; + + start = iwe_stream_add_event(start, stop, &iwe, IW_EV_QUAL_LEN); + + iwe.cmd = IWEVCUSTOM; + p = custom; + + iwe.u.data.length = p - custom; + if (iwe.u.data.length) + start = iwe_stream_add_point(start, stop, &iwe, custom); + + if (ieee->wpa_enabled && network->wpa_ie_len){ + char buf[MAX_WPA_IE_LEN * 2 + 30]; + + u8 *p = buf; + p += sprintf(p, "wpa_ie="); + for (i = 0; i < network->wpa_ie_len; i++) { + p += sprintf(p, "%02x", network->wpa_ie[i]); + } + + memset(&iwe, 0, sizeof(iwe)); + iwe.cmd = IWEVCUSTOM; + iwe.u.data.length = strlen(buf); + start = iwe_stream_add_point(start, stop, &iwe, buf); + } + + if (ieee->wpa_enabled && network->rsn_ie_len){ + char buf[MAX_WPA_IE_LEN * 2 + 30]; + + u8 *p = buf; + p += sprintf(p, "rsn_ie="); + for (i = 0; i < network->rsn_ie_len; i++) { + p += sprintf(p, "%02x", network->rsn_ie[i]); + } + + memset(&iwe, 0, sizeof(iwe)); + iwe.cmd = IWEVCUSTOM; + iwe.u.data.length = strlen(buf); + start = iwe_stream_add_point(start, stop, &iwe, buf); + } + + /* Add EXTRA: Age to display seconds since last beacon/probe response + * for given network. */ + iwe.cmd = IWEVCUSTOM; + p = custom; + p += snprintf(p, MAX_CUSTOM_LEN - (p - custom), + " Last beacon: %lums ago", (jiffies - network->last_scanned) / (HZ / 100)); + iwe.u.data.length = p - custom; + if (iwe.u.data.length) + start = iwe_stream_add_point(start, stop, &iwe, custom); + + + return start; +} + +int ieee80211_wx_get_scan(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra) +{ + struct ieee80211_network *network; + unsigned long flags; + + char *ev = extra; + char *stop = ev + IW_SCAN_MAX_DATA; + int i = 0; + + IEEE80211_DEBUG_WX("Getting scan\n"); + + spin_lock_irqsave(&ieee->lock, flags); + + list_for_each_entry(network, &ieee->network_list, list) { + i++; + if (ieee->scan_age == 0 || + time_after(network->last_scanned + ieee->scan_age, jiffies)) + ev = ipw2100_translate_scan(ieee, ev, stop, network); + else + IEEE80211_DEBUG_SCAN( + "Not showing network '%s (" + MAC_FMT ")' due to age (%lums).\n", + escape_essid(network->ssid, + network->ssid_len), + MAC_ARG(network->bssid), + (jiffies - network->last_scanned) / (HZ / 100)); + } + + spin_unlock_irqrestore(&ieee->lock, flags); + + wrqu->data.length = ev - extra; + wrqu->data.flags = 0; + + IEEE80211_DEBUG_WX("exit: %d networks returned.\n", i); + + return 0; +} + +int ieee80211_wx_set_encode(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *keybuf) +{ + struct iw_point *erq = &(wrqu->encoding); + struct net_device *dev = ieee->dev; + struct ieee80211_security sec = { + .flags = 0 + }; + int i, key, key_provided, len; + struct ieee80211_crypt_data **crypt; + + IEEE80211_DEBUG_WX("SET_ENCODE\n"); + + key = erq->flags & IW_ENCODE_INDEX; + if (key) { + if (key > WEP_KEYS) + return -EINVAL; + key--; + key_provided = 1; + } else { + key_provided = 0; + key = ieee->tx_keyidx; + } + + IEEE80211_DEBUG_WX("Key: %d [%s]\n", key, key_provided ? + "provided" : "default"); + + crypt = &ieee->crypt[key]; + + if (erq->flags & IW_ENCODE_DISABLED) { + if (key_provided && *crypt) { + IEEE80211_DEBUG_WX("Disabling encryption on key %d.\n", + key); + ieee80211_crypt_delayed_deinit(ieee, crypt); + } else + IEEE80211_DEBUG_WX("Disabling encryption.\n"); + + /* Check all the keys to see if any are still configured, + * and if no key index was provided, de-init them all */ + for (i = 0; i < WEP_KEYS; i++) { + if (ieee->crypt[i] != NULL) { + if (key_provided) + break; + ieee80211_crypt_delayed_deinit( + ieee, &ieee->crypt[i]); + } + } + + if (i == WEP_KEYS) { + sec.enabled = 0; + sec.level = SEC_LEVEL_0; + sec.flags |= SEC_ENABLED | SEC_LEVEL; + } + + goto done; + } + + + + sec.enabled = 1; + sec.flags |= SEC_ENABLED; + + if (*crypt != NULL && (*crypt)->ops != NULL && + strcmp((*crypt)->ops->name, "WEP") != 0) { + /* changing to use WEP; deinit previously used algorithm + * on this key */ + ieee80211_crypt_delayed_deinit(ieee, crypt); + } + + if (*crypt == NULL) { + struct ieee80211_crypt_data *new_crypt; + + /* take WEP into use */ + new_crypt = kmalloc(sizeof(struct ieee80211_crypt_data), + GFP_KERNEL); + if (new_crypt == NULL) + return -ENOMEM; + memset(new_crypt, 0, sizeof(struct ieee80211_crypt_data)); + new_crypt->ops = ieee80211_get_crypto_ops("WEP"); + if (!new_crypt->ops) { + request_module("ieee80211_crypt_wep"); + new_crypt->ops = ieee80211_get_crypto_ops("WEP"); + } + + if (new_crypt->ops && try_module_get(new_crypt->ops->owner)) + new_crypt->priv = new_crypt->ops->init(key); + + if (!new_crypt->ops || !new_crypt->priv) { + kfree(new_crypt); + new_crypt = NULL; + + printk(KERN_WARNING "%s: could not initialize WEP: " + "load module ieee80211_crypt_wep\n", + dev->name); + return -EOPNOTSUPP; + } + *crypt = new_crypt; + } + + /* If a new key was provided, set it up */ + if (erq->length > 0) { + len = erq->length <= 5 ? 5 : 13; + memcpy(sec.keys[key], keybuf, erq->length); + if (len > erq->length) + memset(sec.keys[key] + erq->length, 0, + len - erq->length); + IEEE80211_DEBUG_WX("Setting key %d to '%s' (%d:%d bytes)\n", + key, escape_essid(sec.keys[key], len), + erq->length, len); + sec.key_sizes[key] = len; + (*crypt)->ops->set_key(sec.keys[key], len, NULL, + (*crypt)->priv); + sec.flags |= (1 << key); + /* This ensures a key will be activated if no key is + * explicitely set */ + if (key == sec.active_key) + sec.flags |= SEC_ACTIVE_KEY; + } else { + len = (*crypt)->ops->get_key(sec.keys[key], WEP_KEY_LEN, + NULL, (*crypt)->priv); + if (len == 0) { + /* Set a default key of all 0 */ + IEEE80211_DEBUG_WX("Setting key %d to all zero.\n", + key); + memset(sec.keys[key], 0, 13); + (*crypt)->ops->set_key(sec.keys[key], 13, NULL, + (*crypt)->priv); + sec.key_sizes[key] = 13; + sec.flags |= (1 << key); + } + + /* No key data - just set the default TX key index */ + if (key_provided) { + IEEE80211_DEBUG_WX( + "Setting key %d to default Tx key.\n", key); + ieee->tx_keyidx = key; + sec.active_key = key; + sec.flags |= SEC_ACTIVE_KEY; + } + } + + done: + ieee->open_wep = !(erq->flags & IW_ENCODE_RESTRICTED); + sec.auth_mode = ieee->open_wep ? WLAN_AUTH_OPEN : WLAN_AUTH_SHARED_KEY; + sec.flags |= SEC_AUTH_MODE; + IEEE80211_DEBUG_WX("Auth: %s\n", sec.auth_mode == WLAN_AUTH_OPEN ? + "OPEN" : "SHARED KEY"); + + /* For now we just support WEP, so only set that security level... + * TODO: When WPA is added this is one place that needs to change */ + sec.flags |= SEC_LEVEL; + sec.level = SEC_LEVEL_1; /* 40 and 104 bit WEP */ + + if (ieee->set_security) + ieee->set_security(dev, &sec); + + /* Do not reset port if card is in Managed mode since resetting will + * generate new IEEE 802.11 authentication which may end up in looping + * with IEEE 802.1X. If your hardware requires a reset after WEP + * configuration (for example... Prism2), implement the reset_port in + * the callbacks structures used to initialize the 802.11 stack. */ + if (ieee->reset_on_keychange && + ieee->iw_mode != IW_MODE_INFRA && + ieee->reset_port && ieee->reset_port(dev)) { + printk(KERN_DEBUG "%s: reset_port failed\n", dev->name); + return -EINVAL; + } + return 0; +} + +int ieee80211_wx_get_encode(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *keybuf) +{ + struct iw_point *erq = &(wrqu->encoding); + int len, key; + struct ieee80211_crypt_data *crypt; + + IEEE80211_DEBUG_WX("GET_ENCODE\n"); + + key = erq->flags & IW_ENCODE_INDEX; + if (key) { + if (key > WEP_KEYS) + return -EINVAL; + key--; + } else + key = ieee->tx_keyidx; + + crypt = ieee->crypt[key]; + erq->flags = key + 1; + + if (crypt == NULL || crypt->ops == NULL) { + erq->length = 0; + erq->flags |= IW_ENCODE_DISABLED; + return 0; + } + + if (strcmp(crypt->ops->name, "WEP") != 0) { + /* only WEP is supported with wireless extensions, so just + * report that encryption is used */ + erq->length = 0; + erq->flags |= IW_ENCODE_ENABLED; + return 0; + } + + len = crypt->ops->get_key(keybuf, WEP_KEY_LEN, NULL, crypt->priv); + erq->length = (len >= 0 ? len : 0); + + erq->flags |= IW_ENCODE_ENABLED; + + if (ieee->open_wep) + erq->flags |= IW_ENCODE_OPEN; + else + erq->flags |= IW_ENCODE_RESTRICTED; + + return 0; +} + +EXPORT_SYMBOL(ieee80211_wx_get_scan); +EXPORT_SYMBOL(ieee80211_wx_set_encode); +EXPORT_SYMBOL(ieee80211_wx_get_encode); |