diff options
| -rw-r--r-- | Documentation/devicetree/bindings/reset/st,sti-powerdown.txt | 47 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/reset/st,sti-softreset.txt | 46 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih415-clock.dtsi | 14 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih415-pinctrl.dtsi | 204 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih415.dtsi | 70 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih416-clock.dtsi | 14 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih416-pinctrl.dtsi | 197 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih416.dtsi | 67 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih41x-b2000.dtsi | 22 | ||||
| -rw-r--r-- | arch/arm/boot/dts/stih41x-b2020.dtsi | 13 | ||||
| -rw-r--r-- | include/dt-bindings/reset-controller/stih415-resets.h | 26 | ||||
| -rw-r--r-- | include/dt-bindings/reset-controller/stih416-resets.h | 50 |
12 files changed, 770 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt new file mode 100644 index 000000000000..5ab26b7e9d35 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt @@ -0,0 +1,47 @@ +STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip peripheral controllers such as USB and SATA, using +"powerdown" control bits found in the STi family SoC system configuration +registers. These have been grouped together into a single reset controller +device for convenience. + +The actual action taken when powerdown is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "st,<chip>-powerdown" + ex: "st,stih415-powerdown", "st,stih416-powerdown" +- #reset-cells: 1, see below + +example: + + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih415-powerdown"; + }; + + +Specifying powerdown control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the powerdown device node and an +index specifying which channel to use, as described in reset.txt + +example: + + usb1: usb@fe200000 { + resets = <&powerdown STIH41X_USB1_POWERDOWN>; + }; + +Macro definitions for the supported reset channels can be found in: + +include/dt-bindings/reset-controller/stih415-resets.h +include/dt-bindings/reset-controller/stih416-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt new file mode 100644 index 000000000000..a8d3d3c25ca2 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -0,0 +1,46 @@ +STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip peripheral controllers such as USB and SATA, using +"softreset" control bits found in the STi family SoC system configuration +registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "st,<chip>-softreset" example: + "st,stih415-softreset" or "st,stih416-softreset"; +- #reset-cells: 1, see below + +example: + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih415-softreset"; + }; + + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the softreset device node and an +index specifying which channel to use, as described in reset.txt + +example: + + ethernet0{ + resets = <&softreset STIH415_ETH0_SOFTRESET>; + }; + +Macro definitions for the supported reset channels can be found in: + +include/dt-bindings/reset-controller/stih415-resets.h +include/dt-bindings/reset-controller/stih416-resets.h diff --git a/arch/arm/boot/dts/stih415-clock.dtsi b/arch/arm/boot/dts/stih415-clock.dtsi index 174c799df741..d047dbc28d61 100644 --- a/arch/arm/boot/dts/stih415-clock.dtsi +++ b/arch/arm/boot/dts/stih415-clock.dtsi @@ -34,5 +34,19 @@ compatible = "fixed-clock"; clock-frequency = <100000000>; }; + + CLKS_GMAC0_PHY: clockgenA1@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLKS_GMAC0_PHY"; + }; + + CLKS_ETH1_PHY: clockgenA0@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLKS_ETH1_PHY"; + }; }; }; diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi index e56449d41481..f09fb10a3791 100644 --- a/arch/arm/boot/dts/stih415-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi @@ -7,6 +7,7 @@ * publishhed by the Free Software Foundation. */ #include "st-pincfg.h" +#include <dt-bindings/interrupt-controller/arm-gic.h> / { aliases { @@ -45,35 +46,49 @@ #size-cells = <1>; compatible = "st,stih415-sbc-pinctrl"; st,syscfg = <&syscfg_sbc>; + reg = <0xfe61f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe610000 0x5000>; PIO0: gpio@fe610000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO0"; }; PIO1: gpio@fe611000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO1"; }; PIO2: gpio@fe612000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO2"; }; PIO3: gpio@fe613000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO3"; }; PIO4: gpio@fe614000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO4"; }; @@ -104,6 +119,64 @@ }; }; }; + + rc{ + pinctrl_ir: ir0 { + st,pins { + ir = <&PIO4 0 ALT2 IN>; + }; + }; + }; + + gmac1 { + pinctrl_mii1: mii1 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + col = <&PIO0 7 ALT1 IN BYPASS 1000>; + mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + crs = <&PIO1 2 ALT1 IN BYPASS 1000>; + mdint = <&PIO1 3 ALT1 IN BYPASS 0>; + rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>; + }; + }; + + pinctrl_rgmii1: rgmii1-0 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>; + txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>; + + rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>; + + clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>; + }; + }; + }; }; pin-controller-front { @@ -111,53 +184,73 @@ #size-cells = <1>; compatible = "st,stih415-front-pinctrl"; st,syscfg = <&syscfg_front>; + reg = <0xfee0f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfee00000 0x8000>; PIO5: gpio@fee00000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO5"; }; PIO6: gpio@fee01000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO6"; }; PIO7: gpio@fee02000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO7"; }; PIO8: gpio@fee03000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO8"; }; PIO9: gpio@fee04000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO9"; }; PIO10: gpio@fee05000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO10"; }; PIO11: gpio@fee06000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x6000 0x100>; st,bank-name = "PIO11"; }; PIO12: gpio@fee07000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x7000 0x100>; st,bank-name = "PIO12"; }; @@ -186,41 +279,57 @@ #size-cells = <1>; compatible = "st,stih415-rear-pinctrl"; st,syscfg = <&syscfg_rear>; + reg = <0xfe82f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe820000 0x8000>; PIO13: gpio@fe820000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO13"; }; PIO14: gpio@fe821000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO14"; }; PIO15: gpio@fe822000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO15"; }; PIO16: gpio@fe823000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO16"; }; PIO17: gpio@fe824000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO17"; }; PIO18: gpio@fe825000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO18"; }; @@ -233,6 +342,77 @@ }; }; }; + + gmac0{ + pinctrl_mii0: mii0 { + st,pins { + mdint = <&PIO13 6 ALT2 IN BYPASS 0>; + txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + + txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + crs = <&PIO15 2 ALT2 IN BYPASS 1000>; + col = <&PIO15 3 ALT2 IN BYPASS 1000>; + mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + + rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>; + + }; + }; + + pinctrl_gmii0: gmii0 { + st,pins { + mdint = <&PIO13 6 ALT2 IN BYPASS 0>; + mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + + txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + crs = <&PIO15 2 ALT2 IN BYPASS 1000>; + col = <&PIO15 3 ALT2 IN BYPASS 1000>; + rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + + rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + + rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>; + + + }; + }; + }; }; pin-controller-left { @@ -240,23 +420,33 @@ #size-cells = <1>; compatible = "st,stih415-left-pinctrl"; st,syscfg = <&syscfg_left>; + reg = <0xfd6bf080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd6b0000 0x3000>; PIO100: gpio@fd6b0000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO100"; }; PIO101: gpio@fd6b1000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO101"; }; PIO102: gpio@fd6b2000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO102"; }; @@ -267,35 +457,49 @@ #size-cells = <1>; compatible = "st,stih415-right-pinctrl"; st,syscfg = <&syscfg_right>; + reg = <0xfd33f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd330000 0x5000>; PIO103: gpio@fd330000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO103"; }; PIO104: gpio@fd331000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO104"; }; PIO105: gpio@fd332000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO105"; }; PIO106: gpio@fd333000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO106"; }; PIO107: gpio@fd334000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO107"; }; diff --git a/arch/arm/boot/dts/stih415.dtsi b/arch/arm/boot/dts/stih415.dtsi index d9c7dd1d95a4..d89064c20c8a 100644 --- a/arch/arm/boot/dts/stih415.dtsi +++ b/arch/arm/boot/dts/stih415.dtsi @@ -10,6 +10,7 @@ #include "stih415-clock.dtsi" #include "stih415-pinctrl.dtsi" #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset-controller/stih415-resets.h> / { L2: cache-controller { @@ -28,6 +29,16 @@ ranges; compatible = "simple-bus"; + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih415-powerdown"; + }; + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih415-softreset"; + }; + syscfg_sbc: sbc-syscfg@fe600000{ compatible = "st,stih415-sbc-syscfg", "syscon"; reg = <0xfe600000 0xb4>; @@ -136,5 +147,64 @@ status = "disabled"; }; + + ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610"; + status = "disabled"; + + reg = <0xfe810000 0x8000>, <0x148 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + + interrupts = <0 147 0>, <0 148 0>, <0 149 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + resets = <&softreset STIH415_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + + snps,pbl = <32>; + snps,mixed-burst; + snps,force_sf_dma_mode; + + st,syscon = <&syscfg_rear>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii0>; + clock-names = "stmmaceth"; + clocks = <&CLKS_GMAC0_PHY>; + }; + + ethernet1: dwmac@fef08000 { + device_type = "network"; + compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610"; + status = "disabled"; + reg = <0xfef08000 0x8000>, <0x74 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 150 0>, <0 151 0>, <0 152 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + snps,force_sf_dma_mode; + + st,syscon = <&syscfg_sbc>; + + resets = <&softreset STIH415_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii1>; + clock-names = "stmmaceth"; + clocks = <&CLKS_ETH1_PHY>; + }; + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + clocks = <&CLK_SYSIN>; + rx-mode = "infrared"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ir>; + resets = <&softreset STIH415_IRB_SOFTRESET>; + }; }; }; diff --git a/arch/arm/boot/dts/stih416-clock.dtsi b/arch/arm/boot/dts/stih416-clock.dtsi index 7026bf1158d8..a6942c75cbbb 100644 --- a/arch/arm/boot/dts/stih416-clock.dtsi +++ b/arch/arm/boot/dts/stih416-clock.dtsi @@ -37,5 +37,19 @@ clock-frequency = <100000000>; clock-output-names = "CLK_S_ICN_REG_0"; }; + + CLK_S_GMAC0_PHY: clockgenA1@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLK_S_GMAC0_PHY"; + }; + + CLK_S_ETH1_PHY: clockgenA0@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLK_S_ETH1_PHY"; + }; }; }; diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi index b29ff4ba542c..e7f8b5f4460a 100644 --- a/arch/arm/boot/dts/stih416-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi @@ -8,6 +8,7 @@ * publishhed by the Free Software Foundation. */ #include "st-pincfg.h" +#include <dt-bindings/interrupt-controller/arm-gic.h> / { aliases { @@ -49,46 +50,69 @@ #size-cells = <1>; compatible = "st,stih416-sbc-pinctrl"; st,syscfg = <&syscfg_sbc>; + reg = <0xfe61f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe610000 0x6000>; PIO0: gpio@fe610000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO0"; }; PIO1: gpio@fe611000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO1"; }; PIO2: gpio@fe612000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO2"; }; PIO3: gpio@fe613000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO3"; }; PIO4: gpio@fe614000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO4"; }; PIO40: gpio@fe615000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO40"; st,retime-pin-mask = <0x7f>; }; + rc{ + pinctrl_ir: ir0 { + st,pins { + ir = <&PIO4 0 ALT2 IN>; + }; + }; + }; sbc_serial1 { pinctrl_sbc_serial1: sbc_serial1 { st,pins { @@ -115,6 +139,58 @@ }; }; }; + + gmac1 { + pinctrl_mii1: mii1 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + col = <&PIO0 7 ALT1 IN BYPASS 1000>; + + mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + crs = <&PIO1 2 ALT1 IN BYPASS 1000>; + mdint = <&PIO1 3 ALT1 IN BYPASS 0>; + rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>; + + rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>; + }; + }; + pinctrl_rgmii1: rgmii1-0 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>; + txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + + mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>; + + rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>; + + clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>; + }; + }; + }; }; pin-controller-front { @@ -122,65 +198,89 @@ #size-cells = <1>; compatible = "st,stih416-front-pinctrl"; st,syscfg = <&syscfg_front>; + reg = <0xfee0f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfee00000 0x10000>; PIO5: gpio@fee00000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO5"; }; PIO6: gpio@fee01000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO6"; }; PIO7: gpio@fee02000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO7"; }; PIO8: gpio@fee03000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO8"; }; PIO9: gpio@fee04000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO9"; }; PIO10: gpio@fee05000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO10"; }; PIO11: gpio@fee06000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x6000 0x100>; st,bank-name = "PIO11"; }; PIO12: gpio@fee07000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x7000 0x100>; st,bank-name = "PIO12"; }; PIO30: gpio@fee08000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x8000 0x100>; st,bank-name = "PIO30"; }; PIO31: gpio@fee09000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x9000 0x100>; st,bank-name = "PIO31"; }; @@ -217,41 +317,57 @@ #size-cells = <1>; compatible = "st,stih416-rear-pinctrl"; st,syscfg = <&syscfg_rear>; + reg = <0xfe82f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe820000 0x6000>; PIO13: gpio@fe820000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO13"; }; PIO14: gpio@fe821000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO14"; }; PIO15: gpio@fe822000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO15"; }; PIO16: gpio@fe823000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO16"; }; PIO17: gpio@fe824000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO17"; }; PIO18: gpio@fe825000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO18"; st,retime-pin-mask = <0xf>; @@ -265,6 +381,63 @@ }; }; }; + + gmac0 { + pinctrl_mii0: mii0 { + st,pins { + mdint = <&PIO13 6 ALT2 IN BYPASS 0>; + txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + crs = <&PIO15 2 ALT2 IN BYPASS 1000>; + col = <&PIO15 3 ALT2 IN BYPASS 1000>; + mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + + rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>; + }; + }; + + pinctrl_gmii0: gmii0 { + st,pins { + }; + }; + pinctrl_rgmii0: rgmii0 { + st,pins { + phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>; + txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>; + txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>; + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + + mdio = <&PIO15 4 ALT2 OUT BYPASS 0>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + + rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>; + rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>; + rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>; + rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>; + rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>; + rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + + clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>; + }; + }; + }; }; pin-controller-fvdp-fe { @@ -272,23 +445,33 @@ #size-cells = <1>; compatible = "st,stih416-fvdp-fe-pinctrl"; st,syscfg = <&syscfg_fvdp_fe>; + reg = <0xfd6bf080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd6b0000 0x3000>; PIO100: gpio@fd6b0000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO100"; }; PIO101: gpio@fd6b1000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO101"; }; PIO102: gpio@fd6b2000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO102"; }; @@ -299,29 +482,41 @@ #size-cells = <1>; compatible = "st,stih416-fvdp-lite-pinctrl"; st,syscfg = <&syscfg_fvdp_lite>; + reg = <0xfd33f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd330000 0x5000>; PIO103: gpio@fd330000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO103"; }; PIO104: gpio@fd331000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO104"; }; PIO105: gpio@fd332000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO105"; }; PIO106: gpio@fd333000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO106"; }; @@ -329,6 +524,8 @@ PIO107: gpio@fd334000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO107"; st,retime-pin-mask = <0xf>; diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi index b7ab47b95816..8299a7b8fee8 100644 --- a/arch/arm/boot/dts/stih416.dtsi +++ b/arch/arm/boot/dts/stih416.dtsi @@ -10,6 +10,7 @@ #include "stih416-clock.dtsi" #include "stih416-pinctrl.dtsi" #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset-controller/stih416-resets.h> / { L2: cache-controller { compatible = "arm,pl310-cache"; @@ -27,6 +28,16 @@ ranges; compatible = "simple-bus"; + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih416-powerdown"; + }; + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih416-softreset"; + }; + syscfg_sbc:sbc-syscfg@fe600000{ compatible = "st,stih416-sbc-syscfg", "syscon"; reg = <0xfe600000 0x1000>; @@ -145,5 +156,61 @@ status = "disabled"; }; + + ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + status = "disabled"; + reg = <0xfe810000 0x8000>, <0x8bc 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + + interrupts = <0 133 0>, <0 134 0>, <0 135 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + st,syscon = <&syscfg_rear>; + resets = <&softreset STIH416_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii0>; + clock-names = "stmmaceth"; + clocks = <&CLK_S_GMAC0_PHY>; + }; + + ethernet1: dwmac@fef08000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + status = "disabled"; + reg = <0xfef08000 0x8000>, <0x7f0 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 136 0>, <0 137 0>, <0 138 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + st,syscon = <&syscfg_sbc>; + + resets = <&softreset STIH416_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii1>; + clock-names = "stmmaceth"; + clocks = <&CLK_S_ETH1_PHY>; + }; + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + rx-mode = "infrared"; + clocks = <&CLK_SYSIN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ir>; + resets = <&softreset STIH416_IRB_SOFTRESET>; + }; + }; }; diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi index 1e6aa92772f5..bf65c49095af 100644 --- a/arch/arm/boot/dts/stih41x-b2000.dtsi +++ b/arch/arm/boot/dts/stih41x-b2000.dtsi @@ -20,6 +20,8 @@ aliases { ttyAS0 = &serial2; + ethernet0 = ðernet0; + ethernet1 = ðernet1; }; soc { @@ -46,5 +48,25 @@ status = "okay"; }; + + ethernet0: dwmac@fe810000 { + status = "okay"; + phy-mode = "mii"; + pinctrl-0 = <&pinctrl_mii0>; + + snps,reset-gpio = <&PIO106 2>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + }; + + ethernet1: dwmac@fef08000 { + status = "disabled"; + phy-mode = "mii"; + st,tx-retime-src = "txclk"; + + snps,reset-gpio = <&PIO4 7>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + }; }; }; diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi index 0ef0a69df8ea..3dc74c25a57b 100644 --- a/arch/arm/boot/dts/stih41x-b2020.dtsi +++ b/arch/arm/boot/dts/stih41x-b2020.dtsi @@ -19,6 +19,7 @@ aliases { ttyAS0 = &sbc_serial1; + ethernet1 = ðernet1; }; soc { sbc_serial1: serial@fe531000 { @@ -60,5 +61,17 @@ i2c@fe541000 { status = "okay"; }; + + ethernet1: dwmac@fef08000 { + status = "okay"; + phy-mode = "rgmii-id"; + max-speed = <1000>; + st,tx-retime-src = "clk_125"; + snps,reset-gpio = <&PIO3 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + + pinctrl-0 = <&pinctrl_rgmii1>; + }; }; }; diff --git a/include/dt-bindings/reset-controller/stih415-resets.h b/include/dt-bindings/reset-controller/stih415-resets.h new file mode 100644 index 000000000000..c2f8a66913c5 --- /dev/null +++ b/include/dt-bindings/reset-controller/stih415-resets.h @@ -0,0 +1,26 @@ +/* + * This header provides constants for the reset controller + * based peripheral powerdown requests on the STMicroelectronics + * STiH415 SoC. + */ +#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415 +#define _DT_BINDINGS_RESET_CONTROLLER_STIH415 + +#define STIH415_EMISS_POWERDOWN 0 +#define STIH415_NAND_POWERDOWN 1 +#define STIH415_KEYSCAN_POWERDOWN 2 +#define STIH415_USB0_POWERDOWN 3 +#define STIH415_USB1_POWERDOWN 4 +#define STIH415_USB2_POWERDOWN 5 +#define STIH415_SATA0_POWERDOWN 6 +#define STIH415_SATA1_POWERDOWN 7 +#define STIH415_PCIE_POWERDOWN 8 + +#define STIH415_ETH0_SOFTRESET 0 +#define STIH415_ETH1_SOFTRESET 1 +#define STIH415_IRB_SOFTRESET 2 +#define STIH415_USB0_SOFTRESET 3 +#define STIH415_USB1_SOFTRESET 4 +#define STIH415_USB2_SOFTRESET 5 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */ diff --git a/include/dt-bindings/reset-controller/stih416-resets.h b/include/dt-bindings/reset-controller/stih416-resets.h new file mode 100644 index 000000000000..2127743f23e3 --- /dev/null +++ b/include/dt-bindings/reset-controller/stih416-resets.h @@ -0,0 +1,50 @@ +/* + * This header provides constants for the reset controller + * based peripheral powerdown requests on the STMicroelectronics + * STiH416 SoC. + */ +#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH416 +#define _DT_BINDINGS_RESET_CONTROLLER_STIH416 + +#define STIH416_EMISS_POWERDOWN 0 +#define STIH416_NAND_POWERDOWN 1 +#define STIH416_KEYSCAN_POWERDOWN 2 +#define STIH416_USB0_POWERDOWN 3 +#define STIH416_USB1_POWERDOWN 4 +#define STIH416_USB2_POWERDOWN 5 +#define STIH416_USB3_POWERDOWN 6 +#define STIH416_SATA0_POWERDOWN 7 +#define STIH416_SATA1_POWERDOWN 8 +#define STIH416_PCIE0_POWERDOWN 9 +#define STIH416_PCIE1_POWERDOWN 10 + +#define STIH416_ETH0_SOFTRESET 0 +#define STIH416_ETH1_SOFTRESET 1 +#define STIH416_IRB_SOFTRESET 2 +#define STIH416_USB0_SOFTRESET 3 +#define STIH416_USB1_SOFTRESET 4 +#define STIH416_USB2_SOFTRESET 5 +#define STIH416_USB3_SOFTRESET 6 +#define STIH416_SATA0_SOFTRESET 7 +#define STIH416_SATA1_SOFTRESET 8 +#define STIH416_PCIE0_SOFTRESET 9 +#define STIH416_PCIE1_SOFTRESET 10 +#define STIH416_AUD_DAC_SOFTRESET 11 +#define STIH416_HDTVOUT_SOFTRESET 12 +#define STIH416_VTAC_M_RX_SOFTRESET 13 +#define STIH416_VTAC_A_RX_SOFTRESET 14 +#define STIH416_SYNC_HD_SOFTRESET 15 +#define STIH416_SYNC_SD_SOFTRESET 16 +#define STIH416_BLITTER_SOFTRESET 17 +#define STIH416_GPU_SOFTRESET 18 +#define STIH416_VTAC_M_TX_SOFTRESET 19 +#define STIH416_VTAC_A_TX_SOFTRESET 20 +#define STIH416_VTG_AUX_SOFTRESET 21 +#define STIH416_JPEG_DEC_SOFTRESET 22 +#define STIH416_HVA_SOFTRESET 23 +#define STIH416_COMPO_M_SOFTRESET 24 +#define STIH416_COMPO_A_SOFTRESET 25 +#define STIH416_VP8_DEC_SOFTRESET 26 +#define STIH416_VTG_MAIN_SOFTRESET 27 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH416 */ |