summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/plat-omap/include/plat/omap-serial.h129
-rw-r--r--drivers/serial/Kconfig27
-rw-r--r--drivers/serial/Makefile1
-rw-r--r--drivers/serial/omap-serial.c1333
-rw-r--r--include/linux/serial_core.h3
5 files changed, 1493 insertions, 0 deletions
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
new file mode 100644
index 000000000000..0d6f076cf748
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -0,0 +1,129 @@
+/*
+ * Driver for OMAP-UART controller.
+ * Based on drivers/serial/8250.c
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * Authors:
+ * Govindraj R <govindraj.raja@ti.com>
+ * Thara Gopinath <thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __OMAP_SERIAL_H__
+#define __OMAP_SERIAL_H__
+
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+
+#include <plat/control.h>
+#include <plat/mux.h>
+
+#define DRIVER_NAME "omap-hsuart"
+
+/*
+ * Use tty device name as ttyO, [O -> OMAP]
+ * in bootargs we specify as console=ttyO0 if uart1
+ * is used as console uart.
+ */
+#define OMAP_SERIAL_NAME "ttyO"
+
+#define OMAP_MDR1_DISABLE 0x07
+#define OMAP_MDR1_MODE13X 0x03
+#define OMAP_MDR1_MODE16X 0x00
+#define OMAP_MODE13X_SPEED 230400
+
+/*
+ * LCR = 0XBF: Switch to Configuration Mode B.
+ * In configuration mode b allow access
+ * to EFR,DLL,DLH.
+ * Reference OMAP TRM Chapter 17
+ * Section: 1.4.3 Mode Selection
+ */
+#define OMAP_UART_LCR_CONF_MDB 0XBF
+
+/* WER = 0x7F
+ * Enable module level wakeup in WER reg
+ */
+#define OMAP_UART_WER_MOD_WKUP 0X7F
+
+/* Enable XON/XOFF flow control on output */
+#define OMAP_UART_SW_TX 0x04
+
+/* Enable XON/XOFF flow control on input */
+#define OMAP_UART_SW_RX 0x04
+
+#define OMAP_UART_SYSC_RESET 0X07
+#define OMAP_UART_TCR_TRIG 0X0F
+#define OMAP_UART_SW_CLR 0XF0
+#define OMAP_UART_FIFO_CLR 0X06
+
+#define OMAP_UART_DMA_CH_FREE -1
+
+#define RX_TIMEOUT (3 * HZ)
+#define OMAP_MAX_HSUART_PORTS 4
+
+#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
+
+struct omap_uart_port_info {
+ bool dma_enabled; /* To specify DMA Mode */
+ unsigned int uartclk; /* UART clock rate */
+ void __iomem *membase; /* ioremap cookie or NULL */
+ resource_size_t mapbase; /* resource base */
+ unsigned long irqflags; /* request_irq flags */
+ upf_t flags; /* UPF_* flags */
+};
+
+struct uart_omap_dma {
+ u8 uart_dma_tx;
+ u8 uart_dma_rx;
+ int rx_dma_channel;
+ int tx_dma_channel;
+ dma_addr_t rx_buf_dma_phys;
+ dma_addr_t tx_buf_dma_phys;
+ unsigned int uart_base;
+ /*
+ * Buffer for rx dma.It is not required for tx because the buffer
+ * comes from port structure.
+ */
+ unsigned char *rx_buf;
+ unsigned int prev_rx_dma_pos;
+ int tx_buf_size;
+ int tx_dma_used;
+ int rx_dma_used;
+ spinlock_t tx_lock;
+ spinlock_t rx_lock;
+ /* timer to poll activity on rx dma */
+ struct timer_list rx_timer;
+ int rx_buf_size;
+ int rx_timeout;
+};
+
+struct uart_omap_port {
+ struct uart_port port;
+ struct uart_omap_dma uart_dma;
+ struct platform_device *pdev;
+
+ unsigned char ier;
+ unsigned char lcr;
+ unsigned char mcr;
+ unsigned char fcr;
+ unsigned char efr;
+
+ int use_dma;
+ /*
+ * Some bits in registers are cleared on a read, so they must
+ * be saved whenever the register is read but the bits will not
+ * be immediately processed.
+ */
+ unsigned int lsr_break_flag;
+ unsigned char msr_saved_flags;
+ char name[20];
+ unsigned long port_activity;
+};
+
+#endif /* __OMAP_SERIAL_H__ */
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 12900f7083b0..8d8b975ce784 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -1416,6 +1416,33 @@ config SERIAL_OF_PLATFORM
Currently, only 8250 compatible ports are supported, but
others can easily be added.
+config SERIAL_OMAP
+ tristate "OMAP serial port support"
+ depends on ARCH_OMAP2 || ARCH_OMAP3 || ARCH_OMAP4
+ select SERIAL_CORE
+ help
+ If you have a machine based on an Texas Instruments OMAP CPU you
+ can enable its onboard serial ports by enabling this option.
+
+ By enabling this option you take advantage of dma feature available
+ with the omap-serial driver. DMA support can be enabled from platform
+ data.
+
+config SERIAL_OMAP_CONSOLE
+ bool "Console on OMAP serial port"
+ depends on SERIAL_OMAP
+ select SERIAL_CORE_CONSOLE
+ help
+ Select this option if you would like to use omap serial port as
+ console.
+
+ Even if you say Y here, the currently visible virtual console
+ (/dev/tty0) will still be used as the system console by default, but
+ you can alter that using a kernel command line option such as
+ "console=ttyOx". (Try "man bootparam" or see the documentation of
+ your boot loader about how to pass options to the kernel at
+ boot time.)
+
config SERIAL_OF_PLATFORM_NWPSERIAL
tristate "NWP serial port driver"
depends on PPC_OF && PPC_DCR
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 1ca4fd599ffe..c5705765454f 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -88,3 +88,4 @@ obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o
obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
obj-$(CONFIG_SERIAL_MRST_MAX3110) += mrst_max3110.o
obj-$(CONFIG_SERIAL_MFD_HSU) += mfd.o
+obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
diff --git a/drivers/serial/omap-serial.c b/drivers/serial/omap-serial.c
new file mode 100644
index 000000000000..2ee1d3282a8c
--- /dev/null
+++ b/drivers/serial/omap-serial.c
@@ -0,0 +1,1333 @@
+/*
+ * Driver for OMAP-UART controller.
+ * Based on drivers/serial/8250.c
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * Authors:
+ * Govindraj R <govindraj.raja@ti.com>
+ * Thara Gopinath <thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Note: This driver is made seperate from 8250 driver as we cannot
+ * over load 8250 driver with omap platform specific configuration for
+ * features like DMA, it makes easier to implement features like DMA and
+ * hardware flow control and software flow control configuration with
+ * this driver as required for the omap-platform.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/serial_reg.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/io.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+#include <linux/serial_core.h>
+#include <linux/irq.h>
+
+#include <plat/dma.h>
+#include <plat/dmtimer.h>
+#include <plat/omap-serial.h>
+
+static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
+
+/* Forward declaration of functions */
+static void uart_tx_dma_callback(int lch, u16 ch_status, void *data);
+static void serial_omap_rx_timeout(unsigned long uart_no);
+static int serial_omap_start_rxdma(struct uart_omap_port *up);
+
+static inline unsigned int serial_in(struct uart_omap_port *up, int offset)
+{
+ offset <<= up->port.regshift;
+ return readw(up->port.membase + offset);
+}
+
+static inline void serial_out(struct uart_omap_port *up, int offset, int value)
+{
+ offset <<= up->port.regshift;
+ writew(value, up->port.membase + offset);
+}
+
+static inline void serial_omap_clear_fifos(struct uart_omap_port *up)
+{
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+ serial_out(up, UART_FCR, 0);
+}
+
+/*
+ * serial_omap_get_divisor - calculate divisor value
+ * @port: uart port info
+ * @baud: baudrate for which divisor needs to be calculated.
+ *
+ * We have written our own function to get the divisor so as to support
+ * 13x mode. 3Mbps Baudrate as an different divisor.
+ * Reference OMAP TRM Chapter 17:
+ * Table 17-1. UART Mode Baud Rates, Divisor Values, and Error Rates
+ * referring to oversampling - divisor value
+ * baudrate 460,800 to 3,686,400 all have divisor 13
+ * except 3,000,000 which has divisor value 16
+ */
+static unsigned int
+serial_omap_get_divisor(struct uart_port *port, unsigned int baud)
+{
+ unsigned int divisor;
+
+ if (baud > OMAP_MODE13X_SPEED && baud != 3000000)
+ divisor = 13;
+ else
+ divisor = 16;
+ return port->uartclk/(baud * divisor);
+}
+
+static void serial_omap_stop_rxdma(struct uart_omap_port *up)
+{
+ if (up->uart_dma.rx_dma_used) {
+ del_timer(&up->uart_dma.rx_timer);
+ omap_stop_dma(up->uart_dma.rx_dma_channel);
+ omap_free_dma(up->uart_dma.rx_dma_channel);
+ up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
+ up->uart_dma.rx_dma_used = false;
+ }
+}
+
+static void serial_omap_enable_ms(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+ dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->pdev->id);
+ up->ier |= UART_IER_MSI;
+ serial_out(up, UART_IER, up->ier);
+}
+
+static void serial_omap_stop_tx(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+ if (up->use_dma &&
+ up->uart_dma.tx_dma_channel != OMAP_UART_DMA_CH_FREE) {
+ /*
+ * Check if dma is still active. If yes do nothing,
+ * return. Else stop dma
+ */
+ if (omap_get_dma_active_status(up->uart_dma.tx_dma_channel))
+ return;
+ omap_stop_dma(up->uart_dma.tx_dma_channel);
+ omap_free_dma(up->uart_dma.tx_dma_channel);
+ up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
+ }
+
+ if (up->ier & UART_IER_THRI) {
+ up->ier &= ~UART_IER_THRI;
+ serial_out(up, UART_IER, up->ier);
+ }
+}
+
+static void serial_omap_stop_rx(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+ if (up->use_dma)
+ serial_omap_stop_rxdma(up);
+ up->ier &= ~UART_IER_RLSI;
+ up->port.read_status_mask &= ~UART_LSR_DR;
+ serial_out(up, UART_IER, up->ier);
+}
+
+static inline void receive_chars(struct uart_omap_port *up, int *status)
+{
+ struct tty_struct *tty = up->port.state->port.tty;
+ unsigned int flag;
+ unsigned char ch, lsr = *status;
+ int max_count = 256;
+
+ do {
+ if (likely(lsr & UART_LSR_DR))
+ ch = serial_in(up, UART_RX);
+ flag = TTY_NORMAL;
+ up->port.icount.rx++;
+
+ if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
+ /*
+ * For statistics only
+ */
+ if (lsr & UART_LSR_BI) {
+ lsr &= ~(UART_LSR_FE | UART_LSR_PE);
+ up->port.icount.brk++;
+ /*
+ * We do the SysRQ and SAK checking
+ * here because otherwise the break
+ * may get masked by ignore_status_mask
+ * or read_status_mask.
+ */
+ if (uart_handle_break(&up->port))
+ goto ignore_char;
+ } else if (lsr & UART_LSR_PE) {
+ up->port.icount.parity++;
+ } else if (lsr & UART_LSR_FE) {
+ up->port.icount.frame++;
+ }
+
+ if (lsr & UART_LSR_OE)
+ up->port.icount.overrun++;
+
+ /*
+ * Mask off conditions which should be ignored.
+ */
+ lsr &= up->port.read_status_mask;
+
+#ifdef CONFIG_SERIAL_OMAP_CONSOLE
+ if (up->port.line == up->port.cons->index) {
+ /* Recover the break flag from console xmit */
+ lsr |= up->lsr_break_flag;
+ up->lsr_break_flag = 0;
+ }
+#endif
+ if (lsr & UART_LSR_BI)
+ flag = TTY_BREAK;
+ else if (lsr & UART_LSR_PE)
+ flag = TTY_PARITY;
+ else if (lsr & UART_LSR_FE)
+ flag = TTY_FRAME;
+ }
+
+ if (uart_handle_sysrq_char(&up->port, ch))
+ goto ignore_char;
+ uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
+ignore_char:
+ lsr = serial_in(up, UART_LSR);
+ } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (max_count-- > 0));
+ spin_unlock(&up->port.lock);
+ tty_flip_buffer_push(tty);
+ spin_lock(&up->port.lock);
+}
+
+static void transmit_chars(struct uart_omap_port *up)
+{
+ struct circ_buf *xmit = &up->port.state->xmit;
+ int count;
+
+ if (up->port.x_char) {
+ serial_out(up, UART_TX, up->port.x_char);
+ up->port.icount.tx++;
+ up->port.x_char = 0;
+ return;
+ }
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
+ serial_omap_stop_tx(&up->port);
+ return;
+ }
+ count = up->port.fifosize / 4;
+ do {
+ serial_out(up, UART_TX, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ up->port.icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (--count > 0);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&up->port);
+
+ if (uart_circ_empty(xmit))
+ serial_omap_stop_tx(&up->port);
+}
+
+static inline void serial_omap_enable_ier_thri(struct uart_omap_port *up)
+{
+ if (!(up->ier & UART_IER_THRI)) {
+ up->ier |= UART_IER_THRI;
+ serial_out(up, UART_IER, up->ier);
+ }
+}
+
+static void serial_omap_start_tx(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ struct circ_buf *xmit;
+ unsigned int start;
+ int ret = 0;
+
+ if (!up->use_dma) {
+ serial_omap_enable_ier_thri(up);
+ return;
+ }
+
+ if (up->uart_dma.tx_dma_used)
+ return;
+
+ xmit = &up->port.state->xmit;
+
+ if (up->uart_dma.tx_dma_channel == OMAP_UART_DMA_CH_FREE) {
+ ret = omap_request_dma(up->uart_dma.uart_dma_tx,
+ "UART Tx DMA",
+ (void *)uart_tx_dma_callback, up,
+ &(up->uart_dma.tx_dma_channel));
+
+ if (ret < 0) {
+ serial_omap_enable_ier_thri(up);
+ return;
+ }
+ }
+ spin_lock(&(up->uart_dma.tx_lock));
+ up->uart_dma.tx_dma_used = true;
+ spin_unlock(&(up->uart_dma.tx_lock));
+
+ start = up->uart_dma.tx_buf_dma_phys +
+ (xmit->tail & (UART_XMIT_SIZE - 1));
+
+ up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
+ /*
+ * It is a circular buffer. See if the buffer has wounded back.
+ * If yes it will have to be transferred in two separate dma
+ * transfers
+ */
+ if (start + up->uart_dma.tx_buf_size >=
+ up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
+ up->uart_dma.tx_buf_size =
+ (up->uart_dma.tx_buf_dma_phys +
+ UART_XMIT_SIZE) - start;
+
+ omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ up->uart_dma.uart_base, 0, 0);
+ omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
+ OMAP_DMA_AMODE_POST_INC, start, 0, 0);
+ omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
+ OMAP_DMA_DATA_TYPE_S8,
+ up->uart_dma.tx_buf_size, 1,
+ OMAP_DMA_SYNC_ELEMENT,
+ up->uart_dma.uart_dma_tx, 0);
+ /* FIXME: Cache maintenance needed here? */
+ omap_start_dma(up->uart_dma.tx_dma_channel);
+}
+
+static unsigned int check_modem_status(struct uart_omap_port *up)
+{
+ unsigned int status;
+
+ status = serial_in(up, UART_MSR);
+ status |= up->msr_saved_flags;
+ up->msr_saved_flags = 0;
+ if ((status & UART_MSR_ANY_DELTA) == 0)
+ return status;
+
+ if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
+ up->port.state != NULL) {
+ if (status & UART_MSR_TERI)
+ up->port.icount.rng++;
+ if (status & UART_MSR_DDSR)
+ up->port.icount.dsr++;
+ if (status & UART_MSR_DDCD)
+ uart_handle_dcd_change
+ (&up->port, status & UART_MSR_DCD);
+ if (status & UART_MSR_DCTS)
+ uart_handle_cts_change
+ (&up->port, status & UART_MSR_CTS);
+ wake_up_interruptible(&up->port.state->port.delta_msr_wait);
+ }
+
+ return status;
+}
+
+/**
+ * serial_omap_irq() - This handles the interrupt from one port
+ * @irq: uart port irq number
+ * @dev_id: uart port info
+ */
+static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
+{
+ struct uart_omap_port *up = dev_id;
+ unsigned int iir, lsr;
+ unsigned long flags;
+
+ iir = serial_in(up, UART_IIR);
+ if (iir & UART_IIR_NO_INT)
+ return IRQ_NONE;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ lsr = serial_in(up, UART_LSR);
+ if (iir & UART_IIR_RLSI) {
+ if (!up->use_dma) {
+ if (lsr & UART_LSR_DR)
+ receive_chars(up, &lsr);
+ } else {
+ up->ier &= ~(UART_IER_RDI | UART_IER_RLSI);
+ serial_out(up, UART_IER, up->ier);
+ if ((serial_omap_start_rxdma(up) != 0) &&
+ (lsr & UART_LSR_DR))
+ receive_chars(up, &lsr);
+ }
+ }
+
+ check_modem_status(up);
+ if ((lsr & UART_LSR_THRE) && (iir & UART_IIR_THRI))
+ transmit_chars(up);
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
+ up->port_activity = jiffies;
+ return IRQ_HANDLED;
+}
+
+static unsigned int serial_omap_tx_empty(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned long flags = 0;
+ unsigned int ret = 0;
+
+ dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->pdev->id);
+ spin_lock_irqsave(&up->port.lock, flags);
+ ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ return ret;
+}
+
+static unsigned int serial_omap_get_mctrl(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned char status;
+ unsigned int ret = 0;
+
+ status = check_modem_status(up);
+ dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->pdev->id);
+
+ if (status & UART_MSR_DCD)
+ ret |= TIOCM_CAR;
+ if (status & UART_MSR_RI)
+ ret |= TIOCM_RNG;
+ if (status & UART_MSR_DSR)
+ ret |= TIOCM_DSR;
+ if (status & UART_MSR_CTS)
+ ret |= TIOCM_CTS;
+ return ret;
+}
+
+static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned char mcr = 0;
+
+ dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->pdev->id);
+ if (mctrl & TIOCM_RTS)
+ mcr |= UART_MCR_RTS;
+ if (mctrl & TIOCM_DTR)
+ mcr |= UART_MCR_DTR;
+ if (mctrl & TIOCM_OUT1)
+ mcr |= UART_MCR_OUT1;
+ if (mctrl & TIOCM_OUT2)
+ mcr |= UART_MCR_OUT2;
+ if (mctrl & TIOCM_LOOP)
+ mcr |= UART_MCR_LOOP;
+
+ mcr |= up->mcr;
+ serial_out(up, UART_MCR, mcr);
+}
+
+static void serial_omap_break_ctl(struct uart_port *port, int break_state)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned long flags = 0;
+
+ dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->pdev->id);
+ spin_lock_irqsave(&up->port.lock, flags);
+ if (break_state == -1)
+ up->lcr |= UART_LCR_SBC;
+ else
+ up->lcr &= ~UART_LCR_SBC;
+ serial_out(up, UART_LCR, up->lcr);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static int serial_omap_startup(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned long flags = 0;
+ int retval;
+
+ /*
+ * Allocate the IRQ
+ */
+ retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags,
+ up->name, up);
+ if (retval)
+ return retval;
+
+ dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->pdev->id);
+
+ /*
+ * Clear the FIFO buffers and disable them.
+ * (they will be reenabled in set_termios())
+ */
+ serial_omap_clear_fifos(up);
+ /* For Hardware flow control */
+ serial_out(up, UART_MCR, UART_MCR_RTS);
+
+ /*
+ * Clear the interrupt registers.
+ */
+ (void) serial_in(up, UART_LSR);
+ if (serial_in(up, UART_LSR) & UART_LSR_DR)
+ (void) serial_in(up, UART_RX);
+ (void) serial_in(up, UART_IIR);
+ (void) serial_in(up, UART_MSR);
+
+ /*
+ * Now, initialize the UART
+ */
+ serial_out(up, UART_LCR, UART_LCR_WLEN8);
+ spin_lock_irqsave(&up->port.lock, flags);
+ /*
+ * Most PC uarts need OUT2 raised to enable interrupts.
+ */
+ up->port.mctrl |= TIOCM_OUT2;
+ serial_omap_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ up->msr_saved_flags = 0;
+ if (up->use_dma) {
+ free_page((unsigned long)up->port.state->xmit.buf);
+ up->port.state->xmit.buf = dma_alloc_coherent(NULL,
+ UART_XMIT_SIZE,
+ (dma_addr_t *)&(up->uart_dma.tx_buf_dma_phys),
+ 0);
+ init_timer(&(up->uart_dma.rx_timer));
+ up->uart_dma.rx_timer.function = serial_omap_rx_timeout;
+ up->uart_dma.rx_timer.data = up->pdev->id;
+ /* Currently the buffer size is 4KB. Can increase it */
+ up->uart_dma.rx_buf = dma_alloc_coherent(NULL,
+ up->uart_dma.rx_buf_size,
+ (dma_addr_t *)&(up->uart_dma.rx_buf_dma_phys), 0);
+ }
+ /*
+ * Finally, enable interrupts. Note: Modem status interrupts
+ * are set via set_termios(), which will be occurring imminently
+ * anyway, so we don't enable them here.
+ */
+ up->ier = UART_IER_RLSI | UART_IER_RDI;
+ serial_out(up, UART_IER, up->ier);
+
+ up->port_activity = jiffies;
+ return 0;
+}
+
+static void serial_omap_shutdown(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned long flags = 0;
+
+ dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->pdev->id);
+ /*
+ * Disable interrupts from this port
+ */
+ up->ier = 0;
+ serial_out(up, UART_IER, 0);
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ up->port.mctrl &= ~TIOCM_OUT2;
+ serial_omap_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ /*
+ * Disable break condition and FIFOs
+ */
+ serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
+ serial_omap_clear_fifos(up);
+
+ /*
+ * Read data port to reset things, and then free the irq
+ */
+ if (serial_in(up, UART_LSR) & UART_LSR_DR)
+ (void) serial_in(up, UART_RX);
+ if (up->use_dma) {
+ dma_free_coherent(up->port.dev,
+ UART_XMIT_SIZE, up->port.state->xmit.buf,
+ up->uart_dma.tx_buf_dma_phys);
+ up->port.state->xmit.buf = NULL;
+ serial_omap_stop_rx(port);
+ dma_free_coherent(up->port.dev,
+ up->uart_dma.rx_buf_size, up->uart_dma.rx_buf,
+ up->uart_dma.rx_buf_dma_phys);
+ up->uart_dma.rx_buf = NULL;
+ }
+ free_irq(up->port.irq, up);
+}
+
+static inline void
+serial_omap_configure_xonxoff
+ (struct uart_omap_port *up, struct ktermios *termios)
+{
+ unsigned char efr = 0;
+
+ up->lcr = serial_in(up, UART_LCR);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+ up->efr = serial_in(up, UART_EFR);
+ serial_out(up, UART_EFR, up->efr & ~UART_EFR_ECB);
+
+ serial_out(up, UART_XON1, termios->c_cc[VSTART]);
+ serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);
+
+ /* clear SW control mode bits */
+ efr = up->efr;
+ efr &= OMAP_UART_SW_CLR;
+
+ /*
+ * IXON Flag:
+ * Enable XON/XOFF flow control on output.
+ * Transmit XON1, XOFF1
+ */
+ if (termios->c_iflag & IXON)
+ efr |= OMAP_UART_SW_TX;
+
+ /*
+ * IXOFF Flag:
+ * Enable XON/XOFF flow control on input.
+ * Receiver compares XON1, XOFF1.
+ */
+ if (termios->c_iflag & IXOFF)
+ efr |= OMAP_UART_SW_RX;
+
+ serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+
+ up->mcr = serial_in(up, UART_MCR);
+
+ /*
+ * IXANY Flag:
+ * Enable any character to restart output.
+ * Operation resumes after receiving any
+ * character after recognition of the XOFF character
+ */
+ if (termios->c_iflag & IXANY)
+ up->mcr |= UART_MCR_XONANY;
+
+ serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+ serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
+ /* Enable special char function UARTi.EFR_REG[5] and
+ * load the new software flow control mode IXON or IXOFF
+ * and restore the UARTi.EFR_REG[4] ENHANCED_EN value.
+ */
+ serial_out(up, UART_EFR, efr | UART_EFR_SCD);
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+
+ serial_out(up, UART_MCR, up->mcr & ~UART_MCR_TCRTLR);
+ serial_out(up, UART_LCR, up->lcr);
+}
+
+static void
+serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned char cval = 0;
+ unsigned char efr = 0;
+ unsigned long flags = 0;
+ unsigned int baud, quot;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ cval = UART_LCR_WLEN5;
+ break;
+ case CS6:
+ cval = UART_LCR_WLEN6;
+ break;
+ case CS7:
+ cval = UART_LCR_WLEN7;
+ break;
+ default:
+ case CS8:
+ cval = UART_LCR_WLEN8;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ cval |= UART_LCR_STOP;
+ if (termios->c_cflag & PARENB)
+ cval |= UART_LCR_PARITY;
+ if (!(termios->c_cflag & PARODD))
+ cval |= UART_LCR_EPAR;
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
+ quot = serial_omap_get_divisor(port, baud);
+
+ up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
+ UART_FCR_ENABLE_FIFO;
+ if (up->use_dma)
+ up->fcr |= UART_FCR_DMA_SELECT;
+
+ /*
+ * Ok, we're now changing the port state. Do it with
+ * interrupts disabled.
+ */
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+ if (termios->c_iflag & INPCK)
+ up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ up->port.read_status_mask |= UART_LSR_BI;
+
+ /*
+ * Characters to ignore
+ */
+ up->port.ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
+ if (termios->c_iflag & IGNBRK) {
+ up->port.ignore_status_mask |= UART_LSR_BI;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ up->port.ignore_status_mask |= UART_LSR_OE;
+ }
+
+ /*
+ * ignore all characters if CREAD is not set
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ up->port.ignore_status_mask |= UART_LSR_DR;
+
+ /*
+ * Modem status interrupts
+ */
+ up->ier &= ~UART_IER_MSI;
+ if (UART_ENABLE_MS(&up->port, termios->c_cflag))
+ up->ier |= UART_IER_MSI;
+ serial_out(up, UART_IER, up->ier);
+ serial_out(up, UART_LCR, cval); /* reset DLAB */
+
+ /* FIFOs and DMA Settings */
+
+ /* FCR can be changed only when the
+ * baud clock is not running
+ * DLL_REG and DLH_REG set to 0.
+ */
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+ serial_out(up, UART_DLL, 0);
+ serial_out(up, UART_DLM, 0);
+ serial_out(up, UART_LCR, 0);
+
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+
+ up->efr = serial_in(up, UART_EFR);
+ serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
+
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+ up->mcr = serial_in(up, UART_MCR);
+ serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
+ /* FIFO ENABLE, DMA MODE */
+ serial_out(up, UART_FCR, up->fcr);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+
+ if (up->use_dma) {
+ serial_out(up, UART_TI752_TLR, 0);
+ serial_out(up, UART_OMAP_SCR,
+ (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8));
+ }
+
+ serial_out(up, UART_EFR, up->efr);
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+ serial_out(up, UART_MCR, up->mcr);
+
+ /* Protocol, Baud Rate, and Interrupt Settings */
+
+ serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_DISABLE);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+
+ up->efr = serial_in(up, UART_EFR);
+ serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
+
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_IER, 0);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+
+ serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
+ serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
+
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_IER, up->ier);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+
+ serial_out(up, UART_EFR, up->efr);
+ serial_out(up, UART_LCR, cval);
+
+ if (baud > 230400 && baud != 3000000)
+ serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_MODE13X);
+ else
+ serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_MODE16X);
+
+ /* Hardware Flow Control Configuration */
+
+ if (termios->c_cflag & CRTSCTS) {
+ efr |= (UART_EFR_CTS | UART_EFR_RTS);
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+
+ up->mcr = serial_in(up, UART_MCR);
+ serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
+
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+ up->efr = serial_in(up, UART_EFR);
+ serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
+
+ serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
+ serial_out(up, UART_EFR, efr); /* Enable AUTORTS and AUTOCTS */
+ serial_out(up, UART_LCR, UART_LCR_DLAB);
+ serial_out(up, UART_MCR, up->mcr | UART_MCR_RTS);
+ serial_out(up, UART_LCR, cval);
+ }
+
+ serial_omap_set_mctrl(&up->port, up->port.mctrl);
+ /* Software Flow Control Configuration */
+ if (termios->c_iflag & (IXON | IXOFF))
+ serial_omap_configure_xonxoff(up, termios);
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
+ dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->pdev->id);
+}
+
+static void
+serial_omap_pm(struct uart_port *port, unsigned int state,
+ unsigned int oldstate)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+ unsigned char efr;
+
+ dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+ efr = serial_in(up, UART_EFR);
+ serial_out(up, UART_EFR, efr | UART_EFR_ECB);
+ serial_out(up, UART_LCR, 0);
+
+ serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
+ serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+ serial_out(up, UART_EFR, efr);
+ serial_out(up, UART_LCR, 0);
+ /* Enable module level wake up */
+ serial_out(up, UART_OMAP_WER,
+ (state != 0) ? OMAP_UART_WER_MOD_WKUP : 0);
+}
+
+static void serial_omap_release_port(struct uart_port *port)
+{
+ dev_dbg(port->dev, "serial_omap_release_port+\n");
+}
+
+static int serial_omap_request_port(struct uart_port *port)
+{
+ dev_dbg(port->dev, "serial_omap_request_port+\n");
+ return 0;
+}
+
+static void serial_omap_config_port(struct uart_port *port, int flags)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+ dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
+ up->pdev->id);
+ up->port.type = PORT_OMAP;
+}
+
+static int
+serial_omap_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ /* we don't want the core code to modify any port params */
+ dev_dbg(port->dev, "serial_omap_verify_port+\n");
+ return -EINVAL;
+}
+
+static const char *
+serial_omap_type(struct uart_port *port)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+ dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->pdev->id);
+ return up->name;
+}
+
+#ifdef CONFIG_SERIAL_OMAP_CONSOLE
+
+static struct uart_omap_port *serial_omap_console_ports[4];
+
+static struct uart_driver serial_omap_reg;
+
+#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
+static inline void wait_for_xmitr(struct uart_omap_port *up)
+{
+ unsigned int status, tmout = 10000;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ do {
+ status = serial_in(up, UART_LSR);
+
+ if (status & UART_LSR_BI)
+ up->lsr_break_flag = UART_LSR_BI;
+
+ if (--tmout == 0)
+ break;
+ udelay(1);
+ } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
+
+ /* Wait up to 1s for flow control if necessary */
+ if (up->port.flags & UPF_CONS_FLOW) {
+ tmout = 1000000;
+ for (tmout = 1000000; tmout; tmout--) {
+ unsigned int msr = serial_in(up, UART_MSR);
+
+ up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
+ if (msr & UART_MSR_CTS)
+ break;
+
+ udelay(1);
+ }
+ }
+}
+
+static void serial_omap_console_putchar(struct uart_port *port, int ch)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+ wait_for_xmitr(up);
+ serial_out(up, UART_TX, ch);
+}
+
+static void
+serial_omap_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct uart_omap_port *up = serial_omap_console_ports[co->index];
+ unsigned long flags;
+ unsigned int ier;
+ int locked = 1;
+
+ local_irq_save(flags);
+ if (up->port.sysrq)
+ locked = 0;
+ else if (oops_in_progress)
+ locked = spin_trylock(&up->port.lock);
+ else
+ spin_lock(&up->port.lock);
+
+ /*
+ * First save the IER then disable the interrupts
+ */
+ ier = serial_in(up, UART_IER);
+ serial_out(up, UART_IER, 0);
+
+ uart_console_write(&up->port, s, count, serial_omap_console_putchar);
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the IER
+ */
+ wait_for_xmitr(up);
+ serial_out(up, UART_IER, ier);
+ /*
+ * The receive handling will happen properly because the
+ * receive ready bit will still be set; it is not cleared
+ * on read. However, modem control will not, we must
+ * call it if we have saved something in the saved flags
+ * while processing with interrupts off.
+ */
+ if (up->msr_saved_flags)
+ check_modem_status(up);
+
+ if (locked)
+ spin_unlock(&up->port.lock);
+ local_irq_restore(flags);
+}
+
+static int __init
+serial_omap_console_setup(struct console *co, char *options)
+{
+ struct uart_omap_port *up;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (serial_omap_console_ports[co->index] == NULL)
+ return -ENODEV;
+ up = serial_omap_console_ports[co->index];
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(&up->port, co, baud, parity, bits, flow);
+}
+
+static struct console serial_omap_console = {
+ .name = OMAP_SERIAL_NAME,
+ .write = serial_omap_console_write,
+ .device = uart_console_device,
+ .setup = serial_omap_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &serial_omap_reg,
+};
+
+static void serial_omap_add_console_port(struct uart_omap_port *up)
+{
+ serial_omap_console_ports[up->pdev->id] = up;
+}
+
+#define OMAP_CONSOLE (&serial_omap_console)
+
+#else
+
+#define OMAP_CONSOLE NULL
+
+static inline void serial_omap_add_console_port(struct uart_omap_port *up)
+{}
+
+#endif
+
+static struct uart_ops serial_omap_pops = {
+ .tx_empty = serial_omap_tx_empty,
+ .set_mctrl = serial_omap_set_mctrl,
+ .get_mctrl = serial_omap_get_mctrl,
+ .stop_tx = serial_omap_stop_tx,
+ .start_tx = serial_omap_start_tx,
+ .stop_rx = serial_omap_stop_rx,
+ .enable_ms = serial_omap_enable_ms,
+ .break_ctl = serial_omap_break_ctl,
+ .startup = serial_omap_startup,
+ .shutdown = serial_omap_shutdown,
+ .set_termios = serial_omap_set_termios,
+ .pm = serial_omap_pm,
+ .type = serial_omap_type,
+ .release_port = serial_omap_release_port,
+ .request_port = serial_omap_request_port,
+ .config_port = serial_omap_config_port,
+ .verify_port = serial_omap_verify_port,
+};
+
+static struct uart_driver serial_omap_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "OMAP-SERIAL",
+ .dev_name = OMAP_SERIAL_NAME,
+ .nr = OMAP_MAX_HSUART_PORTS,
+ .cons = OMAP_CONSOLE,
+};
+
+static int
+serial_omap_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct uart_omap_port *up = platform_get_drvdata(pdev);
+
+ if (up)
+ uart_suspend_port(&serial_omap_reg, &up->port);
+ return 0;
+}
+
+static int serial_omap_resume(struct platform_device *dev)
+{
+ struct uart_omap_port *up = platform_get_drvdata(dev);
+
+ if (up)
+ uart_resume_port(&serial_omap_reg, &up->port);
+ return 0;
+}
+
+static void serial_omap_rx_timeout(unsigned long uart_no)
+{
+ struct uart_omap_port *up = ui[uart_no];
+ unsigned int curr_dma_pos, curr_transmitted_size;
+ unsigned int ret = 0;
+
+ curr_dma_pos = omap_get_dma_dst_pos(up->uart_dma.rx_dma_channel);
+ if ((curr_dma_pos == up->uart_dma.prev_rx_dma_pos) ||
+ (curr_dma_pos == 0)) {
+ if (jiffies_to_msecs(jiffies - up->port_activity) <
+ RX_TIMEOUT) {
+ mod_timer(&up->uart_dma.rx_timer, jiffies +
+ usecs_to_jiffies(up->uart_dma.rx_timeout));
+ } else {
+ serial_omap_stop_rxdma(up);
+ up->ier |= (UART_IER_RDI | UART_IER_RLSI);
+ serial_out(up, UART_IER, up->ier);
+ }
+ return;
+ }
+
+ curr_transmitted_size = curr_dma_pos -
+ up->uart_dma.prev_rx_dma_pos;
+ up->port.icount.rx += curr_transmitted_size;
+ tty_insert_flip_string(up->port.state->port.tty,
+ up->uart_dma.rx_buf +
+ (up->uart_dma.prev_rx_dma_pos -
+ up->uart_dma.rx_buf_dma_phys),
+ curr_transmitted_size);
+ tty_flip_buffer_push(up->port.state->port.tty);
+ up->uart_dma.prev_rx_dma_pos = curr_dma_pos;
+ if (up->uart_dma.rx_buf_size +
+ up->uart_dma.rx_buf_dma_phys == curr_dma_pos) {
+ ret = serial_omap_start_rxdma(up);
+ if (ret < 0) {
+ serial_omap_stop_rxdma(up);
+ up->ier |= (UART_IER_RDI | UART_IER_RLSI);
+ serial_out(up, UART_IER, up->ier);
+ }
+ } else {
+ mod_timer(&up->uart_dma.rx_timer, jiffies +
+ usecs_to_jiffies(up->uart_dma.rx_timeout));
+ }
+ up->port_activity = jiffies;
+}
+
+static void uart_rx_dma_callback(int lch, u16 ch_status, void *data)
+{
+ return;
+}
+
+static int serial_omap_start_rxdma(struct uart_omap_port *up)
+{
+ int ret = 0;
+
+ if (up->uart_dma.rx_dma_channel == -1) {
+ ret = omap_request_dma(up->uart_dma.uart_dma_rx,
+ "UART Rx DMA",
+ (void *)uart_rx_dma_callback, up,
+ &(up->uart_dma.rx_dma_channel));
+ if (ret < 0)
+ return ret;
+
+ omap_set_dma_src_params(up->uart_dma.rx_dma_channel, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ up->uart_dma.uart_base, 0, 0);
+ omap_set_dma_dest_params(up->uart_dma.rx_dma_channel, 0,
+ OMAP_DMA_AMODE_POST_INC,
+ up->uart_dma.rx_buf_dma_phys, 0, 0);
+ omap_set_dma_transfer_params(up->uart_dma.rx_dma_channel,
+ OMAP_DMA_DATA_TYPE_S8,
+ up->uart_dma.rx_buf_size, 1,
+ OMAP_DMA_SYNC_ELEMENT,
+ up->uart_dma.uart_dma_rx, 0);
+ }
+ up->uart_dma.prev_rx_dma_pos = up->uart_dma.rx_buf_dma_phys;
+ /* FIXME: Cache maintenance needed here? */
+ omap_start_dma(up->uart_dma.rx_dma_channel);
+ mod_timer(&up->uart_dma.rx_timer, jiffies +
+ usecs_to_jiffies(up->uart_dma.rx_timeout));
+ up->uart_dma.rx_dma_used = true;
+ return ret;
+}
+
+static void serial_omap_continue_tx(struct uart_omap_port *up)
+{
+ struct circ_buf *xmit = &up->port.state->xmit;
+ unsigned int start = up->uart_dma.tx_buf_dma_phys
+ + (xmit->tail & (UART_XMIT_SIZE - 1));
+
+ if (uart_circ_empty(xmit))
+ return;
+
+ up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
+ /*
+ * It is a circular buffer. See if the buffer has wounded back.
+ * If yes it will have to be transferred in two separate dma
+ * transfers
+ */
+ if (start + up->uart_dma.tx_buf_size >=
+ up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
+ up->uart_dma.tx_buf_size =
+ (up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE) - start;
+ omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
+ OMAP_DMA_AMODE_CONSTANT,
+ up->uart_dma.uart_base, 0, 0);
+ omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
+ OMAP_DMA_AMODE_POST_INC, start, 0, 0);
+ omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
+ OMAP_DMA_DATA_TYPE_S8,
+ up->uart_dma.tx_buf_size, 1,
+ OMAP_DMA_SYNC_ELEMENT,
+ up->uart_dma.uart_dma_tx, 0);
+ /* FIXME: Cache maintenance needed here? */
+ omap_start_dma(up->uart_dma.tx_dma_channel);
+}
+
+static void uart_tx_dma_callback(int lch, u16 ch_status, void *data)
+{
+ struct uart_omap_port *up = (struct uart_omap_port *)data;
+ struct circ_buf *xmit = &up->port.state->xmit;
+
+ xmit->tail = (xmit->tail + up->uart_dma.tx_buf_size) & \
+ (UART_XMIT_SIZE - 1);
+ up->port.icount.tx += up->uart_dma.tx_buf_size;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&up->port);
+
+ if (uart_circ_empty(xmit)) {
+ spin_lock(&(up->uart_dma.tx_lock));
+ serial_omap_stop_tx(&up->port);
+ up->uart_dma.tx_dma_used = false;
+ spin_unlock(&(up->uart_dma.tx_lock));
+ } else {
+ omap_stop_dma(up->uart_dma.tx_dma_channel);
+ serial_omap_continue_tx(up);
+ }
+ up->port_activity = jiffies;
+ return;
+}
+
+static int serial_omap_probe(struct platform_device *pdev)
+{
+ struct uart_omap_port *up;
+ struct resource *mem, *irq, *dma_tx, *dma_rx;
+ struct omap_uart_port_info *omap_up_info = pdev->dev.platform_data;
+ int ret = -ENOSPC;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(&pdev->dev, "no mem resource?\n");
+ return -ENODEV;
+ }
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!irq) {
+ dev_err(&pdev->dev, "no irq resource?\n");
+ return -ENODEV;
+ }
+
+ if (!request_mem_region(mem->start, (mem->end - mem->start) + 1,
+ pdev->dev.driver->name)) {
+ dev_err(&pdev->dev, "memory region already claimed\n");
+ return -EBUSY;
+ }
+
+ dma_rx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
+ if (!dma_rx) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ dma_tx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
+ if (!dma_tx) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ up = kzalloc(sizeof(*up), GFP_KERNEL);
+ if (up == NULL) {
+ ret = -ENOMEM;
+ goto do_release_region;
+ }
+ sprintf(up->name, "OMAP UART%d", pdev->id);
+ up->pdev = pdev;
+ up->port.dev = &pdev->dev;
+ up->port.type = PORT_OMAP;
+ up->port.iotype = UPIO_MEM;
+ up->port.irq = irq->start;
+
+ up->port.regshift = 2;
+ up->port.fifosize = 64;
+ up->port.ops = &serial_omap_pops;
+ up->port.line = pdev->id;
+
+ up->port.membase = omap_up_info->membase;
+ up->port.mapbase = omap_up_info->mapbase;
+ up->port.flags = omap_up_info->flags;
+ up->port.irqflags = omap_up_info->irqflags;
+ up->port.uartclk = omap_up_info->uartclk;
+ up->uart_dma.uart_base = mem->start;
+
+ if (omap_up_info->dma_enabled) {
+ up->uart_dma.uart_dma_tx = dma_tx->start;
+ up->uart_dma.uart_dma_rx = dma_rx->start;
+ up->use_dma = 1;
+ up->uart_dma.rx_buf_size = 4096;
+ up->uart_dma.rx_timeout = 2;
+ spin_lock_init(&(up->uart_dma.tx_lock));
+ spin_lock_init(&(up->uart_dma.rx_lock));
+ up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
+ up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
+ }
+
+ ui[pdev->id] = up;
+ serial_omap_add_console_port(up);
+
+ ret = uart_add_one_port(&serial_omap_reg, &up->port);
+ if (ret != 0)
+ goto do_release_region;
+
+ platform_set_drvdata(pdev, up);
+ return 0;
+err:
+ dev_err(&pdev->dev, "[UART%d]: failure [%s]: %d\n",
+ pdev->id, __func__, ret);
+do_release_region:
+ release_mem_region(mem->start, (mem->end - mem->start) + 1);
+ return ret;
+}
+
+static int serial_omap_remove(struct platform_device *dev)
+{
+ struct uart_omap_port *up = platform_get_drvdata(dev);
+
+ platform_set_drvdata(dev, NULL);
+ if (up) {
+ uart_remove_one_port(&serial_omap_reg, &up->port);
+ kfree(up);
+ }
+ return 0;
+}
+
+static struct platform_driver serial_omap_driver = {
+ .probe = serial_omap_probe,
+ .remove = serial_omap_remove,
+
+ .suspend = serial_omap_suspend,
+ .resume = serial_omap_resume,
+ .driver = {
+ .name = DRIVER_NAME,
+ },
+};
+
+static int __init serial_omap_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&serial_omap_reg);
+ if (ret != 0)
+ return ret;
+ ret = platform_driver_register(&serial_omap_driver);
+ if (ret != 0)
+ uart_unregister_driver(&serial_omap_reg);
+ return ret;
+}
+
+static void __exit serial_omap_exit(void)
+{
+ platform_driver_unregister(&serial_omap_driver);
+ uart_unregister_driver(&serial_omap_reg);
+}
+
+module_init(serial_omap_init);
+module_exit(serial_omap_exit);
+
+MODULE_DESCRIPTION("OMAP High Speed UART driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Texas Instruments Inc");
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 563e23400913..295e89817de8 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -196,6 +196,9 @@
/* High Speed UART for Medfield */
#define PORT_MFD 95
+/* TI OMAP-UART */
+#define PORT_OMAP 96
+
#ifdef __KERNEL__
#include <linux/compiler.h>