diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
61 files changed, 1931 insertions, 54 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 556c8665fdbf..b78564b2b201 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -23,7 +23,7 @@ Required nodes: range of 0x200 bytes. - syscon: the root node of the Integrator platforms must have a - system controller node pointong to the control registers, + system controller node pointing to the control registers, with the compatible string "arm,integrator-ap-syscon" "arm,integrator-cp-syscon" diff --git a/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt b/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt index 3c436cc4f35d..430608ec09f0 100644 --- a/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt @@ -79,7 +79,9 @@ reboot Required properties - compatible - The string property "brcm,brcmstb-reboot". + The string property "brcm,brcmstb-reboot" for 40nm/28nm chips with + the new SYS_CTRL interface, or "brcm,bcm7038-reboot" for 65nm + chips with the old SUN_TOP_CTRL interface. - syscon A phandle / integer array that points to the syscon node which describes diff --git a/Documentation/devicetree/bindings/arm/fw-cfg.txt b/Documentation/devicetree/bindings/arm/fw-cfg.txt new file mode 100644 index 000000000000..953fb640d9c4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/fw-cfg.txt @@ -0,0 +1,72 @@ +* QEMU Firmware Configuration bindings for ARM + +QEMU's arm-softmmu and aarch64-softmmu emulation / virtualization targets +provide the following Firmware Configuration interface on the "virt" machine +type: + +- A write-only, 16-bit wide selector (or control) register, +- a read-write, 64-bit wide data register. + +QEMU exposes the control and data register to ARM guests as memory mapped +registers; their location is communicated to the guest's UEFI firmware in the +DTB that QEMU places at the bottom of the guest's DRAM. + +The guest writes a selector value (a key) to the selector register, and then +can read the corresponding data (produced by QEMU) via the data register. If +the selected entry is writable, the guest can rewrite it through the data +register. + +The selector register takes keys in big endian byte order. + +The data register allows accesses with 8, 16, 32 and 64-bit width (only at +offset 0 of the register). Accesses larger than a byte are interpreted as +arrays, bundled together only for better performance. The bytes constituting +such a word, in increasing address order, correspond to the bytes that would +have been transferred by byte-wide accesses in chronological order. + +The interface allows guest firmware to download various parameters and blobs +that affect how the firmware works and what tables it installs for the guest +OS. For example, boot order of devices, ACPI tables, SMBIOS tables, kernel and +initrd images for direct kernel booting, virtual machine UUID, SMP information, +virtual NUMA topology, and so on. + +The authoritative registry of the valid selector values and their meanings is +the QEMU source code; the structure of the data blobs corresponding to the +individual key values is also defined in the QEMU source code. + +The presence of the registers can be verified by selecting the "signature" blob +with key 0x0000, and reading four bytes from the data register. The returned +signature is "QEMU". + +The outermost protocol (involving the write / read sequences of the control and +data registers) is expected to be versioned, and/or described by feature bits. +The interface revision / feature bitmap can be retrieved with key 0x0001. The +blob to be read from the data register has size 4, and it is to be interpreted +as a uint32_t value in little endian byte order. The current value +(corresponding to the above outer protocol) is zero. + +The guest kernel is not expected to use these registers (although it is +certainly allowed to); the device tree bindings are documented here because +this is where device tree bindings reside in general. + +Required properties: + +- compatible: "qemu,fw-cfg-mmio". + +- reg: the MMIO region used by the device. + * Bytes 0x0 to 0x7 cover the data register. + * Bytes 0x8 to 0x9 cover the selector register. + * Further registers may be appended to the region in case of future interface + revisions / feature bits. + +Example: + +/ { + #size-cells = <0x2>; + #address-cells = <0x2>; + + fw-cfg@9020000 { + compatible = "qemu,fw-cfg-mmio"; + reg = <0x0 0x9020000 0x0 0xa>; + }; +}; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 4ab09f2202d4..c2340eeeb97f 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -37,9 +37,10 @@ Required properties when using sub-nodes: Sub-nodes required properties: -- reg : the port number -- phys : reference to the SATA PHY node - +- reg : the port number +And at least one of the following properties: +- phys : reference to the SATA PHY node +- target-supply : regulator for SATA target power Examples: sata@ffe08000 { @@ -68,10 +69,12 @@ With sub-nodes: sata0: sata-port@0 { reg = <0>; phys = <&sata_phy 0>; + target-supply = <®_sata0>; }; sata1: sata-port@1 { reg = <1>; phys = <&sata_phy 1>; + target-supply = <®_sata1>;; }; }; diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt new file mode 100644 index 000000000000..b54bf3a2ff57 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt @@ -0,0 +1,110 @@ + +* Samsung Exynos PPMU (Platform Performance Monitoring Unit) device + +The Samsung Exynos SoC has PPMU (Platform Performance Monitoring Unit) for +each IP. PPMU provides the primitive values to get performance data. These +PPMU events provide information of the SoC's behaviors so that you may +use to analyze system performance, to make behaviors visible and to count +usages of each IP (DMC, CPU, RIGHTBUS, LEFTBUS, CAM interface, LCD, G3D, MFC). +The Exynos PPMU driver uses the devfreq-event class to provide event data +to various devfreq devices. The devfreq devices would use the event data when +derterming the current state of each IP. + +Required properties: +- compatible: Should be "samsung,exynos-ppmu". +- reg: physical base address of each PPMU and length of memory mapped region. + +Optional properties: +- clock-names : the name of clock used by the PPMU, "ppmu" +- clocks : phandles for clock specified in "clock-names" property +- #clock-cells: should be 1. + +Example1 : PPMU nodes in exynos3250.dtsi are listed below. + + ppmu_dmc0: ppmu_dmc0@106a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106a0000 0x2000>; + status = "disabled"; + }; + + ppmu_dmc1: ppmu_dmc1@106b0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106b0000 0x2000>; + status = "disabled"; + }; + + ppmu_cpu: ppmu_cpu@106c0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106c0000 0x2000>; + status = "disabled"; + }; + + ppmu_rightbus: ppmu_rightbus@112a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x112a0000 0x2000>; + clocks = <&cmu CLK_PPMURIGHT>; + clock-names = "ppmu"; + status = "disabled"; + }; + + ppmu_leftbus: ppmu_leftbus0@116a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x116a0000 0x2000>; + clocks = <&cmu CLK_PPMULEFT>; + clock-names = "ppmu"; + status = "disabled"; + }; + +Example2 : Events of each PPMU node in exynos3250-rinato.dts are listed below. + + &ppmu_dmc0 { + status = "okay"; + + events { + ppmu_dmc0_3: ppmu-event3-dmc0 { + event-name = "ppmu-event3-dmc0"; + }; + + ppmu_dmc0_2: ppmu-event2-dmc0 { + event-name = "ppmu-event2-dmc0"; + }; + + ppmu_dmc0_1: ppmu-event1-dmc0 { + event-name = "ppmu-event1-dmc0"; + }; + + ppmu_dmc0_0: ppmu-event0-dmc0 { + event-name = "ppmu-event0-dmc0"; + }; + }; + }; + + &ppmu_dmc1 { + status = "okay"; + + events { + ppmu_dmc1_3: ppmu-event3-dmc1 { + event-name = "ppmu-event3-dmc1"; + }; + }; + }; + + &ppmu_leftbus { + status = "okay"; + + events { + ppmu_leftbus_3: ppmu-event3-leftbus { + event-name = "ppmu-event3-leftbus"; + }; + }; + }; + + &ppmu_rightbus { + status = "okay"; + + events { + ppmu_rightbus_3: ppmu-event3-rightbus { + event-name = "ppmu-event3-rightbus"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/graph.txt b/Documentation/devicetree/bindings/graph.txt index 1a69c078adf2..fcb1c6a4787b 100644 --- a/Documentation/devicetree/bindings/graph.txt +++ b/Documentation/devicetree/bindings/graph.txt @@ -19,7 +19,7 @@ type of the connections, they just map their existence. Specific properties may be described by specialized bindings depending on the type of connection. To see how this binding applies to video pipelines, for example, see -Documentation/device-tree/bindings/media/video-interfaces.txt. +Documentation/devicetree/bindings/media/video-interfaces.txt. Here the ports describe data interfaces, and the links between them are the connecting data buses. A single port with multiple connections can correspond to multiple devices being connected to the same physical bus. diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt index 437e0db3823c..4c26fda3844a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-st.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -31,7 +31,7 @@ i2c0: i2c@fed40000 { compatible = "st,comms-ssc4-i2c"; reg = <0xfed40000 0x110>; interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&CLK_S_ICN_REG_0>; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; clock-names = "ssc"; clock-frequency = <400000>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 9f4e3824e71e..9f41d05be3be 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -47,6 +47,7 @@ dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support +dlg,da9063 DA9063: system PMIC for quad-core application processors epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer diff --git a/Documentation/devicetree/bindings/input/e3x0-button.txt b/Documentation/devicetree/bindings/input/e3x0-button.txt new file mode 100644 index 000000000000..751665e8e47a --- /dev/null +++ b/Documentation/devicetree/bindings/input/e3x0-button.txt @@ -0,0 +1,25 @@ +National Instruments Ettus Research USRP E3x0 button driver + +This module is part of the NI Ettus Research USRP E3x0 SDR. + +This module provides a simple power button event via two interrupts. + +Required properties: +- compatible: should be one of the following + - "ettus,e3x0-button": For devices such as the NI Ettus Research USRP E3x0 +- interrupt-parent: + - a phandle to the interrupt controller that it is attached to. +- interrupts: should be one of the following + - <0 30 1>, <0 31 1>: For devices such as the NI Ettus Research USRP E3x0 +- interrupt-names: should be one of the following + - "press", "release": For devices such as the NI Ettus Research USRP E3x0 + +Note: Interrupt numbers might vary depending on the FPGA configuration. + +Example: + button { + compatible = "ettus,e3x0-button"; + interrupt-parent = <&intc>; + interrupts = <0 30 1>, <0 31 1>; + interrupt-names = "press", "release"; + } diff --git a/Documentation/devicetree/bindings/input/regulator-haptic.txt b/Documentation/devicetree/bindings/input/regulator-haptic.txt new file mode 100644 index 000000000000..3ed1c7eb2f97 --- /dev/null +++ b/Documentation/devicetree/bindings/input/regulator-haptic.txt @@ -0,0 +1,21 @@ +* Regulator Haptic Device Tree Bindings + +Required Properties: + - compatible : Should be "regulator-haptic" + - haptic-supply : Power supply to the haptic motor. + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + + - max-microvolt : The maximum voltage value supplied to the haptic motor. + [The unit of the voltage is a micro] + + - min-microvolt : The minimum voltage value supplied to the haptic motor. + [The unit of the voltage is a micro] + +Example: + + haptics { + compatible = "regulator-haptic"; + haptic-supply = <&motor_regulator>; + max-microvolt = <2700000>; + min-microvolt = <1100000>; + }; diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt new file mode 100644 index 000000000000..b9c32f6fd687 --- /dev/null +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -0,0 +1,62 @@ +Allwinner sun4i low res adc attached tablet keys +------------------------------------------------ + +Required properties: + - compatible: "allwinner,sun4i-a10-lradc-keys" + - reg: mmio address range of the chip + - interrupts: interrupt to which the chip is connected + - vref-supply: powersupply for the lradc reference voltage + +Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys": + +Required subnode-properties: + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + - channel: Channel this key is attached to, mut be 0 or 1. + - voltage: Voltage in µV at lradc input when this key is pressed. + +Example: + +#include <dt-bindings/input/input.h> + + lradc: lradc@01c22800 { + compatible = "allwinner,sun4i-a10-lradc-keys"; + reg = <0x01c22800 0x100>; + interrupts = <31>; + vref-supply = <®_vcc3v0>; + + button@191 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <191274>; + }; + + button@392 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <392644>; + }; + + button@601 { + label = "Menu"; + linux,code = <KEY_MENU>; + channel = <0>; + voltage = <601151>; + }; + + button@795 { + label = "Enter"; + linux,code = <KEY_ENTER>; + channel = <0>; + voltage = <795090>; + }; + + button@987 { + label = "Home"; + linux,code = <KEY_HOMEPAGE>; + channel = <0>; + voltage = <987387>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt index aef57791f40b..433332d3b2ba 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt @@ -2,9 +2,10 @@ sun4i resistive touchscreen controller -------------------------------------- Required properties: - - compatible: "allwinner,sun4i-a10-ts" + - compatible: "allwinner,sun4i-a10-ts" or "allwinner,sun6i-a31-ts" - reg: mmio address range of the chip - interrupts: interrupt to which the chip is connected + - #thermal-sensor-cells: shall be 0 Optional properties: - allwinner,ts-attached: boolean indicating that an actual touchscreen is @@ -17,4 +18,5 @@ Example: reg = <0x01c25000 0x100>; interrupts = <29>; allwinner,ts-attached; + #thermal-sensor-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt index 878549ba814d..6c4fb34823d3 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -28,6 +28,20 @@ Required properties: ti,adc-channels: List of analog inputs available for ADC. AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. +Optional properties: +- child "tsc" + ti,charge-delay: Length of touch screen charge delay step in terms of + ADC clock cycles. Charge delay value should be large + in order to avoid false pen-up events. This value + effects the overall sampling speed, hence need to be + kept as low as possible, while avoiding false pen-up + event. Start from a lower value, say 0x400, and + increase value until false pen-up events are avoided. + The pen-up detection happens immediately after the + charge step, so this does in fact function as a + hardware knob for adjusting the amount of "settling + time". + Example: tscadc: tscadc@44e0d000 { compatible = "ti,am3359-tscadc"; @@ -36,6 +50,7 @@ Example: ti,x-plate-resistance = <200>; ti,coordiante-readouts = <5>; ti,wire-config = <0x00 0x11 0x22 0x33>; + ti,charge-delay = <0x400>; }; adc { diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt new file mode 100644 index 000000000000..e30e0b93f2b3 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -0,0 +1,17 @@ +Texas Instruments TPS65218 power button + +This driver provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be "ti,tps65218-pwrbutton" +- interrupts: should be one of the following + - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 + +Example: + +&tps { + power-button { + compatible = "ti,tps65218-pwrbutton"; + interrupts = <3 IRQ_TYPE_EDGE_BOTH>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt new file mode 100644 index 000000000000..855e1faf73e2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -0,0 +1,63 @@ +SMIA/SMIA++ sensor + +SMIA (Standard Mobile Imaging Architecture) is an image sensor standard +defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension +of that. These definitions are valid for both types of sensors. + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "nokia,smia" +- reg: I2C address (0x10, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor + dependent). +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor +- link-frequencies: List of allowed data link frequencies. An array of + 64-bit elements. + + +Optional properties +------------------- + +- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, + the NVM contents will not be read. +- reset-gpios: XSHUTDOWN GPIO + + +Endpoint node mandatory properties +---------------------------------- + +- clock-lanes: <0> +- data-lanes: <1..n> +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c2 { + clock-frequency = <400000>; + + smiapp_1: camera@10 { + compatible = "nokia,smia"; + reg = <0x10>; + reset-gpios = <&gpio3 20 0>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <512>; /* 8 * 64 */ + link-frequencies = /bits/ 64 <199200000 210000000 499200000>; + port { + smiapp_1_1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt index 23dd5ad07b7c..1811a067c72c 100644 --- a/Documentation/devicetree/bindings/media/sunxi-ir.txt +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -1,7 +1,7 @@ Device-Tree bindings for SUNXI IR controller found in sunXi SoC family Required properties: -- compatible : should be "allwinner,sun4i-a10-ir"; +- compatible : "allwinner,sun4i-a10-ir" or "allwinner,sun5i-a13-ir" - clocks : list of clock specifiers, corresponding to entries in clock-names property; - clock-names : should contain "apb" and "ir" entries; @@ -10,6 +10,7 @@ Required properties: Optional properties: - linux,rc-map-name : Remote control map name. +- resets : phandle + reset specifier pair Example: @@ -17,6 +18,7 @@ ir0: ir@01c21800 { compatible = "allwinner,sun4i-a10-ir"; clocks = <&apb0_gates 6>, <&ir0_clk>; clock-names = "apb", "ir"; + resets = <&apb0_rst 1>; interrupts = <0 5 1>; reg = <0x01C21800 0x40>; linux,rc-map-name = "rc-rc6-mce"; diff --git a/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt new file mode 100644 index 000000000000..3932e766553a --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt @@ -0,0 +1,61 @@ +Texas Instruments AM437x CAMERA (VPFE) +-------------------------------------- + +The Video Processing Front End (VPFE) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect RAW image-sensor modules and video decoders +to the AM437x device. + +Required properties: +- compatible: must be "ti,am437x-vpfe" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPFE; +- ti,am437x-vpfe-interface: can be one of the following, + 0 - Raw Bayer Interface. + 1 - 8 Bit BT656 Interface. + 2 - 10 Bit BT656 Interface. + 3 - YCbCr 8 Bit Interface. + 4 - YCbCr 16 Bit Interface. + +VPFE supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + vpfe: vpfe@f0034000 { + compatible = "ti,am437x-vpfe"; + reg = <0x48328000 0x2000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&vpfe_pins_default>; + pinctrl-1 = <&vpfe_pins_sleep>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vpfe0_ep: endpoint { + remote-endpoint = <&ov2659_1>; + ti,am437x-vpfe-interface = <0>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; + + i2c1: i2c@4802a000 { + + ov2659@30 { + compatible = "ti,ov2659"; + reg = <0x30>; + + port { + ov2659_1: endpoint { + remote-endpoint = <&vpfe0_ep>; + bus-width = <8>; + mclk-frequency = <12000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index ce719f89dd1c..52a14cf099ac 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -103,6 +103,9 @@ Optional endpoint properties array contains only one entry. - clock-noncontinuous: a boolean property to allow MIPI CSI-2 non-continuous clock mode. +- link-frequencies: Allowed data bus frequencies. For MIPI CSI-2, for + instance, this is the actual frequency of the bus, not bits per clock per + lane value. An array of 64-bit unsigned integers. Example diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 75fdfaf41831..e39f0bc1f55e 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -39,6 +39,12 @@ to get matched with their hardware counterparts as follow: -BUCKn : 1-4. Use standard regulator bindings for it ('regulator-off-in-suspend'). + LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable + control. To turn this feature on this property must be added to the regulator + sub-node: + - maxim,ena-gpios : one GPIO specifier enable control (the gpio + flags are actually ignored and always + ACTIVE_HIGH is used) Example: @@ -65,4 +71,12 @@ Example: regulator-always-on; regulator-boot-on; }; + + buck9_reg { + regulator-compatible = "BUCK9"; + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; + }; } diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 01e9f30fe678..38e64405e98d 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -41,6 +41,41 @@ Optional properties: To get more informations, please refer to documentaion. [*] refer Documentation/devicetree/bindings/pwm/pwm.txt +- charger : Node configuring the charger driver. + If present, required properties: + - compatible : Must be "maxim,max77693-charger". + + Optional properties (if not set, defaults will be used): + - maxim,constant-microvolt : Battery constant voltage in uV. The charger + will operate in fast charge constant current mode till battery voltage + reaches this level. Then the charger will switch to fast charge constant + voltage mode. Also vsys (system voltage) will be set to this value when + DC power is supplied but charger is not enabled. + Valid values: 3650000 - 4400000, step by 25000 (rounded down) + Default: 4200000 + + - maxim,min-system-microvolt : Minimal system voltage in uV. + Valid values: 3000000 - 3700000, step by 100000 (rounded down) + Default: 3600000 + + - maxim,thermal-regulation-celsius : Temperature in Celsius for entering + high temperature charging mode. If die temperature exceeds this value + the charging current will be reduced by 105 mA/Celsius. + Valid values: 70, 85, 100, 115 + Default: 100 + + - maxim,battery-overcurrent-microamp : Overcurrent protection threshold + in uA (current from battery to system). + Valid values: 2000000 - 3500000, step by 250000 (rounded down) + Default: 3500000 + + - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for + triggering input voltage regulation loop. If input voltage decreases + below this value, the input current will be reduced to reach the + threshold voltage. + Valid values: 4300000, 4700000, 4800000, 4900000 + Default: 4300000 + Example: max77693@66 { compatible = "maxim,max77693"; @@ -73,4 +108,14 @@ Example: pwms = <&pwm 0 40000 0>; pwm-names = "haptic"; }; + + charger { + compatible = "maxim,max77693-charger"; + + maxim,constant-microvolt = <4200000>; + maxim,min-system-microvolt = <3600000>; + maxim,thermal-regulation-celsius = <75>; + maxim,battery-overcurrent-microamp = <3000000>; + maxim,charge-input-threshold-microvolt = <4300000>; + }; }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt index 42409bfe04c4..33df3932168e 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -7,17 +7,38 @@ Required properties: - SerDes Rx/Tx registers - SerDes integration registers (1/2) - SerDes integration registers (2/2) +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the amd-xgbe-phy interrupt. Optional properties: - amd,speed-set: Speed capabilities of the device 0 - 1GbE and 10GbE (default) 1 - 2.5GbE and 10GbE +The following optional properties are represented by an array with each +value corresponding to a particular speed. The first array value represents +the setting for the 1GbE speed, the second value for the 2.5GbE speed and +the third value for the 10GbE speed. All three values are required if the +property is used. +- amd,serdes-blwc: Baseline wandering correction enablement + 0 - Off + 1 - On +- amd,serdes-cdr-rate: CDR rate speed selection +- amd,serdes-pq-skew: PQ (data sampling) skew +- amd,serdes-tx-amp: TX amplitude boost + Example: xgbe_phy@e1240800 { compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45"; reg = <0 0xe1240800 0 0x00400>, <0 0xe1250000 0 0x00060>, <0 0xe1250080 0 0x00004>; + interrupt-parent = <&gic>; + interrupts = <0 323 4>; amd,speed-set = <0>; + amd,serdes-blwc = <1>, <1>, <0>; + amd,serdes-cdr-rate = <2>, <2>, <7>; + amd,serdes-pq-skew = <10>, <10>, <30>; + amd,serdes-tx-amp = <15>, <15>, <10>; }; diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt index 28767ed7c1bd..5224bf05f6f8 100644 --- a/Documentation/devicetree/bindings/net/davicom-dm9000.txt +++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt @@ -11,6 +11,8 @@ Required properties: Optional properties: - davicom,no-eeprom : Configuration EEPROM is not available - davicom,ext-phy : Use external PHY +- reset-gpios : phandle of gpio that will be used to reset chip during probe +- vcc-supply : phandle of regulator that will be used to enable power to chip Example: @@ -21,4 +23,6 @@ Example: interrupts = <7 4>; local-mac-address = [00 00 de ad be ef]; davicom,no-eeprom; + reset-gpios = <&gpf 12 GPIO_ACTIVE_LOW>; + vcc-supply = <ð0_power>; }; diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt index 032808843f90..24c5cdaba8d2 100644 --- a/Documentation/devicetree/bindings/net/davinci_emac.txt +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -4,7 +4,8 @@ This file provides information, what the device node for the davinci_emac interface contains. Required properties: -- compatible: "ti,davinci-dm6467-emac" or "ti,am3517-emac" +- compatible: "ti,davinci-dm6467-emac", "ti,am3517-emac" or + "ti,dm816-emac" - reg: Offset and length of the register set for the device - ti,davinci-ctrl-reg-offset: offset to control register - ti,davinci-ctrl-mod-reg-offset: offset to control module register diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 0c8775c45798..a9eb611bee68 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -22,6 +22,8 @@ Optional properties: - fsl,num-rx-queues : The property is valid for enet-avb IP, which supports hw multi queues. Should specify the rx queue number, otherwise set rx queue number to 1. +- fsl,magic-packet : If present, indicates that the hardware supports waking + up via magic packet. Optional subnodes: - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index be6ea8960f20..1e97532a0b79 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -8,7 +8,16 @@ of how to define a PHY. Required properties: - reg : Offset and length of the register set for the device - compatible : Should define the compatible device type for the - mdio. Currently, this is most likely to be "fsl,gianfar-mdio" + mdio. Currently supported strings/devices are: + - "fsl,gianfar-tbi" + - "fsl,gianfar-mdio" + - "fsl,etsec2-tbi" + - "fsl,etsec2-mdio" + - "fsl,ucc-mdio" + - "fsl,fman-mdio" + When device_type is "mdio", the following strings are also considered: + - "gianfar" + - "ucc_geth_phy" Example: diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt new file mode 100644 index 000000000000..988fc694b663 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt @@ -0,0 +1,88 @@ +Hisilicon hip04 Ethernet Controller + +* Ethernet controller node + +Required properties: +- compatible: should be "hisilicon,hip04-mac". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- port-handle: <phandle port channel> + phandle, specifies a reference to the syscon ppe node + port, port number connected to the controller + channel, recv channel start from channel * number (RX_DESC_NUM) +- phy-mode: see ethernet.txt [1]. + +Optional properties: +- phy-handle: see ethernet.txt [1]. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + + +* Ethernet ppe node: +Control rx & tx fifos of all ethernet controllers. +Have 2048 recv channels shared by all ethernet controllers, only if no overlap. +Each controller's recv channel start from channel * number (RX_DESC_NUM). + +Required properties: +- compatible: "hisilicon,hip04-ppe", "syscon". +- reg: address and length of the register set for the device. + + +* MDIO bus node: + +Required properties: + +- compatible: should be "hisilicon,hip04-mdio". +- Inherits from MDIO bus node binding [2] +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + mdio { + compatible = "hisilicon,hip04-mdio"; + reg = <0x28f1000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + }; + + ppe: ppe@28c0000 { + compatible = "hisilicon,hip04-ppe", "syscon"; + reg = <0x28c0000 0x10000>; + }; + + fe: ethernet@28b0000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x28b0000 0x10000>; + interrupts = <0 413 4>; + phy-mode = "mii"; + port-handle = <&ppe 31 0>; + }; + + ge0: ethernet@2800000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2800000 0x10000>; + interrupts = <0 402 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 0 1>; + phy-handle = <&phy0>; + }; + + ge8: ethernet@2880000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2880000 0x10000>; + interrupts = <0 410 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 8 2>; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt new file mode 100644 index 000000000000..f9c07710478d --- /dev/null +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -0,0 +1,197 @@ +This document describes the device tree bindings associated with the +keystone network coprocessor(NetCP) driver support. + +The network coprocessor (NetCP) is a hardware accelerator that processes +Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsytem with a ethernet +switch sub-module to send and receive packets. NetCP also includes a packet +accelerator (PA) module to perform packet classification operations such as +header matching, and packet modification operations such as checksum +generation. NetCP can also optionally include a Security Accelerator (SA) +capable of performing IPSec operations on ingress/egress packets. + +Keystone II SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which +includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates +per Ethernet port. + +Keystone NetCP driver has a plug-in module architecture where each of the NetCP +sub-modules exist as a loadable kernel module which plug in to the netcp core. +These sub-modules are represented as "netcp-devices" in the dts bindings. It is +mandatory to have the ethernet switch sub-module for the ethernet interface to +be operational. Any other sub-module like the PA is optional. + +NetCP Ethernet SubSystem Layout: + +----------------------------- + NetCP subsystem(10G or 1G) +----------------------------- + | + |-> NetCP Devices -> | + | |-> GBE/XGBE Switch + | | + | |-> Packet Accelerator + | | + | |-> Security Accelerator + | + | + | + |-> NetCP Interfaces -> | + |-> Ethernet Port 0 + | + |-> Ethernet Port 1 + | + |-> Ethernet Port 2 + | + |-> Ethernet Port 3 + + +NetCP subsystem properties: +Required properties: +- compatible: Should be "ti,netcp-1.0" +- clocks: phandle to the reference clocks for the subsystem. +- dma-id: Navigator packet dma instance id. + +Optional properties: +- reg: register location and the size for the following register + regions in the specified order. + - Efuse MAC address register +- dma-coherent: Present if dma operations are coherent +- big-endian: Keystone devices can be operated in a mode where the DSP is in + the big endian mode. In such cases enable this option. This + option should also be enabled if the ARM is operated in + big endian mode with the DSP in little endian. + +NetCP device properties: Device specification for NetCP sub-modules. +1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications. +Required properties: +- label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb. +- reg: register location and the size for the following register + regions in the specified order. + - subsystem registers + - serdes registers +- tx-channel: the navigator packet dma channel name for tx. +- tx-queue: the navigator queue number associated with the tx dma channel. +- interfaces: specification for each of the switch port to be registered as a + network interface in the stack. +-- slave-port: Switch port number, 0 based numbering. +-- link-interface: type of link interface, supported options are + - mac<->mac auto negotiate mode: 0 + - mac<->phy mode: 1 + - mac<->mac forced mode: 2 + - mac<->fiber mode: 3 + - mac<->phy mode with no mdio: 4 + - 10Gb mac<->phy mode : 10 + - 10Gb mac<->mac forced mode : 11 +----phy-handle: phandle to PHY device + +Optional properties: +- enable-ale: NetCP driver keeps the address learning feature in the ethernet + switch module disabled. This attribute is to enable the address + learning. +- secondary-slave-ports: specification for each of the switch port not be + registered as a network interface. NetCP driver + will only initialize these ports and attach PHY + driver to them if needed. + +NetCP interface properties: Interface specification for NetCP sub-modules. +Required properties: +- rx-channel: the navigator packet dma channel name for rx. +- rx-queue: the navigator queue number associated with rx dma channel. +- rx-pool: specifies the number of descriptors to be used & the region-id + for creating the rx descriptor pool. +- tx-pool: specifies the number of descriptors to be used & the region-id + for creating the tx descriptor pool. +- rx-queue-depth: number of descriptors in each of the free descriptor + queue (FDQ) for the pktdma Rx flow. There can be at + present a maximum of 4 queues per Rx flow. +- rx-buffer-size: the buffer size for each of the Rx flow FDQ. +- tx-completion-queue: the navigator queue number where the descriptors are + recycled after Tx DMA completion. + +Optional properties: +- efuse-mac: If this is 1, then the MAC address for the interface is + obtained from the device efuse mac address register +- local-mac-address: the driver is designed to use the of_get_mac_address api + only if efuse-mac is 0. When efuse-mac is 0, the MAC + address is obtained from local-mac-address. If this + attribute is not present, then the driver will use a + random MAC address. +- "netcp-device label": phandle to the device specification for each of NetCP + sub-module attached to this interface. + +Example binding: + +netcp: netcp@2090000 { + reg = <0x2620110 0x8>; + reg-names = "efuse"; + compatible = "ti,netcp-1.0"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>; + dma-coherent; + /* big-endian; */ + dma-id = <0>; + + netcp-devices { + #address-cells = <1>; + #size-cells = <1>; + ranges; + gbe@0x2090000 { + label = "netcp-gbe"; + reg = <0x2090000 0xf00>; + /* enable-ale; */ + tx-queue = <648>; + tx-channel = <8>; + + interfaces { + gbe0: interface-0 { + slave-port = <0>; + link-interface = <4>; + }; + gbe1: interface-1 { + slave-port = <1>; + link-interface = <4>; + }; + }; + + secondary-slave-ports { + port-2 { + slave-port = <2>; + link-interface = <2>; + }; + port-3 { + slave-port = <3>; + link-interface = <2>; + }; + }; + }; + }; + + netcp-interfaces { + interface-0 { + rx-channel = <22>; + rx-pool = <1024 12>; + tx-pool = <1024 12>; + rx-queue-depth = <128 128 0 0>; + rx-buffer-size = <1518 4096 0 0>; + rx-queue = <8704>; + tx-completion-queue = <8706>; + efuse-mac = <1>; + netcp-gbe = <&gbe0>; + + }; + interface-1 { + rx-channel = <23>; + rx-pool = <1024 12>; + tx-pool = <1024 12>; + rx-queue-depth = <128 128 0 0>; + rx-buffer-size = <1518 4096 0 0>; + rx-queue = <8705>; + tx-completion-queue = <8707>; + efuse-mac = <0>; + local-mac-address = [02 18 31 7e 3e 6f]; + netcp-gbe = <&gbe1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt index e4faa2e8dfeb..7bb2e213d6f9 100644 --- a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt +++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt @@ -1,7 +1,7 @@ * STMicroelectronics SAS. ST21NFCA NFC Controller Required properties: -- compatible: Should be "st,st21nfca_i2c". +- compatible: Should be "st,st21nfca-i2c". - clock-frequency: I²C work frequency. - reg: address on the bus - interrupt-parent: phandle for the interrupt gpio controller @@ -11,6 +11,10 @@ Required properties: Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): @@ -20,7 +24,7 @@ Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): st21nfca: st21nfca@1 { - compatible = "st,st21nfca_i2c"; + compatible = "st,st21nfca-i2c"; reg = <0x01>; clock-frequency = <400000>; @@ -29,5 +33,8 @@ Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): interrupts = <2 IRQ_TYPE_LEVEL_LOW>; enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; }; }; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt index 9005608cbbd1..bb237072dbe9 100644 --- a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt +++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt @@ -1,7 +1,7 @@ * STMicroelectronics SAS. ST21NFCB NFC Controller Required properties: -- compatible: Should be "st,st21nfcb_i2c". +- compatible: Should be "st,st21nfcb-i2c". - clock-frequency: I²C work frequency. - reg: address on the bus - interrupt-parent: phandle for the interrupt gpio controller @@ -20,7 +20,7 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): st21nfcb: st21nfcb@8 { - compatible = "st,st21nfcb_i2c"; + compatible = "st,st21nfcb-i2c"; reg = <0x08>; clock-frequency = <400000>; diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt new file mode 100644 index 000000000000..21fd199e89b5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -0,0 +1,68 @@ +Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) + +The device node has following properties. + +Required properties: + - compatible: Can be "rockchip,rk3288-gmac". + - reg: addresses and length of the register sets for the device. + - interrupts: Should contain the GMAC interrupts. + - interrupt-names: Should contain the interrupt names "macirq". + - rockchip,grf: phandle to the syscon grf used to control speed and mode. + - clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY. + <&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC + <&cru SCLK_MAC_RX>: clock gate for RX + <&cru SCLK_MAC_TX>: clock gate for TX + <&cru SCLK_MACREF>: clock gate for RMII referce clock + <&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output + <&cru ACLK_GMAC>: AXI clock gate for GMAC + <&cru PCLK_GMAC>: APB clock gate for GMAC + - clock-names: One name for each entry in the clocks property. + - phy-mode: See ethernet.txt file in the same directory. + - pinctrl-names: Names corresponding to the numbered pinctrl states. + - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>. + - clock_in_out: For RGMII, it must be "input", means main clock(125MHz) + is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means + PHY provides the reference clock(50MHz), "output" means GMAC provides the + reference clock. + - snps,reset-gpio gpio number for phy reset. + - snps,reset-active-low boolean flag to indicate if phy reset is active low. + - assigned-clocks: main clock, should be <&cru SCLK_MAC>; + - assigned-clock-parents = parent of main clock. + can be <&ext_gmac> or <&cru SCLK_MAC_PLL>. + +Optional properties: + - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default. + - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default. + - phy-supply: phandle to a regulator if the PHY needs one + +Example: + +gmac: ethernet@ff290000 { + compatible = "rockchip,rk3288-gmac"; + reg = <0xff290000 0x10000>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + rockchip,grf = <&grf>; + clocks = <&cru SCLK_MAC>, + <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>, + <&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>, + <&cru ACLK_GMAC>, <&cru PCLK_GMAC>; + clock-names = "stmmaceth", + "mac_clk_rx", "mac_clk_tx", + "clk_mac_ref", "clk_mac_refout", + "aclk_mac", "pclk_mac"; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>; + + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + tx_delay = <0x30>; + rx_delay = <0x10>; + + status = "ok"; +}; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt index 6762a6b5da7e..d05c1e1fd9b6 100644 --- a/Documentation/devicetree/bindings/net/sti-dwmac.txt +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -9,14 +9,10 @@ The device node has following properties. Required properties: - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac", "st,stih407-dwmac", "st,stid127-dwmac". - - reg : Offset of the glue configuration register map in system - configuration regmap pointed by st,syscon property and size. - - st,syscon : Should be phandle to system configuration node which - encompases this glue registers. + - st,syscon : Should be phandle/offset pair. The phandle to the syscon node which + encompases the glue register, and the offset of the control register. - st,gmac_en: this is to enable the gmac into a dedicated sysctl control register available on STiH407 SoC. - - sti-ethconf: this is the gmac glue logic register to enable the GMAC, - select among the different modes and program the clk retiming. - pinctrl-0: pin-control for all the MII mode supported. Optional properties: @@ -40,10 +36,10 @@ ethernet0: dwmac@9630000 { device_type = "network"; status = "disabled"; compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; - reg = <0x9630000 0x8000>, <0x80 0x4>; - reg-names = "stmmaceth", "sti-ethconf"; + reg = <0x9630000 0x8000>; + reg-names = "stmmaceth"; - st,syscon = <&syscfg_sbc_reg>; + st,syscon = <&syscfg_sbc_reg 0x80>; st,gmac_en; resets = <&softreset STIH407_ETH1_SOFTRESET>; reset-names = "stmmaceth"; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index c41afd963edf..8ca65cec52ae 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -43,6 +43,7 @@ Optional properties: available this clock is used for programming the Timestamp Addend Register. If not passed then the system clock will be used and this is fine on some platforms. +- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. Examples: diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt new file mode 100644 index 000000000000..edefc26c6204 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -0,0 +1,30 @@ +* Qualcomm Atheros ath10k wireless devices + +For ath10k devices the calibration data can be provided through Device +Tree. The node is a child node of the PCI controller. + +Required properties: +-compatible : Should be "qcom,ath10k" + +Optional properties: +- qcom,ath10k-calibration-data : calibration data as an array, the + length can vary between hw versions + + +Example: + +pci { + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + reg = <0 0 0 0 0>; + device_type = "pci"; + qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/versatile.txt b/Documentation/devicetree/bindings/pci/versatile.txt new file mode 100644 index 000000000000..ebd1e7d0403e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/versatile.txt @@ -0,0 +1,59 @@ +* ARM Versatile Platform Baseboard PCI interface + +PCI host controller found on the ARM Versatile PB board's FPGA. + +Required properties: +- compatible: should contain "arm,versatile-pci" to identify the Versatile PCI + controller. +- reg: base addresses and lengths of the pci controller. There must be 3 + entries: + - Versatile-specific registers + - Self Config space + - Config space +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- bus-range: set to <0 0xff> +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties to define + the mapping of the PCI interface to interrupt numbers. + +Example: + +pci-controller@10001000 { + compatible = "arm,versatile-pci"; + device_type = "pci"; + reg = <0x10001000 0x1000 + 0x41000000 0x10000 + 0x42000000 0x100000>; + bus-range = <0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + ranges = <0x01000000 0 0x00000000 0x43000000 0 0x00010000 /* downstream I/O */ + 0x02000000 0 0x50000000 0x50000000 0 0x10000000 /* non-prefetchable memory */ + 0x42000000 0 0x60000000 0x60000000 0 0x10000000>; /* prefetchable memory */ + + interrupt-map-mask = <0x1800 0 0 7>; + interrupt-map = <0x1800 0 0 1 &sic 28 + 0x1800 0 0 2 &sic 29 + 0x1800 0 0 3 &sic 30 + 0x1800 0 0 4 &sic 27 + + 0x1000 0 0 1 &sic 27 + 0x1000 0 0 2 &sic 28 + 0x1000 0 0 3 &sic 29 + 0x1000 0 0 4 &sic 30 + + 0x0800 0 0 1 &sic 30 + 0x0800 0 0 2 &sic 27 + 0x0800 0 0 3 &sic 28 + 0x0800 0 0 4 &sic 29 + + 0x0000 0 0 1 &sic 29 + 0x0000 0 0 2 &sic 30 + 0x0000 0 0 3 &sic 27 + 0x0000 0 0 4 &sic 28>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt index 42c880886cf7..9802d5d911aa 100644 --- a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt @@ -6,8 +6,10 @@ for SATA and PCIe. Required properties (controller (parent) node): - compatible : Should be "st,miphy365x-phy" -- st,syscfg : Should be a phandle of the system configuration register group - which contain the SATA, PCIe mode setting bits +- st,syscfg : Phandle / integer array property. Phandle of sysconfig group + containing the miphy registers and integer array should contain + an entry for each port sub-node, specifying the control + register offset inside the sysconfig group. Required nodes : A sub-node is required for each channel the controller provides. Address range information including the usual @@ -26,7 +28,6 @@ Required properties (port (child) node): registers filled in "reg": - sata: For SATA devices - pcie: For PCIe devices - - syscfg: To specify the syscfg based config register Optional properties (port (child) node): - st,sata-gen : Generation of locally attached SATA IP. Expected values @@ -39,20 +40,20 @@ Example: miphy365x_phy: miphy365x@fe382000 { compatible = "st,miphy365x-phy"; - st,syscfg = <&syscfg_rear>; + st,syscfg = <&syscfg_rear 0x824 0x828>; #address-cells = <1>; #size-cells = <1>; ranges; phy_port0: port@fe382000 { - reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>; - reg-names = "sata", "pcie", "syscfg"; + reg = <0xfe382000 0x100>, <0xfe394000 0x100>; + reg-names = "sata", "pcie"; #phy-cells = <1>; st,sata-gen = <3>; }; phy_port1: port@fe38a000 { - reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;; + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;; reg-names = "sata", "pcie", "syscfg"; #phy-cells = <1>; st,pcie-tx-pol-inv; diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt index 1ef8228db73b..de6a706abcdb 100644 --- a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt @@ -5,10 +5,7 @@ host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC fa Required properties: - compatible : should be "st,stih407-usb2-phy" -- reg : contain the offset and length of the system configuration registers - used as glue logic to control & parameter phy -- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg" -- st,syscfg : sysconfig register to manage phy parameter at driver level +- st,syscfg : phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets - resets : list of phandle and reset specifier pairs. There should be two entries, one for the whole phy and one for the port - reset-names : list of reset signal names. Should be "global" and "port" @@ -19,11 +16,8 @@ Example: usb2_picophy0: usbpicophy@f8 { compatible = "st,stih407-usb2-phy"; - reg = <0xf8 0x04>, /* syscfg 5062 */ - <0xf4 0x04>; /* syscfg 5061 */ - reg-names = "param", "ctrl"; #phy-cells = <0>; - st,syscfg = <&syscfg_core>; + st,syscfg = <&syscfg_core 0x100 0xf4>; resets = <&softreset STIH407_PICOPHY_SOFTRESET>, <&picophyreset STIH407_PICOPHY0_RESET>; reset-names = "global", "port"; diff --git a/Documentation/devicetree/bindings/power/ltc2941.txt b/Documentation/devicetree/bindings/power/ltc2941.txt new file mode 100644 index 000000000000..ea42ae12d924 --- /dev/null +++ b/Documentation/devicetree/bindings/power/ltc2941.txt @@ -0,0 +1,27 @@ +binding for LTC2941 and LTC2943 battery gauges + +Both the LTC2941 and LTC2943 measure battery capacity. +The LTC2943 is compatible with the LTC2941, it adds voltage and +temperature monitoring, and uses a slightly different conversion +formula for the charge counter. + +Required properties: +- compatible: Should contain "ltc2941" or "ltc2943" which also indicates the + type of I2C chip attached. +- reg: The 7-bit I2C address. +- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit + negative value when the battery has been connected to the wrong end of the + resistor. +- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet. + This determines the range and accuracy of the gauge. The value is programmed + into the chip only if it differs from the current setting. The setting is + lost when the battery is disconnected. + +Example from the Topic Miami Florida board: + + fuelgauge: ltc2943@64 { + compatible = "ltc2943"; + reg = <0x64>; + lltc,resistor-sense = <15>; + lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ + }; diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt index 0c94c637f63b..cd2d7f58a9d7 100644 --- a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt @@ -1,20 +1,23 @@ Binding for the LTC2952 PowerPath controller This chip is used to externally trigger a system shut down. Once the trigger has -been sent, the chips' watchdog has to be reset to gracefully shut down. -If the Linux systems decides to shut down it powers off the platform via the -kill signal. +been sent, the chip's watchdog has to be reset to gracefully shut down. +A full powerdown can be triggered via the kill signal. Required properties: - compatible: Must contain: "lltc,ltc2952" -- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the - chip's trigger line - watchdog-gpios: phandle + gpio-specifier for the GPIO connected to the chip's watchdog line - kill-gpios: phandle + gpio-specifier for the GPIO connected to the chip's kill line +Optional properties: +- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's trigger line. If this property is not set, the + trigger function is ignored and the chip is kept alive + until an explicit kill signal is received + Example: ltc2952 { diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index 240019a82f9a..eb618907c7de 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -11,6 +11,7 @@ Required properties: BUCKA and BUCKB. Optional properties: +- enable-gpios: platform gpio for control of BUCKA/BUCKB. - Any optional property defined in regulator.txt Example 1) DA9211 @@ -27,6 +28,7 @@ Example 1) DA9211 regulator-max-microvolt = <1570000>; regulator-min-microamp = <2000000>; regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 27 0>; }; BUCKB { regulator-name = "VBUCKB"; @@ -34,11 +36,12 @@ Example 1) DA9211 regulator-max-microvolt = <1570000>; regulator-min-microamp = <2000000>; regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 17 0>; }; }; }; -Example 2) DA92113 +Example 2) DA9213 pmic: da9213@68 { compatible = "dlg,da9213"; reg = <0x68>; @@ -51,6 +54,7 @@ Example 2) DA92113 regulator-max-microvolt = <1570000>; regulator-min-microamp = <3000000>; regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; }; BUCKB { regulator-name = "VBUCKB"; @@ -58,6 +62,7 @@ Example 2) DA92113 regulator-max-microvolt = <1570000>; regulator-min-microamp = <3000000>; regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 17 0>; }; }; }; diff --git a/Documentation/devicetree/bindings/regulator/isl9305.txt b/Documentation/devicetree/bindings/regulator/isl9305.txt index a626fc1bbf0d..d6e7c9ec9413 100644 --- a/Documentation/devicetree/bindings/regulator/isl9305.txt +++ b/Documentation/devicetree/bindings/regulator/isl9305.txt @@ -2,7 +2,7 @@ Intersil ISL9305/ISL9305H voltage regulator Required properties: -- compatible: "isl,isl9305" or "isl,isl9305h" +- compatible: "isil,isl9305" or "isil,isl9305h" - reg: I2C slave address, usually 0x68. - regulators: A node that houses a sub-node for each regulator within the device. Each sub-node is identified using the node's name, with valid @@ -19,7 +19,7 @@ Optional properties: Example pmic: isl9305@68 { - compatible = "isl,isl9305"; + compatible = "isil,isl9305"; reg = <0x68>; VINDCD1-supply = <&system_power>; diff --git a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt new file mode 100644 index 000000000000..a42b1d6e9863 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt @@ -0,0 +1,217 @@ +Mediatek MT6397 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6397-regulator" +- mt6397regulator: List of regulators provided by this controller. It is named + according to its regulator type, buck_<name> and ldo_<name>. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu, + buck_vdrm, buck_vio18 +LDO: + ldo_vtcxo, ldo_va28, ldo_vcama, ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, + ldo_vemc3v3, ldo_vgp1, ldo_vgp2, ldo_vgp3, ldo_vgp4, ldo_vgp5, ldo_vgp6, + ldo_vibr + +Example: + pmic { + compatible = "mediatek,mt6397"; + + mt6397regulator: mt6397regulator { + compatible = "mediatek,mt6397-regulator"; + + mt6397_vpca15_reg: buck_vpca15 { + regulator-compatible = "buck_vpca15"; + regulator-name = "vpca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <200>; + }; + + mt6397_vpca7_reg: buck_vpca7 { + regulator-compatible = "buck_vpca7"; + regulator-name = "vpca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vsramca15_reg: buck_vsramca15 { + regulator-compatible = "buck_vsramca15"; + regulator-name = "vsramca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vsramca7_reg: buck_vsramca7 { + regulator-compatible = "buck_vsramca7"; + regulator-name = "vsramca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vcore_reg: buck_vcore { + regulator-compatible = "buck_vcore"; + regulator-name = "vcore"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vgpu_reg: buck_vgpu { + regulator-compatible = "buck_vgpu"; + regulator-name = "vgpu"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vdrm_reg: buck_vdrm { + regulator-compatible = "buck_vdrm"; + regulator-name = "vdrm"; + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vio18_reg: buck_vio18 { + regulator-compatible = "buck_vio18"; + regulator-name = "vio18"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2120000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vtcxo_reg: ldo_vtcxo { + regulator-compatible = "ldo_vtcxo"; + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + }; + + mt6397_va28_reg: ldo_va28 { + regulator-compatible = "ldo_va28"; + regulator-name = "va28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vcama_reg: ldo_vcama { + regulator-compatible = "ldo_vcama"; + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vio28_reg: ldo_vio28 { + regulator-compatible = "ldo_vio28"; + regulator-name = "vio28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <240>; + }; + + mt6397_usb_reg: ldo_vusb { + regulator-compatible = "ldo_vusb"; + regulator-name = "vusb"; + /* fixed output 3.3 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmc_reg: ldo_vmc { + regulator-compatible = "ldo_vmc"; + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmch_reg: ldo_vmch { + regulator-compatible = "ldo_vmch"; + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vemc_3v3_reg: ldo_vemc3v3 { + regulator-compatible = "ldo_vemc3v3"; + regulator-name = "vemc_3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp1_reg: ldo_vgp1 { + regulator-compatible = "ldo_vgp1"; + regulator-name = "vcamd"; + regulator-min-microvolt = <1220000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <240>; + }; + + mt6397_vgp2_reg: ldo_vgp2 { + egulator-compatible = "ldo_vgp2"; + regulator-name = "vcamio"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp3_reg: ldo_vgp3 { + regulator-compatible = "ldo_vgp3"; + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp4_reg: ldo_vgp4 { + regulator-compatible = "ldo_vgp4"; + regulator-name = "vgp4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp5_reg: ldo_vgp5 { + regulator-compatible = "ldo_vgp5"; + regulator-name = "vgp5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp6_reg: ldo_vgp6 { + regulator-compatible = "ldo_vgp6"; + regulator-name = "vgp6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vibr_reg: ldo_vibr { + regulator-compatible = "ldo_vibr"; + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index 34ef5d16d0f1..9b40db88f637 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -1,7 +1,7 @@ PFUZE100 family of regulators Required properties: -- compatible: "fsl,pfuze100" or "fsl,pfuze200" +- compatible: "fsl,pfuze100", "fsl,pfuze200", "fsl,pfuze3000" - reg: I2C slave address Required child node: @@ -14,6 +14,8 @@ Required child node: sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 --PFUZE200 sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6 + --PFUZE3000 + sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4 Each regulator is defined using the standard binding for regulators. @@ -205,3 +207,93 @@ Example 2: PFUZE200 }; }; }; + +Example 3: PFUZE3000 + + pmic: pfuze3000@08 { + compatible = "fsl,pfuze3000"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1a { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + /* use sw1c_reg to align with pfuze100/pfuze200 */ + sw1c_reg: sw1b { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1650000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen2_reg: vldo2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vccsd { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: v33 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + }; + + vgen5_reg: vldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt b/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt new file mode 100644 index 000000000000..362a76925bcd --- /dev/null +++ b/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt @@ -0,0 +1,23 @@ +* Device tree bindings for Allwinner A10, A20 PS2 host controller + +A20 PS2 is dual role controller (PS2 host and PS2 device). These bindings are +for PS2 A10/A20 host controller. IBM compliant IBM PS2 and AT-compatible keyboard +and mouse can be connected. + +Required properties: + + - reg : Offset and length of the register set for the device. + - compatible : Should be as of the following: + - "allwinner,sun4i-a10-ps2" + - interrupts : The interrupt line connected to the PS2. + - clocks : The gate clk connected to the PS2. + + +Example: + ps20: ps2@0x01c2a000 { + compatible = "allwinner,sun4i-a10-ps2"; + reg = <0x01c2a000 0x400>; + interrupts = <0 62 4>; + clocks = <&apb1_gates 6>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt b/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt new file mode 100644 index 000000000000..befd125d18bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt @@ -0,0 +1,18 @@ +Bindings for I2S controller built into xtfpga Xtensa bitstreams. + +Required properties: +- compatible: shall be "cdns,xtfpga-i2s". +- reg: memory region (address and length) with device registers. +- interrupts: interrupt for the device. +- clocks: phandle to the clk used as master clock. I2S bus clock + is derived from it. + +Examples: + + i2s0: xtfpga-i2s@0d080000 { + #sound-dai-cells = <0>; + compatible = "cdns,xtfpga-i2s"; + reg = <0x0d080000 0x40>; + interrupts = <2 1>; + clocks = <&cdce706 4>; + }; diff --git a/Documentation/devicetree/bindings/sound/designware-i2s.txt b/Documentation/devicetree/bindings/sound/designware-i2s.txt new file mode 100644 index 000000000000..7bb54247f8e8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/designware-i2s.txt @@ -0,0 +1,31 @@ +DesignWare I2S controller + +Required properties: + - compatible : Must be "snps,designware-i2s" + - reg : Must contain the I2S core's registers location and length + - clocks : Pairs of phandle and specifier referencing the controller's + clocks. The controller expects one clock: the clock used as the sampling + rate reference clock sample. + - clock-names : "i2sclk" for the sample rate reference clock. + - dmas: Pairs of phandle and specifier for the DMA channels that are used by + the core. The core expects one or two dma channels: one for transmit and + one for receive. + - dma-names : "tx" for the transmit channel, "rx" for the receive channel. + +For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' +properties please check: + * resource-names.txt + * clock/clock-bindings.txt + * dma/dma.txt + +Example: + + soc_i2s: i2s@7ff90000 { + compatible = "snps,designware-i2s"; + reg = <0x0 0x7ff90000 0x0 0x1000>; + clocks = <&scpi_i2sclk 0>; + clock-names = "i2sclk"; + #sound-dai-cells = <0>; + dmas = <&dma0 5>; + dma-names = "tx"; + }; diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt new file mode 100644 index 000000000000..b41433386e2f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt @@ -0,0 +1,23 @@ +Ingenic JZ4740 I2S controller + +Required properties: +- compatible : "ingenic,jz4740-i2s" +- reg : I2S registers location and length +- clocks : AIC and I2S PLL clock specifiers. +- clock-names: "aic" and "i2s" +- dmas: DMA controller phandle and DMA request line for I2S Tx and Rx channels +- dma-names: Must be "tx" and "rx" + +Example: + +i2s: i2s@10020000 { + compatible = "ingenic,jz4740-i2s"; + reg = <0x10020000 0x94>; + + clocks = <&cgu JZ4740_CLK_AIC>, <&cgu JZ4740_CLK_I2SPLL>; + clock-names = "aic", "i2s"; + + dmas = <&dma 2>, <&dma 3>; + dma-names = "tx", "rx"; + +}; diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt new file mode 100644 index 000000000000..a7a149a236e5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -0,0 +1,14 @@ +Maxim MAX98357A audio DAC + +This node models the Maxim MAX98357A DAC. + +Required properties: +- compatible : "maxim,max98357a" +- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin + +Example: + +max98357a { + compatible = "maxim,max98357a"; + sdmode-gpios = <&qcom_pinmux 25 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt new file mode 100644 index 000000000000..a4589cda214e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt @@ -0,0 +1,67 @@ +NVIDIA Tegra audio complex, with RT5677 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-rt5677" +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the RT5677's pins (as documented in its binding), and the jacks + on the board: + + * Headphone + * Speaker + * Headset Mic + * Internal Mic 1 + * Internal Mic 2 + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the RT5677 audio codec. This binding + assumes that AIF1 on the CODEC is connected to Tegra. + +Optional properties: +- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in +- nvidia,hp-en-gpios : The GPIO that enables headphone amplifier +- nvidia,mic-present-gpios: The GPIO that mic jack is plugged in +- nvidia,dmic-clk-en-gpios : The GPIO that gates DMIC clock signal + +Example: + +sound { + compatible = "nvidia,tegra-audio-rt5677-ryu", + "nvidia,tegra-audio-rt5677"; + nvidia,model = "NVIDIA Tegra Ryu"; + + nvidia,audio-routing = + "Headphone", "LOUT2", + "Headphone", "LOUT1", + "Headset Mic", "MICBIAS1", + "IN1P", "Headset Mic", + "IN1N", "Headset Mic", + "DMIC L1", "Internal Mic 1", + "DMIC R1", "Internal Mic 1", + "DMIC L2", "Internal Mic 2", + "DMIC R2", "Internal Mic 2", + "Speaker", "PDM1L", + "Speaker", "PDM1R"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&rt5677>; + + nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; + nvidia,mic-present-gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>; + nvidia,hp-en-gpios = <&rt5677 1 GPIO_ACTIVE_HIGH>; + nvidia,dmic-clk-en-gpios = <&rt5677 2 GPIO_ACTIVE_HIGH>; + + clocks = <&tegra_car TEGRA124_CLK_PLL_A>, + <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA124_CLK_EXTERN1>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/pcm512x.txt b/Documentation/devicetree/bindings/sound/pcm512x.txt index faff75e64573..3aae3b41bd8e 100644 --- a/Documentation/devicetree/bindings/sound/pcm512x.txt +++ b/Documentation/devicetree/bindings/sound/pcm512x.txt @@ -5,7 +5,8 @@ on the board). Required properties: - - compatible : One of "ti,pcm5121" or "ti,pcm5122" + - compatible : One of "ti,pcm5121", "ti,pcm5122", "ti,pcm5141" or + "ti,pcm5142" - reg : the I2C address of the device for I2C, the chip select number for SPI. @@ -16,9 +17,16 @@ Required properties: Optional properties: - clocks : A clock specifier for the clock connected as SCLK. If this - is absent the device will be configured to clock from BCLK. + is absent the device will be configured to clock from BCLK. If pll-in + and pll-out are specified in addition to a clock, the device is + configured to accept clock input on a specified gpio pin. -Example: + - pll-in, pll-out : gpio pins used to connect the pll using <1> + through <6>. The device will be configured for clock input on the + given pll-in pin and PLL output on the given pll-out pin. An + external connection from the pll-out pin to the SCLK pin is assumed. + +Examples: pcm5122: pcm5122@4c { compatible = "ti,pcm5122"; @@ -28,3 +36,17 @@ Example: DVDD-supply = <®_1v8>; CPVDD-supply = <®_3v3>; }; + + + pcm5142: pcm5142@4c { + compatible = "ti,pcm5142"; + reg = <0x4c>; + + AVDD-supply = <®_3v3_analog>; + DVDD-supply = <®_1v8>; + CPVDD-supply = <®_3v3>; + + clocks = <&sck>; + pll-in = <3>; + pll-out = <6>; + }; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt index d188296bb6ec..09e0e18591ae 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.txt +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -33,6 +33,25 @@ Required SoC Specific Properties: "iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2 doesn't have any such mux. +- #clock-cells: should be 1, this property must be present if the I2S device + is a clock provider in terms of the common clock bindings, described in + ../clock/clock-bindings.txt. +- clock-output-names: from the common clock bindings, names of the CDCLK + I2S output clocks, suggested values are "i2s_cdclk0", "i2s_cdclk1", + "i2s_cdclk3" for the I2S0, I2S1, I2S2 devices recpectively. + +There are following clocks available at the I2S device nodes: + CLK_I2S_CDCLK - the CDCLK (CODECLKO) gate clock, + CLK_I2S_RCLK_PSR - the RCLK prescaler divider clock (corresponding to the + IISPSR register), + CLK_I2S_RCLK_SRC - the RCLKSRC mux clock (corresponding to RCLKSRC bit in + IISMOD register). + +Refer to the SoC datasheet for availability of the above clocks. +The CLK_I2S_RCLK_PSR and CLK_I2S_RCLK_SRC clocks are usually only available +in the IIS Multi Audio Interface (I2S0). +Note: Old DTs may not have the #clock-cells, clock-output-names properties +and then not use the I2S node as a clock supplier. Optional SoC Specific Properties: @@ -41,6 +60,7 @@ Optional SoC Specific Properties: - pinctrl-0: Should specify pin control groups used for this controller. - pinctrl-names: Should contain only one value - "default". + Example: i2s0: i2s@03830000 { @@ -54,6 +74,8 @@ i2s0: i2s@03830000 { <&clock_audss EXYNOS_I2S_BUS>, <&clock_audss EXYNOS_SCLK_I2S>; clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; + #clock-cells; + clock-output-names = "i2s_cdclk0"; samsung,idma-addr = <0x03000000>; pinctrl-names = "default"; pinctrl-0 = <&i2s0_bus>; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index c3cba600bf11..73bf314f7240 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -75,6 +75,11 @@ Optional CPU/CODEC subnodes properties: it can be specified via "clocks" if system has clock node (= common clock), or "system-clock-frequency" (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). Example 1 - single DAI link: diff --git a/Documentation/devicetree/bindings/sound/st,sta32x.txt b/Documentation/devicetree/bindings/sound/st,sta32x.txt new file mode 100644 index 000000000000..255de3ae5b2f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta32x.txt @@ -0,0 +1,92 @@ +STA32X audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta32x" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - Vdda-supply: regulator spec, providing 3.3V + - Vdd3-supply: regulator spec, providing 3.3V + - Vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + This property has to be specified as '/bits/ 8' value. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is chosen. + This properties have to be specified as '/bits/ 8' values. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,invalid-input-detect-mute: + If present, automatic invalid input detect mute is enabled. + +Example: + +codec: sta32x@38 { + compatible = "st,sta32x"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 5e6040c2c2e9..47a213c411ce 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -9,6 +9,7 @@ Required properties: "ti,tlv320aic33" - TLV320AIC33 "ti,tlv320aic3007" - TLV320AIC3007 "ti,tlv320aic3106" - TLV320AIC3106 + "ti,tlv320aic3104" - TLV320AIC3104 - reg - <int> - I2C slave address @@ -18,6 +19,7 @@ Optional properties: - gpio-reset - gpio pin number used for codec reset - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality + - Not supported on tlv320aic3104 - ai3x-micbias-vg - MicBias Voltage required. 1 - MICBIAS output is powered to 2.0V, 2 - MICBIAS output is powered to 2.5V, @@ -36,7 +38,13 @@ CODEC output pins: * HPLCOM * HPRCOM -CODEC input pins: +CODEC input pins for TLV320AIC3104: + * MIC2L + * MIC2R + * LINE1L + * LINE1R + +CODEC input pins for other compatible codecs: * MIC3L * MIC3R * LINE1L diff --git a/Documentation/devicetree/bindings/sound/ts3a227e.txt b/Documentation/devicetree/bindings/sound/ts3a227e.txt index e8bf23eb1803..a836881d9608 100644 --- a/Documentation/devicetree/bindings/sound/ts3a227e.txt +++ b/Documentation/devicetree/bindings/sound/ts3a227e.txt @@ -13,6 +13,11 @@ Required properties: - interrupt-parent: The parent interrupt controller - interrupts: Interrupt number for /INT pin from the 227e +Optional properies: + - ti,micbias: Intended MICBIAS voltage (datasheet section 9.6.7). + Select 0/1/2/3/4/5/6/7 to specify MACBIAS voltage + 2.1V/2.2V/2.3V/2.4V/2.5V/2.6V/2.7V/2.8V + Default value is "1" (2.2V). Examples: diff --git a/Documentation/devicetree/bindings/sound/wm8904.txt b/Documentation/devicetree/bindings/sound/wm8904.txt index e99f4097c83c..66bf261423b9 100644 --- a/Documentation/devicetree/bindings/sound/wm8904.txt +++ b/Documentation/devicetree/bindings/sound/wm8904.txt @@ -3,7 +3,7 @@ WM8904 audio CODEC This device supports I2C only. Required properties: - - compatible: "wlf,wm8904" + - compatible: "wlf,wm8904" or "wlf,wm8912" - reg: the I2C address of the device. - clock-names: "mclk" - clocks: reference to diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index d11c3721e7cd..4c388bb2f0a2 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -30,6 +30,22 @@ Optional properties: specifiers, one for transmission, and one for reception. - dma-names : Must contain a list of two DMA names, "tx" and "rx". +- renesas,dtdl : delay sync signal (setup) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + +- renesas,syncdl : delay sync signal (hold) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + 300 (3-clock-cycle delay) Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words diff --git a/Documentation/devicetree/bindings/spi/spi-sirf.txt b/Documentation/devicetree/bindings/spi/spi-sirf.txt new file mode 100644 index 000000000000..4c7adb8f777c --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sirf.txt @@ -0,0 +1,41 @@ +* CSR SiRFprimaII Serial Peripheral Interface + +Required properties: +- compatible : Should be "sirf,prima2-spi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI interrupt +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + +- #address-cells: Number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be zero. + +Optional properties: +- spi-max-frequency: Specifies maximum SPI clock frequency, + Units - Hz. Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +- cs-gpios: should specify GPIOs used for chipselects. + +Example: + +spi0: spi@b00d0000 { + compatible = "sirf,prima2-spi"; + reg = <0xb00d0000 0x10000>; + interrupts = <15>; + dmas = <&dmac1 9>, + <&dmac1 4>; + dma-names = "rx", "tx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clks 19>; + resets = <&rstc 26>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-st-ssc.txt b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt new file mode 100644 index 000000000000..fe54959ec957 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt @@ -0,0 +1,40 @@ +STMicroelectronics SSC (SPI) Controller +--------------------------------------- + +Required properties: +- compatible : "st,comms-ssc4-spi" +- reg : Offset and length of the device's register set +- interrupts : The interrupt specifier +- clock-names : Must contain "ssc" +- clocks : Must contain an entry for each name in clock-names + See ../clk/* +- pinctrl-names : Uses "default", can use "sleep" if provided + See ../pinctrl/pinctrl-binding.txt + +Optional properties: +- cs-gpios : List of GPIO chip selects + See ../spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + spi@9840000 { + compatible = "st,comms-ssc4-spi"; + reg = <0x9840000 0x110>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; + clock-names = "ssc"; + pinctrl-0 = <&pinctrl_spi0_default>; + pinctrl-names = "default"; + cs-gpios = <&pio17 5 0>; + #address-cells = <1>; + #size-cells = <0>; + + st95hf@0{ + compatible = "st,st95hf"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + }; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index b1df0ad1306c..96a17541391e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -9,7 +9,6 @@ ad Avionic Design GmbH adapteva Adapteva, Inc. adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB -ak Asahi Kasei Corp. allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) @@ -20,6 +19,7 @@ amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. armadeus ARMadeus Systems SARL +asahi-kasei Asahi Kasei Corp. atmel Atmel Corporation auo AU Optronics Corporation avago Avago Technologies @@ -54,6 +54,7 @@ epcos EPCOS AG epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. est ESTeem Wireless Modems +ettus NI Ettus Research eukrea Eukréa Electromatique everest Everest Semiconductor Co. Ltd. excito Excito @@ -127,6 +128,7 @@ pixcir PIXCIR MICROELECTRONICS Co., Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc +qemu QEMU, a generic and open source machine emulator and virtualizer qnap QNAP Systems, Inc. radxa Radxa raidsonic RaidSonic Technology GmbH @@ -168,6 +170,7 @@ usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor variscite Variscite Ltd. via VIA Technologies, Inc. +virtio Virtual I/O Device Specification, developed by the OASIS consortium voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. wlf Wolfson Microelectronics diff --git a/Documentation/devicetree/bindings/video/ti,dra7-dss.txt b/Documentation/devicetree/bindings/video/ti,dra7-dss.txt new file mode 100644 index 000000000000..f33a05137b0e --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,dra7-dss.txt @@ -0,0 +1,69 @@ +Texas Instruments DRA7x Display Subsystem +========================================= + +See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,dra7-dss" +- reg: address and length of the register spaces for 'dss' +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" +- syscon: phandle to control module core syscon node + +Optional properties: + +Some DRA7xx SoCs have one dedicated video PLL, some have two. These properties +can be used to describe the video PLLs: + +- reg: address and length of the register spaces for 'pll1_clkctrl', + 'pll1', 'pll2_clkctrl', 'pll2' +- clocks: handle to video1 pll clock and video2 pll clock +- clock-names: "video1_clk" and "video2_clk" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,dra7-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + +HDMI +---- + +Required properties: +- compatible: "ti,dra7-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/video/ti,opa362.txt b/Documentation/devicetree/bindings/video/ti,opa362.txt new file mode 100644 index 000000000000..f96083c0bd17 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,opa362.txt @@ -0,0 +1,38 @@ +OPA362 analog video amplifier + +Required properties: +- compatible: "ti,opa362" +- enable-gpios: enable/disable output gpio + +Required node: +- Video port 0 for opa362 input +- Video port 1 for opa362 output + +Example: + +tv_amp: opa362 { + compatible = "ti,opa362"; + enable-gpios = <&gpio1 23 0>; /* GPIO to enable video out amplifier */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + opa_in: endpoint@0 { + remote-endpoint = <&venc_out>; + }; + }; + + port@1 { + reg = <1>; + opa_out: endpoint@0 { + remote-endpoint = <&tv_connector_in>; + }; + }; + }; +}; + + + |