diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
45 files changed, 1177 insertions, 57 deletions
diff --git a/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt b/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt new file mode 100644 index 000000000000..94e642a33db0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt @@ -0,0 +1,15 @@ +Calxeda Highbank L2 cache ECC + +Properties: +- compatible : Should be "calxeda,hb-sregs-l2-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. + +Example: + + sregs@fff3c200 { + compatible = "calxeda,hb-sregs-l2-ecc"; + reg = <0xfff3c200 0x100>; + interrupts = <0 71 4 0 72 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt new file mode 100644 index 000000000000..f770ac0893d4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt @@ -0,0 +1,14 @@ +Calxeda DDR memory controller + +Properties: +- compatible : Should be "calxeda,hb-ddr-ctrl" +- reg : Address and size for DDR controller registers. +- interrupts : Interrupt for DDR controller. + +Example: + + memory-controller@fff00000 { + compatible = "calxeda,hb-ddr-ctrl"; + reg = <0xfff00000 0x1000>; + interrupts = <0 91 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/mrvl/intc.txt b/Documentation/devicetree/bindings/arm/mrvl/intc.txt index 80b9a94d9a23..8b53273cb22f 100644 --- a/Documentation/devicetree/bindings/arm/mrvl/intc.txt +++ b/Documentation/devicetree/bindings/arm/mrvl/intc.txt @@ -38,3 +38,23 @@ Example: reg-names = "mux status", "mux mask"; mrvl,intc-nr-irqs = <2>; }; + +* Marvell Orion Interrupt controller + +Required properties +- compatible : Should be "marvell,orion-intc". +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. Supported value is <1>. +- interrupt-controller : Declare this node to be an interrupt controller. +- reg : Interrupt mask address. A list of 4 byte ranges, one per controller. + One entry in the list represents 32 interrupts. + +Example: + + intc: interrupt-controller { + compatible = "marvell,orion-intc", "marvell,intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0xfed20204 0x04>, + <0xfed20214 0x04>; + }; diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt new file mode 100644 index 000000000000..93986a5a8018 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt @@ -0,0 +1,30 @@ +* Compact Flash + +The Cavium Compact Flash device is connected to the Octeon Boot Bus, +and is thus a child of the Boot Bus device. It can read and write +industry standard compact flash devices. + +Properties: +- compatible: "cavium,ebt3000-compact-flash"; + + Compatibility with many Cavium evaluation boards. + +- reg: The base address of the the CF chip select banks. Depending on + the device configuration, there may be one or two banks. + +- cavium,bus-width: The width of the connection to the CF devices. Valid + values are 8 and 16. + +- cavium,true-ide: Optional, if present the CF connection is in True IDE mode. + +- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected + to this device. + +Example: + compact-flash@5,0 { + compatible = "cavium,ebt3000-compact-flash"; + reg = <5 0 0x10000>, <6 0 0x10000>; + cavium,bus-width = <16>; + cavium,true-ide; + cavium,dma-engine-handle = <&dma0>; + }; diff --git a/Documentation/devicetree/bindings/ata/marvell.txt b/Documentation/devicetree/bindings/ata/marvell.txt new file mode 100644 index 000000000000..b5cdd20cde9c --- /dev/null +++ b/Documentation/devicetree/bindings/ata/marvell.txt @@ -0,0 +1,16 @@ +* Marvell Orion SATA + +Required Properties: +- compatibility : "marvell,orion-sata" +- reg : Address range of controller +- interrupts : Interrupt controller is using +- nr-ports : Number of SATA ports in use. + +Example: + + sata@80000 { + compatible = "marvell,orion-sata"; + reg = <0x80000 0x5000>; + interrupts = <21>; + nr-ports = <2>; + } diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt new file mode 100644 index 000000000000..9d6dcd3fe7f9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt @@ -0,0 +1,49 @@ +* General Purpose Input Output (GPIO) bus. + +Properties: +- compatible: "cavium,octeon-3860-gpio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the GPIO unit's register bank. + +- gpio-controller: This is a GPIO controller. + +- #gpio-cells: Must be <2>. The first cell is the GPIO pin. + +- interrupt-controller: The GPIO controller is also an interrupt + controller, many of its pins may be configured as an interrupt + source. + +- #interrupt-cells: Must be <2>. The first cell is the GPIO pin + connected to the interrupt source. The second cell is the interrupt + triggering protocol and may have one of four values: + 1 - edge triggered on the rising edge. + 2 - edge triggered on the falling edge + 4 - level triggered active high. + 8 - level triggered active low. + +- interrupts: Interrupt routing for each pin. + +Example: + + gpio-controller@1070000000800 { + #gpio-cells = <2>; + compatible = "cavium,octeon-3860-gpio"; + reg = <0x10700 0x00000800 0x0 0x100>; + gpio-controller; + /* Interrupts are specified by two parts: + * 1) GPIO pin number (0..15) + * 2) Triggering (1 - edge rising + * 2 - edge falling + * 4 - level active high + * 8 - level active low) + */ + interrupt-controller; + #interrupt-cells = <2>; + /* The GPIO pin connect to 16 consecutive CUI bits */ + interrupts = <0 16>, <0 17>, <0 18>, <0 19>, + <0 20>, <0 21>, <0 22>, <0 23>, + <0 24>, <0 25>, <0 26>, <0 27>, + <0 28>, <0 29>, <0 30>, <0 31>; + }; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt index 4f3929713ae4..dbd22e0df21e 100644 --- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -22,7 +22,7 @@ Required properties: Example: gpio0: gpio@73f84000 { - compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + compatible = "fsl,imx51-gpio", "fsl,imx35-gpio"; reg = <0x73f84000 0x4000>; interrupts = <50 51>; gpio-controller; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index 8f50fe5e6c42..5375625e8cd2 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -11,14 +11,15 @@ Required properties: <[phandle of the gpio controller node] [pin number within the gpio controller] [mux function] - [pull up/down] + [flags and pull up/down] [drive strength]> Values for gpio specifier: - Pin number: is a value between 0 to 7. - - Pull Up/Down: 0 - Pull Up/Down Disabled. - 1 - Pull Down Enabled. - 3 - Pull Up Enabled. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. - Drive Strength: 0 - 1x, 1 - 3x, 2 - 2x, diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 05428f39d9ac..e13787498bcf 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -27,3 +27,26 @@ Example: interrupt-controller; #interrupt-cells = <1>; }; + +* Marvell Orion GPIO Controller + +Required properties: +- compatible : Should be "marvell,orion-gpio" +- reg : Address and length of the register set for controller. +- gpio-controller : So we know this is a gpio controller. +- ngpio : How many gpios this controller has. +- interrupts : Up to 4 Interrupts for the controller. + +Optional properties: +- mask-offset : For SMP Orions, offset for Nth CPU + +Example: + + gpio0: gpio@10100 { + compatible = "marvell,orion-gpio"; + #gpio-cells = <2>; + gpio-controller; + reg = <0x10100 0x40>; + ngpio = <32>; + interrupts = <35>, <36>, <37>, <38>; + }; diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt new file mode 100644 index 000000000000..dced82ebe31d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt @@ -0,0 +1,34 @@ +* Two Wire Serial Interface (TWSI) / I2C + +- compatible: "cavium,octeon-3860-twsi" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the TWSI/I2C bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. I2C addresses have no size component. + +- interrupts: A single interrupt specifier. + +- clock-frequency: The I2C bus clock rate in Hz. + +Example: + twsi0: i2c@1180000001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cavium,octeon-3860-twsi"; + reg = <0x11800 0x00001000 0x0 0x200>; + interrupts = <0 45>; + clock-frequency = <100000>; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + }; + tmp@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt index 4f8ec947c6bd..4f8ec947c6bd 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt +++ b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt index 1bfc02de1b0c..30ac3a0557f7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -4,6 +4,8 @@ Required properties: - compatible: Should be "fsl,<chip>-i2c" - reg: Should contain registers location and length - interrupts: Should contain ERROR and DMA interrupts +- clock-frequency: Desired I2C bus clock frequency in Hz. + Only 100000Hz and 400000Hz modes are supported. Examples: @@ -13,4 +15,5 @@ i2c0: i2c@80058000 { compatible = "fsl,imx28-i2c"; reg = <0x80058000 2000>; interrupts = <111 68>; + clock-frequency = <100000>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt new file mode 100644 index 000000000000..c15781f4dc8c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -0,0 +1,33 @@ +Device tree configuration for i2c-ocores + +Required properties: +- compatible : "opencores,i2c-ocores" +- reg : bus address start and address range size of device +- interrupts : interrupt number +- clock-frequency : frequency of bus clock in Hz +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- reg-shift : device register offsets are shifted by this value +- reg-io-width : io register width in bytes (1, 2 or 4) +- regstep : deprecated, use reg-shift above + +Example: + + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + clock-frequency = <20000000>; + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt index b891ee218354..0f7945019f6f 100644 --- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt @@ -1,4 +1,4 @@ -* I2C +* Marvell MMP I2C controller Required properties : @@ -32,3 +32,20 @@ Examples: interrupts = <58>; }; +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be "marvell,mv64xxx-i2c" + - interrupts : The interrupt number + - clock-frequency : Desired I2C bus clock frequency in Hz. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt new file mode 100644 index 000000000000..31afd5014c48 --- /dev/null +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -0,0 +1,28 @@ +NXP LPC32xx Key Scan Interface + +Required Properties: +- compatible: Should be "nxp,lpc3220-key" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. +- keypad,num-rows: Number of rows and columns, e.g. 1: 1x1, 6: 6x6 +- keypad,num-columns: Must be equal to keypad,num-rows since LPC32xx only + supports square matrices +- nxp,debounce-delay-ms: Debounce delay in ms +- nxp,scan-delay-ms: Repeated scan period in ms +- linux,keymap: the key-code to be reported when the key is pressed + and released, see also + Documentation/devicetree/bindings/input/matrix-keymap.txt + +Example: + + key@40050000 { + compatible = "nxp,lpc3220-key"; + reg = <0x40050000 0x1000>; + interrupts = <54 0>; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt new file mode 100644 index 000000000000..f2fa5e10493d --- /dev/null +++ b/Documentation/devicetree/bindings/input/omap-keypad.txt @@ -0,0 +1,31 @@ +* TI's Keypad Controller device tree bindings + +TI's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "ti,omap4-keypad": For controllers compatible with omap4 keypad + controller. + +Required Board Specific Properties, in addition to those specified by +the shared matrix-keyboard bindings: +- keypad,num-rows: Number of row lines connected to the keypad + controller. + +- keypad,num-columns: Number of column lines connected to the + keypad controller. + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. + +Example: + keypad@4ae1c000{ + compatible = "ti,omap4-keypad"; + keypad,num-rows = <2>; + keypad,num-columns = <8>; + linux,keypad-no-autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/twl6040-vibra.txt b/Documentation/devicetree/bindings/input/twl6040-vibra.txt deleted file mode 100644 index 5b1918b818fb..000000000000 --- a/Documentation/devicetree/bindings/input/twl6040-vibra.txt +++ /dev/null @@ -1,37 +0,0 @@ -Vibra driver for the twl6040 family - -The vibra driver is a child of the twl6040 MFD dirver. -Documentation/devicetree/bindings/mfd/twl6040.txt - -Required properties: -- compatible : Must be "ti,twl6040-vibra"; -- interrupts: 4, Vibra overcurrent interrupt -- vddvibl-supply: Regulator supplying the left vibra motor -- vddvibr-supply: Regulator supplying the right vibra motor -- vibldrv_res: Board specific left driver resistance -- vibrdrv_res: Board specific right driver resistance -- viblmotor_res: Board specific left motor resistance -- vibrmotor_res: Board specific right motor resistance - -Optional properties: -- vddvibl_uV: If the vddvibl default voltage need to be changed -- vddvibr_uV: If the vddvibr default voltage need to be changed - -Example: -/* - * 8-channel high quality low-power audio codec - * http://www.ti.com/lit/ds/symlink/twl6040.pdf - */ -twl6040: twl6040@4b { - ... - twl6040_vibra: twl6040@1 { - compatible = "ti,twl6040-vibra"; - interrupts = <4>; - vddvibl-supply = <&vbat>; - vddvibr-supply = <&vbat>; - vibldrv_res = <8>; - vibrdrv_res = <3>; - viblmotor_res = <10>; - vibrmotor_res = <10>; - }; -}; diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt new file mode 100644 index 000000000000..69e757a657a0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -0,0 +1,123 @@ +* AB8500 Multi-Functional Device (MFD) + +Required parent device properties: +- compatible : contains "stericsson,ab8500"; +- interrupts : contains the IRQ line for the AB8500 +- interrupt-controller : describes the AB8500 as an Interrupt Controller (has its own domain) +- #interrupt-cells : should be 2, for 2-cell format + - The first cell is the AB8500 local IRQ number + - The second cell is used to specify optional parameters + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + +Optional parent device properties: +- reg : contains the PRCMU mailbox address for the AB8500 i2c port + +The AB8500 consists of a large and varied group of sub-devices: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +ab8500-bm : : : Battery Manager +ab8500-btemp : : : Battery Temperature +ab8500-charger : : : Battery Charger +ab8500-fg : : : Fuel Gauge +ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter + SW_CONV_END : : +ab8500-gpio : : : GPIO Controller +ab8500-ponkey : ONKEY_DBF : : Power-on Key + ONKEY_DBR : : +ab8500-pwm : : : Pulse Width Modulator +ab8500-regulator : : : Regulators +ab8500-rtc : 60S : : Real Time Clock + : ALARM : : +ab8500-sysctrl : : : System Control +ab8500-usb : ID_WAKEUP_R : vddulpivio18 : Universal Serial Bus + : ID_WAKEUP_F : v-ape : + : VBUS_DET_F : musb_1v8 : + : VBUS_DET_R : : + : USB_LINK_STATUS : : + : USB_ADP_PROBE_PLUG : : + : USB_ADP_PROBE_UNPLUG : : + +Required child device properties: +- compatible : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey| + pwm|regulator|rtc|sysctrl|usb]"; + +Optional child device properties: +- interrupts : contains the device IRQ(s) using the 2-cell format (see above) +- interrupt-names : contains names of IRQ resource in the order in which they were + supplied in the interrupts property +- <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree + +ab8500@5 { + compatible = "stericsson,ab8500"; + reg = <5>; /* mailbox 5 is i2c */ + interrupts = <0 40 0x4>; + interrupt-controller; + #interrupt-cells = <2>; + + ab8500-rtc { + compatible = "stericsson,ab8500-rtc"; + interrupts = <17 0x4 + 18 0x4>; + interrupt-names = "60S", "ALARM"; + }; + + ab8500-gpadc { + compatible = "stericsson,ab8500-gpadc"; + interrupts = <32 0x4 + 39 0x4>; + interrupt-names = "HW_CONV_END", "SW_CONV_END"; + vddadc-supply = <&ab8500_ldo_tvout_reg>; + }; + + ab8500-usb { + compatible = "stericsson,ab8500-usb"; + interrupts = < 90 0x4 + 96 0x4 + 14 0x4 + 15 0x4 + 79 0x4 + 74 0x4 + 75 0x4>; + interrupt-names = "ID_WAKEUP_R", + "ID_WAKEUP_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_ADP_PROBE_PLUG", + "USB_ADP_PROBE_UNPLUG"; + vddulpivio18-supply = <&ab8500_ldo_initcore_reg>; + v-ape-supply = <&db8500_vape_reg>; + musb_1v8-supply = <&db8500_vsmps2_reg>; + }; + + ab8500-ponkey { + compatible = "stericsson,ab8500-ponkey"; + interrupts = <6 0x4 + 7 0x4>; + interrupt-names = "ONKEY_DBF", "ONKEY_DBR"; + }; + + ab8500-sysctrl { + compatible = "stericsson,ab8500-sysctrl"; + }; + + ab8500-pwm { + compatible = "stericsson,ab8500-pwm"; + }; + + ab8500-regulators { + compatible = "stericsson,ab8500-regulator"; + + ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { + /* + * See: Documentation/devicetree/bindings/regulator/regulator.txt + * for more information on regulators + */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt new file mode 100644 index 000000000000..c6a3469d3436 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -0,0 +1,59 @@ +Maxim MAX77686 multi-function device + +MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is +interfaced to host controller using i2c interface. PMIC and Charger submodules +are addressed using same i2c slave address whereas RTC submodule uses +different i2c slave address,presently for which we are statically creating i2c +client while probing.This document describes the binding for mfd device and +PMIC submodule. + +Required properties: +- compatible : Must be "maxim,max77686"; +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional node: +- voltage-regulators : The regulators of max77686 have to be instantiated + under subnode named "voltage-regulators" using the following format. + + regulator_name { + regulator-compatible = LDOn/BUCKn + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + + The regulator-compatible property of regulator should initialized with string +to get matched with their hardware counterparts as follow: + + -LDOn : for LDOs, where n can lie in range 1 to 26. + example: LDO1, LDO2, LDO26. + -BUCKn : for BUCKs, where n can lie in range 1 to 9. + example: BUCK1, BUCK5, BUCK9. + +Example: + + max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + + voltage-regulators { + ldo11_reg { + regulator-compatible = "LDO11"; + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + + buck1_reg { + regulator-compatible = "BUCK1"; + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + } diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index d2802d4717bc..db03599ae4dc 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -81,7 +81,7 @@ Example: ti,vmbch-threshold = 0; ti,vmbch2-threshold = 0; - + ti,en-ck32k-xtal; ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; vcc1-supply = <®_parent>; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt index bc67c6f424aa..c855240f3a0e 100644 --- a/Documentation/devicetree/bindings/mfd/twl6040.txt +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -6,7 +6,7 @@ They are connected ot the host processor via i2c for commands, McPDM for audio data and commands. Required properties: -- compatible : Must be "ti,twl6040"; +- compatible : "ti,twl6040" for twl6040, "ti,twl6041" for twl6041 - reg: must be 0x4b for i2c address - interrupts: twl6040 has one interrupt line connecteded to the main SoC - interrupt-parent: The parent interrupt controller diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt new file mode 100644 index 000000000000..6581478225a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt @@ -0,0 +1,126 @@ +* Boot Bus + +The Octeon Boot Bus is a configurable parallel bus with 8 chip +selects. Each chip select is independently configurable. + +Properties: +- compatible: "cavium,octeon-3860-bootbus" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the Boot Bus' register bank. + +- #address-cells: Must be <2>. The first cell is the chip select + within the bootbus. The second cell is the offset from the chip select. + +- #size-cells: Must be <1>. + +- ranges: There must be one one triplet of (child-bus-address, + parent-bus-address, length) for each active chip select. If the + length element for any triplet is zero, the chip select is disabled, + making it inactive. + +The configuration parameters for each chip select are stored in child +nodes. + +Configuration Properties: +- compatible: "cavium,octeon-3860-bootbus-config" + +- cavium,cs-index: A single cell indicating the chip select that + corresponds to this configuration. + +- cavium,t-adr: A cell specifying the ADR timing (in nS). + +- cavium,t-ce: A cell specifying the CE timing (in nS). + +- cavium,t-oe: A cell specifying the OE timing (in nS). + +- cavium,t-we: A cell specifying the WE timing (in nS). + +- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS). + +- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS). + +- cavium,t-pause: A cell specifying the PAUSE timing (in nS). + +- cavium,t-wait: A cell specifying the WAIT timing (in nS). + +- cavium,t-page: A cell specifying the PAGE timing (in nS). + +- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS). + +- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1 + = 2 bytes, 2 = 4 bytes, 3 = 8 bytes). + +- cavium,wait-mode: Optional. If present, wait mode (WAITM) is selected. + +- cavium,page-mode: Optional. If present, page mode (PAGEM) is selected. + +- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of + the bus for this chip select. + +- cavium,ale-mode: Optional. If present, ALE mode is selected. + +- cavium,sam-mode: Optional. If present, SAM mode is selected. + +- cavium,or-mode: Optional. If present, OR mode is selected. + +Example: + bootbus: bootbus@1180000000000 { + compatible = "cavium,octeon-3860-bootbus"; + reg = <0x11800 0x00000000 0x0 0x200>; + /* The chip select number and offset */ + #address-cells = <2>; + /* The size of the chip select region */ + #size-cells = <1>; + ranges = <0 0 0x0 0x1f400000 0xc00000>, + <1 0 0x10000 0x30000000 0>, + <2 0 0x10000 0x40000000 0>, + <3 0 0x10000 0x50000000 0>, + <4 0 0x0 0x1d020000 0x10000>, + <5 0 0x0 0x1d040000 0x10000>, + <6 0 0x0 0x1d050000 0x10000>, + <7 0 0x10000 0x90000000 0>; + + cavium,cs-config@0 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <0>; + cavium,t-adr = <20>; + cavium,t-ce = <60>; + cavium,t-oe = <60>; + cavium,t-we = <45>; + cavium,t-rd-hld = <35>; + cavium,t-wr-hld = <45>; + cavium,t-pause = <0>; + cavium,t-wait = <0>; + cavium,t-page = <35>; + cavium,t-rd-dly = <0>; + + cavium,pages = <0>; + cavium,bus-width = <8>; + }; + . + . + . + cavium,cs-config@6 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <6>; + cavium,t-adr = <5>; + cavium,t-ce = <300>; + cavium,t-oe = <270>; + cavium,t-we = <150>; + cavium,t-rd-hld = <100>; + cavium,t-wr-hld = <70>; + cavium,t-pause = <0>; + cavium,t-wait = <0>; + cavium,t-page = <320>; + cavium,t-rd-dly = <0>; + + cavium,pages = <0>; + cavium,wait-mode; + cavium,bus-width = <16>; + }; + . + . + . + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt new file mode 100644 index 000000000000..2c2d0746b43d --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt @@ -0,0 +1,26 @@ +* Central Interrupt Unit + +Properties: +- compatible: "cavium,octeon-3860-ciu" + + Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is the bank within + the CIU and may have a value of 0 or 1. The second cell is the bit + within the bank and may have a value between 0 and 63. + +Example: + interrupt-controller@1070000000000 { + compatible = "cavium,octeon-3860-ciu"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Controller register (0 or 1) + * 2) Bit within the register (0..63) + */ + #interrupt-cells = <2>; + reg = <0x10700 0x00000000 0x0 0x7000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu2.txt b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt new file mode 100644 index 000000000000..0ec7ba8bbbcb --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit + +Properties: +- compatible: "cavium,octeon-6880-ciu2" + + Compatibility with 68XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is the bank within + the CIU and may have a value between 0 and 63. The second cell is + the bit within the bank and may also have a value between 0 and 63. + +Example: + interrupt-controller@1070100000000 { + compatible = "cavium,octeon-6880-ciu2"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Controller register (0..63) + * 2) Bit within the register (0..63) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10701 0x00000000 0x0 0x4000000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt new file mode 100644 index 000000000000..cb4291e3b1d1 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt @@ -0,0 +1,21 @@ +* DMA Engine. + +The Octeon DMA Engine transfers between the Boot Bus and main memory. +The DMA Engine will be refered to by phandle by any device that is +connected to it. + +Properties: +- compatible: "cavium,octeon-5750-bootbus-dma" + + Compatibility with all cn52XX, cn56XX and cn6XXX SOCs. + +- reg: The base address of the DMA Engine's register bank. + +- interrupts: A single interrupt specifier. + +Example: + dma0: dma-engine@1180000000100 { + compatible = "cavium,octeon-5750-bootbus-dma"; + reg = <0x11800 0x00000100 0x0 0x8>; + interrupts = <0 63>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt new file mode 100644 index 000000000000..aa66b9b8d801 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt @@ -0,0 +1,46 @@ +* UCTL USB controller glue + +Properties: +- compatible: "cavium,octeon-6335-uctl" + + Compatibility with all cn6XXX SOCs. + +- reg: The base address of the UCTL register bank. + +- #address-cells: Must be <2>. + +- #size-cells: Must be <2>. + +- ranges: Empty to signify direct mapping of the children. + +- refclk-frequency: A single cell containing the reference clock + frequency in Hz. + +- refclk-type: A string describing the reference clock connection + either "crystal" or "external". + +Example: + uctl@118006f000000 { + compatible = "cavium,octeon-6335-uctl"; + reg = <0x11800 0x6f000000 0x0 0x100>; + ranges; /* Direct mapping */ + #address-cells = <2>; + #size-cells = <2>; + /* 12MHz, 24MHz and 48MHz allowed */ + refclk-frequency = <24000000>; + /* Either "crystal" or "external" */ + refclk-type = "crystal"; + + ehci@16f0000000000 { + compatible = "cavium,octeon-6335-ehci","usb-ehci"; + reg = <0x16f00 0x00000000 0x0 0x100>; + interrupts = <0 56>; + big-endian-regs; + }; + ohci@16f0000000400 { + compatible = "cavium,octeon-6335-ohci","usb-ohci"; + reg = <0x16f00 0x00000400 0x0 0x100>; + interrupts = <0 56>; + big-endian-regs; + }; + }; diff --git a/Documentation/devicetree/bindings/misc/at25.txt b/Documentation/devicetree/bindings/misc/at25.txt new file mode 100644 index 000000000000..ab3c327929dd --- /dev/null +++ b/Documentation/devicetree/bindings/misc/at25.txt @@ -0,0 +1,21 @@ +Atmel AT25 eeprom + +Required properties: +- compatible : "atmel,at25". +- reg : chip select number +- spi-max-frequency : max spi frequency to use + +- at25,byte-len : total eeprom size in bytes +- at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h +- at25,page-size : size of the eeprom page + +Examples: +at25@0 { + compatible = "atmel,at25"; + reg = <0> + spi-max-frequency = <5000000>; + + at25,byte-len = <0x8000>; + at25,addr-mode = <2>; + at25,page-size = <64>; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 70cd49b1caa8..1dd622546d06 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -10,8 +10,8 @@ Required properties: - compatible : Should be "fsl,<chip>-esdhc" Optional properties: -- fsl,cd-internal : Indicate to use controller internal card detection -- fsl,wp-internal : Indicate to use controller internal write protection +- fsl,cd-controller : Indicate to use controller internal card detection +- fsl,wp-controller : Indicate to use controller internal write protection Examples: @@ -19,8 +19,8 @@ esdhc@70004000 { compatible = "fsl,imx51-esdhc"; reg = <0x70004000 0x4000>; interrupts = <1>; - fsl,cd-internal; - fsl,wp-internal; + fsl,cd-controller; + fsl,wp-controller; }; esdhc@70008000 { diff --git a/Documentation/devicetree/bindings/mtd/orion-nand.txt b/Documentation/devicetree/bindings/mtd/orion-nand.txt index b2356b7d2fa4..2d6ab660e603 100644 --- a/Documentation/devicetree/bindings/mtd/orion-nand.txt +++ b/Documentation/devicetree/bindings/mtd/orion-nand.txt @@ -1,7 +1,7 @@ NAND support for Marvell Orion SoC platforms Required properties: -- compatible : "mrvl,orion-nand". +- compatible : "marvell,orion-nand". - reg : Base physical address of the NAND and length of memory mapped region @@ -24,7 +24,7 @@ nand@f4000000 { ale = <1>; bank-width = <1>; chip-delay = <25>; - compatible = "mrvl,orion-nand"; + compatible = "marvell,orion-nand"; reg = <0xf4000000 0x400>; partition@0 { diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt new file mode 100644 index 000000000000..04cb7491d232 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt @@ -0,0 +1,27 @@ +* System Management Interface (SMI) / MDIO + +Properties: +- compatible: "cavium,octeon-3860-mdio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the MDIO bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@1180000001800 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001800 0x0 0x40>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt new file mode 100644 index 000000000000..5da628db68bf --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mix.txt @@ -0,0 +1,39 @@ +* MIX Ethernet controller. + +Properties: +- compatible: "cavium,octeon-5750-mix" + + Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX + devices. + +- reg: The base addresses of four separate register banks. The first + bank contains the MIX registers. The second bank the corresponding + AGL registers. The third bank are the AGL registers shared by all + MIX devices present. The fourth bank is the AGL_PRT_CTL shared by + all MIX devices present. + +- cell-index: A single cell specifying which portion of the shared + register banks corresponds to this MIX device. + +- interrupts: Two interrupt specifiers. The first is the MIX + interrupt routing and the second the routing for the AGL interrupts. + +- mac-address: Optional, the MAC address to assign to the device. + +- local-mac-address: Optional, the MAC address to assign to the device + if mac-address is not specified. + +- phy-handle: Optional, a phandle for the PHY device connected to this device. + +Example: + ethernet@1070000100800 { + compatible = "cavium,octeon-5750-mix"; + reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */ + <0x11800 0xE0000800 0x0 0x300>, /* AGL */ + <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */ + <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */ + cell-index = <1>; + interrupts = <1 18>, < 1 46>; + local-mac-address = [ 00 0f b7 10 63 54 ]; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt new file mode 100644 index 000000000000..d4c53ba04b3b --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -0,0 +1,98 @@ +* PIP Ethernet nexus. + +The PIP Ethernet nexus can control several data packet input/output +devices. The devices have a two level grouping scheme. There may be +several interfaces, and each interface may have several ports. These +ports might be an individual Ethernet PHY. + + +Properties for the PIP nexus: +- compatible: "cavium,octeon-3860-pip" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the PIP's register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP interfaces which is a child the PIP nexus: +- compatible: "cavium,octeon-3860-pip-interface" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The interface number. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP port which is a child the PIP interface: +- compatible: "cavium,octeon-3860-pip-port" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The port number within the interface group. + +- mac-address: Optional, the MAC address to assign to the device. + +- local-mac-address: Optional, the MAC address to assign to the device + if mac-address is not specified. + +- phy-handle: Optional, a phandle for the PHY device connected to this device. + +Example: + + pip@11800a0000000 { + compatible = "cavium,octeon-3860-pip"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0xa0000000 0x0 0x2000>; + + interface@0 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 60 ]; + phy-handle = <&phy2>; + }; + ethernet@1 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x1>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 61 ]; + phy-handle = <&phy3>; + }; + ethernet@2 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x2>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 62 ]; + phy-handle = <&phy4>; + }; + ethernet@3 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x3>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 63 ]; + phy-handle = <&phy5>; + }; + }; + + interface@1 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 64 ]; + phy-handle = <&phy6>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt new file mode 100644 index 000000000000..cfe1db3bb6e9 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt @@ -0,0 +1,12 @@ +LPC32XX PWM controller + +Required properties: +- compatible: should be "nxp,lpc3220-pwm" +- reg: physical base address and length of the controller's registers + +Examples: + +pwm@0x4005C000 { + compatible = "nxp,lpc3220-pwm"; + reg = <0x4005C000 0x8>; +}; diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt new file mode 100644 index 000000000000..b16f4a57d111 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt @@ -0,0 +1,17 @@ +Freescale MXS PWM controller + +Required properties: +- compatible: should be "fsl,imx23-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the duty cycle in nanoseconds. +- fsl,pwm-number: the number of PWM devices + +Example: + +pwm: pwm@80064000 { + compatible = "fsl,imx28-pwm", "fsl,imx23-pwm"; + reg = <0x80064000 2000>; + #pwm-cells = <2>; + fsl,pwm-number = <8>; +}; diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt new file mode 100644 index 000000000000..bbbeedb4ec05 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -0,0 +1,18 @@ +Tegra SoC PWFM controller + +Required properties: +- compatible: should be one of: + - "nvidia,tegra20-pwm" + - "nvidia,tegra30-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: On Tegra the number of cells used to specify a PWM is 2. The + first cell specifies the per-chip index of the PWM to use and the second + cell is the duty cycle in nanoseconds. + +Example: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt new file mode 100644 index 000000000000..73ec962bfe8c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -0,0 +1,57 @@ +Specifying PWM information for devices +====================================== + +1) PWM user nodes +----------------- + +PWM users should specify a list of PWM devices that they want to use +with a property containing a 'pwm-list': + + pwm-list ::= <single-pwm> [pwm-list] + single-pwm ::= <pwm-phandle> <pwm-specifier> + pwm-phandle : phandle to PWM controller node + pwm-specifier : array of #pwm-cells specifying the given PWM + (controller specific) + +PWM properties should be named "pwms". The exact meaning of each pwms +property must be documented in the device tree binding for each device. +An optional property "pwm-names" may contain a list of strings to label +each of the PWM devices listed in the "pwms" property. If no "pwm-names" +property is given, the name of the user node will be used as fallback. + +Drivers for devices that use more than a single PWM device can use the +"pwm-names" property to map the name of the PWM device requested by the +pwm_get() call to an index into the list given by the "pwms" property. + +The following example could be used to describe a PWM-based backlight +device: + + pwm: pwm { + #pwm-cells = <2>; + }; + + [...] + + bl: backlight { + pwms = <&pwm 0 5000000>; + pwm-names = "backlight"; + }; + +pwm-specifier typically encodes the chip-relative PWM number and the PWM +period in nanoseconds. Note that in the example above, specifying the +"pwm-names" is redundant because the name "backlight" would be used as +fallback anyway. + +2) PWM controller nodes +----------------------- + +PWM controller nodes must specify the number of cells used for the +specifier using the '#pwm-cells' property. + +An example PWM controller might look like this: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index d156e1b5db12..da80c2ae0915 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -9,9 +9,9 @@ Required properties: - regulators: list of regulators provided by this controller, must have property "regulator-compatible" to match their hardware counterparts: sm[0-2], ldo[0-9] and ldo_rtc -- sm0-supply: The input supply for the SM0. -- sm1-supply: The input supply for the SM1. -- sm2-supply: The input supply for the SM2. +- vin-sm0-supply: The input supply for the SM0. +- vin-sm1-supply: The input supply for the SM1. +- vin-sm2-supply: The input supply for the SM2. - vinldo01-supply: The input supply for the LDO1 and LDO2 - vinldo23-supply: The input supply for the LDO2 and LDO3 - vinldo4-supply: The input supply for the LDO4 @@ -30,9 +30,9 @@ Example: #gpio-cells = <2>; gpio-controller; - sm0-supply = <&some_reg>; - sm1-supply = <&some_reg>; - sm2-supply = <&some_reg>; + vin-sm0-supply = <&some_reg>; + vin-sm1-supply = <&some_reg>; + vin-sm2-supply = <&some_reg>; vinldo01-supply = <...>; vinldo23-supply = <...>; vinldo4-supply = <...>; diff --git a/Documentation/devicetree/bindings/serial/cavium-uart.txt b/Documentation/devicetree/bindings/serial/cavium-uart.txt new file mode 100644 index 000000000000..87a6c375cd44 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cavium-uart.txt @@ -0,0 +1,19 @@ +* Universal Asynchronous Receiver/Transmitter (UART) + +- compatible: "cavium,octeon-3860-uart" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the UART register bank. + +- interrupts: A single interrupt specifier. + +- current-speed: Optional, the current bit rate in bits per second. + +Example: + uart1: serial@1180000000c00 { + compatible = "cavium,octeon-3860-uart","ns16550"; + reg = <0x11800 0x00000c00 0x0 0x400>; + current-speed = <115200>; + interrupts = <0 35>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt new file mode 100644 index 000000000000..a3ff50fc76fb --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -0,0 +1,19 @@ +Marvell Orion SPI device + +Required properties: +- compatible : should be "marvell,orion-spi". +- reg : offset and length of the register set for the device +- cell-index : Which of multiple SPI controllers is this. +Optional properties: +- interrupts : Is currently not used. + +Example: + spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = <0x10600 0x28>; + interrupts = <23>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/thermal/spear-thermal.txt b/Documentation/devicetree/bindings/thermal/spear-thermal.txt new file mode 100644 index 000000000000..93e3b67c102d --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/spear-thermal.txt @@ -0,0 +1,14 @@ +* SPEAr Thermal + +Required properties: +- compatible : "st,thermal-spear1340" +- reg : Address range of the thermal registers +- st,thermal-flags: flags used to enable thermal sensor + +Example: + + thermal@fc000000 { + compatible = "st,thermal-spear1340"; + reg = <0xfc000000 0x1000>; + st,thermal-flags = <0x7000>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index b8b27b0aca10..0847fdeee11a 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -9,6 +9,7 @@ Required properties: - "ns16750" - "ns16850" - "nvidia,tegra20-uart" + - "nxp,lpc3220-uart" - "ibm,qpace-nwp-serial" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt new file mode 100644 index 000000000000..2c290418bb2d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -0,0 +1,18 @@ +* Freescale i.MX ci13xxx usb controllers + +Required properties: +- compatible: Should be "fsl,imx27-usb" +- reg: Should contain registers location and length +- interrupts: Should contain controller interrupt + +Optional properties: +- fsl,usbphy: phandler of usb phy that connects to the only one port +- vbus-supply: regulator for vbus + +Examples: +usb@02184000 { /* USB OTG */ + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184000 0x200>; + interrupts = <0 43 0x04>; + fsl,usbphy = <&usbphy1>; +}; diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt new file mode 100644 index 000000000000..5835b27146ea --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt @@ -0,0 +1,13 @@ +* Freescale MXS USB Phy Device + +Required properties: +- compatible: Should be "fsl,imx23-usbphy" +- reg: Should contain registers location and length +- interrupts: Should contain phy interrupt + +Example: +usbphy1: usbphy@020c9000 { + compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; + reg = <0x020c9000 0x1000>; + interrupts = <0 44 0x04>; +}; diff --git a/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt new file mode 100644 index 000000000000..1e4fc727f3b1 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt @@ -0,0 +1,28 @@ +pwm-backlight bindings + +Required properties: + - compatible: "pwm-backlight" + - pwms: OF device-tree PWM specification (see PWM binding[0]) + - brightness-levels: Array of distinct brightness levels. Typically these + are in the range from 0 to 255, but any range starting at 0 will do. + The actual brightness level (PWM duty cycle) will be interpolated + from these values. 0 means a 0% duty cycle (darkest/off), while the + last value in the array represents a 100% duty cycle (brightest). + - default-brightness-level: the default brightness level (index into the + array defined by the "brightness-levels" property) + +Optional properties: + - pwm-names: a list of names for the PWM devices specified in the + "pwms" property (see PWM binding[0]) + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Example: + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 5000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/marvel.txt b/Documentation/devicetree/bindings/watchdog/marvel.txt new file mode 100644 index 000000000000..0b2503ab0a05 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/marvel.txt @@ -0,0 +1,14 @@ +* Marvell Orion Watchdog Time + +Required Properties: + +- Compatibility : "marvell,orion-wdt" +- reg : Address of the timer registers + +Example: + + wdt@20300 { + compatible = "marvell,orion-wdt"; + reg = <0x20300 0x28>; + status = "okay"; + }; |