summaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt44
-rw-r--r--Documentation/devicetree/bindings/mfd/max8998.txt119
-rw-r--r--Documentation/devicetree/bindings/mfd/twl4030-power.txt28
-rw-r--r--Documentation/devicetree/bindings/regulator/twl-regulator.txt26
-rw-r--r--Documentation/devicetree/bindings/usb/twlxxxx-usb.txt2
5 files changed, 205 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
new file mode 100644
index 000000000000..491c97b78384
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
@@ -0,0 +1,44 @@
+* TI - TSC ADC (Touschscreen and analog digital converter)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties:
+- child "tsc"
+ ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
+ support on the platform.
+ ti,x-plate-resistance: X plate resistance
+ ti,coordiante-readouts: The sequencer supports a total of 16
+ programmable steps each step is used to
+ read a single coordinate. A single
+ readout is enough but multiple reads can
+ increase the quality.
+ A value of 5 means, 5 reads for X, 5 for
+ Y and 2 for Z (always). This utilises 12
+ of the 16 software steps available. The
+ remaining 4 can be used by the ADC.
+ ti,wire-config: Different boards could have a different order for
+ connecting wires on touchscreen. We need to provide an
+ 8 bit number where in the 1st four bits represent the
+ analog lines and the next 4 bits represent positive/
+ negative terminal on that input line. Notations to
+ represent the input lines and terminals resoectively
+ is as follows:
+ AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+ XP = 0, XN = 1, YP = 2, YN = 3.
+- child "adc"
+ ti,adc-channels: List of analog inputs available for ADC.
+ AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+
+Example:
+ tscadc: tscadc@44e0d000 {
+ compatible = "ti,am3359-tscadc";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,coordiante-readouts = <5>;
+ ti,wire-config = <0x00 0x11 0x22 0x33>;
+ };
+
+ adc {
+ ti,adc-channels = <4 5 6 7>;
+ };
+ }
diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt
new file mode 100644
index 000000000000..23a3650ff2a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max8998.txt
@@ -0,0 +1,119 @@
+* Maxim MAX8998, National/TI LP3974 multi-function device
+
+The Maxim MAX8998 is a multi-function device which includes voltage/current
+regulators, real time clock, battery charging controller and several
+other sub-blocks. It is interfaced using an I2C interface. Each sub-block
+is addressed by the host system using different i2c slave address.
+
+PMIC sub-block
+--------------
+
+The PMIC sub-block contains a number of voltage and current regulators,
+with controllable parameters and dynamic voltage scaling capability.
+In addition, it includes a real time clock and battery charging controller
+as well. It is accessible at I2C address 0x66.
+
+Required properties:
+- compatible: Should be one of the following:
+ - "maxim,max8998" for Maxim MAX8998
+ - "national,lp3974" or "ti,lp3974" for National/TI LP3974.
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+ the interrupts from MAX8998 are routed to.
+- interrupts: Interrupt specifiers for two interrupt sources.
+ - First interrupt specifier is for main interrupt.
+ - Second interrupt specifier is for power-on/-off interrupt.
+- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used
+ for buck 1 dvs. The format of the gpio specifier depends on the gpio
+ controller.
+- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used
+ for buck 2 dvs. The format of the gpio specifier depends on the gpio
+ controller.
+- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from
+ the possible 4 options selectable by the dvs gpios. The value of this
+ property should be 0, 1, 2 or 3. If not specified or out of range,
+ a default value of 0 is taken.
+- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from
+ the possible 2 options selectable by the dvs gpios. The value of this
+ property should be 0 or 1. If not specified or out of range, a default
+ value of 0 is taken.
+- max8998,pmic-buck-voltage-lock: If present, disallows changing of
+ preprogrammed buck dvfs voltages.
+
+Additional properties required if max8998,pmic-buck1-dvs-gpios is defined:
+- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts
+ for buck1 regulator that can be selected using dvs gpio.
+
+Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
+- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
+ for buck2 regulator that can be selected using dvs gpio.
+
+Regulators: All the regulators of MAX8998 to be instantiated shall be
+listed in a child node named 'regulators'. Each regulator is represented
+by a child node of the 'regulators' node.
+
+ regulator-name {
+ /* standard regulator bindings here */
+ };
+
+Following regulators of the MAX8998 PMIC block are supported. Note that
+the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK
+number as described in MAX8998 datasheet.
+
+ - LDOn
+ - valid values for n are 2 to 17
+ - Example: LDO2, LDO10, LDO17
+ - BUCKn
+ - valid values for n are 1 to 4.
+ - Example: BUCK1, BUCK2, BUCK3, BUCK4
+
+ - ENVICHG: Battery Charging Current Monitor Output. This is a fixed
+ voltage type regulator
+
+ - ESAFEOUT1: (ldo19)
+ - ESAFEOUT2: (ld020)
+
+Standard regulator bindings are used inside regulator subnodes. Check
+ Documentation/devicetree/bindings/regulator/regulator.txt
+for more details.
+
+Example:
+
+ pmic@66 {
+ compatible = "maxim,max8998-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&wakeup_eint>;
+ interrupts = <4 0>, <3 0>;
+
+ /* Buck 1 DVS settings */
+ max8998,pmic-buck1-default-dvs-idx = <0>;
+ max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
+ <&gpx0 1 1 0 0>; /* SET2 */
+ max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+ <1000000>, <950000>;
+
+ /* Buck 2 DVS settings */
+ max8998,pmic-buck2-default-dvs-idx = <0>;
+ max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
+ max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
+
+ /* Regulators to instantiate */
+ regulators {
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_ALIVE_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_ARM_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
new file mode 100644
index 000000000000..8e15ec35ac99
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
@@ -0,0 +1,28 @@
+Texas Instruments TWL family (twl4030) reset and power management module
+
+The power management module inside the TWL family provides several facilities
+to control the power resources, including power scripts. For now, the
+binding only supports the complete shutdown of the system after poweroff.
+
+Required properties:
+- compatible : must be "ti,twl4030-power"
+
+Optional properties:
+- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or
+ SLEEP-to-OFF transition when the system poweroffs.
+
+Example:
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+
+ twl_power: power {
+ compatible = "ti,twl4030-power";
+ ti,use_poweroff;
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
index 658749b90b97..75b0c1669504 100644
--- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
@@ -18,20 +18,20 @@ For twl6030 regulators/LDOs
- "ti,twl6030-vdd1" for VDD1 SMPS
- "ti,twl6030-vdd2" for VDD2 SMPS
- "ti,twl6030-vdd3" for VDD3 SMPS
-For twl6025 regulators/LDOs
+For twl6032 regulators/LDOs
- compatible:
- - "ti,twl6025-ldo1" for LDO1 LDO
- - "ti,twl6025-ldo2" for LDO2 LDO
- - "ti,twl6025-ldo3" for LDO3 LDO
- - "ti,twl6025-ldo4" for LDO4 LDO
- - "ti,twl6025-ldo5" for LDO5 LDO
- - "ti,twl6025-ldo6" for LDO6 LDO
- - "ti,twl6025-ldo7" for LDO7 LDO
- - "ti,twl6025-ldoln" for LDOLN LDO
- - "ti,twl6025-ldousb" for LDOUSB LDO
- - "ti,twl6025-smps3" for SMPS3 SMPS
- - "ti,twl6025-smps4" for SMPS4 SMPS
- - "ti,twl6025-vio" for VIO SMPS
+ - "ti,twl6032-ldo1" for LDO1 LDO
+ - "ti,twl6032-ldo2" for LDO2 LDO
+ - "ti,twl6032-ldo3" for LDO3 LDO
+ - "ti,twl6032-ldo4" for LDO4 LDO
+ - "ti,twl6032-ldo5" for LDO5 LDO
+ - "ti,twl6032-ldo6" for LDO6 LDO
+ - "ti,twl6032-ldo7" for LDO7 LDO
+ - "ti,twl6032-ldoln" for LDOLN LDO
+ - "ti,twl6032-ldousb" for LDOUSB LDO
+ - "ti,twl6032-smps3" for SMPS3 SMPS
+ - "ti,twl6032-smps4" for SMPS4 SMPS
+ - "ti,twl6032-vio" for VIO SMPS
For twl4030 regulators/LDOs
- compatible:
- "ti,twl4030-vaux1" for VAUX1 LDO
diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
index 36b9aede3f40..0aee0ad3f035 100644
--- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -8,7 +8,7 @@ TWL6030 USB COMPARATOR
usb interrupt number that raises VBUS interrupts when the controller has to
act as device
- usb-supply : phandle to the regulator device tree node. It should be vusb
- if it is twl6030 or ldousb if it is twl6025 subclass.
+ if it is twl6030 or ldousb if it is twl6032 subclass.
twl6030-usb {
compatible = "ti,twl6030-usb";