summaryrefslogtreecommitdiff
path: root/arch/arm/mach-omap2/devices.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/mach-omap2/devices.c')
-rw-r--r--arch/arm/mach-omap2/devices.c293
1 files changed, 33 insertions, 260 deletions
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index d216976988d7..2cb720b5b12e 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -478,117 +478,10 @@ static inline void omap_init_aes(void) { }
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
-#define MMCHS_SYSCONFIG 0x0010
-#define MMCHS_SYSCONFIG_SWRESET (1 << 1)
-#define MMCHS_SYSSTATUS 0x0014
-#define MMCHS_SYSSTATUS_RESETDONE (1 << 0)
-
-static struct platform_device dummy_pdev = {
- .dev = {
- .bus = &platform_bus_type,
- },
-};
-
-/**
- * omap_hsmmc_reset() - Full reset of each HS-MMC controller
- *
- * Ensure that each MMC controller is fully reset. Controllers
- * left in an unknown state (by bootloader) may prevent retention
- * or OFF-mode. This is especially important in cases where the
- * MMC driver is not enabled, _or_ built as a module.
- *
- * In order for reset to work, interface, functional and debounce
- * clocks must be enabled. The debounce clock comes from func_32k_clk
- * and is not under SW control, so we only enable i- and f-clocks.
- **/
-static void __init omap_hsmmc_reset(void)
-{
- u32 i, nr_controllers;
- struct clk *iclk, *fclk;
-
- if (cpu_is_omap242x())
- return;
-
- nr_controllers = cpu_is_omap44xx() ? OMAP44XX_NR_MMC :
- (cpu_is_omap34xx() ? OMAP34XX_NR_MMC : OMAP24XX_NR_MMC);
-
- for (i = 0; i < nr_controllers; i++) {
- u32 v, base = 0;
- struct device *dev = &dummy_pdev.dev;
-
- switch (i) {
- case 0:
- base = OMAP2_MMC1_BASE;
- break;
- case 1:
- base = OMAP2_MMC2_BASE;
- break;
- case 2:
- base = OMAP3_MMC3_BASE;
- break;
- case 3:
- if (!cpu_is_omap44xx())
- return;
- base = OMAP4_MMC4_BASE;
- break;
- case 4:
- if (!cpu_is_omap44xx())
- return;
- base = OMAP4_MMC5_BASE;
- break;
- }
-
- if (cpu_is_omap44xx())
- base += OMAP4_MMC_REG_OFFSET;
-
- dummy_pdev.id = i;
- dev_set_name(&dummy_pdev.dev, "mmci-omap-hs.%d", i);
- iclk = clk_get(dev, "ick");
- if (IS_ERR(iclk))
- goto err1;
- if (clk_enable(iclk))
- goto err2;
-
- fclk = clk_get(dev, "fck");
- if (IS_ERR(fclk))
- goto err3;
- if (clk_enable(fclk))
- goto err4;
-
- omap_writel(MMCHS_SYSCONFIG_SWRESET, base + MMCHS_SYSCONFIG);
- v = omap_readl(base + MMCHS_SYSSTATUS);
- while (!(omap_readl(base + MMCHS_SYSSTATUS) &
- MMCHS_SYSSTATUS_RESETDONE))
- cpu_relax();
-
- clk_disable(fclk);
- clk_put(fclk);
- clk_disable(iclk);
- clk_put(iclk);
- }
- return;
-
-err4:
- clk_put(fclk);
-err3:
- clk_disable(iclk);
-err2:
- clk_put(iclk);
-err1:
- printk(KERN_WARNING "%s: Unable to enable clocks for MMC%d, "
- "cannot reset.\n", __func__, i);
-}
-#else
-static inline void omap_hsmmc_reset(void) {}
-#endif
-
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
- defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-
-static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
- int controller_nr)
+static inline void omap242x_mmc_mux(struct omap_mmc_platform_data
+ *mmc_controller)
{
if ((mmc_controller->slots[0].switch_pin > 0) && \
(mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
@@ -599,163 +492,44 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
OMAP_PIN_INPUT_PULLUP);
- if (cpu_is_omap2420() && controller_nr == 0) {
- omap_mux_init_signal("sdmmc_cmd", 0);
- omap_mux_init_signal("sdmmc_clki", 0);
- omap_mux_init_signal("sdmmc_clko", 0);
- omap_mux_init_signal("sdmmc_dat0", 0);
- omap_mux_init_signal("sdmmc_dat_dir0", 0);
- omap_mux_init_signal("sdmmc_cmd_dir", 0);
- if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
- omap_mux_init_signal("sdmmc_dat1", 0);
- omap_mux_init_signal("sdmmc_dat2", 0);
- omap_mux_init_signal("sdmmc_dat3", 0);
- omap_mux_init_signal("sdmmc_dat_dir1", 0);
- omap_mux_init_signal("sdmmc_dat_dir2", 0);
- omap_mux_init_signal("sdmmc_dat_dir3", 0);
- }
-
- /*
- * Use internal loop-back in MMC/SDIO Module Input Clock
- * selection
- */
- if (mmc_controller->slots[0].internal_clock) {
- u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- v |= (1 << 24);
- omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
- }
+ omap_mux_init_signal("sdmmc_cmd", 0);
+ omap_mux_init_signal("sdmmc_clki", 0);
+ omap_mux_init_signal("sdmmc_clko", 0);
+ omap_mux_init_signal("sdmmc_dat0", 0);
+ omap_mux_init_signal("sdmmc_dat_dir0", 0);
+ omap_mux_init_signal("sdmmc_cmd_dir", 0);
+ if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
+ omap_mux_init_signal("sdmmc_dat1", 0);
+ omap_mux_init_signal("sdmmc_dat2", 0);
+ omap_mux_init_signal("sdmmc_dat3", 0);
+ omap_mux_init_signal("sdmmc_dat_dir1", 0);
+ omap_mux_init_signal("sdmmc_dat_dir2", 0);
+ omap_mux_init_signal("sdmmc_dat_dir3", 0);
}
- if (cpu_is_omap34xx()) {
- if (controller_nr == 0) {
- omap_mux_init_signal("sdmmc1_clk",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_cmd",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_dat0",
- OMAP_PIN_INPUT_PULLUP);
- if (mmc_controller->slots[0].caps &
- (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
- omap_mux_init_signal("sdmmc1_dat1",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_dat2",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_dat3",
- OMAP_PIN_INPUT_PULLUP);
- }
- if (mmc_controller->slots[0].caps &
- MMC_CAP_8_BIT_DATA) {
- omap_mux_init_signal("sdmmc1_dat4",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_dat5",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_dat6",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc1_dat7",
- OMAP_PIN_INPUT_PULLUP);
- }
- }
- if (controller_nr == 1) {
- /* MMC2 */
- omap_mux_init_signal("sdmmc2_clk",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_cmd",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_dat0",
- OMAP_PIN_INPUT_PULLUP);
-
- /*
- * For 8 wire configurations, Lines DAT4, 5, 6 and 7 need to be muxed
- * in the board-*.c files
- */
- if (mmc_controller->slots[0].caps &
- (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
- omap_mux_init_signal("sdmmc2_dat1",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_dat2",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_dat3",
- OMAP_PIN_INPUT_PULLUP);
- }
- if (mmc_controller->slots[0].caps &
- MMC_CAP_8_BIT_DATA) {
- omap_mux_init_signal("sdmmc2_dat4.sdmmc2_dat4",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_dat5.sdmmc2_dat5",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_dat6.sdmmc2_dat6",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("sdmmc2_dat7.sdmmc2_dat7",
- OMAP_PIN_INPUT_PULLUP);
- }
- }
-
- /*
- * For MMC3 the pins need to be muxed in the board-*.c files
- */
+ /*
+ * Use internal loop-back in MMC/SDIO Module Input Clock
+ * selection
+ */
+ if (mmc_controller->slots[0].internal_clock) {
+ u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
+ v |= (1 << 24);
+ omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
}
}
-void __init omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
- int nr_controllers)
+void __init omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
{
- int i;
- char *name;
+ char *name = "mmci-omap";
- for (i = 0; i < nr_controllers; i++) {
- unsigned long base, size;
- unsigned int irq = 0;
-
- if (!mmc_data[i])
- continue;
-
- omap2_mmc_mux(mmc_data[i], i);
+ if (!mmc_data[0]) {
+ pr_err("%s fails: Incomplete platform data\n", __func__);
+ return;
+ }
- switch (i) {
- case 0:
- base = OMAP2_MMC1_BASE;
- irq = INT_24XX_MMC_IRQ;
- break;
- case 1:
- base = OMAP2_MMC2_BASE;
- irq = INT_24XX_MMC2_IRQ;
- break;
- case 2:
- if (!cpu_is_omap44xx() && !cpu_is_omap34xx())
- return;
- base = OMAP3_MMC3_BASE;
- irq = INT_34XX_MMC3_IRQ;
- break;
- case 3:
- if (!cpu_is_omap44xx())
- return;
- base = OMAP4_MMC4_BASE;
- irq = OMAP44XX_IRQ_MMC4;
- break;
- case 4:
- if (!cpu_is_omap44xx())
- return;
- base = OMAP4_MMC5_BASE;
- irq = OMAP44XX_IRQ_MMC5;
- break;
- default:
- continue;
- }
-
- if (cpu_is_omap2420()) {
- size = OMAP2420_MMC_SIZE;
- name = "mmci-omap";
- } else if (cpu_is_omap44xx()) {
- if (i < 3)
- irq += OMAP44XX_IRQ_GIC_START;
- size = OMAP4_HSMMC_SIZE;
- name = "mmci-omap-hs";
- } else {
- size = OMAP3_HSMMC_SIZE;
- name = "mmci-omap-hs";
- }
- omap_mmc_add(name, i, base, size, irq, mmc_data[i]);
- };
+ omap242x_mmc_mux(mmc_data[0]);
+ omap_mmc_add(name, 0, OMAP2_MMC1_BASE, OMAP2420_MMC_SIZE,
+ INT_24XX_MMC_IRQ, mmc_data[0]);
}
#endif
@@ -829,7 +603,6 @@ static int __init omap2_init_devices(void)
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
- omap_hsmmc_reset();
omap_init_audio();
omap_init_camera();
omap_init_mbox();
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-26 22:22:29 +0000