summaryrefslogtreecommitdiff
path: root/drivers/clocksource/cadence_ttc_timer.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/clocksource/cadence_ttc_timer.c')
-rw-r--r--drivers/clocksource/cadence_ttc_timer.c121
1 files changed, 86 insertions, 35 deletions
diff --git a/drivers/clocksource/cadence_ttc_timer.c b/drivers/clocksource/cadence_ttc_timer.c
index 63f176de0d02..49fbe2847c84 100644
--- a/drivers/clocksource/cadence_ttc_timer.c
+++ b/drivers/clocksource/cadence_ttc_timer.c
@@ -16,6 +16,7 @@
*/
#include <linux/clk.h>
+#include <linux/clk-provider.h>
#include <linux/interrupt.h>
#include <linux/clockchips.h>
#include <linux/of_address.h>
@@ -52,6 +53,8 @@
#define TTC_CNT_CNTRL_DISABLE_MASK 0x1
#define TTC_CLK_CNTRL_CSRC_MASK (1 << 5) /* clock source */
+#define TTC_CLK_CNTRL_PSV_MASK 0x1e
+#define TTC_CLK_CNTRL_PSV_SHIFT 1
/*
* Setup the timers to use pre-scaling, using a fixed value for now that will
@@ -63,6 +66,8 @@
#define CLK_CNTRL_PRESCALE_EN 1
#define CNT_CNTRL_RESET (1 << 4)
+#define MAX_F_ERR 50
+
/**
* struct ttc_timer - This definition defines local timer structure
*
@@ -82,6 +87,8 @@ struct ttc_timer {
container_of(x, struct ttc_timer, clk_rate_change_nb)
struct ttc_timer_clocksource {
+ u32 scale_clk_ctrl_reg_old;
+ u32 scale_clk_ctrl_reg_new;
struct ttc_timer ttc;
struct clocksource cs;
};
@@ -229,32 +236,89 @@ static int ttc_rate_change_clocksource_cb(struct notifier_block *nb,
struct ttc_timer_clocksource, ttc);
switch (event) {
- case POST_RATE_CHANGE:
+ case PRE_RATE_CHANGE:
+ {
+ u32 psv;
+ unsigned long factor, rate_low, rate_high;
+
+ if (ndata->new_rate > ndata->old_rate) {
+ factor = DIV_ROUND_CLOSEST(ndata->new_rate,
+ ndata->old_rate);
+ rate_low = ndata->old_rate;
+ rate_high = ndata->new_rate;
+ } else {
+ factor = DIV_ROUND_CLOSEST(ndata->old_rate,
+ ndata->new_rate);
+ rate_low = ndata->new_rate;
+ rate_high = ndata->old_rate;
+ }
+
+ if (!is_power_of_2(factor))
+ return NOTIFY_BAD;
+
+ if (abs(rate_high - (factor * rate_low)) > MAX_F_ERR)
+ return NOTIFY_BAD;
+
+ factor = __ilog2_u32(factor);
+
/*
- * Do whatever is necessary to maintain a proper time base
- *
- * I cannot find a way to adjust the currently used clocksource
- * to the new frequency. __clocksource_updatefreq_hz() sounds
- * good, but does not work. Not sure what's that missing.
- *
- * This approach works, but triggers two clocksource switches.
- * The first after unregister to clocksource jiffies. And
- * another one after the register to the newly registered timer.
- *
- * Alternatively we could 'waste' another HW timer to ping pong
- * between clock sources. That would also use one register and
- * one unregister call, but only trigger one clocksource switch
- * for the cost of another HW timer used by the OS.
+ * store timer clock ctrl register so we can restore it in case
+ * of an abort.
*/
- clocksource_unregister(&ttccs->cs);
- clocksource_register_hz(&ttccs->cs,
- ndata->new_rate / PRESCALE);
- /* fall through */
- case PRE_RATE_CHANGE:
+ ttccs->scale_clk_ctrl_reg_old =
+ __raw_readl(ttccs->ttc.base_addr +
+ TTC_CLK_CNTRL_OFFSET);
+
+ psv = (ttccs->scale_clk_ctrl_reg_old &
+ TTC_CLK_CNTRL_PSV_MASK) >>
+ TTC_CLK_CNTRL_PSV_SHIFT;
+ if (ndata->new_rate < ndata->old_rate)
+ psv -= factor;
+ else
+ psv += factor;
+
+ /* prescaler within legal range? */
+ if (psv & ~(TTC_CLK_CNTRL_PSV_MASK >> TTC_CLK_CNTRL_PSV_SHIFT))
+ return NOTIFY_BAD;
+
+ ttccs->scale_clk_ctrl_reg_new = ttccs->scale_clk_ctrl_reg_old &
+ ~TTC_CLK_CNTRL_PSV_MASK;
+ ttccs->scale_clk_ctrl_reg_new |= psv << TTC_CLK_CNTRL_PSV_SHIFT;
+
+
+ /* scale down: adjust divider in post-change notification */
+ if (ndata->new_rate < ndata->old_rate)
+ return NOTIFY_DONE;
+
+ /* scale up: adjust divider now - before frequency change */
+ __raw_writel(ttccs->scale_clk_ctrl_reg_new,
+ ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
+ break;
+ }
+ case POST_RATE_CHANGE:
+ /* scale up: pre-change notification did the adjustment */
+ if (ndata->new_rate > ndata->old_rate)
+ return NOTIFY_OK;
+
+ /* scale down: adjust divider now - after frequency change */
+ __raw_writel(ttccs->scale_clk_ctrl_reg_new,
+ ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
+ break;
+
case ABORT_RATE_CHANGE:
+ /* we have to undo the adjustment in case we scale up */
+ if (ndata->new_rate < ndata->old_rate)
+ return NOTIFY_OK;
+
+ /* restore original register value */
+ __raw_writel(ttccs->scale_clk_ctrl_reg_old,
+ ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
+ /* fall through */
default:
return NOTIFY_DONE;
}
+
+ return NOTIFY_DONE;
}
static void __init ttc_setup_clocksource(struct clk *clk, void __iomem *base)
@@ -321,25 +385,12 @@ static int ttc_rate_change_clockevent_cb(struct notifier_block *nb,
switch (event) {
case POST_RATE_CHANGE:
- {
- unsigned long flags;
-
- /*
- * clockevents_update_freq should be called with IRQ disabled on
- * the CPU the timer provides events for. The timer we use is
- * common to both CPUs, not sure if we need to run on both
- * cores.
- */
- local_irq_save(flags);
- clockevents_update_freq(&ttcce->ce,
- ndata->new_rate / PRESCALE);
- local_irq_restore(flags);
-
/* update cached frequency */
ttc->freq = ndata->new_rate;
+ clockevents_update_freq(&ttcce->ce, ndata->new_rate / PRESCALE);
+
/* fall through */
- }
case PRE_RATE_CHANGE:
case ABORT_RATE_CHANGE:
default: