diff options
Diffstat (limited to 'drivers/gpu/drm/i915/i915_reg.h')
| -rw-r--r-- | drivers/gpu/drm/i915/i915_reg.h | 93 |
1 files changed, 84 insertions, 9 deletions
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 1687edf68795..7214c852df99 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -214,7 +214,7 @@ #define I830_FENCE_SIZE_BITS(size) ((ffs((size) >> 19) - 1) << 8) #define I830_FENCE_PITCH_SHIFT 4 #define I830_FENCE_REG_VALID (1<<0) -#define I915_FENCE_MAX_PITCH_VAL 0x10 +#define I915_FENCE_MAX_PITCH_VAL 4 #define I830_FENCE_MAX_PITCH_VAL 6 #define I830_FENCE_MAX_SIZE_VAL (1<<8) @@ -307,6 +307,70 @@ #define LM_BURST_LENGTH 0x00000700 #define LM_FIFO_WATERMARK 0x0000001F #define MI_ARB_STATE 0x020e4 /* 915+ only */ +#define MI_ARB_MASK_SHIFT 16 /* shift for enable bits */ + +/* Make render/texture TLB fetches lower priorty than associated data + * fetches. This is not turned on by default + */ +#define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15) + +/* Isoch request wait on GTT enable (Display A/B/C streams). + * Make isoch requests stall on the TLB update. May cause + * display underruns (test mode only) + */ +#define MI_ARB_ISOCH_WAIT_GTT (1 << 14) + +/* Block grant count for isoch requests when block count is + * set to a finite value. + */ +#define MI_ARB_BLOCK_GRANT_MASK (3 << 12) +#define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */ +#define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */ +#define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */ +#define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */ + +/* Enable render writes to complete in C2/C3/C4 power states. + * If this isn't enabled, render writes are prevented in low + * power states. That seems bad to me. + */ +#define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11) + +/* This acknowledges an async flip immediately instead + * of waiting for 2TLB fetches. + */ +#define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10) + +/* Enables non-sequential data reads through arbiter + */ +#define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9) + +/* Disable FSB snooping of cacheable write cycles from binner/render + * command stream + */ +#define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8) + +/* Arbiter time slice for non-isoch streams */ +#define MI_ARB_TIME_SLICE_MASK (7 << 5) +#define MI_ARB_TIME_SLICE_1 (0 << 5) +#define MI_ARB_TIME_SLICE_2 (1 << 5) +#define MI_ARB_TIME_SLICE_4 (2 << 5) +#define MI_ARB_TIME_SLICE_6 (3 << 5) +#define MI_ARB_TIME_SLICE_8 (4 << 5) +#define MI_ARB_TIME_SLICE_10 (5 << 5) +#define MI_ARB_TIME_SLICE_14 (6 << 5) +#define MI_ARB_TIME_SLICE_16 (7 << 5) + +/* Low priority grace period page size */ +#define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */ +#define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4) + +/* Disable display A/B trickle feed */ +#define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2) + +/* Set display plane priority */ +#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */ +#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */ + #define CACHE_MODE_0 0x02120 /* 915+ only */ #define CM0_MASK_SHIFT 16 #define CM0_IZ_OPT_DISABLE (1<<6) @@ -329,6 +393,7 @@ #define FBC_CTL_PERIODIC (1<<30) #define FBC_CTL_INTERVAL_SHIFT (16) #define FBC_CTL_UNCOMPRESSIBLE (1<<14) +#define FBC_C3_IDLE (1<<13) #define FBC_CTL_STRIDE_SHIFT (5) #define FBC_CTL_FENCENO (1<<0) #define FBC_COMMAND 0x0320c @@ -405,6 +470,13 @@ # define GPIO_DATA_VAL_IN (1 << 12) # define GPIO_DATA_PULLUP_DISABLE (1 << 13) +#define GMBUS0 0x5100 +#define GMBUS1 0x5104 +#define GMBUS2 0x5108 +#define GMBUS3 0x510c +#define GMBUS4 0x5110 +#define GMBUS5 0x5120 + /* * Clock control & power management */ @@ -863,14 +935,6 @@ #define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2) #define CRT_HOTPLUG_MASK (0x3fc) /* Bits 9-2 */ #define CRT_FORCE_HOTPLUG_MASK 0xfffffe1f -#define HOTPLUG_EN_MASK (HDMIB_HOTPLUG_INT_EN | \ - HDMIC_HOTPLUG_INT_EN | \ - HDMID_HOTPLUG_INT_EN | \ - SDVOB_HOTPLUG_INT_EN | \ - SDVOC_HOTPLUG_INT_EN | \ - TV_HOTPLUG_INT_EN | \ - CRT_HOTPLUG_INT_EN) - #define PORT_HOTPLUG_STAT 0x61114 #define HDMIB_HOTPLUG_INT_STATUS (1 << 29) @@ -968,6 +1032,8 @@ #define LVDS_PORT_EN (1 << 31) /* Selects pipe B for LVDS data. Must be set on pre-965. */ #define LVDS_PIPEB_SELECT (1 << 30) +/* LVDS dithering flag on 965/g4x platform */ +#define LVDS_ENABLE_DITHER (1 << 25) /* Enable border for unscaled (or aspect-scaled) display */ #define LVDS_BORDER_ENABLE (1 << 15) /* @@ -1737,6 +1803,8 @@ /* Display & cursor control */ +/* dithering flag on Ironlake */ +#define PIPE_ENABLE_DITHER (1 << 4) /* Pipe A */ #define PIPEADSL 0x70000 #define PIPEACONF 0x70008 @@ -2157,6 +2225,13 @@ #define PCH_GPIOE 0xc5020 #define PCH_GPIOF 0xc5024 +#define PCH_GMBUS0 0xc5100 +#define PCH_GMBUS1 0xc5104 +#define PCH_GMBUS2 0xc5108 +#define PCH_GMBUS3 0xc510c +#define PCH_GMBUS4 0xc5110 +#define PCH_GMBUS5 0xc5120 + #define PCH_DPLL_A 0xc6014 #define PCH_DPLL_B 0xc6018 |