summaryrefslogtreecommitdiff
path: root/drivers/mtd/nand/r852.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mtd/nand/r852.h')
-rw-r--r--drivers/mtd/nand/r852.h163
1 files changed, 163 insertions, 0 deletions
diff --git a/drivers/mtd/nand/r852.h b/drivers/mtd/nand/r852.h
new file mode 100644
index 000000000000..8096cc280c73
--- /dev/null
+++ b/drivers/mtd/nand/r852.h
@@ -0,0 +1,163 @@
+/*
+ * Copyright © 2009 - Maxim Levitsky
+ * driver for Ricoh xD readers
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/completion.h>
+#include <linux/workqueue.h>
+#include <linux/mtd/nand.h>
+#include <linux/spinlock.h>
+
+
+/* nand interface + ecc
+ byte write/read does one cycle on nand data lines.
+ dword write/read does 4 cycles
+ if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads
+ results of ecc correction, if DMA read was done before.
+ If write was done two dword reads read generated ecc checksums
+*/
+#define R852_DATALINE 0x00
+
+/* control register */
+#define R852_CTL 0x04
+#define R852_CTL_COMMAND 0x01 /* send command (#CLE)*/
+#define R852_CTL_DATA 0x02 /* read/write data (#ALE)*/
+#define R852_CTL_ON 0x04 /* only seem to controls the hd led, */
+ /* but has to be set on start...*/
+#define R852_CTL_RESET 0x08 /* unknown, set only on start once*/
+#define R852_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/
+#define R852_CTL_ECC_ENABLE 0x20 /* enable ecc engine */
+#define R852_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/
+#define R852_CTL_WRITE 0x80 /* set when performing writes (#WP) */
+
+/* card detection status */
+#define R852_CARD_STA 0x05
+
+#define R852_CARD_STA_CD 0x01 /* state of #CD line, same as 0x04 */
+#define R852_CARD_STA_RO 0x02 /* card is readonly */
+#define R852_CARD_STA_PRESENT 0x04 /* card is present (#CD) */
+#define R852_CARD_STA_ABSENT 0x08 /* card is absent */
+#define R852_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */
+
+/* card detection irq status & enable*/
+#define R852_CARD_IRQ_STA 0x06 /* IRQ status */
+#define R852_CARD_IRQ_ENABLE 0x07 /* IRQ enable */
+
+#define R852_CARD_IRQ_CD 0x01 /* fire when #CD lights, same as 0x04*/
+#define R852_CARD_IRQ_REMOVE 0x04 /* detect card removal */
+#define R852_CARD_IRQ_INSERT 0x08 /* detect card insert */
+#define R852_CARD_IRQ_UNK1 0x10 /* unknown */
+#define R852_CARD_IRQ_GENABLE 0x80 /* general enable */
+#define R852_CARD_IRQ_MASK 0x1D
+
+
+
+/* hardware enable */
+#define R852_HW 0x08
+#define R852_HW_ENABLED 0x01 /* hw enabled */
+#define R852_HW_UNKNOWN 0x80
+
+
+/* dma capabilities */
+#define R852_DMA_CAP 0x09
+#define R852_SMBIT 0x20 /* if set with bit #6 or bit #7, then */
+ /* hw is smartmedia */
+#define R852_DMA1 0x40 /* if set w/bit #7, dma is supported */
+#define R852_DMA2 0x80 /* if set w/bit #6, dma is supported */
+
+
+/* physical DMA address - 32 bit value*/
+#define R852_DMA_ADDR 0x0C
+
+
+/* dma settings */
+#define R852_DMA_SETTINGS 0x10
+#define R852_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */
+#define R852_DMA_READ 0x02 /* 0 = write, 1 = read */
+#define R852_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */
+
+/* dma IRQ status */
+#define R852_DMA_IRQ_STA 0x14
+
+/* dma IRQ enable */
+#define R852_DMA_IRQ_ENABLE 0x18
+
+#define R852_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */
+#define R852_DMA_IRQ_ERROR 0x02 /* error did happen */
+#define R852_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */
+#define R852_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */
+
+
+/* ECC syndrome format - read from reg #0 will return two copies of these for
+ each half of the page.
+ first byte is error byte location, and second, bit location + flags */
+#define R852_ECC_ERR_BIT_MSK 0x07 /* error bit location */
+#define R852_ECC_CORRECT 0x10 /* no errors - (guessed) */
+#define R852_ECC_CORRECTABLE 0x20 /* correctable error exist */
+#define R852_ECC_FAIL 0x40 /* non correctable error detected */
+
+#define R852_DMA_LEN 512
+
+#define DMA_INTERNAL 0
+#define DMA_MEMORY 1
+
+struct r852_device {
+ void __iomem *mmio; /* mmio */
+ struct mtd_info *mtd; /* mtd backpointer */
+ struct nand_chip *chip; /* nand chip backpointer */
+ struct pci_dev *pci_dev; /* pci backpointer */
+
+ /* dma area */
+ dma_addr_t phys_dma_addr; /* bus address of buffer*/
+ struct completion dma_done; /* data transfer done */
+
+ dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */
+ uint8_t *bounce_buffer; /* virtual address of bounce buffer */
+
+ int dma_dir; /* 1 = read, 0 = write */
+ int dma_stage; /* 0 - idle, 1 - first step,
+ 2 - second step */
+
+ int dma_state; /* 0 = internal, 1 = memory */
+ int dma_error; /* dma errors */
+ int dma_usable; /* is it possible to use dma */
+
+ /* card status area */
+ struct delayed_work card_detect_work;
+ struct workqueue_struct *card_workqueue;
+ int card_registred; /* card registered with mtd */
+ int card_detected; /* card detected in slot */
+ int card_unstable; /* whenever the card is inserted,
+ is not known yet */
+ int readonly; /* card is readonly */
+ int sm; /* Is card smartmedia */
+
+ /* interrupt handling */
+ spinlock_t irqlock; /* IRQ protecting lock */
+ int irq; /* irq num */
+ int insuspend; /* device is suspended */
+
+ /* misc */
+ void *tmp_buffer; /* temporary buffer */
+ uint8_t ctlreg; /* cached contents of control reg */
+};
+
+#define DRV_NAME "r852"
+
+
+#define dbg(format, ...) \
+ if (debug) \
+ printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)
+
+#define dbg_verbose(format, ...) \
+ if (debug > 1) \
+ printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)
+
+
+#define message(format, ...) \
+ printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__)