diff options
Diffstat (limited to 'drivers/net/wireless/ath6kl/Kconfig')
| -rw-r--r-- | drivers/net/wireless/ath6kl/Kconfig | 152 |
1 files changed, 152 insertions, 0 deletions
diff --git a/drivers/net/wireless/ath6kl/Kconfig b/drivers/net/wireless/ath6kl/Kconfig new file mode 100644 index 000000000000..fa4c2447f80e --- /dev/null +++ b/drivers/net/wireless/ath6kl/Kconfig @@ -0,0 +1,152 @@ +config ATH6K_LEGACY + tristate "Atheros AR600x support (non mac80211)" + depends on MMC + depends on WLAN + select WIRELESS_EXT + select WEXT_SPY + select WEXT_PRIV + help + This module adds support for wireless adapters based on Atheros AR600x chipset running over SDIO. If you choose to build it as a module, it will be called ath6kl. + +choice + prompt "AR600x Board Data Configuration" + depends on ATH6K_LEGACY + default AR600x_SD31_XXX + help + Select the appropriate board data template from the list below that matches your AR600x based reference design. + +config AR600x_SD31_XXX + bool "SD31-xxx" + help + Board Data file for a standard SD31 reference design (File: bdata.SD31.bin) + +config AR600x_WB31_XXX + bool "WB31-xxx" + help + Board Data file for a standard WB31 (BT/WiFi) reference design (File: bdata.WB31.bin) + +config AR600x_SD32_XXX + bool "SD32-xxx" + help + Board Data file for a standard SD32 (5GHz) reference design (File: bdata.SD32.bin) + +config AR600x_CUSTOM_XXX + bool "CUSTOM-xxx" + help + Board Data file for a custom reference design (File: should be named as bdata.CUSTOM.bin) +endchoice + +config ATH6KL_ENABLE_COEXISTENCE + bool "BT Coexistence support" + depends on ATH6K_LEGACY + help + Enables WLAN/BT coexistence support. Select the apprpriate configuration from below. + +choice + prompt "Front-End Antenna Configuration" + depends on ATH6KL_ENABLE_COEXISTENCE + default AR600x_DUAL_ANTENNA + help + Select the appropriate configuration from the list below that matches your AR600x based reference design. + +config AR600x_DUAL_ANTENNA + bool "Dual Antenna" + help + Dual Antenna Design + +config AR600x_SINGLE_ANTENNA + bool "Single Antenna" + help + Single Antenna Design +endchoice + +choice + prompt "Collocated Bluetooth Type" + depends on ATH6KL_ENABLE_COEXISTENCE + default AR600x_BT_AR3001 + help + Select the appropriate configuration from the list below that matches your AR600x based reference design. + +config AR600x_BT_QCOM + bool "Qualcomm BTS4020X" + help + Qualcomm BT (3 Wire PTA) + +config AR600x_BT_CSR + bool "CSR BC06" + help + CSR BT (3 Wire PTA) + +config AR600x_BT_AR3001 + bool "Atheros AR3001" + help + Atheros BT (3 Wire PTA) +endchoice + +config ATH6KL_HCI_BRIDGE + bool "HCI over SDIO support" + depends on ATH6K_LEGACY + help + Enables BT over SDIO. Applicable only for combo designs (eg: WB31) + +config ATH6KL_CONFIG_GPIO_BT_RESET + bool "Configure BT Reset GPIO" + depends on ATH6KL_HCI_BRIDGE + help + Configure a WLAN GPIO for use with BT. + +config AR600x_BT_RESET_PIN + int "GPIO" + depends on ATH6KL_CONFIG_GPIO_BT_RESET + default 22 + help + WLAN GPIO to be used for resetting BT + +config ATH6KL_CFG80211 + bool "CFG80211 support" + depends on ATH6K_LEGACY + help + Enables support for CFG80211 APIs + +config ATH6KL_HTC_RAW_INTERFACE + bool "RAW HTC support" + depends on ATH6K_LEGACY + help + Enables raw HTC interface. Allows application to directly talk to the HTC interface via the ioctl interface + +config ATH6KL_VIRTUAL_SCATTER_GATHER + bool "Virtual Scatter-Gather support" + depends on ATH6K_LEGACY + help + Enables virtual scatter gather support for the hardware that does not support it natively. + +config ATH6KL_DEBUG + bool "Debug support" + depends on ATH6K_LEGACY + help + Enables debug support + +config ATH6KL_ENABLE_HOST_DEBUG + bool "Host Debug support" + depends on ATH6KL_DEBUG + help + Enables debug support in the driver + +config ATH6KL_ENABLE_TARGET_DEBUG_PRINTS + bool "Target Debug support - Enable UART prints" + depends on ATH6KL_DEBUG + help + Enables uart prints + +config AR600x_DEBUG_UART_TX_PIN + int "GPIO" + depends on ATH6KL_ENABLE_TARGET_DEBUG_PRINTS + default 8 + help + WLAN GPIO to be used for Debug UART (Tx) + +config ATH6KL_DISABLE_TARGET_DBGLOGS + bool "Target Debug support - Disable Debug logs" + depends on ATH6KL_DEBUG + help + Enables debug logs |