summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/iwlwifi/iwl-commands.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-commands.h')
-rw-r--r--drivers/net/wireless/iwlwifi/iwl-commands.h647
1 files changed, 6 insertions, 641 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-commands.h b/drivers/net/wireless/iwlwifi/iwl-commands.h
index ca42ffa63ed7..a1a5c1b23096 100644
--- a/drivers/net/wireless/iwlwifi/iwl-commands.h
+++ b/drivers/net/wireless/iwlwifi/iwl-commands.h
@@ -5,7 +5,7 @@
*
* GPL LICENSE SUMMARY
*
- * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
@@ -30,7 +30,7 @@
*
* BSD LICENSE
*
- * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
@@ -103,9 +103,7 @@ enum {
REPLY_WEPKEY = 0x20,
/* RX, TX, LEDs */
- REPLY_3945_RX = 0x1b, /* 3945 only */
REPLY_TX = 0x1c,
- REPLY_RATE_SCALE = 0x47, /* 3945 only */
REPLY_LEDS_CMD = 0x48,
REPLY_TX_LINK_QUALITY_CMD = 0x4e, /* for 4965 and up */
@@ -229,7 +227,7 @@ struct iwl_cmd_header {
* There is one exception: uCode sets bit 15 when it originates
* the response/notification, i.e. when the response/notification
* is not a direct response to a command sent by the driver. For
- * example, uCode issues REPLY_3945_RX when it sends a received frame
+ * example, uCode issues REPLY_RX when it sends a received frame
* to the driver; it is not a direct response to any driver command.
*
* The Linux driver uses the following format:
@@ -249,36 +247,6 @@ struct iwl_cmd_header {
/**
- * struct iwl3945_tx_power
- *
- * Used in REPLY_TX_PWR_TABLE_CMD, REPLY_SCAN_CMD, REPLY_CHANNEL_SWITCH
- *
- * Each entry contains two values:
- * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
- * linear value that multiplies the output of the digital signal processor,
- * before being sent to the analog radio.
- * 2) Radio gain. This sets the analog gain of the radio Tx path.
- * It is a coarser setting, and behaves in a logarithmic (dB) fashion.
- *
- * Driver obtains values from struct iwl3945_tx_power power_gain_table[][].
- */
-struct iwl3945_tx_power {
- u8 tx_gain; /* gain for analog radio */
- u8 dsp_atten; /* gain for DSP */
-} __packed;
-
-/**
- * struct iwl3945_power_per_rate
- *
- * Used in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
- */
-struct iwl3945_power_per_rate {
- u8 rate; /* plcp */
- struct iwl3945_tx_power tpc;
- u8 reserved;
-} __packed;
-
-/**
* iwlagn rate_n_flags bit fields
*
* rate_n_flags format is used in following iwlagn commands:
@@ -324,6 +292,8 @@ struct iwl3945_power_per_rate {
#define RATE_MCS_SPATIAL_MSK 0x18
#define RATE_MCS_HT_DUP_POS 5
#define RATE_MCS_HT_DUP_MSK 0x20
+/* Both legacy and HT use bits 7:0 as the CCK/OFDM rate or HT MCS */
+#define RATE_MCS_RATE_MSK 0xff
/* Bit 8: (1) HT format, (0) legacy format in bits 7:0 */
#define RATE_MCS_FLAGS_POS 8
@@ -375,30 +345,6 @@ struct iwl3945_power_per_rate {
#define IWL_PWR_CCK_ENTRIES 2
/**
- * union iwl4965_tx_power_dual_stream
- *
- * Host format used for REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
- * Use __le32 version (struct tx_power_dual_stream) when building command.
- *
- * Driver provides radio gain and DSP attenuation settings to device in pairs,
- * one value for each transmitter chain. The first value is for transmitter A,
- * second for transmitter B.
- *
- * For SISO bit rates, both values in a pair should be identical.
- * For MIMO rates, one value may be different from the other,
- * in order to balance the Tx output between the two transmitters.
- *
- * See more details in doc for TXPOWER in iwl-4965-hw.h.
- */
-union iwl4965_tx_power_dual_stream {
- struct {
- u8 radio_tx_gain[2];
- u8 dsp_predis_atten[2];
- } s;
- u32 dw;
-};
-
-/**
* struct tx_power_dual_stream
*
* Table entries in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
@@ -410,15 +356,6 @@ struct tx_power_dual_stream {
} __packed;
/**
- * struct iwl4965_tx_power_db
- *
- * Entire table within REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
- */
-struct iwl4965_tx_power_db {
- struct tx_power_dual_stream power_tbl[POWER_TABLE_NUM_ENTRIES];
-} __packed;
-
-/**
* Command REPLY_TX_POWER_DBM_CMD = 0x98
* struct iwlagn_tx_power_dbm_cmd
*/
@@ -451,54 +388,6 @@ struct iwl_tx_ant_config_cmd {
#define UCODE_VALID_OK cpu_to_le32(0x1)
#define INITIALIZE_SUBTYPE (9)
-/*
- * ("Initialize") REPLY_ALIVE = 0x1 (response only, not a command)
- *
- * uCode issues this "initialize alive" notification once the initialization
- * uCode image has completed its work, and is ready to load the runtime image.
- * This is the *first* "alive" notification that the driver will receive after
- * rebooting uCode; the "initialize" alive is indicated by subtype field == 9.
- *
- * See comments documenting "BSM" (bootstrap state machine).
- *
- * For 4965, this notification contains important calibration data for
- * calculating txpower settings:
- *
- * 1) Power supply voltage indication. The voltage sensor outputs higher
- * values for lower voltage, and vice verse.
- *
- * 2) Temperature measurement parameters, for each of two channel widths
- * (20 MHz and 40 MHz) supported by the radios. Temperature sensing
- * is done via one of the receiver chains, and channel width influences
- * the results.
- *
- * 3) Tx gain compensation to balance 4965's 2 Tx chains for MIMO operation,
- * for each of 5 frequency ranges.
- */
-struct iwl_init_alive_resp {
- u8 ucode_minor;
- u8 ucode_major;
- __le16 reserved1;
- u8 sw_rev[8];
- u8 ver_type;
- u8 ver_subtype; /* "9" for initialize alive */
- __le16 reserved2;
- __le32 log_event_table_ptr;
- __le32 error_event_table_ptr;
- __le32 timestamp;
- __le32 is_valid;
-
- /* calibration values from "initialize" uCode */
- __le32 voltage; /* signed, higher value is lower voltage */
- __le32 therm_r1[2]; /* signed, 1st for normal, 2nd for HT40 */
- __le32 therm_r2[2]; /* signed */
- __le32 therm_r3[2]; /* signed */
- __le32 therm_r4[2]; /* signed */
- __le32 tx_atten[5][2]; /* signed MIMO gain comp, 5 freq groups,
- * 2 Tx chains */
-} __packed;
-
-
/**
* REPLY_ALIVE = 0x1 (response only, not a command)
*
@@ -722,46 +611,6 @@ enum {
* regardless of whether RXON_FILTER_ASSOC_MSK is set.
*/
-struct iwl3945_rxon_cmd {
- u8 node_addr[6];
- __le16 reserved1;
- u8 bssid_addr[6];
- __le16 reserved2;
- u8 wlap_bssid_addr[6];
- __le16 reserved3;
- u8 dev_type;
- u8 air_propagation;
- __le16 reserved4;
- u8 ofdm_basic_rates;
- u8 cck_basic_rates;
- __le16 assoc_id;
- __le32 flags;
- __le32 filter_flags;
- __le16 channel;
- __le16 reserved5;
-} __packed;
-
-struct iwl4965_rxon_cmd {
- u8 node_addr[6];
- __le16 reserved1;
- u8 bssid_addr[6];
- __le16 reserved2;
- u8 wlap_bssid_addr[6];
- __le16 reserved3;
- u8 dev_type;
- u8 air_propagation;
- __le16 rx_chain;
- u8 ofdm_basic_rates;
- u8 cck_basic_rates;
- __le16 assoc_id;
- __le32 flags;
- __le32 filter_flags;
- __le16 channel;
- u8 ofdm_ht_single_stream_basic_rates;
- u8 ofdm_ht_dual_stream_basic_rates;
-} __packed;
-
-/* 5000 HW just extend this command */
struct iwl_rxon_cmd {
u8 node_addr[6];
__le16 reserved1;
@@ -789,25 +638,6 @@ struct iwl_rxon_cmd {
/*
* REPLY_RXON_ASSOC = 0x11 (command, has simple generic response)
*/
-struct iwl3945_rxon_assoc_cmd {
- __le32 flags;
- __le32 filter_flags;
- u8 ofdm_basic_rates;
- u8 cck_basic_rates;
- __le16 reserved;
-} __packed;
-
-struct iwl4965_rxon_assoc_cmd {
- __le32 flags;
- __le32 filter_flags;
- u8 ofdm_basic_rates;
- u8 cck_basic_rates;
- u8 ofdm_ht_single_stream_basic_rates;
- u8 ofdm_ht_dual_stream_basic_rates;
- __le16 rx_chain_select_flags;
- __le16 reserved;
-} __packed;
-
struct iwl5000_rxon_assoc_cmd {
__le32 flags;
__le32 filter_flags;
@@ -843,26 +673,6 @@ struct iwl_rxon_time_cmd {
/*
* REPLY_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
*/
-struct iwl3945_channel_switch_cmd {
- u8 band;
- u8 expect_beacon;
- __le16 channel;
- __le32 rxon_flags;
- __le32 rxon_filter_flags;
- __le32 switch_time;
- struct iwl3945_power_per_rate power[IWL_MAX_RATES];
-} __packed;
-
-struct iwl4965_channel_switch_cmd {
- u8 band;
- u8 expect_beacon;
- __le16 channel;
- __le32 rxon_flags;
- __le32 rxon_filter_flags;
- __le32 switch_time;
- struct iwl4965_tx_power_db tx_power;
-} __packed;
-
/**
* struct iwl5000_channel_switch_cmd
* @band: 0- 5.2GHz, 1- 2.4GHz
@@ -976,15 +786,10 @@ struct iwl_qosparam_cmd {
#define IWL_AP_ID 0
#define IWL_AP_ID_PAN 1
#define IWL_STA_ID 2
-#define IWL3945_BROADCAST_ID 24
-#define IWL3945_STATION_COUNT 25
-#define IWL4965_BROADCAST_ID 31
-#define IWL4965_STATION_COUNT 32
#define IWLAGN_PAN_BCAST_ID 14
#define IWLAGN_BROADCAST_ID 15
#define IWLAGN_STATION_COUNT 16
-#define IWL_STATION_COUNT 32 /* MAX(3945,4965)*/
#define IWL_INVALID_STATION 255
#define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2)
@@ -1032,16 +837,6 @@ struct iwl_qosparam_cmd {
* combined with Traffic ID (QOS priority), in format used by Tx Scheduler */
#define BUILD_RAxTID(sta_id, tid) (((sta_id) << 4) + (tid))
-struct iwl4965_keyinfo {
- __le16 key_flags;
- u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
- u8 reserved1;
- __le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
- u8 key_offset;
- u8 reserved2;
- u8 key[16]; /* 16-byte unicast decryption key */
-} __packed;
-
/* agn */
struct iwl_keyinfo {
__le16 key_flags;
@@ -1083,7 +878,6 @@ struct sta_id_modify {
* with info on security keys, aggregation parameters, and Tx rates for
* initial Tx attempt and any retries (agn devices uses
* REPLY_TX_LINK_QUALITY_CMD,
- * 3945 uses REPLY_RATE_SCALE to set up rate tables).
*
* REPLY_ADD_STA sets up the table entry for one station, either creating
* a new entry, or modifying a pre-existing one.
@@ -1103,72 +897,6 @@ struct sta_id_modify {
* entries for all STAs in network, starting with index IWL_STA_ID.
*/
-struct iwl3945_addsta_cmd {
- u8 mode; /* 1: modify existing, 0: add new station */
- u8 reserved[3];
- struct sta_id_modify sta;
- struct iwl4965_keyinfo key;
- __le32 station_flags; /* STA_FLG_* */
- __le32 station_flags_msk; /* STA_FLG_* */
-
- /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
- * corresponding to bit (e.g. bit 5 controls TID 5).
- * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
- __le16 tid_disable_tx;
-
- __le16 rate_n_flags;
-
- /* TID for which to add block-ack support.
- * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
- u8 add_immediate_ba_tid;
-
- /* TID for which to remove block-ack support.
- * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
- u8 remove_immediate_ba_tid;
-
- /* Starting Sequence Number for added block-ack support.
- * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
- __le16 add_immediate_ba_ssn;
-} __packed;
-
-struct iwl4965_addsta_cmd {
- u8 mode; /* 1: modify existing, 0: add new station */
- u8 reserved[3];
- struct sta_id_modify sta;
- struct iwl4965_keyinfo key;
- __le32 station_flags; /* STA_FLG_* */
- __le32 station_flags_msk; /* STA_FLG_* */
-
- /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
- * corresponding to bit (e.g. bit 5 controls TID 5).
- * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
- __le16 tid_disable_tx;
-
- __le16 reserved1;
-
- /* TID for which to add block-ack support.
- * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
- u8 add_immediate_ba_tid;
-
- /* TID for which to remove block-ack support.
- * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
- u8 remove_immediate_ba_tid;
-
- /* Starting Sequence Number for added block-ack support.
- * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
- __le16 add_immediate_ba_ssn;
-
- /*
- * Number of packets OK to transmit to station even though
- * it is asleep -- used to synchronise PS-poll and u-APSD
- * responses while ucode keeps track of STA sleep state.
- */
- __le16 sleep_tx_count;
-
- __le16 reserved2;
-} __packed;
-
-/* agn */
struct iwl_addsta_cmd {
u8 mode; /* 1: modify existing, 0: add new station */
u8 reserved[3];
@@ -1337,62 +1065,6 @@ struct iwl_wep_cmd {
#define RX_MPDU_RES_STATUS_DEC_DONE_MSK (0x800)
-struct iwl3945_rx_frame_stats {
- u8 phy_count;
- u8 id;
- u8 rssi;
- u8 agc;
- __le16 sig_avg;
- __le16 noise_diff;
- u8 payload[0];
-} __packed;
-
-struct iwl3945_rx_frame_hdr {
- __le16 channel;
- __le16 phy_flags;
- u8 reserved1;
- u8 rate;
- __le16 len;
- u8 payload[0];
-} __packed;
-
-struct iwl3945_rx_frame_end {
- __le32 status;
- __le64 timestamp;
- __le32 beacon_timestamp;
-} __packed;
-
-/*
- * REPLY_3945_RX = 0x1b (response only, not a command)
- *
- * NOTE: DO NOT dereference from casts to this structure
- * It is provided only for calculating minimum data set size.
- * The actual offsets of the hdr and end are dynamic based on
- * stats.phy_count
- */
-struct iwl3945_rx_frame {
- struct iwl3945_rx_frame_stats stats;
- struct iwl3945_rx_frame_hdr hdr;
- struct iwl3945_rx_frame_end end;
-} __packed;
-
-#define IWL39_RX_FRAME_SIZE (4 + sizeof(struct iwl3945_rx_frame))
-
-/* Fixed (non-configurable) rx data from phy */
-
-#define IWL49_RX_RES_PHY_CNT 14
-#define IWL49_RX_PHY_FLAGS_ANTENNAE_OFFSET (4)
-#define IWL49_RX_PHY_FLAGS_ANTENNAE_MASK (0x70)
-#define IWL49_AGC_DB_MASK (0x3f80) /* MASK(7,13) */
-#define IWL49_AGC_DB_POS (7)
-struct iwl4965_rx_non_cfg_phy {
- __le16 ant_selection; /* ant A bit 4, ant B bit 5, ant C bit 6 */
- __le16 agc_info; /* agc code 0:6, agc dB 7:13, reserved 14:15 */
- u8 rssi_info[6]; /* we use even entries, 0/2/4 for A/B/C rssi */
- u8 pad[0];
-} __packed;
-
-
#define IWLAGN_RX_RES_PHY_CNT 8
#define IWLAGN_RX_RES_AGC_IDX 1
#define IWLAGN_RX_RES_RSSI_AB_IDX 2
@@ -1576,80 +1248,6 @@ struct iwl_rx_mpdu_res_start {
* REPLY_TX = 0x1c (command)
*/
-struct iwl3945_tx_cmd {
- /*
- * MPDU byte count:
- * MAC header (24/26/30/32 bytes) + 2 bytes pad if 26/30 header size,
- * + 8 byte IV for CCM or TKIP (not used for WEP)
- * + Data payload
- * + 8-byte MIC (not used for CCM/WEP)
- * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
- * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
- * Range: 14-2342 bytes.
- */
- __le16 len;
-
- /*
- * MPDU or MSDU byte count for next frame.
- * Used for fragmentation and bursting, but not 11n aggregation.
- * Same as "len", but for next frame. Set to 0 if not applicable.
- */
- __le16 next_frame_len;
-
- __le32 tx_flags; /* TX_CMD_FLG_* */
-
- u8 rate;
-
- /* Index of recipient station in uCode's station table */
- u8 sta_id;
- u8 tid_tspec;
- u8 sec_ctl;
- u8 key[16];
- union {
- u8 byte[8];
- __le16 word[4];
- __le32 dw[2];
- } tkip_mic;
- __le32 next_frame_info;
- union {
- __le32 life_time;
- __le32 attempt;
- } stop_time;
- u8 supp_rates[2];
- u8 rts_retry_limit; /*byte 50 */
- u8 data_retry_limit; /*byte 51 */
- union {
- __le16 pm_frame_timeout;
- __le16 attempt_duration;
- } timeout;
-
- /*
- * Duration of EDCA burst Tx Opportunity, in 32-usec units.
- * Set this if txop time is not specified by HCCA protocol (e.g. by AP).
- */
- __le16 driver_txop;
-
- /*
- * MAC header goes here, followed by 2 bytes padding if MAC header
- * length is 26 or 30 bytes, followed by payload data
- */
- u8 payload[0];
- struct ieee80211_hdr hdr[0];
-} __packed;
-
-/*
- * REPLY_TX = 0x1c (response)
- */
-struct iwl3945_tx_resp {
- u8 failure_rts;
- u8 failure_frame;
- u8 bt_kill_count;
- u8 rate;
- __le32 wireless_media_time;
- __le32 status; /* TX status */
-} __packed;
-
-
/*
* 4965 uCode updates these Tx attempt count values in host DRAM.
* Used for managing Tx retries when expecting block-acks.
@@ -1740,54 +1338,6 @@ struct iwl_tx_cmd {
struct ieee80211_hdr hdr[0];
} __packed;
-/* TX command response is sent after *3945* transmission attempts.
- *
- * NOTES:
- *
- * TX_STATUS_FAIL_NEXT_FRAG
- *
- * If the fragment flag in the MAC header for the frame being transmitted
- * is set and there is insufficient time to transmit the next frame, the
- * TX status will be returned with 'TX_STATUS_FAIL_NEXT_FRAG'.
- *
- * TX_STATUS_FIFO_UNDERRUN
- *
- * Indicates the host did not provide bytes to the FIFO fast enough while
- * a TX was in progress.
- *
- * TX_STATUS_FAIL_MGMNT_ABORT
- *
- * This status is only possible if the ABORT ON MGMT RX parameter was
- * set to true with the TX command.
- *
- * If the MSB of the status parameter is set then an abort sequence is
- * required. This sequence consists of the host activating the TX Abort
- * control line, and then waiting for the TX Abort command response. This
- * indicates that a the device is no longer in a transmit state, and that the
- * command FIFO has been cleared. The host must then deactivate the TX Abort
- * control line. Receiving is still allowed in this case.
- */
-enum {
- TX_3945_STATUS_SUCCESS = 0x01,
- TX_3945_STATUS_DIRECT_DONE = 0x02,
- TX_3945_STATUS_FAIL_SHORT_LIMIT = 0x82,
- TX_3945_STATUS_FAIL_LONG_LIMIT = 0x83,
- TX_3945_STATUS_FAIL_FIFO_UNDERRUN = 0x84,
- TX_3945_STATUS_FAIL_MGMNT_ABORT = 0x85,
- TX_3945_STATUS_FAIL_NEXT_FRAG = 0x86,
- TX_3945_STATUS_FAIL_LIFE_EXPIRE = 0x87,
- TX_3945_STATUS_FAIL_DEST_PS = 0x88,
- TX_3945_STATUS_FAIL_ABORTED = 0x89,
- TX_3945_STATUS_FAIL_BT_RETRY = 0x8a,
- TX_3945_STATUS_FAIL_STA_INVALID = 0x8b,
- TX_3945_STATUS_FAIL_FRAG_DROPPED = 0x8c,
- TX_3945_STATUS_FAIL_TID_DISABLE = 0x8d,
- TX_3945_STATUS_FAIL_FRAME_FLUSHED = 0x8e,
- TX_3945_STATUS_FAIL_INSUFFICIENT_CF_POLL = 0x8f,
- TX_3945_STATUS_FAIL_TX_LOCKED = 0x90,
- TX_3945_STATUS_FAIL_NO_BEACON_ON_RADAR = 0x91,
-};
-
/*
* TX command response is sent after *agn* transmission attempts.
*
@@ -1905,43 +1455,6 @@ struct agg_tx_status {
__le16 sequence;
} __packed;
-struct iwl4965_tx_resp {
- u8 frame_count; /* 1 no aggregation, >1 aggregation */
- u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
- u8 failure_rts; /* # failures due to unsuccessful RTS */
- u8 failure_frame; /* # failures due to no ACK (unused for agg) */
-
- /* For non-agg: Rate at which frame was successful.
- * For agg: Rate at which all frames were transmitted. */
- __le32 rate_n_flags; /* RATE_MCS_* */
-
- /* For non-agg: RTS + CTS + frame tx attempts time + ACK.
- * For agg: RTS + CTS + aggregation tx time + block-ack time. */
- __le16 wireless_media_time; /* uSecs */
-
- __le16 reserved;
- __le32 pa_power1; /* RF power amplifier measurement (not used) */
- __le32 pa_power2;
-
- /*
- * For non-agg: frame status TX_STATUS_*
- * For agg: status of 1st frame, AGG_TX_STATE_*; other frame status
- * fields follow this one, up to frame_count.
- * Bit fields:
- * 11- 0: AGG_TX_STATE_* status code
- * 15-12: Retry count for 1st frame in aggregation (retries
- * occur if tx failed for this frame when it was a
- * member of a previous aggregation block). If rate
- * scaling is used, retry count indicates the rate
- * table entry used for all frames in the new agg.
- * 31-16: Sequence # for this frame's Tx cmd (not SSN!)
- */
- union {
- __le32 status;
- struct agg_tx_status agg_status[0]; /* for each agg frame */
- } u;
-} __packed;
-
/*
* definitions for initial rate index field
* bits [3:0] initial rate index
@@ -2030,51 +1543,7 @@ struct iwl_compressed_ba_resp {
/*
* REPLY_TX_PWR_TABLE_CMD = 0x97 (command, has simple generic response)
*
- * See details under "TXPOWER" in iwl-4965-hw.h.
- */
-
-struct iwl3945_txpowertable_cmd {
- u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
- u8 reserved;
- __le16 channel;
- struct iwl3945_power_per_rate power[IWL_MAX_RATES];
-} __packed;
-
-struct iwl4965_txpowertable_cmd {
- u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
- u8 reserved;
- __le16 channel;
- struct iwl4965_tx_power_db tx_power;
-} __packed;
-
-
-/**
- * struct iwl3945_rate_scaling_cmd - Rate Scaling Command & Response
- *
- * REPLY_RATE_SCALE = 0x47 (command, has simple generic response)
- *
- * NOTE: The table of rates passed to the uCode via the
- * RATE_SCALE command sets up the corresponding order of
- * rates used for all related commands, including rate
- * masks, etc.
- *
- * For example, if you set 9MB (PLCP 0x0f) as the first
- * rate in the rate table, the bit mask for that rate
- * when passed through ofdm_basic_rates on the REPLY_RXON
- * command would be bit 0 (1 << 0)
*/
-struct iwl3945_rate_scaling_info {
- __le16 rate_n_flags;
- u8 try_cnt;
- u8 next_rate_index;
-} __packed;
-
-struct iwl3945_rate_scaling_cmd {
- u8 table_id;
- u8 reserved[3];
- struct iwl3945_rate_scaling_info table[IWL_MAX_RATES];
-} __packed;
-
/*RS_NEW_API: only TLC_RTS remains and moved to bit 0 */
#define LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK (1 << 0)
@@ -2130,7 +1599,7 @@ struct iwl_link_qual_general_params {
#define LINK_QUAL_AGG_DISABLE_START_MAX (255)
#define LINK_QUAL_AGG_DISABLE_START_MIN (0)
-#define LINK_QUAL_AGG_FRAME_LIMIT_DEF (31)
+#define LINK_QUAL_AGG_FRAME_LIMIT_DEF (63)
#define LINK_QUAL_AGG_FRAME_LIMIT_MAX (63)
#define LINK_QUAL_AGG_FRAME_LIMIT_MIN (0)
@@ -2696,14 +2165,6 @@ struct iwl_spectrum_notification {
#define IWL_POWER_BT_SCO_ENA cpu_to_le16(BIT(8))
#define IWL_POWER_ADVANCE_PM_ENA_MSK cpu_to_le16(BIT(9))
-struct iwl3945_powertable_cmd {
- __le16 flags;
- u8 reserved[2];
- __le32 rx_data_timeout;
- __le32 tx_data_timeout;
- __le32 sleep_interval[IWL_POWER_VEC_SIZE];
-} __packed;
-
struct iwl_powertable_cmd {
__le16 flags;
u8 keep_alive_seconds; /* 3945 reserved */
@@ -2806,25 +2267,6 @@ struct iwl_ct_kill_throttling_config {
* active_dwell < max_out_time
*/
-/* FIXME: rename to AP1, remove tpc */
-struct iwl3945_scan_channel {
- /*
- * type is defined as:
- * 0:0 1 = active, 0 = passive
- * 1:4 SSID direct bit map; if a bit is set, then corresponding
- * SSID IE is transmitted in probe request.
- * 5:7 reserved
- */
- u8 type;
- u8 channel; /* band is selected by iwl3945_scan_cmd "flags" field */
- struct iwl3945_tx_power tpc;
- __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
- __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
-} __packed;
-
-/* set number of direct probes u8 type */
-#define IWL39_SCAN_PROBE_MASK(n) ((BIT(n) | (BIT(n) - BIT(1))))
-
struct iwl_scan_channel {
/*
* type is defined as:
@@ -2920,50 +2362,6 @@ struct iwl_ssid_ie {
* struct iwl_scan_channel.
*/
-struct iwl3945_scan_cmd {
- __le16 len;
- u8 reserved0;
- u8 channel_count; /* # channels in channel list */
- __le16 quiet_time; /* dwell only this # millisecs on quiet channel
- * (only for active scan) */
- __le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
- __le16 good_CRC_th; /* passive -> active promotion threshold */
- __le16 reserved1;
- __le32 max_out_time; /* max usec to be away from associated (service)
- * channel */
- __le32 suspend_time; /* pause scan this long (in "extended beacon
- * format") when returning to service channel:
- * 3945; 31:24 # beacons, 19:0 additional usec,
- * 4965; 31:22 # beacons, 21:0 additional usec.
- */
- __le32 flags; /* RXON_FLG_* */
- __le32 filter_flags; /* RXON_FILTER_* */
-
- /* For active scans (set to all-0s for passive scans).
- * Does not include payload. Must specify Tx rate; no rate scaling. */
- struct iwl3945_tx_cmd tx_cmd;
-
- /* For directed active scans (set to all-0s otherwise) */
- struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX_3945];
-
- /*
- * Probe request frame, followed by channel list.
- *
- * Size of probe request frame is specified by byte count in tx_cmd.
- * Channel list follows immediately after probe request frame.
- * Number of channels in list is specified by channel_count.
- * Each channel in list is of type:
- *
- * struct iwl3945_scan_channel channels[0];
- *
- * NOTE: Only one band of channels can be scanned per pass. You
- * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
- * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
- * before requesting another scan.
- */
- u8 data[0];
-} __packed;
-
enum iwl_scan_flags {
/* BIT(0) currently unused */
IWL_SCAN_FLAGS_ACTION_FRAME_TX = BIT(1),
@@ -3090,20 +2488,6 @@ enum iwl_ibss_manager {
* BEACON_NOTIFICATION = 0x90 (notification only, not a command)
*/
-struct iwl3945_beacon_notif {
- struct iwl3945_tx_resp beacon_notify_hdr;
- __le32 low_tsf;
- __le32 high_tsf;
- __le32 ibss_mgr_status;
-} __packed;
-
-struct iwl4965_beacon_notif {
- struct iwl4965_tx_resp beacon_notify_hdr;
- __le32 low_tsf;
- __le32 high_tsf;
- __le32 ibss_mgr_status;
-} __packed;
-
struct iwlagn_beacon_notif {
struct iwlagn_tx_resp beacon_notify_hdr;
__le32 low_tsf;
@@ -3115,14 +2499,6 @@ struct iwlagn_beacon_notif {
* REPLY_TX_BEACON = 0x91 (command, has simple generic response)
*/
-struct iwl3945_tx_beacon_cmd {
- struct iwl3945_tx_cmd tx;
- __le16 tim_idx;
- u8 tim_size;
- u8 reserved1;
- struct ieee80211_hdr frame[0]; /* beacon frame */
-} __packed;
-
struct iwl_tx_beacon_cmd {
struct iwl_tx_cmd tx;
__le16 tim_idx;
@@ -3471,13 +2847,6 @@ struct iwl_statistics_cmd {
#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
#define STATISTICS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
-struct iwl3945_notif_statistics {
- __le32 flag;
- struct iwl39_statistics_rx rx;
- struct iwl39_statistics_tx tx;
- struct iwl39_statistics_general general;
-} __packed;
-
struct iwl_notif_statistics {
__le32 flag;
struct statistics_rx rx;
@@ -4451,10 +3820,6 @@ struct iwl_rx_packet {
__le32 len_n_flags;
struct iwl_cmd_header hdr;
union {
- struct iwl3945_rx_frame rx_frame;
- struct iwl3945_tx_resp tx_resp;
- struct iwl3945_beacon_notif beacon_status;
-
struct iwl_alive_resp alive_frame;
struct iwl_spectrum_notification spectrum_notif;
struct iwl_csa_notification csa_notif;