diff options
Diffstat (limited to 'drivers/net/wireless/rtlwifi/rtl8723as/include/Hal8723PwrSeq.h')
| -rwxr-xr-x | drivers/net/wireless/rtlwifi/rtl8723as/include/Hal8723PwrSeq.h | 171 |
1 files changed, 171 insertions, 0 deletions
diff --git a/drivers/net/wireless/rtlwifi/rtl8723as/include/Hal8723PwrSeq.h b/drivers/net/wireless/rtlwifi/rtl8723as/include/Hal8723PwrSeq.h new file mode 100755 index 000000000000..daa540209429 --- /dev/null +++ b/drivers/net/wireless/rtlwifi/rtl8723as/include/Hal8723PwrSeq.h @@ -0,0 +1,171 @@ +#ifndef __HAL8723PWRSEQ_H__ +#define __HAL8723PWRSEQ_H__ +/* + Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd + There are 6 HW Power States: + 0: POFF--Power Off + 1: PDN--Power Down + 2: CARDEMU--Card Emulation + 3: ACT--Active Mode + 4: LPS--Low Power State + 5: SUS--Suspend + + The transision from different states are defined below + TRANS_CARDEMU_TO_ACT + TRANS_ACT_TO_CARDEMU + TRANS_CARDEMU_TO_SUS + TRANS_SUS_TO_CARDEMU + TRANS_CARDEMU_TO_PDN + TRANS_ACT_TO_LPS + TRANS_LPS_TO_ACT + + TRANS_END +*/ +#include "HalPwrSeqCmd.h" +#include "rtl8723a_spec.h" + +#define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS 15 +#define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS 15 +#define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS 15 +#define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS 15 +#define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS 15 +#define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS 15 +#define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15 +#define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15 +#define RTL8723A_TRANS_END_STEPS 1 + + +#define RTL8723A_TRANS_CARDEMU_TO_ACT \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \ + {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \ + {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \ + {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset 0x04[16]=1*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/ \ + {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 1},/*0x4C[23] = 0x4E[7] = 1, switch DPDT_SEL_P output from WL BB */\ + +#define RTL8723A_TRANS_ACT_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \ + {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \ + {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \ + {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \ + + +#define RTL8723A_TRANS_CARDEMU_TO_SUS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ + +#define RTL8723A_TRANS_SUS_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ + +#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/ \ + {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ + +#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ + {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ + {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/ + + +#define RTL8723A_TRANS_CARDEMU_TO_PDN \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/ + +#define RTL8723A_TRANS_PDN_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/ + +#define RTL8723A_TRANS_ACT_TO_LPS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \ + {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \ + {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \ + {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \ + + +#define RTL8723A_TRANS_LPS_TO_ACT \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ + {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ + {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ + {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\ + {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0 TSF in 40M*/\ + {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ + +#define RTL8723A_TRANS_END \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ + {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, // + + +extern WLAN_PWR_CFG rtl8723A_power_on_flow[RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_radio_off_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_card_disable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_card_enable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_suspend_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_resume_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_hwpdn_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_enter_lps_flow[RTL8723A_TRANS_ACT_TO_LPS_STEPS+RTL8723A_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723A_leave_lps_flow[RTL8723A_TRANS_LPS_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS]; + +#endif + |