diff options
Diffstat (limited to 'drivers/scsi/Kconfig')
-rw-r--r-- | drivers/scsi/Kconfig | 80 |
1 files changed, 49 insertions, 31 deletions
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index eb46cb0e3cb7..6f2c71ef47ee 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -10,6 +10,7 @@ config RAID_ATTRS config SCSI tristate "SCSI device support" depends on BLOCK + select SCSI_DMA if HAS_DMA ---help--- If you want to use a SCSI hard disk, SCSI tape drive, SCSI CD-ROM or any other SCSI device under Linux, say Y and make sure that you know @@ -29,6 +30,10 @@ config SCSI However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device. +config SCSI_DMA + bool + default n + config SCSI_TGT tristate "SCSI target support" depends on SCSI && EXPERIMENTAL @@ -277,7 +282,7 @@ config SCSI_ISCSI_ATTRS config SCSI_SAS_ATTRS tristate "SAS Transport Attributes" - depends on SCSI + depends on SCSI && BLK_DEV_BSG help If you wish to export transport-specific information about each attached SAS device to sysfs, say Y. @@ -286,8 +291,12 @@ source "drivers/scsi/libsas/Kconfig" endmenu -menu "SCSI low-level drivers" +menuconfig SCSI_LOWLEVEL + bool "SCSI low-level drivers" depends on SCSI!=n + default y + +if SCSI_LOWLEVEL config ISCSI_TCP tristate "iSCSI Initiator over TCP/IP" @@ -358,6 +367,7 @@ config SCSI_3W_9XXX config SCSI_7000FASST tristate "7000FASST SCSI support" depends on ISA && SCSI && ISA_DMA_API + select CHECK_SIGNATURE help This driver supports the Western Digital 7000 SCSI host adapter family. Some information is in the source: @@ -379,6 +389,7 @@ config SCSI_AHA152X tristate "Adaptec AHA152X/2825 support" depends on ISA && SCSI && !64BIT select SCSI_SPI_ATTRS + select CHECK_SIGNATURE ---help--- This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825 SCSI host adapters. It also works for the AVA-1505, but the IRQ etc. @@ -478,7 +489,7 @@ source "drivers/scsi/aic94xx/Kconfig" # All the I2O code and drivers do not seem to be 64bit safe. config SCSI_DPT_I2O tristate "Adaptec I2O RAID support " - depends on !64BIT && SCSI && PCI + depends on !64BIT && SCSI && PCI && VIRT_TO_BUS help This driver supports all of Adaptec's I2O based RAID controllers as well as the DPT SmartRaid V cards. This is an Adaptec maintained @@ -540,7 +551,7 @@ config SCSI_HPTIOP config SCSI_BUSLOGIC tristate "BusLogic SCSI support" - depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API + depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API && VIRT_TO_BUS ---help--- This is support for BusLogic MultiMaster and FlashPoint SCSI Host Adapters. Consult the SCSI-HOWTO, available from @@ -574,6 +585,7 @@ config SCSI_DTC3280 tristate "DTC3180/3280 SCSI support" depends on ISA && SCSI select SCSI_SPI_ATTRS + select CHECK_SIGNATURE help This is support for DTC 3180/3280 SCSI Host Adapters. Please read the SCSI-HOWTO, available from @@ -648,6 +660,7 @@ config SCSI_EATA_PIO config SCSI_FUTURE_DOMAIN tristate "Future Domain 16xx SCSI/AHA-2920A support" depends on (ISA || PCI) && SCSI + select CHECK_SIGNATURE ---help--- This is support for Future Domain's 16-bit SCSI host adapters (TMC-1660/1680, TMC-1650/1670, TMC-3260, TMC-1610M/MER/MEX) and @@ -739,7 +752,7 @@ config SCSI_GENERIC_NCR53C400 config SCSI_IBMMCA tristate "IBMMCA SCSI support" - depends on MCA_LEGACY && SCSI + depends on MCA && SCSI ---help--- This is support for the IBM SCSI adapter found in many of the PS/2 series computers. These machines have an MCA bus, so you need to @@ -1007,6 +1020,11 @@ config SCSI_STEX To compile this driver as a module, choose M here: the module will be called stex. +config 53C700_BE_BUS + bool + depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI + default y + config SCSI_SYM53C8XX_2 tristate "SYM53C8XX Version 2 SCSI support" depends on PCI && SCSI @@ -1310,6 +1328,7 @@ config SCSI_LPFC config SCSI_SEAGATE tristate "Seagate ST-02 and Future Domain TMC-8xx SCSI support" depends on X86 && ISA && SCSI + select CHECK_SIGNATURE ---help--- These are 8-bit SCSI controllers; the ST-01 is also supported by this driver. It is explained in section 3.9 of the SCSI-HOWTO, @@ -1383,6 +1402,7 @@ config SCSI_T128 tristate "Trantor T128/T128F/T228 SCSI support" depends on ISA && SCSI select SCSI_SPI_ATTRS + select CHECK_SIGNATURE ---help--- This is support for a SCSI host adapter. It is explained in section 3.11 of the SCSI-HOWTO, available from @@ -1547,7 +1567,7 @@ config A3000_SCSI built-in SCSI controller, say Y. Otherwise, say N. To compile this driver as a module, choose M here: the - module will be called wd33c93. + module will be called a3000. config A2091_SCSI tristate "A2091/A590 WD33C93A support" @@ -1557,7 +1577,7 @@ config A2091_SCSI say N. To compile this driver as a module, choose M here: the - module will be called wd33c93. + module will be called a2091. config GVP11_SCSI tristate "GVP Series II WD33C93A support" @@ -1611,13 +1631,25 @@ config FASTLANE_SCSI If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use one in the near future, say Y to this question. Otherwise, say N. -config SCSI_AMIGA7XX - bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)" - depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN +config SCSI_A4000T + tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)" + depends on AMIGA && SCSI && EXPERIMENTAL + select SCSI_SPI_ATTRS help - Support for various NCR53c710-based SCSI controllers on the Amiga. + If you have an Amiga 4000T and have SCSI devices connected to the + built-in SCSI controller, say Y. Otherwise, say N. + + To compile this driver as a module, choose M here: the + module will be called a4000t. + +config SCSI_ZORRO7XX + tristate "Zorro NCR53c710 SCSI support (EXPERIMENTAL)" + depends on ZORRO && SCSI && EXPERIMENTAL + select SCSI_SPI_ATTRS + help + Support for various NCR53c710-based SCSI controllers on Zorro + expansion boards for the Amiga. This includes: - - the builtin SCSI controller on the Amiga 4000T, - the Amiga 4091 Zorro III SCSI-2 controller, - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller (info at @@ -1625,10 +1657,6 @@ config SCSI_AMIGA7XX - the SCSI controller on the Phase5 Blizzard PowerUP 603e+ accelerator card for the Amiga 1200, - the SCSI controller on the GVP Turbo 040/060 accelerator. - Note that all of the above SCSI controllers, except for the builtin - SCSI controller on the Amiga 4000T, reside on the Zorro expansion - bus, so you also have to enable Zorro bus support if you want to use - them. config OKTAGON_SCSI tristate "BSC Oktagon SCSI support (EXPERIMENTAL)" @@ -1712,8 +1740,8 @@ config MVME147_SCSI single-board computer. config MVME16x_SCSI - bool "NCR53C710 SCSI driver for MVME16x" - depends on MVME16x && SCSI && BROKEN + tristate "NCR53C710 SCSI driver for MVME16x" + depends on MVME16x && SCSI select SCSI_SPI_ATTRS help The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710 @@ -1721,22 +1749,14 @@ config MVME16x_SCSI will want to say Y to this question. config BVME6000_SCSI - bool "NCR53C710 SCSI driver for BVME6000" - depends on BVME6000 && SCSI && BROKEN + tristate "NCR53C710 SCSI driver for BVME6000" + depends on BVME6000 && SCSI select SCSI_SPI_ATTRS help The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710 SCSI controller chip. Almost everyone using one of these boards will want to say Y to this question. -config SCSI_NCR53C7xx_FAST - bool "allow FAST-SCSI [10MHz]" - depends on SCSI_AMIGA7XX || MVME16x_SCSI || BVME6000_SCSI - help - This will enable 10MHz FAST-SCSI transfers with your host - adapter. Some systems have problems with that speed, so it's safest - to say N here. - config SUN3_SCSI tristate "Sun3 NCR5380 SCSI" depends on SUN3 && SCSI @@ -1766,8 +1786,6 @@ config SCSI_SUNESP To compile this driver as a module, choose M here: the module will be called esp. -# bool 'Cyberstorm Mk III SCSI support (EXPERIMENTAL)' CONFIG_CYBERSTORMIII_SCSI - config ZFCP tristate "FCP host bus adapter driver for IBM eServer zSeries" depends on S390 && QDIO && SCSI @@ -1792,7 +1810,7 @@ config SCSI_SRP To compile this driver as a module, choose M here: the module will be called libsrp. -endmenu +endif # SCSI_LOWLEVEL source "drivers/scsi/pcmcia/Kconfig" |