summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/8250
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/8250')
-rw-r--r--drivers/tty/serial/8250/8250_fintek.c19
-rw-r--r--drivers/tty/serial/8250/8250_gsc.c2
-rw-r--r--drivers/tty/serial/8250/8250_mid.c19
-rw-r--r--drivers/tty/serial/8250/8250_of.c11
-rw-r--r--drivers/tty/serial/8250/8250_pci.c147
-rw-r--r--drivers/tty/serial/8250/8250_port.c14
6 files changed, 166 insertions, 46 deletions
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 31c91c2f8c6e..e24161004ddc 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -285,24 +285,6 @@ static void fintek_8250_set_max_fifo(struct fintek_8250 *pdata)
}
}
-static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
- struct fintek_8250 *pdata)
-{
- sio_write_reg(pdata, LDN, pdata->index);
-
- switch (pdata->pid) {
- case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
- sio_write_mask_reg(pdata, F81866_UART_CLK,
- F81866_UART_CLK_MASK,
- F81866_UART_CLK_14_769MHZ);
-
- uart->port.uartclk = 921600 * 16;
- break;
- default: /* leave clock speed untouched */
- break;
- }
-}
-
static void fintek_8250_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
@@ -422,7 +404,6 @@ static int probe_setup_port(struct fintek_8250 *pdata,
fintek_8250_set_irq_mode(pdata, level_mode);
fintek_8250_set_max_fifo(pdata);
- fintek_8250_goto_highspeed(uart, pdata);
fintek_8250_exit_key(addr[i]);
diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c
index 0809ae2aa9b1..51cc985216ff 100644
--- a/drivers/tty/serial/8250/8250_gsc.c
+++ b/drivers/tty/serial/8250/8250_gsc.c
@@ -26,7 +26,7 @@ static int __init serial_init_chip(struct parisc_device *dev)
unsigned long address;
int err;
-#ifdef CONFIG_64BIT
+#if defined(CONFIG_64BIT) && defined(CONFIG_IOSAPIC)
if (!dev->irq && (dev->id.sversion == 0xad))
dev->irq = iosapic_serial_irq(dev);
#endif
diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index efa0515139f8..e6c1791609dd 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -73,6 +73,11 @@ static int pnw_setup(struct mid8250 *mid, struct uart_port *p)
return 0;
}
+static void pnw_exit(struct mid8250 *mid)
+{
+ pci_dev_put(mid->dma_dev);
+}
+
static int tng_handle_irq(struct uart_port *p)
{
struct mid8250 *mid = p->private_data;
@@ -124,6 +129,11 @@ static int tng_setup(struct mid8250 *mid, struct uart_port *p)
return 0;
}
+static void tng_exit(struct mid8250 *mid)
+{
+ pci_dev_put(mid->dma_dev);
+}
+
static int dnv_handle_irq(struct uart_port *p)
{
struct mid8250 *mid = p->private_data;
@@ -330,9 +340,9 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
pci_set_drvdata(pdev, mid);
return 0;
+
err:
- if (mid->board->exit)
- mid->board->exit(mid);
+ mid->board->exit(mid);
return ret;
}
@@ -342,8 +352,7 @@ static void mid8250_remove(struct pci_dev *pdev)
serial8250_unregister_port(mid->line);
- if (mid->board->exit)
- mid->board->exit(mid);
+ mid->board->exit(mid);
}
static const struct mid8250_board pnw_board = {
@@ -351,6 +360,7 @@ static const struct mid8250_board pnw_board = {
.freq = 50000000,
.base_baud = 115200,
.setup = pnw_setup,
+ .exit = pnw_exit,
};
static const struct mid8250_board tng_board = {
@@ -358,6 +368,7 @@ static const struct mid8250_board tng_board = {
.freq = 38400000,
.base_baud = 1843200,
.setup = tng_setup,
+ .exit = tng_exit,
};
static const struct mid8250_board dnv_board = {
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index 9ba31701a372..a9b0a84b1e43 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -105,8 +105,17 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
port->mapsize = resource_size(&resource);
/* Check for shifted address mapping */
- if (of_property_read_u32(np, "reg-offset", &prop) == 0)
+ if (of_property_read_u32(np, "reg-offset", &prop) == 0) {
+ if (prop >= port->mapsize) {
+ dev_warn(&ofdev->dev, "reg-offset %u exceeds region size %pa\n",
+ prop, &port->mapsize);
+ ret = -EINVAL;
+ goto err_unprepare;
+ }
+
port->mapbase += prop;
+ port->mapsize -= prop;
+ }
port->iotype = UPIO_MEM;
if (of_property_read_u32(np, "reg-io-width", &prop) == 0) {
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index a2bb103f22fc..92e2ee278523 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1351,29 +1351,33 @@ pericom_do_set_divisor(struct uart_port *port, unsigned int baud,
{
int scr;
int lcr;
- int actual_baud;
- int tolerance;
- for (scr = 5 ; scr <= 15 ; scr++) {
- actual_baud = 921600 * 16 / scr;
- tolerance = actual_baud / 50;
+ for (scr = 16; scr > 4; scr--) {
+ unsigned int maxrate = port->uartclk / scr;
+ unsigned int divisor = max(maxrate / baud, 1U);
+ int delta = maxrate / divisor - baud;
- if ((baud < actual_baud + tolerance) &&
- (baud > actual_baud - tolerance)) {
+ if (baud > maxrate + baud / 50)
+ continue;
+ if (delta > baud / 50)
+ divisor++;
+
+ if (divisor > 0xffff)
+ continue;
+
+ /* Update delta due to possible divisor change */
+ delta = maxrate / divisor - baud;
+ if (abs(delta) < baud / 50) {
lcr = serial_port_in(port, UART_LCR);
serial_port_out(port, UART_LCR, lcr | 0x80);
-
- serial_port_out(port, UART_DLL, 1);
- serial_port_out(port, UART_DLM, 0);
+ serial_port_out(port, UART_DLL, divisor & 0xff);
+ serial_port_out(port, UART_DLM, divisor >> 8 & 0xff);
serial_port_out(port, 2, 16 - scr);
serial_port_out(port, UART_LCR, lcr);
return;
- } else if (baud > actual_baud) {
- break;
}
}
- serial8250_do_set_divisor(port, baud, quot, quot_frac);
}
static int pci_pericom_setup(struct serial_private *priv,
const struct pciserial_board *board,
@@ -2285,7 +2289,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.setup = pci_pericom_setup_four_at_eight,
},
{
- .vendor = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+ .vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
@@ -2293,6 +2297,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
+ .device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_pericom_setup_four_at_eight,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
@@ -2896,7 +2907,7 @@ enum pci_board_num_t {
pbn_panacom2,
pbn_panacom4,
pbn_plx_romulus,
- pbn_endrun_2_4000000,
+ pbn_endrun_2_3906250,
pbn_oxsemi,
pbn_oxsemi_1_4000000,
pbn_oxsemi_2_4000000,
@@ -3423,10 +3434,10 @@ static struct pciserial_board pci_boards[] = {
* signal now many ports are available
* 2 port 952 Uart support
*/
- [pbn_endrun_2_4000000] = {
+ [pbn_endrun_2_3906250] = {
.flags = FL_BASE0,
.num_ports = 2,
- .base_baud = 4000000,
+ .base_baud = 3906250,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
@@ -4334,7 +4345,7 @@ static const struct pci_device_id serial_pci_tbl[] = {
*/
{ PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_endrun_2_4000000 },
+ pbn_endrun_2_3906250 },
/*
* Quatech cards. These actually have configurable clocks but for
* now we just use the default.
@@ -5119,8 +5130,30 @@ static const struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_INTASHIELD, PCI_DEVICE_ID_INTASHIELD_IS400,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, /* 135a.0dc0 */
pbn_b2_4_115200 },
+ /* Brainboxes Devices */
+ /*
+ * Brainboxes UC-101
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0BA1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
/*
- * BrainBoxes UC-260
+ * Brainboxes UC-235/246
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0AA1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_1_115200 },
+ /*
+ * Brainboxes UC-257
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0861,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-260/271/701/756
*/
{ PCI_VENDOR_ID_INTASHIELD, 0x0D21,
PCI_ANY_ID, PCI_ANY_ID,
@@ -5128,7 +5161,81 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_b2_4_115200 },
{ PCI_VENDOR_ID_INTASHIELD, 0x0E34,
PCI_ANY_ID, PCI_ANY_ID,
- PCI_CLASS_COMMUNICATION_MULTISERIAL << 8, 0xffff00,
+ PCI_CLASS_COMMUNICATION_MULTISERIAL << 8, 0xffff00,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-268
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0841,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-275/279
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0881,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_8_115200 },
+ /*
+ * Brainboxes UC-302
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x08E1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-310
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x08C1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-313
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x08A3,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-320/324
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0A61,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_1_115200 },
+ /*
+ * Brainboxes UC-346
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0B02,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-357
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0A81,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ { PCI_VENDOR_ID_INTASHIELD, 0x0A83,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-368
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0C41,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-420/431
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0921,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
pbn_b2_4_115200 },
/*
* Perle PCI-RAS cards
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 777ef1a9591c..c1891c55897a 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1545,6 +1545,18 @@ static inline void start_tx_rs485(struct uart_port *port)
if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX))
serial8250_stop_rx(&up->port);
+ /*
+ * While serial8250_em485_handle_stop_tx() is a noop if
+ * em485->active_timer != &em485->stop_tx_timer, it might happen that
+ * the timer is still armed and triggers only after the current bunch of
+ * chars is send and em485->active_timer == &em485->stop_tx_timer again.
+ * So cancel the timer. There is still a theoretical race condition if
+ * the timer is already running and only comes around to check for
+ * em485->active_timer when &em485->stop_tx_timer is armed again.
+ */
+ if (em485->active_timer == &em485->stop_tx_timer)
+ hrtimer_try_to_cancel(&em485->stop_tx_timer);
+
em485->active_timer = NULL;
mcr = serial8250_in_MCR(up);
@@ -3172,7 +3184,7 @@ static void serial8250_console_restore(struct uart_8250_port *up)
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
- serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
+ serial8250_out_MCR(up, up->mcr | UART_MCR_DTR | UART_MCR_RTS);
}
/*
generated by cgit v1.2.3 (git 2.0.4) at 2024-04-28 18:15:58 +0000