Age | Commit message (Collapse) | Author |
|
|
|
This is the 5.4.193 stable release
Conflicts:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
drivers/edac/synopsys_edac.c
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/mmc/host/sdhci.c
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
sound/soc/codecs/msm8916-wcd-analog.c
|
|
commit 7102ffe4c166ca0f5e35137e9f9de83768c2d27d upstream.
According to document and code, ext4_xattr_header's size is 32 bytes, so
h_reserved size should be 3.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com>
Link: https://lore.kernel.org/r/92fcc3a6-7d77-8c09-4126-377fcb4c46a5@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90c204d3195a795f77f5bce767e311dd1c59ca17 upstream.
The interrupt property is not mandatory at all, this property should not
be part of the required properties list, so move it into the optional
properties list.
Fixes: 326e5c8d4a87 ("dt-binding: spi: Document Macronix controller bindings")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0e7f1b557974ce297e5e4c9d4245720fbb489886 upstream.
The controller properties should be in the controller 'parent' node,
while properties in the children nodes are specific to the NAND
*chip*. This error was already present during the yaml conversion.
Fixes: 2d472aba15ff ("mtd: nand: document the NAND controller/NAND chip DT representation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93f2ec9e401276fb4ea9903194a5bfcf175f9a2c upstream.
The reg property of a NAND device always references the chip-selects.
The ready/busy lines are described in the nand-rb property. I believe
this was a harmless copy/paste error during the conversion to yaml.
Fixes: 212e49693592 ("dt-bindings: mtd: Add YAML schemas for the generic NAND options")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ef248d9bd616b04df8be25539a4dc5db4b6c56f4 ]
This fixes the near-silence of the headphone jack on the ALC256-based
Samsung Galaxy Book Flex Alpha (NP730QCJ). The magic verbs were found
through trial and error, using known ALC298 hacks as inspiration. The
fixup is auto-enabled only when the NP730QCJ is detected. It can be
manually enabled using model=alc256-samsung-headphone.
Signed-off-by: Matt Kramer <mccleetus@gmail.com>
Link: https://lore.kernel.org/r/3168355.aeNJFYEL58@linus
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 555d44932c67e617d89bc13c81c7efac5b51fcfa upstream.
The link to stable tree is redirected to
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git. Update
accordingly.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20220314113329.485372-6-bagasdotme@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 587d39b260c4d090166314d64be70b1f6a26b0b5 upstream.
There is also stable release candidate tree. Mention it, however with a
warning that the tree is for testing purposes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20220314113329.485372-5-bagasdotme@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ddbd89deb7d32b1fbb879f48d68fda1a8ac58e8e upstream.
The problem I'm addressing was discovered by the LTP test covering
cve-2018-1000204.
A short description of what happens follows:
1) The test case issues a command code 00 (TEST UNIT READY) via the SG_IO
interface with: dxfer_len == 524288, dxdfer_dir == SG_DXFER_FROM_DEV
and a corresponding dxferp. The peculiar thing about this is that TUR
is not reading from the device.
2) In sg_start_req() the invocation of blk_rq_map_user() effectively
bounces the user-space buffer. As if the device was to transfer into
it. Since commit a45b599ad808 ("scsi: sg: allocate with __GFP_ZERO in
sg_build_indirect()") we make sure this first bounce buffer is
allocated with GFP_ZERO.
3) For the rest of the story we keep ignoring that we have a TUR, so the
device won't touch the buffer we prepare as if the we had a
DMA_FROM_DEVICE type of situation. My setup uses a virtio-scsi device
and the buffer allocated by SG is mapped by the function
virtqueue_add_split() which uses DMA_FROM_DEVICE for the "in" sgs (here
scatter-gather and not scsi generics). This mapping involves bouncing
via the swiotlb (we need swiotlb to do virtio in protected guest like
s390 Secure Execution, or AMD SEV).
4) When the SCSI TUR is done, we first copy back the content of the second
(that is swiotlb) bounce buffer (which most likely contains some
previous IO data), to the first bounce buffer, which contains all
zeros. Then we copy back the content of the first bounce buffer to
the user-space buffer.
5) The test case detects that the buffer, which it zero-initialized,
ain't all zeros and fails.
One can argue that this is an swiotlb problem, because without swiotlb
we leak all zeros, and the swiotlb should be transparent in a sense that
it does not affect the outcome (if all other participants are well
behaved).
Copying the content of the original buffer into the swiotlb buffer is
the only way I can think of to make swiotlb transparent in such
scenarios. So let's do just that if in doubt, but allow the driver
to tell us that the whole mapped buffer is going to be overwritten,
in which case we can preserve the old behavior and avoid the performance
impact of the extra bounce.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9b6013a7ce31535b04b02ba99babefe8a8599fa upstream.
Update the link to the "Software Techniques for Managing Speculation
on AMD Processors" whitepaper.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ad3eb1132453b9795ce5fd4572b1c18b292cca9 upstream.
Update the doc with the new fun.
[ bp: Massage commit message. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[fllinden@amazon.com: backported to 5.4]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TI TMP1075 is a LM75 compatible sensor, so lets
add support for it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210429121150.106804-1-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
(cherry picked from commit ec081f9154766be98b7be6e4c4483b580c5b12e7)
|
|
commit 08389d888287c3823f80b0216766b71e17f0aba5 upstream.
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
[fllinden@amazon.com: backported to 5.4]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a06247c6804f1a7c86a2e5398a4c1f1db1471848 upstream.
With write operation on psi files replacing old trigger with a new one,
the lifetime of its waitqueue is totally arbitrary. Overwriting an
existing trigger causes its waitqueue to be freed and pending poll()
will stumble on trigger->event_wait which was destroyed.
Fix this by disallowing to redefine an existing psi trigger. If a write
operation is used on a file descriptor with an already existing psi
trigger, the operation will fail with EBUSY error.
Also bypass a check for psi_disabled in the psi_trigger_destroy as the
flag can be flipped after the trigger is created, leading to a memory
leak.
Fixes: 0e94682b73bf ("psi: introduce psi monitor")
Reported-by: syzbot+cdb5dd11c97cc532efad@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Analyzed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220111232309.1786347-1-surenb@google.com
[surenb: backported to 5.4 kernel]
CC: stable@vger.kernel.org # 5.4
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17a30422621c0e04cb6060d20d7edcefd7463347 upstream.
This tcan4x5x only comes with 2K of MRAM, a RX FIFO with a dept of 32
doesn't fit into the MRAM. Use a depth of 16 instead.
Fixes: 4edd396a1911 ("dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver")
Link: https://lore.kernel.org/all/20220119062951.2939851-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 640f35b871d29cd685ce0ea0762636381beeb98a upstream.
This property was already mentioned in the old textual bindings
amlogic,meson-vpu.txt, but got dropped during conversion.
Adding it back similar to amlogic,gx-vdec.yaml.
Fixes: 6b9ebf1e0e67 ("dt-bindings: display: amlogic, meson-vpu: convert to yaml")
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219094155.177206-1-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22bf4047d26980807611b7e2030803db375afd87 upstream.
This is used in meson-gx and meson-g12. Add the property to the binding.
This fixes the dtschema warning:
hdmi-tx@c883a000: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Fixes: 376bf52deef5 ("dt-bindings: display: amlogic, meson-dw-hdmi: convert to yaml")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211223122434.39378-2-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0ac702f3329cdc8a06dcaac73183d4b5a2b942d upstream.
Adjust the path of the ABI files for firewire.rst to prevent a
documentation build error. Prevents this problem:
Sphinx parallel build error:
docutils.utils.SystemMessage: Documentation/driver-api/firewire.rst:22: (SEVERE/4) Problems with "include" directive path:
InputError: [Errno 2] No such file or directory: '../Documentation/driver-api/ABI/stable/firewire-cdev'.
Fixes: 2f4830ef96d2 ("FireWire: add driver-api Introduction section")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/r/20220119033905.4779-1-rdunlap@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
randomization
commit 82ca67321f55a8d1da6ac3ed611da3c32818bb37 upstream.
The config RANDOMIZE_SLAB does not exist, the authors probably intended to
refer to the config RANDOMIZE_BASE, which provides kernel address-space
randomization. They probably just confused SLAB with BASE (these two
four-letter words coincidentally share three common letters), as they also
point out the config SLAB_FREELIST_RANDOM as further randomization within
the same sentence.
Fix the reference of the config for kernel address-space randomization to
the config that provides that.
Fixes: 6e88559470f5 ("Documentation: Add section about CPU vulnerabilities for Spectre")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211230171940.27558-1-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a11174952205d082f1658fab4314f0caf706e0a8 upstream.
The data node reference documentation was missing a package that must
contain the property values, instead property name and multiple values
being present in a single package. This is not aligned with the _DSD
spec.
Fix it by adding the package for the values.
Also add the missing "reg" properties to two numbered nodes.
Fixes: b10134a3643d ("ACPI: property: Document hierarchical data extension references")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c61d7b2ef141abf81140756b45860a2306f395a2 upstream.
Currently the documentation states that channels must be configured before
running the dmatest. This has not been true since commit 6b41030fdc79
("dmaengine: dmatest: Restore default for channel"). Fix accordingly.
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20211118100952.27268-3-daniel.thompson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
toradex_5.4-2.3.x-imx-v5.4.161
Conflicts:
drivers/net/phy/micrel.c
drivers/usb/chipidea/core.c
|
|
This is the 5.4.160 stable release
|
|
[ Upstream commit 9222ba68c3f4065f6364b99cc641b6b019ef2d42 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0ff29701ffad9a5d5a24344d8b09f3af7b96ffda upstream.
Update the documentation for kvm-intel's emulate_invalid_guest_state to
rectify the description of KVM's default behavior, and to document that
the behavior and thus parameter only applies to L1.
Fixes: a27685c33acc ("KVM: VMX: Emulate invalid guest state by default")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211207193006.120997-4-seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 229d495d8189ae785dacee72e5633a58edc25ddf ]
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c15b05baea71a5ff98235783e3e4ad227760876 ]
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 96db48c9d777a73a33b1d516c5cfed7a417a5f40 upstream.
This binding was already documented in phy.txt, commit 252ae5330daa
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c109
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c109 ("dt-bindings: net: Add a YAML schemas for the generic PHY options")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c95c07836fa4c1767ed11d8eca0769c652760e32 ]
We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900aa ("ipvs:
Fix reuse connection if real server is dead").
For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().
Fixes: d752c3645717 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit baf8d6899b1e8906dc076ef26cc633e96a8bb0c3 upstream.
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d6953009 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40fdea0284bb20814399da0484a658a96c735d90 upstream.
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
s5m8767,pmic-buck-default-dvs-idx property
commit a7fda04bc9b6ad9da8e19c9e6e3b1dab773d068a upstream.
The driver was always parsing "s5m8767,pmic-buck-default-dvs-idx", not
"s5m8767,pmic-buck234-default-dvs-idx".
Cc: <stable@vger.kernel.org>
Fixes: 26aec009f6b6 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-3-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
disabled
commit b16bef60a9112b1e6daf3afd16484eb06e7ce792 upstream.
The driver and its bindings, before commit 04f9f068a619 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a619 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
This is the 5.4.148 stable release
Conflicts:
- drivers/dma/imx-sdma.c:
Following upstream patches are already applied to NXP tree:
7cfbf391e870 ("dmaengine: imx-sdma: remove duplicated sdma_load_context")
788122c99d85 ("Revert "dmaengine: imx-sdma: refine to load context only
once"")
- drivers/usb/chipidea/host.c:
Merge upstream commit a18cfd715e91 ("usb: chipidea: host: fix port index
underflow and UBSAN complains") to NXP version.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
[ Upstream commit 778cb8e39f6ec252be50fc3850d66f3dcbd5dd5a ]
"PAGESIZE / 512" is the number of ECC chunks.
"ECC_BYTES" is the number of bytes needed to store a single ECC code.
"2" is the space reserved by the bad block marker.
"2 + (PAGESIZE / 512) * ECC_BYTES" should of course be lower or equal
than the total number of OOB bytes, otherwise it won't fit.
Fix the equation by substituting s/>=/<=/.
Suggested-by: Ryan J. Barnett <ryan.barnett@collins.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20210610143945.3504781-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 55c21d57eafb7b379bb7b3e93baf9ca2695895b0 upstream.
Fix board compatible typo reported by dtbs_check.
Fixes: f4d1577e9bc6 ("dt-bindings: arm: Convert Tegra board/soc bindings to json-schema")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210912165120.188490-1-david@ixit.cz
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8d7e415d55610d503fdb8815344846b72d194a40 ]
Starting from the beginning of infiniband subsystem, the uverbs char
devices start from 192 as a minor number, see
commit bc38a6abdd5a ("[PATCH] IB uverbs: core implementation").
This patch updates the admin guide documentation to reflect it.
Fixes: 9d85025b0418 ("docs-rst: create an user's manual book")
Link: https://lore.kernel.org/r/bad03e6bcde45550c01e12908a6fe7dfa4770703.1627477347.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.4.141 stable release
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
commit b1bd5cba3306691c771d558e94baa73e8b0b96b7 upstream.
When computing the access permissions of a shadow page, use the effective
permissions of the walk up to that point, i.e. the logic AND of its parents'
permissions. Two guest PxE entries that point at the same table gfn need to
be shadowed with different shadow pages if their parents' permissions are
different. KVM currently uses the effective permissions of the last
non-leaf entry for all non-leaf entries. Because all non-leaf SPTEs have
full ("uwx") permissions, and the effective permissions are recorded only
in role.access and merged into the leaves, this can lead to incorrect
reuse of a shadow page and eventually to a missing guest protection page
fault.
For example, here is a shared pagetable:
pgd[] pud[] pmd[] virtual address pointers
/->pmd1(u--)->pte1(uw-)->page1 <- ptr1 (u--)
/->pud1(uw-)--->pmd2(uw-)->pte2(uw-)->page2 <- ptr2 (uw-)
pgd-| (shared pmd[] as above)
\->pud2(u--)--->pmd1(u--)->pte1(uw-)->page1 <- ptr3 (u--)
\->pmd2(uw-)->pte2(uw-)->page2 <- ptr4 (u--)
pud1 and pud2 point to the same pmd table, so:
- ptr1 and ptr3 points to the same page.
- ptr2 and ptr4 points to the same page.
(pud1 and pud2 here are pud entries, while pmd1 and pmd2 here are pmd entries)
- First, the guest reads from ptr1 first and KVM prepares a shadow
page table with role.access=u--, from ptr1's pud1 and ptr1's pmd1.
"u--" comes from the effective permissions of pgd, pud1 and
pmd1, which are stored in pt->access. "u--" is used also to get
the pagetable for pud1, instead of "uw-".
- Then the guest writes to ptr2 and KVM reuses pud1 which is present.
The hypervisor set up a shadow page for ptr2 with pt->access is "uw-"
even though the pud1 pmd (because of the incorrect argument to
kvm_mmu_get_page in the previous step) has role.access="u--".
- Then the guest reads from ptr3. The hypervisor reuses pud1's
shadow pmd for pud2, because both use "u--" for their permissions.
Thus, the shadow pmd already includes entries for both pmd1 and pmd2.
- At last, the guest writes to ptr4. This causes no vmexit or pagefault,
because pud1's shadow page structures included an "uw-" page even though
its role.access was "u--".
Any kind of shared pagetable might have the similar problem when in
virtual machine without TDP enabled if the permissions are different
from different ancestors.
In order to fix the problem, we change pt->access to be an array, and
any access in it will not include permissions ANDed from child ptes.
The test code is: https://lore.kernel.org/kvm/20210603050537.19605-1-jiangshanlai@gmail.com/
Remember to test it with TDP disabled.
The problem had existed long before the commit 41074d07c78b ("KVM: MMU:
Fix inherited permissions for emulated guest pte updates"), and it
is hard to find which is the culprit. So there is no fixes tag here.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20210603052455.21023-1-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
Fixes: cea0f0e7ea54 ("[PATCH] KVM: MMU: Shadow page table caching")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[OP: - apply arch/x86/kvm/mmu/* changes to arch/x86/kvm
- apply documentation changes to Documentation/virt/kvm/mmu.txt
- adjusted context in arch/x86/kvm/paging_tmpl.h]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.4.136 stable release
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
commit e71e2ace5721a8b921dca18b045069e7bb411277 upstream.
Patch series "userfaultfd: do not untag user pointers", v5.
If a user program uses userfaultfd on ranges of heap memory, it may end
up passing a tagged pointer to the kernel in the range.start field of
the UFFDIO_REGISTER ioctl. This can happen when using an MTE-capable
allocator, or on Android if using the Tagged Pointers feature for MTE
readiness [1].
When a fault subsequently occurs, the tag is stripped from the fault
address returned to the application in the fault.address field of struct
uffd_msg. However, from the application's perspective, the tagged
address *is* the memory address, so if the application is unaware of
memory tags, it may get confused by receiving an address that is, from
its point of view, outside of the bounds of the allocation. We observed
this behavior in the kselftest for userfaultfd [2] but other
applications could have the same problem.
Address this by not untagging pointers passed to the userfaultfd ioctls.
Instead, let the system call fail. Also change the kselftest to use
mmap so that it doesn't encounter this problem.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
This patch (of 2):
Do not untag pointers passed to the userfaultfd ioctls. Instead, let
the system call fail. This will provide an early indication of problems
with tag-unaware userspace code instead of letting the code get confused
later, and is consistent with how we decided to handle brk/mmap/mremap
in commit dcde237319e6 ("mm: Avoid creating virtual address aliases in
brk()/mmap()/mremap()"), as well as being consistent with the existing
tagged address ABI documentation relating to how ioctl arguments are
handled.
The code change is a revert of commit 7d0325749a6c ("userfaultfd: untag
user pointers") plus some fixups to some additional calls to
validate_range that have appeared since then.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
Link: https://lkml.kernel.org/r/20210714195437.118982-1-pcc@google.com
Link: https://lkml.kernel.org/r/20210714195437.118982-2-pcc@google.com
Link: https://linux-review.googlesource.com/id/I761aa9f0344454c482b83fcfcce547db0a25501b
Fixes: 63f0c6037965 ("arm64: Introduce prctl() options to control the tagged user addresses ABI")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mitch Phillips <mitchp@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: William McVicker <willmcvicker@google.com>
Cc: <stable@vger.kernel.org> [5.4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e3bac71c5053c99d438771fc9fa5082ae5d90aa upstream.
Currently the histogram logic allows the user to write "cpu" in as an
event field, and it will record the CPU that the event happened on.
The problem with this is that there's a lot of events that have "cpu"
as a real field, and using "cpu" as the CPU it ran on, makes it
impossible to run histograms on the "cpu" field of events.
For example, if I want to have a histogram on the count of the
workqueue_queue_work event on its cpu field, running:
># echo 'hist:keys=cpu' > events/workqueue/workqueue_queue_work/trigger
Gives a misleading and wrong result.
Change the command to "common_cpu" as no event should have "common_*"
fields as that's a reserved name for fields used by all events. And
this makes sense here as common_cpu would be a field used by all events.
Now we can even do:
># echo 'hist:keys=common_cpu,cpu if cpu < 100' > events/workqueue/workqueue_queue_work/trigger
># cat events/workqueue/workqueue_queue_work/hist
# event histogram
#
# trigger info: hist:keys=common_cpu,cpu:vals=hitcount:sort=hitcount:size=2048 if cpu < 100 [active]
#
{ common_cpu: 0, cpu: 2 } hitcount: 1
{ common_cpu: 0, cpu: 4 } hitcount: 1
{ common_cpu: 7, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 1 } hitcount: 1
{ common_cpu: 0, cpu: 6 } hitcount: 2
{ common_cpu: 0, cpu: 5 } hitcount: 2
{ common_cpu: 1, cpu: 1 } hitcount: 4
{ common_cpu: 6, cpu: 6 } hitcount: 4
{ common_cpu: 5, cpu: 5 } hitcount: 14
{ common_cpu: 4, cpu: 4 } hitcount: 26
{ common_cpu: 0, cpu: 0 } hitcount: 39
{ common_cpu: 2, cpu: 2 } hitcount: 184
Now for backward compatibility, I added a trick. If "cpu" is used, and
the field is not found, it will fall back to "common_cpu" and work as
it did before. This way, it will still work for old programs that use
"cpu" to get the actual CPU, but if the event has a "cpu" as a field, it
will get that event's "cpu" field, which is probably what it wants
anyway.
I updated the tracefs/README to include documentation about both the
common_timestamp and the common_cpu. This way, if that text is present in
the README, then an application can know that common_cpu is supported over
just plain "cpu".
Link: https://lkml.kernel.org/r/20210721110053.26b4f641@oasis.local.home
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 8b7622bf94a44 ("tracing: Add cpu field for hist triggers")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.4.132 stable release
Conflicts (manual resolve):
- drivers/gpu/drm/rockchip/cdn-dp-core.c:
Fix merge hiccup when integrating upstream commit 450c25b8a4c9c
("drm/rockchip: cdn-dp-core: add missing clk_disable_unprepare() on
error in cdn_dp_grf_write()")
- drivers/perf/fsl_imx8_ddr_perf.c:
Port upstream commit 3fea9b708ae37 ("drivers/perf: fix the missed
ida_simple_remove() in ddr_perf_probe()") manually to NXP version.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
commit 8669dbab2ae56085c128894b181c2aa50f97e368 upstream.
Patch series "Actually fix freelist pointer vs redzoning", v4.
This fixes redzoning vs the freelist pointer (both for middle-position
and very small caches). Both are "theoretical" fixes, in that I see no
evidence of such small-sized caches actually be used in the kernel, but
that's no reason to let the bugs continue to exist, especially since
people doing local development keep tripping over it. :)
This patch (of 3):
Instead of repeating "Redzone" and "Poison", clarify which sides of
those zones got tripped. Additionally fix column alignment in the
trailer.
Before:
BUG test (Tainted: G B ): Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
After:
BUG test (Tainted: G B ): Right Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
The earlier commits that slowly resulted in the "Before" reporting were:
d86bd1bece6f ("mm/slub: support left redzone")
ffc79d288000 ("slub: use print_hex_dump")
2492268472e7 ("SLUB: change error reporting format to follow lockdep loosely")
Link: https://lkml.kernel.org/r/20210608183955.280836-1-keescook@chromium.org
Link: https://lkml.kernel.org/r/20210608183955.280836-2-keescook@chromium.org
Link: https://lore.kernel.org/lkml/cfdb11d7-fb8e-e578-c939-f7f5fb69a6bd@suse.cz/
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Marco Elver <elver@google.com>
Cc: "Lin, Zhenpeng" <zplin@psu.edu>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8fc75643c5e14574c8be59b69182452ece28315a upstream
In order to use multi-index entries for huge pages in the page cache, we
need to be able to split a multi-index entry (eg if a file is truncated in
the middle of a huge page entry). This version does not support splitting
more than one level of the tree at a time. This is an acceptable
limitation for the page cache as we do not expect to support order-12
pages in the near future.
[akpm@linux-foundation.org: export xas_split_alloc() to modules]
[willy@infradead.org: fix xarray split]
Link: https://lkml.kernel.org/r/20200910175450.GV6583@casper.infradead.org
[willy@infradead.org: fix xarray]
Link: https://lkml.kernel.org/r/20201001233943.GW20115@casper.infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Qian Cai <cai@lca.pw>
Cc: Song Liu <songliubraving@fb.com>
Link: https://lkml.kernel.org/r/20200903183029.14930-3-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aac902925ea646e461c95edc98a8a57eb0def917 upstream.
The documentation had some previously incorrect information about how
userspace notifications (and responses) were handled due to a change
from a previously proposed patchset.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Tycho Andersen <tycho@tycho.pizza>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210517193908.3113-2-sargun@sargun.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c25ce589dca10d64dde139ae093abc258a32869c upstream.
Change every shebang which does not need an argument to use /usr/bin/env.
This is needed as not every distro has everything under /usr/bin,
sometimes not even bash.
Signed-off-by: Finn Behrens <me@kloenk.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|