| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit ca244a83ecc7f0a9242ee2116e622cb6d7ec2a90 ]
On chiliSOM TPS65217 nWAKEUP pin is connected to AM335x internal RTC
EXT_WAKEUP input. In RTC-only state TPS65217 is notifying about power on
events (such as power buton presses) by setting nWAKEUP output
low. After that it waits 5s for proper device boot. Currently it doesn't
happen, as the processor doesn't listen for such events. Consequently
TPS65217 changes state from SLEEP (RTC-only state) to OFF.
Enable EXT_WAKEUP input of AM335x's RTC, so the processor can properly
detect power on events and recover immediately from RTC-only states,
without powering off RTC and losing time.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ChiliSOM has TPS65217's PWR_EN pin connected to AM335x PMIC_POWER_EN
pin. Processor's PMIC_POWER_EN is controlled by it's internal RTC, hence
RTC subsystem is responsible for proper board poweroff sequence.
This change enables complete poweroff sequence for ChiliBoard, switching
PMIC's state from ACTIVE to SLEEP.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ChiliSOM has 2 Ethernet subsystems with different types of possibly used
PHY interfaces (i.e. MII, RMII, GMII, RGMII). Current code configured
pinmux for RMII on 1st Ethernet subsystem and enabled Ethernet MAC with
1 slave for all boards which use ChiliSOM.
This change moves pinmux configuration of 1st Ethernet subsystem to
ChiliBoard description, as this is board-specific.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
uart0 configuration code has been in SOM. However, it is possible to
use all (or none) of 6 uart's of AM335x processor present on ChiliSOM.
This fix moves declaration of uart0 from ChiliSOM to ChiliBoard, because
use of uart is strictly board-specific.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.
Read speed increases from 7869 KiB/ to 8875 KiB/s
and write speed was unchanged at 5100 KiB/s.
Measured using mtd_speedtest.ko on am335x-evm.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
plus a couple of related 64-bit updates:
New SoC support:
- Allwinner A83T
- Axis Artpec-6 SoC
- Mediatek MT7623 SoC
- TI Keystone K2G SoC
- ST Microelectronics stm32f469
New board or machine support:
- ARM Juno R2
- Buffalo Linkstation LS-QVL and LS-GL
- Cubietruck plus
- D-Link DIR-885L
- DT support for ARM RealView PB1176 and PB11MPCore
- Google Nexus 7
- Homlet v2
- Itead Ibox
- Lamobo R1
- LG Optimus Black
- Logicpd dm3730
- Raspberry Pi Model A
Other changes include
- Lots of updates for Qualcomm APQ8064, MSM8974 and others
- Improved support for Nokia N900 and other OMAP machines
- Common clk support for lpc32xx
- HDLCD display on ARM
- Improved stm32f429 support
- Improved Renesas device support, r8a779x and others
- Lots of Rockchip updates
- Samsung cleanups
- ADC support for Atmel SAMA5D2
- BCM2835 (Raspberry Pi) improvements
- Broadcom Northstar Plus enhancements
- OMAP GPMC rework
- Several improvements for Atmel SAMA5D2 / Xplained
- Global change to remove inofficial "arm,amba-bus" compatible
string"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (350 commits)
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus"
ARM: dts: artpec: dual-license on artpec6.dtsi
ARM: dts: ux500: add synaptics RMI4 for Ux500 TVK DT
arm64: dts: juno/vexpress: fix node name unit-address presence warnings
arm64: dts: foundation-v8: add SBSA Generic Watchdog device node
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: stm32f429: Enable Ethernet on Eval board
ARM: dts: omap3-sniper: TWL4030 keypad support
Revert "ARM: dts: DRA7: Add dt nodes for PWMSS"
ARM: dts: dm814x: dra62x: Disable wait pin monitoring for NAND
ARM: dts: dm814x: dra62x: Fix NAND device nodes
ARM: dts: stm32f429: Add Ethernet support
ARM: dts: stm32f429: Add system config bank node
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
ARM: dts: exynos: Don't overheat the Odroid XU3-Lite on high load
ARM: dts: exynos: Add cooling levels for Exynos5422/5800 CPUs
...
|
|
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM335x TRM: SPRUH73L: 7.1.3.3.12.2 NAND Device-Ready Pin
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This reverts commit 8e6ebfaa9b384088002baa10f7534efa73a0794e.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
remove tps65217.dtsi and adapt all boards, which
used it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since this is a SOM (System on Module) that will be part
of another embedded board (and can't really exist on its own)
define it as a "dtsi" that will be included in the Device tree
describing the whole system later on.
Hardware specification:
* AM335x SoC
* up to 512 MB RAM
* NAND Flash (8x interface, cs0)
* UART0
* PMIC
* I2C0 (for PMIC)
* 1x Ethernet MAC
Signed-off-by: Rostislav Lisovy <lisovy@jablotron.cz>
[tony@atomide.com: updated nand io size to be just 4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
