| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 0a5aff64f20d92c5a6e9aeed7b5950b0b817bcd9 ]
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 77416ab35f5712382e5a792bfa1736ceb70d5bbb ]
The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.
Fixes: 70725d6e97ac ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c3762437 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This uses the existing Northstar USB3 PHY driver to enable the USB3
ports on NSP.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
|
|
Add the EHCI and OHCI entries to the Northstar Plus device tree files.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add and enable the third AMAC ethernet interface in the device trees for
the platforms where it is present. Also, enable amac1 on some of the
platforms where that was missing.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
QSPI device tree entries are present in bcm958625k, but missing from
bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
bcm958625hr, and bcm988312hr. Duplicate the entry in bcm958625k for
all of those that are missing it (as they are identical).
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The QSPI entry was added out of the sequental order that the rest of the
DTSI file is in. Move it to make it fit in properly. Also, some other
entries have been added in a non-alphabetical order in the DTS files,
making them different from the other NSP DTS files. Move the relevant
peices to make it match. Finally, remove errant new lines.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add the ability to reboot the bcm958625hr board via GPIO.
Unfortunately, not all of the NSP based boards use the same GPIO pin and
one doesn't have the ability to reboot via GPIO at all. So, this will
need to be specified per DTS file.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add SATA support to bcm958625hr DTS
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The BCM958625HR board has 2GB of RAM available. Increase the amount
from 512MB to 2GB and add the device type to the memory entry.
Fixes: 9a4865d42fe5 ("ARM: dts: NSP: Specify RAM amount for BCM958625HR board")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add the layout of the switch ports found on the BCM958625HR reference
board. The CPU port is hooked up to the AMAC0 Ethernet controlelr
adapter, so we also enable it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add 512MB of memory starting at physical offset 0x6000_0000.
Fixes: 65e9ac208c8e ("ARM: dts: NSP: Add new DT file for bcm958625hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Create a new device tree file for the Broadcom Northstar Plus HR SVK.
This SVK is a smaller form factor, and thus only has 2 PCI slots and 1
UART. Also, it has the ability to reboot via GPIO (instead of the
processor reset).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
