| Age | Commit message (Collapse) | Author |
|---|
|
The Capacitive Touch Adapter is an interface board designed to easily
connect the Capacitive Touch Display 7" Parallel to the Colibri Carrier
boards which do not have PCAP connector yet available on board.
Change the pins for interrupt and reset to those defined in the
Capacitive Touch Adapter's datasheet.
While at it remove the '#ifdef PCAP' in favour of disabled nodes.
That way one can fixup the device tree in U-Boot to disable the
pwm nodes and enable the connected touch controller.
e.g. for a Colibri iMX6S/DL:
Colibri iMX6 # setenv fdt_fixup 'fdt addr ${fdt_addr_r} && fdt resize && fdt set /soc/aips-bus@02100000/i2c@021a8000/atmel_mxt_ts@4a status okay; fdt set /soc/aips-bus@02000000/pwm@02080000 status disabled; fdt set /soc/aips-bus@02000000/pwm@0208c000 status disabled'
Colibri iMX6 # saveenv
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Toradex Carrier boards use the ST M41T0 RTC (not M41T00). The RTC
is almost the same, but the M41T0 needs some special handling in
case the oscillator fails. Now that support for this difference is
available, using the new compatible string to make use of it.
Sync with commit 10e718b1c60c4e490e6972cfa58e97fcf5260685
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Synced with 558d378d522189ad68fcb00aff05fd134bf20924
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add mxt nodes to dts and gpio-reset functionality.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Synchronize with commit fcfdb9c32075501e64751cc6a79fd91d15933692
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
To operate RS-485 on Toradex Carrier Boards a low active RTS signal
is required. Furthermore, a low active RTS signal requires the
receiver to be active (this seems to be a hardware limitation of the
i.MX UART).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Commit 95c163471135 ("usb: chipidea: use of extcon framework to
work for non OTG case") requires both pins to be specified (ID and
VBUS pin) to work correctly.
Fix the remaining dts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Initial add of Colibri iMX6 device tree, copied and adopted
from the Toradex toradex_4.1-2.0.x-imx branch.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
