summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
AgeCommit message (Collapse)Author
2017-06-07ARM: dts: imx6: Fix PCI GPIO reset polarityFabio Estevam
The imx6 PCI driver ignores the GPIO polarity from 'reset-gpio' and considers that the PCI reset is active low, unless the property 'reset-gpio-active-high' is present. Fix the device tree description by explicitly passing the 'GPIO_ACTIVE_LOW' flag to the 'reset-gpio' property. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-06-05ARM: dts: imx: Fix Ethernet PHY reset polarityFabio Estevam
The FEC driver ignores the GPIO polarity from 'phy-reset-gpios' and considers that the Ethernet PHY is active low, unless the property 'phy-reset-active-high' is present. Fix the device tree description by explicitly passing the 'GPIO_ACTIVE_LOW' flag to the 'phy-reset-gpios' property. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-01-02ARM: dts: imx: remove obsoleted property fsl,spi-num-chipselectsVladimir Zapolskiy
Since commit b36581df7e78 ("spi: imx: Using existing properties for chipselects") the device tree property 'fsl,spi-num-chipselects' is unused and it is already marked as obsolete in device tree binding documentation. Remove the property from the existing DTS files to avoid its reoccurence on copying. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-08-09ARM: dts: imx6qdl: don't configure reserved pad settingsUwe Kleine-König
Several dts files set a bit in the SPEED field for pads RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there doesn't have an effect and the bit reads as zero. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-07-22ARM: dts: fix STMicroelectronics compatible stringsStefan Agner
Replace the non-standard vendor prefix stm with st for STMicroelectronics. The drivers do not specify the vendor prefixes since the I2C Core strips them away from the DT provided compatible string. Therefore, changing existing device trees does not have any impact on device detection. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Rob Herring <robh@kernel.org>
2015-10-19ARM: dts: imx: add "jedec,spi-nor" flash compatible bindingRafał Miłecki
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor" binding indicating support for JEDEC identification. Use it for all flashes that are supposed to support READ ID op according to the datasheets. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2014-08-18ARM: dts: imx6: edmqmx6: change enet reset pinSilvio Fricke
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-18ARM: dts: imx6: edmqmx6: Add can busSilvio Fricke
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-18ARM: dts: imx6: edmqmx6: Add two other i2c busesSilvio Fricke
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-18ARM: dts: imx6: edmqmx6: Add PCIe supportSilvio Fricke
Add support for the PCI express bus available on MX6 Data Modul edm-qmx6 board. Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx6: edmqmx6: add vcc and vio power supplies to stmpeSilvio Fricke
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx6: edmqmx6: add SPI bus and flashLucas Stach
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx6: edmqmx6: add pinctrl for pfuze irq gpioLucas Stach
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Add stdout-path property to i.MX boardsSascha Hauer
This adds the stdout-path property to various i.MX boards. Values of the property have been taken from barebox, so they should be correct. Also, the older linux,stdout-path property is converted to stdout-path. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-14ARM: dts: imx6: edmqmx6: add second STMPELucas Stach
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-14ARM: dts: imx6: edmqmx6: USB H1 only supports host modeLucas Stach
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-14ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulatorSascha Hauer
GPIO7_12 switches the D+/D- USB lines on and off. When we use this as VBUS regulator it means that USB device mode can never work as VBUS is never turned on in Device mode. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-14ARM: dts: imx6: edmqmx6: Fix usbotg id pinLucas Stach
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-02-09ARM: dts: imx6: Add support for imx6q dmo edmqmx6Silvio F
Signed-off-by: Silvio F <silvio.fricke@gmail.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-04-28 16:30:47 +0000