summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi
AgeCommit message (Collapse)Author
2019-02-12MLK-11431-4: ARM: DTS: imx: Update IPU and display propertySandor Yu
Update IPU and display property, make sure these dts files can pass build. Signed-off-by: Sandor Yu <R01008@freescale.com>
2014-11-23ARM: dts: imx6: phyFLEX: Add CAN supportChristian Hemp
Add CAN support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01). Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-11-23ARM: dts: imx6: phyFLEX: Add PCIeChristian Hemp
Add PCIe support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01). Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-11-23ARM: dts: imx6: phyFLEX: Enable gpmi in module fileChristian Hemp
The nand is on the module (PFL-A-02) and not on the baseboard (PBA-B-01). Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-11-23ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boardsDmitry Lavnikevich
Audio on phyFLEX boards is presented by tlv320aic3007 codec connected over SSI interface. Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-11-23ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02Dmitry Lavnikevich
Since pins and frequency are specific to module (pfla02), not base board (pbab02), it is better to be initialized in corresponding dts file. This patch fixes i2c2, i2c3 pin configuration which caused messages: imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-05-16ARM: dts: pbab01: Enable DVIPhilipp Zabel
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Enable UART1Philipp Zabel
This patch enables UART1 on the phyFLEX connector (i.MX6 uart3). Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Add I2C devicesPhilipp Zabel
This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Add I2C2 and I2C3Philipp Zabel
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Set linux,stdout-path to UART4Philipp Zabel
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Add Phytec pbab01 with i.MX6 DualLite/SoloPhilipp Zabel
The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo phyFLEX i.MX6 modules (PFL-A-02). This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific device trees then just include the pfla01 and pbab01 dtsi files corresponding to the SoC variant. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-01 04:58:08 +0000