| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 032f85c9360fb1a08385c584c2c4ed114b33c260 ]
Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
|
|
The imx6 PCI driver ignores the GPIO polarity from 'reset-gpio' and
considers that the PCI reset is active low, unless the
property 'reset-gpio-active-high' is present.
Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'reset-gpio' property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit b36581df7e78 ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fixed code indent tabs in respetcive imx6qdl dtsi files.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SoC internal regulators for the CPU and the SoC come from the
DA9063 vdd_core and vdd_soc. Add this relationship to the device tree
so that the voltage drop on the SoC internal LDO regulators can be
minimized.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix a typo, replacing "pinctrl-name" by "pinctrl-names"
in the Phytec phyFLEX-i.MX6 Quad dtsi.
Also fix a typo in the board name
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The fixed-regulator bindings require a separate property enable-active-high,
the standard gpio phandle property polarity setting is ignored.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 4fe69a934b1f ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add CAN support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add PCIe support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The PMIC interrupt was changed from modul revision 1 to 2. Revision 1 was
declared as a prototype and is not in series by any customers.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The nand is on the module (PFL-A-02) and not on the baseboard (PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The gmpi and fec node were not in alphabatical order.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Audio on phyFLEX boards is presented by tlv320aic3007 codec connected
over SSI interface.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Since pins and frequency are specific to module (pfla02), not base board
(pbab02), it is better to be initialized in corresponding dts file.
This patch fixes i2c2, i2c3 pin configuration which caused messages:
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
standardise on 'dlg'
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The 2.5V VDD_ETH_IO voltage supplied by the DA9063 LDO4 is used
to power the KSZ9031 PHY DVDDH input and to pull the necessary
pins (including bootstrap pins) high.
It also powers the i.MX6 NVCC_RGMII and NVCC_ENET inputs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The pins labeled UART1 on the module connector are wired to i.MX6 uart3.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
