| Age | Commit message (Collapse) | Author |
|---|
|
Utilize the new DSA binding, introduced with commit 8c5ad1d6179d ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
PCIe has a range property, so the unit name should contain an address.
Make use of the label to enable individual PCIe busses. Also, fixup
the synology dtsi file which added a label pcie2 rather than using the
existing pcie1 label.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The dsa node does not have a reg property, so remove the address from
the unit name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The DT compiler is now warning about unit names with addresses but not
reg property. Fix all the gpio-key buttons which causes warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
During the conversion of boards to use DT to instantiate Distributed
Switch Architecture, nobody volunteered to test. As to be expected,
the conversion was flawed. Testers and access to hardware has now
become available, and this patch hopefully fixes the problems.
dsa,mii-bus must be a phandle to the top level mdio node, not the port
specific subnode of the mdio device.
dsa,ethernet must be a phandle to the port subnode within the ethernet
DT node, not the ethernet node.
Don't pinctrl hog the card detect gpio for mvsdio.
Rename the .dts files to make it clearer which file is for the Z0
stepping and which for the A0 or later stepping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: seugene@marvell.com
Tested-by: Eugene Sanivsky <seugene@marvell.com>
Fixes: e2eaa339af44: ("ARM: Kirkwood: convert rd88f6281-setup.c to DT.")
Fixes: e7c8f3808be8: ("ARM: kirkwood: Convert mv88f6281gtw_ge switch setup to DT")
Cc: <stable@vger.kernel.org> #v3.15+
Link: https://lkml.kernel.org/r/1409592941-22244-1-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
|
|
Merge "ARM: mvebu: DT changes for v3.16" from Jason Cooper:
mvebu DT changes for v3.16
- kirkwood
- rework nsa3x0 board to add nsa320
- large cleanup to facilitate use in barebox
- guruplug phy updates
- audio updates for t5325
- mvebu
- use clocks vice clock-frequency for uart nodes
- armada 375/380/385
- add watchdog node
- add coherency fabric
- add smp support
- add sdhci
- add ahci
- add thermal sensor
- armada 370/XP
- and pmsu
* tag 'mvebu-dt-3.16' of git://git.infradead.org/linux-mvebu: (35 commits)
ARM: Kirkwood: t5325: Use simple card to instantiate audio
ARM: Kirkwood: DT: Add missing #sound-dai-cells property
ARM: Kirkwood: Add node for audio codec
ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id
ARM: dts: kirkwood: set Guruplug ethernet PHY compatible
ARM: dts: kirkwood: set default pinctrl for I2C1 on 6282
ARM: dts: kirkwood: set default pinctrl for I2C0
ARM: dts: kirkwood: set default pinctrl for NAND
ARM: dts: kirkwood: set default pinctrl for SPI0
ARM: dts: kirkwood: set default pinctrl for UART0/1
ARM: dts: kirkwood: set default pinctrl for GBE1
ARM: dts: kirkwood: consolidate common pinctrl settings
ARM: dts: kirkwood: add pinctrl node to common SoC include
ARM: dts: kirkwood: rename pin-controller nodes
ARM: dts: kirkwood: remove clock-frequency properties from UART nodes
ARM: dts: kirkwood: add stdout-path property to all boards
ARM: dts: kirkwood: add node labels
ARM: mvebu: Enable the thermal sensor in Armada 380/385 SoC
ARM: mvebu: Enable the thermal sensor in Armada 375 SoC
ARM: mvebu: don't use clocks property in UART node for Netgear RN2120
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into fixes
Merge 'ARM: mvebu: DT fixes for v3.15 (incr #2)' from Jason Cooper:
mvebu DT fixes for v3.15 (incremental #2)
- kirkwood: fix mis-located pcie controller nodes
* tag 'mvebu-dt-fixes-3.15-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: fix mislocated pcie-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Most Kirkwood boards use the default SPI0 pinctrl setting anyway. Add a
default pinctrl setting to the toplevel SoC SPI0 node and put a note
in front of the corresponding pinctrl node to overwrite the setting
on board level.
Currently, only T5325 is using a different setting and already
overwrites the corresponding pinctrl node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-11-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Most boards use the default UART0/1 pinctrl setting without RTS/CTS.
Add the pinctrl setting to the toplevel SoC UART nodes and put a note
in front of the corresponding pinctrl node to overwrite the setting
on board level. Currently, both boards using a different UART pinctrl
setting (Openblocks A6, A7) already overwrite the pinctrl node.
While at it, also fix up some status = "ok" to "okay" and again
whitespace issues on mplcec4 uart nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-10-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
To prepare pin-controller consolidation, first rename all pinctrl nodes
to a more appropriate name regarding ePAPR recommended names.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-6-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
UART devices found on Kirkwood SoCs derive their baudrate from TCLK.
With proper clocks property in the SoCs serial node, boards do not
need to overwrite it anymore.
Remove the remaining clock-frequency property from all Kirkwood boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-5-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
ePAPR allows to reference the device used for console output by
stdout-path property. With node labels for Kirkwood UART0, now
reference it on all Kirkwood boards that already have ttyS0 in
their bootargs property.
While at it, fix some whitespace issues on mplcec4's chosen node
(there are more, but we only fix the chosen node now)
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-4-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Commit 54397d85349f
("ARM: kirkwood: Relocate PCIe device tree nodes")
moved the pcie-controller nodes for the Kirkwood SoCs to the mbus
bus node. For some reason, two boards were not properly converted
and have their pci-controller nodes still in the ocp bus node.
As the corresponding SoC pcie-controller does not exist anymore,
it is likely that pcie is broken on those boards since above commit.
Fix it by moving the pcie related nodes to the correct location.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Fixes: 54397d85349f ("ARM: kirkwood: Relocate PCIe device tree nodes")
Cc: <stable@vger.kernel.org> # v3.12+
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-2-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.infradead.org/linux-mvebu into fixes
mvebu DT fixes-non-critical (for v3.15-rc1)
- kirkwood
- add some missing vendor prefixes to keep checkpatch happy
- mvebu
- add clock ref to mdio node on 370/XP/38x
* tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: ensure the mdio node has a clock reference on Armada 38x
ARM: mvebu: ensure the mdio node has a clock reference on Armada 370/XP
ARM: Kirkwood: DT: Add missing vendor prefix
ARM: Kirkwood: Fix Atmel vendor prefix
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add vendor prefixes to compatible strings where they are missing.
Both the I2C and MTD framework ignore the prefix, so adding them has
no effect on backwards compatibility.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1395492360-1865-6-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The mv88f6281gtw_ge has a ethernet switch connected to the ethernet
port of the SoC. Convert the platform device instantiation to a DT
instantiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: florian@openwrt.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Replace the numeric key value with a symbolic name from
<bt-bindings/input/input.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit converts the mv88f6281gtw_ge Kirkwood board to use a
Device Tree representation, except for the Ethernet devices and the
DSA switch. Even though the mv643xx_eth driver has a DT binding,
converting this board to use it is for now left on the side because it
doesn't use a simple PHY, but a DSA switch instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
