| Age | Commit message (Collapse) | Author |
|---|
|
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Fix the following warnings from dtc by either adding or removing
the unit name from the node.
Warning (unit_address_vs_reg): Node /soc/flash-controller@40003000/flash@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@4 has a unit name, but no reg property
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Enable the DAC on the EA4357 dev kit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Enable adc0 on EA4357 dev kit. This kit has a 22k
potentiometer (R94) connected on ADC0 channel 3.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Add Freescale MMA7455 3-axis I2C accelerometer as found on
Embedded Artists' LPC4357 Developer's Kit to the device tree.
This makes it possible to access the accelerometer through
the API provided by IIO.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Add I2C0 and some of the I2C devices on the EA4357 dev kit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
The SSP0 can be found on the EA4357 Dev Kit on J15 pin 3-6.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
The EA4357 dev kit has a Spansion S25FL016K SPI-NOR Flash connected
to the SPIFI perherial.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Hook up LEDs on the outputs from the D-type flip-flop found on
the address/data bus.
Note that the LEDx label in the schematics is reversed in regard
to the bits on the data bus. Hence the reverse ordering used here.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Setup the emc pins used by external memory devices and add
configuration for the devices found on the EA4357 devkit.
The EA4357 devkit has a NOR Flash attached to chip select 0
and a D-type flip-flop used for LEDs on chip select 2.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable USB0 on the EA4357 devkit and setup the required USB0
control pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable UART3 that is routed to the J17 DSUB9 connector on
the EA4357 devkit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Enable Ethernet and add pin muxing and set the correct
frequency on the enet tx clock input.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Hook up the small joystick found on the EA4357 devkit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Enable the MMC/SD controller on EA4357 devkit and add pin
muxing plus a regulator.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Setup pin muxing and properties for the debug console on uart0.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.
More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.php
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
