| Age | Commit message (Collapse) | Author |
|---|
|
To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to PHYTEC PHYCORE-LPC3250 board dts
file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
To declare MTD OF partitions NAND controller device node should have
a special 'partitions' subnode, the change removes a debug message
from mtd/ofpart on boot:
nxp_lpc3220_slc: 'partitions' subnode not found on /ahb/flash@20020000.
Trying to parse direct subnodes as partitions.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change simplifies layout of PHY3250 board description by
referencing device nodes of LPC32xx controllers by label.
No functional change intended.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Preparatory change prior to disabling SSPx controllers
by default in the shared LPC32xx DTSI file.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change adds fixed voltage regulator for SD controller, ARM MMCI
controller driver uses it to control card power management.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Phytec PHY3250 board has GPIO controlled regulators for LCD and
backlight, add their descriptions to board DTS file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
NXP LPC32xx SoC has one USB OTG controller, which is supposed to work
with an external phy (default is NXP ISP1301).
Practically the USB controller contains 5 subdevices:
- host controller 0x3102 0000 -- 0x3102 00FF
- OTG controller 0x3102 0100 -- 0x3102 01FF
- device controller 0x3102 0200 -- 0x3102 02FF
- I2C controller 0x3102 0300 -- 0x3102 03FF
- clock controller 0x3102 0F00 -- 0x3102 0FFF
The USB controller can be considered as a "bus", because the
subdevices above are relatively independent, for example I2C
controller is the same as other two general purpose I2C controllers
found on SoC.
The change is not intended to modify any logic, but it rearranges
existing device nodes, in future it is planned to add a USB clock
controller device node into the same group.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
In case if SDRAM memory region is not populated by a bootloader,
provide this value in device trees for EA3250 and PHY3250 boards.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change replaces /include/ to #include in lpc32xx.dtsi and
derivatives, it is required, if C preprocessor is intended to be used
over dtsi/dts files, otherwise errors like one below are generated:
Error: ea3250.dts:15.1-9 syntax error
FATAL ERROR: Unable to parse input tree
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
This patch adjusts the PHY3250 board file to the actual LED configuration
(active high, default-state and trigger configuration).
Signed-off-by: Roland Stigge <stigge@antcom.de>
|
|
In spi-pl022.c, the new device tree binding is now "num-cs" for the number of
chip selects. Further, pl022,hierarchy and pl022,slave-tx-disable isn't
supported in favour of reasonable defaults in the driver.
Adjusting phy3250.dts to it.
Signed-off-by: Roland Stigge <stigge@antcom.de>
|
|
Add the reg, cs-gpios and max-frequencies that are needed for spi
device registry in phy3250.
Adds also the pl022 internal transfers details via dt
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
|
|
This patch fixes the DTS files for the High Speed UARTs 1, 2 and 7 of the
LPC32xx SoC, adjusting the compatible strings, adding interrupts and status
configuration. On the PHY3250 reference board, UART2 is enabled.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
|
|
This patch switches from static serial driver initialization to devicetree
configuration. This way, the Standard UARTs of the LPC32xx SoC can be enabled
individually via DT.
E.g., instead of Kconfig configuration, the phy3250.dts activates
UARTs 3 and 5.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
|
|
This patch adjusts the dts files to reference the pl18x primecell driver
correctly.
Signed-off-by: Roland Stigge <stigge@antcom.de>
|
|
This patch connects the lpc32xx-key driver to the LPC32xx platform (via
lpc32xx.dtsi), and more specifically to the reference board via its dts file.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
|
|
This patch adds necessary NAND flash timings to the board specific dts file of
the PHY3250 reference board of the LPC32xx SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
|
|
The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds the dts files for the reference machine of LPC32xx:
* arch/arm/boot/dts/lpc32xx.dtsi: Include for devices based on LPC32xx
* arch/arm/boot/dts/phy3250.dts: Board support for PHYTEC phyCORE-LPC3250
Signed-off-by: Roland Stigge <stigge@antcom.de>
|
