| Age | Commit message (Collapse) | Author |
|---|
|
We deprecated the "num-slots" property now and plan to get
rid of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Now that the rockchip usb phy has a vbus-supply property use that to
control the vbus regulator on rock2.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Rock 2 square board has a USB -> SATA converter hooked up to its usb
host1 connection. Enable the usb controller and always turn on the power
on the 5V sata power connector (controlled by gpio).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This commit adds the DT definition of the es8388 i2c device
found at address 0x10. It also adds the definition for connecting
the Rockchip I2S to the es8388 analog output.
This commit is based on the initial work that was done by Sjoerd Simons
<sjoerd.simons@collabora.com> with some improvements.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Use macros to describe gpios will make the dts easier to
read and write.
All the modifications done with sed:
sed -i -e 's/ 0 GPIO_ACTIVE_/ RK_PA0 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 1 GPIO_ACTIVE_/ RK_PA1 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 2 GPIO_ACTIVE_/ RK_PA2 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
.......
.......
sed -i -e 's/ 30 GPIO_ACTIVE_/ RK_PD6 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 31 GPIO_ACTIVE_/ RK_PD7 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
Tested with:
for i in dts-old/*dtb; do scripts/dtc/dtx_diff $i dts-new/$(basename $i); done
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[also adapted the gpio interrupts]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the sdio0 slot on the Rock2 square which has a broadcom wifi chip
attached and add a power sequence to enable the wifi chip and turn on
the required 32k clock.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Describe the two user-controllable LEDs on Rock2 Square boards.
All information have been retrieved from the schematics and the vendor
devicetree. The default-triggers mimic the behaviour of the vendor-kernel to
keep functionalities in sync.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add support for the IR receiver as present on the Radxa Rock 2 Square
board.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the SPDIF optical output on Radxa Rock2 square boards
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.
Currently supported are serial console, wired networking, hdmi output,
eMMC and SD storage and USB.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
