| Age | Commit message (Collapse) | Author |
|---|
|
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Cheap allwinner based devices in the q8 enclosure come in many variants,
all sharing the case and a number of other basic features.
They differ in the display, touchscreen, accelerometer and wifi chips
used.
This commit adds 2 dtsi files defining the shared features of all the
q8 tablets. sunxi-q8-common.dtsi defines features shared amongst all
q8 tablets, sun8i-q8-common.dtsi defines features shared amongst all
a23 / a33 based q8 tablets, but not with a13 q8 based tablets.
a13 based tablets use a different card-detect pin for the mmc, and
use uart1 instead of the r_uart for the serial console.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable the otg controller on Ippo Q8H tablets, for now it is enabled
in host-only mode, because true OTG support requires support for
detecting and enabling Vbus through the axp221 pmic.
For this to work the Vbus on the port must be enabled by u-boot,
or a powered hub must be used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The a23-ippo-q8h tablets have volume up/down buttons using the lradc. This
has been tested on both a v5 and a v1.2 tablet.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Prepare the device trees to use the C preprocessor.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Ippo q8h has its serial console connected to the r-uart. Adjust the
serial0 alias to match.
This fixes the kernel serial console no longer working since 3.19-rc1, because
8250_dw.c now honors dt aliases, causing the serial console to be ttyS5 rather
then being ttyS0, as it was in 3.18 and before.
Note that adjusting bootargs instead is not an acceptable fix, because
console=ttyS0,115200 is used by a lot of bootscripts, etc. and this should
continue to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
i2c0 is connected to the gsl1680 capacitive touch panel controller.
i2c1 is connected to an mma7660 3-axis accelerometer.
i2c2 is connected to the front and back gc0309 camera sensors.
The camera sensors require additional regulators be enabled before
they are available.
All these peripherals are not supported by the kernel yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The card detect pin setting was taken from the original fex file,
and is confirmed to work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we have R_PIO controller support and the pinmux for R_UART,
add the correct pinctrl properties to the R_UART node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets with A23 SoCs. There are at least 2 versions of the board, with
different peripherals, such as WiFi chips.
Common features among these tablets include 512 MB DRAM, NAND, MMC, LCD,
capacitive touchscreen, accelerometer, 1 or 2 camera sensors, USB OTG,
microphone and speaker.
v5 of these board designs has a ESP8089 WiFi chip (not supported)
connected to mmc1. This patch adds very basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
