summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts
AgeCommit message (Collapse)Author
2019-10-08ARM: dts: imx6ull-colibri: fix vqmmc regulatortoradex_4.9-1.0.x-imx-nexttoradex_4.9-1.0.x-imxMax Krummenacher
The correct spelling for the property is gpios, otherwise the regulator will neither reserve nor control any gpio(s). Thus any SD/MMC card which can use UHS 1 modes will fail. Related-to: #46566 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-06-05colibri-imx6ull: add fsl,tuning-start-tap propertyIgor Opaniuk
Specify the start dealy cell point when send first CMD19 in tuning procedure. This fixes these tunning procedure issues, and lets to use UHS-I mode properly: sdhci: Tuning procedure failed, falling back to fixed sampling clock mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00 Fixes: http://redmine.toradex.int/issues/46566 Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2018-12-11ARM: dts: imx6: add missing uart transceiver enable pinmuxPhilippe Schenker
This adds the enable-pin to uart2 that controls the transceiver for uart2/4. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-12-11ARM: dts: imx6ull: improve can templatesMax Krummenacher
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63 and move the inactive flexcan modes to imx6ull-colibri-eval-v3.dtsi where they belong. Note that this commit does not enable flexcan functionality, but rather eases the effort needed to do so. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-12-11ARM: dts: imx6ull: add sleep mode to fecPhilippe Schenker
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27ARM: dts: imx6ull-colibri: reduce v_batt current in power offColibri-iMX7_LXDE-Image_2.8b4.129-20181005Colibri-iMX6_LXDE-Image_2.8b4.129-20181005Colibri-iMX6ULL_LXDE-Image_2.8b4.129-20181005Apalis-iMX6_LXDE-Image_2.8b4.129-20181005Max Krummenacher
Reduce the current drawn from VCC_BATT when the main power on the 3V3 pins to the module are switched off. This switches off SoC internal pull resistors which are provided on the module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down instead of a pullup for the USBC_DET module pin (TAMPER2). Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27ARM: dts: imx7-colibri: disable HS400Stefan Agner
Force HS200 by masking bit 63 of the SDHCI capability register. The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With that the stack checks bit 63 to descide whether HS400 is available. Using sdhci-caps-mask allows to mask bit 63. The stack then selects HS200 as operating mode. This prevents rare communication errors with minimal effect on performance: sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL status REF not lock! Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27ARM: dts: imx6: remove 1.8V regulatorStefan Agner
There is no fixed 1.8V regulator. VDDD is connected to the PMIC. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27ARM: dts: imx6ull-colibri-aster: Add support for Aster with Colibri iMX6ULLMax Krummenacher
Add support for Aster Carrier Board with Colibri iMX6ULL. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27ARM: dts: imx7-colibri: unify settings for FlexCANMax Krummenacher
The current Colibri iMX7 device tree are prepared for flexcan1 and flexcan2. However their settings are different and the integration is done to a different degree. Unify that. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27imx6ull-colibri.dtsi: change touch i2c parametersMax Krummenacher
Switch on 22 kOhm pull ups and lower the I2C frequency to around 40kHz to get a more reliable communication. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-09-27imx6qdl-apalis.dtsi: card detect pins: use pull up and hysteresisMax Krummenacher
The apalis has a 8 and 4 bit SD/MMC interface. Switch on a 100k pull up on the card detect pins for carrier boards which leave the pin floating. Switch on hysteresis in case the signal has slow rise or fall times. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-07-20arm: dts: correct VDDA in SGTL5000 for imx6 modules.Gerard Salvatella
On imx6 the SGTL5000 audio codec supply voltage is 3.3V and not 2.5V as might have been copied over from other modules. Output is slightly overamplified if the value is not corrected, which may lead to signal clipping. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-07-20ARM: dts: Coibri iMX6ULL: use wdog HW signal for resetMax Krummenacher
The i.MX6 ULL's watchdog is used to reset the SoC on reboot. The watchdog is configured to use the SoC's internal reset signal which does not generate a reset pulse on nRESET_OUT. Change the watchdog configuration to use a SoC external HW signal. This will additionally change the 'Reset cause' message from U-Boot from WDOG to POR. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-06-26ARM: dts: imx6: mux SD/MMC CD and SPI CS explicitlyColibri-iMX7_LXDE-Image_2.8b3.111-20180627Colibri-iMX6_LXDE-Image_2.8b3.111-20180627Colibri-iMX6ULL_LXDE-Image_2.8b3.111-20180627Apalis-iMX6_LXDE-Image_2.8b3.111-20180626Stefan Agner
Use a pinmux configuration for SD/MMC card detect and SPI chip select instead of relying on reset/boot settings. There have been no adverse effects observed, but it seems sensible to mux the pads explicitly. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21Revert "ARM: dts: colibri-imx7: limit eMMC SDHC frequency to 100MHz"Stefan Agner
This reverts commit 5f60d82d38a8af8529d1493463e301e548595ccb. Several modules have issues with HS400 at 100MHz at room temperature but they seem to work fine at HS400 at 200MHz. Do not restrict frequency for now. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21dts: imx: colibri eval/iris: change pins to capacitive touch adapterMax Krummenacher
The Capacitive Touch Adapter is an interface board designed to easily connect the Capacitive Touch Display 7" Parallel to the Colibri Carrier boards which do not have PCAP connector yet available on board. Change the pins for interrupt and reset to those defined in the Capacitive Touch Adapter's datasheet. While at it remove the '#ifdef PCAP' in favour of disabled nodes. That way one can fixup the device tree in U-Boot to disable the pwm nodes and enable the connected touch controller. e.g. for a Colibri iMX6S/DL: Colibri iMX6 # setenv fdt_fixup 'fdt addr ${fdt_addr_r} && fdt resize && fdt set /soc/aips-bus@02100000/i2c@021a8000/atmel_mxt_ts@4a status okay; fdt set /soc/aips-bus@02000000/pwm@02080000 status disabled; fdt set /soc/aips-bus@02000000/pwm@0208c000 status disabled' Colibri iMX6 # saveenv Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-06-21dts: imx: fix M41T0 RTC compatible stringGerard Salvatella
Toradex Carrier boards use the ST M41T0 RTC (not M41T00). The RTC is almost the same, but the M41T0 needs some special handling in case the oscillator fails. Now that support for this difference is available, using the new compatible string to make use of it. Sync with commit 10e718b1c60c4e490e6972cfa58e97fcf5260685 Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21dts: add can-spi controllerGerard Salvatella
Synced with 558d378d522189ad68fcb00aff05fd134bf20924 Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21dts: update/add atmel mxtGerard Salvatella
Add mxt nodes to dts and gpio-reset functionality. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21dts: enable hdmi also on asterGerard Salvatella
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21dts: synchronize snvs node pathGerard Salvatella
Synchronize with commit fcfdb9c32075501e64751cc6a79fd91d15933692 Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21ARM: dts: imx7-colibri: prepare module device tree for FlexCANStefan Agner
Prepare FlexCAN use on SODIMM 55/63. Those SODIMM pins are compatible for CAN bus use with several modules from the Colibri family. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21ARM: dts: imx6qdl: Fix SPDIF regressionFabio Estevam
Commit 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif") changed many more clocks than only the SPDIF core clock as stated in the commit message. The MLB clock has been added and this causes SPDIF regression as reported by Xavi Drudis Ferran and also in this forum post: https://forum.digikey.com/thread/34240 The MX6Q Reference Manual does not mention that MLB is a clock related to SPDIF, so change it back to a dummy clock to restore SPDIF functionality. Thanks to Ambika for providing the fix at: https://community.nxp.com/thread/387131 Fixes: 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif") Cc: <stable@vger.kernel.org> # 4.4.x Reported-by: Xavi Drudis Ferran <xdrudis@tinet.cat> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Xavi Drudis Ferran <xdrudis@tinet.cat> Signed-off-by: Shawn Guo <shawnguo@kernel.org> (cherry picked from commit f065e9e4addd75c21bb976bb2558648bf4f61de6) This fix was correct, but overwritten by commit 833f2cbf7091099baee28136dc68678e974c0ac5. MLB (Media Local Bus) Clock is in fact not related to SPDIF according to the MX6Q Reference Manual. Tested playback and record on pulseaudio with 44.1kHz samples. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-21ARM: dts: imx: fix PCI bus dtc warningsRob Herring
dtc recently added PCI bus checks. Fix these warnings. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> (cherry picked from commit 3e1b857786f0d46a92b3a4d7878767883ed90bdc)
2018-06-21ARM: dts: imx6: add required RS-485 propertiesStefan Agner
To operate RS-485 on Toradex Carrier Boards a low active RTS signal is required. Furthermore, a low active RTS signal requires the receiver to be active (this seems to be a hardware limitation of the i.MX UART). Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-06-19Merge branch 'fslc_4.9-1.0.x-imx' into toradex_4.9-1.0.x-imx-nextMax Krummenacher
2018-03-23ARM: dts: imx6ull-colibri-eval-v3: remove duplicate nodesStefan Agner
Remove duplicate nodes introduced with the move to L4.9.11 release. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23arm: dts: apalis imx6: fix mipi-csi2 gpio assignmentMax Krummenacher
The new Apalis iMX6 Mezzanine board allows access to the MIPI-CSI2 interface from the evaluation board. The current device tree has different GPIO pin assignments for the camera reset and power pins. Change the pin assignment to use Apalis GPIO1 for reset and Apalis GPIO2 for power down. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23arm: dts: apalis imx6: add timings for new 10 inch lvdsMax Krummenacher
Add timings for LTTD1280800101-L4WH-CT1 panel used in the new Capacitive Touch 10.1" LVDS display. Note that the color mapping is to be set as follows: fsl,data-mapping = "spwg"; fsl,data-width = <24>; Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23arm: dts: apalis imx6: add reset controller for atmel mxt multitouchMax Krummenacher
The Atmel maXTouch multitouch controller driver does not control the reset line connected to the chip. Use a GPIO reset controller node to release the reset line and make the controller work. Note that both the reset controller's and the mxt mutitouch controller's node are set to disabled. Either change this in the dtsi source or fix this from U-Boot if you use an Atmel maXTouch multitouch controller. setenv fdt_fixup 'fdt addr ${fdt_addr_r} && fdt set /soc/aips-bus@02100000/i2c@021a0000/atmel_mxt_ts@4a status okay && fdt set /mxt-reset status okay' Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23ARM: dts: imx7: add alias for Ethernet controllersStefan Agner
Add alias for Ethernet controllers. This allows code to determine id of controllers using of_alias_get_id. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-03-23ARM: dts: imx7-colibri: Specify cable detect as ID and VBUS pinMax Krummenacher
Commit 95c163471135 ("usb: chipidea: use of extcon framework to work for non OTG case") requires both pins to be specified (ID and VBUS pin) to work correctly. Fix the remaining dts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23ARM: dts: imx6-colibri: Specify cable detect as ID and VBUS pinMax Krummenacher
Commit 95c163471135 ("usb: chipidea: use of extcon framework to work for non OTG case") requires both pins to be specified (ID and VBUS pin) to work correctly. Fix the remaining dts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23ARM: dts: imx6ull-colibri: Specify cable detect as ID and VBUS pinMax Krummenacher
Commit 95c163471135 ("usb: chipidea: use of extcon framework to work for non OTG case") requires both pins to be specified (ID and VBUS pin) to work correctly. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-03-23Merge remote-tracking branch 'remotes/fslc/4.9-1.0.x-imx' into ↵Marcel Ziswiler
toradex_4.9-1.0.x-imx-next
2018-03-12Merge tag 'v4.9.87' into fslc_4.9-1.0.x-imxMax Krummenacher
This is the 4.9.87 stable release Conflicts: drivers/dma/fsl-edma.c
2018-03-11ARM: dts: LogicPD Torpedo: Fix I2C1 pinmuxAdam Ford
commit 74402055a2d3ec998a1ded599e86185a27d9bbf4 upstream. The pinmuxing was missing for I2C1 which was causing intermittent issues with the PMIC which is connected to I2C1. The bootloader did not quite configure the I2C1 either, so when running at 2.6MHz, it was generating errors at time. This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-11ARM: dts: LogicPD SOM-LV: Fix I2C1 pinmuxAdam Ford
commit 84c7efd607e7fb6933920322086db64654f669b2 upstream. The pinmuxing was missing for I2C1 which was causing intermittent issues with the PMIC which is connected to I2C1. The bootloader did not quite configure the I2C1 either, so when running at 2.6MHz, it was generating errors at times. This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-08Merge remote-tracking branch 'linux-fslc/4.9-1.0.x-imx' into ↵Stefan Agner
toradex_4.9-1.0.x-imx-next Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-03-08ARM: dts: imx6: use SNVS RTC labelStefan Agner
The SNVS RTC does not use an address in its node name anymore. Instead of using the full path, simply use the SNVS RTC label. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-03-08ARM: dts: imx7-colibri: add alias for RTC and disable SNVS powerkeyStefan Agner
The SNVS subnodes reenable the power key which is not used on the Colibri iMX7 modules. Disable the power key again. Also make sure that the priority of the RTCs used is defined. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-03-08ARM: dts: imx7: add SNVS subnodesStefan Agner
Add SNVS subnodes such as internal SNVS RTC. Fixes: b66e57551f4e ("ARM: dts: imx7d: move nodes to i.MX 7Solo device tree") Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-03-08ARM: dts: imx7-colibri-emmc: remove operating pointsStefan Agner
The operating points are already present in imx7d.dtsi, there is no need to dupplicate the operating points in the module level device tree. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-03-08ARM: dts: imx7s: add operating pointsStefan Agner
The i.MX Thermal driver requires a cpufreq device to be present. Create a single operating point to make sure cpufreq device can successfully probe. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-03-03ARM: dts: ls1021a: fix incorrect clock referencesArnd Bergmann
[ Upstream commit 506e8a912661c97b41adc8a286b875d01323ec45 ] dtc warns about two 'clocks' properties that have an extraneous '1' at the end: arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1]) Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1]) The clocks that get referenced here are fixed-rate, so they do not take any argument, and dtc interprets the next cell as a phandle, which is invalid. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-26Merge tag 'v4.9.84' into 4.9-1.0.x-imx-stable-mergeFabio Estevam
This is the 4.9.84 stable release
2018-02-25ARM: dts: Fix elm interrupt compiler warningTony Lindgren
[ Upstream commit d364b038bc962f494cffb8f6cb6cddbe41bcb5b6 ] Looks like the interrupt property is missing the controller and level information causing: Warning (interrupts_property): interrupts size is (4), expected multiple of 12 in /ocp/elm@48078000 Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-25ARM: dts: am437x-cm-t43: Correct the dmas property of spi0Peter Ujfalusi
[ Upstream commit ca41e244517d6d3f1600c229ff7ca615049c1e9c ] The DMA binding for eDMA needs 2 parameters, not 1. The second, missing parameter is the tptc to be used for the channel. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-25ARM: dts: am4372: Correct the interrupts_properties of McASPPeter Ujfalusi
[ Upstream commit 627395a6f8091c0aa18f49dca7df59ba3ec147ef ] Fixes the following warnings: arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property): interrupts size is (8), expected multiple of 12 in /ocp@44000000/mcasp@48038000 arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property): interrupts size is (8), expected multiple of 12 in /ocp@44000000/mcasp@4803C000 Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-04-16 22:17:17 +0000