Age | Commit message (Collapse) | Author |
|
Related-to: ELB-2300
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Leave reset line setup to the capacitive touch drivers.
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
In order to avoid any floating SD card detect pins as may e.g. happen on
Ixora V1.1A pull them all up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
|
|
Adds compile time option to enable support for
Toradex Capacitive Touch Adapter.
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add SPI controller platform data required for use of hardware chip
selects.
While at it pull-up SPI chip select pin due to NVIDIA's designers
taking the term chip select a little too personal: they indeed only
select a chip otherwise all the chip select pins are just left
floating!
|
|
Due to a strong pull-down on the menu-key multiplexed ACC1_DETECT pin
Android unintentionally entered safe-mode. Fix this by making the
menu-key active-high as well.
|
|
Integrate CAN support for the Colibri Evaluation Board V3.1a with built-in
MCP2515 SPI CAN controller resp. the Colibri Evaluation Board V2.1c with its
built-in SJA1000 CAN controller connected to the GMI bus.
The following kernel configuration needs to be enabled as well:
CONFIG_CAN
CONFIG_CAN_RAW
CONFIG_CAN_BCM
CONFIG_CAN_DEV
Plus depending on the Evaluation Board revision:
CONFIG_CAN_MCP251X
or
CONFIG_CAN_SJA1000
CONFIG_CAN_SJA1000_PLATFORM
Optional support for 32-bit GMI as well as xPOD CAN on MECS Tellurium for
Colibri T20 is provided via commented defines in
arch/arm/mach-tegra/board-colibri_t20.h.
|
|
Looks like we mixed up the low-active buffer enable GPIOs. This fixes
GMI_WR_N on SODIMM pin 93 RDnWR curtsey Tord Andersson from Endian
Technologies AB.
|
|
As the new Colibri Evaluation carrier board v3.1a uses SODIMM pin 45 as
IrDA transceiver SD with a 100 K pull-down we revert to using the power
key as high active.
|
|
GPIO keys configured as active-low either require pull-ups on the
carrier board or via pin-muxing. We enable the later for now.
|
|
Use GPIO inputs for function tri-stating rather than pin group
tri-stating to avoid influencing neighbouring pins.
While at it get rid of most pull-up/downs and a lot of commented out
stuff.
|
|
Rename CAMERA_INTERFACE to COLIBRI_T20_VI which stands for video input
to be more in-line with Colibri T30.
|
|
SODIMM pin 135 is really GPIO K6 multiplexed with ACC1_DETECT. Unfortunately the later can't be tri-stated but since it is anyway always an input it should not interfere. Please note however that this SODIMM pin is rather low resistance.
|
|
Fix PWM backlight by using PWM<A> rather than PWM<C> by default.
Invert brightness value due to unified TFT interface displays (e.g. EDT
ET070080DH6) inverted LEDCTRL pin behaviour (e.g. 0V brightest vs. 3.3V
darkest) and use PWM frequency of 1 kHz as recommended.
Add comment about PWM pin muxing.
While at it do some ifdef and indentation clean-up.
|
|
Incorporate L4T R16 changes from NVIDIA Ventana.
Note: USB OTG port not functional as of yet.
|
|
|