summaryrefslogtreecommitdiff
path: root/arch/arm/plat-mxc/include
AgeCommit message (Collapse)Author
2011-11-11plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desiredPaul Fertser
commit 6571534b600b8ca1936ff5630b9e0947f21faf16 upstream. To configure pads during the initialisation a set of special constants is used, e.g. #define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP) The problem is that no pull-up/down is getting activated unless both PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module enable) set. This is clearly stated in the i.MX25 datasheet and is confirmed by the measurements on hardware. This leads to some rather hard to understand bugs such as misdetecting an absent ethernet PHY (a real bug i had), unstable data transfer etc. This might affect mx25, mx35, mx50, mx51 and mx53 SoCs. It's reasonable to expect that if the pullup value is specified, the intention was to have it actually active, so we implicitly add the needed bits. Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-08iMX: Fix build for iMX53Arnaud Patard (Rtp)
Commit fad107086d5a869c1c07e5bb35b7b57a10ecf578 fixed the wrong test for MX51 as the MX51 addresses are wrong for MX50 and MX53 but now it's MX51 only, UART_PADDR is not defined anymore when building for MX50/MX53. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Tested-by: Steev Klimaszewski <steev@genesi-usa.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-08-08Merge commit 'v3.1-rc1' into imx-fixesSascha Hauer
2011-07-27dmaengine: imx-sdma: use platform_device_id to identify sdma versionShawn Guo
It might be not good to use software defined version to identify sdma device type, when hardware does not define such version. Instead, soc name is stable enough to define the device type. The patch uses platform_device_id rather than version number passed by platform data to identify sdma device type/version. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Vinod Koul <vinod.koul@intel.com>
2011-07-27mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()Shawn Guo
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes platform_device_id to distinguish the esdhc differences among SoCs. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Wolfram Sang <w.sang@pengutronix.de> Cc: Chris Ball <cjb@laptop.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5Shawn Guo
The patch extends card_detect and write_protect support to get mx5 family and more scenarios supported. The changes include: * Turn platform_data from optional to mandatory * Add cd_types and wp_types into platform_data to cover more use cases * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD * Adjust some machine codes to adopt the platform_data changes * Work around the issue that software reset will get card detection circuit stop working With this patch, card_detect and write_protect gets supported on mx5 based platforms. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Chris Ball <cjb@laptop.org> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Chris Ball <cjb@laptop.org>
2011-07-27net/fec: gasket needs to be enabled for some i.mxShawn Guo
On the recent i.mx (mx25/50/53), there is a gasket inside fec controller which needs to be enabled no matter phy works in MII or RMII mode. The current code enables the gasket only when phy interface is RMII. It's broken when the driver works with a MII phy. The patch uses platform_device_id to distinguish the SoCs that have the gasket and enables it on these SoCs for both MII and RMII mode. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reported-by: Troy Kisky <troy.kisky@boundarydevices.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: David S. Miller <davem@davemloft.net>
2011-07-26Merge branch 'next/devel' of ↵Linus Torvalds
ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (128 commits) ARM: S5P64X0: External Interrupt Support ARM: EXYNOS4: Enable MFC on Samsung NURI ARM: EXYNOS4: Enable MFC on universal_c210 ARM: S5PV210: Enable MFC on Goni ARM: S5P: Add support for MFC device ARM: EXYNOS4: Add support FIMD on SMDKC210 ARM: EXYNOS4: Add platform device and helper functions for FIMD ARM: EXYNOS4: Add resource definition for FIMD ARM: EXYNOS4: Change devname for FIMD clkdev ARM: SAMSUNG: Add IRQ_I2S0 definition ARM: SAMSUNG: Add platform device for idma ARM: EXYNOS4: Add more registers to be saved and restored for PM ARM: EXYNOS4: Add more register addresses of CMU ARM: EXYNOS4: Add platform device for dwmci driver ARM: EXYNOS4: configure rtc-s3c on NURI ARM: EXYNOS4: configure MAX8903 secondary charger on NURI ARM: EXYNOS4: configure ADC on NURI ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs ... Fix up tons of silly conflicts: - arch/arm/mach-davinci/include/mach/psc.h - arch/arm/mach-exynos4/Kconfig - arch/arm/mach-exynos4/mach-smdkc210.c - arch/arm/mach-exynos4/pm.c - arch/arm/mach-imx/mm-imx1.c - arch/arm/mach-imx/mm-imx21.c - arch/arm/mach-imx/mm-imx25.c - arch/arm/mach-imx/mm-imx27.c - arch/arm/mach-imx/mm-imx31.c - arch/arm/mach-imx/mm-imx35.c - arch/arm/mach-mx5/mm.c - arch/arm/mach-s5pv210/mach-goni.c - arch/arm/mm/Kconfig
2011-07-26Merge branch 'next/cross-platform' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: ARM: Consolidate the clkdev header files ARM: set vga memory base at run-time ARM: convert PCI defines to variables ARM: pci: make pcibios_assign_all_busses use pci_has_flag ARM: remove unnecessary mach/hardware.h includes pci: move microblaze and powerpc pci flag functions into asm-generic powerpc: rename ppc_pci_*_flags to pci_*_flags Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
2011-07-26ARM: mx53: add pad configuration for I2C signalsEric Miao
I2C signals SDA/SCL are a bit different, they need to be pull-up and open-drain (so to support multiple I2C devices). Signed-off-by: Richard Zhao <richard.zhao@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-25Merge branch 'next/cleanup' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits) ARM: EXYNOS4: Change devname for FIMD clkdev ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210 ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100 ARM: S3C24XX: Use generic s3c_set_platdata for devices ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND ARM: SAMSUNG: Use generic s3c_set_platdata for NAND ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON ARM: SAMSUNG: Use generic s3c_set_platdata for FB ARM: SAMSUNG: Use generic s3c_set_platdata for TS ARM: S3C64XX: Add PWM backlight support on SMDK6410 ARM: S5P64X0: Add PWM backlight support on SMDK6450 ARM: S5P64X0: Add PWM backlight support on SMDK6440 ARM: S5PC100: Add PWM backlight support on SMDKC100 ARM: S5PV210: Add PWM backlight support on SMDKV210 ARM: EXYNOS4: Add PWM backlight support on SMDKC210 ARM: EXYNOS4: Add PWM backlight support on SMDKV310 ARM: SAMSUNG: Create a common infrastructure for PWM backlight support clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0 ... Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
2011-07-25Merge branch 'next/fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits) ARM: msm: platsmp: determine number of CPU cores at boot time ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461 ARM: Tegra: Trimslice: Tri-state DAP3 pinmux ARM: orion5x: fixup 5181 MPP mask check ARM: mxs-dma: include <linux/dmaengine.h> ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts ARM: i.MX53: UARTn_CTS pin should not change RTS input select ARM: i.MX53: UARTn_TXD pin should not change RXD input select ARM: mx25: Fix typo on CAN1_RX pad setting iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed ARM: i.MX53: Fix IOMUX type o's ARM i.MX dma: Fix burstsize settings mach-mx5: fix the I2C clock parents ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0 ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h ARM: mx53: Fix some interrupts marked as reserved. MXC: iomux-v3: correct NO_PAD_CTRL definition ... Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
2011-07-24Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits) ARM: 7004/1: fix traps.h compile warnings ARM: 6998/2: kernel: use proper memory barriers for bitops ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM ARM: Fix build errors caused by adding generic macros ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU ARM: CPU hotplug: pass in proper affinity mask on IRQ migration ARM: GIC: avoid routing interrupts to offline CPUs ARM: CPU hotplug: fix abuse of irqdesc->node ARM: 6981/2: mmci: adjust calculation of f_min ARM: 7000/1: LPAE: Use long long printk format for displaying the pud ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence ARM: ARM_DMA_ZONE_SIZE is no more ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ...
2011-07-19ARM: Consolidate the clkdev header filesKyungmin Park
Now most of ARM machines has the alsmot same __clk_get/put() macro So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config Now there are only 3 caese. 1) define the clk structure with clkdev macro => Need to move clk structure to proper header file arch/arm/mach-versatile/include/mach/clkdev.h arch/arm/mach-realview/include/mach/clkdev.h arch/arm/mach-vexpress/include/mach/clkdev.h arch/arm/mach-integrator/include/mach/clkdev.h 2) export the __clk_get/put function at clock.c arch/arm/mach-shmobile/include/mach/clkdev.h 3) demuxing the clk source arch/arm/mach-u300/include/mach/clkdev.h Acked-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2011-07-15Merge branch 'fixes-for-arnd' of git://git.pengutronix.de/git/imx/linux-2.6 ↵Arnd Bergmann
into imx/fixes
2011-07-15ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/ctsTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-15ARM: i.MX53: UARTn_CTS pin should not change RTS input selectTroy Kisky
If both the RTS pad and CTS pad definitions setup IOMUXC_UARTn_IPP_UART_RTS_MUX_SELECT_INPUT, then the order of setup will matter. We don't want that. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-15ARM: i.MX53: UARTn_TXD pin should not change RXD input selectTroy Kisky
If both the RXD pad and TXD pad definitions setup IOMUXC_UARTn_IPP_UART_RXD_MUX_SELECT_INPUT, then the order of setup will matter. We don't want that. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-15ARM: mx25: Fix typo on CAN1_RX pad settingFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-15iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitionsLothar Waßmann
The I2C controller requires the SION bit to be set on SDA and SCL pins. This is missing on some pad definitions for the I2C function. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-08ARM: mxc: use ARCH_NR_GPIOS to define gpio numberShawn Guo
The patch removes MXC_GPIO_IRQS and instead uses ARCH_NR_GPIOS to define gpio number. This change is need when we change mxc gpio driver to be device tree aware. When migrating the driver to device tree, pdev->id becomes unusable. It requires driver get gpio range from gpio core, which will dynamically allocates number from ARCH_NR_GPIOS to 0. As a bonus point, it removes lines of '#if' and make the code a little bit cleaner. The side effect is the waste of number. But this is not a point when we go single image. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-08gpio/mxc: get rid of the uses of cpu_is_mx()Shawn Guo
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes platform_device_id to distinguish the different gpio types, IMX1_GPIO on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other i.mx SoCs. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-07ARM: mx53: Add SSI suportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mx53: Add support for missing UARTsFabio Estevam
MX53 has five UART ports. Add support for the missing UART4 and UART5 ports. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07dmaengine: imx-sdma: pass sdma firmware name via platform dataShawn Guo
It is not good to have cpu_name and to_version encoded into sdma firmware name as variables. For example, there are three TOs of imx51 soc, the sdma script never changes since TO1, which means all three TOs of imx51 uses TO1 version of sdma script. But we have to prepare three identical firmwares, sdma-imx51-to1.bin sdma-imx51-to2.bin and sdma-imx51-to3.bin, to have the kernel capable of running on all three TOs. The patch removes cpu_name and to_version from sdma platform data, and instead uses fw_name to pass the firmware name, so that we can pass the TO version where it's relevant and skip it where only one firmware exists. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mxc: clean up imx-dma device registrationShawn Guo
The patch follows the implementation of gpio-mxc device registration to break the concentrated imx-dma device registration into soc specific setup function. Then we can avoid the churn of "#ifdef" and the cpu_is_mx checking on such a long list, which makes no sense, considering more soc supports need to be added and we need to support single image for multiple socs in the long run. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mach-mx5/mx53_ard: Add support for i.MX53 ARD boardAndre Silva
Signed-off-by: Andre Silva <andre.silva@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07Merge remote-tracking branch 'grant/gpio/next-mx' into devel-featuresSascha Hauer
Conflicts: arch/arm/mach-imx/mach-mx31_3ds.c arch/arm/mach-imx/mach-scb9328.c Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM i.MX debug macro: use CONFIG_SOC_* instead of CONFIG_ARCH_*Sascha Hauer
CONFIG_ARCH_* are deprecated, so remove one user. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM i.MX: get rid of wrong MXC_INTERNAL_IRQ usageSascha Hauer
There are several occurences where MXC_INTERNAL_IRQ is assumed to be the start of the gpio interrupts. It was never meant this way. Replace these with gpio_to_irq. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-07-07ARM i.MX mxc.h: use CONFIG_SOC_* instead of CONFIG_ARCH_*Sascha Hauer
CONFIG_ARCH_* are deprecated, so remove one user. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM i.MX: remove SoC defines around header includesSascha Hauer
All soc specific header have proper namespace now and thus can be included at once. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM i.MX: define CLOCK_TICK_RATE to bogus valueSascha Hauer
We have a clocksource which renders CLOCK_TICK_RATE useless. Define it to a bogus value to get rid of some ifdeffery. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM i.MX: fix last user of iomux.h and remove itSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: i.MX53: Fix IOMUX type o'sTroy Kisky
", o" was used for ", 0" ", 17" was used for ", 7 | 0x10" Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mx53: Fix some interrupts marked as reserved.Fabio Estevam
Mark the actual interrupt source for some interrupts currently marked as reserved. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07MXC: iomux-v3: correct NO_PAD_CTRL definitionTroy Kisky
iomux-v3.c uses NO_PAD_CTRL as a 32 bit value so it should not be shifted left by MUX_PAD_CTRL_SHIFT(41) Previously, anything requesting NO_PAD_CTRL would get their pad control register set to 0. Since it is a pad control mask, place it with the other mask values. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Lothar Waßmann <LW@KARO-electronics.de> Tested-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07mxc: iomuxv1: Do not use gpio_request when setting the pin as GPIOFabio Estevam
When setting the IOMUX of multiple pins via mxc_gpio_setup_multiple_pins, gpio_request is called and this prevents subsequent calls of gpio_request done by drivers to succeed. Remove gpio_request call from mxc_gpio_setup_multiple_pins function. As gpio_request is removed from mxc_gpio_setup_multiple_pins, there is no need to have mxc_gpio_release_multiple_pins anymore, so remove this function. Tested on a mx27_3ds board and after applying this patch it is possible to define all the IOMUX setup in a static array Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mx53: Fix the base addresses for the DDR memory regionsMarc Kleine-Budde
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mx53: Fix the chip select addressesFabio Estevam
MX53 has 4 chip selects (CS0 - CS3) and the valid combinations are: - CS0 (128MB) - CS0 (64MB), CS1 (64MB) - CS0 (64MB), CS1 (32MB), CS2 (32MB) - CS0 (32MB), CS1 (32MB), CS2 (32MB) , CS3 (32MB) Fix these addresses and also take into account all the four possibilities. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mx53: Fix alternate modes for MX53_PAD_PATA_DATA6Fabio Estevam
MX53_PAD_PATA_DATA6 can have the following alternate modes: PATA_DATA_6: mode 0 GPIO2_6: mode 1 EMI_NANDF_D_6: mode 3 ESDHC4_DAT6 mode 4 GPU3d_GPU_DEBUG_OUT_6 mode 5 IPU_DIAG_BUS_6 mode 6 Fix the modes accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Dinh Nguyen <dinh.nguyen@freescale.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-06-28ARM: entry: remove unused irq_prio_table macroRussell King
Platforms provide an empty irq_prio_table macro, and as nothing uses this macro, it can simply be removed. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-06-06gpio/mxc: Change gpio-mxc into an upstanding gpio driverShawn Guo
The patch makes necessary changes on gpio-mxc as below to turn it into an upstanding gpio driver. * Add a list to save all mx2 ports references, so that mx2_gpio_irq_handler can walk through all interrupt status registers * Use readl/writel to replace mach-specific accessors __raw_readl/__raw_writel * Change mxc_gpio_init into mxc_gpio_probe function * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to be public at all, and also make some other cleanup on plat-mxc/include/mach/gpio.h at the same time And the patch then migrates mach-imx and mach-mx5 to the updated driver by adding corresponding platform devices. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into ↵Russell King
devel-stable
2011-05-19ARM: imx: remove some deprecated and unused #definesUwe Kleine-König
LAKML-Reference: 1302464943-20721-6-git-send-email-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-05-19ARM: mx3: make ioremap quirk ready for multi-SoC kernelsUwe Kleine-König
To be able to compile e.g. i.MX31 and i.MX51 in a single kernel image the ioremap quirk needs a runtime check. While touching this code make the comment more understandable by adding a sentence from the commit log that introduced it (eadefef ([ARM] MX3: Use ioremap wrapper to map SoC devices nonshared)). As mach/io.h now uses cpu_is_ some header reshuffling in mach/hardware.h was necessary. (mach/mx27.h and mach/mx31.h #include <linux/io.h> which #includes <mach/io.h>. So mach/mxc.h which provides the cpu_is_ macros needs to be included before mach/mx27.h and mach/mx31.h.) LAKML-Reference: 1302464943-20721-5-git-send-email-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-05-19ARM: remove support for mxc91231Uwe Kleine-König
Since support for mxc91231 was introduced 2009 it only saw patches that were part of (mxc or arm) global cleanups. The only supported machine only had 4 devices (2x UART, sdhc, watchdog). Cc: Dmitriy Taychenachev <dimichxp@gmail.com> LAKML-Reference: 1302211482-17926-1-git-send-email-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-05-19ARM: mx3: dynamically allocate "ipu-core" devicesUwe Kleine-König
... together with the related devices "mx3_camera" and "mx3_sdc_fb". "mx3_camera" doesn't fit the scheme of the other devices that just are allocated and registered in a single function because it needs additional care to get some dmaable memory. So currently imx31_alloc_mx3_camera duplicates most of imx_add_platform_device_dmamask, but I'm not sure it's worth to split the latter to be able to reuse more code. This gets rid of mach-mx3/devices.[ch] and so several files need to be adapted not to #include devices.h anymore. LAKML-Reference: 1299271882-2130-5-git-send-email-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-05-19ARM: mx3: dynamically allocate "mxc_rtc" devicesUwe Kleine-König
LAKML-Reference: 1299271882-2130-2-git-send-email-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-05-19ARM: imx/mx25: add NAND chip select pins to iomuxBaruch Siach
Signed-off-by: Baruch Siach <baruch@tkos.co.il> LAKML-Reference: cae1d71db47204ee2654eca7391cb656ed53566b.1300095569.git.baruch@tkos.co.il Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-10 06:35:49 +0000