| Age | Commit message (Collapse) | Author |
|---|
|
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Conflicts:
arch/arm/Kconfig
arch/arm/mach-ns9xxx/include/mach/uncompress.h
|
|
Convert SP804, MXC, Nomadik and Orion 32-bit down-counting clocksources
to generic mmio clocksource infrastructure.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
mv78xx0 and kirkwood use identical mpp code.
It should also be possible to rewrite the orion5x mpp to use this
platform code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This change removes the interrupt resource. The driver does not use
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
The core interrupt chip is a straight forward conversion. The gpio
chip is implemented with two instances of the irq_chip_type which can
be switched with the irq_set_type function. That allows us to use the
generic callbacks and avoids the conditionals in them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Use irq_set_chip_and_handler() instead. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Convert to the new function names. Automated with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use the proper wrappers and use the flow type in irq_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch makes the various mach dirs that use the plat-orion GPIO
code pass in GPIO-related platform info (GPIO controller base address,
secondary base IRQ number, etc) explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Convert orion platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 21f0ba90a447 "orion/kirkwood: reset PCIe unit on boot" made the
reset of the PCIe unit unconditional. While this may fix problems on some
targets, this also causes problems on other targets.
Saeed Bishara <saeed@marvell.com> said about the original problem: "We
couln't pinpoint the root cause of this issue, actually we failed to
reproduce that issue."
So let's restrict the reset of the PCIe unit only to the target where
the original problem was observed.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
|
|
Patch found in QNAPs vendor source package, with some cleanups
(proper defines, shortened max. timeout from 1s to 200ms).
Without this patch the PCIe SATA controller (Marvell 88sx7042/sata_mv)
in my QNAP TS-419P (Marvell 88f6281/Kirkwood) stops working after a
few minutes.
The symptomes are described in this thread:
http://marc.info/?l=linux-ide&m=124822863706181&w=2
[ Note: this is a workaround in need of a better analysis/solution -- NP ]
Acked-by: Saeed Bishara <saeed@marvell.com>
Tested-by: Bernhard R. Link <brl@pcpool00.mathematik.uni-freiburg.de>
Seconded-by: Martin Michlmayr <tbm@cyrius.com>
I'm_not_very_happy_with_it-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This patch add audio related definitions and functions
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add support for a board to register a callback to get the state of the
RnB line if it has it attached.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
power of two
The PCIe inbound window size is supposed to be a power of two. If
the total amount of RAM installed in the system is not a power of two,
round it up such that it is.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Include linux/init.h for __init to fix this error:
CC [M] drivers/net/wireless/wl12xx/boot.o
In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13,
from arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/net/wireless/wl12xx/boot.c:24:
arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’
make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1
make[5]: *** [drivers/net/wireless/wl12xx] Error 2
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Erik Benada <erikbenada@yahoo.ca>
[ nico: fix locking, additional cleanups ]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
With a TCLK = 200MHz, the half period of the hardware timer is roughly
10 seconds. Because cnt32_to_63() must be called at least once per
half period of the base hardware counter, it is a bit risky to rely
solely on scheduling to generate frequent enough calls. Let's use a
kernel timer to ensure this.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
sched_clock implementation for orion platform. Its realized using
free-running clocksource timer, which provides a resolution of 7.5ns
(depending on tclk). It's derived from PXA's sched_clock implementation.
[ nico: renamed orion2ns to tclk2ns, fixed max value in the comment ]
Signed-off-by: Stefan Agner <stefan.agner@yahoo.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5460/1: Orion: reduce namespace pollution
[ARM] 5458/1: pcmcia: pxa2xx-sharpsl: check if we do have Scoop config
[ARM] 5457/1: mach-imx gpio buildfix
[ARM] 5456/1: add sys_preadv and sys_pwritev
[ARM] pxa/pcm990: start external GPIOs immediately after built-in ones
[ARM] pxa/palm27x: General fix for Palm27x aSoC driver
[ARM] pxa/mioa701: use GPIO95 as AC97 reset line
[ARM] pxa: merge AC97 platform data structures
[ARM] pxa/magician: remove un-necessary #include of pxa-regs.h and hardware.h
|
|
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
sound/soc/pxa/pxa2xx-i2s.c
|
|
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Especially on Kirkwood, a couple GPIOs are actually only output capable.
Let's separate the ability to configure a GPIO as input or output to
accommodate this restriction.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The GPIO interrupts can be configured as either level triggered or edge
triggered, with a default of level triggered. When an edge triggered
interrupt is requested, the gpio_irq_set_type method is called which
currently switches the given IRQ descriptor between two struct irq_chip
instances: orion_gpio_irq_level_chip and orion_gpio_irq_edge_chip. This
happens via __setup_irq() which also calls irq_chip_set_defaults() to
assign default methods to uninitialized ones. The problem is that
irq_chip_set_defaults() is called before the irq_chip reference is
switched, leaving the new irq_chip (orion_gpio_irq_edge_chip in this
case) with uninitialized methods such as chip->startup() causing a kernel
oops.
Many solutions are possible, such as making irq_chip_set_defaults() global
and calling it from gpio_irq_set_type(), or calling __irq_set_trigger()
before irq_chip_set_defaults() in __setup_irq(). But those require
modifications to the generic IRQ code which might have adverse effect on
other architectures, and that would still be a fragile arrangement.
Manually copying the missing methods from within gpio_irq_set_type()
would be really ugly and it would break again the day new methods with
automatic defaults are added.
A better solution is to have a single irq_chip instance which can deal
with both edge and level triggered interrupts. It is also a good idea
to switch the IRQ handler instead, as the edge IRQ handler allows for
one edge IRQ event to be queued as the IRQ is actually masked only when
that second IRQ is received, at which point the hardware can queue an
additional IRQ event, making edge triggered interrupts a bit more
reliable.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
|
|
Split off Orion GPIO IRQ handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Split off Orion GPIO handling code into plat-orion/, and add
support for multiple sets of (32) GPIO pins.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
|
|
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
|
