summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2020-05-08ARM: dts: colibri-imx6ull: Use pull-down for adc pinsPhilippe Schenker
As suggested by the reference manual in a note in chapter 13.2 this commit disables the keeper and enables a 100k pull-down on the adc pins. Related-to: ELB-2690 Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> (cherry picked from commit d5a3675860d03d783689de3ed7cb3dec27e6a155)
2020-04-15ARM: dts: imx6ull-colibri: fix vqmmc regulatorMax Krummenacher
The correct spelling for the property is gpios, otherwise the regulator will neither reserve nor control any gpio(s). Thus any SD/MMC card which can use UHS 1 modes will fail. Related-to: #46566 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2020-04-15ARM: dts (ds): imx6ull-colibri: Use wifi from mainlinePhilippe Schenker
This takes the mainline part that adds the wifi chip. This patch solves the issue that exists when resuming from suspend. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2020-04-15colibri-imx6ull: add fsl,tuning-start-tap propertyIgor Opaniuk
Specify the start dealy cell point when send first CMD19 in tuning procedure. This fixes these tunning procedure issues, and lets to use UHS-I mode properly: sdhci: Tuning procedure failed, falling back to fixed sampling clock mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00 Fixes: http://redmine.toradex.int/issues/46566 Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-04-15ARM: dts: Add stmpe-adc DT node to Toradex iMX6 modulesPhilippe Schenker
Add the stmpe-adc DT node as found on Toradex iMX6 modules Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2020-04-15ARM: dts: add recovery for I2C for iMX7Oleksandr Suvorov
- add recovery mode for applicable i2c buses for Colibri iMX7 module. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-04-15ARM: dts: add recovery mode for all I2C busesOleksandr Suvorov
- fix the name of pinctrl set for i2c2 recovery mode; - add recovery mode for applicable i2c buses for Apalis/Colibri iMX6Q/D/DL modules. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Related to: #49059
2020-04-15ARM: dts: imx6q: correct SDMA script type for spi5Oleksandr Suvorov
Commit 41ec065fc5841 fixes ecspi sdma script type for spi1-4 only. Commit df07101e1c4a2 sets wrong type of sdma script for SPI5. The workaroud sdma script NOT work in SPBA bus, so return back the correct sdma script type for spi5. Related to: #48675 Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-03-28Merge remote-tracking branch 'remotes/fslc/4.9-2.3.x-imx' into ↵Colibri-iMX7_LXDE-Image_2.8b6.184-20190401Colibri-iMX6_LXDE-Image_2.8b6.184-20190401Colibri-iMX6ULL_LXDE-Image_2.8b6.184-20190401Apalis-iMX6_LXDE-Image_2.8b6.184-20190401Marcel Ziswiler
toradex_4.9-2.3.x-imx-next
2019-03-28Merge tag 'v4.9.166' into 4.9-2.3.x-imxMarcel Ziswiler
This is the 4.9.166 stable release
2019-03-28ARM: dts: colibri_imx6: fix mcp2515 labelsMarcel Ziswiler
I don't know where that mcp258x came from but it really is a mcp2515. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-03-23ARM: s3c24xx: Fix boolean expressions in osiris_dvs_notifyGustavo A. R. Silva
commit e2477233145f2156434afb799583bccd878f3e9f upstream. Fix boolean expressions by using logical AND operator '&&' instead of bitwise operator '&'. This issue was detected with the help of Coccinelle. Fixes: 4fa084af28ca ("ARM: OSIRIS: DVS (Dynamic Voltage Scaling) supoort.") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> [krzk: Fix -Wparentheses warning] Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-23ARM: 8824/1: fix a migrating irq bug when hotplug cpuDietmar Eggemann
[ Upstream commit 1b5ba350784242eb1f899bcffd95d2c7cff61e84 ] Arm TC2 fails cpu hotplug stress test. This issue was tracked down to a missing copy of the new affinity cpumask for the vexpress-spc interrupt into struct irq_common_data.affinity when the interrupt is migrated in migrate_one_irq(). Fix it by replacing the arm specific hotplug cpu migration with the generic irq code. This is the counterpart implementation to commit 217d453d473c ("arm64: fix a migrating irq bug when hotplug cpu"). Tested with cpu hotplug stress test on Arm TC2 (multi_v7_defconfig plus CONFIG_ARM_BIG_LITTLE_CPUFREQ=y and CONFIG_ARM_VEXPRESS_SPC_CPUFREQ=y). The vexpress-spc interrupt (irq=22) on this board is affine to CPU0. Its affinity cpumask now changes correctly e.g. from 0 to 1-4 when CPU0 is hotplugged out. Suggested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-23ARM: OMAP2+: Variable "reg" in function omap4_dsi_mux_pads() could be ↵Yizhuo
uninitialized [ Upstream commit dc30e70391376ba3987aeb856ae6d9c0706534f1 ] In function omap4_dsi_mux_pads(), local variable "reg" could be uninitialized if function regmap_read() returns -EINVAL. However, it will be used directly in the later context, which is potentially unsafe. Signed-off-by: Yizhuo <yzhai003@ucr.edu> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-20imx6qdl-colibri.dtsi: UHS-I support for v1.1a hwIgor Opaniuk
Provide proper configuration for VGEN3, to make sure it's is always powered which allows that rail to be automatically switched to 1.8 volts for proper UHS-I operation. By default it's disabled. With UHS-I enabled: [ 104.153898] mmc1: new ultra high speed SDR104 SDHC card at address 59b4 [ 104.166202] mmcblk1: mmc1:59b4 USD00 15.0 GiB [ 104.173923] mmcblk1: p1 root@colibri-imx6:~# hdparm -t /dev/mmcblk1 /dev/mmcblk1: Timing buffered disk reads: 226 MB in 3.01 seconds = 75.01 MB/sec Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-03-13ARM: dts: exynos: Do not ignore real-world fuse values for thermal zone 0 on ↵Krzysztof Kozlowski
Exynos5420 commit 28928a3ce142b2e4e5a7a0f067cefb41a3d2c3f9 upstream. In Odroid XU3 Lite board, the temperature levels reported for thermal zone 0 were weird. In warm room: /sys/class/thermal/thermal_zone0/temp:32000 /sys/class/thermal/thermal_zone1/temp:51000 /sys/class/thermal/thermal_zone2/temp:55000 /sys/class/thermal/thermal_zone3/temp:54000 /sys/class/thermal/thermal_zone4/temp:51000 Sometimes after booting the value was even equal to ambient temperature which is highly unlikely to be a real temperature of sensor in SoC. The thermal sensor's calibration (trimming) is based on fused values. In case of the board above, the fused values are: 35, 52, 43, 58 and 43 (corresponding to each TMU device). However driver defined a minimum value for fused data as 40 and for smaller values it was using a hard-coded 55 instead. This lead to mapping data from sensor to wrong temperatures for thermal zone 0. Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10) do not impose any limits on fused values. Since we do not have any knowledge about these limits, use 0 as a minimum accepted fused value. This should essentially allow accepting any reasonable fused value thus behaving like vendor driver. The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing exynos4412 with one change - the samsung,tmu_min_efuse_value. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Eduardo Valentin <edubezval@gmail.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Anand Moon <linux.amoon@gmail.com> Tested-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-13ARM: 8781/1: Fix Thumb-2 syscall return for binutils 2.29+Vincent Whitchurch
[ Upstream commit afc9f65e01cd114cb2cedf544d22239116ce0cc6 ] When building the kernel as Thumb-2 with binutils 2.29 or newer, if the assembler has seen the .type directive (via ENDPROC()) for a symbol, it automatically handles the setting of the lowest bit when the symbol is used with ADR. The badr macro on the other hand handles this lowest bit manually. This leads to a jump to a wrong address in the wrong state in the syscall return path: Internal error: Oops - undefined instruction: 0 [#2] SMP THUMB2 Modules linked in: CPU: 0 PID: 652 Comm: modprobe Tainted: G D 4.18.0-rc3+ #8 PC is at ret_fast_syscall+0x4/0x62 LR is at sys_brk+0x109/0x128 pc : [<80101004>] lr : [<801c8a35>] psr: 60000013 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 50c5387d Table: 9e82006a DAC: 00000051 Process modprobe (pid: 652, stack limit = 0x(ptrval)) 80101000 <ret_fast_syscall>: 80101000: b672 cpsid i 80101002: f8d9 2008 ldr.w r2, [r9, #8] 80101006: f1b2 4ffe cmp.w r2, #2130706432 ; 0x7f000000 80101184 <local_restart>: 80101184: f8d9 a000 ldr.w sl, [r9] 80101188: e92d 0030 stmdb sp!, {r4, r5} 8010118c: f01a 0ff0 tst.w sl, #240 ; 0xf0 80101190: d117 bne.n 801011c2 <__sys_trace> 80101192: 46ba mov sl, r7 80101194: f5ba 7fc8 cmp.w sl, #400 ; 0x190 80101198: bf28 it cs 8010119a: f04f 0a00 movcs.w sl, #0 8010119e: f3af 8014 nop.w {20} 801011a2: f2af 1ea2 subw lr, pc, #418 ; 0x1a2 To fix this, add a new symbol name which doesn't have ENDPROC used on it and use that with badr. We can't remove the badr usage since that would would cause breakage with older binutils. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-13ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMUMarek Szyprowski
commit a66352e005488ecb4b534ba1af58a9f671eba9b8 upstream. Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250 PMU node. This fixes the following warning on boot: exynos_clkout_init: failed to register clkout clock Fixes: d19bb397e19e ("ARM: dts: exynos: Update PMU node with CLKOUT related data") Cc: <stable@vger.kernel.org> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-13ARM: dts: exynos: Fix pinctrl definition for eMMC RTSN line on Odroid X2/U3Marek Szyprowski
commit ec33745bccc8f336957c751f4153421cc9ef5a54 upstream. Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common") added MMC power sequence for eMMC card of Odroid X2/U3. It reused generic sd1_cd pin control configuration node and only disabled pull-up. However that time the pinctrl configuration was not applied during MMC power sequence driver initialization. This has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to proper platform device"). It turned out then, that the provided pinctrl configuration is not correct, because the eMMC_RTSN line is being re-configured as 'special function/card detect function for mmc1 controller' not the simple 'output', thus the power sequence driver doesn't really set the pin value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this by providing separate node with eMMC_RTSN pin configuration. Cc: <stable@vger.kernel.org> Reported-by: Markus Reichl <m.reichl@fivetechno.de> Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-13ARM: pxa: ssp: unneeded to free devm_ allocated dataPeng Hao
[ Upstream commit ba16adeb346387eb2d1ada69003588be96f098fa ] devm_ allocated data will be automatically freed. The free of devm_ allocated data is invalid. Fixes: 1c459de1e645 ("ARM: pxa: ssp: use devm_ functions") Signed-off-by: Peng Hao <peng.hao2@zte.com.cn> [title's prefix changed] Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-12ARM: dts: Add sleep state to the sd-card pinsPhilippe Schenker
This commit adds a sleep state to the ixora devicetree. This prevents backfeeding when sending the module to any sleep state. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2019-03-12ARM: dts: Add Apalis iMX6 Ixora v1.2Philippe Schenker
Copied v1.1 devicetree and adopted it for v1.2 of the Ixora board. Added the devicetree in the Makefile Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2019-03-11ARM: dts: imx6: Add sleep state to can interfacesPhilippe Schenker
This patch prepares the devicetree for the new Ixora V1.2 where we are able to turn off the supply of the can transceiver. This implies to use a sleep state on transmission pins in order to prevent backfeeding. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2019-02-20gpio: pl061: handle failed allocationsNicholas Mc Guire
[ Upstream commit df209c43a0e8258e096fb722dfbdae4f0dd13fde ] devm_kzalloc(), devm_kstrdup() and devm_kasprintf() all can fail internal allocation and return NULL. Using any of the assigned objects without checking is not safe. As this is early in the boot phase and these allocations really should not fail, any failure here is probably an indication of a more serious issue so it makes little sense to try and rollback the previous allocated resources or try to continue; but rather the probe function is simply exited with -ENOMEM. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 684284b64aae ("ARM: integrator: add MMCI device to IM-PD1") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: dts: kirkwood: Fix polarity of GPIO fan linesLinus Walleij
[ Upstream commit b5f034845e70916fd33e172fad5ad530a29c10ab ] These two lines are active high, not active low. The bug was found when we changed the kernel to respect the polarity defined in the device tree. Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan") Cc: Jamie Lentin <jm@lentin.co.uk> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Julien D'Ascenzio <jdascenzio@posteo.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Jamie Lentin <jm@lentin.co.uk> Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net> Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: dts: da850-lcdk: Correct the sound card namePeter Ujfalusi
[ Upstream commit c25748acc5c20786ecb7518bfeae8fcef93472d6 ] To avoid the following error: asoc-simple-card sound: ASoC: Failed to create card debugfs directory Which is because the card name contains '/' character, which can not be used in file or directory names. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: dts: da850-evm: Correct the sound card namePeter Ujfalusi
[ Upstream commit 7fca69d4e43fa1ae9cb4f652772c132dc5a659c6 ] To avoid the following error: asoc-simple-card sound: ASoC: Failed to create card debugfs directory Which is because the card name contains '/' character, which can not be used in file or directory names. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: fix the cockup in the previous patchRussell King
Commit d6951f582cc50ba0ad22ef46b599740966599b14 upstream. The intention in the previous patch was to only place the processor tables in the .rodata section if big.Little was being built and we wanted the branch target hardening, but instead (due to the way it was tested) it ended up always placing the tables into the .rodata section. Although harmless, let's correct this anyway. Fixes: 3a4d0c2172bc ("ARM: ensure that processor vtables is not lost after boot") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: ensure that processor vtables is not lost after bootRussell King
Commit 3a4d0c2172bcf15b7a3d9d498b2b355f9864286b upstream. Marek Szyprowski reported problems with CPU hotplug in current kernels. This was tracked down to the processor vtables being located in an init section, and therefore discarded after kernel boot, despite being required after boot to properly initialise the non-boot CPUs. Arrange for these tables to end up in .rodata when required. Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Fixes: 383fb3ee8024 ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: spectre-v2: per-CPU vtables to work around big.Little systemsRussell King
Commit 383fb3ee8024d596f488d2dbaf45e572897acbdb upstream. In big.Little systems, some CPUs require the Spectre workarounds in paths such as the context switch, but other CPUs do not. In order to handle these differences, we need per-CPU vtables. We are unable to use the kernel's per-CPU variables to support this as per-CPU is not initialised at times when we need access to the vtables, so we have to use an array indexed by logical CPU number. We use an array-of-pointers to avoid having function pointers in the kernel's read/write .data section. Note: Added include of linux/slab.h in arch/arm/smp.c. Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: add PROC_VTABLE and PROC_TABLE macrosRussell King
Commit e209950fdd065d2cc46e6338e47e52841b830cba upstream. Allow the way we access members of the processor vtable to be changed at compile time. We will need to move to per-CPU vtables to fix the Spectre variant 2 issues on big.Little systems. However, we have a couple of calls that do not need the vtable treatment, and indeed cause a kernel warning due to the (later) use of smp_processor_id(), so also introduce the PROC_TABLE macro for these which always use CPU 0's function pointers. Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: clean up per-processor check_bugs method callRussell King
Commit 945aceb1db8885d3a35790cf2e810f681db52756 upstream. Call the per-processor type check_bugs() method in the same way as we do other per-processor functions - move the "processor." detail into proc-fns.h. Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: split out processor lookupRussell King
Commit 65987a8553061515b5851b472081aedb9837a391 upstream. Split out the lookup of the processor type and associated error handling from the rest of setup_processor() - we will need to use this in the secondary CPU bringup path for big.Little Spectre variant 2 mitigation. Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: make lookup_processor_type() non-__initRussell King
Commit 899a42f836678a595f7d2bc36a5a0c2b03d08cbc upstream. Move lookup_processor_type() out of the __init section so it is callable from (eg) the secondary startup code during hotplug. Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8810/1: vfp: Fix wrong assignement to ufp_excJulien Thierry
Commit 5df7a99bdd0de4a0480320264c44c04543c29d5a upstream. In vfp_preserve_user_clear_hwstate, ufp_exc->fpinst2 gets assigned to itself. It should actually be hwstate->fpinst2 that gets assigned to the ufp_exc field. Fixes commit 3aa2df6ec2ca6bc143a65351cca4266d03a8bc41 ("ARM: 8791/1: vfp: use __copy_to_user() when saving VFP state"). Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8797/1: spectre-v1.1: harden __copy_to_userJulien Thierry
Commit a1d09e074250fad24f1b993f327b18cc6812eb7a upstream. Sanitize user pointer given to __copy_to_user, both for standard version and memcopy version of the user accessor. Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8796/1: spectre-v1,v1.1: provide helpers for address sanitizationJulien Thierry
Commit afaf6838f4bc896a711180b702b388b8cfa638fc upstream. Introduce C and asm helpers to sanitize user address, taking the address range they target into account. Use asm helper for existing sanitization in __copy_from_user(). Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8795/1: spectre-v1.1: use put_user() for __put_user()Julien Thierry
Commit e3aa6243434fd9a82e84bb79ab1abd14f2d9a5a7 upstream. When Spectre mitigation is required, __put_user() needs to include check_uaccess. This is already the case for put_user(), so just make __put_user() an alias of put_user(). Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8794/1: uaccess: Prevent speculative use of the current addr_limitJulien Thierry
Commit 621afc677465db231662ed126ae1f355bf8eac47 upstream. A mispredicted conditional call to set_fs could result in the wrong addr_limit being forwarded under speculation to a subsequent access_ok check, potentially forming part of a spectre-v1 attack using uaccess routines. This patch prevents this forwarding from taking place, but putting heavy barriers in set_fs after writing the addr_limit. Porting commit c2f0ad4fc089cff8 ("arm64: uaccess: Prevent speculative use of the current addr_limit"). Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8793/1: signal: replace __put_user_error with __put_userJulien Thierry
Commit 18ea66bd6e7a95bdc598223d72757190916af28b upstream. With Spectre-v1.1 mitigations, __put_user_error is pointless. In an attempt to remove it, replace its references in frame setups with __put_user. Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8792/1: oabi-compat: copy oabi events using __copy_to_user()Julien Thierry
Commit 319508902600c2688e057750148487996396e9ca upstream. Copy events to user using __copy_to_user() rather than copy members of individually with __put_user_error(). This has the benefit of disabling/enabling PAN once per event intead of once per event member. Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8791/1: vfp: use __copy_to_user() when saving VFP stateJulien Thierry
Commit 3aa2df6ec2ca6bc143a65351cca4266d03a8bc41 upstream. Use __copy_to_user() rather than __put_user_error() for individual members when saving VFP state. This has the benefit of disabling/enabling PAN once per copied struct intead of once per write. Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ARM: 8789/1: signal: copy registers using __copy_to_user()Julien Thierry
Commit 5ca451cf6ed04443774bbb7ee45332dafa42e99f upstream. When saving the ARM integer registers, use __copy_to_user() to copy them into user signal frame, rather than __put_user_error(). This has the benefit of disabling/enabling PAN once for the whole copy intead of once per write. Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-19ARM: dts: imx6qdl-colibri: add phy to fecPhilippe Schenker
If someone wants to add settings to the phy it is necessary to actually add the phy. This commit includes micrel,led-mode that is set to the default value, prepared for someone who wants to change this. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2019-02-15ARM: tango: Improve ARCH_MULTIPLATFORM compatibilityMarc Gonzalez
commit d0f9f16788e15d9eb40f68b047732d49658c5a3a upstream. Calling platform-specific code unconditionally blows up when running an ARCH_MULTIPLATFORM kernel on a different platform. Don't do it. Reported-by: Paolo Pisati <p.pisati@gmail.com> Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: stable@vger.kernel.org # v4.8+ Fixes: a30eceb7a59d ("ARM: tango: add Suspend-to-RAM support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15ARM: iop32x/n2100: fix PCI IRQ mappingRussell King
commit db4090920ba2d61a5827a23e441447926a02ffee upstream. Booting 4.20 on a TheCUS N2100 results in a kernel oops while probing PCI, due to n2100_pci_map_irq() having been discarded during boot. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Cc: stable@vger.kernel.org # 2.6.18+ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12arm64: KVM: Skip MMIO insn after emulationMark Rutland
[ Upstream commit 0d640732dbebed0f10f18526de21652931f0b2f2 ] When we emulate an MMIO instruction, we advance the CPU state within decode_hsr(), before emulating the instruction effects. Having this logic in decode_hsr() is opaque, and advancing the state before emulation is problematic. It gets in the way of applying consistent single-step logic, and it prevents us from being able to fail an MMIO instruction with a synchronous exception. Clean this up by only advancing the CPU state *after* the effects of the instruction are emulated. Cc: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12ARM: pxa: avoid section mismatch warningArnd Bergmann
[ Upstream commit 88af3209aa0881aa5ffd99664b6080a4be5f24e5 ] WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info() The function littleton_init_lcd() references the function __init pxa_set_fb_info(). This is often because littleton_init_lcd lacks a __init annotation or the annotation of pxa_set_fb_info is wrong. WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info() The function zeus_register_ohci() references the function __init pxa_set_ohci_info(). This is often because zeus_register_ohci lacks a __init annotation or the annotation of pxa_set_ohci_info is wrong. WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info() The function cm_x300_init_u2d() references the function __init pxa3xx_set_u2d_info(). This is often because cm_x300_init_u2d lacks a __init annotation or the annotation of pxa3xx_set_u2d_info is wrong. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12ARM: dts: Fix OMAP4430 SDP Ethernet startupRussell King - ARM Linux
[ Upstream commit 84fb6c7feb1494ebb7d1ec8b95cfb7ada0264465 ] It was noticed that unbinding and rebinding the KSZ8851 ethernet resulted in the driver reporting "failed to read device ID" at probe. Probing the reset line with a 'scope while repeatedly attempting to bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is constantly held at zero, meaning the device is held in reset, and does not respond on the SPI bus. Experimentation with the startup delay on the regulator set to 50ms shows that the reset is positively released after 20ms. Schematics for this board are not available, and the traces are buried in the inner layers of the board which makes tracing where the RSTN pin extremely difficult. We can only guess that the RSTN pin is wired to a reset generator chip driven off the ethernet supply, which fits the observed behaviour. Include this delay in the regulator startup delay - effectively treating the reset as a "supply stable" indicator. This can not be modelled as a delay in the KSZ8851 driver since the reset generation is board specific - if the RSTN pin had been wired to a GPIO, reset could be released earlier via the already provided support in the KSZ8851 driver. This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based on Blaze schematics that should be very close to SDP4430: TPS22902YFPR is used as the regulator switch (gpio48 controlled): Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV. (SCH Note: Threshold set at 90%. Vsense: 0.405V). According to the TPS3808 data sheet the RESET delay time when Ct is open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> [tony@atomide.com: updated with notes from schematics from Peter] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12ARM: dts: mmp2: fix TWSI2Lubomir Rintel
[ Upstream commit 1147e05ac9fc2ef86a3691e7ca5c2db7602d81dd ] Marvell keeps their MMP2 datasheet secret, but there are good clues that TWSI2 is not on 0xd4025000 on that platform, not does it use IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor: arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58 I'm taking a somewhat educated guess that is probably a copy & paste error from PXA168 or PXA910 and that the real controller in fact hides at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17. I'm also copying some properties from TWSI1 that were missing or incorrect. Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-04 11:00:51 +0000