| Age | Commit message (Collapse) | Author |
|---|
|
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Cc: "Nelson, Shannon" <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch is fixes the sequoia.dts device tree file to use the values defined
in the 440Epx data sheet from AMCC.
That fixes an issue where some devices, including graphics cards, would not
initialize properly because the PCI resource space was not big enough.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs
All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0. Changing pixel clock has no effect
on other fbs.
Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0
required command line parameters to preallocate memory for frame buffer diufb.
optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:
Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60
Bpp
bpp=32, bpp=24, or bpp=16
Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS
Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.
If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds default NOR entries to the AMCC Canyonlands (460EX)
and Glacier (460GT) dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
MPC8568E has 64K byte MURAM, so the size should be 0x10000, not 0xc000.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts. The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
- get rid of `model = "UCC"' in the ucc nodes
It isn't used anywhere, so remove it. If we'll ever need something
like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
Drivers are modified for backward compatibility's sake.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch modifies the Embedded Planet EP8248E device tree to reference the
SMC paramater RAM base register instead of the parameter RAM allocated by the
boot loader.
The cpm_uart driver will allocate parameter RAM itself, making the serial port
initialisation independent of the boot loader.
The patch adds the parameter RAM allocated by the boot loader in the CPM muram
node, making it available to the kernel.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform. Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank. This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports. The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device. The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove several unused (or software config only) properties.
Rename marvel node to "system-controller". Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated. This fixes them. Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:
- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
(the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This gets the FEC ethernet driver working again on the lite5200
platform.
The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200. Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
DTS updates that fix booting problems on mpc5200-based boards:
- change to ethernet reg property
- addition of mdio and phy nodes
- removal of pci node (Motion-Pro board)
Other DTS updates:
- update i2c device tree nodes
- add lpb bus node and flash device (without partitions defined)
- add rtc i2c nodes
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
|
|
as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
This patch fixes USB malfunctioning on the MPC837xE-RDB boards.
Similar patch has been already applied for the MDS boards:
commit 28b958859206b7010d03129611c2e444898e3ee4
Author: Li Yang <leoli@freescale.com>
Date: Thu Mar 6 18:42:26 2008 +0800
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add device tree file for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch adds the L2 cache node to the Taishan 440GX dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This adds a DTS file for the AMCC 440EP Yosemite board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This dts source file for the AMCC 460EX Canyonlands evalutaion board
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.
The now obsolete linux,network-index properties are removed from the
corresponding device trees. This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.
The references to linux,network-index are removed from
booting-without-of.txt. Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree. By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip. Otherwise the driver won't find the device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The following patch allows interrupts to occur on the
sbc8548. Currently PCI and PCI-X devices get assigned an IRQ
but the interrupt count never increases. This solves the
problem and adds PCI support as well.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch changes the katmai (440SPe) L1 cache size to 32k. Some
whitespace issues are cleaned up too.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Since the 4xx PCIe driver checks for 405ex compatibility, the
PCIe interface was not detected as it is currently defined as
"405exr" compatible. This patch changes it to "405ex".
The 405EX and 405EXr are identical exept that the 2nd PCIe and the
2nd EMAC interfaces are missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Remove all "i2c" and "xxmii-interface" (rgmii etc) device_type entries
from the 4xx dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
