| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
"Here are five fixes for you to pull please.
They're all CC'ed to stable except the "Fix PE state format" one which
went in this release"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: 32 bit getcpu VDSO function uses 64 bit instructions
powerpc/powernv: Replace OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE
powerpc/eeh: Fix PE state format
powerpc/pseries: Fix endiannes issue in RTAS call from xmon
powerpc/powernv: Fix the hmi event version check.
|
|
I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.
Fixes: 18ad51dd342a ("powerpc: Add VDSO version of getcpu")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Obviously I had wrong format given to the PE state output from
/sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which
was introduced by commit 2013add4ce73. The patch fixes it up.
Fixes: 2013add4ce73 ("powerpc/eeh: Show hex prefix for PE state sysfs")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This is now fully replaced with the generic "no_64bit_msi" one
that is set by the respective drivers directly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Back in 7230c5644188 ("powerpc: Rework lazy-interrupt handling") we
added a call out to restore_interrupts() (written in c) before calling
do_notify_resume:
bl restore_interrupts
addi r3,r1,STACK_FRAME_OVERHEAD
bl do_notify_resume
Unfortunately do_notify_resume takes two arguments, the second one
being the thread_info flags:
void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)
We do populate r4 (the second argument) earlier, but
restore_interrupts() is free to muck it up all it wants. My guess is
the gcc compiler gods shone down on us and its register allocator
never used r4. Sometimes, rarely, luck is on our side.
LLVM on the other hand did trample r4.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Firmware-assisted dump (fadump) kernel code is not endian safe. The
below patch fixes this issue. Tested this patch with upstream kernel.
Below output shows crash tool successfully opening LE fadump vmcore.
# crash vmlinux vmcore
GNU gdb (GDB) 7.6
This GDB was configured as "powerpc64le-unknown-linux-gnu"...
KERNEL: vmlinux
DUMPFILE: vmcore
CPUS: 16
DATE: Wed Dec 31 19:00:00 1969
UPTIME: 00:03:28
LOAD AVERAGE: 0.46, 0.86, 0.41
TASKS: 268
NODENAME: linux-dhr2
RELEASE: 3.17.0-rc5-7-default
VERSION: #6 SMP Tue Sep 30 01:06:34 EDT 2014
MACHINE: ppc64le (4116 Mhz)
MEMORY: 40 GB
PANIC: "Oops: Kernel access of bad area, sig: 11 [#1]" (check log for details)
PID: 6223
COMMAND: "bash"
TASK: c0000009661b2500 [THREAD_INFO: c000000967ac0000]
CPU: 2
STATE: TASK_RUNNING (PANIC)
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Make the comment in pSeries_lpar_hptab_clear() clearer]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull more powerpc updates from Michael Ellerman:
"Here's some more updates for powerpc for 3.18.
They are a bit late I know, though must are actually bug fixes. In my
defence I nearly cut the top of my finger off last weekend in a
gruesome bike maintenance accident, so I spent a good part of the week
waiting around for doctors. True story, I can send photos if you like :)
Probably the most interesting fix is the sys_call_table one, which
enables syscall tracing for powerpc. There's a fix for HMI handling
for old firmware, more endian fixes for firmware interfaces, more EEH
fixes, Anton fixed our routine that gets the current stack pointer,
and a few other misc bits"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (22 commits)
powerpc: Only do dynamic DMA zone limits on platforms that need it
powerpc: sync pseries_le_defconfig with pseries_defconfig
powerpc: Add printk levels to setup_system output
powerpc/vphn: NUMA node code expects big-endian
powerpc/msi: Use WARN_ON() in msi bitmap selftests
powerpc/msi: Fix the msi bitmap alignment tests
powerpc/eeh: Block CFG upon frozen Shiner adapter
powerpc/eeh: Don't collect logs on PE with blocked config space
powerpc/eeh: Block PCI config access upon frozen PE
powerpc/pseries: Drop config requests in EEH accessors
powerpc/powernv: Drop config requests in EEH accessors
powerpc/eeh: Rename flag EEH_PE_RESET to EEH_PE_CFG_BLOCKED
powerpc/eeh: Fix condition for isolated state
powerpc/pseries: Make CPU hotplug path endian safe
powerpc/pseries: Use dump_stack instead of show_stack
powerpc: Rename __get_SP() to current_stack_pointer()
powerpc: Reimplement __get_SP() as a function not a define
powerpc/numa: Add ability to disable and debug topology updates
powerpc/numa: check error return from proc_create
powerpc/powernv: Fallback to old HMI handling behavior for old firmware
...
|
|
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
|
|
Scott's patch 1c98025c6c95 "Dynamic DMA zone limits" changed
dma_direct_alloc_coherent() to start using dev->coherent_dma_mask.
That seems fair enough, but it exposes the fact that some of the drivers
we care about on IBM platforms aren't setting the coherent mask.
The proper fix is to have drivers set the coherent mask and also have
the platform code honor it.
For now, just restrict the dynamic DMA zone limits to the platforms that
need it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
|
|
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 0b0b0893d49b "of/pci: Fix the conversion of IO ranges into IO
resources" changed the behaviour of of_pci_range_to_resource().
Previously it simply populated the resource based on the arguments. Now
it calls pci_register_io_range() and pci_address_to_pio(). These both
have two implementations depending on whether PCI_IOBASE is defined,
which it is not for powerpc.
Further complicating matters, both routines are weak, and powerpc
implements it's own version of one - pci_address_to_pio(). However
powerpc's implementation depends on other initialisations which are done
later in boot.
The end result is incorrectly initialised IO space. Often we can get
away with that, because we don't make much use of IO space. However
virtio requires it, so we see eg:
pci_bus 0000:00: root bus resource [io 0xffff] (bus address [0xffffffffffffffff-0xffffffffffffffff])
PCI: Cannot allocate resource region 0 of device 0000:00:01.0, will remap
virtio-pci 0000:00:01.0: can't enable device: BAR 0 [io size 0x0020] not assigned
The simplest fix for now is to just stop using of_pci_range_to_resource(),
and open-code the original implementation, that's all we want it to do.
Fixes: 0b0b0893d49b ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When the PE's config space is marked as blocked, PCI config read
requests always return 0xFF's. It's pointless to collect logs in
this case.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The problem was found when I tried to inject PCI config error by
PHB3 PAPR error injection registers into Broadcom Austin 4-ports
NIC adapter. The frozen PE was reported successfully and EEH core
started to recover it. However, I run into fenced PHB when dumping
PCI config space as EEH logs. I was told that PCI config requests
should not be progagated to the adapter until PE reset is done
successfully. Otherise, we would run out of PHB internal credits
and trigger PCT (PCIE Completion Timeout), which leads to the
fenced PHB.
The patch introduces another PE flag EEH_PE_CFG_RESTRICTED, which
is set during PE initialization time if the PE includes the specific
PCI devices that need block PCI config access until PE reset is done.
When the PE becomes frozen for the first time, EEH_PE_CFG_BLOCKED is
set if the PE has flag EEH_PE_CFG_RESTRICTED. Then the PCI config
access to the PE will be dropped by platform PCI accessors until
PE reset is done successfully. The mechanism is shared by PowerNV
platform owned PE or userland owned ones. It's not used on pSeries
platform yet.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pSeires EEH config accessors rely on rtas_{read, write}_config()
and the condition to check if the PE's config space is blocked
should be moved to those 2 functions so that config requests from
kernel, userland, EEH core can be dropped to avoid recursive EEH error
if necessary.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The flag EEH_PE_RESET indicates blocking config space of the PE
during reset time. We potentially need block PE's config space
other than reset time. So it's reasonable to replace it with
EEH_PE_CFG_BLOCKED to indicate its usage.
There are no substantial code or logic changes in this patch.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Function eeh_pe_state_mark() could possibly have combination of
multiple EEH PE state as its argument. The patch fixes the condition
used to check if EEH_PE_ISOLATED is included.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Michael points out that __get_SP() is a pretty horrible
function name. Let's give it a better name.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Li Zhong points out an issue with our current __get_SP()
implementation. If ftrace function tracing is enabled (ie -pg
profiling using _mcount) we spill a stack frame on 64bit all the
time.
If a function calls __get_SP() and later calls a function that is
tail call optimised, we will pop the stack frame and the value
returned by __get_SP() is no longer valid. An example from Li can
be found in save_stack_trace -> save_context_stack:
c0000000000432c0 <.save_stack_trace>:
c0000000000432c0: mflr r0
c0000000000432c4: std r0,16(r1)
c0000000000432c8: stdu r1,-128(r1) <-- stack frame for _mcount
c0000000000432cc: std r3,112(r1)
c0000000000432d0: bl <._mcount>
c0000000000432d4: nop
c0000000000432d8: mr r4,r1 <-- __get_SP()
c0000000000432dc: ld r5,632(r13)
c0000000000432e0: ld r3,112(r1)
c0000000000432e4: li r6,1
c0000000000432e8: addi r1,r1,128 <-- pop stack frame
c0000000000432ec: ld r0,16(r1)
c0000000000432f0: mtlr r0
c0000000000432f4: b <.save_context_stack> <-- tail call optimized
save_context_stack ends up with a stack pointer below the current
one, and it is likely to be scribbled over.
Fix this by making __get_SP() a function which returns the
callers stack frame. Also replace inline assembly which grabs
the stack pointer in save_stack_trace and show_stack with
__get_SP().
This also fixes an issue with perf_arch_fetch_caller_regs().
It currently unwinds the stack once, which will skip a
valid stack frame on a leaf function. With the __get_SP() fixes
in this patch, we never need to unwind the stack frame to get
to the first interesting frame.
We have to export __get_SP() because perf_arch_fetch_caller_regs()
(which is used in modules) calls it from a header file.
Reported-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
|
|
In HMI interrupt handler we don't touch SRR0/SRR1, instead we touch
HSRR0/HSRR1. Hence we don't need to clear MSR_RI bit.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Merge patch-bomb from Andrew Morton:
- part of OCFS2 (review is laggy again)
- procfs
- slab
- all of MM
- zram, zbud
- various other random things: arch, filesystems.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
nosave: consolidate __nosave_{begin,end} in <asm/sections.h>
include/linux/screen_info.h: remove unused ORIG_* macros
kernel/sys.c: compat sysinfo syscall: fix undefined behavior
kernel/sys.c: whitespace fixes
acct: eliminate compile warning
kernel/async.c: switch to pr_foo()
include/linux/blkdev.h: use NULL instead of zero
include/linux/kernel.h: deduplicate code implementing clamp* macros
include/linux/kernel.h: rewrite min3, max3 and clamp using min and max
alpha: use Kbuild logic to include <asm-generic/sections.h>
frv: remove deprecated IRQF_DISABLED
frv: remove unused cpuinfo_frv and friends to fix future build error
zbud: avoid accessing last unused freelist
zsmalloc: simplify init_zspage free obj linking
mm/zsmalloc.c: correct comment for fullness group computation
zram: use notify_free to account all free notifications
zram: report maximum used memory
zram: zram memory size limitation
zsmalloc: change return value unit of zs_get_total_size_bytes
zsmalloc: move pages_allocated to zs_pool
...
|
|
The different architectures used their own (and different) declarations:
extern __visible const void __nosave_begin, __nosave_end;
extern const void __nosave_begin, __nosave_end;
extern long __nosave_begin, __nosave_end;
Consolidate them using the first variant in <asm/sections.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The interesting things here are:
- Turn on Config Request Retry Status Software Visibility. This
caused hangs last time, but we included a fix this time.
- Rework PCI device configuration to use _HPP/_HPX more aggressively
- Allow PCI devices to be put into D3cold during system suspend
- Add arm64 PCI support
- Add APM X-Gene host bridge driver
- Add TI Keystone host bridge driver
- Add Xilinx AXI host bridge driver
More detailed summary:
Enumeration
- Check Vendor ID only for Config Request Retry Status (Rajat Jain)
- Enable Config Request Retry Status when supported (Rajat Jain)
- Add generic domain handling (Catalin Marinas)
- Generate uppercase hex for modalias interface class (Ricardo Ribalda Delgado)
Resource management
- Add missing MEM_64 mask in pci_assign_unassigned_bridge_resources() (Yinghai Lu)
- Increase IBM ipr SAS Crocodile BARs to at least system page size (Douglas Lehr)
PCI device hotplug
- Prevent NULL dereference during pciehp probe (Andreas Noever)
- Move _HPP & _HPX handling into core (Bjorn Helgaas)
- Apply _HPP to PCIe devices as well as PCI (Bjorn Helgaas)
- Apply _HPP/_HPX to display devices (Bjorn Helgaas)
- Preserve SERR & PARITY settings when applying _HPP/_HPX (Bjorn Helgaas)
- Preserve MPS and MRRS settings when applying _HPP/_HPX (Bjorn Helgaas)
- Apply _HPP/_HPX to all devices, not just hot-added ones (Bjorn Helgaas)
- Fix wait time in pciehp timeout message (Yinghai Lu)
- Add more pciehp Slot Control debug output (Yinghai Lu)
- Stop disabling pciehp notifications during init (Yinghai Lu)
MSI
- Remove arch_msi_check_device() (Alexander Gordeev)
- Rename pci_msi_check_device() to pci_msi_supported() (Alexander Gordeev)
- Move D0 check into pci_msi_check_device() (Alexander Gordeev)
- Remove unused kobject from struct msi_desc (Yijing Wang)
- Remove "pos" from the struct msi_desc msi_attrib (Yijing Wang)
- Add "msi_bus" sysfs MSI/MSI-X control for endpoints (Yijing Wang)
- Use __get_cached_msi_msg() instead of get_cached_msi_msg() (Yijing Wang)
- Use __read_msi_msg() instead of read_msi_msg() (Yijing Wang)
- Use __write_msi_msg() instead of write_msi_msg() (Yijing Wang)
Power management
- Drop unused runtime PM support code for PCIe ports (Rafael J. Wysocki)
- Allow PCI devices to be put into D3cold during system suspend (Rafael J. Wysocki)
AER
- Add additional AER error strings (Gong Chen)
- Make <linux/aer.h> standalone includable (Thierry Reding)
Virtualization
- Add ACS quirk for Solarflare SFC9120 & SFC9140 (Alex Williamson)
- Add ACS quirk for Intel 10G NICs (Alex Williamson)
- Add ACS quirk for AMD A88X southbridge (Marti Raudsepp)
- Remove unused pci_find_upstream_pcie_bridge(), pci_get_dma_source() (Alex Williamson)
- Add device flag helpers (Ethan Zhao)
- Assume all Mellanox devices have broken INTx masking (Gavin Shan)
Generic host bridge driver
- Fix ioport_map() for !CONFIG_GENERIC_IOMAP (Liviu Dudau)
- Add pci_register_io_range() and pci_pio_to_address() (Liviu Dudau)
- Define PCI_IOBASE as the base of virtual PCI IO space (Liviu Dudau)
- Fix the conversion of IO ranges into IO resources (Liviu Dudau)
- Add pci_get_new_domain_nr() and of_get_pci_domain_nr() (Liviu Dudau)
- Add support for parsing PCI host bridge resources from DT (Liviu Dudau)
- Add pci_remap_iospace() to map bus I/O resources (Liviu Dudau)
- Add arm64 architectural support for PCI (Liviu Dudau)
APM X-Gene
- Add APM X-Gene PCIe driver (Tanmay Inamdar)
- Add arm64 DT APM X-Gene PCIe device tree nodes (Tanmay Inamdar)
Freescale i.MX6
- Probe in module_init(), not fs_initcall() (Lucas Stach)
- Delay enabling reference clock for SS until it stabilizes (Tim Harvey)
Marvell MVEBU
- Fix uninitialized variable in mvebu_get_tgt_attr() (Thomas Petazzoni)
NVIDIA Tegra
- Make sure the PCIe PLL is really reset (Eric Yuen)
- Add error path tegra_msi_teardown_irq() cleanup (Jisheng Zhang)
- Fix extended configuration space mapping (Peter Daifuku)
- Implement resource hierarchy (Thierry Reding)
- Clear CLKREQ# enable on port disable (Thierry Reding)
- Add Tegra124 support (Thierry Reding)
ST Microelectronics SPEAr13xx
- Pass config resource through reg property (Pratyush Anand)
Synopsys DesignWare
- Use NULL instead of false (Fabio Estevam)
- Parse bus-range property from devicetree (Lucas Stach)
- Use pci_create_root_bus() instead of pci_scan_root_bus() (Lucas Stach)
- Remove pci_assign_unassigned_resources() (Lucas Stach)
- Check private_data validity in single place (Lucas Stach)
- Setup and clear exactly one MSI at a time (Lucas Stach)
- Remove open-coded bitmap operations (Lucas Stach)
- Fix configuration base address when using 'reg' (Minghuan Lian)
- Fix IO resource end address calculation (Minghuan Lian)
- Rename get_msi_data() to get_msi_addr() (Minghuan Lian)
- Add get_msi_data() to pcie_host_ops (Minghuan Lian)
- Add support for v3.65 hardware (Murali Karicheri)
- Fold struct pcie_port_info into struct pcie_port (Pratyush Anand)
TI Keystone
- Add TI Keystone PCIe driver (Murali Karicheri)
- Limit MRSS for all downstream devices (Murali Karicheri)
- Assume controller is already in RC mode (Murali Karicheri)
- Set device ID based on SoC to support multiple ports (Murali Karicheri)
Xilinx AXI
- Add Xilinx AXI PCIe driver (Srikanth Thokala)
- Fix xilinx_pcie_assign_msi() return value test (Dan Carpenter)
Miscellaneous
- Clean up whitespace (Quentin Lambert)
- Remove assignments from "if" conditions (Quentin Lambert)
- Move PCI_VENDOR_ID_VMWARE to pci_ids.h (Francesco Ruggeri)
- x86: Mark DMI tables as initialization data (Mathias Krause)
- x86: Move __init annotation to the correct place (Mathias Krause)
- x86: Mark constants of pci_mmcfg_nvidia_mcp55() as __initconst (Mathias Krause)
- x86: Constify pci_mmcfg_probes[] array (Mathias Krause)
- x86: Mark PCI BIOS initialization code as such (Mathias Krause)
- Parenthesize PCI_DEVID and PCI_VPD_LRDT_ID parameters (Megan Kamiya)
- Remove unnecessary variable in pci_add_dynid() (Tobias Klauser)"
* tag 'pci-v3.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (109 commits)
arm64: dts: Add APM X-Gene PCIe device tree nodes
PCI: Add ACS quirk for AMD A88X southbridge devices
PCI: xgene: Add APM X-Gene PCIe driver
PCI: designware: Remove open-coded bitmap operations
PCI/MSI: Remove unnecessary temporary variable
PCI/MSI: Use __write_msi_msg() instead of write_msi_msg()
MSI/powerpc: Use __read_msi_msg() instead of read_msi_msg()
PCI/MSI: Use __get_cached_msi_msg() instead of get_cached_msi_msg()
PCI/MSI: Add "msi_bus" sysfs MSI/MSI-X control for endpoints
PCI/MSI: Remove "pos" from the struct msi_desc msi_attrib
PCI/MSI: Remove unused kobject from struct msi_desc
PCI/MSI: Rename pci_msi_check_device() to pci_msi_supported()
PCI/MSI: Move D0 check into pci_msi_check_device()
PCI/MSI: Remove arch_msi_check_device()
irqchip: armada-370-xp: Remove arch_msi_check_device()
PCI/MSI/PPC: Remove arch_msi_check_device()
arm64: Add architectural support for PCI
PCI: Add pci_remap_iospace() to map bus I/O resources
of/pci: Add support for parsing PCI host bridge resources from DT
of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()
...
Conflicts:
arch/arm64/boot/dts/apm-storm.dtsi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux.git
Freescale updates from Scott (27 commits):
"Highlights include DMA32 zone support (SATA, USB, etc now works on 64-bit
FSL kernels), MSI changes, 8xx optimizations and cleanup, t104x board
support, and PrPMC PCI enumeration."
|
|
For __ioremap().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pci_bus_find_capability() is decleared in pci.h, so it is not necessary to do
it again.
This patch removes it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add printk levels to some places in the powerpc port.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There is no need for yet another copy of the command line, just
use boot_command_line like everyone else.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Use pr_fmt to give some context to the error messages in the
module code, and convert open coded debug printk to pr_debug.
Use pr_err for error messages.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Move MSI checks from arch_msi_check_device() to arch_setup_msi_irqs().
This makes the code more compact and allows removing
arch_msi_check_device() from generic MSI code.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
As Michael suggested, the hex prefix for the output of EEH PE
state sysfs entry (/sys/bus/pci/devices/xxx/eeh_pe_state) is
always informative to users.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The dma_get_required_mask() function is used by some drivers to
query the platform about what DMA mask is needed to cover all of
memory. This is a bit of a strange semantic when we have to choose
between IOMMU translation or bypass, but essentially what it means
is "what DMA mask will give best performances".
Currently, our IOMMU backend always returns a 32-bit mask here, we
don't do anything special to it when we have bypass available. This
causes some drivers to choose a 32-bit mask, thus losing the ability
to use the bypass window, thinking this is more efficient. The problem
was reported from the driver of following device:
0004:03:00.0 0107: 1000:0087 (rev 05)
0004:03:00.0 Serial Attached SCSI controller: LSI Logic / Symbios \
Logic SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05)
This patch adds an override of that function in order to, instead,
return a 64-bit mask whenever a bypass window is available in order
for drivers to prefer this configuration.
Reported-by: Murali N. Iyer <mniyer@us.ibm.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The PEs can be organized as nested. Current implementation doesn't
dump PCI config space for subordinate devices of child PEs. However,
the frozen PE could be caused by those subordinate devices of its
child PEs.
The patch dumps PCI config space for all subordinate devices of the
problematic PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When enabling EEH functionality on passed through devices (PE)
with VFIO, the devices in the PE would be removed permanently
from guest side. In that case, the PE remains frozen state.
When returning PE to host, or restarting the guest again, we
had mechanism unfreezing the PE by clearing PESTA/B frozen
bits. However, that's not enough for some adapters, which are
indicated as following "lspci" shows. Those adapters require
hot reset on the parent bus to bring their firmware back to
workable state. Otherwise, those adaptrs won't be operative
and the host (for returning case) or the guest will fail to
load the drivers for those adapters without exception.
0000:01:00.0 Ethernet controller: Emulex Corporation OneConnect \
10Gb NIC (be3) (rev 02)
0000:01:00.0 0200: 19a2:0710 (rev 02)
0001:03:00.0 Ethernet controller: Emulex Corporation OneConnect \
NIC (Lancer) (rev 10)
0001:03:00.0 0200: 10df:e220 (rev 10)
The patch adds mechanism to emulate EEH recovery (for hot reset
on parent PCI bus) on 3 gates to fix the issue: open/release one
adapter of the PE, enable EEH functionality on one adapter of the
PE.
Reported-by: Murilo Fossa Vicentini <muvic@br.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PE would be owned by userland, which probably request PE reset
done in host side. During the reset, we should drop the PCI
config accesses to the PE with help of flag EEH_PE_RESET.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Function pcibios_set_pcie_reset_state() can be used to do PCI
reset. PCI config access during the reset usually causes EEH
errors unexpectedly. In order to avoid the EEH error, the patch
blocks PCI config access during reset with the help of flag
EEH_PE_RESET, which is similar to what we did in EEH PE reset
path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The patch uses eeh_unfreeze_pe() to replace the logic clearing
frozen IO and DMA, in order to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When passing through PE to guest, that's possibly in frozen
state. The driver for the pass-through devices on guest side
can't be loaded successfully as reported. We already had one
gate in eeh_dev_open() to clear PE frozen state accordingly,
but that's not enough because the function is only called at
QEMU startup for once.
The patch adds another gate in eeh_pe_set_option() so that the
PE frozen state can be cleared at QEMU restart time.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The function eeh_pci_enable() is called to apply various requests
to one particular PE: Enabling EEH, Disabling EEH, Enabling IO,
Enabling DMA, Freezing PE. When enabling IO or DMA on one specific
PE, we need check that IO or DMA isn't enabled previously. But
the condition used to do the check isn't completely correct because
one PE would be in DMA frozen state with workable IO path, or vice
versa.
The patch fixes the improper condition.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The problem was reported by Carol: In the scenario of passing mlx4
adapter to guest, EEH error could be recovered successfully. When
returning the device back to host, the driver (mlx4_core.ko)
couldn't be loaded successfully because of error number -5 (-EIO)
returned from mlx4_get_ownership(), which hits offlined PCI device.
The root cause is that we missed to put the affected devices into
normal state on clearing PE isolated state right after PE reset.
The patch fixes above issue by putting the affected devices to
normal state when clearing PE isolated state in eeh_pe_state_clear().
Cc: stable@vger.kernel.org
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When passing through device, its PE might have been put into frozen
state. One obvious example would be: the passed PE is forced to be
offline because of hitting maximal allowed EEH errors in userland.
In that case, the frozen state won't be cleared and then the PE is
returned back to host, which might not have chance detecting and
recovering from it.
The patch adds more check when passing through device and clear the
PE frozen state if necessary.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The PCI devices that have been passed through are enabled before
reset, we need restore to the enabled state after reset. Otherwise,
MMIO access might be issued to disabled devices after reset and
causes exceptional recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The patch adds one more option (EEH_OPT_FREEZE_PE) to set_option()
method to proactively freeze PE, which will be issued before resetting
pass-throughed PE to drop MMIO access during reset because it's
always contributing to recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The patch adds sysfs entry "eeh_pe_state". Reading on it returns
the PE's state while writing to it clears the frozen state. It's
used to check or clear the PE frozen state from userland for
debugging purpose.
The patch also replaces printk(KERN_WARNING ...) with pr_warn() in
eeh_sysfs.c
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
eeh_check_failure() is used to check frozen state of the PE which
owns the indicated I/O address. The argument "val" of the function
isn't used. The patch drops it and return the frozen state of the
PE as expected.
Cc: Vishal Mansur <vmansur@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When doing vfio passthrough a VF, the kernel will crash with following
message:
[ 442.656459] Unable to handle kernel paging request for data at address 0x00000060
[ 442.656593] Faulting instruction address: 0xc000000000038b88
[ 442.656706] Oops: Kernel access of bad area, sig: 11 [#1]
[ 442.656798] SMP NR_CPUS=1024 NUMA PowerNV
[ 442.656890] Modules linked in: vfio_pci mlx4_core nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT xt_conntrack bnep bluetooth rfkill ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw tg3 nfsd be2net nfs_acl ses lockd ptp enclosure pps_core kvm_hv kvm_pr shpchp binfmt_misc kvm sunrpc uinput lpfc scsi_transport_fc ipr scsi_tgt [last unloaded: mlx4_core]
[ 442.658152] CPU: 40 PID: 14948 Comm: qemu-system-ppc Not tainted 3.10.42yw-pkvm+ #37
[ 442.658219] task: c000000f7e2a9a00 ti: c000000f6dc3c000 task.ti: c000000f6dc3c000
[ 442.658287] NIP: c000000000038b88 LR: c0000000004435a8 CTR: c000000000455bc0
[ 442.658352] REGS: c000000f6dc3f580 TRAP: 0300 Not tainted (3.10.42yw-pkvm+)
[ 442.658419] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 28004882 XER: 20000000
[ 442.658577] CFAR: c00000000000908c DAR: 0000000000000060 DSISR: 40000000 SOFTE: 1
GPR00: c0000000004435a8 c000000f6dc3f800 c0000000012b1c10 c00000000da24000
GPR04: 0000000000000003 0000000000001004 00000000000015b3 000000000000ffff
GPR08: c00000000127f5d8 0000000000000000 000000000000ffff 0000000000000000
GPR12: c000000000068078 c00000000fdd6800 000001003c320c80 000001003c3607f0
GPR16: 0000000000000001 00000000105480c8 000000001055aaa8 000001003c31ab18
GPR20: 000001003c10fb40 000001003c360ae8 000000001063bcf0 000000001063bdb0
GPR24: 000001003c15ed70 0000000010548f40 c000001fe5514c88 c000001fe5514cb0
GPR28: c00000000da24000 0000000000000000 c00000000da24000 0000000000000003
[ 442.659471] NIP [c000000000038b88] .pcibios_set_pcie_reset_state+0x28/0x130
[ 442.659530] LR [c0000000004435a8] .pci_set_pcie_reset_state+0x28/0x40
[ 442.659585] Call Trace:
[ 442.659610] [c000000f6dc3f800] [00000000000719e0] 0x719e0 (unreliable)
[ 442.659677] [c000000f6dc3f880] [c0000000004435a8] .pci_set_pcie_reset_state+0x28/0x40
[ 442.659757] [c000000f6dc3f900] [c000000000455bf8] .reset_fundamental+0x38/0x80
[ 442.659835] [c000000f6dc3f980] [c0000000004562a8] .pci_dev_specific_reset+0xa8/0xf0
[ 442.659913] [c000000f6dc3fa00] [c0000000004448c4] .__pci_dev_reset+0x44/0x430
[ 442.659980] [c000000f6dc3fab0] [c000000000444d5c] .pci_reset_function+0x7c/0xc0
[ 442.660059] [c000000f6dc3fb30] [d00000001c141ab8] .vfio_pci_open+0xe8/0x2b0 [vfio_pci]
[ 442.660139] [c000000f6dc3fbd0] [c000000000586c30] .vfio_group_fops_unl_ioctl+0x3a0/0x630
[ 442.660219] [c000000f6dc3fc90] [c000000000255fbc] .do_vfs_ioctl+0x4ec/0x7c0
[ 442.660286] [c000000f6dc3fd80] [c000000000256364] .SyS_ioctl+0xd4/0xf0
[ 442.660354] [c000000f6dc3fe30] [c000000000009e54] syscall_exit+0x0/0x98
[ 442.660420] Instruction dump:
[ 442.660454] 4bfffce9 4bfffee4 7c0802a6 fbc1fff0 fbe1fff8 f8010010 f821ff81 7c7e1b78
[ 442.660566] 7c9f2378 60000000 60000000 e93e02c8 <e8690060> 2fa30000 41de00c4 2b9f0002
[ 442.660679] ---[ end trace a64ac9546bcf0328 ]---
[ 442.660724]
The reason is current VF is not EEH enabled.
This patch introduces a macro to convert eeh_dev to eeh_pe. By doing so, it
will prevent converting with NULL pointer.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
CC: Michael Ellerman <mpe@ellerman.id.au>
V3 -> V4:
1. move the macro definition from include/linux/pci.h to
arch/powerpc/include/asm/eeh.h
V2 -> V3:
1. rebased on 3.17-rc4
2. introduce a macro
3. use this macro in several other places
V1 -> V2:
1. code style and patch subject adjustment
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
"Helps debug funky firmware issues".
After:
Starting Linux PPC64 #108 SMP Wed Aug 6 19:04:51 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
phys_mem_size = 0x200000000
cpu_features = 0x17fc7a6c18500249
possible = 0x1fffffff18700649
always = 0x0000000000000040
cpu_user_features = 0xdc0065c2 0xee000000
mmu_features = 0x5a000001
firmware_features = 0x00000001405a440b
htab_hash_mask = 0x7ffff
-----------------------------------------------------
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.
At the moment they are very widely spaced, so that we can accommodate
the line:
ppc64_caches.dcache_line_size = 0xYY
But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.
The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.
Before:
Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
physicalMemorySize = 0x200000000
ppc64_caches.dcache_line_size = 0xf0
ppc64_caches.icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
After:
Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
phys_mem_size = 0x200000000
dcache_line_size = 0xf0
icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
This patch is final, no bike shedding ;)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().
With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.
For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084b6ad.
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In commit e6a6928c3ea1 "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.
There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.
The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.
We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
