| Age | Commit message (Collapse) | Author |
|---|
|
Convert tile to use clocksource_register_hz.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This change adds a number of missing headers in asm (fb.h, parport.h,
serial.h, and vga.h) using the minimal generic versions.
It also adds a number of missing interfaces that showed up as build
failures when trying to build various drivers not normally included in the
"tile" distribution: ioremap_wc(), memset_io(), io{read,write}{16,32}be(),
virt_to_bus(), bus_to_virt(), irq_canonicalize(), __pte(), __pgd(),
and __pmd(). I also added a cast in virt_to_page() since not all callers
pass a pointer.
I fixed <asm/stat.h> to properly include a __KERNEL__ guard for the
__ARCH_WANT_STAT64 symbol, and <asm/swab.h> to use __builtin_bswap32()
even for our 64-bit architecture, since the same code is produced.
I added an export for get_cycles(), since it's used in some modules.
And I made <arch/spr_def.h> properly include the __KERNEL__ guard,
even though it's not yet exported, since it likely will be soon.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The current implementations of __ndelay and __udelay call a hypervisor
service to delay, but the hypervisor service isn't actually implemented
very well, and the consensus is that Linux should handle figuring this
out natively and not use a hypervisor service.
By converting nanoseconds to cycles, and then spinning until the
cycle counter reaches the desired cycle, we get several benefits:
first, we are sensitive to the actual clock speed; second, we use
less power by issuing a slow SPR read once every six cycles while
we delay; and third, we properly handle the case of an interrupt by
exiting at the target time rather than after some number of cycles.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This completes the tile migration to the new naming scheme for
the architecture-specific irq management code.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
We were using the same 5-sec minsec for the clocksource and sched_clock
that we were using for the clock_event_device. For the clock_event_device
that's exactly right since it has a short maximum countdown time.
But for sched_clock we want to avoid wraparound when converting from
ticks to nsec over a much longer window, so we force a shift of 10.
And for clocksource it seems dodgy to use a 5-sec minsec as well, so we
copy some other platforms and force a shift of 22.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This commit is primarily changes caused by reviewing "sparse"
and "checkpatch" output on our sources, so is somewhat noisy, since
things like "printk() -> pr_err()" (or whatever) throughout the
codebase tend to get tedious to read. Rather than trying to tease
apart precisely which things changed due to which type of code
review, this commit includes various cleanups in the code:
- sparse: Add declarations in headers for globals.
- sparse: Fix __user annotations.
- sparse: Using gfp_t consistently instead of int.
- sparse: removing functions not actually used.
- checkpatch: Clean up printk() warnings by using pr_info(), etc.;
also avoid partial-line printks except in bootup code.
- checkpatch: Use exposed structs rather than typedefs.
- checkpatch: Change some C99 comments to C89 comments.
In addition, a couple of minor other changes are rolled in
to this commit:
- Add support for a "raise" instruction to cause SIGFPE, etc., to be raised.
- Remove some compat code that is unnecessary when we fully eliminate
some of the deprecated syscalls from the generic syscall ABI.
- Update the tile_defconfig to reflect current config contents.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.
This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
|
