| Age | Commit message (Collapse) | Author |
|---|
|
patch edaf420fdc122e7a42326fe39274c8b8c9b19d41 in mainline.
I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.
On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow. After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:
Test was done on a 2000 Mhz Xeon system. Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 21 3.048%
1999800 - 1999850 166 24.128%
1999850 - 1999900 241 35.029%
1999900 - 1999950 211 30.669%
1999950 - 2000000 42 6.105%
2000000 - 2000000 0 0.000%
2000050 - 2000100 0 0.000%
[...]
2000100 - 2015000 1 0.145% << BAD
2015000 - 2030000 6 0.872% << BAD
2030000 - 2045000 1 0.145% << BAD
2045000 < 0 0.000%
The worst boot was 2032.577 Mhz, over 1.5% off!
It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.
I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop. This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.
The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops. If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.
With the patch applied, 300 boots of the same system produce good
results:
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 30 10.000%
1999800 - 1999850 166 55.333%
1999850 - 1999900 89 29.667%
1999900 - 1999950 15 5.000%
1999950 < 0 0.000%
Problem was found and tested against 2.6.18. Patch is against 2.6.22.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
patch 6a22c57b8d2a62dea7280a6b2ac807a539ef0716 in mainline.
This reverts commit 2e1c49db4c640b35df13889b86b9d62215ade4b6.
First off, testing in Fedora has shown it to cause boot failures,
bisected down by Martin Ebourne, and reported by Dave Jobes. So the
commit will likely be reverted in the 2.6.23 stable kernels.
Secondly, in the 2.6.24 model, x86-64 has now grown support for
SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the
bug is not visible any more, it's become invisible due to the code just
being irrelevant and no longer enabled on the only architecture that
this ever affected.
backported to 2.6.22 by Chuck Ebbert
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Martin Ebourne <fedora@ebourne.me.uk>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
patch 9a24d04a3c26c223f22493492c5c9085b8773d4a upstream
While we were reviewing pageattr_32/64.c for unification,
Thomas Gleixner noticed the following serious SMP bug in
global_flush_tlb():
down_read(&init_mm.mmap_sem);
list_replace_init(&deferred_pages, &l);
up_read(&init_mm.mmap_sem);
this is SMP-unsafe because list_replace_init() done on two CPUs in
parallel can corrupt the list.
This bug has been introduced about a year ago in the 64-bit tree:
commit ea7322decb974a4a3e804f96a0201e893ff88ce3
Author: Andi Kleen <ak@suse.de>
Date: Thu Dec 7 02:14:05 2006 +0100
[PATCH] x86-64: Speed and clean up cache flushing in change_page_attr
down_read(&init_mm.mmap_sem);
- dpage = xchg(&deferred_pages, NULL);
+ list_replace_init(&deferred_pages, &l);
up_read(&init_mm.mmap_sem);
the xchg() based version was SMP-safe, but list_replace_init() is not.
So this "cleanup" introduced a nasty bug.
why this bug never become prominent is a mystery - it can probably be
explained with the (still) relative obscurity of the x86_64 architecture.
the safe fix for now is to write-lock init_mm.mmap_sem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
patch cc75b92d11384ba14f93828a2a0040344ae872e7 in mainline.
Level type interrupts do not need to be resent. It was also found that
some chipsets get confused in case of the resend.
Mark the ioapic level type interrupts as such to avoid the resend
functionality in the generic irq code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
patch ba02946a903015840ef672ccc9dc8620a7e83de6 in mainline
Its legal for the stfiwx instruction to have RA = 0 as part of its
effective address calculation. This is illegal for all other XE
form instructions.
Add code to compute the proper effective address for stfiwx if
RA = 0 rather than treating it as illegal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
changeset 6536a6b331d3225921c398eb7c6e4ecedb9b05e0 from mainline
Thanks to Tom Callaway for the excellent bug report and
test case.
sys_ipc() has several problems, most to due with semaphore
call handling:
1) 'err' return should be a 'long'
2) "union semun" is passed in a register on 64-bit compared
to 32-bit which provides it on the stack and therefore
by reference
3) Second and third arguments to SEMCTL are swapped compared
to 32-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d3f7eae182b04997be19343a23f7009170f4f7a5 upstream
The Averatec 2370 and some other Turion laptop BIOS seems to program the
ENABLE_C1E MSR inconsistently between cores. This confuses the lapic
use heuristics because when C1E is enabled anywhere it seems to affect
the complete chip.
Use a global flag instead of a per cpu flag to handle this.
If any CPU has C1E enabled disabled lapic use.
Thanks to Cal Peake for debugging.
Cc: tglx@linutronix.de
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2cc7345ff71b27b5ac99e49ad7de39360042f601 in mainline
Subject: [PATCH] [SPARC64]: Fix booting on V100 systems.
On the root PCI bus, the OBP device tree lists device 3 twice.
Once as 'pm' and once as 'lomp'.
Everything goes downhill from there.
Ignore the second instance to workaround this.
Thanks to Kövedi_Krisztián for the bug report and
testing the fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0ee6c15e7ba7b36a217cdadb292eeaf32a057a59 in mainline.
When we flush register state for FP, Altivec, or SPE in flush_*_to_thread
we need to respect the task_struct that the caller has passed to us.
Most cases we are called with current, however sometimes (ptrace) we may
be passed a different task_struct.
This showed up when using gdbserver debugging a simple program that used
floating point. When gdb tried to show the FP regs they all showed up as
0, because the child's FP registers were never properly flushed to memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Strictly it's only needed for eax.
It actually does a little more than strictly needed -- the other registers
are already zero extended.
Also remove the now unnecessary and non functional compat task check
in ptrace.
This is CVE-2007-4573
Found by Wojciech Purczynski
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It didn't handle that case at all, and now dump_stack()
can be implemented directly as show_stack(current, NULL)
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Found this looping Ubuntu installs with VMI.
If unlucky enough to hit a vmalloc sync fault during a lazy mode
operation (from an IRQ handler for a module which was not yet populated
in current page directory, or from inside copy_one_pte, which touches
swap_map, and hit in an unused 4M region), the required PDE update would
never get flushed, causing an infinite page fault loop.
This bug affects any paravirt-ops backend which uses lazy updates, I
believe that makes it a bug in Xen, VMI and lguest. It only happens on
LOWMEM kernels.
Touching vmalloc memory in the middle of a lazy mode update can generate a
kernel PDE update, which must be flushed immediately. The fix is to leave
lazy mode when doing a vmalloc sync.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The new percpu code has apparently broken the doublefault handler
when CONFIG_DEBUG_SPINLOCK is set. Doublefault is handled by
a hardware task, making the check
SPIN_BUG_ON(lock->owner == current, lock, "recursion");
fault because it uses the FS register to access the percpu data
for current, and that register is zero in the new TSS. (The trace
I saw was on 2.6.20 where it was GS, but it looks like this will
still happen with FS on 2.6.22.)
Initializing FS in the doublefault_tss should fix it.
AK: Also fix broken ptr_ok() and turn printks into KERN_EMERG
AK: And add a PANIC prefix to make clear the system will hang
AK: (e.g. x86-64 will recover)
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I got an oops while booting a 32bit kernel on KVM because it doesn't
implement performance counters used by the NMI watchdog. Handle this
case.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Very old binutils (2.12.90...) seem to have trouble with newlines
in assembler macro invocation. They put them into the resulting
argument expansion. In this case this lead to a parse error because
a .rept expression ended up spread over multiple lines. Change the PMDS()
invocation to a single line.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Very old binutils have .cfi_startproc/endproc, but
no .cfi_rel_offset. Check for .cfi_rel_offset too.
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
From: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Revert 7e92b4fc345f5b6f57585fbe5ffdb0f24d7c9b26. It broke Sébastien Dugué's
machine and Jeff said (persuasively)
This seems like it will break decades-long-working stuff, in favor of
breaking new ground in our favorite area, "trusting the BIOS."
It's just not worth it for serial ports, IMO. Serial ports are something
that just shouldn't break at this late stage in the game. My new Intel
platform boxes don't even have serial ports, so I question the value of
messing with serial port probing even more... because... just wait a year,
and your box won't have a serial port either! :)
I certainly don't object to the use of platform devices (or isa_driver),
but the probe change seems questionable. That's sorta analagous to
rewriting the floppy driver probe routine. Sure you could do it... but why
risk all that damage and go through debugging all over again?
It seems clear from this report that we cannot, should not, trust BIOS for
something (a) so simple and (b) that has been working for over a decade.
Much discussion ensued and we've decided to have another go at all of this.
Cc: Sébastien Dugué <sebastien.dugue@bull.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
My "slices" address space management code that was added in 2.6.22
implementation of get_unmapped_area() doesn't properly check that the
size is a multiple of the requested page size. This allows userland to
create VMAs that aren't a multiple of the huge page size with hugetlbfs
(since hugetlbfs entirely relies on get_unmapped_area() to do that
checking) which leads to a kernel BUG() when such areas are torn down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit 3baee955953957be5496cd28e9c544d9db214262.
this was a mistake from the start; I added mdio type to the bus
scan list early on in my ucc_geth migrate to phylib development,
which is just pure wrong (the ucc_geth_mii driver creates the mii
bus and the PHY layer handles PHY enumeration without translation).
this accompanies commit 77926826f301fbd8ed96d3cd9ff17a5b59560dfb:
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
which was basically trying to hide a symptom of the original mistake
this revert fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit fd6e9d3945ee122eb513ada8b17296d243c1ce5e.
Having #size-cells == 0 in a node indicates that things under the
node aren't directly accessible, and therefore we shouldn't try to
translate addresses for devices under the node into CPU physical
addresses.
Some drivers, such as the nvram driver for powermacs, rely on
of_address_to_resource failing if they are called for a node
representing a device whose resources aren't directly accessible
by the CPU. These drivers were broken by commit fd6e9d39,
resulting in the "Lombard" powerbook hanging early in the boot
process.
stable team, this patch is equivalent to commit
77926826f301fbd8ed96d3cd9ff17a5b59560dfb
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add some exports for hostfs that are required after Alberto Bertogli's
fixes for accessing unlinked host files.
Also did some style cleanups while I was here.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
COWed devices can't handle more than 32 (64 on x86_64) sectors in one request
due to the size of the bitmap being carried around in the io_thread_req.
Enforce that by telling the block layer not to put too many sectors in
requests to COWed devices.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[CPUFREQ] acpi-cpufreq: Proper ReadModifyWrite of PERF_CTL MSR
During recent acpi-cpufreq changes, writing to PERF_CTL msr
changed from RMW of entire 64 bit to RMW of low 32 bit and clearing of
upper 32 bit. Fix it back to do a proper RMW of the MSR.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some systems have a HPET which is not incrementing, which leads to a
complete hang. Detect it during HPET setup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[SPARC32]: Fix rounding errors in ndelay/udelay implementation.
__ndelay and __udelay have not been delayung >= specified time.
The problem with __ndelay has been tacked down to the rounding of the
multiplier constant. By changing this, delays > app 18us are correctly
calculated.
The problem with __udelay has also been tracked down to rounding issues.
Changing the multiplier constant (to match that used in sparc64) corrects
for large delays and adding in a rounding constant corrects for trunctaion
errors in the claculations.
Many short delays will return without looping. This is not an error as there
is the fixed delay of doing all the maths to calculate the loop count.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[SPARC32]: Fix bug in sparc optimized memset.
Sparc optimized memset (arch/sparc/lib/memset.S) does not fill last
byte of the memory area, if area size is less than 8 bytes and start
address is not word (4-bytes) aligned.
Here is code chunk where bug located:
/* %o0 - memory address, %o1 - size, %g3 - value */
8:
add %o0, 1, %o0
subcc %o1, 1, %o1
bne,a 8b
stb %g3, [%o0 - 1]
This code should write byte every loop iteration, but last time delay
instruction stb is not executed because branch instruction sets
"annul" bit.
Patch replaces bne,a by bne instruction.
Error can be reproduced by simple kernel module:
--------------------
#include <linux/module.h>
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <string.h>
static void do_memset(void **p, int size)
{
memset(p, 0x00, size);
}
static int __init memset_test_init(void)
{
char fooc[8];
int *fooi;
memset(fooc, 0xba, sizeof(fooc));
do_memset((void**)(fooc + 3), 1);
fooi = (int*) fooc;
printk("%08X %08X\n", fooi[0], fooi[1]);
return -1;
}
static void __exit memset_test_cleanup(void)
{
return;
}
module_init(memset_test_init);
module_exit(memset_test_cleanup);
MODULE_LICENSE("GPL");
EXPORT_NO_SYMBOLS;
------------------------
Signed-off-by: Alexander Shmelev <ashmelev@task.sun.mcst.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[SPARC64]: Fix two year old bug in early bootup asm.
We try to fetch the CIF entry pointer from %o4, but that
can get clobbered by the early OBP calls. It is saved
in %l7 already, so actually this "mov %o4, %l7" can just
be completely removed with no other changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The printk level in this printk is bogus, as the previous printk
didn't have a terminating \n resulting in ..
Intel E7520/7320/7525 detected.<6>Disabling irq balancing and affinity
It also never printed a \n at all in the case where we didn't do
the quirk.
Change it to only make noise if it actually does something useful.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Writing to MSR 0x51400017 forces a hard reset on CS5536-based machines,
this has the reboot fixup do just that if such a board is detected.
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix scheduling latency issue on 24K, 34K and 74K cores
[MIPS] Add macros to encode processor revisions.
[MIPS] RM7000: Enable ICACHE_REFILLS_WORKAROUND_WAR.
[MIPS] SMTC: Fix cut'n'paste bug in Kconfig.debug
[MIPS] Change libgcc-style functions from lib-y to obj-y
[MIPS] Fix timer/performance interrupt detection
[MIPS] AP/SP: Avoid triggering the 34K E125 performance issue
[MIPS] 64-bit TO_PHYS_MASK macro for RM9000 processors
|
|
o Commit 1833d6bc72893265f22addd79cf52e6987496e0f broke the build if
compiled with CONFIG_ES7000=y and CONFIG_X86_GENERICARCH=n
arch/i386/kernel/built-in.o(.init.text+0x4fa9): In function `acpi_parse_madt':
: undefined reference to `acpi_madt_oem_check'
arch/i386/kernel/built-in.o(.init.text+0x7406): In function `smp_read_mpc':
: undefined reference to `mps_oem_check'
arch/i386/kernel/built-in.o(.init.text+0x8990): In function
`connect_bsp_APIC':
: undefined reference to `enable_apic_mode'
make: *** [.tmp_vmlinux1] Error 1
o Fix the build issue. Provided the definitions of missing functions.
o Don't have ES7000 machine. Only compile tested.
Cc: Len Brown <lenb@kernel.org>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Processors synchronization in set_mtrr requires the .gate field to be set
after .count field is properly initialized. Without an explicit barrier,
the compiler was reordering those memory stores. That was sometimes
causing a processor (in ipi_handler) to see the .gate change and decrement
.count before the latter is set by set_mtrr() (which then hangs in a
infinite loop with irqs disabled).
Signed-off-by: Loic Prylli <loic@myri.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The commit 635cf99a80f4ebee59d70eb64bb85ce829e4591f introduced a
regression. Executing a ptrace single step after certain int80
accesses will infinitely loop and never advance the PC.
The TIF_SINGLESTEP check should be done on the return from the syscall
and not before it.
I loops on each single step on the pop right after the int80 which writes out
to the console. At that point you can issue as many single steps as you want
and it will not advance any further.
The test case is below:
/* Test whether singlestep through an int80 syscall works.
*/
#define _GNU_SOURCE
#include <stdio.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/ptrace.h>
#include <sys/wait.h>
#include <sys/mman.h>
#include <asm/user.h>
#include <string.h>
static int child, status;
static struct user_regs_struct regs;
static void do_child()
{
char str[80] = "child: int80 test\n";
ptrace(PTRACE_TRACEME, 0, 0, 0);
kill(getpid(), SIGUSR1);
write(fileno(stdout),str,strlen(str));
asm ("int $0x80" : : "a" (20)); /* getpid */
}
static void do_parent()
{
unsigned long eip, expected = 0;
again:
waitpid(child, &status, 0);
if (WIFEXITED(status) || WIFSIGNALED(status))
return;
if (WIFSTOPPED(status)) {
ptrace(PTRACE_GETREGS, child, 0, ®s);
eip = regs.eip;
if (expected)
fprintf(stderr, "child stop @ %08lx, expected %08lx %s\n",
eip, expected,
eip == expected ? "" : " <== ERROR");
if (*(unsigned short *)eip == 0x80cd) {
fprintf(stderr, "int 0x80 at %08x\n", (unsigned int)eip);
expected = eip + 2;
} else
expected = 0;
ptrace(PTRACE_SINGLESTEP, child, NULL, NULL);
}
goto again;
}
int main(int argc, char * const argv[])
{
child = fork();
if (child)
do_parent();
else
do_child();
return 0;
}
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: <stable@kernel.org>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The idle loop goes to sleep using the WAIT instruction if !need_resched().
This has is suffering from from a race condition that if if just after
need_resched has returned 0 an interrupt might set TIF_NEED_RESCHED but
we've just completed the test so go to sleep anyway. This would be
trivial to fix by just disabling interrupts during that sequence as in:
local_irq_disable();
if (!need_resched())
__asm__("wait");
local_irq_enable();
but the processor architecture leaves it undefined if a processor calling
WAIT with interrupts disabled will ever restart its pipeline and indeed
some processors have made use of the freedom provided by the architecture
definition. This has been resolved and the Config7.WII bit indicates that
the use of WAIT is safe on 24K, 24KE and 34K cores. It also is safe on
74K starting revision 2.1.0 so enable the use of WAIT with interrupts
disabled for 74K based on a c0_prid of at least that.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This effectivly turned the SMTC_IDLE_HOOK_DEBUG debug option into a no-op.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Reported by Eugene Surovegin <ebs@ebshome.net>.
If only modules were users of these functions they did not get linked into
the kernel proper, so later module loads would fail as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
C0_status doesn't need to be initialized at this point anyway; the register
will be initialized later.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] always allow dump_stack() to produce a backtrace
[ARM] Fix non-page aligned boot time mappings
[ARM] 4458/1: pxa: Fix CKEN usage and hence fix pxa suspend/resume
[ARM] 4454/1: Use word accesses in Versatile PCI config reads
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Update defconfigs
[POWERPC] Uninline and export virq_to_hw() for the pasemi_mac driver
[POWERPC] Fix PMI breakage in cbe_cbufreq driver
[POWERPC] Disable old EMAC driver in arch/powerpc
|
|
Don't make this dependent on CONFIG_DEBUG_KERNEL - if we hit a WARN_ON
we need the stack trace to work out how we got to that point.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
AT91SAM9260 stopped booting with the recent changes to MM
initialisation - it was asking for a non-aligned virtual address
which caused loops to be non-terminal. Fix this by rounding
virtual addresses down, but remember to include the offset in
the length, and round the length up to the following page.
This means that asking for a mapping of 4K starting at 2K into
a page maps two pages as one would expect.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When Andi reverted the HPET resource reservation (in commit
0f8dc2f06560e2ca126d1670a24126ba08357d38), he didn't remove the now
unused variables, which just causes gcc to be noisy.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this change it works again when the nmi watchdog is disabled.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Matthias Lenk reports that the PCI subsystem would move the HPET on
SB400/SB600-based systems, where the HPET is in BAR1 of the SMbus
controller.
The reason? The ACPI layer registered the PCI MMIO range as being busy
too early, before PCI enumeration had happened, causing the PCI layer to
decide that it should relocate the resources somewhere else.
Firmware resources should be marked busy _after_ the PCI enumeration and
probing has happened, not before.
Remove the too-early reservation, we'll fix it up to do it properly
later. In the meantime, this solves the regression.
Tested-by: Matthias Lenk <matthias.lenk@amd.com>
Cc: Aaron Durbin <adurbin@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
