| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ]
Documentation states:
NOTE: There must be a correlation between the wake-up enable and
interrupt-enable registers. If a GPIO pin has a wake-up configured
on it, it must also have the corresponding interrupt enabled (on
one of the two interrupt lines).
Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt. This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.
If we do any clearing, clear between the interrupt enable/disable and
trigger setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ]
Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.
This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.
Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da38ef3ed10a09248e13ae16530c2c6d448dc47d ]
We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.
Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d01849f7deba81f4959fd9e51bf20dbf46987d1c ]
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Originally OMAP MPUIO GPIO irqchip was implemented using Generic irq
chip, but after set of reworks Generic irq chip code was replaced by
common OMAP GPIO implementation and finally removed by
commit d2d05c65c40e ("gpio: omap: Fix regression for MPUIO interrupts").
Unfortunately, above commit left .irq_mask/unmask callbacks assigned
as below for MPUIO GPIO case:
irqc->irq_mask = irq_gc_mask_set_bit;
irqc->irq_unmask = irq_gc_mask_clr_bit;
This now causes boot failure on OMAP1 platforms, after
commit 450fa54cfd66 ("gpio: omap: convert to use generic irq handler")
which forces these callbacks to be called during GPIO IRQs mapping
from gpiochip_irq_map:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 75 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-rc1-e3-los_afe0c+-00002-g25379c0-dirty #1
Hardware name: Amstrad E3 (Delta)
task: c1836000 ti: c1838000 task.ti: c1838000
PC is at irq_gc_mask_set_bit+0x1c/0x60
LR is at __irq_do_set_handler+0x118/0x15c
pc : [<c004848c>] lr : [<c0047d4c>] psr: 600000d3
sp : c1839c90 ip : c1862c64 fp : c1839c9c
r10: 00000000 r9 : c0411950 r8 : c0411bbc
r7 : 00000000 r6 : c185c310 r5 : c00444e8 r4 : c185c300
r3 : c1854b50 r2 : 00000000 r1 : 00000000 r0 : c185c310
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 0000317f Table: 10004000 DAC: 00000057
Process swapper (pid: 1, stack limit = 0xc1838190)
Stack: (0xc1839c90 to 0xc183a000)
[...]
Backtrace:
[<c0048470>] (irq_gc_mask_set_bit) from [<c0047d4c>] (__irq_do_set_handler+0x118/0x15c)
[<c0047c34>] (__irq_do_set_handler) from [<c0047dd4>] (__irq_set_handler+0x44/0x5c)
r6:00000000 r5:c00444e8 r4:c185c300
[<c0047d90>] (__irq_set_handler) from [<c0047e1c>] (irq_set_chip_and_handler_name+0x30/0x34)
r7:00000050 r6:00000000 r5:c00444e8 r4:00000050
[<c0047dec>] (irq_set_chip_and_handler_name) from [<c01b345c>] (gpiochip_irq_map+0x3c/0x8c)
r7:00000050 r6:00000000 r5:00000050 r4:c1862c64
[<c01b3420>] (gpiochip_irq_map) from [<c0049670>] (irq_domain_associate+0x7c/0x1c4)
r5:c185c310 r4:c185cb00
[<c00495f4>] (irq_domain_associate) from [<c0049894>] (irq_domain_add_simple+0x98/0xc0)
r8:c0411bbc r7:c185cb00 r6:00000050 r5:00000010 r4:00000001
[<c00497fc>] (irq_domain_add_simple) from [<c01b3328>] (_gpiochip_irqchip_add+0x64/0x10c)
r7:c1862c64 r6:c0419280 r5:c1862c64 r4:c1854b50
[<c01b32c4>] (_gpiochip_irqchip_add) from [<c01b79f4>] (omap_gpio_probe+0x2fc/0x63c)
r5:c1854b50 r4:c1862c10
[<c01b76f8>] (omap_gpio_probe) from [<c01fcf58>] (platform_drv_probe+0x2c/0x64)
r10:00000000 r9:c03e45e8 r8:00000000 r7:c0419294 r6:c0411984 r5:c0419294
r4:c0411950
[<c01fcf2c>] (platform_drv_probe) from [<c01fb668>] (really_probe+0x160/0x29c)
Hence, fix it by remove obsolete callbacks assignment. After this
change omap_gpio_mask_irq()/omap_gpio_unmask_irq() will be used
for MPUIO IRQs masking, but this now happens anyway from
omap_gpio_irq_startup/shutdown().
Cc: Tony Lindgren <tony@atomide.com>
Fixes: commit d2d05c65c40e ("gpio: omap: Fix regression for MPUIO interrupts")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes below static checker warning by changing
type of irq field in struct gpio_bank from u16 to int.
drivers/gpio/gpio-omap.c:1191 omap_gpio_probe()
warn: assigning (-6) to unsigned variable 'bank->irq'
drivers/gpio/gpio-omap.c
1188 bank->irq = platform_get_irq(pdev, 0);
1189 if (bank->irq <= 0) {
bank->irq is u16.
1190 if (!bank->irq)
1191 bank->irq = -ENXIO;
Does not work.
1192 if (bank->irq != -EPROBE_DEFER)
Does not work.
1193 dev_err(dev,
1194 "can't get irq resource ret=%d\n", bank->irq);
1195 return bank->irq;
1196 }
Fixes: commit 89d18e3af8b9: "gpio: omap: switch to use platform_get_irq"
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch converts TI OMAP GPIO driver to use generic irq handler
instead of chained IRQ handler. This way OMAP GPIO driver will be
compatible with RT kernel where it will be forced thread IRQ handler
while in non-RT kernel it still will be executed in HW IRQ context.
As part of this change the IRQ wakeup configuration is applied to
GPIO Bank IRQ as it now will be under control of IRQ PM Core during
suspend.
There are also additional benefits:
- on-RT kernel there will be no complains any more about PM runtime usage
in atomic context "BUG: sleeping function called from invalid context";
- GPIO bank IRQs will appear in /proc/interrupts and its usage statistic
will be visible;
- GPIO bank IRQs could be configured through IRQ proc_fs interface and,
as result, could be a part of IRQ balancing process if needed;
- GPIO bank IRQs will be under control of IRQ PM Core during
suspend to RAM.
Disadvantage:
- additional runtime overhed as call chain till
omap_gpio_irq_handler() will be longer now
- necessity to use wa_lock in omap_gpio_irq_handler() to W/A warning
in handle_irq_event_percpu()
WARNING: CPU: 1 PID: 35 at kernel/irq/handle.c:149 handle_irq_event_percpu+0x51c/0x638()
This patch doesn't fully follows recommendations provided by Sebastian
Andrzej Siewior [1], because It's required to go through and check all
GPIO IRQ pin states as fast as possible and pass control to handle_level_irq
or handle_edge_irq. handle_level_irq or handle_edge_irq will perform actions
specific for IRQ triggering type and wakeup corresponding registered
threaded IRQ handler (at least it's expected to be threaded).
IRQs can be lost if handle_nested_irq() will be used, because excecution
time of some pin specific GPIO IRQ handler can be very significant and
require accessing ext. devices (I2C).
Idea of such kind reworking was also discussed in [2].
[1] http://www.spinics.net/lists/linux-omap/msg120665.html
[2] http://www.spinics.net/lists/linux-omap/msg119516.html
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PM runtime API can't be used in atomic contex on -RT even if
it's configured as irqsafe. As result, below error report can
be seen when PM runtime API called from IRQ chip's callbacks
irq_startup/irq_shutdown/irq_set_type, because they are
protected by RAW spinlock:
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 128, pid: 96, name: insmod
3 locks held by insmod/96:
#0: (&dev->mutex){......}, at: [<c04752c8>] __driver_attach+0x54/0xa0
#1: (&dev->mutex){......}, at: [<c04752d4>] __driver_attach+0x60/0xa0
#2: (class){......}, at: [<c00a408c>] __irq_get_desc_lock+0x60/0xa4
irq event stamp: 1834
hardirqs last enabled at (1833): [<c06ab2a4>] _raw_spin_unlock_irqrestore+0x88/0x90
hardirqs last disabled at (1834): [<c06ab068>] _raw_spin_lock_irqsave+0x2c/0x64
softirqs last enabled at (0): [<c003d220>] copy_process.part.52+0x410/0x19d8
softirqs last disabled at (0): [< (null)>] (null)
Preemption disabled at:[< (null)>] (null)
CPU: 1 PID: 96 Comm: insmod Tainted: G W O 4.1.3-rt3-00618-g57e2387-dirty #184
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c00190f4>] (unwind_backtrace) from [<c0014734>] (show_stack+0x20/0x24)
[<c0014734>] (show_stack) from [<c06a62ec>] (dump_stack+0x88/0xdc)
[<c06a62ec>] (dump_stack) from [<c006ca44>] (___might_sleep+0x198/0x2a8)
[<c006ca44>] (___might_sleep) from [<c06ab6d4>] (rt_spin_lock+0x30/0x70)
[<c06ab6d4>] (rt_spin_lock) from [<c04815ac>] (__pm_runtime_resume+0x68/0xa4)
[<c04815ac>] (__pm_runtime_resume) from [<c04123f4>] (omap_gpio_irq_type+0x188/0x1d8)
[<c04123f4>] (omap_gpio_irq_type) from [<c00a64e4>] (__irq_set_trigger+0x68/0x130)
[<c00a64e4>] (__irq_set_trigger) from [<c00a7bc4>] (irq_set_irq_type+0x44/0x6c)
[<c00a7bc4>] (irq_set_irq_type) from [<c00abbf8>] (irq_create_of_mapping+0x120/0x174)
[<c00abbf8>] (irq_create_of_mapping) from [<c0577b74>] (of_irq_get+0x48/0x58)
[<c0577b74>] (of_irq_get) from [<c0540a14>] (i2c_device_probe+0x54/0x15c)
[<c0540a14>] (i2c_device_probe) from [<c04750dc>] (driver_probe_device+0x184/0x2c8)
[<c04750dc>] (driver_probe_device) from [<c0475310>] (__driver_attach+0x9c/0xa0)
[<c0475310>] (__driver_attach) from [<c0473238>] (bus_for_each_dev+0x7c/0xb0)
[<c0473238>] (bus_for_each_dev) from [<c0474af4>] (driver_attach+0x28/0x30)
[<c0474af4>] (driver_attach) from [<c0474760>] (bus_add_driver+0x154/0x200)
[<c0474760>] (bus_add_driver) from [<c0476348>] (driver_register+0x88/0x108)
[<c0476348>] (driver_register) from [<c0541600>] (i2c_register_driver+0x3c/0x90)
[<c0541600>] (i2c_register_driver) from [<bf003018>] (pcf857x_init+0x18/0x24 [gpio_pcf857x])
[<bf003018>] (pcf857x_init [gpio_pcf857x]) from [<c000998c>] (do_one_initcall+0x128/0x1e8)
[<c000998c>] (do_one_initcall) from [<c06a4220>] (do_init_module+0x6c/0x1bc)
[<c06a4220>] (do_init_module) from [<c00dd0c8>] (load_module+0x18e8/0x21c4)
[<c00dd0c8>] (load_module) from [<c00ddaa0>] (SyS_init_module+0xfc/0x158)
[<c00ddaa0>] (SyS_init_module) from [<c000ff40>] (ret_fast_syscall+0x0/0x54)
The IRQ chip interface defines only two callbacks which are executed in
non-atomic contex - irq_bus_lock/irq_bus_sync_unlock, so lets move
PM runtime calls there.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
|
|
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
If gpio-omap probe fails with -EPROBE_DEFER, the GPIO numbering
keeps increasing. Only increase the gpio count if gpiochip_add()
was successful as otherwise the numbers will increase for each
probe attempt.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently we gpio-omap breaks if gpiochip_add() returns -EPROBE_DEFER:
[ 0.570000] gpiochip_add: GPIOs 0..31 (gpio) failed to register
[ 0.570000] omap_gpio 48310000.gpio: Could not register gpio chip -517
...
[ 3.670000] omap_gpio 48310000.gpio: Unbalanced pm_runtime_enable!
Let's fix the issue by adding the missing pm_runtime_put() on error.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As per CCF documentation (clk.txt) the clk_prepare/unprepare APIs
are not allowed in atomic context. But now OMAP GPIO driver
uses them while applying debounce settings and as part
of PM runtime irqsafe operations:
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
- pm_runtime_get_sync() is holding the lock with IRQs off
+ omap_gpio_runtime_suspend()
+ raw_spin_lock_irqsave()
+ omap_gpio_dbck_disable()
+ clk_disable_unprepare()
Hence, fix it by moeving dbclk prepare/unprepare in OMAP GPIO
omap_gpio_probe/omap_gpio_remove. Also, while here, ensure that
debounce functionality is disabled if clk_get() failed,
because otherwise kernel will carsh in omap2_set_gpio_debounce().
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The access to HW registers has to be be protected in
omap_gpio_irq_handler(), as it may race with code executed on
another CPUs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
According to TRMs:
Required input line stable =
(the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME + 1) × 31,
where the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME bit field
is from 0 to 255.
But now omap2_set_gpio_debounce() will calculate debounce time and
behave incorrectly in the following cases:
1) requested debounce time is !0 and <32
calculated DEBOUNCETIME = 0x1 == 62 us;
expected value of DEBOUNCETIME = 0x0 == 31us
2) requested debounce time is 0
calculated DEBOUNCETIME = 0x1 == 62 us;
expected: disable debounce and DEBOUNCETIME = 0x0
3) requested debounce time is >32 and <63
calculated DEBOUNCETIME = 0x0 and debounce will be disabled;
expected: enable debounce and DEBOUNCETIME = 0x1 == 62 us
Hence, rework omap2_set_gpio_debounce() to fix above cases:
1) introduce local variable "enable" and use it to identify
when debounce need to be enabled or disabled. Disable debounce
if requested debounce time is 0.
2) use below formula for debounce time calculation:
debounce = (DIV_ROUND_UP(debounce, 31) - 1) & 0xFF;
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Switch OMAP GPIO driver to use platform_get_irq(), because
it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
for requesting IRQ resources any more, as they can be not ready yet
in case of DT-boot.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The bank->chip.irqdomain is uninitialized at the moment when
irq_domain_remove() is called, so remove this call.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix below build warning:
CC drivers/gpio/gpio-omap.o
drivers/gpio/gpio-omap.c: In function 'omap_gpio_irq_type':
drivers/gpio/gpio-omap.c:504:3: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type [enabled by default]
include/linux/spinlock.h:360:29: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
Fixes: commit 4dbada2be460 ("gpio: omap: use raw locks for locking")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.2-rc4
|
|
This patch converts gpio_bank.lock from a spin_lock into a
raw_spin_lock. The call path is to access this lock is always under a
raw_spin_lock, for instance
- __setup_irq() holds &desc->lock with irq off
+ __irq_set_trigger()
+ omap_gpio_irq_type()
- handle_level_irq() (runs with irqs off therefore raw locks)
+ mask_ack_irq()
+ omap_gpio_mask_irq()
This fixes the obvious backtrace on -RT. However the locking vs context
is not and this is not limited to -RT:
- omap_gpio_irq_type() is called with IRQ off and has an conditional
call to pm_runtime_get_sync() which may sleep. Either it may happen or
it may not happen but pm_runtime_get_sync() should not be called with
irqs off.
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
The number of users of gpiod_set_debounce() / gpio_set_debounce()
looks low but still this is not good.
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
OMAP GPIO driver allowed to be built as loadable module, but it
doesn't set owner field in GPIO chip structure. As result,
module_get/put() API is not working and it's possible to unload
OMAP driver while in use:
omap_gpio 48051000.gpio: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
Hence, add missing configuration.
Cc: Tony Lindgren <tony@atomide.com>
Fixes: cac089f9026e ('gpio: omap: Allow building as a loadable module')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missed spin_unlock_irqrestore in omap_gpio_irq_type when
omap_set_gpio_triggering() is failed.
It fixes static checker warning:
drivers/gpio/gpio-omap.c:523 omap_gpio_irq_type()
warn: inconsistent returns 'spin_lock:&bank->lock'.
This fixes commit:
1562e4618ded ('gpio: omap: fix error handling in omap_gpio_irq_type')
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Preparatory patch for the removal of the 'irq' argument from irq flow
handlers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
|
|
The omap_gpio_irq_startup() can be called at time when:
- corresponding GPIO has been requested already and in this case
it has to be configured as input already. If not - return with -EINVAL
and do not try to re-configure it as it could be unsafe.
- corresponding GPIO is free: reconfigure GPIO as input.
In addition, call omap_enable_gpio_module directly as all needed
checks are already present inside it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO Chip implementation shouldn't touch GPIO IRQ specific registers
and vise versa.
Hence, rework omap_gpio_request:
- don't reset GPIO IRQ triggering type to IRQ_TYPE_NONE, because
GPIO irqchip should be responsible for that;
- call directly omap_enable_gpio_module as all needed checks are already
present inside it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO IRQ Chip implementation shouldn't touch GPIO specific
registers and vise versa.
Hence, rework omap_gpio_irq_shutdown and try to touch only irqs specific
registers:
- don't configure GPIO as input (it, actually, should be already configured
as input).
- don't clear debounce configuration if GPIO is still used as GPIO.
We need to take in to account here commit c9c55d921115
("gpio/omap: fix off-mode bug: clear debounce settings on free/reset").
Also remove omap_reset_gpio() function as it is not used any more.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO bank will be kept powered in case if input parameters
are invalid or error occurred in omap_gpio_irq_type.
Hence, fix it by ensuring that GPIO bank will be unpowered
in case of errors and add additional check of value returned
from omap_set_gpio_triggering().
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes following issue:
- GPIOn is used as IRQ by some dev, for example PCF8575.INT -> gpio6.11
- PCFx driver knows nothing about type of IRQ line (GPIO or not)
so it doesn't request gpio and just do request_irq()
- If gpio6.11 will be exported through the sysfs and then un-xeported
then IRQs from PCFx will not be received any more, because
IRQ configuration for gpio6.11 will be cleaned up unconditionally
in omap_gpio_free.
Fix this by removing all GPIO IRQ specific code from omap_gpio_free()
and also do GPIO clean up (change direction to 'in' and disable debounce)
only if corresponding GPIO is not used as IRQ too.
GPIO IRQ will be properly cleaned up by GPIO irqchip code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.1-rc3
|
|
We currently get all kinds of errors building the omap gpio driver
as a module starting with:
undefined reference to `omap2_gpio_resume_after_idle'
undefined reference to `omap2_gpio_prepare_for_idle'
...
Let's fix the issue by adding inline functions to the header.
Note that we can now also remove the two unused functions for
omap_set_gpio_debounce and omap_set_gpio_debounce_time.
Then doing rmmod on the module produces further warnings
because of missing exit related functions. Let's add those.
And finally, we can make the Kconfig entry just a tristate
option that's selected for omaps.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
At some point with all the GPIO clean-up we've broken the
MPUIO interrupts. Those are just a little bit different from
the GPIO interrupts, so we can fix it up just by setting
different irqchip functions for it. And then we can just
remove all old code trying to do the same.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now OMAP GPIO driver prepared for GPIO_INDEX() macro removing.
Do It ;)
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now OMAP GPIO driver prepared for omap_irq_to_gpio() removing.
Do it ;)
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now OMAP GPIO driver prepared for GPIO_BIT() macro removing.
Do it ;)
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Convert GPIO IRQ functions to use GPIO offset instead of system
GPIO numbers. This allows to drop unneeded conversations between
system GPIO <-> GPIO offset which are done in many places and
many times.
It is safe to do now because:
- gpiolib always passes GPIO offset to GPIO controller
- OMAP GPIO driver converted to use IRQ domain, so
struct irq_data->hwirq contains GPIO offset
This is preparation step before removing:
#define GPIO_INDEX(bank, gpio)
#define GPIO_BIT(bank, gpio)
int omap_irq_to_gpio()
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The 'gpio' parameter isn't needed any more as it
duplicates 'offset' parameter, so drop it.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Convert debounce functions to use GPIO offset instead of system
GPIO numbers. This allows to drop unneeded conversations between
system GPIO <-> GPIO offset which are done in many places and
many times.
It is safe to do now because:
- gpiolib always passes GPIO offset to GPIO controller
- OMAP GPIO driver converted to use IRQ domain
This is preparation step before removing:
#define GPIO_INDEX(bank, gpio)
#define GPIO_BIT(bank, gpio)
int omap_irq_to_gpio()
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Both functions omap_set_gpio_dataout_reg() and
omap_set_gpio_dataout_mask() accept GPIO offset
as 'gpio' input parameter, so rename it to 'offset' and
drop usage of GPIO_BIT() macro.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Convert omap_gpio_is_input() to use GPIO offset instead of mask and,
in such way, make code simpler and remove few lines of code.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIOLib core implemnts irqchip->irq_request/release_resources callbacks
internally and these callbacks already contain clalls of
gpiochip_lock/unlock_as_irq().
Hence, remove unnecessary call of gpiochip_unlock_as_irq() from
omap_gpio_irq_shutdown().
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Similar to omap_gpio_irq_type() let's make sure that the GPIO
is usable as an interrupt if the platform init code did not
call gpio_request(). Otherwise we can get invalid device access
after setup_irq():
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x214/0x340()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Idle): Data Access in Supervisor mode during Functional access
...
[<c05f21e4>] (__irq_svc) from [<c05f1974>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[<c05f1974>] (_raw_spin_unlock_irqrestore) from [<c00914a8>] (__setup_irq+0x244/0x530)
[<c00914a8>] (__setup_irq) from [<c00917d4>] (setup_irq+0x40/0x8c)
[<c00917d4>] (setup_irq) from [<c0039c8c>] (omap_system_dma_probe+0x1d4/0x2b4)
[<c0039c8c>] (omap_system_dma_probe) from [<c03b2200>] (platform_drv_probe+0x44/0xa4)
...
We can fix this the same way omap_gpio_irq_type() is handling it.
Note that the long term solution is to change the gpio-omap driver
to handle the banks as separate driver instances. This will allow
us to rely on just runtime PM for tracking the bank specific state.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/gpio/gpio-omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When viewing the /proc/interrupts, there is no information about which
GPIO bank a specific gpio interrupt is hooked on to. This is more than a
bit irritating as such information can esily be provided back to the
user and at times, can be crucial for debug.
So, instead of displaying something like:
31: 0 0 GPIO 0 palmas
32: 0 0 GPIO 27 mmc0
Display the following with appropriate device name:
31: 0 0 4ae10000.gpio 0 palmas
32: 0 0 4805d000.gpio 27 mmc0
This requires that we create irq_chip instance specific for each GPIO
bank which is trivial to achieve.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.
Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO OMAP driver didn't have a consistent naming scheme for
all its functions. Some of them had an omap prefix while others
didn't. There are many advantages on having a separate namespace
for driver functions so let's add an "omap" prefix to all of them.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The <linux/irqchip/chained_irq.h> header is already included
when selecting GPIOLIB_IRQCHIP so there is no need to do it
in the driver. This is a left over from commit fb655f5
("gpio: omap: convert driver to use gpiolib irqchip").
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO irqchips assign to the cascaded IRQs their own lock class
in order to avoid warnings about lockdep recursions since that
allow the lockdep core to keep track of things.
Since commit e45d1c80 ("gpio: put GPIO IRQs into their own lock class")
there is no need to do this in a driver if it's using the GPIO
irqchip helpers since gpiolib already assigns a lockdep class.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
