summaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)Author
2020-04-02mmc: sdhci-of-at91: fix cd-gpios for SAMA5D2Michał Mirosław
commit 53dd0a7cd65edc83b0c243d1c08377c8b876b2ee upstream. SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least SAMA5D27 doesn't). Fix this by forcing card-detect in the module if module-controlled CD is not used. Fixed commit addresses the problem only for non-removable cards. This amends it to also cover gpio-cd case. Cc: stable@vger.kernel.org Fixes: 7a1e3f143176 ("mmc: sdhci-of-at91: force card detect value for non removable devices") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-14mmc: spi: Toggle SPI polarity, do not hardcode itLinus Walleij
commit af3ed119329cf9690598c5a562d95dfd128e91d6 upstream. The code in mmc_spi_initsequence() tries to send a burst with high chipselect and for this reason hardcodes the device into SPI_CS_HIGH. This is not good because the SPI_CS_HIGH flag indicates logical "asserted" CS not always the physical level. In some cases the signal is inverted in the GPIO library and in that case SPI_CS_HIGH is already set, and enforcing SPI_CS_HIGH again will actually drive it low. Instead of hard-coding this, toggle the polarity so if the default is LOW it goes high to assert chipselect but if it is already high then toggle it low instead. Cc: Phil Elwell <phil@raspberrypi.org> Reported-by: Mark Brown <broonie@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29mmc: sdhci: fix minimum clock rate for v3 controllerMichał Mirosław
commit 2a187d03352086e300daa2044051db00044cd171 upstream. For SDHCIv3+ with programmable clock mode, minimal clock frequency is still base clock / max(divider). Minimal programmable clock frequency is always greater than minimal divided clock frequency. Without this patch, SDHCI uses out-of-spec initial frequency when multiplier is big enough: mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz [for 480 MHz source clock divided by 1024] The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode. Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode") Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present Cc: <stable@vger.kernel.org> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29mmc: tegra: fix SDR50 tuning overrideMichał Mirosław
commit f571389c0b015e76f91c697c4c1700aba860d34f upstream. Commit 7ad2ed1dfcbe inadvertently mixed up a quirk flag's name and broke SDR50 tuning override. Use correct NVQUIRK_ name. Fixes: 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes") Cc: <stable@vger.kernel.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Link: https://lore.kernel.org/r/9aff1d859935e59edd81e4939e40d6c55e0b55f6.1578390388.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29mmc: sdhci-brcmstb: handle mmc_of_parse() errors during probeStefan Wahren
[ Upstream commit 1e20186e706da8446f9435f2924cd65ab1397e73 ] We need to handle mmc_of_parse() errors during probe otherwise the MMC driver could start without proper initialization (e.g. power sequence). Fixes: 476bf3d62d5c ("mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-04mmc: sdhci: Update the tuning failed messages to pr_debug levelFaiz Abbas
Tuning support in DDR50 speed mode was added in SD Specifications Part1 Physical Layer Specification v3.01. Its not possible to distinguish between v3.00 and v3.01 from the SCR and that is why since commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode") tuning failures are ignored in DDR50 speed mode. Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this error gets printed during enumeration and also if retune is triggered at any time during operation. Update the printk level to pr_debug so that these errors don't lead to false error reports. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Cc: stable@vger.kernel.org # v4.4+ Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-04mmc: sdhci-of-esdhc: fix P2020 errata handlingYangbo Lu
commit fe0acab448f68c3146235afe03fb932e242ec94c upstream. Two previous patches introduced below quirks for P2020 platforms. - SDHCI_QUIRK_RESET_AFTER_REQUEST - SDHCI_QUIRK_BROKEN_TIMEOUT_VAL The patches made a mistake to add them in quirks2 of sdhci_host structure, while they were defined for quirks. host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST; host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; This patch is to fix them. host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST; host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; Fixes: 05cb6b2a66fa ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support") Fixes: a46e42712596 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04Revert "mmc: sdhci: Fix incorrect switch to HS mode"Faiz Abbas
commit 07bcc411567cb96f9d1fc84fff8d387118a2920d upstream. This reverts commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37. This commit aims to treat SD High speed and SDR25 as the same while setting UHS Timings in HOST_CONTROL2 which leads to failures with some SD cards in AM65x. Revert this commit. The issue this commit was trying to fix can be implemented in a platform specific callback instead of common sdhci code. Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requestsEugeniu Rosca
[ Upstream commit c91843463e9e821dc3b48fe37e3155fa38299f6e ] Isolated initially to renesas_sdhi_internal_dmac [1], Ulf suggested adding MMC_CAP_ERASE to the TMIO mmc core: On Fri, Nov 15, 2019 at 10:27:25AM +0100, Ulf Hansson wrote: -- snip -- This test and due to the discussions with Wolfram and you in this thread, I would actually suggest that you enable MMC_CAP_ERASE for all tmio variants, rather than just for this particular one. In other words, set the cap in tmio_mmc_host_probe() should be fine, as it seems none of the tmio variants supports HW busy detection at this point. -- snip -- Testing on R-Car H3ULCB-KF doesn't reveal any issues (v5.4-rc7): root@rcar-gen3:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk0 179:0 0 59.2G 0 disk <--- eMMC mmcblk0boot0 179:8 0 4M 1 disk mmcblk0boot1 179:16 0 4M 1 disk mmcblk1 179:24 0 30G 0 disk <--- SD card root@rcar-gen3:~# time blkdiscard /dev/mmcblk0 real 0m8.659s user 0m0.001s sys 0m1.920s root@rcar-gen3:~# time blkdiscard /dev/mmcblk1 real 0m1.176s user 0m0.001s sys 0m0.124s [1] https://lore.kernel.org/linux-renesas-soc/20191112134808.23546-1-erosca@de.adit-jv.com/ Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com> Originally-by: Harish Jenny K N <harish_kandiga@mentor.com> Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-21mmc: host: omap_hsmmc: add code for special init of wl1251 to get rid of ↵H. Nikolaus Schaller
pandora_wl1251_init_card commit f6498b922e57aecbe3b7fa30a308d9d586c0c369 upstream. Pandora_wl1251_init_card was used to do special pdata based setup of the sdio mmc interface. This does no longer work with v4.7 and later. A fix requires a device tree based mmc3 setup. Therefore we move the special setup to omap_hsmmc.c instead of calling some pdata supplied init_card function. The new code checks for a DT child node compatible to wl1251 so it will not affect other MMC3 use cases. Generally, this code was and still is a hack and should be moved to mmc core to e.g. read such properties from optional DT child nodes. Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.7+ [Ulf: Fixed up some checkpatch complaints] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-28mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready failChaotian Jing
[ Upstream commit f38a9774ddde9d79b3487dd888edd8b8623552af ] when msdc_cmd_is_ready return fail, the req_timeout work has not been inited and cancel_delayed_work() will return false, then, the request return directly and never call mmc_request_done(). so need call mod_delayed_work() before msdc_cmd_is_ready() Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-25mmc: sdhci-of-at91: fix quirk2 overwriteEugen Hristev
commit fed23c5829ecab4ddc712d7b0046e59610ca3ba4 upstream. The quirks2 are parsed and set (e.g. from DT) before the quirk for broken HS200 is set in the driver. The driver needs to enable just this flag, not rewrite the whole quirk set. Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-05mmc: sdhci: Fix incorrect switch to HS modeAl Cooper
[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ] When switching from any MMC speed mode that requires 1.8v (HS200, HS400 and HS400ES) to High Speed (HS) mode, the system ends up configured for SDR12 with a 50MHz clock which is an illegal mode. This happens because the SDHCI_CTRL_VDD_180 bit in the SDHCI_HOST_CONTROL2 register is left set and when this bit is set, the speed mode is controlled by the SDHCI_CTRL_UHS field in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling() because there is no UHS mode being set. The fix is to change sdhci_set_uhs_signaling() to set the SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for any switch to HS mode. This was found on a new eMMC controller that does strict checking of the speed mode and the corresponding clock rate. It caused the switch to HS400 mode to fail because part of the sequence to switch to HS400 requires a switch from HS200 to HS before going to HS400. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-09-06mmc: core: Fix init of SD cards reporting an invalid VDD rangeUlf Hansson
commit 72741084d903e65e121c27bd29494d941729d4a1 upstream. The OCR register defines the supported range of VDD voltages for SD cards. However, it has turned out that some SD cards reports an invalid voltage range, for example having bit7 set. When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from the invalid VDD range, this triggers the core to run a power cycle of the card to try to initialize it at the lowest common supported voltage. Obviously this fails, since the card can't support it. Let's fix this problem, by clearing invalid bits from the read OCR register for SD cards, before proceeding with the VDD voltage negotiation. Cc: stable@vger.kernel.org Reported-by: Philip Langdale <philipl@overt.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Philip Langdale <philipl@overt.org> Tested-by: Philip Langdale <philipl@overt.org> Tested-by: Manuel Presnitz <mail@mpy.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-06mmc: sdhci-of-at91: add quirk for broken HS200Eugen Hristev
commit 7871aa60ae0086fe4626abdf5ed13eeddf306c61 upstream. HS200 is not implemented in the driver, but the controller claims it through caps. Remove it via a quirk, to make sure the mmc core do not try to enable HS200, as it causes the eMMC initialization to fail. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-06mmc: dw_mmc: Fix occasional hang after tuning on eMMCDouglas Anderson
commit ba2d139b02ba684c6c101de42fed782d6cd2b997 upstream. In commit 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") we fixed a tuning-induced hang that I saw when stress testing tuning on certain SD cards. I won't re-hash that whole commit, but the summary is that as a normal part of tuning you need to deal with transfer errors and there were cases where these transfer errors was putting my system into a bad state causing all future transfers to fail. That commit fixed handling of the transfer errors for me. In downstream Chrome OS my fix landed and had the same behavior for all SD/MMC commands. However, it looks like when the commit landed upstream we limited it to only SD tuning commands. Presumably this was to try to get around problems that Alim Akhtar reported on exynos [1]. Unfortunately while stress testing reboots (and suspend/resume) on some rk3288-based Chromebooks I found the same problem on the eMMC on some of my Chromebooks (the ones with Hynix eMMC). Since the eMMC tuning command is different (MMC_SEND_TUNING_BLOCK_HS200 vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the same situation. I'm hoping that whatever problems exynos was having in the past are somehow magically fixed now and we can make the behavior the same for all commands. [1] https://lkml.kernel.org/r/CAGOxZ53WfNbaMe0_AM0qBqU47kAfgmPBVZC8K8Y-_J3mDMqW4A@mail.gmail.com Fixes: 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Alim Akhtar <alim.akhtar@gmail.com> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-31mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 supportYinbo Zhu
[ Upstream commit 05cb6b2a66fa7837211a060878e91be5eb10cb07 ] eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock), and 0xC(2^25 SD clock). The data timeout counter can count from 2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout counter counts for only 2^13 SD clocks. A-008358: The data timeout counter value loaded into the timeout counter is less than expected and can result into early timeout error in case of eSDHC data transactions. The table below shows the expected vs actual timeout period for different values of SYSCTL[DTOCV]: these two erratum has the same quirk to control it, and set SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: sdhci-of-esdhc: add erratum eSDHC5 supportYinbo Zhu
[ Upstream commit a46e42712596b51874f04c73f1cdf1017f88df52 ] Software writing to the Transfer Type configuration register (system clock domain) can cause a setup/hold violation in the CRC flops (card clock domain), which can cause write accesses to be sent with corrupt CRC values. This issue occurs only for write preceded by read. this erratum is to fix this issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc_spi: add a status check for spi_sync_lockedKangjie Lu
[ Upstream commit 611025983b7976df0183390a63a2166411d177f1 ] In case spi_sync_locked fails, the fix reports the error and returns the error code upstream. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: core: make pwrseq_emmc (partially) support sleepy GPIO controllersAndrea Merello
[ Upstream commit 002ee28e8b322d4d4b7b83234b5d0f4ebd428eda ] pwrseq_emmc.c implements a HW reset procedure for eMMC chip by driving a GPIO line. It registers the .reset() cb on mmc_pwrseq_ops and it registers a system restart notification handler; both of them perform reset by unconditionally calling gpiod_set_value(). If the eMMC reset line is tied to a GPIO controller whose driver can sleep (i.e. I2C GPIO controller), then the kernel would spit warnings when trying to reset the eMMC chip by means of .reset() mmc_pwrseq_ops cb (that is exactly what I'm seeing during boot). Furthermore, on system reset we would gets to the system restart notification handler with disabled interrupts - local_irq_disable() is called in machine_restart() at least on ARM/ARM64 - and we would be in trouble when the GPIO driver tries to sleep (which indeed doesn't happen here, likely because in my case the machine specific code doesn't call do_kernel_restart(), I guess..). This patch fixes the .reset() cb to make use of gpiod_set_value_cansleep(), so that the eMMC gets reset on boot without complaints, while, since there isn't that much we can do, we avoid register the restart handler if the GPIO controller has a sleepy driver (and we spit a dev_notice() message to let people know).. This had been tested on a downstream 4.9 kernel with backported commit 83f37ee7ba33 ("mmc: pwrseq: Add reset callback to the struct mmc_pwrseq_ops") and commit ae60fb031cf2 ("mmc: core: Don't do eMMC HW reset when resuming the eMMC card"), because I couldn't boot my board otherwise. Maybe worth to RFT. Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: core: Verify SD bus widthRaul E Rangel
[ Upstream commit 9e4be8d03f50d1b25c38e2b59e73b194c130df7d ] The SD Physical Layer Spec says the following: Since the SD Memory Card shall support at least the two bus modes 1-bit or 4-bit width, then any SD Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101"). This change verifies the card has specified a bus width. AMD SDHC Device 7806 can get into a bad state after a card disconnect where anything transferred via the DATA lines will always result in a zero filled buffer. Currently the driver will continue without error if the HC is in this condition. A block device will be created, but reading from it will result in a zero buffer. This makes it seem like the SD device has been erased, when in actuality the data is never getting copied from the DATA lines to the data buffer. SCR is the first command in the SD initialization sequence that uses the DATA lines. By checking that the response was invalid, we can abort mounting the card. Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Raul E Rangel <rrangel@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-14x86/cpu: Sanitize FAM6_ATOM namingPeter Zijlstra
commit f2c4db1bd80720cd8cb2a5aa220d9bc9f374f04e upstream. Going primarily by: https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors with additional information gleaned from other related pages; notably: - Bonnell shrink was called Saltwell - Moorefield is the Merriefield refresh which makes it Airmont The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE for i in `git grep -l FAM6_ATOM` ; do sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \ -e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \ -e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \ -e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \ -e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \ -e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \ -e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \ -e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \ -e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \ -e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \ -e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i} done Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: dave.hansen@linux.intel.com Cc: len.brown@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> [bwh: Backported to 4.9: - Drop changes to CPU IDs that weren't already included - Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27mmc: sdhci: Fix data command CRC error handlingAdrian Hunter
[ Upstream commit 4bf780996669280171c9cd58196512849b93434e ] Existing data command CRC error handling is non-standard and does not work with some Intel host controllers. Specifically, the assumption that the host controller will continue operating normally after the error interrupt, is not valid. Change the driver to handle the error in the same manner as a data CRC error, taking care to ensure that the data line reset is done for single or multi-block transfers, and it is done before unmapping DMA. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-20mmc: davinci: remove extraneous __init annotationArnd Bergmann
[ Upstream commit 9ce58dd7d9da3ca0d7cb8c9568f1c6f4746da65a ] Building with clang finds a mistaken __init tag: WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host() The function davinci_mmcsd_probe() references the function __init init_mmcsd_host(). This is often because davinci_mmcsd_probe lacks a __init annotation or the annotation of init_mmcsd_host is wrong. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-05mmc: omap: fix the maximum timeout settingAaro Koskinen
[ Upstream commit a6327b5e57fdc679c842588c3be046c0b39cc127 ] When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy: MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! [ad inf.] Emulator warnings appear to be valid. The TI document SPRU680 [1] ("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card (MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253 cycles and "0xff and 0xfe cannot be used". Fix by using 0xfd as the maximum timeout. Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810 (OMAP2420) that MMC works as before. [1] http://www.ti.com/lit/ug/spru680/spru680.pdf Fixes: 730c9b7e6630f ("[MMC] Add OMAP MMC host driver") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-27mmc: pxamci: fix enum type confusionArnd Bergmann
commit e60a582bcde01158a64ff948fb799f21f5d31a11 upstream. clang points out several instances of mismatched types in this drivers, all coming from a single declaration: drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion] direction = DMA_DEV_TO_MEM; ~ ^~~~~~~~~~~~~~ drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion] tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction, The behavior is correct, so this must be a simply typo from dma_data_direction and dma_transfer_direction being similarly named types with a similar purpose. Fixes: 6464b7140951 ("mmc: pxamci: switch over to dmaengine use") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-19mmc: tmio_mmc_core: don't claim spurious interruptsSergei Shtylyov
commit 5c27ff5db1491a947264d6d4e4cbe43ae6535bae upstream. I have encountered an interrupt storm during the eMMC chip probing (and the chip finally didn't get detected). It turned out that U-Boot left the DMAC interrupts enabled while the Linux driver didn't use those. The SDHI driver's interrupt handler somehow assumes that, even if an SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think that if none of the enabled interrupts happened and got handled, we should return IRQ_NONE -- that way the kernel IRQ code recoginizes a spurious interrupt and masks it off pretty quickly... Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-05mmc: spi: Fix card detection during probeJonathan Neuschäfer
commit c9bd505dbd9d3dc80c496f88eafe70affdcf1ba6 upstream. When using the mmc_spi driver with a card-detect pin, I noticed that the card was not detected immediately after probe, but only after it was unplugged and plugged back in (and the CD IRQ fired). The call tree looks something like this: mmc_spi_probe mmc_add_host mmc_start_host _mmc_detect_change mmc_schedule_delayed_work(&host->detect, 0) mmc_rescan host->bus_ops->detect(host) mmc_detect _mmc_detect_card_removed host->ops->get_cd(host) mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set) mmc_gpiod_request_cd ctx->cd_gpio = desc To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ is registered. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-06mmc: sdhci-iproc: handle mmc_of_parse() errors during probeStefan Wahren
commit 2bd44dadd5bfb4135162322fd0b45a174d4ad5bf upstream. We need to handle mmc_of_parse() errors during probe. This finally fixes the wifi regression on Raspberry Pi 3 series. In error case the wifi chip was permanently in reset because of the power sequence depending on the deferred probe of the GPIO expander. Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver") Cc: stable@vger.kernel.org Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-26mmc: atmel-mci: do not assume idle after atmci_request_endJonas Danielsson
[ Upstream commit ae460c115b7aa50c9a36cf78fced07b27962c9d0 ] On our AT91SAM9260 board we use the same sdio bus for wifi and for the sd card slot. This caused the atmel-mci to give the following splat on the serial console: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44 Modules linked in: CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14 Hardware name: Atmel AT91SAM9 [<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14) [<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4) [<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24) [<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44) [<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc) [<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164) [<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0) [<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330) [<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310) [<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac) [<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118) [<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118) [<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34) ---[ end trace 594371ddfa284bd6 ]--- This is: WARN_ON(host->cmd); This was fixed on our board by letting atmci_request_end determine what state we are in. Instead of unconditionally setting it to STATE_IDLE on STATE_END_REQUEST. Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2018-12-29mmc: omap_hsmmc: fix DMA API warningRussell King
commit 0b479790684192ab7024ce6a621f93f6d0a64d92 upstream. While booting with rootfs on MMC, the following warning is encountered on OMAP4430: omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536] This is because the DMA engine has a default maximum segment size of 64K but HSMMC sets: mmc->max_blk_size = 512; /* Block Length at max can be 1024 */ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; mmc->max_seg_size = mmc->max_req_size; which ends up telling the block layer that we support a maximum segment size of 65535*512, which exceeds the advertised DMA engine capabilities. Fix this by clamping the maximum segment size to the lower of the maximum request size and of the DMA engine device used for either DMA channel. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-29mmc: core: Use a minimum 1600ms timeout when enabling CACHE ctrlUlf Hansson
commit e3ae3401aa19432ee4943eb0bbc2ec704d07d793 upstream. Some eMMCs from Micron have been reported to need ~800 ms timeout, while enabling the CACHE ctrl after running sudden power failure tests. The needed timeout is greater than what the card specifies as its generic CMD6 timeout, through the EXT_CSD register, hence the problem. Normally we would introduce a card quirk to extend the timeout for these specific Micron cards. However, due to the rather complicated debug process needed to find out the error, let's simply use a minimum timeout of 1600ms, the double of what has been reported, for all cards when enabling CACHE ctrl. Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reported-by: Andreas Dannenberg <dannenberg@ti.com> Reported-by: Faiz Abbas <faiz_abbas@ti.com> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-29mmc: core: Allow BKOPS and CACHE ctrl even if no HPI supportUlf Hansson
commit ba9f39a785a9977e72233000711ef1eb48203551 upstream. In commit 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards"), then intent was to prevent HPI from being used for some eMMC cards, which didn't properly support it. However, that went too far, as even BKOPS and CACHE ctrl became prevented. Let's restore those parts and allow BKOPS and CACHE ctrl even if HPI isn't supported. Fixes: 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards") Cc: Pratibhasagar V <pratibha@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-29mmc: core: Reset HPI enabled state during re-init and in case of errorsUlf Hansson
commit a0741ba40a009f97c019ae7541dc61c1fdf41efb upstream. During a re-initialization of the eMMC card, we may fail to re-enable HPI. In these cases, that isn't properly reflected in the card->ext_csd.hpi_en bit, as it keeps being set. This may cause following attempts to use HPI, even if's not enabled. Let's fix this! Fixes: eb0d8f135b67 ("mmc: core: support HPI send command") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-21MMC: OMAP: fix broken MMC on OMAP15XX/OMAP5910/OMAP310Aaro Koskinen
commit e8cde625bfe8a714a856e1366bcbb259d7346095 upstream. Since v2.6.22 or so there has been reports [1] about OMAP MMC being broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON") that changed clock enabling to be done on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX the hardware doesn't seem to like it and the MMC just stops responding. Fix by memorizing the power mode and do the init only when necessary. Before the patch (on Palm TE): mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SDC 977 MiB mmci-omap mmci-omap.0: command timeout (CMD18) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD12) [x 6] mmci-omap mmci-omap.0: command timeout (CMD13) [x 6] mmcblk0: error -110 requesting status mmci-omap mmci-omap.0: command timeout (CMD8) mmci-omap mmci-omap.0: command timeout (CMD18) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD12) [x 6] mmci-omap mmci-omap.0: command timeout (CMD13) [x 6] mmcblk0: error -110 requesting status mmcblk0: recovery failed! print_req_error: I/O error, dev mmcblk0, sector 0 Buffer I/O error on dev mmcblk0, logical block 0, async page read mmcblk0: unable to read partition table After the patch: mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SDC 977 MiB mmcblk0: p1 The patch is based on a fix and analysis done by Ladislav Michl. Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770) and OMAP2420 (Nokia N810). [1] https://marc.info/?t=123175197000003&r=1&w=2 Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON") Reported-by: Ladislav Michl <ladis@linux-mips.org> Reported-by: Andrzej Zaborowski <balrogg@gmail.com> Tested-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-13mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01Yu Zhao
[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ] This device reports SDHCI_CLOCK_INT_STABLE even though it's not ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 | SDHCI_CLOCK_CARD_EN but only observed the first operand). mmc1: Timeout waiting for hardware cmd interrupt. mmc1: sdhci: ============ SDHCI REGISTER DUMP =========== mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603 mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001 mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03 mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083 mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077 mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8 mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000 mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 mmc1: sdhci: Host ctl2: 0x00000008 mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000 mmc1: sdhci: ============================================ The problem happens during wakeup from S3. Adding a delay quirk after power up reliably fixes the problem. Signed-off-by: Yu Zhao <yuzhao@google.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26mmc: sdhci: do not try to use 3.3V signaling if not supportedStefan Agner
[ Upstream commit 1b5190c2e74c47ebe4bcecf7a072358ad9f1feaa ] For eMMC devices it is valid to only support 1.8V signaling. When vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V initially and prints the following warning: mmc1: Switching to 3.3V signalling voltage failed Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is not available. This prevents the stack from even trying to use 3.3V signaling and avoids the above warning. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26mmc: tegra: prevent HS200 on Tegra 3Stefan Agner
[ Upstream commit 127407e36f4fe3a1d5e8b9998b479956ce83a7dc ] The stack assumes that SDHC controller which support SD3.0 (SDR104) do support HS200. This is not the case for Tegra 3, which does support SD 3.0 but only supports eMMC spec 4.41. Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not support HS200. Note that commit 156e14b126ff ("mmc: sdhci: fix caps2 for HS200") added the tie between SD3.0 (SDR104) and HS200. I don't think that this is necessarly true. It is fully legitimate to support SD3.0 and not support HS200. The quirk naming suggests something is broken in the controller, but this is not the case: The controller simply does not support HS200. Fixes: 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes") Signed-off-by: Stefan Agner <stefan@agner.ch> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26mmc: omap_hsmmc: fix wakeirq handling on removalAndreas Kemnade
commit 3c398f3c3bef21961eaaeb93227fa66d440dc83d upstream. after unbinding mmc I get things like this: [ 185.294067] mmc1: card 0001 removed [ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13 The wakeirq stays in /proc-interrupts rebinding shows this: [ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup) [ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ [ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling That bug seems to be introduced by switching from devm_request_irq() to generic wakeirq handling. So let us cleanup at removal. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Fixes: 5b83b2234be6 ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-03mmc: pwrseq: Use kmalloc_array instead of stack VLATobin C. Harding
[ Upstream commit 486e6661367b40f927aadbed73237693396cbf94 ] The use of stack Variable Length Arrays needs to be avoided, as they can be a vector for stack exhaustion, which can be both a runtime bug (kernel Oops) or a security flaw (overwriting memory beyond the stack). Also, in general, as code evolves it is easy to lose track of how big a VLA can get. Thus, we can end up having runtime failures that are hard to debug. As part of the directive[1] to remove all VLAs from the kernel, and build with -Wvla. Currently driver is using a VLA declared using the number of descriptors. This array is used to store integer values and is later used as an argument to `gpiod_set_array_value_cansleep()` This can be avoided by using `kmalloc_array()` to allocate memory for the array of integer values. Memory is free'd before return from function. >From the code it appears that it is safe to sleep so we can use GFP_KERNEL (based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`. It can be expected that this patch will result in a small increase in overhead due to the use of `kmalloc_array()` [1] https://lkml.org/lkml/2018/3/7/621 Signed-off-by: Tobin C. Harding <me@tobin.cc> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-03mmc: dw_mmc: update actual clock for mmc debugfsShawn Lin
[ Upstream commit ff178981bd5fd1667f373098740cb1c6d6efa1ba ] Respect the actual clock for mmc debugfs to help better debug the hardware. mmc_host mmc0: Bus speed (slot 0) = 135475200Hz (slot req 150000000Hz, actual 135475200HZ div = 0) cat /sys/kernel/debug/mmc0/ios clock: 150000000 Hz actual clock: 135475200 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 9 (mmc HS200) signal voltage: 0 (1.80 V) driver type: 0 (driver type B) Cc: Xiao Yao <xiaoyao@rock-chips.com> Cc: Ziyuan <xzy.xu@rock-chips.com> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-17mmc: dw_mmc: fix card threshold control configurationx00270170
commit 7a6b9f4d601dfce8cb68f0dcfd834270280e31e6 upstream. Card write threshold control is supposed to be set since controller version 2.80a for data write in HS400 mode and data read in HS200/HS400/SDR104 mode. However the current code returns without configuring it in the case of data writing in HS400 mode. Meanwhile the patch fixes that the current code goes to 'disable' when doing data reading in HS400 mode. Fixes: 7e4bf1bc9543 ("mmc: dw_mmc: add the card write threshold for HS400 mode") Signed-off-by: Qing Xia <xiaqing17@hisilicon.com> Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30mmc: sdhci-iproc: fix 32bit writes for TRANSFER_MODE registerCorneliu Doban
commit 5f651b870485ee60f5abbbd85195a6852978894a upstream. When the host controller accepts only 32bit writes, the value of the 16bit TRANSFER_MODE register, that has the same 32bit address as the 16bit COMMAND register, needs to be saved and it will be written in a 32bit write together with the command as this will trigger the host to send the command on the SD interface. When sending the tuning command, TRANSFER_MODE is written and then sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and write it again resulting in wrong value to be written because the initial write value was saved in a shadow and the read-back returned a wrong value, from the register. Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE when a saved value exist. Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are saved for a different reason, although a scenario that will cause the mentioned problem on this registers is not probable. Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver") Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Cc: stable@vger.kernel.org # v4.1+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30mmc: sdhci-iproc: remove hard coded mmc cap 1.8vSrinath Mannam
commit 4c94238f37af87a2165c3fb491b4a8b50e90649c upstream. Remove hard coded mmc cap 1.8v from platform data as it is board specific. The 1.8v DDR mmc caps can be enabled using DTS property for those boards that support it. Fixes: b17b4ab8ce38 ("mmc: sdhci-iproc: define MMC caps in platform data") Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-24mmc: jz4740: Fix race condition in IRQ mask updateAlex Smith
commit a04f0017c22453613d5f423326b190c61e3b4f98 upstream. A spinlock is held while updating the internal copy of the IRQ mask, but not while writing it to the actual IMASK register. After the lock is released, an IRQ can occur before the IMASK register is written. If handling this IRQ causes the mask to be changed, when the handler returns back to the middle of the first mask update, a stale value will be written to the mask register. If this causes an IRQ to become unmasked that cannot have its status cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ, then we can end up stuck with the same IRQ repeatedly being fired but not handled. Normally the MMC IRQ handler attempts to clear any unexpected IRQs by writing IREG, but for those that cannot be cleared in this way then the IRQ will just repeatedly fire. This was resulting in lockups after a while of using Wi-Fi on the CI20 (GitHub issue #19). Resolve by holding the spinlock until after the IMASK register has been updated. Cc: stable@vger.kernel.org Link: https://github.com/MIPS/CI20_linux/issues/19 Fixes: 61bfbdb85687 ("MMC: Add support for the controller on JZ4740 SoCs.") Tested-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Alex Smith <alex.smith@imgtec.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13sdhci: Advertise 2.0v supply on SDIO host controllerAndy Shevchenko
[ Upstream commit 2a609abe71ca59e4bd7139e161eaca2144ae6f2e ] On Intel Edison the Broadcom Wi-Fi card, which is connected to SDIO, requires 2.0v, while the host, according to Intel Merrifield TRM, supports 1.8v supply only. The card announces itself as mmc2: new ultra high speed DDR50 SDIO card at address 0001 Introduce a custom OCR mask for SDIO host controller on Intel Merrifield and add a special case to sdhci_set_power_noreg() to override 2.0v supply by enforcing 1.8v power choice. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-28mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occursEvgeniy Didin
commit 47b7de2f6c18f75d1f2716efe752cba43f32a626 upstream. It was found that in IDMAC mode after soft-reset driver switches to PIO mode. That's what happens in case of DTO timeout overflow calculation failure: 1. soft-reset is called 2. driver restarts dma 3. descriptors states are checked, one of descriptor is owned by the IDMAC. 4. driver can't use DMA and then switches to PIO mode. Failure was already fixed in: https://www.spinics.net/lists/linux-mmc/msg48125.html. Behaviour while soft-reset is not something we except or even want to happen. So we switch from dw_mci_idmac_reset to dw_mci_idmac_init, so descriptors are cleaned before starting dma. And while at it explicitly zero des0 which otherwise might contain garbage as being allocated by dmam_alloc_coherent(). Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Cc: Shawn Lin <shawn.lin@rock-chips.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: linux-snps-arc@lists.infradead.org Cc: <stable@vger.kernel.org> # 4.4+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24mmc: avoid removing non-removable hosts during suspendDaniel Drake
[ Upstream commit de8dcc3d2c0e08e5068ee1e26fc46415c15e3637 ] The Weibu F3C MiniPC has an onboard AP6255 module, presenting two SDIO functions on a single MMC host (Bluetooth/btsdio and WiFi/brcmfmac), and the mmc layer correctly detects this as non-removable. After suspend/resume, the wifi and bluetooth interfaces disappear and do not get probed again. The conditions here are: 1. During suspend, we reach mmc_pm_notify() 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can suspend the SDIO host. However, mmc_sdio_pre_suspend() returns -ENOSYS because btsdio_driver does not have a suspend method. 3. mmc_pm_notify() proceeds to remove the card 4. Upon resume, mmc_rescan() does nothing with this host, because of the rescan_entered check which aims to only scan a non-removable device a single time (i.e. during boot). Fix the loss of functionality by detecting that we are unable to suspend a non-removable host, so avoid the forced removal in that case. The comment above this function already indicates that this code was only intended for removable devices. Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046ayangbo lu
[ Upstream commit a627f025eb0534052ff451427c16750b3530634c ] The ls1046a datasheet specified that the max SD clock frequency for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet specified it's 125MHz for ls1012a. So this patch is to add the limitation. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24mmc: host: omap_hsmmc: checking for NULL instead of IS_ERR()Dan Carpenter
[ Upstream commit ec5ab8933772c87f24ad62a4a602fe8949f423c2 ] devm_pinctrl_get() returns error pointers, it never returns NULL. Fixes: 455e5cd6f736 ("mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-10 20:40:32 +0000