summaryrefslogtreecommitdiff
path: root/drivers/mtd/chips/cfi_cmdset_0002.c
AgeCommit message (Collapse)Author
2019-10-01mtd: cfi_cmdset_0002: Use chip_good() to retry in do_write_oneword()Tokunori Ikegami
commit 37c673ade35c707d50583b5b25091ff8ebdeafd7 upstream. As reported by the OpenWRT team, write requests sometimes fail on some platforms. Currently to check the state chip_ready() is used correctly as described by the flash memory S29GL256P11TFI01 datasheet. Also chip_good() is used to check if the write is succeeded and it was implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error checking"). But actually the write failure is caused on some platforms and also it can be fixed by using chip_good() to check the state and retry instead. Also it seems that it is caused after repeated about 1,000 times to retry the write one word with the reset command. By using chip_good() to check the state to be done it can be reduced the retry with reset. It is depended on the actual flash chip behavior so the root cause is unknown. Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Reported-by: Fabio Bettoni <fbettoni@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com> [vigneshr@ti.com: Fix a checkpatch warning] Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-27mtd: cfi_cmdset_0002: Add support for polling status registerVignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set (0x0002) for flash operations, therefore drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation. Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register. Add support for polling Status Register to know device ready/status of erase/write operations when DQ polling is not supported. Print error messages on erase/program failure by looking at related Status Register bits. [1] https://www.cypress.com/file/213346/download Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-06-27mtd: cfi_cmdset_0002: dynamically determine the max sectorsChris Packham
Because PPB unlocking unlocks the whole chip cfi_ppb_unlock() needs to remember the locked status for each sector so it can re-lock the unaddressed sectors. Dynamically calculate the maximum number of sectors rather than using a hardcoded value that is too small for larger chips. Tested with Spansion S29GL01GS11TFI flash device. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-05-06mtd: cfi_cmdset_0002: Mark expected switch fall-throughsGustavo A. R. Silva
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. This patch fixes the following warnings: drivers/mtd/chips/cfi_cmdset_0002.c: In function ‘get_chip’: drivers/mtd/chips/cfi_cmdset_0002.c:870:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (mode == FL_READY && chip->oldstate == FL_READY) ^ drivers/mtd/chips/cfi_cmdset_0002.c:873:2: note: here default: ^~~~~~~ drivers/mtd/chips/cfi_cmdset_0002.c: In function ‘cfi_amdstd_sync’: drivers/mtd/chips/cfi_cmdset_0002.c:2745:16: warning: this statement may fall through [-Wimplicit-fallthrough=] chip->state = FL_SYNCING; ~~~~~~~~~~~~^~~~~~~~~~~~ drivers/mtd/chips/cfi_cmdset_0002.c:2750:3: note: here case FL_SYNCING: ^~~~ Warning level 3 was used: -Wimplicit-fallthrough=3 This patch is part of the ongoing efforts to enabling -Wimplicit-fallthrough. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2019-04-05mtd: cfi: fix deadloop in cfi_cmdset_0002.c do_write_bufferLiu Jian
In function do_write_buffer(), in the for loop, there is a case chip_ready() returns 1 while chip_good() returns 0, so it never break the loop. To fix this, chip_good() is enough and it should timeout if it stay bad for a while. Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value") Signed-off-by: Yi Huaijie <yihuaijie@huawei.com> Signed-off-by: Liu Jian <liujian56@huawei.com> Reviewed-by: Tokunori Ikegami <ikegami_to@yahoo.co.jp> Signed-off-by: Richard Weinberger <richard@nod.at>
2018-08-11Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/nextBoris Brezillon
Pull NAND updates from Miquel Raynal: " NAND core changes: - Add the SPI-NAND framework. - Create a helper to find the best ECC configuration. - Create NAND controller operations. - Allocate dynamically ONFI parameters structure. - Add defines for ONFI version bits. - Add manufacturer fixup for ONFI parameter page. - Add an option to specify NAND chip as a boot device. - Add Reed-Solomon error correction algorithm. - Better name for the controller structure. - Remove unused caller_is_module() definition. - Make subop helpers return unsigned values. - Expose _notsupp() helpers for raw page accessors. - Add default values for dynamic timings. - Kill the chip->scan_bbt() hook. - Rename nand_default_bbt() into nand_create_bbt(). - Start to clean the nand_chip structure. - Remove stale prototype from rawnand.h. Raw NAND controllers drivers changes: - Qcom: structuring cleanup. - Denali: use core helper to find the best ECC configuration. - Possible build of almost all drivers by adding a dependency on COMPILE_TEST for almost all of them in Kconfig, implies various fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even changes in sparc64 and ia64 architectures. - Clean the ->probe() functions error path of a lot of drivers. - Migrate all drivers to use nand_scan() instead of nand_scan_ident()/nand_scan_tail() pair. - Use mtd_device_register() where applicable to simplify the code. - Marvell: * Handle on-die ECC. * Better clocks handling. * Remove bogus comment. * Add suspend and resume support. - Tegra: add NAND controller driver. - Atmel: * Add module param to avoid using dma. * Drop Wenyou Yang from MAINTAINERS. - Denali: optimize timings handling. - FSMC: Stop using chip->read_buf(). - FSL: * Switch to SPDX license tag identifiers. * Fix qualifiers in MXC init functions. Raw NAND chip drivers changes: - Micron: * Add fixup for ONFI revision. * Update ecc_stats.corrected. * Make ECC activation stateful. * Avoid enabling/disabling ECC when it can't be disabled. * Get the actual number of bitflips. * Allow forced on-die ECC. * Support 8/512 on-die ECC. * Fix on-die ECC detection logic. - Hynix: * Fix decoding the OOB size on H27UCG8T2BTR. * Use ->exec_op() in hynix_nand_reg_write_op(). "
2018-07-07mtd: cfi: cmdset_0002: remove redundant variable timeoColin Ian King
Variable is_local is being assigned but is never used hence it is redundant and can be removed. Cleans up clang warning: warning: variable 'timeo' set but not used [-Wunused-but-set-variable] Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-22mtd: cfi_cmdset_0002: Avoid walking all chips when unlocking.Joakim Tjernlund
cfi_ppb_unlock() walks all flash chips when unlocking sectors, avoid walking chips unaffected by the unlock operation. Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-22mtd: cfi_cmdset_0002: Fix unlocking requests crossing a chip boudaryJoakim Tjernlund
The "sector is in requested range" test used to determine whether sectors should be re-locked or not is done on a variable that is reset everytime we cross a chip boundary, which can lead to some blocks being re-locked while the caller expect them to be unlocked. Fix the check to make sure this cannot happen. Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-22mtd: cfi_cmdset_0002: fix SEGV unlocking multiple chipsJoakim Tjernlund
cfi_ppb_unlock() tries to relock all sectors that were locked before unlocking the whole chip. This locking used the chip start address + the FULL offset from the first flash chip, thereby forming an illegal address. Fix that by using the chip offset(adr). Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-22mtd: cfi_cmdset_0002: Use right chip in do_ppb_xxlock()Joakim Tjernlund
do_ppb_xxlock() fails to add chip->start when querying for lock status (and chip_ready test), which caused false status reports. Fix that by adding adr += chip->start and adjust call sites accordingly. Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12treewide: kmalloc() -> kmalloc_array()Kees Cook
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-08Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD updates from Boris Brezillon: "Core changes: - Add a sysfs attribute to expose available OOB size Driver changes: - Remove HAS_DMA dependency on various drivers - Use dev_get_drvdata() instead of platform_get_drvdata() in docg3 - Replace msleep by usleep_range() in the dataflash driver - Avoid VLA usage in nftl layers - Remove useless .owner assignment in pismo - Fix various issues in the CFI driver - Improve TRX partition handling expose a DT compat for this part parser - Clarify OFFSET_CONTINUOUS meaning NAND core changes: - Add Miquel as a NAND maintainer - Add access mode to the nand_page_io_req struct - Fix kernel-doc in rawnand.h - Support bit-wise majority to recover from corrupted ONFI parameter pages - Stop checking FAIL bit after a SET_FEATURES, as documented in the ONFI spec Raw NAND Driver changes: - Fix and cleanup the error path of many NAND controller drivers - GPMI: + Cleanup/simplification of a few aspects in the driver + Take ECC setup specified in the DT into account - sunxi: remove support for GPIO-based R/B polling - MTK: + Use of_device_get_match_data() instead of of_match_device() + Add an entry in MAINTAINERS for this driver + Fix nand-ecc-step-size and nand-ecc-strength description in the DT bindings doc - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page OneNAND driver changes: - samsung: use dev_get_drvdata() instead of platform_get_drvdata() SPI NOR core changes: - Add support for a bunch of SPI NOR chips - Clear EAR reg when switching to 3-byte addressing mode on Winbond chips SPI NOR controller driver changes: - cadence: Add DMA support for direct mode reads - hisi: Prefix a few functions with hisi_ - intel: + Mark the driver as "dangerous" in Kconfig + Fix atomic sequence handling + Pass a 40us delay (instead of 0us) to readl_poll_timeout() - fsl: + fix a typo in a function name + add support for IP variants embedded in the ls2080a and ls1080a SoCs - stm32: request exclusive control of the reset line" * tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits) mtd: nand: Pass mode information to nand_page_io_req mtd: cfi_cmdset_0002: Change erase one block to enable XIP once mtd: cfi_cmdset_0002: Change erase functions to check chip good only mtd: cfi_cmdset_0002: Change erase functions to retry for error mtd: cfi_cmdset_0002: Change definition naming to retry write operation mtd: cfi_cmdset_0002: Change write buffer to check correct value mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS mtd: bcm47xxpart: add of_match_table with a new DT binding dt-bindings: mtd: document Broadcom's BCM47xx partitions mtd: spi-nor: Add support for EN25QH32 mtd: spi-nor: Add support for is25wp series chips mtd: spi-nor: Add Winbond w25q32jv support mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control mtd: spi-nor: intel: provide a range for poll_timout mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig mtd: spi-nor: intel-spi: Fix atomic sequence handling mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op mtd: rawnand: use bit-wise majority to recover the ONFI param page ...
2018-05-30mtd: cfi_cmdset_0002: Change erase one block to enable XIP onceTokunori Ikegami
To enable XIP it is executed both normal and error cases. This call can be moved after the for loop as same with erase chip. Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-30mtd: cfi_cmdset_0002: Change erase functions to check chip good onlyTokunori Ikegami
Currently the functions use to check both chip ready and good. But the chip ready is not enough to check the operation status. So change this to check the chip good instead of this. About the retry functions to make sure the error handling remain it. Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-30mtd: cfi_cmdset_0002: Change erase functions to retry for errorTokunori Ikegami
For the word write functions it is retried for error. But it is not implemented to retry for the erase functions. To make sure for the erase functions change to retry as same. This is needed to prevent the flash erase error caused only once. It was caused by the error case of chip_good() in the do_erase_oneblock(). Also it was confirmed on the MACRONIX flash device MX29GL512FHT2I-11G. But the error issue behavior is not able to reproduce at this moment. The flash controller is parallel Flash interface integrated on BCM53003. Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-30mtd: cfi_cmdset_0002: Change definition naming to retry write operationTokunori Ikegami
The definition can be used for other program and erase operations also. So change the naming to MAX_RETRIES from MAX_WORD_RETRIES. Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-30mtd: cfi_cmdset_0002: Change write buffer to check correct valueTokunori Ikegami
For the word write it is checked if the chip has the correct value. But it is not checked for the write buffer as only checked if ready. To make sure for the write buffer change to check the value. It is enough as this patch is only checking the last written word. Since it is described by data sheets to check the operation status. Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-12mtd: cfi_cmdset_0002: Fix coding style issuesTokunori Ikegami
This patch fixes mainly to remove unneeded spaces after '(' and before ')'. Also some indentation errors are fixed. Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-04-24mtd: cfi: cmdset_0002: Do not allow read/write to suspend erase block.Joakim Tjernlund
Currently it is possible to read and/or write to suspend EB's. Writing /dev/mtdX or /dev/mtdblockX from several processes may break the flash state machine. Taken from cfi_cmdset_0001 driver. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Cc: <stable@vger.kernel.org> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-21mtd: Stop updating erase_info->state and calling mtd_erase_callback()Boris Brezillon
MTD users are no longer checking erase_info->state to determine if the erase operation failed or succeeded. Moreover, mtd_erase_callback() is now a NOP. We can safely get rid of all mtd_erase_callback() calls and all erase_info->state assignments. While at it, get rid of the erase_info->state field, all MTD_ERASE_XXX definitions and the mtd_erase_callback() function. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Richard Weinberger <richard@nod.at> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Bert Kenward <bkenward@solarflare.com> --- Changes in v2: - Address a few coding style issues (reported by Miquel) - Remove comments that are no longer valid (reported by Miquel)
2017-04-19drivers/mtd: Convert remaining uses of pr_warning to pr_warnJoe Perches
To enable eventual removal of pr_warning This makes pr_warn use consistent for drivers/mtd Prior to this patch, there were 7 uses of pr_warning and 31 uses of pr_warn in drivers/mtd Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-12-18mtd: cfi_cmdset_0002: use swap() in cfi_cmdset_0002()Fabian Frederick
Use kernel.h macro definition. Thanks to Julia Lawall for Coccinelle scripting support. Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-05-27mtd: cfi_cmdset_0002: Initialize datum before calling map_word_load_partialChristian Riesch
In do_otp_write we must initialize the variable datum before calling map_word_load_partial. Otherwise the upper bits of datum may be undefined, which later causes problems in chip_good called by do_write_oneword. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-08-19Merge l2-mtd/next into l2-mtd/masterBrian Norris
2014-08-19mtd: cfi_cmdset_0002: allow retry/timeout loop to exitBrian Norris
The variable 'retries' is never modified, so if the reset operation never is going to complete, we'll get stuck in an infinite loop. It looks like the intention was to decrement 'retries' on every loop. Untested. Caught by Coverity. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-08-15mtd: cfi_cmdset_0002: check return code for get_chip()Brian Norris
Coverity CID 1230633 Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Christian Riesch <christian.riesch@omicron.at>
2014-07-16mtd: cfi_cmdset_0002: fix do_write_buffer() timeout errorBean Huo
For some NOR flashes, the size of the buffer program has been increased from 256 bytes to 512 bytes, and so 2ms maximum timeout can may not be sufficient for all different vendor's NOR flash. There is maximum timeout information in the CFI area, so we instead of picking a fixed value, we can calculate this according to the standard CFI parameters parsed at probe time. If we haven't probed this information, or it is smaller than 2000us, then specify a minimum value 2000us. Tested with Micron JS28F512M29EWx and Micron MT28EW512ABA flash devices. Signed-off-by: Bean Huo <beanhuo@outlook.com> [Brian: fix up comments, use 'max()'] Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-07-11mtd: cfi_cmdset_0002: Add support for locking OTP memoryChristian Riesch
This patch adds support for the locking of the one time programmable (OTP) memory of Micron M29EW devices. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-07-11mtd: cfi_cmdset_0002: Add support for writing OTP memoryChristian Riesch
This patch adds support for writing the one time programmable (OTP) memory of Micron M29EW devices. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-07-11mtd: cfi_cmdset_0002: Invalidate cache after entering/exiting OTP memoryChristian Riesch
When the one time programmable (OTP) memory region is entered by issuing the 0xaa/0x55/0x88 command, the OTP memory occupies the addresses which are normally used by the first sector of the regular flash memory. This patch therefore invalidates cache for this addresses after entering/exiting OTP memory. This patch also moves the code into separate functions. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-07-11mtd: cfi_cmdset_0002: Add support for reading OTPChristian Riesch
The Micron M29EW has a 256 byte one time programmable (OTP) memory. This patch adds support for reading this memory. This support will be extended for locking and writing in subsequent patches. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-03-10mtd: cfi: Remove unnecessary OOM messagesJingoo Han
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-03-10mtd: delete non-required instances of include <linux/init.h>Paul Gortmaker
None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: linux-mtd@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> [Brian: dropped one incorrect hunk] Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2013-08-05mtd: cfi_cmdset_0002: print @adr when write timeout occursHuang Shijie
Print out the @adr when the write timeout occurs. This is useful to check if the write timeouts occur at the same address. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-02-04mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) lockingStefan Roese
Currently cfi_cmdset_0002.c does not support PPB locking of sectors. This patch adds support for this locking/unlocking mechanism. It is needed on some platforms, since newer U-Boot versions do support this PPB locking and protect for example their environment sector(s) this way. This PPB locking/unlocking will be enabled for all devices supported by cfi_cmdset_0002 reporting 8 in the CFI word 0x49 (Sector Protect/Unprotect scheme). Please note that PPB locking does support sector-by-sector locking. But the whole chip can only be unlocked together. So unlocking one sector will automatically unlock all sectors of this device. Because of this chip limitation, the PPB unlocking function saves the current locking status of all sectors before unlocking the whole device. After unlocking the saved locking status is re-configured. This way only the addressed sectors will be unlocked. To selectively enable this advanced sector protection mechanism, the device-tree property "use-advanced-sector-protection" has been created. To enable support for this locking this property needs to be present in the flash DT node. E.g.: nor_flash@0,0 { compatible = "amd,s29gl256n", "cfi-flash"; bank-width = <2>; use-advanced-sector-protection; ... Tested with Spansion S29GL512S10THI and Micron JS28F512M29EWx flash devices. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-12-03mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.cHarald Nordgard-Hansen
When working on a problem with some flash chips that lock up during write-buffer operations, I think there may be a bug in the linux handling of chips using cfi_cmdset_0002.c. The datasheets I have found for a number of these chips all specify that when aborting a write-buffer command, it is not enough to use the standard reset. Rather a "write-to-buffer-reset command" is needed. This command is quite similar for all chips, the main variance seem to be if the final 0xF0 can go to any address or must go to addr_unlock1. The bug is then in the recovery handling when timing out at the end of do_write_buffer, where using the normal reset command is not sufficient. Without this change, if the write-buffer command fails then any following operations on the flash also fail. Signed-off-by: Harald Nordgard-Hansen <hhansen@pvv.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-07-16mtd: cfi_cmdset_0002: Micron M29EW bugfixes as per TN-13-07Gerlando Falauto
Fix the following issues with Micron's (formerly Numonyx) M29EW NOR flash chips, as documented on TN-13-07: - Correcting Erase Suspend Hang Ups (page 20) - Resolving the Delay After Resume Issue (page 22) Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: cfi_cmdset_0002: Slight cleanup of fixup messagesDavid Woodhouse
These should be semicolons, not commas. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: add fixup for S29NS512P NOR flash.Javier Martin
Spansion S29NS512P flash uses a 16bit transfer to report number of sectors instead of two 8bit accesses as CFI specifies. Artem: remove warning message which said that we are applying the fixup - no need to scary the user unnecessarily. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: chips: cfi_cmdset_0002: Match ENABLE_VPP()/DISABLE_VPP() callsPaul Parsons
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch ensures that only those flash operations which call ENABLE_VPP() can then call DISABLE_VPP(). Other operations should never call DISABLE_VPP(). Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: move zero length verification to MTD API functionsArtem Bityutskiy
In many places in drivers we verify for the zero length, but this is very inconsistent across drivers. This is obviously the right thing to do, though. This patch moves the check to the MTD API functions instead and removes a lot of duplication. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: remove retlen zeroing duplicationArtem Bityutskiy
The MTD API function now zero the 'retlen' parameter before calling the driver's method — do not do this again in drivers. This removes duplicated '*retlen = 0' assignent from the following methods: 'mtd_point()' 'mtd_read()' 'mtd_write()' 'mtd_writev()' 'mtd_panic_write()' Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: add leading underscore to all mtd functionsArtem Bityutskiy
This patch renames all MTD functions by adding a "_" prefix: mtd->erase -> mtd->_erase mtd->read_oob -> mtd->_read_oob ... The reason is that we are re-working the MTD API and from now on it is an error to use MTD function pointers directly - we have a corresponding API call for every pointer. By adding a leading "_" we achieve the following: 1. Make sure we convert every direct pointer users 2. A leading "_" suggests that this interface is internal and it becomes less likely that people will use them directly 3. Make sure all the out-of-tree modules stop compiling and the owners spot the big API change and amend them. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: cfi: AMD/Fujitsu compatibles: add panic write supportIra W. Snyder
This allows the mtdoops driver to work on flash chips using the AMD/Fujitsu compatible command set. As the code comments note, the locks used throughout the normal code paths in the driver are ignored, so that the chance of writing out the kernel's last messages are maximized. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-09-11mtd: cleanup style on pr_debug messagesBrian Norris
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11mtd: replace DEBUG() with pr_debug()Brian Norris
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic debugging feature is a generic kernel feature that provides more flexibility. (See Documentation/dynamic-debug-howto.txt) Also fix some punctuation, indentation, and capitalization that went along with the affected lines. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-05-25mtd: remove duplicate assignment of chip->stateTadashi Abe
This is a trivial patch which removes unnecessary assignment of chip->state in put_chip(). It's duplicated. Signed-off-by: Tadashi Abe <tabe@mvista.com> Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: fix hang-up in cfi erase and read contentionTadashi Abe
cfi erase command hangs up when erase and read contention occurs. If read runs at the same address as erase operation, read issues Erase-Suspend via get_chip() and the erase goes into sleep in wait queue. But in this case, read operation exits by time-out without waking it up. I think the other variants (0001, 0020 and lpddr) have the same problem too. Tested and verified the patch only on CFI-0002 flash, though. Signed-off-by: Tadashi Abe <tabe@mvista.com> Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-25 11:23:59 +0000