| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 6ccf50d4d4741e064ba35511a95402c63bbe21a8 ]
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 23d775f12dcd23d052a4927195f15e970e27ab26 ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e70c ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3c27f3d53d588618d81d30d6712459a3cc9489b8 ]
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6686317855c6997671982d4489ccdd946f644957 ]
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775621 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7bcad0f0e6fbc1d613e49e0ee35c8e5f2e685bb0 ]
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02ded5a173619b11728b8bf75a3fd995a2c1ff28 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 585d42bb57bb358d48906660a8de273b078810b1 ]
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 11527f3c4725640e6c40a2b7654e303f45e82a6c upstream.
Commit 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
introduced wrong .stats_set_histogram() method for Topaz family.
The Peridot method should be used instead.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3709488790022c85720f991bff50d48ed5a36e6a upstream.
Commit 9e5baf9b36367 ("net: dsa: mv88e6xxx: add RMU disable op")
introduced .rmu_disable() method with implementation for several models,
but forgot to add Topaz, which can use the Peridot implementation.
Use the Peridot implementation of .rmu_disable() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 9e5baf9b36367 ("net: dsa: mv88e6xxx: add RMU disable op")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7da467d82d1ed4fb317aff836f99709169e73f10 upstream.
Commit f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
introduced .port_set_policy() method with implementation for several
models, but forgot to add Topaz, which can use the 6352 implementation.
Use the 6352 implementation of .port_set_policy() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1fe976d308acb6374c899a4ee8025a0a016e453e upstream.
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f72f2fb8fb6be095b98af5d740ac50cffd0b0cae upstream.
Having multiple destination ports for a unicast address does not make
sense.
Make port_db_load_purge override existent unicast portvec instead of
adding a new port bit.
Fixes: 884729399260 ("net: dsa: mv88e6xxx: handle multiple ports in ATU")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210130134334.10243-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87fe04367d842c4d97a77303242d4dd4ac351e46 upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes: 92307069a96c (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a3dcb3e7e70c72a68a79b30fc3a3adad5612731c ]
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92307069a96c07d9b6e74b96b79390e7cd7d2111 ]
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0f3c66a3c7b4e8b9f654b3c998e9674376a51b0f ]
The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f4366660d65 only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.
Fixes: 5f4366660d65 ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0395823b8d9a4d87bd1bf74359123461c2ae801b ]
If the switch is not hardware reset on a warm boot, interrupts can be
left enabled, and possibly pending. This will cause us to enter an
infinite loop trying to service an interrupt we are unable to handle,
thereby preventing the kernel from booting.
Ensure that the global 2 interrupt sources are disabled before we claim
the parent interrupt.
Observed on the ZII development revision B and C platforms with
reworked serdes support, and using reboot -f to reboot the platform.
Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f7a48b68abd9b20ce1ac6298aaaa3c4d158271dd ]
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e8 ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d8dc2c9676e614ef62f54a155b50076888c8a29a ]
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a676 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the mv88e6xxx PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
For the record, the semantics of this driver are:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp rising edge
Cc: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure
a port's Layer 2 Policy Control List (PCL) via ethtool.
Currently only dropping frames based on MAC Destination or Source
Address (including the option VLAN parameter) is supported.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .port_set_policy operation to configure a port's
Policy Control List, based on mapping such as DA, SA, Etype and so on.
Models similar to 88E6352 and 88E6390 are supported at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell has different values for the state of a MAC address,
depending on its multicast bit. This patch completes the definitions
for these states.
At the same time, use 0 which is intuitive enough and simplifies the
code a bit, instead of the UC or MC unused value.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6352_serdes_power_set helper is only used at one place, in
mv88e6352_serdes_power. Keep it simple and merge the two functions
together.
Use mv88e6xxx_serdes_get_lane instead of mv88e6352_port_has_serdes
to avoid moving code. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.
As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now mv88e6xxx does not enable its ports at setup itself and let
the DSA core handle this, unused ports are disabled without being
powered on first. While that is expected, the SERDES powering code
was assuming that a port was already set up before powering it down,
resulting in freeing an unused IRQ. The patch fixes this assumption.
Fixes: b759f528ca3d ("net: dsa: mv88e6xxx: enable SERDES after setup")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a follow-up patch for commit 7a3007d22e8d ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").
Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a follow-up patch for commit 17deaf5cb37a ("net: dsa:
mv88e6xxx: create serdes_get_lane chip operation").
The .serdes_get_lane implementations access the CMODE of a port,
even though it is cached at the moment, it is safer to call them
after the mutex is locked, not before.
At the same time, check for an eventual error and return IRQ_DONE,
instead of blindly ignoring it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that mv88e6xxx_serdes_power is only called after driver setup,
we can wrap the SERDES IRQ code directly within it for clarity.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SERDES is powered on for CPU and DSA ports and powered down for unused
ports at setup time. But now that DSA calls mv88e6xxx_port_enable
and mv88e6xxx_port_disable for all ports, the SERDES power can now
be handled after setup inconditionally for all ports.
Using the port enable and disable callbacks also have the benefit to
handle the SERDES IRQ for non user ports as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disabling a port, that is not for the driver to decide what to
do with the STP state. This is already handled by the DSA layer.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.
Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).
In this check it only looks if the triplet [link, speed, duplex] is
being changed.
This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.
In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.
In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx_smi_direct_wait routine is used to wait on indirect
registers access. It is of no exception and must delay between read
attempts, like other wait routines.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
