| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit de77a53c2d1e8fb3621e63e8e1f0f0c9a1a99ff7 ]
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
User space can remove the P2P management interface while it is active
(for example, while listen/search is active) and this can cause
a crash. Ensure the P2P device is fully stopped before removing.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Connect can take longer than current timeout in some scenarios,
for example with long-range antenna array. Increase the timeout
to support these scenarios.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Set wowlan to indicate that 11ad device can wake-up
on any trigger and disconnect.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New FW supports reporting RSSI signal in dBm.
Report RSSI to kernel in case FW has this capability.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Validate buffer length has the minimum needed size
when sending management frame to protect against
possible buffer overrun.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Set resetting flag early when stopping AP to avoid
disconnect events as a result of disconnect command
sent during AP stop procedure.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Added vendor commands for low level control over
RF sectors. It allows user space a fine-grained control
over RF characteristics for TX and RX, such as direction
and gain of TX/RX. Main usages are debugging and diagnostics,
but also operational use cases.
API includes getting/setting a specific RF sector
configuration, as well as getting/setting the selected
sector which is used to communicate with a station.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Driver always invoke cfg80211_disconnected() with locally_generated as
false.
Fix this by reporting true whenever the disconnect is triggered from
upper layers (cfg80211) or from within the driver itself (reset,
deinit).
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In a fast disconnect/connect sequence, cfg80211_connect_result() can
fail to find the bss object which the driver is connecting to. Detailed
sequence of events:
* Driver is connected in STA mode
* Disconnect request arrives from user space. Driver disconnects and
calls cfg80211_disconnected() which adds new event to the
cfg80211_wq worker thread
* Connect request arrives from user space. cfg80211_connect() stores
ssid/ssid_len and calls rdev_connect()
* __cfg80211_disconnected() runs in worker thread and zero
wdev->ssid_len
* Connect succeeds. Driver calls cfg80211_connect_result() which fails
to find the bss because wdev->ssid_len is zero
To overcome this, upon connect request, store the bss object in the
driver and upon connect completion pass it to kernel using
cfg80211_connect_bss().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some dynamic debug printouts in driver are using print_hex_dump_bytes.
However, with dynamic debug disabled, print_hex_dump_bytes outputs to
log unconditionally.
Use print_hex_dump_debug instead to prevent log pollution when dynamic
debug disabled.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The driver uses the bus_request platform operation to
request resources from the platform for a specific bandwidth.
Currently the driver requests resources for the maximum
theoretical bandwidth, when interface is brought up.
Refine this process a bit: now the driver will request a
small amount of resources when interface is up, and will only
issue the maximum request when connected.
This mechanism will be improved further in the future to make
more refined requests based on actual bandwidth.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The driver should not allow starting any type of scan on a stopped
P2P device. Current implementation only checked social scan.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This function contains the HT calculations, which makes no
sense - split that out into a separate function. As a side
effect, this makes the 60G flag independent from HT_MCS so
remove the MCS one from wil6210 (also deleting a duplicate
assignment.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This now declares a module parameter, so include the necessary
header file for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Symbolic permissions are no longer recommended.
This patch changes the symbolic permissions in wil6210 driver
to octal permissions.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently we do not have full support for broadcast from
a station inside a PBSS network.
We have a workaround where instead of broadcast we do a
unicast to every known station in the PBSS.
This workaround was performed only for P2P clients.
This fix will perform the broadcast workaround also for a
regular station inside a PBSS.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
__func__ is automatically added to printouts by dynamic debug
mechanism and by wil_info/wil_err macros.
Remove __func__ from debug printouts to avoid duplication.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
By default, AP SME is handled by driver/FW.
In case disable_ap_sme is true, driver doesn't turn-on
WIPHY_FLAG_HAVE_AP_SME and the responsibility for
AP SME is passed to user space.
With AP SME disabled, driver reports assoc request frame
to user space which is then responsible for sending assoc
response frame and for sending NL80211_CMD_NEW_STATION.
Driver also reports disassoc frame to user space
which should then send NL80211_CMD_DEL_STATION.
NL80211_CMD_SET_STATION with NL80211_STA_FLAG_AUTHORIZED
is used by user space to allow/disallow data transmit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
cfg80211_ops structures are only passed as an argument to the function
wiphy_new. This argument is of type const, so cfg80211_ops strutures
having this property can be declared as const.
Done using Coccinelle
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct cfg80211_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
wiphy_new(&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct cfg80211_ops i;
File size before:
text data bss dec hex filename
18133 6632 0 24765 60bd wireless/ath/wil6210/cfg80211.o
File size after:
text data bss dec hex filename
18933 5832 0 24765 60bd wireless/ath/wil6210/cfg80211.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add support for setting retry limit for short frames,
using NL80211_CMD_SET_WIPHY with the attribute
NL80211_ATTR_WIPHY_RETRY_SHORT.
Update wiphy->retry_short from the FW default when interface
is brought up.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Implement cfg80211 abort_scan op to allow the upper layer to
abort an ongoing scan request.
In addition, notify wil6210 device on scan abort request instead
of just ignoring the scan response.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New power management wmi commands provide the ability to change
the device power save profile (enable / disable power save).
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently the places that check wil->scan_request and
call cfg80211_scan_done are not consistently protected,
so there is a risk that cfg80211_scan_done will be called
with NULL scan_request, causing a kernel crash.
Fix this by using p2p_wdev_mutex in few other places
that access scan_request. This makes sense since
scan_request may point to p2p_wdev, and it is not worth
the extra complexity of adding a new mutex.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently wiphy structure is initialized and registered
in wil_if_alloc, before some information is available such
as MAC address and capabilities. As a result there is a
small chance user space will get incorrect information
from calls such as NL80211_CMD_GET_WIPHY.
Fix this by seperating the registration and moving it
to wil_if_add which is executed later, after all
relevant information is known.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
fix stop p2p device handling to identify between search
and listen and update the upper layers with the appropriate
notification.
The stop of p2p radio operations also needs to be performed
in __wil_down.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
According to the spec the PN should be calculated per TID.
In the current implementation, the PN and key_set were set
only for TID 0, therefore only traffic for TID 0 was supported.
In order to support all TIDs, the key_set and PN should be set
for all the TIDs.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The nl80211 layer expects P2P search operation to be aborted
if needed when stopping P2P device. If the P2P search operation
is still running after returning from stop_p2p_device
it causes a WARN_ON and possibly a kernel crash.
Fix this by aborting the P2P search in wil_cfg80211_stop_p2p_device
and preventing P2P search from being started on a stopped P2P
device.
Note, the fix does not cover the case where a regular scan
is started on the P2P device. It will be completed in the
future when support is added for aborting a scan operation.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
P2P search can only run on the social channel (channel 2).
When issuing a scan request on the P2P_DEVICE interface,
driver ignored the channels argument and always performed a P2P
search.
Fix this by checking the channels argument, if it is
not specified (meaning full scan) or if a non-social channel
was specified, perform a regular scan and not a P2P search.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When starting a PCP, pass the is_go flag to firmware in
wmi_pcp_start. This flag indicates whether we started
a PCP which is also a GO(P2P group owner) or just a regular
PCP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When FW crashed with no_fw_recovery mode enabled, user space
could still call wil_cfg80211_change_iface quickly to change
interface type, and this would cause recovery to proceed and
FW crash logs may be lost.
Fix this problem by not resetting the FW in case no_fw_recovery
is enabled.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix 2 race conditions found during test runs of P2P discovery:
1. Because wil_p2p_cancel_listen was not protected, user space
could start a new P2P listen/search before wmi_stop_discovery
completed. This caused a crash in the firmware.
2. In P2P listen, when listen timer expires and user space calls
cancel_remain_on_channel at the same time, code could send the
cfg80211_remain_on_channel_expired notification twice.
Added protections with wil->mutex to several places that call
wmi_stop_discovery.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Added support for the P2P_DEVICE virtual interface. This interface
is intended for P2P management operations such as discovery and
GO negotiation. Normally it is implemented by drivers to allow
a separate interface for P2P management with its own MAC address,
but for 11ad drivers it is needed to support P2P search, since it
cannot otherwise be separated from normal scan.
Since we only support a single interface/MAC address, we can't
easily separate between primary and P2P_DEVICE interfaces.
For example when a management packet arrives we can't tell for
which interface it is intended. To work around this, we store
a pointer to the interface where the last "radio operation" was
triggered such as scan or remain on channel, and we forward
management packets and scan results to this interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
supporting p2p_find, p2p_listen and p2p_connect
Use updated cfg80211_get_bss API (additional argument)
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
For example, stations inside a PBSS can communicate directly, and
the PCP role can be transferred between stations.
This change adds PBSS support, and has 2 main parts:
1. When starting an AP, add an option to start as a PCP instead.
This is implemented by a new PBSS flag which is passed as part of
the cfg80211_ap_settings structure.
2. When connecting to a BSS, add an option to connect to a PCP
instead of an AP. This is again implemented by a new PBSS flag,
added to the cfg80211_connect_params structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Switch to auto-generated version of wmi.h which is maintained
by FW team. This will allow better sync between teams in the
future and avoid bugs because of unexpected API changes.
The wmi.h will have many differences but most are cosmetic.
It also includes these real differences:
1. is_go parameter added to BCON_CTRL and START_PCP commands.
2. max_rx_pl_per_desc added to CFG_RX_CHAIN command.
3. various small API updates that are not currently used by
driver.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add support for discovery mode during scan. When discovery mode
is active, station transmits special beacons while scanning.
This can optimize the scan mainly when there is only one AP/PCP
around.
Discovery mode is implicitly used by firmware during P2P search.
Since there is currently no use case where user space has a
reason to directly control discovery mode, we expose it only
through a debugfs flag.
Also fix name confusion in the wmi_scan_type enumeration.
The type previously called WMI_LONG_SCAN is actually
WMI_ACTIVE_SCAN.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Check PN for encrypted frames.
Maintain PN data for Rx keys, pairwise per TID and group.
Print PN's in the debugfs "stations" entry, like:
[0] 04:ce:14:0a:3c:3d connected
[ 0] ([32] 0 TU) 0x0fe [____________________________|___] total 252 drop 0 (dup 0 + old 0) last 0x000
[ 0] PN [0+]000000000000 [1-]000000000000 [2-]000000000000 [3-]000000000000
[GR] PN [0-]000000000000 [1+]000000000000 [2+]000000000000 [3-]000000000000
Rx invalid frame: non-data 0, short 0, large 0, replay 0
Rx/MCS: 0 110 65 65 65 0 12 0 0 0 0 0 0
[1] 00:00:00:00:00:00 unused
[2] 00:00:00:00:00:00 unused
[3] 00:00:00:00:00:00 unused
[4] 00:00:00:00:00:00 unused
[5] 00:00:00:00:00:00 unused
[6] 00:00:00:00:00:00 unused
[7] 00:00:00:00:00:00 unused
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Needed by the upcoming merge of iwlwifi-next-for-kalle-2016-03-02 tag.
|
|
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.
Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
cfg80211_ops.disconnect() should wait for disconnect flow to
complete. If it does not, internal state becomes out of sync with
one in cfg80211. If one does stress test connect/disconnect
sequence, cfg80211 will issue next connect before disconnect
completed internally.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In the start_ap/change_beacon API, when we set up probe response
offloading, we only use the IE list from the probe response
template and not the IE list from the proberesp_ies argument.
As a result, we miss important IEs and it causes problems with
some scenarios such as P2P.
With this change, we merge the list of IEs from the probe response
template and proberesp_ies and send the merged list to the FW
for offloading. It is still FW responsibility to filter out
irrelevant IEs when sending probe response, based on the actual
contents of the probe request.
Also in case association response termplate is not provided,
we will use the merged list of IEs from probe response in the
association response as well.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
