Age | Commit message (Collapse) | Author |
|
[ Upstream commit 26a6d5274865532502c682ff378ac8ebe2886238 ]
The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3d6b72729cc2933906de8d2c602ae05e920b2122 ]
wil_err inside wil_rx_refill can flood the log buffer.
Replace it with wil_err_ratelimited.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6d9eb7ebae3d7e951bc0999235ae7028eb4cae4f ]
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6ccae584014ef7074359eb4151086beef66ecfa9 ]
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ea862048317aa76d0f22334202779a25530980c upstream.
syzbot reports a warning:
precision 33020 too large
WARNING: CPU: 0 PID: 9618 at lib/vsprintf.c:2471 set_precision+0x150/0x180 lib/vsprintf.c:2471
vsnprintf+0xa7b/0x19a0 lib/vsprintf.c:2547
kvasprintf+0xb2/0x170 lib/kasprintf.c:22
kasprintf+0xbb/0xf0 lib/kasprintf.c:59
hwsim_del_radio_nl+0x63a/0x7e0 drivers/net/wireless/mac80211_hwsim.c:3625
genl_family_rcv_msg_doit net/netlink/genetlink.c:672 [inline]
...
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Thus it seems that kasprintf() with "%.*s" format can not be used for
duplicating a string with arbitrary length. Replace it with kstrndup().
Note that later this string is limited to NL80211_WIPHY_NAME_MAXLEN == 64,
but the code is simpler this way.
Reported-by: syzbot+6693adf1698864d21734@syzkaller.appspotmail.com
Reported-by: syzbot+a4aee3f42d7584d76761@syzkaller.appspotmail.com
Cc: stable@kernel.org
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Link: https://lore.kernel.org/r/20200410123257.14559-1-tuomas.tynkkynen@iki.fi
[johannes: add note about length limit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 968ae2caad0782db5dbbabb560d3cdefd2945d38 upstream.
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994cde ("ath9k: add per-vif TX power capability")
Cc: stable@vger.kernel.org
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bcaeb886ade124331a6f3a5cef34a3f1484c0a03 ]
In qlcnic_83xx_get_reset_instruction_template, the variable
of null test is bad, so correct it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b317538c47943f9903860d83cc0060409e12d2ff ]
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
accessing PHY registers
[ Upstream commit 6110dff776f7fa65c35850ef65b41d3b39e2fac2 ]
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b9258a2cece4ec1f020715fe3554bc2e360f6264 ]
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Fixes: a1044e36e457 ("can: add slcan driver for serial/USB-serial CAN adapters")
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: security@kernel.org
Cc: wg@grandegger.com
Cc: mkl@pengutronix.de
Cc: davem@davemloft.net
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3e1221acf6a8f8595b5ce354bab4327a69d54d18 ]
Commit 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address entries")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit afa3b592953bfaecfb4f2f335ec5f935cff56804 ]
When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8262e6f9b1034ede34548a04dec4c302d92c9497 upstream.
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f3cc008bf6d59b8d93b4190e01d3e557b0040e15 ]
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 065fd83e1be2e1ba0d446a257fd86a3cc7bddb51 ]
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 2dcf75e2793c ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 384d91c267e621e0926062cfb3f20cb72dc16928 ]
gro_cells_init() returns error if memory allocation is failed.
But the vxlan module doesn't check the return value of gro_cells_init().
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")`
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2091a3d42b4f339eaeed11228e0cbe9d4f92f558 ]
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
This patch is a 1:1 copy of upstream slip.c commit f596c87005f7
("slip: not call free_netdev before rtnl_unlock in slip_open").
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b06d072ccc4b1acd0147b17914b7ad1caa1818bb ]
Only attach macsec to ethernet devices.
Syzbot was able to trigger a KMSAN warning in macsec_handle_frame
by attaching to a phonet device.
Macvlan has a similar check in macvlan_port_create.
v1->v2
- fix commit message typo
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 44343418d0f2f623cb9da6f5000df793131cbe3b ]
The KS8851 requires that packet RX and TX are mutually exclusive.
Currently, the driver hopes to achieve this by disabling interrupt
from the card by writing the card registers and by disabling the
interrupt on the interrupt controller. This however is racy on SMP.
Replace this approach by expanding the spinlock used around the
ks_start_xmit() TX path to ks_irq() RX path to assure true mutual
exclusion and remove the interrupt enabling/disabling, which is
now not needed anymore. Furthermore, disable interrupts also in
ks_net_stop(), which was missing before.
Note that a massive improvement here would be to re-use the KS8851
driver approach, which is to move the TX path into a worker thread,
interrupt handling to threaded interrupt, and synchronize everything
with mutexes, but that would be a much bigger rework, for a separate
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1e58252e334dc3f3756f424a157d1b7484464c40 upstream.
mwifiex_process_tdls_action_frame() without checking
the incoming tdls infomation element's vality before use it,
this may cause multi heap buffer overflows.
Fix them by putting vality check before use it.
IE is TLV struct, but ht_cap and ht_oper aren’t TLV struct.
the origin marvell driver code is wrong:
memcpy(&sta_ptr->tdls_cap.ht_oper, pos,....
memcpy((u8 *)&sta_ptr->tdls_cap.ht_capb, pos,...
Fix the bug by changing pos(the address of IE) to
pos+2 ( the address of IE value ).
Signed-off-by: qize wang <wangqize888888888@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 611d779af7cad2b87487ff58e4931a90c20b113c ]
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7469e83d2add567e4e0b063963db185f3167cea upstream.
Similar to commit 38f88c454042 ("bonding/alb: properly access headers
in bond_alb_xmit()"), we need to make sure arp header was pulled
in skb->head before blindly accessing it in rlb_arp_xmit().
Remove arp_pkt() private helper, since it is more readable/obvious
to have the following construct back to back :
if (!pskb_network_may_pull(skb, sizeof(*arp)))
return NULL;
arp = (struct arp_pkt *)skb_network_header(skb);
syzbot reported :
BUG: KMSAN: uninit-value in bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
BUG: KMSAN: uninit-value in rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
BUG: KMSAN: uninit-value in bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
CPU: 0 PID: 12743 Comm: syz-executor.4 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
__bond_start_xmit drivers/net/bonding/bond_main.c:4257 [inline]
bond_start_xmit+0x85d/0x2f70 drivers/net/bonding/bond_main.c:4282
__netdev_start_xmit include/linux/netdevice.h:4524 [inline]
netdev_start_xmit include/linux/netdevice.h:4538 [inline]
xmit_one net/core/dev.c:3470 [inline]
dev_hard_start_xmit+0x531/0xab0 net/core/dev.c:3486
__dev_queue_xmit+0x37de/0x4220 net/core/dev.c:4063
dev_queue_xmit+0x4b/0x60 net/core/dev.c:4096
packet_snd net/packet/af_packet.c:2967 [inline]
packet_sendmsg+0x8347/0x93b0 net/packet/af_packet.c:2992
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
__sys_sendto+0xc1b/0xc50 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto+0x107/0x130 net/socket.c:2006
__x64_sys_sendto+0x6e/0x90 net/socket.c:2006
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45c479
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fc77ffbbc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fc77ffbc6d4 RCX: 000000000045c479
RDX: 000000000000000e RSI: 00000000200004c0 RDI: 0000000000000003
RBP: 000000000076bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000a04 R14: 00000000004cc7b0 R15: 000000000076bf2c
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
slab_alloc_node mm/slub.c:2793 [inline]
__kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1051 [inline]
alloc_skb_with_frags+0x18c/0xa70 net/core/skbuff.c:5766
sock_alloc_send_pskb+0xada/0xc60 net/core/sock.c:2242
packet_alloc_skb net/packet/af_packet.c:2815 [inline]
packet_snd net/packet/af_packet.c:2910 [inline]
packet_sendmsg+0x66a0/0x93b0 net/packet/af_packet.c:2992
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
__sys_sendto+0xc1b/0xc50 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto+0x107/0x130 net/socket.c:2006
__x64_sys_sendto+0x6e/0x90 net/socket.c:2006
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 110a40dfb708fe940a3f3704d470e431c368d256 ]
Before accessing various fields in IPV4 network header
and TCP header, make sure the packet :
- Has IP version 4 (ip->version == 4)
- Has not a silly network length (ip->ihl >= 5)
- Is big enough to hold network and transport headers
- Has not a silly TCP header size (th->doff >= sizeof(struct tcphdr) / 4)
syzbot reported :
BUG: KMSAN: uninit-value in slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270
CPU: 0 PID: 11728 Comm: syz-executor231 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270
ppp_send_frame drivers/net/ppp/ppp_generic.c:1637 [inline]
__ppp_xmit_process+0x1902/0x2970 drivers/net/ppp/ppp_generic.c:1495
ppp_xmit_process+0x147/0x2f0 drivers/net/ppp/ppp_generic.c:1516
ppp_write+0x6bb/0x790 drivers/net/ppp/ppp_generic.c:512
do_loop_readv_writev fs/read_write.c:717 [inline]
do_iter_write+0x812/0xdc0 fs/read_write.c:1000
compat_writev+0x2df/0x5a0 fs/read_write.c:1351
do_compat_pwritev64 fs/read_write.c:1400 [inline]
__do_compat_sys_pwritev fs/read_write.c:1420 [inline]
__se_compat_sys_pwritev fs/read_write.c:1414 [inline]
__ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414
do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410
entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f7cd99
Code: 90 e8 0b 00 00 00 f3 90 0f ae e8 eb f9 8d 74 26 00 89 3c 24 c3 90 90 90 90 90 90 90 90 90 90 90 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 002b:00000000ffdb84ac EFLAGS: 00000217 ORIG_RAX: 000000000000014e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00000000200001c0
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 0000000040047459 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
slab_alloc_node mm/slub.c:2793 [inline]
__kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1051 [inline]
ppp_write+0x115/0x790 drivers/net/ppp/ppp_generic.c:500
do_loop_readv_writev fs/read_write.c:717 [inline]
do_iter_write+0x812/0xdc0 fs/read_write.c:1000
compat_writev+0x2df/0x5a0 fs/read_write.c:1351
do_compat_pwritev64 fs/read_write.c:1400 [inline]
__do_compat_sys_pwritev fs/read_write.c:1420 [inline]
__se_compat_sys_pwritev fs/read_write.c:1414 [inline]
__ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414
do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410
entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
Fixes: b5451d783ade ("slip: Move the SLIP drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ab14961d10d02d20767612c78ce148f6eb85bd58 ]
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22fc ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce9a4186f9ac475c415ffd20348176a4ea366670 ]
The Rx bound multicast packets are deferred to a workqueue and
macvlan can also suffer from the same attack that was discovered
by Syzbot for IPvlan. This solution is not as effective as in
IPvlan. IPvlan defers all (Tx and Rx) multicast packet processing
to a workqueue while macvlan does this way only for the Rx. This
fix should address the Rx codition to certain extent.
Tx is still suseptible. Tx multicast processing happens when
.ndo_start_xmit is called, hence we cannot add cond_resched().
However, it's not that severe since the user which is generating
/ flooding will be affected the most.
Fixes: 412ca1550cbe ("macvlan: Move broadcasts into a work queue")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ad8192767c9f9cf97da57b9ffcea70fb100febef ]
IPvlan in L3 mode discards outbound multicast packets but performs
the check before ensuring the ether-header is set or not. This is
an error that Eric found through code browsing.
Fixes: 2ad7bf363841 (“ipvlan: Initial check-in of the IPVLAN driver.”)
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit afe207d80a61e4d6e7cfa0611a4af46d0ba95628 ]
Commit e18b353f102e ("ipvlan: add cond_resched_rcu() while
processing muticast backlog") added a cond_resched_rcu() in a loop
using rcu protection to iterate over slaves.
This is breaking rcu rules, so lets instead use cond_resched()
at a point we can reschedule
Fixes: e18b353f102e ("ipvlan: add cond_resched_rcu() while processing muticast backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cccc200fcaf04cff4342036a72e51d6adf6c98c1 upstream.
Currently, if IPv6 is enabled on top of an ipvlan device in l3
mode, the following warning message:
Dropped {multi|broad}cast of type= [86dd]
is emitted every time that a RS is generated and dmseg is soon
filled with irrelevant messages. Replace pr_warn with pr_debug,
to preserve debuggability, without scaring the sysadmin.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 63aae7b17344d4b08a7d05cb07044de4c0f9dcc6 ]
There is a problem when ipvlan slaves are created on a master device that
is a vmxnet3 device (ipvlan in VMware guests). The vmxnet3 driver does not
support unicast address filtering. When an ipvlan device is brought up in
ipvlan_open(), the ipvlan driver calls dev_uc_add() to add the hardware
address of the vmxnet3 master device to the unicast address list of the
master device, phy_dev->uc. This inevitably leads to the vmxnet3 master
device being forced into promiscuous mode by __dev_set_rx_mode().
Promiscuous mode is switched on the master despite the fact that there is
still only one hardware address that the master device should use for
filtering in order for the ipvlan device to be able to receive packets.
The comment above struct net_device describes the uc_promisc member as a
"counter, that indicates, that promiscuous mode has been enabled due to
the need to listen to additional unicast addresses in a device that does
not implement ndo_set_rx_mode()". Moreover, the design of ipvlan
guarantees that only the hardware address of a master device,
phy_dev->dev_addr, will be used to transmit and receive all packets from
its ipvlan slaves. Thus, the unicast address list of the master device
should not be modified by ipvlan_open() and ipvlan_stop() in order to make
ipvlan a workable option on masters that do not support unicast address
filtering.
Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver")
Reported-by: Per Sundstrom <per.sundstrom@redqube.se>
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e18b353f102e371580f3f01dd47567a25acc3c1d ]
If there are substantial number of slaves created as simulated by
Syzbot, the backlog processing could take much longer and result
into the issue found in the Syzbot report.
INFO: rcu_sched detected stalls on CPUs/tasks:
(detected by 1, t=10502 jiffies, g=5049, c=5048, q=752)
All QSes seen, last rcu_sched kthread activity 10502 (4294965563-4294955061), jiffies_till_next_fqs=1, root ->qsmask 0x0
syz-executor.1 R running task on cpu 1 10984 11210 3866 0x30020008 179034491270
Call Trace:
<IRQ>
[<ffffffff81497163>] _sched_show_task kernel/sched/core.c:8063 [inline]
[<ffffffff81497163>] _sched_show_task.cold+0x2fd/0x392 kernel/sched/core.c:8030
[<ffffffff8146a91b>] sched_show_task+0xb/0x10 kernel/sched/core.c:8073
[<ffffffff815c931b>] print_other_cpu_stall kernel/rcu/tree.c:1577 [inline]
[<ffffffff815c931b>] check_cpu_stall kernel/rcu/tree.c:1695 [inline]
[<ffffffff815c931b>] __rcu_pending kernel/rcu/tree.c:3478 [inline]
[<ffffffff815c931b>] rcu_pending kernel/rcu/tree.c:3540 [inline]
[<ffffffff815c931b>] rcu_check_callbacks.cold+0xbb4/0xc29 kernel/rcu/tree.c:2876
[<ffffffff815e3962>] update_process_times+0x32/0x80 kernel/time/timer.c:1635
[<ffffffff816164f0>] tick_sched_handle+0xa0/0x180 kernel/time/tick-sched.c:161
[<ffffffff81616ae4>] tick_sched_timer+0x44/0x130 kernel/time/tick-sched.c:1193
[<ffffffff815e75f7>] __run_hrtimer kernel/time/hrtimer.c:1393 [inline]
[<ffffffff815e75f7>] __hrtimer_run_queues+0x307/0xd90 kernel/time/hrtimer.c:1455
[<ffffffff815e90ea>] hrtimer_interrupt+0x2ea/0x730 kernel/time/hrtimer.c:1513
[<ffffffff844050f4>] local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1031 [inline]
[<ffffffff844050f4>] smp_apic_timer_interrupt+0x144/0x5e0 arch/x86/kernel/apic/apic.c:1056
[<ffffffff84401cbe>] apic_timer_interrupt+0x8e/0xa0 arch/x86/entry/entry_64.S:778
RIP: 0010:do_raw_read_lock+0x22/0x80 kernel/locking/spinlock_debug.c:153
RSP: 0018:ffff8801dad07ab8 EFLAGS: 00000a02 ORIG_RAX: ffffffffffffff12
RAX: 0000000000000000 RBX: ffff8801c4135680 RCX: 0000000000000000
RDX: 1ffff10038826afe RSI: ffff88019d816bb8 RDI: ffff8801c41357f0
RBP: ffff8801dad07ac0 R08: 0000000000004b15 R09: 0000000000310273
R10: ffff88019d816bb8 R11: 0000000000000001 R12: ffff8801c41357e8
R13: 0000000000000000 R14: ffff8801cfb19850 R15: ffff8801cfb198b0
[<ffffffff8101460e>] __raw_read_lock_bh include/linux/rwlock_api_smp.h:177 [inline]
[<ffffffff8101460e>] _raw_read_lock_bh+0x3e/0x50 kernel/locking/spinlock.c:240
[<ffffffff840d78ca>] ipv6_chk_mcast_addr+0x11a/0x6f0 net/ipv6/mcast.c:1006
[<ffffffff84023439>] ip6_mc_input+0x319/0x8e0 net/ipv6/ip6_input.c:482
[<ffffffff840211c8>] dst_input include/net/dst.h:449 [inline]
[<ffffffff840211c8>] ip6_rcv_finish+0x408/0x610 net/ipv6/ip6_input.c:78
[<ffffffff840214de>] NF_HOOK include/linux/netfilter.h:292 [inline]
[<ffffffff840214de>] NF_HOOK include/linux/netfilter.h:286 [inline]
[<ffffffff840214de>] ipv6_rcv+0x10e/0x420 net/ipv6/ip6_input.c:278
[<ffffffff83a29efa>] __netif_receive_skb_one_core+0x12a/0x1f0 net/core/dev.c:5303
[<ffffffff83a2a15c>] __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:5417
[<ffffffff83a2f536>] process_backlog+0x216/0x6c0 net/core/dev.c:6243
[<ffffffff83a30d1b>] napi_poll net/core/dev.c:6680 [inline]
[<ffffffff83a30d1b>] net_rx_action+0x47b/0xfb0 net/core/dev.c:6748
[<ffffffff846002c8>] __do_softirq+0x2c8/0x99a kernel/softirq.c:317
[<ffffffff813e656a>] invoke_softirq kernel/softirq.c:399 [inline]
[<ffffffff813e656a>] irq_exit+0x16a/0x1a0 kernel/softirq.c:439
[<ffffffff84405115>] exiting_irq arch/x86/include/asm/apic.h:561 [inline]
[<ffffffff84405115>] smp_apic_timer_interrupt+0x165/0x5e0 arch/x86/kernel/apic/apic.c:1058
[<ffffffff84401cbe>] apic_timer_interrupt+0x8e/0xa0 arch/x86/entry/entry_64.S:778
</IRQ>
RIP: 0010:__sanitizer_cov_trace_pc+0x26/0x50 kernel/kcov.c:102
RSP: 0018:ffff880196033bd8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff12
RAX: ffff88019d8161c0 RBX: 00000000ffffffff RCX: ffffc90003501000
RDX: 0000000000000002 RSI: ffffffff816236d1 RDI: 0000000000000005
RBP: ffff880196033bd8 R08: ffff88019d8161c0 R09: 0000000000000000
R10: 1ffff10032c067f0 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000080 R14: 0000000000000000 R15: 0000000000000000
[<ffffffff816236d1>] do_futex+0x151/0x1d50 kernel/futex.c:3548
[<ffffffff816260f0>] C_SYSC_futex kernel/futex_compat.c:201 [inline]
[<ffffffff816260f0>] compat_SyS_futex+0x270/0x3b0 kernel/futex_compat.c:175
[<ffffffff8101da17>] do_syscall_32_irqs_on arch/x86/entry/common.c:353 [inline]
[<ffffffff8101da17>] do_fast_syscall_32+0x357/0xe1c arch/x86/entry/common.c:415
[<ffffffff84401a9b>] entry_SYSENTER_compat+0x8b/0x9d arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f23c69
RSP: 002b:00000000f5d1f12c EFLAGS: 00000282 ORIG_RAX: 00000000000000f0
RAX: ffffffffffffffda RBX: 000000000816af88 RCX: 0000000000000080
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000000000816af8c
RBP: 00000000f5d1f228 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
rcu_sched kthread starved for 10502 jiffies! g5049 c5048 f0x2 RCU_GP_WAIT_FQS(3) ->state=0x0 ->cpu=1
rcu_sched R running task on cpu 1 13048 8 2 0x90000000 179099587640
Call Trace:
[<ffffffff8147321f>] context_switch+0x60f/0xa60 kernel/sched/core.c:3209
[<ffffffff8100095a>] __schedule+0x5aa/0x1da0 kernel/sched/core.c:3934
[<ffffffff810021df>] schedule+0x8f/0x1b0 kernel/sched/core.c:4011
[<ffffffff8101116d>] schedule_timeout+0x50d/0xee0 kernel/time/timer.c:1803
[<ffffffff815c13f1>] rcu_gp_kthread+0xda1/0x3b50 kernel/rcu/tree.c:2327
[<ffffffff8144b318>] kthread+0x348/0x420 kernel/kthread.c:246
[<ffffffff84400266>] ret_from_fork+0x56/0x70 arch/x86/entry/entry_64.S:393
Fixes: ba35f8588f47 (“ipvlan: Defer multicast / broadcast processing to a work-queue”)
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 669fcd7795900cd1880237cbbb57a7db66cb9ac8 ]
Add missing attribute validation for TEAM_ATTR_OPTION_ARRAY_INDEX
to the netlink policy.
Fixes: b13033262d24 ("team: introduce array options")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dd25cb272ccce4db67dc8509278229099e4f5e99 ]
Add missing attribute validation for TEAM_ATTR_OPTION_PORT_IFINDEX
to the netlink policy.
Fixes: 80f7c6683fe0 ("team: add support for per-port options")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 31d9a1c524964bac77b7f9d0a1ac140dc6b57461 ]
Add missing attribute validation for IFLA_MACSEC_PORT
to the netlink policy.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a9b952d267e59a3b405e644930f46d252cea7122 ]
MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true. The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU. We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs. Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d64c7a08034b32c285e576208ae44fc3ba3fa7df ]
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6fc498bc82929ee23aa2f35a828c6178dfd3f823 ]
SCI should be updated, because it contains MAC in its first 6 octets.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 503ba7c6961034ff0047707685644cad9287c226 upstream.
It is currently possible for a PHY device to be suspended as part of a
network device driver's suspend call while it is still being attached to
that net_device, either via phy_suspend() or implicitly via phy_stop().
Later on, when the MDIO bus controller get suspended, we would attempt
to suspend again the PHY because it is still attached to a network
device.
This is both a waste of time and creates an opportunity for improper
clock/power management bugs to creep in.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b566f70e1bf65b189b66eb3de6f431c30f7dff2 upstream.
This reverts:
ef1b5bf506b1 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b81296 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
[just take the ef1b5bf506b1 revert - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 58292104832fef6cb4a89f736012c0e0724c3442 ]
The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that
BE[3:0] signals are active high. This contradicts the measurements
of the behavior of the actual chip, where these signals behave as
active low. For example, to read the CIDER register, the bus must
expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edacb098ea9c31589276152f09b4439052c0f2b1 ]
The packet data written to and read from Micrel KSZ8851-16MLLI must be
byte-swapped in 16-bit mode, add this byte-swapping.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69233bba6543a37755158ca3382765387b8078df ]
This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown,
however the speculation is that this was some sort of attempt to support
the 8-bit bus mode.
As per the KS8851-16MLL documentation, all two registers accessed via the
8-bit accessors are internally 16-bit registers, so reading them using
16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read
outright, as it is already a concatenation of two 8-bit reads of that
register. The KS_RXQCR accesses are 8-bit only, however writing the top
8 bits of the register is OK as well, since the driver caches the entire
16-bit register value anyway.
Finally, the driver is not used by any hardware in the kernel right now.
The only hardware available to me is one with 16-bit bus, so I have no
way to test the 8-bit bus mode, however it is unlikely this ever really
worked anyway. If the 8-bit bus mode is ever required, it can be easily
added by adjusting the 16-bit accessors to do 2 consecutive accesses,
which is how this should have been done from the beginning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5a44c71ccda60a50073c5d7fe3f694cdfa3ab0c2 upstream.
'alloc_etherdev_mqs()' expects first 'tx', then 'rx'. The semantic here
looks reversed.
Reorder the arguments passed to 'alloc_etherdev_mqs()' in order to keep
the correct semantic.
In fact, this is a no-op because both XGENE_NUM_[RT]X_RING are 8.
Fixes: 107dec2749fe ("drivers: net: xgene: Add support for multiple queues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f3ab6221e4c87960347d65c7cab9bd917d1f637 upstream.
When link is down, writes to the device might fail with
-EIO. Userspace needs an indication when the status is resolved. As a
fix, tun_net_open() attempts to wake up writers - but that is only
effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is
not the case of vhost_net which only poll for EPOLLOUT after it meets
errors during sendmsg().
This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when
socket is not writable or device is down to guarantee EPOLLOUT will be
raised in either tun_chr_poll() or tun_sock_write_space() after device
is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 1bd4978a88ac2 ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
|
|
After include 3b5a39979daf ("slip: Fix memory leak in slip_open error path")
and e58c19124189 ("slip: Fix use-after-free Read in slip_open") with 4.4.y/4.9.y.
We will trigger a bug since we can double free sl->dev in slip_open. Actually,
we should backport cf124db566e6 ("net: Fix inconsistent teardown and release
of private netdev state.") too since it has delete free_netdev from sl_free_netdev.
Fix it by delete free_netdev from slip_open.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 470793a78ce344bd53d31e0c2d537f71ba957547 upstream.
As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing
the key or indirection table using ethtool while keeping the same hash
function.
Also add a function for retrieving the current hash function from
the ena-com layer.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f08e98d62799e53c89dbf2c9a49d77e20ca648c upstream.
The mii management register in iproc mdio block
does not have a retention register so it is lost on suspend.
Save and restore value of register while resuming from suspend.
Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c207979f5ae10ed70aff1bb13f39f0736973de99 ]
comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().
The bug scenario is as follows:
* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
this can still happen because our device can still receive callbacks
from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
to NULL
Fix:
Added a check that comp_ctx is not NULL
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
table
[ Upstream commit 92569fd27f5cb0ccbdf7c7d70044b690e89a0277 ]
The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.
Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0 1 2 3 4 5
Tx Rx Tx Rx Tx Rx
The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.
The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4844470d472d660c26149ad764da2406adb13423 ]
The device receives, stores and retrieves the hash function value as bits
and not as their enum value.
The bug:
* In ena_com_set_hash_function() we set
cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
(1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
is stored in rss->hash_func instead of it's enum value)
The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c8923c0a64fb5d14bebb9a9065d2dc25ac5e600 ]
On old hardware, getting / setting the hash function is not supported while
gettting / setting the indirection table is.
This commit enables us to still show the indirection table on older
hardwares by setting the hash function and key to NULL.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|