Age | Commit message (Collapse) | Author |
|
commit d86b5672b1adb98b4cdd6fbf0224bbfb03db6e2e upstream.
Unavoidable crashes in netfront_resume() and netback_changed() after a
previous fail in talk_to_netback() (e.g. when we fail to read MAC from
xenstore) were discovered. The failure path in talk_to_netback() does
unregister/free for netdev but we don't reset drvdata and we try accessing
it after resume.
Fix the bug by removing the whole xen device completely with
device_unregister(), this guarantees we won't have any calls into netfront
after a failure.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 01f8902bcf3ff124d0aeb88a774180ebcec20ace ]
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ebf692f85ff78092cd238166d8d7ec51419f9c02 ]
This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <mart@greenhost.nl>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e2e004acc7cbe3c531e752a270a74e95cde3ea48 ]
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4993b39ab04b083ff6ee1147e7e7f120feb6bf7f ]
Recent commit 34393529163a ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.
The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
interface is down). In this case the initial MAC programmed by PF
needs to be deleted.
The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.
Example of failure without the fix (immediately after fresh boot):
# ip link set eth0 up <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF port 0
# ip link set eth8 up <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error
# echo 0 > /sys/class/net/eth0/device/sriov_numvfs <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...
# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up
Initialization is now OK.
v2 - Corrected the comment and condition check suggested by Suresh & Harsha
Fixes: 34393529163a ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c73e44269369e936165f0f9b61f1f09a11dae01c ]
This fixes the following smatch and coccinelle warnings:
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119 xcv_setup_link() error: we previously assumed 'xcv' could be null (see line 118) [smatch]
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119:16-20: ERROR: xcv is NULL but dereferenced. [coccinelle]
Fixes: 6465859aba1e66a5 ("net: thunderx: Add RGMII interface type support")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cf626c3b252b2c9d131be0dd66096ec3bf729e54 ]
As pr commit "net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause"
this phy driver should not set these feature bits.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3ab1b469e847ba425af3c5ad5068cc94b55b38d0 ]
The use of the passed through netlink src_net to check for a
cross netns operation was wrong. Using the GTP socket and the
GTP netdevice is always correct (even if the netdev has been
moved to new netns after link creation).
Remove the now obsolete net field from gtp_dev.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c6ce1d08eede4c2968ed08aafa3165e8e183c5a1 ]
3GPP TS 29.281 and 3GPP TS 29.060 imply that GTP-U packets should be
sent with the DF bit cleared. For example 3GPP TS 29.060, Release 8,
Section 13.2.2:
> Backbone router: Any router in the backbone may fragment the GTP
> packet if needed, according to IPv4.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Acked-by: Harald Welte <laforge@netfilter.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 18a3ed59d09cf81a6447aadf6931bf0c9ffec5e0 ]
Remove Rx overflow log messages as in an environment where logging results
in network traffic logging may cause further overflows.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce7e40c432ba84da104438f6799d460a4cad41bc ]
ipddp_route structs contain alignment padding so kernel heap memory
is leaked when they are copied to user space in
ipddp_ioctl(SIOCFINDIPDDPRT). Change kmalloc() to kzalloc() to clear
that memory.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6052cd1af86f9833b6b0b60d5d4787c4a06d65ea ]
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: b717241 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1d0f110a2c6c4bca3dbcc4b0e27f1e3dc2d44a2c ]
Commit 988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 988d44b be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 38e5a85562a6cd911fc26d951d576551a688574c ]
Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.
For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.
Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bb7da333d0a9f3bddc08f84187b7579a3f68fd24 ]
Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a9a8cdb368d99bb655b5cdabea560446db0527cc ]
ip6_route_output() never returns NULL so
check dst->error instead of !dst.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 61b6034c6cfdcb265bb453505c3d688e7567727a ]
is_power_of_2 expects unsigned long and we pass u64 max_val_cycles,
this will be truncated on 32 bit systems, and the result is not what we
were expecting.
div_u64 expects u32 as a second argument and we pass
max_val_cycles_rounded which is u64 hence it will always be truncated.
Fix was tested on both 64 and 32 bit systems and got same results for
max_val_cycles and max_val_cycles_rounded.
Fixes: 4850cf458157 ("net/mlx4_en: Resolve dividing by zero in 32-bit system")
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d15697de60db5570532fdedb8e13b2251d65b8e3 ]
The driver does not check if mapping dma memory succeed.
The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7cfe0455ee1218add152e986b89b4bb8dbeafcdd ]
The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:
[00]: 0x05020001 0x000015B3 0x0099ACE2 0x00955B31
[04]: 0x0099ACE2 0x00060730 0x00000004 0x00000000
[08]: 0x0044C754 0x00412C10 0x00000000 0x00409C54
[12]: 0x00000009 0x00000000 0x00952F6C 0x00952F77
[16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
[20]: 0x4099ACE2 0x0040E858 0x00421254 0x004127F4
[24]: 0x8099B9B2 0x0040E8B8 0x00000000 0xC099ACE2
[28]: 0x800B75CB 0x0040E8F8 0x00000007 0x00005008
[32]: 0x809B048A 0x0040E958 0x00000010 0x00433B10
[36]: 0x809AFBBC 0x0040E9A8 0x0042BB74 0x0042BBBC
[40]: 0x8091D252 0x0040E9C8 0x0042BBBC 0x00000001
[44]: 0x809FFA45 0x0040EA78 0x0043D3E4 0x0042C2C8
[48]: 0x809FCEF4 0x0040EA98 0x0043D3E4 0x00000001
[52]: 0x80911210 0x0040EAE8 0x00000010 0x004041D0
[56]: 0x80911154 0x0040EB28 0x00400000 0x00000000
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 486b5c22ea1d35e00e90dd79a32a9ee530b18915 ]
With the added support for the bnxt_re RDMA driver, both drivers can be
allocating completion rings in any order. The firmware does not know
which completion ring should be receiving async events. Add an
extra step to tell firmware the completion ring number for receiving
async events after bnxt_en allocates the completion rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 097e46d2ae90265d1afe141ba6208ba598b79e01 ]
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d2e202c06ca42d353d95df12437740921a6d05b5 ]
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 88407beb1b1462f706a1950a355fd086e1c450b6 ]
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 74c8719b8ee0922593a5cbec0bd6127d86d8a2f4 ]
If we have sdio work requests received when sdio card reset is
happening, we may end up accessing older save_adapter pointer
later which is already freed during card reset.
This patch solves the problem by cancelling those pending requests.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c705a6b3aa7804d7bc6660183f51e510c61dc807 ]
We accidentally return success when adm8211_alloc_rings() fails but we
should preserve the error code.
Fixes: cc0b88cf5ecf ("[PATCH] Add adm8211 802.11b wireless driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a51b89698ccc93c7e274eb71377fae49c4593ab2 ]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 107fded7bf616ad6f46823d98b8ed6405d7adf2d ]
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188841
Reported-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6b6bbb5922a4b1d4b58125a572da91010295fba3 ]
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4aea7a5c5e940c1723add439f4088844cd26196d upstream.
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc33
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19110cfbb34d4af0cdfe14cd243f3b09dc95b013 upstream.
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3509f8bc7b0560044c15f0e3ecfde1d9af757a6 upstream.
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4c40e51f9c32c6dd8adf606624c930a1c4d9bbb upstream.
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a9a17e3bb4564caf4bfe2a6783ae1287667d188 upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b8edcc685b5e2c3c37aa13dc50a88e84a5bfef8 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f72271e2a0ae4277d53c4053f5eed8bb346ba38a upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae0c585d93dfaf923d2c7eb44b2c3ab92854ea9b upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e1f9ca546556e508d021545861f6b5fc75a95fe upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4cb99185b4cc96c0a1c70104dc21ae14d7e7f28 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52c6912fde0133981ee50ba08808f257829c4c93 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc09785de0a364427a5df63d703bae9a306ed116 upstream.
ieee80211_register_hw() in p54_register_common() may fail and leds won't
get initialized. Currently p54_unregister_common() doesn't check that and
always calls p54_unregister_leds(). The fix is to check priv->registered
flag before calling p54_unregister_leds().
Found by syzkaller.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 1404 Comm: kworker/1:1 Not tainted
4.14.0-rc1-42251-gebb2c2437d80-dirty #205
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x6c4/0x1a00 kernel/locking/lockdep.c:769
__lock_acquire+0x27e/0x4550 kernel/locking/lockdep.c:3385
lock_acquire+0x259/0x620 kernel/locking/lockdep.c:4002
flush_work+0xf0/0x8c0 kernel/workqueue.c:2886
__cancel_work_timer+0x51d/0x870 kernel/workqueue.c:2961
cancel_delayed_work_sync+0x1f/0x30 kernel/workqueue.c:3081
p54_unregister_leds+0x6c/0xc0 drivers/net/wireless/intersil/p54/led.c:160
p54_unregister_common+0x3d/0xb0 drivers/net/wireless/intersil/p54/main.c:856
p54u_disconnect+0x86/0x120 drivers/net/wireless/intersil/p54/p54usb.c:1073
usb_unbind_interface+0x21c/0xa90 drivers/usb/core/driver.c:423
__device_release_driver drivers/base/dd.c:861
device_release_driver_internal+0x4f4/0x5c0 drivers/base/dd.c:893
device_release_driver+0x1e/0x30 drivers/base/dd.c:918
bus_remove_device+0x2f4/0x4b0 drivers/base/bus.c:565
device_del+0x5c4/0xab0 drivers/base/core.c:1985
usb_disable_device+0x1e9/0x680 drivers/usb/core/message.c:1170
usb_disconnect+0x260/0x7a0 drivers/usb/core/hub.c:2124
hub_port_connect drivers/usb/core/hub.c:4754
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x1318/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
process_scheduled_works kernel/workqueue.c:2179
worker_thread+0xb2b/0x1850 kernel/workqueue.c:2255
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f2a162fab15aee243178b5308bb5d1206fc4043 upstream.
We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.
Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 519ce2f933fa14acf69d5c8cabcc18711943d629 upstream.
In routine rtl92ee_set_fw_rsvdpagepkt(), the driver allocates an skb, but
never calls rtl_cmd_send_packet(), which will free the buffer. All other
rtlwifi drivers perform this operation correctly.
This problem has been in the driver since it was included in the kernel.
Fortunately, each firmware load only leaks 4 buffers, which likely
explains why it has not previously been detected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bfa62a52cad93686bb8d8171ea5288813248a7c6 upstream.
ENOENT usb error mean "specified interface or endpoint does not exist or
is not enabled". Mark device not present when we encounter this error
similar like we do with ENODEV error.
Otherwise we can have infinite loop in rt2x00usb_work_rxdone(), because
we remove and put again RX entries to the queue infinitely.
We can have similar situation when submit urb will fail all the time
with other error, so we need consider to limit number of entries
processed by rxdone work. But for now, since the patch fixes
reproducible soft lockup issue on single processor systems
and taken ENOENT error meaning, let apply this fix.
Patch adds additional ENOENT check not only in rx kick routine, but
also on other places where we check for ENODEV error.
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Debugged-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cc54c1d32e6a4bb3f116721abf900513173e4d02 ]
This patch try to fix the building error on MIPS. The reason is MIPS
has already defined the LONG macro, which conflicts with the LONG enum
in drivers/net/ethernet/fealnx.c.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8f5624629105589bcc23d0e51cc01bd8103d09a5 ]
When asix_suspend() is called dev->driver_priv might not have been
assigned a value, so we need to check that it's not NULL.
Similar issue is present in asix_resume(), this patch fixes it as well.
Found by syzkaller.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc4-43422-geccacdd69a8c #400
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bb36300 task.stack: ffff88006bba8000
RIP: 0010:asix_suspend+0x76/0xc0 drivers/net/usb/asix_devices.c:629
RSP: 0018:ffff88006bbae718 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff880061ba3b80 RCX: 1ffff1000c34d644
RDX: 0000000000000001 RSI: 0000000000000402 RDI: 0000000000000008
RBP: ffff88006bbae738 R08: 1ffff1000d775cad R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800630a8b40
R13: 0000000000000000 R14: 0000000000000402 R15: ffff880061ba3b80
FS: 0000000000000000(0000) GS:ffff88006c600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ff33cf89000 CR3: 0000000061c0a000 CR4: 00000000000006f0
Call Trace:
usb_suspend_interface drivers/usb/core/driver.c:1209
usb_suspend_both+0x27f/0x7e0 drivers/usb/core/driver.c:1314
usb_runtime_suspend+0x41/0x120 drivers/usb/core/driver.c:1852
__rpm_callback+0x339/0xb60 drivers/base/power/runtime.c:334
rpm_callback+0x106/0x220 drivers/base/power/runtime.c:461
rpm_suspend+0x465/0x1980 drivers/base/power/runtime.c:596
__pm_runtime_suspend+0x11e/0x230 drivers/base/power/runtime.c:1009
pm_runtime_put_sync_autosuspend ./include/linux/pm_runtime.h:251
usb_new_device+0xa37/0x1020 drivers/usb/core/hub.c:2487
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Code: 8d 7c 24 20 48 89 fa 48 c1 ea 03 80 3c 02 00 75 5b 48 b8 00 00
00 00 00 fc ff df 4d 8b 6c 24 20 49 8d 7d 08 48 89 fa 48 c1 ea 03 <80>
3c 02 00 75 34 4d 8b 6d 08 4d 85 ed 74 0b e8 26 2b 51 fd 4c
RIP: asix_suspend+0x76/0xc0 RSP: ffff88006bbae718
---[ end trace dfc4f5649284342c ]---
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0de0add10e587effa880c741c9413c874f16be91 ]
When we receive a packet on a QMI device in raw IP mode, we should call
skb_reset_mac_header() to ensure that skb->mac_header contains a valid
offset in the packet. While it shouldn't really matter, the packets have
no MAC header and the interface is configured as-such, it seems certain
parts of the network stack expects a "good" value in skb->mac_header.
Without the skb_reset_mac_header() call added in this patch, for example
shaping traffic (using tc) triggers the following oops on the first
received packet:
[ 303.642957] skbuff: skb_under_panic: text:8f137918 len:177 put:67 head:8e4b0f00 data:8e4b0eff tail:0x8e4b0fb0 end:0x8e4b1520 dev:wwan0
[ 303.655045] Kernel bug detected[#1]:
[ 303.658622] CPU: 1 PID: 1002 Comm: logd Not tainted 4.9.58 #0
[ 303.664339] task: 8fdf05e0 task.stack: 8f15c000
[ 303.668844] $ 0 : 00000000 00000001 0000007a 00000000
[ 303.674062] $ 4 : 8149a2fc 8149a2fc 8149ce20 00000000
[ 303.679284] $ 8 : 00000030 3878303a 31623465 20303235
[ 303.684510] $12 : ded731e3 2626a277 00000000 03bd0000
[ 303.689747] $16 : 8ef62b40 00000043 8f137918 804db5fc
[ 303.694978] $20 : 00000001 00000004 8fc13800 00000003
[ 303.700215] $24 : 00000001 8024ab10
[ 303.705442] $28 : 8f15c000 8fc19cf0 00000043 802cc920
[ 303.710664] Hi : 00000000
[ 303.713533] Lo : 74e58000
[ 303.716436] epc : 802cc920 skb_panic+0x58/0x5c
[ 303.721046] ra : 802cc920 skb_panic+0x58/0x5c
[ 303.725639] Status: 11007c03 KERNEL EXL IE
[ 303.729823] Cause : 50800024 (ExcCode 09)
[ 303.733817] PrId : 0001992f (MIPS 1004Kc)
[ 303.737892] Modules linked in: rt2800pci rt2800mmio rt2800lib qcserial ppp_async option usb_wwan rt2x00pci rt2x00mmio rt2x00lib rndis_host qmi_wwan ppp_generic nf_nat_pptp nf_conntrack_pptp nf_conntrack_ipv6 mt76x2i
Process logd (pid: 1002, threadinfo=8f15c000, task=8fdf05e0, tls=77b3eee4)
[ 303.962509] Stack : 00000000 80408990 8f137918 000000b1 00000043 8e4b0f00 8e4b0eff 8e4b0fb0
[ 303.970871] 8e4b1520 8fec1800 00000043 802cd2a4 6e000045 00000043 00000000 8ef62000
[ 303.979219] 8eef5d00 8ef62b40 8fea7300 8f137918 00000000 00000000 0002bb01 793e5664
[ 303.987568] 8ef08884 00000001 8fea7300 00000002 8fc19e80 8eef5d00 00000006 00000003
[ 303.995934] 00000000 8030ba90 00000003 77ab3fd0 8149dc80 8004d1bc 8f15c000 8f383700
[ 304.004324] ...
[ 304.006767] Call Trace:
[ 304.009241] [<802cc920>] skb_panic+0x58/0x5c
[ 304.013504] [<802cd2a4>] skb_push+0x78/0x90
[ 304.017783] [<8f137918>] 0x8f137918
[ 304.021269] Code: 00602825 0c02a3b4 24842888 <000c000d> 8c870060 8c8200a0 0007382b 00070336 8c88005c
[ 304.031034]
[ 304.032805] ---[ end trace b778c482b3f0bda9 ]---
[ 304.041384] Kernel panic - not syncing: Fatal exception in interrupt
[ 304.051975] Rebooting in 3 seconds..
While the oops is for a 4.9-kernel, I was able to trigger the same oops with
net-next as of yesterday.
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7fd078337201cf7468f53c3d9ef81ff78cb6df3b ]
A CDC Ethernet functional descriptor with wMaxSegmentSize = 0 will
cause a divide error in usbnet_probe:
divide error: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc8-44453-g1fdc1a82c34f #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bef5c00 task.stack: ffff88006bf60000
RIP: 0010:usbnet_update_max_qlen+0x24d/0x390 drivers/net/usb/usbnet.c:355
RSP: 0018:ffff88006bf67508 EFLAGS: 00010246
RAX: 00000000000163c8 RBX: ffff8800621fce40 RCX: ffff8800621fcf34
RDX: 0000000000000000 RSI: ffffffff837ecb7a RDI: ffff8800621fcf34
RBP: ffff88006bf67520 R08: ffff88006bef5c00 R09: ffffed000c43f881
R10: ffffed000c43f880 R11: ffff8800621fc406 R12: 0000000000000003
R13: ffffffff85c71de0 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88006ca00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffe9c0d6dac CR3: 00000000614f4000 CR4: 00000000000006f0
Call Trace:
usbnet_probe+0x18b5/0x2790 drivers/net/usb/usbnet.c:1783
qmi_wwan_probe+0x133/0x220 drivers/net/usb/qmi_wwan.c:1338
usb_probe_interface+0x324/0x940 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x522/0x740 drivers/base/dd.c:557
Fix by simply ignoring the bogus descriptor, as it is optional
for QMI devices anyway.
Fixes: 423ce8caab7e ("net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2cb80187ba065d7decad7c6614e35e07aec8a974 ]
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b5f862180d7011d9575d0499fa37f0f25b423b12 ]
After commit 07f4c90062f8 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 18129a24983906eaf2a2d448ce4b83e27091ebe2 ]
FRA_L3MDEV is defined as U8, but is being added as a U32 attribute. On
big endian architecture, this results in the l3mdev entry not being
added to the FIB rules.
Fixes: 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|