summaryrefslogtreecommitdiff
path: root/drivers/regulator
AgeCommit message (Collapse)Author
2010-12-08ENGR00136146-2 MX53 TO2 ARD: Changed R2 value for reulator SW2 and LDO2Nancy Chen
LTC3589: Changed R2 value for reulator SW2 and LDO2. Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com>
2010-10-15ENGR00124788-1 Add Linear PMIC supportNancy Chen
Add Linear PMIC support. Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com>
2010-10-15ENGR00126326-2 - MAX17135: Add support for temperature sensor monitoringDanny Nold
- MAX17135 re-architected: - Core functionality, including I2C access to the chip, moved into drivers/mfd/max17135-core.c - MAX17135 regulators registered via init() callback in plat-specific code. - All access to registers funnelled through max17135_reg_read/write() apis. - max17135.h moved from regulator/ folder into mfd/ folder. - Support for reading internal and external temperature via sysfs interface, consistent with lm-sensors hwmon interface. Signed-off-by: Danny Nold <dannynold@freescale.com>
2010-10-01ENGR00132250 - MAX17135: dynamically detect polarity of PWRGOOD signalDanny Nold
We have multiple extension boards with some using positive polarity (EPD boards) and others using negative polarity (E-book add-on boards). Thus, we need to dynamically detect the polarity of this signal and factor it in later when testing whether power is good. Signed-off-by: Danny Nold <dannynold@freescale.com>
2010-09-29ENGR00132011-2 - MAX17135: Update for kernel 2.6.35Danny Nold
- __setup() function moved into MAX17135 driver to resolve conflict between platforms using the same MAX17135 part. - Added code to setup timing parameters the first time that a new PMIC part is used Signed-off-by: Danny Nold <dannynold@freescale.com>
2010-09-25ENGR00131874-1 - MAX17135 updates for kernel 2.6.35 upgradeDanny Nold
Added function to determine if VCOM is enabled, which is required for 2.6.35 (otherwise code always assumes regulator is active and aborts attempts to enable it). Signed-off-by: Danny Nold <dannynold@freescale.com>
2010-09-25ENGR00131707-2 upgrade mc13892 regulator driver to 2.6.35Zhou Jingyu
upgrade mc13892 regulator driver to 2.6.35 mc13892 regulator driver code Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
2010-09-25ENGR00126327-2 - Max17135 EPD PMIC: Support Pass 2 and VCOM settingDanny Nold
Add support for platform-level selection of PMIC pass version. 1 and 2 supported currently. Also support platform-level selection of VCOM voltage value. Signed-off-by: Danny Nold <dannynold@freescale.com>
2010-09-25ENGR00131832-2 MX25: Upgrade kernel to 2.6.35Alan Tull
This patch contains driver fixes for mx25. Contains all checkpatch and copyright fixes. Signed-off-by: Alan Tull <r80115@freescale.com>
2010-09-01ENGR00126692-3: Upgrade kernel to 2.6.35Dinh Nguyen
This patch contains changes to /drivers files Contains all checkpatch and copyright fixes. Acked-by: Rob Herring <r.herring@freescale.com> Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
2010-07-28regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH registerAnuj Aggarwal
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> In TPS6507x, depending on the status of DEFDCDC{2,3} pin either DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or programmed to change the output voltage. The current driver assumes DEFDCDC{2,3} pins are always tied low and thus operates only on DEFDCDC{2,3}_LOW register. This need not always be the case (as is found on OMAP-L138 EVM). Unfortunately, software cannot read the status of DEFDCDC{2,3} pins. So, this information is passed through platform data depending on how the board is wired. Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-07-27wm8350-regulator: fix wm8350_register_regulator error handlingAxel Lin
In the case of platform_device_add() fail, we should call platform_device_put() instead of platform_device_del() Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-07-27ab3100: fix off-by-one value range checking for voltage selectorAxel Lin
We use voltage selector as an array index for typ_voltages. Thus the valid range for voltage selector should be 0..voltages_len-1. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-06-03i2c: Remove all i2c_set_clientdata(client, NULL) in driversWolfram Sang
I2C drivers can use the clientdata-pointer to point to private data. As I2C devices are not really unregistered, but merely detached from their driver, it used to be the drivers obligation to clear this pointer during remove() or a failed probe(). As a couple of drivers forgot to do this, it was agreed that it was cleaner if the i2c-core does this clearance when appropriate, as there is no guarantee for the lifetime of the clientdata-pointer after remove() anyhow. This feature was added to the core with commit e4a7b9b04de15f6b63da5ccdd373ffa3057a3681 to fix the faulty drivers. As there is no need anymore to clear the clientdata-pointer, remove all current occurrences in the drivers to simplify the code and prevent confusion. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Acked-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-05-28mfd: AB3100 register access change to abx500 APIMattias Wallin
The interface for the AB3100 is changed to make way for the ABX500 family of chips: AB3550, AB5500 and future ST-Ericsson Analog Baseband chips. The register access functions are moved out to a separate struct abx500_ops. In this way the interface is moved from the implementation and the sub functionality drivers can keep their interface intact when chip infrastructure and communication mechanisms changes. We also define the AB3550 device IDs and the AB3550 platform data struct and convert the catenated 32bit event to an array of 3 x 8bits. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-05-28mfd: Renamed ab3100.h to abx500.hLinus Walleij
The goal here is to make way for a more general interface for the analog baseband chips ab3100 ab3550 ab550 and future chips. This patch have been divided into two parts since both changing name and content of a file is not recommended in git. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-05-28mfd: Add TPS6507x supportTodd Fischer
TPS6507x are multi function (PM, touchscreen) chipsets from TI. This commit also changes the corresponding regulator driver from being standalone to an MFD subdevice. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-05-28regulator: tps6057x namespace cleanupTodd Fischer
Move from using tps or tsp6507x to tps6057x_pmic in a consistent manner. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-05-28mfd: Add tps6507x board data structureTodd Fischer
Add mfd structure which refrences sub-driver initialization data. For example, for a giving hardware implementation, the voltage regulator sub-driver initialization data provides the mapping betten a voltage regulator and what the output voltage is being used for. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-05-28mfd: Move TPS6507x register definition to header file.Todd Fischer
Other sub-drivers for the TPS6507x chip will need to use register definition so move it out of the source file and into a header file. Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-05-25regulator: return set_mode is same mode is requestedSundar R Iyer
On Mon, 2010-05-17 at 17:34 +0200, Mark Brown wrote: > This doesn't seem like the right error handling - if the driver has a > set_mode() you'd *expect* it to have a get_mode() but there's no need > for it to be a strict requirement. True. In such a case, even a valid request would be lost! So now in the updated patch: - check if get_mode is present to avoid oops; - if get_mode is not present, proceed anyways for the request. Here is the updated patch: >From bad0d5eb51ef84be5b100e3dd0f5a590ea0529b6 Mon Sep 17 00:00:00 2001 From: Sundar R Iyer <sundar.iyer@stericsson.com> Date: Fri, 14 May 2010 15:14:17 +0530 Subject: [PATCH 1/1] regulator: return set_mode when same mode is requested save I/O costs by returning when the same mode is requested for the regulator Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25Regulators: ab3100/bq24022: add a missing .owner field in regulator_descAxel Lin
This patch adds a missing .owner field in regulator_desc, which is used for refcounting. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25twl6030: regulator: Remove vsel tables and use formula for calculationRajendra Nayak
All twl6030 regulators can be programmed from 1.0v to 3.3v with 100mV steps. The below formula can be used to calculate the vsel values to be programmed in the VREG_VOLTAGE registers. Voltage(in mV) = 1000mv + 100mv * (vsel - 1) Ex: if vsel = 0x9, mV = 1000 + 100 * (9 -1) = 1800mV. This patch removes all existing VSEL tables for twl6030 adjustable regulators and just uses the formula directly for vsel calculations after verifing they fall in the allowed range. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25mc13783-regulator: fix vaild voltage range checking for ↵Axel Lin
mc13783_fixed_regulator_set_voltage In the case of "min_uV == max_uV == mc13783_regulators[id].voltages[0]", mc13783_fixed_regulator_set_voltage should return 0 instead of -EINVAL. This patch also adds a missing ">" character for MODULE_AUTHOR, a trivial fix. Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25regulator: use voltage number array in 88pm860xHaojian Zhuang
A lot of condition comparision statements are used in original driver. These statements are used to check the boundary of voltage numbers since voltage number isn't linear. Now use array of voltage numbers instead. Clean code with simpler way. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25regulator: make 88pm860x sharing one driver structureHaojian Zhuang
Remove a lot of driver structures in 88pm860x driver. Make regulators share one driver structure. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25regulator: simplify regulator_register() error handlingJani Nikula
Simply remove all consumer supplies for the regulator on errors. Remove unset_consumer_device_supply() which is no longer used. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25regulator: fix unset_regulator_supplies() to remove all matchesJani Nikula
Remove all matching consumer supplies, not just the first, to not leave dangling pointers. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25regulator: prevent registration of matching regulator consumer suppliesJani Nikula
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Pointer comparison is not sufficient for non-NULL device name matching, so use strcmp(). Otherwise the semantics remain the same. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-25regulator: Allow regulator-regulator supplies to be specified by nameMark Brown
When one regulator supplies another allow the relationship to be specified using names rather than struct regulators, in a similar manner to that allowed for consumer supplies. This allows static configuration at compile time, reducing the need for dynamic init code. Also change the references to LINE supply to be system supply since line is sometimes used for actual supplies and therefore potentially confusing. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-20Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits) vlynq: make whole Kconfig-menu dependant on architecture add descriptive comment for TIF_MEMDIE task flag declaration. EEPROM: max6875: Header file cleanup EEPROM: 93cx6: Header file cleanup EEPROM: Header file cleanup agp: use NULL instead of 0 when pointer is needed rtc-v3020: make bitfield unsigned PCI: make bitfield unsigned jbd2: use NULL instead of 0 when pointer is needed cciss: fix shadows sparse warning doc: inode uses a mutex instead of a semaphore. uml: i386: Avoid redefinition of NR_syscalls fix "seperate" typos in comments cocbalt_lcdfb: correct sections doc: Change urls for sparse Powerpc: wii: Fix typo in comment i2o: cleanup some exit paths Documentation/: it's -> its where appropriate UML: Fix compiler warning due to missing task_struct declaration UML: add kernel.h include to signal.c ...
2010-04-28regulator: fix enabling regulator issue on max8925Haojian Zhuang
Fix regulator enabling issue that is caused by typo error in is_enabled(). Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23Merge branch 'master' into for-nextJiri Kosina
2010-04-19mc13783-regulator: fix a memory leak in mc13783_regulator_removeAxel Lin
This patch fixes a memory leak by freeing priv in mc13783_regulator_remove Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-22regulator: fix dangling pointersWolfram Sang
Fix I2C-drivers which missed setting clientdata to NULL before freeing the structure it points to. Also fix drivers which do this _after_ the structure was freed already. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22lp3971: Fix BUCK_VOL_CHANGE_SHIFT logicAxel Lin
Given x=0,1,2, current implementation of BUCK_VOL_CHANGE_SHIFT(x) returns 0,4,8. The correct return value should be 0,4,6. This patch fix the logic. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22lp3971: Fix setting val for LDO2 and LDO4Axel Lin
In lp3971_ldo_set_voltage function, it requires val to left shift 4 bits for LDO2 and LDO4. This patch fix this issue. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22regulator: Get rid of lockdep warningAmeya Palande
WARNING: at kernel/lockdep.c:2706 sysfs_add_file_mode+0x4c/0xa8() Difference between v1 and v2: Moved sysfs_attr_init() call as first one to access the structure. Signed-off-by: Ameya Palande <ameya.palande@nokia.com> CC: Liam Girdwood <lrg@slimlogic.co.uk> CC: Mark Brown <broonie@opensource.wolfsonmicro.com> CC: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22regulator: handle kcalloc() failureDan Carpenter
Return -ENOMEM if kcalloc() fails Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22Regulators: max8925-regulator - clean up driver data after removalDmitry Torokhov
It is a good tone to reset driver data after unbinding the device. Also change find_regulator_info() fro inline to __devinit - let compiler figure out if it wants it to be inlined or not. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-16Fix typos in commentsThomas Weber
[Ss]ytem => [Ss]ystem udpate => update paramters => parameters orginal => original Signed-off-by: Thomas Weber <swirl@gmx.li> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-03-07regulator: Add max8925 supportHaojian Zhuang
MAX8925 contains 3 Buck and 20 LDO regulator. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07regulator: Unsupport 88pm8607 A0 and A1Haojian Zhuang
Remove the support 88PM8607 A0/A1 stepping. There's some register definition changes in B0 stepping. It can make software more efficient. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Rename 88pm8607 to 88pm860x in mfdHaojian Zhuang
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Support 88pm8606 in 860x driverHaojian Zhuang
88PM8606 and 88PM8607 are two discrete chips used for power management. Hardware designer can use them together or only one of them according to requirement. There's some logic tightly linked between these two chips. For example, USB charger driver needs to access both chips by I2C interface. Now share one driver to these two devices. Only one I2C client is identified in platform init data. If another chip is also used, user should mark it in companion_addr field of platform init data. Then driver could create another I2C client for the companion chip. All I2C operations are accessed by 860x-i2c driver. In order to support both I2C client address, the read/write API is changed in below. reg_read(client, offset) reg_write(client, offset, data) The benefit is that client drivers only need one kind of read/write API. I2C and MFD driver can be shared in both 8606 and 8607. Since API is changed, update API in 8607 regulator driver. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07mfd: Add a data argument to the WM8350 IRQ free functionMark Brown
To better match genirq. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-03Regulators: wm8400 - cleanup platform driver data handlingDmitry Torokhov
On Wed, Feb 24, 2010 at 08:40:56PM +0000, Mark Brown wrote: > On Wed, Feb 24, 2010 at 11:21:26AM -0800, Dmitry Torokhov wrote: > > On Wed, Feb 24, 2010 at 07:14:03PM +0000, Mark Brown wrote: > > > > This doesn't help unless you also provide a way for users to obtain a > > > struct wm8400. > > > Why would they need it? Only code that creates instances of wm8400 needs > > to know the definition of the sturcture, the rest can simply pass the > > pointer around. > > > I guess there is disconnect between us and I do not see any users of > > wm8400_register_regulator() in linux-next... Is there another tree I > > could peek at? > > There are no users in mainline. This would be called by board specific > code from the init callback of the wm8400 - you'd need to pass that > callback the struct wm8400. > > In any case, this is clearly an unrelated change to whatever else you > were doing to the driver so should be split off into a separate patch, > but if this is being changed at all then it'd be much more sensible to > change it to use a more modern pattern which completely removes the > wm8400_register_regulator() function and just uses platform data. Fair enough, I removed the offending part, updated patch below. -- Dmitry regulator: wm8400 - cleanup platform driver data handling Driver data set by platform_set_drvdata() is for private use of the driver currently bound to teh device and not for use by parent, subsystem and anyone else. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-03Regulators: wm8994 - clean up driver data after removalDmitry Torokhov
It is a good tone to reset driver data after unbinding the device. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-03Regulators: wm831x-xxx - clean up driver data after removalDmitry Torokhov
It is a good tone to reset driver data after unbinding the device. Also set up drivers owner. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>