| Age | Commit message (Collapse) | Author |
|---|
|
commit 59c816c1f24df0204e01851431d3bab3eb76719c upstream.
This code in vhost_scsi_make_tpg() is confusing because we limit "tpgt"
to UINT_MAX but the data type of "tpg->tport_tpgt" and that is a u16.
I looked at the context and it turns out that in
vhost_scsi_set_endpoint(), "tpg->tport_tpgt" is used as an offset into
the vs_tpg[] array which has VHOST_SCSI_MAX_TARGET (256) elements so
anything higher than 255 then it is invalid. I have made that the limit
now.
In vhost_scsi_send_evt() we mask away values higher than 255, but now
that the limit has changed, we don't need the mask.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Ray Yang <ray.yang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be32c0cf0462c36f482b5ddcff1d8371be1e183c upstream.
The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96a5d18bc1338786fecac73599f1681f59a59a8e upstream.
The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8a9d66d043ffac116100775a469f05f5158c16f upstream.
After commit 566c09c53455 ("raid5: relieve lock contention in get_active_stripe()")
__find_stripe() is called under conf->hash_locks + hash.
But handle_stripe_clean_event() calls remove_hash() under
conf->device_lock.
Under some cirscumstances the hash chain can be circuited,
and we get an infinite loop with disabled interrupts and locked hash
lock in __find_stripe(). This leads to hard lockup on multiple CPUs
and following system crash.
I was able to reproduce this behavior on raid6 over 6 ssd disks.
The devices_handle_discard_safely option should be set to enable trim
support. The following script was used:
for i in `seq 1 32`; do
dd if=/dev/zero of=large$i bs=10M count=100 &
done
neilb: original was against a 3.x kernel. I forward-ported
to 4.3-rc. This verison is suitable for any kernel since
Commit: 59fc630b8b5f ("RAID5: batch adjacent full stripe write")
(v4.1+). I'll post a version for earlier kernels to stable.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Fixes: 566c09c53455 ("raid5: relieve lock contention in get_active_stripe()")
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org> # 3.13 - 4.2
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ca81a2840f77855bbad1b9f172c545c4dc9e6a4 upstream.
ib_send_cm_sidr_rep could sometimes erase the node from the sidr
(depending on errors in the process). Since ib_send_cm_sidr_rep is
called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv
could be either erased from the rb_tree twice or not erased at all.
Fixing that by making sure it's erased only once before freeing
cm_id_priv.
Fixes: a977049dacde ('[PATCH] IB: Add the kernel CM implementation')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2280521719e81919283b82902ac24058f87dfc1b upstream.
When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays
NULL but it's later used in mvs_abort_task as slot which is passed
to mvs_slot_task_free causing NULL pointer dereference.
Just return from mvs_slot_task_free when passed with NULL slot.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891
Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d01552a76d71f9879af448e9142389ee9be6e95b upstream.
This reverts commit 7eb418851f3278de67126ea0c427641ab4792c57.
This commit is poorly justified, I can find not discusison in email,
and it clearly causes a problem.
If a device which is being recovered fails and is subsequently
re-added to an array, there could easily have been changes to the
array *before* the point where the recovery was up to. So the
recovery must start again from the beginning.
If a spare is being recovered and fails, then when it is re-added we
really should do a bitmap-based recovery up to the recovery-offset,
and then a full recovery from there. Before this reversion, we only
did the "full recovery from there" which is not corect. After this
reversion with will do a full recovery from the start, which is safer
but not ideal.
It will be left to a future patch to arrange the two different styles
of recovery.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: 7eb418851f32 ("md: allow a partially recovered device to be hot-added to an array.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 681ab4696062f5aa939c9e04d058732306a97176 upstream.
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 203d27b0226a05202438ddb39ef0ef1acb14a759 upstream.
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a54c8f0f2d7df525ff997e2afe71866a1a013064 upstream.
xen-blkfront will crash if the check to talk_to_blkback()
in blkback_changed()(XenbusStateInitWait) returns an error.
The driver data is freed and info is set to NULL. Later during
the close process via talk_to_blkback's call to xenbus_dev_fatal()
the null pointer is passed to and dereference in blkfront_closing.
Signed-off-by: Cathy Avery <cathy.avery@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd7cd061adcf5f7503515ba52b6a724642a839c8 upstream.
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f317 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3d5 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b4739b8951d650becbcd855d7d6f18ac98a9a85 upstream.
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4dcb8b57df3593dcb20481d9d6cf79d1dc1534be upstream.
btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2871c69e025e8bc507651d5a9cf81a8a7da9d24b upstream.
Commit 4c7e309340ff ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().
The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them. If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.
Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.
Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d69bb536bac0d403d83db1ca841444981b280cd upstream.
Mapping an image with a long parent chain (e.g. image foo, whose parent
is bar, whose parent is baz, etc) currently leads to a kernel stack
overflow, due to the following recursion in the reply path:
rbd_osd_req_callback()
rbd_obj_request_complete()
rbd_img_obj_callback()
rbd_img_parent_read_callback()
rbd_obj_request_complete()
...
Limit the parent chain to 16 images, which is ~5K worth of stack. When
the above recursion is eliminated, this limit can be lifted.
Fixes: http://tracker.ceph.com/issues/12538
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
[idryomov@gmail.com: backport to 3.14: rbd_dev->opts, context]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f2c6651f69c14d0d3a9cfbda44ea101b02160ba upstream.
Currently we leak parent_spec and trigger a "parent reference
underflow" warning if rbd_dev_create() in rbd_dev_probe_parent() fails.
The problem is we take the !parent out_err branch and that only drops
refcounts; parent_spec that would've been freed had we called
rbd_dev_unparent() remains and triggers rbd_warn() in
rbd_dev_parent_put() - at that point we have parent_spec != NULL and
parent_ref == 0, so counter ends up being -1 after the decrement.
Redo rbd_dev_probe_parent() to fix this.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
[idryomov@gmail.com: backport to < 4.2: rbd_dev->opts]
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bae818ee1577c27356093901a0ea48f672eda514 upstream.
rbd requires stable pages, as it performs a crc of the page data before
they are send to the OSDs.
But since kernel 3.9 (patch 1d1d1a767206fbe5d4c69493b7e6d2a8d08cc0a0
"mm: only enforce stable page writes if the backing device requires
it") it is not assumed anymore that block devices require stable pages.
This patch sets the necessary flag to get stable pages back for rbd.
In a ceph installation that provides multiple ext4 formatted rbd
devices "bad crc" messages appeared regularly (ca 1 message every 1-2
minutes on every OSD that provided the data for the rbd) in the
OSD-logs before this patch. After this patch this messages are pretty
much gone (only ca 1-2 / month / OSD).
Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de>
[idryomov@gmail.com: require stable pages only in crc case, changelog]
[idryomov@gmail.com: backport to 3.9-3.17: context]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b94e22805a2224061bb263a82b72e09544a5fbb3 upstream.
0° Kelvin is actually −273.15°C, not -272.15°C. Fix the temperature offset.
Also improve the comment explaining the calculation.
Reported-by: Janusz Użycki <j.uzycki@elpromaelectronics.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49abb26651167c892393cd9f2ad23df429645ed9 upstream.
Fixes a harmless error message caused by:
51a4726b04e880fdd9b4e0e58b13f70b0a68a7f5
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e7a65aa70bcc1235a44e40ae0da5056525fe081 upstream.
We accidentally lost the initial DPLL register write in
1c4e02746147 drm/i915: Fix DVO 2x clock enable on 830M
The "three times for luck" hack probably saved us from a total
disaster. But anyway, bring the initial write back so that the
code actually makes some sense.
Reported-and-tested-by: Nick Bowler <nbowler@draconx.ca>
References: http://mid.gmane.org/CAN_QmVyMaArxYgEcVVsGvsMo7-6ohZr8HmF5VhkkL4i9KOmrhw@mail.gmail.com
Cc: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a6c521bb41ce862e43db46f52e7681d33e8d771 upstream.
On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.
This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1bde3b11fedace5042f0232339da90bc85666af upstream.
Fix the pointer-integer size mismatch warning below:
drivers/spi/spi-gpio.c: In function ‘spi_gpio_setup’:
drivers/spi/spi-gpio.c:252:8: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
cs = (unsigned int) spi->controller_data;
^
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31f50e48e3e4ea9d503285a389d6a1b5349d66c0 upstream.
This patch fixes following build warning:
In file included from include/linux/printk.h:261:0,
from include/linux/kernel.h:13,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/power/bq24190_charger.c:11:
drivers/power/bq24190_charger.c: In function ‘bq24190_irq_handler_thread’:
include/linux/dynamic_debug.h:86:20: warning: ‘ss_reg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
drivers/power/bq24190_charger.c:1211:5: note: ‘ss_reg’ was declared here
u8 ss_reg, f_reg;
^
In file included from include/linux/printk.h:261:0,
from include/linux/kernel.h:13,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/power/bq24190_charger.c:11:
include/linux/dynamic_debug.h:86:20: warning: ‘f_reg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
drivers/power/bq24190_charger.c:1211:13: note: ‘f_reg’ was declared here
u8 ss_reg, f_reg;
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d20a16062e771b6e26b843c0cde3b17c1146e00 upstream.
drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'. Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cbf3ccd09d683abf1cacd36e3640872ee912d99b upstream.
During device assignment/deassignment the flags in the DTE
get lost, which might cause spurious faults, for example
when the device tries to access the system management range.
Fix this by not clearing the flags with the rest of the DTE.
Reported-by: G. Richard Bellamy <rbellamy@pteradigm.com>
Tested-by: G. Richard Bellamy <rbellamy@pteradigm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f08f625876476b6c4a87834dc86e3b927f4697d2 upstream.
Add 3 new subdevice IDs for the 0x095A device ID and 2 for the 0x095B
device ID.
Reported-by: Jeremy <jeremy.bomkamp@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2cf5eb3ab7bb7f2e3a70edcef236cd62c87db030 upstream.
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5a48134f8af08f5243328f8a0b05fc5ae7cf343 upstream.
The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bd166872d8f99f156fac191299d24f828bb2348 upstream.
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 029cd0370241641eb70235d205aa0b90c84dce44 upstream.
ath9k inserts padding between the 802.11 header and the data area (to
align it). Since it didn't declare this extra required headroom, this
led to some nasty issues like randomly dropped packets in some setups.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ebe138ac642a195c7f2efdb918f464734421fd6 upstream.
If rbd_dev_image_probe() in rbd_dev_probe_parent() fails, header_name
is freed twice: once in rbd_dev_probe_parent() and then in its caller
rbd_dev_image_probe() (rbd_dev_image_probe() is called recursively to
handle parent images).
rbd_dev_probe_parent() is responsible for probing the parent, so it
shouldn't muck with clone's fields.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba30670f4d5292c4e7f7980bbd5071f7c4794cdd upstream.
Fixes: ac8c3f3df ("dm thin: generate event when metadata threshold passed")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 51a4726b04e880fdd9b4e0e58b13f70b0a68a7f5 upstream.
They were added relatively early in the driver init process
which meant that in some cases the driver was not finished
initializing before external tools tried to use them which
could result in a crash depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f231976c2e8964ceaa9250e57d27c35ff03825c2 upstream.
We need to do this in order to prevent accesses to the device while it's
powered down. Userspace may have an mmap of the fb, and there's no good
way (that I know of) to prevent it from touching the device otherwise.
This fixes some nasty races between runpm and plymouth on some systems,
which result in the GPU getting very upset and hanging the boot.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56d4b8a24cef5d66f0d10ac778a520d3c2c68a48 upstream.
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eadd709f5d2e8aebb1b7bf49460e97a68d81a9b0 upstream.
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f7effddf4549d57114289f273710f077c4c330a upstream.
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 436c2a5036b6ffe813310df2cf327d3b69be0734 ]
commit 3cc81d85ee01 ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3cc81d85ee01e5a0b7ea2f4190e2ed1165f53c31 ]
I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
ifconfig eth0 down
ethtool -s eth0 autoneg off speed 10 duplex half
ifconfig eth0 up
Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e6740165b8f7f06d8caee0fceab3fb9d790a6fed ]
Since commit 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"),
pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the
PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to
PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the
following oops:
[ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0
[ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0
[ 570.144601] Oops: 0000 [#1] SMP
[ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio
[ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1
[ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000
[ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202
[ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206
[ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20
[ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000
[ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780
[ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0
[ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000
[ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0
[ 570.144601] Stack:
[ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0
[ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008
[ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5
[ 570.144601] Call Trace:
[ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75
[ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11
[ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5
[ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb
[ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90
[ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7
[ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b
[ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f
[ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00
[ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] RSP <ffff880036b63e08>
[ 570.144601] CR2: 00000000000004e0
[ 570.200518] ---[ end trace 46956baf17349563 ]---
pppoe_flush_dev() has no reason to override sk->sk_state with
PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to
PPPOX_DEAD, which is the correct state given that sk is unbound and
po->pppoe_dev is NULL.
Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Tested-by: Oleksii Berezhniak <core@irc.lg.ua>
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15e3d5a285ab9283136dba34bbf72886d9146706 upstream.
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1d562acc78f0af46de0dfe447410bc40bdb7ece upstream.
Here is a patch to make speakup-r work again.
It broke in 3.6 due to commit 4369c64c79a22b98d3b7eff9d089196cd878a10a
"Input: Send events one packet at a time)
The problem was that the fakekey.c routine to fake a down arrow no
longer functioned properly and putting the input_sync fixed it.
Fixes: 4369c64c79a22b98d3b7eff9d089196cd878a10a
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bffa1503c5c06192eb1459180fac4416575a966 upstream.
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19e79687de22f23bcfb5e79cce3daba20af228d1 upstream.
On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.
This solves the following oops:
[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c
Fixes: aafd900cab87 ("CLK: TI: add omap3 clock init file")
Cc: mturquette@baylibre.com
Cc: sboyd@codeaurora.org
Cc: linux-clk@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c7feb2ebfc9c0552c51f0c050db1d1a004faac5 upstream.
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 281fda27673f833a01d516658a64d22a32c8e072 upstream.
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee5d004fd0591536a061451eba2b187092e9127c upstream.
The 'event_work' worker used by dm-raid may still be running
when the array is stopped. This can result in an oops.
So flush the workqueue on which it is run after detaching
and before destroying the device.
Reported-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: 9d09e663d550 ("dm: raid456 basic support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c04a1f17803e0d3eeada586ca34a6b436959bc20 upstream.
`devpriv->ao_timer` is used while an asynchronous command is running on
the AO subdevice. It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands,
`usbduxsigma_ao_cmdtest()`, which is not correct as it's allowed to
check new commands while an old command is still running. Fix it by
moving the code which sets up `devpriv->ao_timer` into the subdevice's
`cmd` handler, `usbduxsigma_ao_cmd()`.
Note that the removed code in `usbduxsigma_ao_cmdtest()` checked that
`devpriv->ao_timer` did not end up less that 1, but that could not
happen due because `cmd->scan_begin_arg` or `cmd->convert_arg` had
already been range-checked.
Also note that we tested the `high_speed` variable in the old code, but
that is currently always 0 and means that we always use "scan" timing
(`cmd->scan_begin_src == TRIG_TIMER` and `cmd->convert_src == TRIG_NOW`)
and never "convert" (individual sample) timing (`cmd->scan_begin_src ==
TRIG_FOLLOW` and `cmd->convert_src == TRIG_TIMER`). The moved code
tests `cmd->convert_src` instead to decide whether "scan" or "convert"
timing is being used, although currently only "scan" timing is
supported.
Fixes: fb1ef622e7a3 ("staging: comedi: usbduxsigma: tidy up analog output command support")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Bernd Porr <mail@berndporr.me.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 423b24c37dd5794a674c74b0ed56392003a69891 upstream.
`devpriv->ai_timer` is used while an asynchronous command is running on
the AI subdevice. It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands
(`usbduxsigma_ai_cmdtest()`), which is not correct as it's allowed to
check new commands while an old command is still running. Fix it by
moving the code which sets up `devpriv->ai_timer` and
`devpriv->ai_interval` into the subdevice's `cmd` handler,
`usbduxsigma_ai_cmd()`.
Note that the removed code in `usbduxsigma_ai_cmdtest()` checked that
`devpriv->ai_timer` did not end up less than than 1, but that could not
happen because `cmd->scan_begin_arg` had already been checked to be at
least the minimum required value (at least when `cmd->scan_begin_src ==
TRIG_TIMER`, which had also been checked to be the case).
Fixes: b986be8527c7 ("staging: comedi: usbduxsigma: tidy up analog input command support)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Bernd Porr <mail@berndporr.me.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8484bf2981b3d006426ac052a3642c9ce1d8d980 upstream.
These two headphones need a reset-resume quirk to properly resume to
original volume level.
Signed-off-by: Yao-Wen Mao <yaowen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
