summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2015-10-283w-9xxx: don't unmap bounce buffered commandsChristoph Hellwig
[ Upstream commit 15e3d5a285ab9283136dba34bbf72886d9146706 ] 3w controller don't dma map small single SGL entry commands but instead bounce buffer them. Add a helper to identify these commands and don't call scsi_dma_unmap for them. Based on an earlier patch from James Bottomley. Fixes: 118c85 ("3w-9xxx: fix command completion race") Reported-by: Tóth Attila <atoth@atoth.sote.hu> Tested-by: Tóth Attila <atoth@atoth.sote.hu> Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27md: flush ->event_work before stopping array.NeilBrown
[ Upstream commit ee5d004fd0591536a061451eba2b187092e9127c ] The 'event_work' worker used by dm-raid may still be running when the array is stopped. This can result in an oops. So flush the workqueue on which it is run after detaching and before destroying the device. Reported-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com> Cc: stable@vger.kernel.org (2.6.38+ please delay 2 weeks after -final release) Fixes: 9d09e663d550 ("dm: raid456 basic support") Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27Revert "iio: bmg160: IIO_BUFFER and IIO_TRIGGERED_BUFFER are required"Markus Pargmann
[ Upstream commit HEAD ] This reverts commit 279c039ca63acbd69e69d6d7ddfed50346fb2185 which was commit 06d2f6ca5a38abe92f1f3a132b331eee773868c3 upstream as it should not have been applied. Reported-by: Luis Henriques <luis.henriques@canonical.com> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (cherry picked from commit 934d9b907aeec5f344ca801ed7361551199dfc69) Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27mm: check if section present during memory block registeringYinghai Lu
[ Upstream commit 04697858d89e4bf2650364f8d6956e2554e8ef88 ] Tony Luck found on his setup, if memory block size 512M will cause crash during booting. BUG: unable to handle kernel paging request at ffffea0074000020 IP: get_nid_for_pfn+0x17/0x40 PGD 128ffcb067 PUD 128ffc9067 PMD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.2.0-rc8 #1 ... Call Trace: ? register_mem_sect_under_node+0x66/0xe0 register_one_node+0x17b/0x240 ? pci_iommu_alloc+0x6e/0x6e topology_init+0x3c/0x95 do_one_initcall+0xcd/0x1f0 The system has non continuous RAM address: BIOS-e820: [mem 0x0000001300000000-0x0000001cffffffff] usable BIOS-e820: [mem 0x0000001d70000000-0x0000001ec7ffefff] usable BIOS-e820: [mem 0x0000001f00000000-0x0000002bffffffff] usable BIOS-e820: [mem 0x0000002c18000000-0x0000002d6fffefff] usable BIOS-e820: [mem 0x0000002e00000000-0x00000039ffffffff] usable So there are start sections in memory block not present. For example: memory block : [0x2c18000000, 0x2c20000000) 512M first three sections are not present. The current register_mem_sect_under_node() assume first section is present, but memory block section number range [start_section_nr, end_section_nr] would include not present section. For arch that support vmemmap, we don't setup memmap for struct page area within not present sections area. So skip the pfn range that belong to absent section. [akpm@linux-foundation.org: simplification] [rientjes@google.com: more simplification] Fixes: bdee237c0343 ("x86: mm: Use 2GB memory block size on large memory x86-64 systems") Fixes: 982792c782ef ("x86, mm: probe memory block size for generic x86 64bit") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Tony Luck <tony.luck@intel.com> Tested-by: Tony Luck <tony.luck@intel.com> Cc: Greg KH <greg@kroah.com> Cc: Ingo Molnar <mingo@elte.hu> Tested-by: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> [3.15+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27drivercore: Fix unregistration path of platform devicesGrant Likely
[ Upstream commit 7f5dcaf1fdf289767a126a0a5cc3ef39b5254b06 ] The unregister path of platform_device is broken. On registration, it will register all resources with either a parent already set, or type==IORESOURCE_{IO,MEM}. However, on unregister it will release everything with type==IORESOURCE_{IO,MEM}, but ignore the others. There are also cases where resources don't get registered in the first place, like with devices created by of_platform_populate()*. Fix the unregister path to be symmetrical with the register path by checking the parent pointer instead of the type field to decide which resources to unregister. This is safe because the upshot of the registration path algorithm is that registered resources have a parent pointer, and non-registered resources do not. * It can be argued that of_platform_populate() should be registering it's resources, and they argument has some merit. However, there are quite a few platforms that end up broken if we try to do that due to overlapping resources in the device tree. Until that is fixed, we need to solve the immediate problem. Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Rob Herring <robh@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Grant Likely <grant.likely@linaro.org> Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27of/address: Don't loop forever in of_find_matching_node_by_address().David Daney
[ Upstream commit 3a496b00b6f90c41bd21a410871dfc97d4f3c7ab ] If the internal call to of_address_to_resource() fails, we end up looping forever in of_find_matching_node_by_address(). This can be caused by a defective device tree, or calling with an incorrect matches argument. Fix by calling of_find_matching_node() unconditionally at the end of the loop. Signed-off-by: David Daney <david.daney@cavium.com> Cc: stable@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27auxdisplay: ks0108: fix refcountSudip Mukherjee
[ Upstream commit bab383de3b84e584b0f09227151020b2a43dc34c ] parport_find_base() will implicitly do parport_get_port() which increases the refcount. Then parport_register_device() will again increment the refcount. But while unloading the module we are only doing parport_unregister_device() decrementing the refcount only once. We add an parport_put_port() to neutralize the effect of parport_get_port(). Cc: <stable@vger.kernel.org> # 2.6.32+ Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27devres: fix devres_get()Masahiro Yamada
[ Upstream commit 64526370d11ce8868ca495723d595b61e8697fbf ] Currently, devres_get() passes devres_free() the pointer to devres, but devres_free() should be given with the pointer to resource data. Fixes: 9ac7849e35f7 ("devres: device resource management") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: stable <stable@vger.kernel.org> # 2.6.21+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27HID: usbhid: Fix the check for HID_RESET_PENDING in hid_io_errorDon Zickus
[ Upstream commit 3af4e5a95184d6d3c1c6a065f163faa174a96a1d ] It was reported that after 10-20 reboots, a usb keyboard plugged into a docking station would not work unless it was replugged in. Using usbmon, it turns out the interrupt URBs were streaming with callback errors of -71 for some reason. The hid-core.c::hid_io_error was supposed to retry and then reset, but the reset wasn't really happening. The check for HID_NO_BANDWIDTH was inverted. Fix was simple. Tested by reporter and locally by me by unplugging a keyboard halfway until I could recreate a stream of errors but no disconnect. Signed-off-by: Don Zickus <dzickus@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27serial: 8250: don't bind to SMSC IrCC IR portMaciej S. Szmigiero
[ Upstream commit ffa34de03bcfbfa88d8352942bc238bb48e94e2d ] SMSC IrCC SIR/FIR port should not be bound to by (legacy) serial driver so its own driver (smsc-ircc2) can bind to it. Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: host: ehci-sys: delete useless bus_to_hcd conversionPeter Chen
[ Upstream commit 0521cfd06e1ebcd575e7ae36aab068b38df23850 ] The ehci platform device's drvdata is the pointer of struct usb_hcd already, so we doesn't need to call bus_to_hcd conversion again. Cc: <stable@vger.kernel.org> Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: dwc3: ep0: Fix mem corruption on OUT transfers of more than 512 bytesKishon Vijay Abraham I
[ Upstream commit b2fb5b1a0f50d3ebc12342c8d8dead245e9c9d4e ] DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and the size of bounce buffer is 512 bytes. However if the host initiates OUT transfers of size more than 512 bytes (and non max packet aligned), the driver throws a WARN dump but still programs the TRB to receive more than 512 bytes. This will cause bounce buffer to overflow and corrupt the adjacent memory locations which can be fatal. Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE (512) bytes. Cc: <stable@vger.kernel.org> # 3.4+ Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27USB: ftdi_sio: Added custom PID for CustomWare productsMatthijs Kooijman
[ Upstream commit 1fb8dc36384ae1140ee6ccc470de74397606a9d5 ] CustomWare uses the FTDI VID with custom PIDs for their ShipModul MiniPlex products. Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27USB: symbolserial: Use usb_get_serial_port_dataPhilipp Hachtmann
[ Upstream commit 951d3793bbfc0a441d791d820183aa3085c83ea9 ] The driver used usb_get_serial_data(port->serial) which compiled but resulted in a NULL pointer being returned (and subsequently used). I did not go deeper into this but I guess this is a regression. Signed-off-by: Philipp Hachtmann <hachti@hachti.de> Fixes: a85796ee5149 ("USB: symbolserial: move private-data allocation to port_probe") Cc: stable <stable@vger.kernel.org> # v3.10 Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27PCI: Fix TI816X class code quirkBjorn Helgaas
[ Upstream commit d1541dc977d376406f4584d8eb055488655c98ec ] In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO". But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class and needs to be shifted to make space for the low-order interface byte. Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code. Fixes: 63c4408074cb ("PCI: Add quirk for setting valid class for TI816X Endpoint") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Hemant Pedanekar <hemantp@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27clk: versatile: off by one in clk_sp810_timerclken_of_get()Dan Carpenter
[ Upstream commit 3294bee87091be5f179474f6c39d1d87769635e2 ] The ">" should be ">=" or we end up reading beyond the end of the array. Fixes: 6e973d2c4385 ('clk: vexpress: Add separate SP810 driver') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27staging: comedi: adl_pci7x3x: fix digital output on PCI-7230Ian Abbott
[ Upstream commit ad83dbd974feb2e2a8cc071a1d28782bd4d2c70e ] The "adl_pci7x3x" driver replaced the "adl_pci7230" and "adl_pci7432" drivers in commits 8f567c373c4b ("staging: comedi: new adl_pci7x3x driver") and 657f77d173d3 ("staging: comedi: remove adl_pci7230 and adl_pci7432 drivers"). Although the new driver code agrees with the user manuals for the respective boards, digital outputs stopped working on the PCI-7230. This has 16 digital output channels and the previous adl_pci7230 driver shifted the 16 bit output state left by 16 bits before writing to the hardware register. The new adl_pci7x3x driver doesn't do that. Fix it in `adl_pci7x3x_do_insn_bits()` by checking for the special case of the subdevice having only 16 channels and duplicating the 16 bit output state into both halves of the 32-bit register. That should work both for what the board actually does and for what the user manual says it should do. Fixes: 8f567c373c4b ("staging: comedi: new adl_pci7x3x driver") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Cc: <stable@vger.kernel.org> # 3.13+, needs backporting for 3.7 to 3.12 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27iio: adis16480: Fix scale factorsLars-Peter Clausen
[ Upstream commit 7abad1063deb0f77d275c61f58863ec319c58c5c ] The different devices support by the adis16480 driver have slightly different scales for the gyroscope and accelerometer channels. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27iio: industrialio-buffer: Fix iio_buffer_poll return valueCristina Opriceana
[ Upstream commit 1bdc0293901cbea23c6dc29432e81919d4719844 ] Change return value to 0 if no device is bound since unsigned int cannot support negative error codes. Fixes: f18e7a068 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27iio: event: Remove negative error code from iio_event_pollCristina Opriceana
[ Upstream commit 41d903c00051d8f31c98a8136edbac67e6f8688f ] Negative return values are not supported by iio_event_poll since its return type is unsigned int. Fixes: f18e7a068a0a3 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27iio: bmg160: IIO_BUFFER and IIO_TRIGGERED_BUFFER are requiredMarkus Pargmann
[ Upstream commit 06d2f6ca5a38abe92f1f3a132b331eee773868c3 ] This patch adds selects for IIO_BUFFER and IIO_TRIGGERED_BUFFER. Without IIO_BUFFER, the driver does not compile. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27s390/sclp: fix compile errorSebastian Ott
[ Upstream commit a313bdc5310dd807655d3ca3eb2219cd65dfe45a ] Fix this error when compiling with CONFIG_SMP=n and CONFIG_DYNAMIC_DEBUG=y: drivers/s390/char/sclp_early.c: In function 'sclp_read_info_early': drivers/s390/char/sclp_early.c:87:19: error: 'EBUSY' undeclared (first use in this function) } while (rc == -EBUSY); ^ Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27drm/qxl: validate monitors config modesJonathon Jongsma
[ Upstream commit bd3e1c7c6de9f5f70d97cdb6c817151c0477c5e3 ] Due to some recent changes in drm_helper_probe_single_connector_modes_merge_bits(), old custom modes were not being pruned properly. In current kernels, drm_mode_validate_basic() is called to sanity-check each mode in the list. If the sanity-check passes, the mode's status gets set to to MODE_OK. In older kernels this check was not done, so old custom modes would still have a status of MODE_UNVERIFIED at this point, and would therefore be pruned later in the function. As a result of this new behavior, the list of modes for a device always includes every custom mode ever configured for the device, with the largest one listed first. Since desktop environments usually choose the first preferred mode when a hotplug event is emitted, this had the result of making it very difficult for the user to reduce the size of the display. The qxl driver did implement the mode_valid connector function, but it was empty. In order to restore the old behavior where old custom modes are pruned, we implement a proper mode_valid function for the qxl driver. This function now checks each mode against the last configured custom mode and the list of standard modes. If the mode doesn't match any of these, its status is set to MODE_BAD so that it will be pruned as expected. Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27drm/amdgpu: Don't link train DisplayPort on HPD until we get the dpcdStephen Chandler Paul
[ Upstream commit a887adadb7b9ef9eb4ee48e4ad575aefcfd1db14 ] This is a port of: DRM - radeon: Don't link train DisplayPort on HPD until we get the dpcd to amdgpu. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27intel_pstate: Fix overflow in busy_scaled due to long delayPrarit Bhargava
[ Upstream commit 7180dddf7c32c49975c7e7babf2b60ed450cb760 ] The kernel may delay interrupts for a long time which can result in timers being delayed. If this occurs the intel_pstate driver will crash with a divide by zero error: divide error: 0000 [#1] SMP Modules linked in: btrfs zlib_deflate raid6_pq xor msdos ext4 mbcache jbd2 binfmt_misc arc4 md4 nls_utf8 cifs dns_resolver tcp_lp bnep bluetooth rfkill fuse dm_service_time iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ftp ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables intel_powerclamp coretemp vfat fat kvm_intel iTCO_wdt iTCO_vendor_support ipmi_devintf sr_mod kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel cdc_ether lrw usbnet cdrom mii gf128mul glue_helper ablk_helper cryptd lpc_ich mfd_core pcspkr sb_edac edac_core ipmi_si ipmi_msghandler ioatdma wmi shpchp acpi_pad nfsd auth_rpcgss nfs_acl lockd uinput dm_multipath sunrpc xfs libcrc32c usb_storage sd_mod crc_t10dif crct10dif_common ixgbe mgag200 syscopyarea sysfillrect sysimgblt mdio drm_kms_helper ttm igb drm ptp pps_core dca i2c_algo_bit megaraid_sas i2c_core dm_mirror dm_region_hash dm_log dm_mod CPU: 113 PID: 0 Comm: swapper/113 Tainted: G W -------------- 3.10.0-229.1.2.el7.x86_64 #1 Hardware name: IBM x3950 X6 -[3837AC2]-/00FN827, BIOS -[A8E112BUS-1.00]- 08/27/2014 task: ffff880fe8abe660 ti: ffff880fe8ae4000 task.ti: ffff880fe8ae4000 RIP: 0010:[<ffffffff814a9279>] [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP: 0018:ffff883fff4e3db8 EFLAGS: 00010206 RAX: 0000000027100000 RBX: ffff883fe6965100 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000010 RDI: 000000002e53632d RBP: ffff883fff4e3e20 R08: 000e6f69a5a125c0 R09: ffff883fe84ec001 R10: 0000000000000002 R11: 0000000000000005 R12: 00000000000049f5 R13: 0000000000271000 R14: 00000000000049f5 R15: 0000000000000246 FS: 0000000000000000(0000) GS:ffff883fff4e0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7668601000 CR3: 000000000190a000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffff883fff4e3e58 ffffffff81099dc1 0000000000000086 0000000000000071 ffff883fff4f3680 0000000000000071 fbdc8a965e33afee ffffffff810b69dd ffff883fe84ec000 ffff883fe6965108 0000000000000100 ffffffff814a9100 Call Trace: <IRQ> [<ffffffff81099dc1>] ? run_posix_cpu_timers+0x51/0x840 [<ffffffff810b69dd>] ? trigger_load_balance+0x5d/0x200 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107df56>] call_timer_fn+0x36/0x110 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107fdcf>] run_timer_softirq+0x21f/0x320 [<ffffffff81077b2f>] __do_softirq+0xef/0x280 [<ffffffff816156dc>] call_softirq+0x1c/0x30 [<ffffffff81015d95>] do_softirq+0x65/0xa0 [<ffffffff81077ec5>] irq_exit+0x115/0x120 [<ffffffff81616355>] smp_apic_timer_interrupt+0x45/0x60 [<ffffffff81614a1d>] apic_timer_interrupt+0x6d/0x80 <EOI> [<ffffffff814a9c32>] ? cpuidle_enter_state+0x52/0xc0 [<ffffffff814a9c28>] ? cpuidle_enter_state+0x48/0xc0 [<ffffffff814a9d65>] cpuidle_idle_call+0xc5/0x200 [<ffffffff8101d14e>] arch_cpu_idle+0xe/0x30 [<ffffffff810c67c1>] cpu_startup_entry+0xf1/0x290 [<ffffffff8104228a>] start_secondary+0x1ba/0x230 Code: 42 0f 00 45 89 e6 48 01 c2 43 8d 44 6d 00 39 d0 73 26 49 c1 e5 08 89 d2 4d 63 f4 49 63 c5 48 c1 e2 08 48 c1 e0 08 48 63 ca 48 99 <48> f7 f9 48 98 4c 0f af f0 49 c1 ee 08 8b 43 78 c1 e0 08 44 29 RIP [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP <ffff883fff4e3db8> The kernel values for cpudata for CPU 113 were: struct cpudata { cpu = 113, timer = { entry = { next = 0x0, prev = 0xdead000000200200 }, expires = 8357799745, base = 0xffff883fe84ec001, function = 0xffffffff814a9100 <intel_pstate_timer_func>, data = 18446612406765768960, <snip> i_gain = 0, d_gain = 0, deadband = 0, last_err = 22489 }, last_sample_time = { tv64 = 4063132438017305 }, prev_aperf = 287326796397463, prev_mperf = 251427432090198, sample = { core_pct_busy = 23081, aperf = 2937407, mperf = 3257884, freq = 2524484, time = { tv64 = 4063149215234118 } } } which results in the time between samples = last_sample_time - sample.time = 4063149215234118 - 4063132438017305 = 16777216813 which is 16.777 seconds. The duration between reads of the APERF and MPERF registers overflowed a s32 sized integer in intel_pstate_get_scaled_busy()'s call to div_fp(). The result is that int_tofp(duration_us) == 0, and the kernel attempts to divide by 0. While the kernel shouldn't be delaying for a long time, it can and does happen and the intel_pstate driver should not panic in this situation. This patch changes the div_fp() function to use div64_s64() to allow for "long" division. This will avoid the overflow condition on long delays. [v2]: use div64_s64() in div_fp() Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.cKosuke Tatsukawa
[ Upstream commit e81107d4c6bd098878af9796b24edc8d4a9524fd ] My colleague ran into a program stall on a x86_64 server, where n_tty_read() was waiting for data even if there was data in the buffer in the pty. kernel stack for the stuck process looks like below. #0 [ffff88303d107b58] __schedule at ffffffff815c4b20 #1 [ffff88303d107bd0] schedule at ffffffff815c513e #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23 #5 [ffff88303d107dd0] tty_read at ffffffff81368013 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57 #8 [ffff88303d107f00] sys_read at ffffffff811a4306 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7 There seems to be two problems causing this issue. First, in drivers/tty/n_tty.c, __receive_buf() stores the data and updates ldata->commit_head using smp_store_release() and then checks the wait queue using waitqueue_active(). However, since there is no memory barrier, __receive_buf() could return without calling wake_up_interactive_poll(), and at the same time, n_tty_read() could start to wait in wait_woken() as in the following chart. __receive_buf() n_tty_read() ------------------------------------------------------------------------ if (waitqueue_active(&tty->read_wait)) /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ add_wait_queue(&tty->read_wait, &wait); ... if (!input_available_p(tty, 0)) { smp_store_release(&ldata->commit_head, ldata->read_head); ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ The second problem is that n_tty_read() also lacks a memory barrier call and could also cause __receive_buf() to return without calling wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken() as in the chart below. __receive_buf() n_tty_read() ------------------------------------------------------------------------ spin_lock_irqsave(&q->lock, flags); /* from add_wait_queue() */ ... if (!input_available_p(tty, 0)) { /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ smp_store_release(&ldata->commit_head, ldata->read_head); if (waitqueue_active(&tty->read_wait)) __add_wait_queue(q, wait); spin_unlock_irqrestore(&q->lock,flags); /* from add_wait_queue() */ ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ There are also other places in drivers/tty/n_tty.c which have similar calls to waitqueue_active(), so instead of adding many memory barrier calls, this patch simply removes the call to waitqueue_active(), leaving just wake_up*() behind. This fixes both problems because, even though the memory access before or after the spinlocks in both wake_up*() and add_wait_queue() can sneak into the critical section, it cannot go past it and the critical section assures that they will be serialized (please see "INTER-CPU ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a better explanation). Moreover, the resulting code is much simpler. Latency measurement using a ping-pong test over a pty doesn't show any visible performance drop. Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27staging: speakup: fix speakup-r regressioncovici@ccs.covici.com
[ Upstream commit b1d562acc78f0af46de0dfe447410bc40bdb7ece ] Here is a patch to make speakup-r work again. It broke in 3.6 due to commit 4369c64c79a22b98d3b7eff9d089196cd878a10a "Input: Send events one packet at a time) The problem was that the fakekey.c routine to fake a down arrow no longer functioned properly and putting the input_sync fixed it. Fixes: 4369c64c79a22b98d3b7eff9d089196cd878a10a Cc: stable <stable@vger.kernel.org> Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: John Covici <covici@ccs.covici.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27dm cache: fix NULL pointer when switching from cleaner policyJoe Thornber
[ Upstream commit 2bffa1503c5c06192eb1459180fac4416575a966 ] The cleaner policy doesn't make use of the per cache block hint space in the metadata (unlike the other policies). When switching from the cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block) was observed. The crash was caused by bugs in dm-cache-metadata.c when trying to skip creation of the hint btree. The minimal fix is to change hint size for the cleaner policy to 4 bytes (only hint size supported). Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27clk: ti: fix dual-registration of uart4_ickBen Dooks
[ Upstream commit 19e79687de22f23bcfb5e79cce3daba20af228d1 ] On the OMAP AM3517 platform the uart4_ick gets registered twice, causing any power management to /dev/ttyO3 to fail when trying to wake the device up. This solves the following oops: [] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008 [] PC is at serial_omap_pm+0x48/0x15c [] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c Fixes: aafd900cab87 ("CLK: TI: add omap3 clock init file") Cc: stable@vger.kernel.org Cc: mturquette@baylibre.com Cc: sboyd@codeaurora.org Cc: linux-clk@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-kernel@lists.codethink.co.uk Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27igb: do not re-init SR-IOV during probeStefan Assmann
[ Upstream commit 6423fc34160939142d72ffeaa2db6408317f54df ] During driver probing the following code path is triggered. igb_probe ->igb_sw_init ->igb_probe_vfs ->igb_pci_enable_sriov ->igb_sriov_reinit Doing the SR-IOV re-init is not necessary during probing since we're starting from scratch. Here we can call igb_enable_sriov() right away. Running igb_sriov_reinit() during igb_probe() also seems to cause occasional packet loss on some onboard 82576 NICs. Reproduced on Dell and HP servers with onboard 82576 NICs. Example: Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01) Subsystem: Dell Device [1028:0481] Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27net/xen-netfront: only napi_synchronize() if runningChas Williams
[ Upstream commit 274b045509175db0405c784be85e8cce116e6f7d ] If an interface isn't running napi_synchronize() will hang forever. [ 392.248403] rmmod R running task 0 359 343 0x00000000 [ 392.257671] ffff88003760fc88 ffff880037193b40 ffff880037193160 ffff88003760fc88 [ 392.267644] ffff880037610000 ffff88003760fcd8 0000000100014c22 ffffffff81f75c40 [ 392.277524] 0000000000bc7010 ffff88003760fca8 ffffffff81796927 ffffffff81f75c40 [ 392.287323] Call Trace: [ 392.291599] [<ffffffff81796927>] schedule+0x37/0x90 [ 392.298553] [<ffffffff8179985b>] schedule_timeout+0x14b/0x280 [ 392.306421] [<ffffffff810f91b9>] ? irq_free_descs+0x69/0x80 [ 392.314006] [<ffffffff811084d0>] ? internal_add_timer+0xb0/0xb0 [ 392.322125] [<ffffffff81109d07>] msleep+0x37/0x50 [ 392.329037] [<ffffffffa00ec79a>] xennet_disconnect_backend.isra.24+0xda/0x390 [xen_netfront] [ 392.339658] [<ffffffffa00ecadc>] xennet_remove+0x2c/0x80 [xen_netfront] [ 392.348516] [<ffffffff81481c69>] xenbus_dev_remove+0x59/0xc0 [ 392.356257] [<ffffffff814e7217>] __device_release_driver+0x87/0x120 [ 392.364645] [<ffffffff814e7cf8>] driver_detach+0xb8/0xc0 [ 392.371989] [<ffffffff814e6e69>] bus_remove_driver+0x59/0xe0 [ 392.379883] [<ffffffff814e84f0>] driver_unregister+0x30/0x70 [ 392.387495] [<ffffffff814814b2>] xenbus_unregister_driver+0x12/0x20 [ 392.395908] [<ffffffffa00ed89b>] netif_exit+0x10/0x775 [xen_netfront] [ 392.404877] [<ffffffff81124e08>] SyS_delete_module+0x1d8/0x230 [ 392.412804] [<ffffffff8179a8ee>] system_call_fastpath+0x12/0x71 Signed-off-by: Chas Williams <3chas3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27UBI: return ENOSPC if no enough space availableshengyong
[ Upstream commit 7c7feb2ebfc9c0552c51f0c050db1d1a004faac5 ] UBI: attaching mtd1 to ubi0 UBI: scanning is finished UBI error: init_volumes: not enough PEBs, required 706, available 686 UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1) UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM UBI error: ubi_init: cannot attach mtd1 If available PEBs are not enough when initializing volumes, return -ENOSPC directly. If available PEBs are not enough when initializing WL, return -ENOSPC instead of -ENOMEM. Cc: stable@vger.kernel.org Signed-off-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27UBI: Validate data_sizeRichard Weinberger
[ Upstream commit 281fda27673f833a01d516658a64d22a32c8e072 ] Make sure that data_size is less than LEB size. Otherwise a handcrafted UBI image is able to trigger an out of bounds memory access in ubi_compare_lebs(). Cc: stable@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27cpufreq: dt: Tolerance applies on both sides of target voltageViresh Kumar
[ Upstream commit a2022001cebd0825b96aa0f3345ea3ad44ae79d4 ] Tolerance applies on both sides of the target voltage, i.e. both min and max sides. But while checking if a voltage is supported by the regulator or not, we haven't taken care of tolerance on the lower side. Fix that. Cc: Lucas Stach <l.stach@pengutronix.de> Fixes: 045ee45c4ff2 ("cpufreq: cpufreq-dt: disable unsupported OPPs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27USB: Add reset-resume quirk for two Plantronics usb headphones.Yao-Wen Mao
[ Upstream commit 8484bf2981b3d006426ac052a3642c9ce1d8d980 ] These two headphones need a reset-resume quirk to properly resume to original volume level. Signed-off-by: Yao-Wen Mao <yaowen@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: Add device quirk for Logitech PTZ camerasVincent Palatin
[ Upstream commit 72194739f54607bbf8cfded159627a2015381557 ] Add a device quirk for the Logitech PTZ Pro Camera and its sibling the ConferenceCam CC3000e Camera. This fixes the failed camera enumeration on some boot, particularly on machines with fast CPU. Tested by connecting a Logitech PTZ Pro Camera to a machine with a Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles while recording the kernel logs and taking camera picture after each boot. Before the patch, more than 7% of the boots show some enumeration transfer failures and in a few of them, the kernel is giving up before actually enumerating the webcam. After the patch, the enumeration has been correct on every reboot. Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: musb: cppi41: allow it to work againFelipe Balbi
[ Upstream commit b0a688ddcc5015eb26000c63841db7c46cfb380a ] since commit 33c300cb90a6 ("usb: musb: dsps: don't fake of_node to musb core") we have been preventing CPPI 4.1 from probing due to NULL of_node. We can't revert said commit otherwise a different regression would show up, so the fix is to look for the parent device's (glue layer's) of_node instead, since that's the thing which is actually described in DTS. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: Use the USB_SS_MULT() macro to get the burst multiplier.Mathias Nyman
[ Upstream commit ff30cbc8da425754e8ab96904db1d295bd034f27 ] Bits 1:0 of the bmAttributes are used for the burst multiplier. The rest of the bits used to be reserved (zero), but USB3.1 takes bit 7 into use. Use the existing USB_SS_MULT() macro instead to make sure the mult value and hence max packet calculations are correct for USB3.1 devices. Note that burst multiplier in bmAttributes is zero based and that the USB_SS_MULT() macro adds one. Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: chipidea: udc: using the correct stall implementationPeter Chen
[ Upstream commit 56ffa1d154c7e12af16273f0cdc42690dd05caf5 ] According to spec, there are functional and protocol stalls. For functional stall, it is for bulk and interrupt endpoints, below are cases for it: - Host sends SET_FEATURE request for Set-Halt, the udc driver needs to set stall, and return true unconditionally. - The gadget driver may call usb_ep_set_halt to stall certain endpoints, if there is a transfer in pending, the udc driver should not set stall, and return -EAGAIN accordingly. These two kinds of stall need to be cleared by host using CLEAR_FEATURE request (Clear-Halt). For protocol stall, it is for control endpoint, this stall will be set if the control request has failed. This stall will be cleared by next setup request (hardware will do it). It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt" test failure, meanwhile, this change has been verified by USB2 CV Compliance Test and MSC Tests. Cc: <stable@vger.kernel.org> #3.10+ Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27regmap: debugfs: Don't bother actually printing when calculating max lengthMark Brown
[ Upstream commit 176fc2d5770a0990eebff903ba680d2edd32e718 ] The in kernel snprintf() will conveniently return the actual length of the printed string even if not given an output beffer at all so just do that rather than relying on the user to pass in a suitable buffer, ensuring that we don't need to worry if the buffer was truncated due to the size of the buffer passed in. Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27regmap: debugfs: Ensure we don't underflow when printing access masksMark Brown
[ Upstream commit b763ec17ac762470eec5be8ebcc43e4f8b2c2b82 ] If a read is attempted which is smaller than the line length then we may underflow the subtraction we're doing with the unsigned size_t type so move some of the calculation to be additions on the right hand side instead in order to avoid this. Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27PM / AVS: rockchip-io: depend on CONFIG_POWER_AVSHeiko Stuebner
[ Upstream commit 28c1f1628ee4b163e615eefe1b6463e3d229a873 ] The rockchip io-domain driver currently only depends on ARCH_ROCKCHIP itself. This makes it possible to select the power-domain driver, but not the POWER_AVS class and results in the iodomain-driver not getting build in this case. So add the additional dependency, which also results in the driver config option now being placed nicely into the AVS submenu. Fixes: 662a958638bd ("PM / AVS: rockchip-io: add driver handling Rockchip io domains") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27mtd: pxa3xx_nand: add a default chunk sizeAntoine Ténart
[ Upstream commit bc3e00f04cc1fe033a289c2fc2e5c73c0168d360 ] When keeping the configuration set by the bootloader (by using the marvell,nand-keep-config property), the pxa3xx_nand_detect_config() function is called and set the chunk size to 512 as a default value if NDCR_PAGE_SZ is not set. In the other case, when not keeping the bootloader configuration, no chunk size is set. Fix this by adding a default chunk size of 512. Fixes: 70ed85232a93 ("mtd: nand: pxa3xx: Introduce multiple page I/O support") Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Robert Jarzmik <robert.jarzmik@free> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27fbdev: select versatile helpers for the integratorLinus Walleij
[ Upstream commit 2701fa0864ecb9e49d47a4aa1c02f172ab79639a ] Commit 11c32d7b6274cb0f554943d65bd4a126c4a86dcd "video: move Versatile CLCD helpers" missed the fact that the Integrator/CP is also using the helper, and as a result the platform got only stubs and no graphics. Add this as a default selection to Kconfig so we have graphics again. Fixes: 11c32d7b6274 (video: move Versatile CLCD helpers) Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: xhci: Add support for URB_ZERO_PACKET to bulk/sg transfersReyad Attiyat
[ Upstream commit 4758dcd19a7d9ba9610b38fecb93f65f56f86346 ] This commit checks for the URB_ZERO_PACKET flag and creates an extra zero-length td if the urb transfer length is a multiple of the endpoint's max packet length. Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27xhci: init command timeout timer earlier to avoid deleting it uninitializedMathias Nyman
[ Upstream commit cc8e4fc0c3b5e8340bc8358990515d116a3c274c ] Don't check if timer is running with a timer_pending() before deleting it with del_timer_sync(), this defies the whole point of the sync part and can cause a possible race. Instead we just want to make sure the timer is initialized early enough before we have a chance to delete it. Cc: <stable@vger.kernel.org> Reported-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27xhci: change xhci 1.0 only restrictions to support xhci 1.1Mathias Nyman
[ Upstream commit dca7794539eff04b786fb6907186989e5eaaa9c2 ] Some changes between xhci 0.96 and xhci 1.0 specifications forced us to check the hci version in code, some of these checks were implemented as hci_version == 1.0, which will not work with new xhci 1.1 controllers. xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these checks to hci_version >= 1.0 Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: xhci: exit early in xhci_setup_device() if we're halted or dyingRoger Quadros
[ Upstream commit 448116bfa856d3c076fa7178ed96661a008a5d45 ] During quick plug/removal of OTG adapter during dual-role testing it can happen that xhci_alloc_device() is called for the newly detected device after the DRD library has called xhci_stop to remove the HCD. If that is the case, just fail early to prevent the following warning. [ 154.732649] hub 4-0:1.0: USB hub found [ 154.742204] hub 4-0:1.0: 1 port detected [ 154.824458] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 154.854609] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 154.944430] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ 154.951009] xhci-hcd xhci-hcd.0.auto: xhci_setup_device [ 155.038191] xhci-hcd xhci-hcd.0.auto: remove, state 4 [ 155.043315] usb usb4: USB disconnect, device number 1 [ 155.055270] xhci-hcd xhci-hcd.0.auto: xhci_stop [ 155.060094] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered [ 155.066576] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 155.071710] usb usb3: USB disconnect, device number 1 [ 155.077124] xhci-hcd xhci-hcd.0.auto: xhci_setup_device [ 155.082389] ------------[ cut here ]------------ [ 155.087690] WARNING: CPU: 0 PID: 72 at drivers/usb/host/xhci.c:3800 xhci_setup_device+0x410/0x484 [xhci_hcd]() [ 155.097861] Modules linked in: sd_mod usb_storage scsi_mod usb_f_ss_lb g_zero libcomposite ipv6 xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev ti_am335x_adc joydev kfifo_buf industrialio snd_soc_simple_cc [ 155.146734] CPU: 0 PID: 72 Comm: kworker/0:3 Tainted: G W 4.1.4-00834-gcd9380b-dirty #50 [ 155.156073] Hardware name: Generic AM43 (Flattened Device Tree) [ 155.162117] Workqueue: usb_hub_wq hub_event [usbcore] [ 155.167249] Backtrace: [ 155.169751] [<c0012af0>] (dump_backtrace) from [<c0012c8c>] (show_stack+0x18/0x1c) [ 155.177390] r6:c089d4a4 r5:ffffffff r4:00000000 r3:ee46c000 [ 155.183137] [<c0012c74>] (show_stack) from [<c05f7c14>] (dump_stack+0x84/0xd0) [ 155.190446] [<c05f7b90>] (dump_stack) from [<c00439ac>] (warn_slowpath_common+0x80/0xbc) [ 155.198605] r7:00000009 r6:00000ed8 r5:bf27eb70 r4:00000000 [ 155.204348] [<c004392c>] (warn_slowpath_common) from [<c0043a0c>] (warn_slowpath_null+0x24/0x2c) [ 155.213202] r8:ee49f000 r7:ee7c0004 r6:00000000 r5:ee7c0158 r4:ee7c0000 [ 155.220051] [<c00439e8>] (warn_slowpath_null) from [<bf27eb70>] (xhci_setup_device+0x410/0x484 [xhci_hcd]) [ 155.229816] [<bf27e760>] (xhci_setup_device [xhci_hcd]) from [<bf27ec10>] (xhci_address_device+0x14/0x18 [xhci_hcd]) [ 155.240415] r10:ee598200 r9:00000001 r8:00000002 r7:00000001 r6:00000003 r5:00000002 [ 155.248363] r4:ee49f000 [ 155.250978] [<bf27ebfc>] (xhci_address_device [xhci_hcd]) from [<bf20cb94>] (hub_port_init+0x1b8/0xa9c [usbcore]) [ 155.261403] [<bf20c9dc>] (hub_port_init [usbcore]) from [<bf2101e0>] (hub_event+0x738/0x1020 [usbcore]) [ 155.270874] r10:ee598200 r9:ee7c0000 r8:ee7c0038 r7:ee518800 r6:ee49f000 r5:00000001 [ 155.278822] r4:00000000 [ 155.281426] [<bf20faa8>] (hub_event [usbcore]) from [<c005754c>] (process_one_work+0x128/0x340) [ 155.290196] r10:00000000 r9:00000003 r8:00000000 r7:fedfa000 r6:eeec5400 r5:ee598314 [ 155.298151] r4:ee434380 [ 155.300718] [<c0057424>] (process_one_work) from [<c00578f8>] (worker_thread+0x158/0x49c) [ 155.308963] r10:ee434380 r9:00000003 r8:eeec5400 r7:00000008 r6:ee434398 r5:eeec5400 [ 155.316913] r4:eeec5414 [ 155.319482] [<c00577a0>] (worker_thread) from [<c005cc40>] (kthread+0xdc/0xf8) [ 155.326765] r10:00000000 r9:00000000 r8:00000000 r7:c00577a0 r6:ee434380 r5:ee4441c0 [ 155.334713] r4:00000000 r3:00000000 [ 155.338341] [<c005cb64>] (kthread) from [<c000fc08>] (ret_from_fork+0x14/0x2c) [ 155.345626] r7:00000000 r6:00000000 r5:c005cb64 r4:ee4441c0 [ 155.356108] ---[ end trace a58d34c223b190e6 ]--- [ 155.360783] xhci-hcd xhci-hcd.0.auto: Virt dev invalid for slot_id 0x1! [ 155.574404] xhci-hcd xhci-hcd.0.auto: xhci_setup_device [ 155.579667] ------------[ cut here ]------------ Cc: <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27usb: xhci: Clear XHCI_STATE_DYING on startRoger Quadros
[ Upstream commit e5bfeab0ad515b4f6df39fe716603e9dc6d3dfd0 ] For whatever reason if XHCI died in the previous instant then it will never recover on the next xhci_start unless we clear the DYING flag. Cc: <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2015-10-27USB: whiteheat: fix potential null-deref at probeJohan Hovold
[ Upstream commit cbb4be652d374f64661137756b8f357a1827d6a4 ] Fix potential null-pointer dereference at probe by making sure that the required endpoints are present. The whiteheat driver assumes there are at least five pairs of bulk endpoints, of which the final pair is used for the "command port". An attempt to bind to an interface with fewer bulk endpoints would currently lead to an oops. Fixes CVE-2015-5257. Reported-by: Moein Ghasemzadeh <moein@istuary.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-18 18:21:34 +0000